This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Belt MaintenanceProduct Catalogue
Belt Lacing Systems for the Laundry Industry
MATO GmbH & Co. KG · Germany · [email protected] · www.mato.deBranch Herten: Hohewardstraße 329 · D-45699 Herten · Phone: +49 (0) 2366-9321-0 · Fax: +49 (0) 2366-9321-10Head Office: Benzstraße 16–24 · D-63165 Mühlheim a.M. · Phone: +49 (0) 6108-906-0 · Fax: +49 (0) 6108-906-120 s i n c e 1 9 0 6
Page
Selection Charts for Wire Systems M and R for the Laundry Industry 3
Low Profile Wire Fastener M61.2LSW, Cut to Length 4-5
Low Profile Wire Fastener M61.2LNW, Cut to Length 6-7
Rectangular Wire Fastener M63LP, Cut to Length 8
Round Wire Fasteners R20 and R70 9
Fastener Series M60L-P (MATOPATCH) 10-12
Installation Units for MATOPATCH 13
Selection Chart of Connecting Pins for the Laundry Industry 14
Connecting Pins for the Laundry Industry 15-16
Installation Units and Accessories for the Laundry Industry 18
Terms & Conditions, General Remarks 19-20
Page 1
Table of ContentsBelt Lacing Systems for the Laundry Industry
Ve
rbin
de-
st
ab-
typ
Ab
kürz
un
g
Ve
rbin
de
sta
b-
ve
rsc
hle
iss
-fe
sti
gk
eit
Ve
rbin
de
r-s
tan
dze
it
Ko
rro
sio
ns
-b
estä
nd
igke
it
Sä
ure
-b
estä
nd
igke
it
Ma
gn
etis
mu
s
Ste
ifig
ke
it
Fle
xib
ilit
ät
We
ch
se
lnd
e
Gu
rts
pa
nn
un
g,
sc
hm
ale
Gu
rte
NylostahlNylonummante lte r Federstahld rah t
NylorostfreiNylonummante lte r Edelstahld raht
Nylonrundmat er ial, glat t
Nylonrundmat er ial, gepräg te Kerben
Edelstahld raht, gla tt
Edelstahld raht, gepräg te Kerben
NylostahllitzeNylonummante ltes Stahld rahts eil
NylorostfreilitzeNylonummante ltes
sehr gut gutm äßig m äßigstark
m agnetischsehr gut
Bestimmung des Verbindestabtyps
...NCS
aus-gezeichnet
aus-gezeichnet
aus-
gezeichnet
aus-
gezeichnet
aus-reichend
gut
aus-gezeichnet
aus-gezeichnet
...NST
sehr gutschwach
m agnetischsehr gut
...NC
...NSS sehr gut gut
aus-
gezeichnet
aus-
gezeichnet
aus-
gezeichnet
aus-
gezeichnet
nicht
m agnetisch
aus-
reichend
aus-
gezeichnet
aus-
gezeichnet
sehr gut sehr gutschwach
m agnetischaus-
gezeichnet
aus-gezeichnet
aus-gezeichnet
gut gut
gut
aus-
gezeichnet
aus-gezeichnet
sehr gutschwach
m agnetischgut
gering
m agnetisch gut sehr gut
Nyloschnur
...NY
...NYN
Stahldraht rostfre i
...WSS
...WSSN*
aus-reichend
aus-gezeichnet
sehr gut gut
gut
Edelstahls eil
P1 = Verbinder m it vorinstall iertem Textilpatch
Verbinderauswahl Drahtsysteme M und R
Papiergefasst: Verbinder i n Papier geh altenQuerdraht: Verb inder auf Qu erdraht geschweißt
M61.2L = Flachdraht
M = Profi ldrahtR = Runddraht
Weitere E rläuterungen:
Materialauswahl entsprechend Ihren Anforderungen siehe Auswahl tabelle unten.
Min. Verbindestab
Trom mel Durchm .
