Manual de Servicio Para MP 6500 SM_5500_6500_7500

8/13/2019 Manual de Servicio Para MP 6500 SM_5500_6500_7500

1/868

MODEL MT-C1(Machine Code: B064/B065

MODEL MT-C2B140/B141/B163/B142/B143/B228

MODEL MT-C3B246/B248/B249/B250/B252/B253

SERVICE MANUAL

June 2006Subject to Change


2/868

IMPORTANT SAFETY NOTICES

PREVENTION OF PHYSICAL INJURY

1. Before disassembling or assembling parts of the copier and peripherals,make sure that the copier power cord is unplugged.

2. The wall outlet should be near the copier and easily accessible.

3. Note that some components of the copier and the paper tray unit aresupplied with electrical voltage even if the main power switch is turned off.

4. If any adjustment or operation check has to be made with exterior covers offor open while the main switch is turned on, keep hands away from electrifiedor mechanically driven components.

5. If the Start key is pressed before the copier completes the warm-up period(the Start key starts blinking red and green alternatively), keep hands awayfrom the mechanical and the electrical components as the copier startsmaking copies as soon as the warm-up period is completed.

6. The inside and the metal parts of the fusing unit become extremely hot whilethe copier is operating. Be careful to avoid touching those components withyour bare hands.

HEALTH SAFETY CONDITIONS

1. Never operate the copier without the ozone filters installed.

2. Always replace the ozone filters with the specified ones at the specifiedintervals.

3. Toner and developer are non-toxic, but if you get either of them in your eyesby accident, it may cause temporary eye discomfort. Try to remove with eyedrops or flush with water as first aid. If unsuccessful, get medical attention.

OBSERVANCE OF ELECTRICAL SAFETY STANDARDS

1. The copier and its peripherals must be installed and maintained by acustomer service representative who has completed the training course onthose models.

2. The NVRAM on the system control board has a lithium battery which canexplode if replaced incorrectly. Replace the NVRAM only with an identicalone. The manufacturer recommends replacing the entire NVRAM. Do notrecharge or burn this battery. Used NVRAM must be handled in accordancewith local regulations.


3/868

SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL

1. Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly

when exposed to an open flame.2. Dispose of used toner, developer, and organic photoconductors in

accordance with local regulations. (These are non-toxic supplies.)

3. Dispose of replaced parts in accordance with local regulations.

4. When keeping used lithium batteries in order to dispose of them later, do notput more than 100 batteries per sealed box. Storing larger numbers or notsealing them apart may lead to chemical reactions and heat build-up.

LASER SAFETY The Center for Devices and Radiological Health (CDRH) prohibits the repair oflaser-based optical units in the field. The optical housing unit can only be repairedin a factory or at a location with the requisite equipment. The laser subsystem isreplaceable in the field by a qualified Customer Engineer. The laser chassis is notrepairable in the field. Customer engineers are therefore directed to return allchassis and laser subsystems to the factory or service depot when replacement ofthe optical subsystem is required.

WARNING

Use of controls, or adjustment, or performance of procedures other thanthose specified in this manual may result in hazardous radiation exposure.

WARNING WARNING: Turn off the main switch before attempting any of the

procedures in the Laser Unit section. Laser beams canseriously damage your eyes.

CAUTION MARKING:


4/868


5/868

i

TABLE OF CONTENTS

1. INSTALLATION .......................................................................................................................... 1-1

1.1 INSTALLATION REQUIREMENTS ..................................................................................... 1-11.1.1 OPERATING ENVIRONMENT.................................................................................. 1-11.1.2 MACHINE LEVEL ...................................................................................................... 1-21.1.3 MINIMUM SPACE REQUIREMENTS ....................................................................... 1-31.1.4 DIMENSIONS ............................................................................................................ 1-4

B064 Series................................................................................................................... 1-4B140 Series................................................................................................................... 1-5B246 Series................................................................................................................... 1-6

1.1.5 PERIPHERAL/OPTION SUMMARY TABLE ............................................................. 1-71.1.6 POWER REQUIREMENTS ....................................................................................... 1-9

1.2 MAIN MACHINE (B064 SERIES/B140 SERIES/B246 SERIES)....................................... 1-101.2.1 ACCESSORY CHECK............................................................................................. 1-101.2.2 INSTALLATION PROCEDURE ............................................................................... 1-11

Removing Tapes and Retainers ................................................................................. 1-11Connecting the ADF.................................................................................................... 1-14Removing and Filling the Development Unit............................................................... 1-14Re-installing the Development Unit ............................................................................ 1-17Initializing the Drum Settings (B064 Series) ............................................................... 1-18Initializing the Drum Settings (B140/B246 Series)...................................................... 1-19Tandem Tray............................................................................................................... 1-20Machine Level............................................................................................................. 1-22Date/Time Setting ....................................................................................................... 1-22SP Codes.................................................................................................................... 1-22

1.3 A3/DLT FEEDER KIT (B475)............................................................................................. 1-231.3.1 ACCESSORY CHECK............................................................................................. 1-231.3.2 INSTALLATION PROCEDURE ............................................................................... 1-24

1.4 LCT (B473)......................................................................................................................... 1-261.4.1 ACCESSORY CHECK............................................................................................. 1-261.4.2 INSTALLATION PROCEDURE ............................................................................... 1-27

Removing Tape........................................................................................................... 1-27Preparing the Main Machine....................................................................................... 1-28Installing the LCT........................................................................................................ 1-28

1.5 LG/B4 FEEDER KIT (B474)............................................................................................... 1-311.5.1 ACCESSORY CHECK............................................................................................. 1-311.5.2 INSTALLATION PROCEDURE ............................................................................... 1-32

1.6 3000-SHEET FINISHERS (B468/B469/B674)................................................................... 1-351.6.1 ACCESSORY CHECK............................................................................................. 1-351.6.2 INSTALLATION PROCEDURE ............................................................................... 1-36

Removing Tapes and Retainers ................................................................................. 1-36

Installation................................................................................................................... 1-38Selecting the Staple Supply Name ............................................................................. 1-41Enabling Booklet Binding............................................................................................ 1-41

1.7 PUNCH UNIT (B377) ......................................................................................................... 1-421.7.1 ACCESSORY CHECK............................................................................................. 1-421.7.2 INSTALLATION PROCEDURE ............................................................................... 1-43


6/868

ii

1.8 COVER INTERPOSER TRAY (B470) ............................................................................... 1-451.8.1 ACCESSORY CHECK............................................................................................. 1-451.8.2 INSTALLATION PROCEDURE ............................................................................... 1-46

Removing Tapes and Retainers ................................................................................. 1-46 Attaching the Extensions ............................................................................................ 1-48

