MC-10-27-37 ® Specification: MIFAB Series MC-10-27-37 (Specify L for left or R for right design) single, horizontal, adjustable, water closet carrier with lacquered, 37" (940) long barrel cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, 2" (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support. Function: Used with off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The 37” long barrel fitting eliminates the time and material required to install a battery of standard 13" long fittings. The auxiliary inlet is designed to receive waste from urinals and lavatories beside or opposite the closet carrier in order to reduce the amount of space required in the pipe chase. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted. USA: 1-800-465-2736 www.mifab.com CAN: 1-800-387-3880 HORIZONTAL, ADJUSTABLE, WATER CLOSET CARRIER WITH AUXILIARY INLET and 37” LONG BARREL 2012-06-15 ® MIFAB reserves the right to make changes in material and design without formal notice and obligation. Page CR10 Job Name: Section No: Schedule No: Page No: Contractor: Purchase Order No: Note: 10 1/2" (267) minimum space required between front of foot and rear of anchor support. 8" (203) minimum in wall space required between back of rear anchor support and back of in wall foot supports. Note: Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design. Note: 8” tapered thread ABS nipple shipped standard with MC-10 Series carriers. The universal faceplate assembly accepts all nipple variations, rolling thread (-OR), cast iron (-CI) and tapered thread ABS with adjustable horn (-AH). 17 3/4” 9” 18” 7 1/2” 1” MIN MAX 0” +4” INLET C/L TO FLOOR ADJ. RANGE MIN MAX 4 1/2” 9 1/2” INLET C/L TO BARREL C/L ADJ. RANGE MC-10,12,13 UNIVERSAL FACEPLATE ASSEMBLY BREAKAWAY TABS CENTERLINE OF NIPPLE TO FLOOR MC-10L-27-37 4 1/8” DIMENSION BETWEEN AUXILIARY INLET AND VENT IS IDEAL FOR A STANDARD WYE AND 1/8th BEND CONNECTION MC-10-27-37 Series Meets ANSI/ASME fixture carrier standard A112.6.1M-97 BOTTOM OF FIRST CUT = 4 1/2” BOTTOM OF SECOND CUT = 5 1/4” “X”=4” MIN TO 6-1/4 MAX WALL THICKNESS WITH STANDARD NIPPLE. MIN OF 5/8” POSSIBLE WITH SHORTENED NIPPLE Note: left hand version illustrated. Right hand is mirror image. BOTTOM OF FACEPLATE = 7” FOOT SUPPORTS SHOULD BE SECURELY ANCHORED TO FLOOR WITH 1/2” (13) BOLTS AND ANCHORS BY OTHERS 1/2” (13) TAPPING FOR STRUT MOUNTED FLUSH VALVE WATER SUPPLY INCORPORATED INTO BACK OF CARRIER FACEPLATE 500 Lb. Load Rating OPTIONAL VARIATIONS: SUFFIX 8" ABS nipple with adjustable horn -AH8 12" ABS nipple with adjustable horn -AH12 4" rolling thread cast iron nipple -CI-4 6" rolling thread cast iron nipple -CI-6 8" rolling thread cast iron nipple -CI-8 12" rolling thread cast iron nipple -CI-12 24" rolling thread cast iron nipple -CI-24 Hub and spigot connection -HS Left hand fitting -L 8" rolling thread ABS nipple -OR8 Heavy duty 500 lb. load rated carrier -HD Heavy duty 750 lb. load rated carrier -HD-750 Extra heavy duty 1,000 lb. load rated carrier -HDX 12” rolling thread ABS nipple -OR12 Buy American Act compliant product -BA Pennsylvania Steel Act compliant product SUFFIX Right hand fitting -R Finishing / Tiling frame -1 Auxiliary support, recommended with -10 nipple lengths over 12” 12" tapered thread ABS nipple -12 Galvanized cast iron -13 Vandal proof finish trim -14 Test plug for custom and cast iron nipples Nipple wrench -19 Flush valve support -20 -PA -17 Prefabricated carrier -PFAB Location: 3” 3 37” 2” AUXILIARY INLET 6 3/4” 4 ½” 4” 2 3/4” 1” 9 ½” 2” VENT CONNECTION “X” FINISHED WALL 2 1/4” 4 1/ ”
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
MC-10-27-37® Specification: MIFAB Series MC-10-27-37 (Specify L for left or R for right design) single, horizontal, adjustable, water closet
carrier with lacquered, 37" (940) long barrel cast iron fitting, 4" (102) no hub waste, 2" (51) no hub vent connection, 2" (51) no hub auxiliary inlet connection, lacquered cast iron gasketed adjustable faceplate, universal floor mounted cast iron foot supports, adjustable 8" tapered thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors, polished chrome plated finishing cap nuts and rear anchor tie down support.