Durchm. m m inch mm m m (Typ)
75mm3" 0,9x0,7 .035x.028 2,54 1,8 (MK18)
R22SP R72SP
R22NP
R72NP
2,0mm 3,0mm
R23SP
1,0mm 4,0mm
R73SP
R23NP
Teilung
3/64 " 5/64" 1/8"
50mm 2"
Abmessungen 1/32" 1/16"Draht Gurtdickenbereich
Verbinder- und Verbindestabauswahltabelle für Systeme M60-sonder, R20 und R70
5/64" 3/32" 1/8" 9/64 "
0,8mm 1,6mm 2,0mm 2,4mm
M61.2LSW-P1
M63LP
M61.2LNW
5/32"
R73NP
75mm 3"
1,0 .040 3,1751,8 (MK18)
2,0 (MK20)
1,8 (MK18)
25mm 1"
30mm 1 1/8"
0,9x0,5
0,9x0,5
.035x.020
.035x.020
2,54
2,54
1,5 (MK15)
1,5 (MK15)
2,0 (MK20) 1,0 .040 3,175
M61.2LNW-P1
M61.2LSW
7/64"
2,8mm
5/32"
4,0mm3,2mm 3,6mm
Was brauchen Sie?Gurtdicke
Trommeldurchmesser (Dmin )
Werkstoff Kurz
form
Mag
netis
mus
Verschleiß-
widers
tand
(Lebe
nsd
auer)
Säur
e-
beständigke
it
Korrosions
-
beständigke
it
Schu
tz d
urch
Abde
ckung
Verfügbare Systeme
Stahl verzinkt G stark magn etisch
sehr gut ungenü gen d gut n ein R20
Stahl rostfrei, 1.4016 S magn etisch sehr gut g ut gut n ein R20, R70, M60
Stahl rostfrei, 1.4404 SS schwach magn etisch
sehr gut sehr g utaus-
gezeichn etn ein R20, R70, M60
Auswahltabelle Verbindermaterial
Stahl rostfrei, 1.4404
mit Textilpatch
SS - P1
schwach magn etisch
aus-gezeichnet
sehr g utaus-
gezeichn etja M60L-P1
Wie gehen Sie vor?Auswahltabellen unten , treffen mehrere Typen zu, dann wählen Sie:
- kleinste Drahtabmessung , wenn Wunsch na ch flachem Auftrag = ruhige r Lauf. - größte Drahtabmessung , we nn h oher Verschleiß. - P1 (mit Textilpatch) , wenn Ab deckung g ewünscht.
Verbindestabauswahl s iehe Sei te 14
Page 2
Wire Systems M and R for the Laundry Industry
P : Fasteners with preinstalled Textile Patch (MATOPATCH)
for the most uncommon problems.
Page 3
Selection ChartWire Systems M and R for the Laundry Industry
Fastener Selection for the Laundry Industry
M = Rectangular WireR = Round Wire
Further ExplanationsCarded: Fasteners are positioned in carded paper
Barred : Fasteners are welded on cross wireM61.2L = Low Profile Rectangular Wire
MATO helps you choosing the right fastener for your application and offers perfect solutions even
Material Selection according to your requirements, see Selection Chart below.
What do you require?Determine: Belt Thickness
Minimum Pulley Dia (D min )
How do you select?Selection Charts below , if several types apply, then select :
- Smallest Wire Dimension for a smooth surface, results in less noise
- Biggest Wire Dimension , when dealing with high wear.
- P (with Textile Patch = MATOPATCH) , when cover is required.