Attaching the Interposer Tray...................................................................................... 1-49 Attaching the Corner Plates for the B478/B706.......................................................... 1-50Right Rear Corner Plate (B478/B706 only)................................................................. 1-50Right Front Corner Plate (B478/B706 only)................................................................ 1-51

Attaching the Finisher to the Machine ........................................................................ 1-521.9 9-BIN MAILBOX (B471) ..................................................................................................... 1-54

1.9.1 ACCESSORY CHECK............................................................................................. 1-541.9.2 INSTALLATION PROCEDURE ............................................................................... 1-55

Removing Tapes and Retainers ................................................................................. 1-55Installation................................................................................................................... 1-56

1.10 3000 SHEET FINISHER (B478/B706) ............................................................................. 1-581.10.1 ACCESSORY CHECK........................................................................................... 1-581.10.2 INSTALLATION ..................................................................................................... 1-59

1.11 PUNCH UNIT (B531/B812).............................................................................................. 1-631.11.1 ACCESSORY CHECK........................................................................................... 1-631.11.2 INSTALLATION ..................................................................................................... 1-64

1.12 JOGGER UNIT (B513)..................................................................................................... 1-681.12.1 ACCESSORY CHECK........................................................................................... 1-681.12.2 INSTALLATION PROCEDURE ............................................................................. 1-69

1.13 Z-FOLDING UNIT (B660)................................................................................................. 1-701.13.1 ACCESSORY CHECK........................................................................................... 1-701.13.2 INSTALLATION PROCEDURE ............................................................................. 1-71

Before You Begin........................................................................................................ 1-71Unpacking ................................................................................................................... 1-72Docking to the Finisher ............................................................................................... 1-73Docking to the Main Frame......................................................................................... 1-76

1.14 2000/3000 SHEET FINISHERS (B700/B701) ................................................................. 1-781.14.1 ACCESSORIES..................................................................................................... 1-781.14.2 INSTALLATION PROCEDURE ............................................................................. 1-79

Removing Tapes and Retainers ................................................................................. 1-79Docking the Finisher ................................................................................................... 1-82

Attaching the Trays ..................................................................................................... 1-85Leveling the Finisher................................................................................................... 1-86Selecting the Staple Supply Name ............................................................................. 1-87Enabling Booklet Binding (B700 Only)........................................................................ 1-87

Auxiliary Trays............................................................................................................. 1-881.15 PUNCH UNIT (B702) ....................................................................................................... 1-90

1.15.1 ACCESSORIES..................................................................................................... 1-901.15.2 INSTALLATION PROCEDURE ............................................................................. 1-91

1.16 COVER INTERPOSER TRAY (B704) ............................................................................. 1-941.16.1 ACCESSORIES..................................................................................................... 1-941.16.2 INSTALLATION PROCEDURE ............................................................................. 1-95

Removing Tapes and Retainers ................................................................................. 1-95Preparing the Finisher (B700/B701/B706).................................................................. 1-96

Attaching the Extensions for the B706........................................................................ 1-97Prepare the Cover Interposer for the B706................................................................. 1-98

Attach the Extensions to the B706.............................................................................. 1-99 Attaching the Extensions for the B700/B701 ............................................................ 1-100 Attaching the Interposer Tray (B700/B701/ B706).................................................... 1-101 Attaching the Corner Plates for the B706................................................................. 1-102Docking the Finisher and Interposer to the Machine (B700/B701/B706) ................. 1-104


7/868

iii

1.17 OUTPUT JOGGER UNIT (B703)................................................................................... 1-1061.17.1 ACCESSORIES................................................................................................... 1-1061.17.2 INSTALLATION PROCEDURE ........................................................................... 1-107

1.18 MAIL BOX (B762) .......................................................................................................... 1-1091.18.1 ACCESSORY CHECK......................................................................................... 1-109

1.18.2 INSTALLATION PROCEDURE ........................................................................... 1-1101.19 COPY TRAY (B756)....................................................................................................... 1-1131.19.1 ACCESSORIES................................................................................................... 1-1131.19.2 INSTALLATION ................................................................................................... 1-114

1.20 KEY CARD BRACKET (B498), KEY COUNTER BRACKET (B452)............................. 1-1171.20.1 KEY CARD BRACKET B498 ACCESSORIES.................................................... 1-1171.20.2 KEY COUNTER BRACKET B452 ACCESSORIES ............................................ 1-1181.20.3 INSTALLATION ................................................................................................... 1-119

Assemble the Key Counter Bracket.......................................................................... 1-119Install the Key Card Bracket and Assembled Key Counter ...................................... 1-120

1.21 COPY CONNECTOR KITS............................................................................................ 1-1221.21.1 COPY CONNECTOR KIT (B525-10, -12) FOR B064 SERIES ........................... 1-122

ACCESSORY CHECK.............................................................................................. 1-123

Installation................................................................................................................. 1-124Installing the Hardware ............................................................................................. 1-1251.21.2 COPY CONNECTOR KIT (B328-03) FOR B140 SERIES .................................. 1-129

ACCESSORY CHECK.............................................................................................. 1-129Preparation................................................................................................................ 1-130Installation................................................................................................................. 1-131

1.21.3 COPY CONNECTOR (B842) FOR B246 SERIES .............................................. 1-134 Accessories............................................................................................................... 1-134Preparation................................................................................................................ 1-135Installation................................................................................................................. 1-136

1.22 MFP OPTIONS: B064 SERIES...................................................................................... 1-1391.22.1 PRINTER/SCANNER KIT (G338), PRINTER KIT (G339)................................... 1-139

ACCESSORY CHECK.............................................................................................. 1-139

1.22.2 INSTALLATION PROCEDURE ........................................................................... 1-140Inserting DIMMs........................................................................................................ 1-140Installation Procedure ............................................................................................... 1-141

1.22.3 PS3 (B525-08) ..................................................................................................... 1-1431.22.4 USB 2.0 (B525-01)............................................................................................... 1-144

ACCESSORY CHECK.............................................................................................. 1-144Installation Procedure ............................................................................................... 1-144USB SP Settings....................................................................................................... 1-145

1.22.5 IEEE1394 (G561) FIREWIRE INTERFACE ........................................................ 1-146 ACCESSORY CHECK.............................................................................................. 1-146Installation Procedure ............................................................................................... 1-147UP Mode Settings for IEEE 1394 ............................................................................. 1-148SP Mode Settings for IEEE 1394.............................................................................. 1-149

1.22.6 IEEE802.11B WIRELESS LAN (G628) ............................................................... 1-150 ACCESSORY CHECK.............................................................................................. 1-150Installation Procedure ............................................................................................... 1-151UP Mode Settings for Wireless LAN......................................................................... 1-152

