manual spacemaker radio.pdf

8/11/2019 manual spacemaker radio.pdf

1/12

u s e r m a n u a l

7-5400

EN/E It is important to read this instruction book prior to

using your new product for the first time. Es importante leer este manual antes de usar por vez

primera su euipo.

manual de usuario

EXPORTERThomson Inc.

P.O. Box 1976Indianapolis, IN 46206-1976

2006 Thomson Inc.Trademark(s) Registered

Marque(s) Depose(s)Marca(s) Registrada(s)

5639 2420 (EN/E)www.ge-electronics.com

Printed In China


2/12


3/12


4/12

EN EN

4

Note:

If your cabinet has glue blocks orother obstructions, cut out correspondingareas on the Template to clear them. Do notcut out or cut through the screw holesindicated on the Template.

Note:

It is recommended that safetyglasses be worn while drilling screw holes toprevent the possibility of eye injury.

2. Drill1 / 4 -inch diameter holes through theunderside of the cabinet bottom shelf usingthe 3 points marked on the Template.

Tips:

On wooden cabinets you may want to markand start the drill holes with a nail or anawl.Be sure to hold the drill very firmly againstthe cabinet to reduce walking of the drillbit from the markings.Use masking tape above the hole locationson inside of wooden cabinet shelf to helpreduce splintering.If installing the unit under a wood cabinet,you may wish to countersink the drilled holefrom the INSIDE of the cabinet if acountersink attachment for your drill isavailable. This will eliminate the use ofwashers and allow the screw heads to beflush with the floor of your cabinet. If youcannot countersink the holes, use thesupplied washers.

3. Remove Template and clean drill shavingsfrom inside and underside of cabinet.

4. If your cabinet does not have anoverhang , go to Step 5.If your cabinet has an overhang, selectthe spacer or combination of spacers that isequal to or longer than the cabinet overhang.

First Things First

3

Mounting Procedure1. If your cabinet does not have an

overhang:(a) Position Template in desired location on

underside of cabinet, flush with frontedge.

(b) Then tape Template in place, and go toStep 2.

MEASURE THICKNESS OFCABINET OVERHANG

FRONT EDGEOF CABINET

MOUNTINGTEMPLATE

If your cabinet has an overhang:(a) Measure the thickness of the overhang.(b) Fold front of Template downward along

the printed guideline that is closest tothe thickness of your cabinet.

(c) Tape fold-down portion to backside ofoverhang, Tape Template to cabinetunderside.

FOLD TEMPLATE ONDOTTED LINE


5/12


6/12

EN EN

Installing Back up Battery:1. The compartment door is located at the side

of the Spacemaker.

Rotate the lock in the direction of theicon until it is released. Remove thecompartment door.

2. Before inserting the batteries, observe thepolarities (that is, + and -) of the batteries,

then relate the polarities to the engraveddiagram inside the battery compartment.Now insert the batteries.

3. Replace the battery compartment door. Lockthe door in place by pushing down on thelock and rotating it in the opposite direction(counterclockwise).

This clock radio is equipped with a memoryholding system that can be powered with 2AAA batteries (included and installed). Thepower failure protection circuit will not operateunless battery is installed.When normal household power is interrupted, orAC line cord is unplugged, the batteries willpower the Spacemaker to keep track of time andtimer setting programmed into memory. Whenthe battery backup functions, the digital displaywill not light. Normal operation will resumeafter AC power is restored so you will not haveto reset the time.

Power Failure IndicatorThe display blinks when AC power is interruptedfor more than 2 seconds. You need to reset theclock time to stop the display from blink.

Battery Backup Operation

Note:

It is advised that the batteries bereplaced every 3 years.

8

Getting Started

Canadian Time Zone (Figure 2)

U.S. Time Zone (Figure 1)

7


7/12


8/12


9/12


10/12


11/12


12/12

manual spacemaker radio.pdf

Documents