Selection of Connecting Pins, see page 14
Material Mat
eri
al
S
ymb
ol
Mag
net
ic
Ab
rasi
on
R
esi
sta
nce
Ch
emic
al
Resi
sta
nce
Ru
st
R
esi
sta
nce
Pro
tect
ion
th
rou
gh
C
ove
rin
g
Available Systems
Galvanised Steel GHigh
MagneticVery Good No Good No R20
Stainless Steel, 430 S Magnetic Very Good Good Good No R20, R70, M60
Stainless Steel, 316 SSSlightly
MagneticVery Good Very Good Excellent No R20, R70, M60
Fastener Material Selection Chart
Stainless Steel, 316 with Textile Patch
SS-PSlightly
MagneticExcellent Very Good Excellent Yes M60L-P
Min. Connecting
Pulley Pin Diameter
Dia. mm inch mm mm (type)
75mm3" 0.9x0.7 .035x.028 2.54 1.8 (MK18)
2.8mm
5/32"
4.0mm3.2mm 3.6mm
M61.2LNW-P
M61.2LSW
1.5 (MK15)
2.0 (MK20)
1.0 .040 3.175
1.8 (MK18)
1.5 (MK15)
2.0 (MK20)
1.8 (MK18)
25mm 1"
30mm 1 1/8"
0.9x0.5
0.9x0.5
.035x.020
.035x.020
2.54
2.54
75mm 3"
1.0 .040 3.17550mm
2"
R73NP
4.0mm
R73SP
M61.2LNW
5/32"
Wire Belt Thickness Range
Fastener and Connecting Pin Selection Chart for Systems M60-special, R20 and R70
5/64" 3/32" 1/8" 9/64"7/64"Dimensions 1/32" 1/16"
0.8mm 1.6mm
M61.2LSW-P
Pitch
3/64" 5/64" 1/8"
2.0mm 2.4mm
M63LP
R23NP
2.0mm 3.0mm
R23SP
1.0mm
R22SP
R72SP
R22NP
R72NP
- Minimum Pulley Diameter 30 mm
Description Belt Width Fasteners No. of Order No kg
Connecting Pins MK18-NYN, Cut to Length upon request
Special Connecting Pins on page 15
Page 8
Rectangular Wire Fastener M63LP, Cut to Length
- Barred Fasteners - Box Content with Connecting Pin MK15-NYN
0.9 x 0.7 mm
0.9 x 0.7 mm
- Pitch 2.54 mm - Belt Thickness 3.2 - 4.0 mm
- R20 = Carded Fastener - Box without Connecting Pins
Description Belt Thickness Min. Pulley Strips/ Order No kg
Diameter-Ø Box
R20 StandardStainless Steel, Strip Length 300 mm
R22SP-SS-300-12 2.0 - 3.0 mm 50 mm 12 42 104 22 21 0,3
R22NP-SS-300-12 3.0 - 4.0 mm 50 mm 12 42 104 22 22 0,3
R23SP-SS-300-12 2.0 - 3.0 mm 75 mm 12 42 104 22 31 0,4
R23NP-SS-300-12 3.0 - 4.0 mm 75 mm 12 42 104 22 32 0,4
Stainless Steel 316
Chromium Steel, Strip Length 300 mm
R22SP-S-300-12 2.0 - 3.0 mm 50 mm 12 42 103 22 21 0,3
R22NP-S-300-12 3.0 - 4.0 mm 50 mm 12 42 103 22 22 0,3
R23SP-S-300-12 2.0 - 3.0 mm 75 mm 12 42 103 22 31 0,4
R23NP-S-300-12 3.0 - 4.0 mm 75 mm 12 42 103 22 32 0,4
Chromium Steel 430
Galvanised Steel, Strip Length 300 mm
R22SP-G-300-12 2.0 - 3.0 mm 50 mm 12 42 101 22 21 0,3
R22NP-G-300-12 3.0 - 4.0 mm 50 mm 12 42 101 22 22 0,3
R23SP-G-300-12 2.0 - 3.0 mm 75 mm 12 42 101 22 31 0,4
R23NP-G-300-12 3.0 - 4.0 mm 75 mm 12 42 101 22 32 0,4
Galvanised Steel
R70 StandardStainless Steel, Strip Length 300 mm
R72SP-SS-300-12 2.0 - 3.0 mm 50 mm 12 42 704 17 21 0,3
R72NP-SS-300-12 3.0 - 4.0 mm 50 mm 12 42 704 17 22 0,4
R73SP-SS-300-12 2.0 - 3.0 mm 75 mm 12 42 704 17 31 0,4
R73NP-SS-300-12 3.0 - 4.0 mm 75 mm 12 42 704 17 32 0,5
Stainless Steel 316
Chromium Steel, Strip Length 300 mm
R72SP-S-300-12 2.0 - 3.0 mm 50 mm 12 42 703 17 21 0,3
R72NP-S-300-12 3.0 - 4.0 mm 50 mm 12 42 703 17 22 0,4
R73SP-S-300-12 2.0 - 3.0 mm 75 mm 12 42 703 17 31 0,4