SP MODE SETTINGS FOR 802.11B WIRELESS LAN.......................................................... 1-1541.22.7 FILE FORMAT CONVERTER (MLB) (B519)....................................................... 1-155

Accessory Check ...................................................................................................... 1-156Installation Procedure ............................................................................................... 1-156Installing the Firmware.............................................................................................. 1-156Installing the Hardware ............................................................................................. 1-157


8/868

iv

1.23 MFP OPTIONS: B140 SERIES...................................................................................... 1-1581.23.1 MERGING APPLICATIONS ON ONE SD CARD................................................ 1-158

Overview ................................................................................................................... 1-158Merging Applications................................................................................................. 1-159Undo Exec................................................................................................................. 1-160

1.23.2 OVERVIEW.......................................................................................................... 1-1611.23.3 PRINTER/SCANNER KIT (B659)........................................................................ 1-162 ACCESSORY CHECK.............................................................................................. 1-162Installation................................................................................................................. 1-163

1.23.4 PS3 (B525-15) ..................................................................................................... 1-166 ACCESSORY CHECK.............................................................................................. 1-166Installation................................................................................................................. 1-166

1.23.5 USB 2.0 INTERFACE BOARD (B596-01) ........................................................... 1-167 ACCESSORY CHECK.............................................................................................. 1-167Installation................................................................................................................. 1-167

1.23.6 IEEE 1394 INTERFACE BOARD (B581-01) ....................................................... 1-168 ACCESSORY CHECK.............................................................................................. 1-168Installation................................................................................................................. 1-168

1.23.7 IEEE 802.11B INTERFACE BOARD (B582-01, -02)........................................... 1-169 ACCESSORY CHECK.............................................................................................. 1-169Installation................................................................................................................. 1-169

1.23.8 BLUETOOTH INTERFACE UNIT (G377)............................................................ 1-171 ACCESSORY CHECK.............................................................................................. 1-171Installation................................................................................................................. 1-171

1.23.9 FILE FORMAT CONVERTER (B609).................................................................. 1-172 ACCESSORY CHECK.............................................................................................. 1-172Installation................................................................................................................. 1-172

1.23.10 DATA OVERWRITE SECURITY UNIT (B735).................................................. 1-173 ACCESSORY CHECK.............................................................................................. 1-173Before You Begin.................................................................................................. 1-173Seal Check And Removal ......................................................................................... 1-174

Installation Procedure ............................................................................................... 1-1751.24 MFP OPTIONS: B246 SERIES...................................................................................... 1-1781.24.1 OVERVIEW.......................................................................................................... 1-1781.24.2 COMMON PROCEDURES.................................................................................. 1-179

Inserting SD Cards.................................................................................................... 1-179Storing Copied SD Cards.......................................................................................... 1-179

1.24.3 PRINTER SCANNER KIT (B841)........................................................................ 1-180 ACCESSORY CHECK.............................................................................................. 1-180Installation................................................................................................................. 1-181

1.24.4 POSTSCRIPT3 (B525)........................................................................................ 1-184 Accessories............................................................................................................... 1-184Installation................................................................................................................. 1-184

1.24.5 IEEE1394 INTERFACE BOARD (B581).............................................................. 1-185

Accessories............................................................................................................... 1-185Installation................................................................................................................. 1-185

1.24.6 WIRELESS LAN G813 (802.11B)........................................................................ 1-186 Accessories............................................................................................................... 1-186Installation................................................................................................................. 1-186

1.24.7 BLUETOOTH INTERFACE UNIT TYPE C B826 ................................................ 1-187 Accessories............................................................................................................... 1-187Installation................................................................................................................. 1-187

1.24.8 FILE FORMAT CONVERTER TYPE C B609...................................................... 1-188 ACCESSORY CHECK.............................................................................................. 1-188Installation................................................................................................................. 1-188


9/868


10/868


11/868

vii

3.6.8 DRUM POTENTIAL SENSOR................................................................................. 3-403.6.9 CLEANING FILTER................................................................................................. 3-413.6.10 CLEANING BLADE................................................................................................ 3-413.6.11 CLEANING BRUSH............................................................................................... 3-423.6.12 PICK-OFF PAWLS................................................................................................. 3-43

3.6.13 ID SENSOR ........................................................................................................... 3-433.6.14 DRUM MOTOR...................................................................................................... 3-443.6.15 TONER COLLECTION BOTTLE ........................................................................... 3-453.6.16 TONER SEPARATION UNIT................................................................................. 3-453.6.17 OZONE FILTERS .................................................................................................. 3-463.6.18 OPTICS DUST FILTER ......................................................................................... 3-463.6.19 INTERNAL DUST FILTER..................................................................................... 3-46

3.7 DEVELOPMENT UNIT....................................................................................................... 3-473.7.1 DEVELOPER REPLACEMENT............................................................................... 3-473.7.2 DEVELOPMENT FILTER ........................................................................................ 3-493.7.3 ENTRANCE SEAL AND SIDE SEALS .................................................................... 3-503.7.4 TD SENSOR............................................................................................................ 3-513.7.5 TONER END SENSOR............................................................................................ 3-51

3.7.6 TONER SUPPLY MOTOR....................................................................................... 3-523.7.7 DEVELOPMENT MOTOR ....................................................................................... 3-533.8 TRANSFER BELT UNIT .................................................................................................... 3-54

3.8.1 TRANSFER BELT UNIT .......................................................................................... 3-543.8.2 TRANSFER BELT.................................................................................................... 3-553.8.3 TRANSFER ROLLER CLEANING BLADE.............................................................. 3-573.8.4 DISCHARGE PLATE ............................................................................................... 3-583.8.5 TRANSFER POWER PACK .................................................................................... 3-59

3.9 FUSING UNIT .................................................................................................................... 3-603.9.1 FUSING UNIT .......................................................................................................... 3-603.9.2 FUSING PRESSURE RELEASE MOTOR (B140/B246 SERIES)........................... 3-623.9.3 FUSING PRESSURE RELEASE HP SENSOR (B140/B246 SERIES)................... 3-633.9.4 FUSING UNIT THERMISTORS AND THERMOSTATS.......................................... 3-64

B064 Series................................................................................................................. 3-65B140 Series................................................................................................................. 3-65B246 Series................................................................................................................. 3-65

3.9.5 WEB CLEANING ROLLER...................................................................................... 3-67Web Unit Disassembly................................................................................................ 3-67Web Unit Assembly..................................................................................................... 3-68

3.9.6 WEB MOTOR AND WEB END SENSOR................................................................ 3-693.9.7 PRESSURE ROLLER CLEANING UNIT................................................................. 3-70