Function: Used with off the floor plumbing fixtures that are wall mounted and have no contact with the finished floor. The 37” long barrel fitting eliminates the time and material required to install a battery of standard 13" long fittings. The auxiliary inlet is designed to receive waste from urinals and lavatories beside or opposite the closet carrier in order to reduce the amount of space required in the pipe chase. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.
USA: 1-800-465-2736 www.mifab.com CAN: 1-800-387-3880
HORIZONTAL, ADJUSTABLE, WATER CLOSETCARRIER WITH AUXILIARY INLET and 37” LONG BARREL
2012-06-15
®
MIFAB reserves the right to make changes in material and design without formal notice and obligation.
Page CR10
Job Name:
Section No:
Schedule No:
Page No:
Contractor:
Purchase Order No:
Note: 10 1/2" (267) minimum space required between front of foot and rear of anchor support. 8" (203) minimum in wall space required between back of rear anchor support and back of in wall foot supports.Note: Foot supports and faceplate are assembled at the factory before shipment in the typical siphon jet water closet configuration and are reversible for the blowout water closet design.
Note: 8” tapered thread ABS nipple shipped standard with MC-10 Series carriers. The universal faceplate assembly accepts all nipple variations, rolling thread (-OR), cast iron (-CI) and tapered thread ABS with adjustable horn (-AH).
17 3/4”
9”
18”
7 1/2”
1”
MIN MAX0” +4”
INLET C/L TO FLOORADJ. RANGE
MIN MAX4 1/2” 9 1/2”
INLET C/L TO BARRELC/L ADJ. RANGE
MC-10,12,13UNIVERSAL
FACEPLATE ASSEMBLY
BREAKAWAY TABS CENTERLINE OF NIPPLE TO FLOOR
MC-10L-27-37
4 1/8” DIMENSION BETWEEN AUXILIARYINLET AND VENT IS IDEAL FOR A STANDARD WYE AND 1/8th BEND CONNECTION
MC-10-27-37 SeriesMeets ANSI/ASME
fixture carrier standardA112.6.1M-97
BOTTOM OF FIRST CUT = 4 1/2”
BOTTOM OF SECOND CUT = 5 1/4”
“X”=4” MIN TO 6-1/4 MAXWALL THICKNESS WITH STANDARD
NIPPLE. MIN OF 5/8” POSSIBLEWITH SHORTENED NIPPLE
Note: left hand versionillustrated. Right hand is mirror image.
BOTTOM OF FACEPLATE = 7”
FOOT SUPPORTS SHOULD BE SECURELY ANCHORED TO FLOOR WITH 1/2” (13) BOLTS AND ANCHORS BY OTHERS
1/2” (13) TAPPING FOR STRUT MOUNTED FLUSH VALVE WATER SUPPLY INCORPORATED INTO BACK OF CARRIER FACEPLATE
500 Lb. Load Rating
OPTIONAL VARIATIONS:SUFFIX8" ABS nipple with adjustable horn -AH812" ABS nipple with adjustable horn -AH12
4" rolling thread cast iron nipple -CI-46" rolling thread cast iron nipple -CI-68" rolling thread cast iron nipple -CI-812" rolling thread cast iron nipple -CI-1224" rolling thread cast iron nipple -CI-24
Hub and spigot connection -HSLeft hand fitting -L8" rolling thread ABS nipple -OR8
Heavy duty 500 lb. load rated carrier -HDHeavy duty 750 lb. load rated carrier-HD-750Extra heavy duty 1,000 lb. load rated carrier-HDX
12” rolling thread ABS nipple -OR12
Buy American Act compliant product -BAPennsylvania Steel Act compliant product
SUFFIX
Right hand fitting -R
Finishing / Tiling frame -1Auxiliary support, recommended with -10nipple lengths over 12”12" tapered thread ABS nipple -12 Galvanized cast iron-13Vandal proof finish trim -14Test plug for custom and cast iron nipplesNipple wrench -19Flush valve support -20
-PA
-17
Prefabricated carrier -PFAB
Location:
37”
9 1/2”
1”
2 3/4”
7”
2 3/8” 5 1/2”
5 1/2”
“X”
FINISHING WALL
4”
4 1/2”
1 3/4”
2” VENT CONNECTION
2” AUXILIARY INLET
3”
337”2” AUXILIARY
INLET
6 3/4”4 ½”
4”
2 3/4”
1”
9 ½”
2” VENT CONNECTION
“X”
FINISHED WALL2 1/4” 4 1/8”
Related Documents