R73NP-S-300-12 3.0 - 4.0 mm 75 mm 12 42 703 17 32 0,5
Chromium Steel 430
Round Wire Fastener R70, Cut to Length upon request
Connecting pins on page 16
Page 9
- Wire Diameter 1.0mm
Round Wire Fasteners R20 and R70
- Pitch 3.175 mm
- R70 = Barred Fastener
Page 10
Fastener Series M60L-P (MATOPATCH)
Page 11
Fastener Series M60L-P (MATOPATCH)Innovation for the Laundry Industry
MATOPATCH Fasteners are designed in a way that fastener and patch can be installed in basically one step using according installation units (see page 13). Additional glue and drying time or use of dangerous materials no longer apply.
The lifespan of MATOPATCH Lacing System is usually 4 times higher as the current state of Technology or as similar looking fasteners in the same field of use. Another feature of this Belt Lacing System worth mentioning is an integrated protection against belt wear, low abrasive wear and is low in noise emission.
There are currently two sizes covering the standard laundry belt thickness, ranging from 1.6mm up to 3.2mm (see page 12).
MATO Rectangular Wire Fastener Series M60L-P (MATOPATCH) has been specifically developed for the Laundry Industry. This patented system takes a huge leap regarding life, design and installation of larger series.
We can customize the already excellent design of our fasteners by printing upon your request.
Using this fastener you or your customers will have the advantage of the safest, most enduring and optically most appealing Belt Lacing System. There will be no more laundry getting caught, paper scraps or glue residue.
Our Barred Rectangular Wire Fastener, Stainless Steel with preinstalled textile patch are very suitable for cotton and felt belts and offer optimum protection against damage of your laundry.
Belt Cleaning Systems will be treated gently.
- P10 = Plain PatchDescription Belt Width Fasteners No of Order No kg mm Per Strip Laces
M61.2LSW-P10, Cut to LengthBelt Thickness 1.6 - 2.4 mm
- Box with Connecting Pin MK15-NYN - Minimum Pulley Diameter 25 mm
MATOPATCH M61.2 - PSpecial Design with Patch for the Laundry Industry
- Barred Fastener - Fastener preinstalled with Patch
- 1 Phase - Voltage: 230V - 50 HzDescription Lacing Width/ Pitch Order No kg
Comb Width (mm)
MATOPATCHLEVERInstallation Width 60 mm
MATOPATCHLEVER 60WP 60 mm 2,54 42 480 96 60 6,0
The MATOPATCHLEVER 60WP has been developed for site independent installations of the very durable MATOPATCHfastener. Since this tool is independent from a vice, it enables you to install fasteners directly into diverse machines of large-scale laundriesThe MATOPATCHLEVER has been designed for a maximum comb width of 60 mm of the Belt Fasteners M61.2LSW-P1 or M61.2LNW-P1.
The MATOPATCHVICE 260WP has been developed for installations of small and medium series of our very durable MATOPATCH Fastener, which is used in a vice. After utilization of the conversion kit MATOHYD 260WP, the tool can be used in the electro-hydraulic Lacing Tool MATOHYD 200W (see page 17).