B064 Series................................................................................................................. 3-70B140/B246 Series ....................................................................................................... 3-71

3.9.8 FUSING LAMPS, HOT ROLLER, AND PRESSURE ROLLER............................... 3-72B064 Series: Fusing Lamps........................................................................................ 3-72B140/B246 Series: Fusing Lamps .............................................................................. 3-73

Important Notes about Fusing Unit Assembly (B064 Series) ..................................... 3-783.9.9 PRESSURE ROLLER.............................................................................................. 3-793.9.10 STRIPPER PAWLS ............................................................................................... 3-80

B064 Series................................................................................................................. 3-80B140/B246 Series ....................................................................................................... 3-81

3.9.11 NIP BAND WIDTH ADJUSTMENT........................................................................ 3-823.9.12 FUSING UNIT EXIT SENSOR............................................................................... 3-833.9.13 FUSING/EXIT MOTOR.......................................................................................... 3-843.9.14 FUSING EXIT AND EXIT UNIT ENTRANCE SENSORS...................................... 3-85


12/868


13/868

ix

3.13 ADF ................................................................................................................................ 3-1403.13.1 ADF COVERS...................................................................................................... 3-1403.13.2 FEED UNIT .......................................................................................................... 3-1413.13.3 FEED BELT AND PICK-UP ROLLER.................................................................. 3-1423.13.4 SEPARATION ROLLER ...................................................................................... 3-143

3.13.5 REGISTRATION SENSOR.................................................................................. 3-1443.13.6 ADF CONTROL BOARD ..................................................................................... 3-1453.13.7 ORIGINAL WIDTH, INTERVAL, AND SKEW CORRECTION SENSORS........ 3-1463.13.8 ORIGINAL LENGTH SENSORS ......................................................................... 3-1473.13.9 DF POSITION AND APS SENSOR..................................................................... 3-1483.13.10 OTHER ADF SENSORS ................................................................................... 3-1493.13.11 BOTTOM PLATE LIFT MOTOR ........................................................................ 3-1503.13.12 FEED MOTOR................................................................................................... 3-1503.13.13 EXIT MOTOR AND TRANSPORT MOTOR...................................................... 3-1513.13.14 PICK-UP ROLLER MOTOR AND HP SENSOR ............................................... 3-1523.13.15 CIS POWER SUPPLY BOARD AND CIS UNIT ................................................ 3-1533.13.16 ADF EXIT SENSOR........................................................................................... 3-154

3.14 COPY IMAGE ADJUSTMENTS: PRINTING/SCANNING............................................. 3-155

3.14.1 PRINTING............................................................................................................ 3-155Registration - Leading Edge/Side-to-Side ................................................................ 3-155Blank Margin ............................................................................................................. 3-156Registration Buckle Adjustment ................................................................................ 3-156

3.14.2 SCANNING.......................................................................................................... 3-157Registration: Platen Mode......................................................................................... 3-157Magnification............................................................................................................. 3-157

3.14.3 ADF SCANNING ADJUSTMENTS...................................................................... 3-158Vertical Black Lines................................................................................................... 3-158DIP Switch Settings (ADF Main Board) .................................................................... 3-158

ADF Skew Correction ............................................................................................... 3-1583.15 TOUCH SCREEN CALIBRATION ................................................................................. 3-160

4. TROUBLESHOOTING................................................................................................................ 4-14.1 OVERVIEW.......................................................................................................................... 4-1

4.1.1 RECOVERY METHODS............................................................................................ 4-24.1.2 IMPORTANT SP CODES.......................................................................................... 4-24.1.3 DOWNLOAD ERROR CODES.................................................................................. 4-34.1.4 JAM DETECTION...................................................................................................... 4-6

SENSOR LOCATIONS................................................................................................. 4-64.1.5 TIMING CHARTS....................................................................................................... 4-7

Feed, Transport, Feed Out: Face-up............................................................................ 4-7Transport, Inverter, Feed Out: Face-down ................................................................... 4-8Duplex Transport .......................................................................................................... 4-9

4.1.6 PROGRAM DOWNLOAD........................................................................................ 4-104.2 B064 SERIES SERVICE MODE........................................................................................ 4-11

4.2.1 B064 SERIES SERVICE CALL CONDITIONS........................................................ 4-114.2.2 B064 SERIES SC CODE DESCRIPTIONS............................................................. 4-12

SC100: Scanning System........................................................................................... 4-12SC300: Image Development System (1) .................................................................... 4-15SC400: Image Development System (2) .................................................................... 4-20SC500: Feed, Transport, Duplexing, and Fusing Systems ........................................ 4-21SC600: Data Communication ..................................................................................... 4-24SC700: Peripherals..................................................................................................... 4-26SC800: Overall System............................................................................................... 4-29SC900: Miscellaneous ................................................................................................ 4-32

4.2.3 ADDITIONAL SC CODES PRINTED IN SMC REPORT......................................... 4-34


14/868

x

4.3 B140/B246 SERIES SERVICE MODE .............................................................................. 4-374.3.1 SERVICE MODE LOCK/UNLOCK .......................................................................... 4-374.3.2 B140/B246 SERIES SERVICE CALL CONDITIONS .............................................. 4-384.3.3 B140/B246 SERIES SC CODE DESCRIPTIONS ................................................... 4-39

SC100: Scanning System........................................................................................... 4-40

SC200: Exposure........................................................................................................ 4-43SC300: Image Development System (1) .................................................................... 4-44SC400: Image Development System (2) .................................................................... 4-49SC500: Feed, Transport, Duplexing, and Fusing Systems ........................................ 4-50SC600: Data Communication ..................................................................................... 4-55SC700: Peripherals..................................................................................................... 4-57SC800: Overall System............................................................................................... 4-66SC900: Miscellaneous ................................................................................................ 4-72

4.3.4 JAM CODES............................................................................................................ 4-76Main Unit: Paper Jam Errors....................................................................................... 4-76Finisher B469 Jam Codes........................................................................................... 4-77Finisher B468/B674 Jam Codes ................................................................................. 4-77Finisher B478/B706 Jam Codes ................................................................................. 4-78

Mailbox B471 Jam Codes........................................................................................... 4-78Cover Interposer Tray B470 Jam Codes .................................................................... 4-78Z-Folding Unit B660 Jam Codes................................................................................. 4-79

4.3.5 ADDITIONAL SC CODES PRINTED IN SMC REPORT......................................... 4-804.4 OTHER PROBLEMS (B064/B140/B246 SERIES) ............................................................ 4-83

4.4.1 BLOWN FUSE CONDITIONS ................................................................................. 4-834.4.2 COMMON PROBLEMS........................................................................................... 4-834.4.3 FREQUENT PAPER JAMS ..................................................................................... 4-84