The MATOPATCHVICE 260WP has been designed for a maximumcomb width of 120 mm of the Fasteners M61.2LSW-P1 or M61.2LNW-P1. All other fasteners with a pitch of 2.54mm can be installed in this range.
Installation Units for installation of larger series upon request.
Page 13
Lacing Tools for MATOPATCH
Connecting Load - Power Input: 0.6 kW
M63LP can be run with MK15NYN as well.
Page 14
Selection ChartsConnecting Pins for Wire Systems M and R for the Laundry Industry
The MATO Connecting Pins are aligned in design and material composition to the MATO Fasteners. Choosing the right Connecting Pin is an important contribution to reach the optimum performance of the splice in your application.We recommend our cut to belt width nylon pins (notched) for typical laundry applications such as e. g. folding machines
M61.2LSW M63LP R22NP
M61.2LNW R22SP R23NP
M61.2LSW-P R23SP R72NP
M61.2LNW-P R72SP R73NP
R73SP
MK15… MK18… MK20…
Connecting Pin Size
Selection Chart Connecting Pin Size
Fastener Type
Co
nn
ect
ing
P
in T
ype
Ab
bre
via
tio
n
Pin
Wear
F
acto
r
Faste
ner
Wear
F
acto
r
Ru
st
R
esis
tan
ce
Ch
em
ical
Resis
tan
ce
Mag
neti
sm
Rig
idit
y
Fle
xib
ilit
y
Vary
ing
Belt
T
en
sio
n,
S
mall B
elt
s
Nylosteel
Nylon coated music wire
Nylostainless
Nylon coated 316SS-solid wire
Smooth solid Nylon
Solid Nylon notched
Smooth 316SS-solid wire
316SS-solid wire notched
Nylocable
Nylon coated zinc plated cable
Nylocable Stainless
Nylon coated 316SS cable
Excellent
Very Good Good
Good
Solid Nylon
...NY
...NYN
Stainless Steel Wire
...WSS
...WSSN
Excellent Very GoodSlightly
MagneticGood
Excellent Good Good
Good
Excellent
Not Applicable
Magnetic Good Very Good
Acceptable
Very Good Good
Excellent Excellent Excellent ExcellentNon
MagneticAcceptable Excellent
Excellent Very GoodSlightly
MagneticVery Good
...NC
...NSS
Very Good Very GoodSlightly
MagneticExcellent
Excellent
...NCS
Excellent Excellent
Excellent Excellent
Acceptable Good
Excellent Excellent
...NST
Selection Chart Connecting Pin Type
Very Good GoodAcceptable AcceptableHigh
MagneticVery Good
Description Belt Width Length Pins Order No kg mm mm per PU
Connecting Pin MK15-NYN, Cut to LengthSolid Nylon Notched
A functioning Lacing Tool consists of a MATOHYD 200W, MATOHYDVICE 200W, an appropriate Fastener Retainer UNICOMB and either an Electro-Hydraulic Power Unit MATOHYD PAW or a Foot Pump FP.
with according length and pitch.
Page 17
Lacing Tools and Accessoriesfor the Laundry Industry
Routinely, a UNICOMB 300…VH is used in our MATOHYDVICE 200W with according fastener pitch.
To install fasteners with a Vice Lacer, you need a Fastener Retainer for every basic tool MATOVICE
Fastener Retainer UNICOMB V
MATOHYD FP
Eco-Vice Lacer MA
MATOHYD FP
Description Working Width Pitch Order No kg(mm)
Special Lacing Tools
MATOLEVER 60 mm 2,54 42 480 86 60 2,5
Plier Lacer MZ60 50 mm 2,54 42 050 61 63 1,6
MATOLEVER
Special Accessories
Textile Belt Cutter 50mm / 90deg 50 mm 42 050 10 10 0,4
Spare Blades for Textile Belt Cutter PU10 42 050 10 11 0,01
Belt Cutter LD 150 150 mm 42 510 01 50 2,4
Spare Blades for Belt Cutter LD 42 510 11 50 0,01
Belt Clamp W-1 100 mm 42 480 90 00 1,1 Textile Belt CutterTape Binder for Textile Belts (300 g) 42 232 02 00 0,4
Supergrip Skiver 7 mm 42 640 00 00 0,1
Belt Cutter LD 150 Belt Clamp W-1
Supergrip Skiver
Page 18
Lacing Tools and Accessoriesfor the Laundry Industry
Tape Binder for Textile Belts
Plier Lacer MZ60
Page 19
General Conditions Of Sales, Supply And Payment
I. Quotation The documentation pertaining to the quotation such as illustrations, drawings, details of weights and dimensions are only approximately authoritative where they are not expressly designated asbinding. The supplier retains the right to ownership and Copyright of all cost estimates, drawings and other papers. These must not be made accessible to third parties The supplier has anobligation not to make accessible to third parties any plans designated as confidential by the purchaser, without the latter's approval. II. Scope of the delivery The written order confirmation from the supplier is definitive for the scope of the delivery. In the case of a quotation from the supplier with a time commitment and timely acceptance, the quotation is definitive, where there is no confirmation of the Order in good time. Supplementary agreements and changes require the written confirmation of the supplier III. Price and payment 1. In the absence of any special agreements the prices are ex works, including loading at the factory, but excluding packing. VAT at the applicable statutory rate must be added to the prices, 2. In the absence of any special agreement payment is to be made in cash with no deductions and free of charge at the supplier's point of payment i.e.: 1/3 down payment on receipt of the order
confirmation 1/3 when the purchaser is informed that the major components are ready for despatch the remainder within one month of this. 3. The withholding of payments or the offsetting of any counter claims by the purchaser which are disputed by supplier are not permitted. IV. Delivery time 1. The delivery time begins with the sending of the order confirmation but not before the purchaser furnishes the documents, approvals, clearances to be provided and also the arrival of the agreed
down payment. 2. The delivery times will be extended commensurately in the event of actions which form part of labour disputes, especially strikes and lockouts and also in the event of any unforeseen impediments
which are outside the control of the supplier where such impediments can be shown to have a considerable influence of the manufacture or shipment of the object being supplied. This also applies when these circumstances occur at sub-suppliers. The circumstances described are also not to be blamed by the supplier when they arise during an already existing delay. In important cases the supplier will notify the purchaser of the beginning and end of such impediments as soon as possible.
3. The delivery times has been adhered to if by the time it expires the object being supplied has left the factory or its readiness for despatch has been notified. 4. When damage is suffered by the purchaser as a result of delay which has occurred due to the supplier, the purchaser is entitled to request compensation for the delay, to the exclusion of further
claims. For each full week of lateness this will amount to 1/2 of 1%, but at the most 5% of the value of that part of the total delivery which as a result of the delay cannot be utilised in good time or in accordance with the contract.
5. If despatch is delayed at the wish of the purchaser he will be charged for the cost of storage beginning one month after indication of readiness for despatch, for storage at the supplier's factory however at least 1/2 of 1% of the invoiced amount for each month. The supplier however is entitled after setting a suitable period and its fruitless expiry to make other use of the object being supplied and to supply the purchaser over a suitable extended period.
6. Adherence to the delivery period assumes the purchaser meets his contractual obligations. V. Transfer of risk and acceptance 1. The risk is transferred to the purchaser at the latest upon despatch of the supplied parts, i.e. even if partial deliveries are made or the supplier has taken on further services such as the costs
of despatch or transport and setting up. At the request of the purchaser, and at his expense, the shipment can be insured against theft, breakage, transport, fire and water damage and other insurable risks.
2. If the despatch is delayed as a result of circumstances which are the fault of the purchaser, then the risk Is transferred to the purchaser from the day of readiness for despatch; the supplier is however under an obligation, at the wish and expense of the purchaser, to effect insurance which the latter request.