5. SERVICE TABLES ..................................................................................................................... 5-1

5.1 SERVICE PROGRAM MODE.............................................................................................. 5-15.1.1 SERVICE PROGRAM MODE OPERATION ............................................................. 5-1

Service Mode Lock/Unlock ........................................................................................... 5-1

To Enter and Exit the Service Mode ............................................................................. 5-2To Enter and Exit the Super SP Mode.......................................................................... 5-2To Switch to the Copy Window for Test Printing .......................................................... 5-2Using the SP Mode ....................................................................................................... 5-3SP Mode Button Summary ........................................................................................... 5-4SP Mode Print (SMC Print)........................................................................................... 5-5

5.2 RESETS............................................................................................................................... 5-65.2.1 MEMORY ALL CLEAR: SP5801 ............................................................................... 5-65.2.2 SOFTWARE AND SETTING RESET ...................................................................... 5-10

Software Reset ........................................................................................................... 5-10Resetting the System.................................................................................................. 5-10Resetting Copy/Document Server Features Only....................................................... 5-10Resetting Scanner Features Only............................................................................... 5-10

5.3 TEST PATTERN PRINTING.............................................................................................. 5-115.3.1 PRINTING TEST PATTERN: SP2902-003.............................................................. 5-11

Test Pattern Table ...................................................................................................... 5-125.3.2 IPU FRONT/BACK TEST PATTERNS: SP2902-001,002....................................... 5-13

Test Pattern Table ...................................................................................................... 5-145.3.3 IPU PRINTING TEST PATTERN: SP2902-004 ...................................................... 5-15


15/868

xi

5.4 SOFTWARE UPDATE ....................................................................................................... 5-165.4.1 SOFTWARE UPDATE PROCEDURE: B140/B246 SERIES................................... 5-16

Updating the LCDC for the Operation Panel .............................................................. 5-21Downloading Stamp Data ........................................................................................... 5-21NVRAM Data Upload/Download................................................................................. 5-22

5.4.2 SOFTWARE UPDATE PROCEDURE: B064 SERIES............................................ 5-23GW Controller/BCU Update........................................................................................ 5-24Forced Update ............................................................................................................ 5-25Stamp Data Update .................................................................................................... 5-25Operation Panel Software Update.............................................................................. 5-26Scanner Update .......................................................................................................... 5-27NIB Update.................................................................................................................. 5-27NetFile Firmware Update............................................................................................ 5-27NVRAM Update .......................................................................................................... 5-28Firmware Update Notes .............................................................................................. 5-28

5.5 SERVICE PROGRAM MODE TABLES............................................................................. 5-295.5.1 SERVICE TABLE KEY............................................................................................. 5-295.5.2 COPIER SERVICE TABLE...................................................................................... 5-30

SP1xxx Feed............................................................................................................... 5-30SP2xxx Drum .............................................................................................................. 5-36SP3xxx Processing..................................................................................................... 5-55SP4xxx Scanner ......................................................................................................... 5-58SP5xxx Mode.............................................................................................................. 5-68SP6xxx Peripherals................................................................................................... 5-120SP7xxx Data Logs .................................................................................................... 5-131SP8xxx: Data Log2 ................................................................................................... 5-148

5.5.3 PRINTER SERVICE TABLE.................................................................................. 5-1775.5.4 SCANNER SERVICE TABLE................................................................................ 5-178

5.6 INPUT/OUTPUT CHECK................................................................................................. 5-1905.6.1 COPIER INPUT CHECK: SP5803......................................................................... 5-1905.6.2 COPIER OUTPUT CHECK: SP5804..................................................................... 5-196

5.6.3 ADF INPUT CHECK: SP6007 ............................................................................... 5-1985.6.4 ADF OUTPUT CHECK: SP6008 ........................................................................... 5-1995.6.5 FINISHER INPUT CHECK: SP6117 (B478/B704) ............................................... 5-2005.6.6 FINISHER OUTPUT CHECK: SP6118.................................................................. 5-2025.6.7 FINISHER 1 INPUT CHECK: 6121........................................................................ 5-2035.6.8 FINISHER 1 OUTPUT CHECK: 6124.................................................................... 5-2045.6.9 FINISHER 2 INPUT CHECK: 6122........................................................................ 5-2055.6.10 FINISHER 2 OUTPUT CHECK: 6125.................................................................. 5-206

5.7 USING THE DEBUG LOG (B140/B246).......................................................................... 5-2075.7.1 SWITCHING ON AND SETTING UP SAVE DEBUG LOG ................................... 5-2075.7.2 RETRIEVING THE DEBUG LOG FROM THE HDD ............................................. 5-2105.7.3 RECORDING ERRORS MANUALLY.................................................................... 5-2115.7.4 NEW DEBUG LOG CODES .................................................................................. 5-212

SP5857-015 Copy SD Card-to-SD Card: Any Desired Key .................................... 5-212SP5857-016 Create a File on HDD to Store a Log.................................................. 5-212SP5857-017 Create a File on SD Card to Store a Log............................................ 5-212

5.8 USER TOOLS.................................................................................................................. 5-2135.8.1 OVERVIEW............................................................................................................ 5-2135.8.2 SYSTEM SETTINGS............................................................................................. 5-214

B064 Series System Settings ................................................................................... 5-214B140 Series System Settings ................................................................................... 5-216

5.8.3 COPIER/DOCUMENT SERVER FEATURES....................................................... 5-2195.8.4 INQUIRY................................................................................................................ 5-2235.8.5 COUNTER ............................................................................................................. 5-223

5.9 DIP SWITCH TABLES..................................................................................................... 5-2245.9.1 BCU (BASE ENGINE CONTROL UNIT) ............................................................... 5-224

5.9.2 CONTROLLER BOARD......................................................................................... 5-224


16/868

xii

6. DETAILED DESCRIPTIONS ...................................................................................................... 6-1

6.1 OVERVIEW.......................................................................................................................... 6-16.1.1 PAPER PATH (WITH COVER INTERPOSER TRAY) .............................................. 6-36.1.2 PAPER PATH (WITH 9-BIN MAILBOX).................................................................... 6-46.1.3 DRIVE LAYOUT......................................................................................................... 6-5

6.2 BOARD STRUCTURE......................................................................................................... 6-66.2.1 BLOCK DIAGRAM..................................................................................................... 6-66.2.2 COMPONENT DESCRIPTIONS ............................................................................... 6-7

BCU (Base Engine Control Unit)................................................................................... 6-7Controller Board............................................................................................................ 6-7MB (Mother Board) ....................................................................................................... 6-7IPU (Image Processing Unit) ........................................................................................ 6-7SBU (Sensor Board Unit).............................................................................................. 6-8PFC (Paper Feed Control)............................................................................................ 6-8SDRB (Scanner Driver Board)...................................................................................... 6-8VIB (Video Interface Board).......................................................................................... 6-8DRB (Drive Board) ........................................................................................................ 6-8CNB (Connection Board) .............................................................................................. 6-8

HDD (Hard Disk Drive).................................................................................................. 6-96.3 COPY PROCESS OVERVIEW.......................................................................................... 6-106.4 ADF .................................................................................................................................... 6-12

6.4.1 OVERVIEW.............................................................................................................. 6-126.4.2 ADF DRIVE LAYOUT .............................................................................................. 6-136.4.3 PICK-UP ROLLER LIFT .......................................................................................... 6-146.4.4 BOTTOM PLATE LIFT............................................................................................. 6-156.4.5 ORIGINAL SEPARATION ....................................................................................... 6-166.4.6 ORIGINAL TRANSPORT ........................................................................................ 6-176.4.7 ORIGINAL SKEW CORRECTION........................................................................... 6-186.4.8 ORIGINAL SIZE DETECTION................................................................................. 6-206.4.9 ADF SCANNING...................................................................................................... 6-236.4.10 JAM DETECTION.................................................................................................. 6-24

6.5 SCANNING ........................................................................................................................ 6-256.5.1 OVERVIEW.............................................................................................................. 6-256.5.2 SCANNER DRIVE ................................................................................................... 6-266.5.3 ORIGINAL SIZE DETECTION................................................................................. 6-27

Sensors....................................................................................................................... 6-27Detection Timing......................................................................................................... 6-28

6.5.4 SCANNING MAGNIFICATION ................................................................................ 6-29Book Mode.................................................................................................................. 6-29

6.5.5 AUTO IMAGE DENSITY (ADS)............................................................................... 6-30Xenon Lamp CCD ADS.......................................................................................... 6-30CIS ADS...................................................................................................................... 6-30

6.6 IMAGE PROCESSING....................................................................................................... 6-316.6.1 OVERVIEW.............................................................................................................. 6-316.6.2 IMAGE PROCESSING FLOW................................................................................. 6-326.6.3 IMAGE PROCESSING MODES.............................................................................. 6-336.6.4 IMAGE QUALITY SP ADJUSTMENTS ................................................................... 6-34

Custom Settings for Each Mode: Image Quality......................................................... 6-34Custom Settings for Each Mode: Line Width Correction ............................................ 6-36Custom Setting: Duplex Scanning Mode Original Image Quality Settings ................. 6-38Settings Adjustable for Each Original Mode ............................................................... 6-39

6.6.5 RELATION BETWEEN THE SP AND UP SETTINGS ............................................ 6-406.6.6 IMAGE PROCESSING TROUBLESHOOTING....................................................... 6-42

Removing Background from Coarse Paper................................................................ 6-42Improving the Appearance of a Copy of a Color Document ....................................... 6-42Removing Vertical White Lines During Duplex Scanning........................................... 6-43Equalizing Duplex Scanned Image Quality of Front/Back Sides ................................ 6-44Equalizing Image Quality of Front Sides for Duplex and Simplex Modes .................. 6-44


17/868

xiii

6.7 LASER EXPOSURE .......................................................................................................... 6-456.7.1 OVERVIEW.............................................................................................................. 6-456.7.2 OPTICAL PATH....................................................................................................... 6-466.7.3 FOUR-BEAM EXPOSURE ...................................................................................... 6-476.7.4 COOLING FAN ........................................................................................................ 6-48

6.7.5 LD SAFETY SWITCHES ......................................................................................... 6-49B064 Series, B140 Series Safety Switches................................................................ 6-49B246 Series Safety Switches...................................................................................... 6-50

6.8 DRUM UNIT ....................................................................................................................... 6-516.8.1 OVERVIEW.............................................................................................................. 6-516.8.2 OPC DRUM ............................................................................................................. 6-526.8.3 DRUM DRIVE .......................................................................................................... 6-526.8.4 DRUM CHARGE...................................................................................................... 6-536.8.5 CHARGE CORONA WIRE CLEANING................................................................... 6-546.8.6 DRUM PICK-OFF MECHANISM ............................................................................. 6-556.8.7 DRUM CLEANING................................................................................................... 6-566.8.8 DRUM VENTILATION AND OZONE FILTER.......................................................... 6-576.8.9 TONER RECYCLING .............................................................................................. 6-58

6.8.10 WASTE TONER COLLECTION ............................................................................ 6-59Mechanism.................................................................................................................. 6-59Error Detection............................................................................................................ 6-59

6.8.11 PROCESS CONTROL........................................................................................... 6-60What Happens at Power On ....................................................................................... 6-60Drum Potential Sensor Calibration.............................................................................. 6-61Development Bias, Bias Grid, and LD Adjustment ..................................................... 6-62ID Sensor Calibration (Vsg) ........................................................................................ 6-64TD Sensor Calibration (Vref)....................................................................................... 6-64

6.9 DEVELOPMENT AND TONER SUPPLY .......................................................................... 6-656.9.1 OVERVIEW.............................................................................................................. 6-65

Development Unit ....................................................................................................... 6-65Toner Supply............................................................................................................... 6-66

6.9.2 DEVELOPMENT UNIT ............................................................................................ 6-676.9.3 DEVELOPER/TONER MIXING (AGITATION) ........................................................ 6-686.9.4 DEVELOPMENT BIAS............................................................................................. 6-696.9.5 TONER SUPPLY ..................................................................................................... 6-706.9.6 DEVELOPMENT UNIT DRIVE AND VENTILATION............................................... 6-716.9.7 TONER END SENSOR............................................................................................ 6-726.9.8 SHUTTER MECHANISM......................................................................................... 6-726.9.9 TONER BOTTLE SUPPLY AND VENTILATION..................................................... 6-736.9.10 TONER SUPPLY CONTROL ................................................................................ 6-74

Sensor Control Mode.................................................................................................. 6-74Pixel Count Toner Supply Mode ................................................................................. 6-75TD Sensor Initialization............................................................................................... 6-76Determining Vref ......................................................................................................... 6-76

Toner Supply without ID Sensor and TD Sensors...................................................... 6-77 Abnormal TD Sensor Output....................................................................................... 6-77 Abnormal ID Sensor Output........................................................................................ 6-77Toner End Detection ................................................................................................... 6-78Toner End Recovery ................................................................................................... 6-78


18/868

xiv

6.10 IMAGE TRANSFER AND PAPER SEPARATION........................................................... 6-796.10.1 OVERVIEW............................................................................................................ 6-796.10.2 TRANSFER BELT LIFT ......................................................................................... 6-80