3. Objects supplied, even if they exhibit insignificant defects, are to be accepted by the purchaser regardless of the rights under section VII. 4. Partial deliveries are permissible. VI. Right of ownership 1. The supplier retains the right of ownership to objects supplied until the arrival of all payments under the contract to supply. 2. The supplier is entitled to insure the object supplied against theft, breakage, transport, fire and water damage and other damage at the purchaser's expense when the purchaser has not
shown that he has taken out hat insurance himself. 3. The purchaser can neither pawn the object supplied nor transfer ownership of it as security. In the event of distrait or other possession by a third party he must inform the supplier without
delay 4. If the purchaser behaves in a manner contrary to the contract, particularly by delaying payment, the supplier is entitled to take back the goods after warning and the purchaser is obliged to
VII. Liability for defects in the delivery For defects in the delivery, which includes the absence of the properties explicitly promised, the supplier has the following obligations, to the exclusion of further claims regardless of section IX, 4. 1. All parts which within six month of commissioning prove to be unusable or whose usability is significantly impaired as a result of a state of affairs which was present before the transfer of risk,
particularly due to faulty construction, poor material or bad workmanship will be repaired or supplied new at the choice of the supplier, as he judges best. The discovery of such defects is to bereported to the supplier in writing without delay. Replaced parts become the property of the supplier. If despatch, set up or commissioning is delayed, without blame being attached to the supplier then this liability expires at the latest 12 month after the transfer of risk. For essential third party products the supplier's liability is limited to the transfer of the entitlement to liability which exists vis a vis the sup-supplier of the third party product.
2. The right of the purchaser to assert claims due to defects expires in all cases in 6 months from the time of the punctually made complaint, or upon the expiry of the warranty period. 3. No warranty is taken on for damage which occurs due to the following reasons; unsuitable or improper use, incorrect fitting or incorrect repair by the purchaser of by a third party, natural wear
and tear, incorrect or negligent treatment, unsuitable operating materials, replacement materials defective construction work, unsuitable construction site, chemical, electro-chemical or electrical effects for which the blame cannot be attributed to the supplier.
4. To allow the repairs and the supply of replacements to be carried out, which appear necessary in the best judgment of the supplier the purchaser, after agreement with the supplier, must provide the necessary time and opportunity otherwise the supplier is released from his obligation for the defect. Only in urgent cases where operational safety is a risk or to avoid disproportionately large damage, whereupon the supplier must be made aware immediately, or if the supplier is delayed in eliminating the defect, the purchaser has the right to eliminate the defect himself or have it eliminated by a third party and to demand reimbursement of the necessary costs from the supplier.
5. Of the direct costs in cured by the repairs of the supply of replacements the supplier will - insofar as the complaint is shown to be justified- bear the cost of the replacement items including the despatch, plus the reasonable costs for the removal and fitting and furthermore, where this can be rightly requested depending on the situation of the individual case, any necessary costs for providing his mechanics and assistants. The purchaser generally bears all other cost.
6. The warranty period on the replacement items and the repair is three months, but this will run until the time of the expiry of the original warranty period for the object supplied. If repairs are necessary the period of liability for the object supplied will be extended by the length of the interruption in operation caused by this.
7. Any modifications or repair work carried out on the part of the purchaser or a third party either inexpertly or without the prior approval of the supplier will cancel the liability for the consequences such actions.
8. Further claims by the purchaser, especially claims for damage which did not occur on the supplied object itself are excluded. The exclusion of liability does not apply if the owner or leading the owner or leading employee, the supplier is only liable for sensibly foreseeable damage typical of the contract. The exclusion of liability also does not apply in cases where in accordance with the product liability law liability is accepted for damage to persons or property on privately used objects, where faults exist on the object supplied. It also does not apply when properties.