Mechanism.................................................................................................................. 6-80Timing ......................................................................................................................... 6-81

6.10.3 TRANSFER BELT CHARGE................................................................................. 6-826.10.4 TRANSFER CURRENT SETTINGS...................................................................... 6-836.10.5 TRANSFER CURRENT CIRCUIT ......................................................................... 6-846.10.6 TRANSFER BELT DRIVE AND PAPER TRANSPORT........................................ 6-856.10.7 TRANSFER BELT CLEANING.............................................................................. 6-866.10.8 ANTI-CONDENSATION HEATER......................................................................... 6-87

6.11 PAPER FEED .................................................................................................................. 6-886.11.1 OVERVIEW............................................................................................................ 6-88

Tray Capacities ........................................................................................................... 6-89Built-in Feed Stations.................................................................................................. 6-89By-pass Feed.............................................................................................................. 6-89Paper Registration ...................................................................................................... 6-89Jam Removal .............................................................................................................. 6-89

6.11.2 DRIVE .................................................................................................................... 6-906.11.3 TRAY AND PAPER LIFT MECHANISM TRAY 2,3 ............................................ 6-91Bottom Plate Lift.......................................................................................................... 6-91Lift Sensor................................................................................................................... 6-92

6.11.4 PAPER FEED AND SEPARATION MECHANISM................................................ 6-93Paper Feed and Separation: No Paper Present ......................................................... 6-93Paper Feed and Separation........................................................................................ 6-94Separation Roller Release Mechanism ...................................................................... 6-95

6.11.5 PAPER NEAR-END AND PAPER END TRAYS 2 AND 3.................................. 6-966.11.6 PAPER SIZE DETECTION.................................................................................... 6-97

Tandem Tray (Tray 1) ................................................................................................. 6-97Universal Cassettes (Tray 2, 3) .................................................................................. 6-97

6.11.7 ANTI-CONDENSATION HEATERS ...................................................................... 6-98

6.11.8 TANDEM TRAY TRAY 1 .................................................................................... 6-99Overview ..................................................................................................................... 6-99Connecting the Left and Right Sides of the Tray ...................................................... 6-100Paper Lift/Remaining Paper Detection ..................................................................... 6-101Fence Drive............................................................................................................... 6-103Rear Fence Drive...................................................................................................... 6-104Tray Side-to-side Positioning.................................................................................... 6-105

6.11.9 TRAY POSITIONING MECHANISM TRAYS 1 TO 3 ....................................... 6-1066.11.10 BY-PASS TRAY................................................................................................. 6-107

By-pass Feed and Separation .................................................................................. 6-107By-pass Tray Paper End Detection .......................................................................... 6-108By-pass Paper Size Detection .................................................................................. 6-109

6.11.11 PAPER REGISTRATION................................................................................... 6-110

Overview ................................................................................................................... 6-110Paper Registration Drive........................................................................................... 6-111Jam Removal at Paper Registration ......................................................................... 6-112


19/868

xv

6.12 IMAGE FUSING AND PAPER EXIT .............................................................................. 6-1136.12.1 OVERVIEW.......................................................................................................... 6-113

B064 Series............................................................................................................... 6-113B140/B246 Series ..................................................................................................... 6-114

All Series................................................................................................................... 6-114

6.12.2 FUSING MECHANISM ........................................................................................ 6-115B064 Series............................................................................................................... 6-115B140/B246 Series ..................................................................................................... 6-116

6.12.3 PRESSURE ROLLER.......................................................................................... 6-117B064 Series............................................................................................................... 6-117B140/B246 Series ..................................................................................................... 6-118

6.12.4 HOT ROLLER CLEANING .................................................................................. 6-119Overview ................................................................................................................... 6-119Web Drive ................................................................................................................. 6-120Web Near-end........................................................................................................... 6-120Web End ................................................................................................................... 6-120

6.12.5 FUSING UNIT ENTRANCE GUIDE..................................................................... 6-1216.12.6 FUSING UNIT DRIVE.......................................................................................... 6-122

6.12.7 CPM DOWN MODE............................................................................................. 6-123B140/B246 Series ..................................................................................................... 6-1236.12.8 FUSING TEMPERATURE CONTROL ................................................................ 6-1246.12.9 EXIT ..................................................................................................................... 6-1266.12.10 EXIT JUNCTION GATE..................................................................................... 6-127

6.13 DUPLEX UNIT ............................................................................................................... 6-1286.13.1 OVERVIEW.......................................................................................................... 6-1286.13.2 DUPLEX DRIVE................................................................................................... 6-1296.13.3 INVERTER OPERATION .................................................................................... 6-130

Inverter Feed-in and Jogging .................................................................................... 6-130Inverter Feed-out ...................................................................................................... 6-131

6.13.4 DUPLEX TRAY FEED ......................................................................................... 6-1326.13.5 DUPLEX INTERLEAVE FEED ............................................................................ 6-133

6.14 ENERGY SAVER MODES ............................................................................................ 6-1356.14.1 OVERVIEW.......................................................................................................... 6-1356.14.2 ENERGY SAVER MODE..................................................................................... 6-136

Entering the energy saver mode............................................................................... 6-136What happens in energy saver mode ....................................................................... 6-136Return to stand-by mode .......................................................................................... 6-136

6.14.3 LOW POWER MODE ..........................................................................................6-137Entering the low power mode ................................................................................... 6-137What happens in low power mode............................................................................ 6-137Return to stand-by mode .......................................................................................... 6-137

6.14.4 AUTO OFF MODE...............................................................................................6-138Entering auto off mode.............................................................................................. 6-138What happens in auto off mode................................................................................ 6-138

Returning to stand-by mode...................................................................................... 6-138Disabling auto off mode ............................................................................................ 6-138

6.14.5 NIGHT MODE...................................................................................................... 6-139Entering night stand-by and night modes ................................................................. 6-139What happens in night stand-by and night modes.................................................... 6-139Returning to stand-by mode...................................................................................... 6-139

6.14.6 CHANGES FOR B140 AND B246....................................................................... 6-140


20/868

xvi

7. SPECIFICATIONS ................................................................................................................. 7-1

7.1 GENERAL SPECIFICATIONS...................................................................................... 7-17.1.1 COPIER ..................................................................................................................... 7-17.1.2 ADF............................................................................................................................ 7-27.1.3 POWER CONSUMPTION ......................................................................................... 7-3

7.2 MACHINE CONFIGURATION ............................................................................................. 7-67.3 OPTIONAL EQUIPMENT..................................................................................................... 7-77.3.1 A3/DLT KIT (B475) .................................................................................................... 7-77.3.2 LCT (LARGE CAPACITY TRAY) (B473)................................................................... 7-77.3.3 3000-SHEET FINISHER WITH SADDLE-STITCH