VIII. Liability for associated obligation When, through the fault of the supplier, the object supplied cannot be used by the purchaser in accordance with the contract as a result of omitted or incorrect implementation of suggestions or advice which occurred before or after conclusion of the contract and also other obligations related to the contract, especially instructions for the operation and maintenance of the object supplied thenthe rulings in Section VII and IX apply appropriately, to the exclusion of further claims by the purchaser. IX. The rights of the purchaser to withdrawal, variation and other liability of the supplier 1. The purchaser can also withdraw from the contract is the whole provision of supplies and/or services becomes completely impossible for the supplier before the transfer of risk. The same applies
in the event of the supplier’s inability to deliver. The purchaser can also withdraw from the contract, for an order of objects of the same type, the implementation of a part of the delivery becomesimpossible with respect to quantity or he has a justified interest in refusing a partial delivery, if this is not the case the purchaser can reduce the counter payment to suit.
2. If a delivery delay exists as defined under Section IV of the Conditions of Supply and if the purchaser grants the supplier who is in arrears with the delivery a suitable extension period with an explicit declaration that after the expiry of this period he will refuse to accept the goods and/or services, and it this extended deadline is not met, then the purchaser is entitled to withdraw.
3. If the impossibility occurs during the delay in acceptance or due to the fault of the purchaser then the purchaser remains obliged to make the counter payment. 4. The purchaser also has the right to cancellation of the contract if the supplier, through his own fault, allows a suitable extension period granted to him for repairs of the supply of replacements
with regard to a defect, as defined in the conditions of supply and attributable to him, to expire fruitlessly. The right of the purchaser to cancellation of the contract also exists in other cases of failure of the supplier to repair or supply a replacement.
5. Further claims by the purchaser are excluded, especially to termination or reduction and also to compensation for damages of any kind i.e. also for any damages which did not occur on the supplied object itself. This exclusion of liability does not apply if the owner or leading employee have acted with intent or gross negligence and also if there has been blameworthy violation of essential obligations under the contract. In the event of blameworthy violations of essential obligations under the contract, except in cases of intent or gross negligence by the owner of leading employee, the supplier is only liable for sensibly foreseeable damage typical of the contract. The exclusion of liability also does not apply in cases where In accordance with the product liabilitylaw liability is accepted for damage to persons or property on privately used objects, where faults exist on the object supplied. It also does not apply when properties are absent which were expressly promised when the promise had the intention of covering the purchaser against damage which did not arise on the supplied object itself.
X. Court of jurisdiction If the purchaser is a fully qualified merchant, a legal personage in public law or a legally separate property proceedings for all disputes arising from a contractual relationship are to be taken at the court with jurisdiction for the supplier's head office or the branch of the supplier which made the delivery. The supplier is also entitled lo take proceedings against the buyer at the court of jurisdiction for his head office.
MATO Maschinen- und Metallwarenfabrik Curt Matthaei GmbH & Co. KG
Page 20
General Remarks
Availability and Delivery TimeIn order to provide the soonest possible delivery service, most of the products are available from stock. The delivery time for non- stock items will be advised.
Product LiabilityAll our items are checked according to the Product Liability Law dated 01.01.1990. However, we emphasise that the use of non-original MATO parts may lead to loss of insurance protection. Furthermore any use of products other than originally inteded has to be excluded. The operation instructions of our tools/ machines as well as the hints on hazards have to be observed carefully.
Minimum Order ValuePlease note that any order treatment involves costs wich are extremly high for small quanitites. Therefore, for order remaining under 50,00 EUR net, we have to charge a 10,00 EUR fee in order to cover the treatment costs.
Price ValidityThe price validity will loose effectiveness in case of extraordinary price changes in the raw material sector. With this Price List all other price lists will loose their vailidity.The prices stated in this list are gross prices to which legal VAT has to be added.
Changes
Due to the product development, we reserve the right to change pictures or accessories.
Please observe our Conditions of Sale, Delivery and Payment.
We connect anything!Please ask for more information about the
Belt Lacing Systems for low tensile conveyor belts up to 750 kN/mand/or
Belt Lacing Systems for high tensile conveyor belts above 750 kN/m