AND 50-SHEET STAPLER (B468)............................................................................ 7-87.3.4 3000-SHEET FINISHER WITH 50-SHEET STAPLER (B469)................................ 7-107.3.5 3000-SHEET FINISHER WITH SADDLE-STITCH

AND 50-SHEET STAPLER (B674).......................................................................... 7-117.3.6 PUNCH UNIT (B377)............................................................................................... 7-147.3.7 COVER INTERPOSER TRAY (B470) ..................................................................... 7-157.3.8 3000 SHEET FINISHER (B478/B706)..................................................................... 7-167.3.9 PUNCH UNIT (B531)............................................................................................... 7-17

7.3.10 PUNCH UNIT (A812)............................................................................................. 7-187.3.11 JOGGER UNIT (B513)........................................................................................... 7-197.3.12 9-BIN MAILBOX (B471)......................................................................................... 7-197.3.13 LG/B4 KIT (B474) ..................................................................................................7-197.3.14 Z-FOLDING UNIT (B660) ...................................................................................... 7-197.3.15 3000-SHEET FINISHER B701 .............................................................................. 7-207.3.16 2000-SHEET FINISHER B700 .............................................................................. 7-227.3.17 PUNCH UNIT B702 ............................................................................................... 7-247.3.18 9-BIN MAILBOX B762 ............................................................................................ 7-24


21/868

30 June 2006 INSTALLATION REQUIREMENTS

1-1

I n s

t a l l a

t i o n1. INSTALLATION

1.1 INSTALLATION REQUIREMENTS

1.1.1 OPERATING ENVIRONMENT

1. Temperature Range: Recommended: 15 C to 25 C (59 F to 77 F)Possible: 10 C to 32 C (50 F to 90 F)

2. Humidity Range: 15% to 80% RH (27 C 80%, 32 C 54%)

3. Ambient Illumination: Less than 1,500 lux (do not expose to direct sunlight orstrong light.)

4. Ventilation: Room air should turn over at least 3 times per hour

5. Ambient Dust: Less than 0.10 mg/m 3

6. If the place of installation is air-conditioned or heated, do not place the machinewhere it will be:1) Subjected to sudden temperature changes2) Directly exposed to cool air from an air-conditioner3) Directly exposed to heat from a heater

Humidity

10C(50F)

27C(80.6F)

32C(89.6F)

15%

54%

80%

Temperature

Operation range

B064I502.WMF


22/868

INSTALLATION REQUIREMENTS 30 June 2006

1-2

7. Do not place the machine where it will be exposed to corrosive gases.

8. Do not install the machine at any location over 2,000 m (6,500 feet) above sea

level.9. Place the copier on a strong and level base with the front and back of the

machine within 5 mm (0.2") of level.

10. Do not place the machine where it may be subjected to strong vibrations.

11. Do not connect the machine to a power source shared with another electricalappliance.

12. The machine can generate an electromagnetic field which could interfere withradio or television reception.

1.1.2 MACHINE LEVEL

1. Front to back: Within 5 mm (0.2") of level

2. Right to left: Within 5 mm (0.2") of level

The machine legs may be screwed up or down in order to level the machine. Set acarpenters level on the exposure glass.


23/868


1-3

I n s

t a l l a

t i o n

1.1.3 MINIMUM SPACE REQUIREMENTS

Place the copier near the power source, providing minimum clearance as shownbelow. The same amount of clearance is necessary when optional peripheraldevices are installed.

B064I001.WMF

50 mm (2") Back

700 mm (27.6") Front

40 mm (1.6") Right100 mm (4") Left


24/868


1-4

1.1.4 DIMENSIONS

B064 Series

B064I003.WMF

B064I002.WMF

480 mm (18.9")

425 mm (16.7")

1,165 mm (45.9")

314 mm (12.4")690 mm (27.2")

734 mm (28.9")

90 mm (3.5")

1,014 mm (39.9")

1,098 mm (43.2")

750 mm (29.5")

458 mm (18")

620 mm (24.4")


25/868


1-5

I n s

t a l l a

t i o n

B140 Series

B064I140.WMF

B064I002.WMF

480 mm (18.9")

425 mm (16.7")

1,165 mm (45.9")

314 mm (12.4")690 mm (27.2")734 mm (28.9")90 mm (3.5")

1,014 mm (39.9")

1,098 mm (43.2")

177 mm (6.9")

750 mm (29.5")

458 mm (18")

620 mm (24.4")


26/868


1-6

B246 Series

B132I112.WMF

B064I002.WMF

790 mm (31.1")

458 mm (18")

613 mm (24.1")

480 mm (18.9")

425 mm (16.7")

1165 mm (45.9")

314 mm (12.4")690 mm (27.2")657mm (25.9")90 mm (3.5")

177 mm (6.9")

1103 mm (43.4")

978 mm (38.5")


27/868


1-7

I n s

t a l l a

t i o n

1.1.5 PERIPHERAL/OPTION SUMMARY TABLE

The table below summarizes all the peripheral devices and controller options thatcan be installed with the B064, B140, and B246 Series machines. O: YES, X: NO

SeriesBnnn Name B064 B140 B246 Class*1 Comment

B328 Copy Connector KitType 2105

X O X 1 Links two mainframes.

B377 Punch Unit Type1045

O O X 2 Installed in B468, B469, B674

B452 Key CounterBracket Type 1027

O O O 1 Common option.

B468 Booklet Finisher O X X 1 Punching, sorting, shifting,corner/booklet stapling.

B469 Booklet FinisherSR850

O O X 1 Punching, sorting, shifting,corner stapling only.

B470 Cover InterposerTray

O O X 2 Installed on B468, B469,B674, or B478, B706

B471 9-Bin Mailbox O O X 2 Installed on the B468, B469,or B674.

B473 LCT RT43 O O O 1 Paper bank for LT/A4 paperB474 81/2"x 14" Paper

Size Tray Type1075

O O O 1 Paper bank for LG paper

B475 A3/11"x17" TrayUnit Type 1075

O O O 1 Installed in Tray 1 (TandemTray)

B476 Copy Tray Type1075

O X X 2 Small output tray formainframe

B478 3000 Sheet Finisher O X X 1 Punching, sorting, shifting,corner stapling only.

B498 Card ReaderBracket

O O O 1 Connected directly to themainframe.

B499 Tab Sheet Holder

Type 3260

O O O 2 Installed in Tray 1 (Tandem

Manual de Servicio Para MP 6500 SM_5500_6500_7500

Documents