Step 1 Position cartridge with label facing you. Locate the drum axle spring on the cartridge left side. Using a spring hook, remove the spring from the axle. (See Photos 1, 2 & 3) Photo 1 Photo 3 Photo 4 CLP600TECH E-mail: [email protected]Website: www.futuregraphicsllc.com US 1 800 394.9900 Int’l +1 818 837.8100 FAX 1 800 394.9910 Int’l +1 818 838.7047 ATLANTA, USA US 1 877 676.4223 Int’l +1 770 516.9488 FAX 1 877 337.7976 Int’l +1 770 516.7794 MIAMI, USA US 1 800 595.429 Int’l +1 305 594.3396 FAX 1 800 522.8640 Int’l +1 305 594.3309 TORONTO, CAN CAN 1 877 848.0818 Int’l +1 905 712.9501 FAX 1 877 772.6773 Int’l +1 905 712.9502 NEW YORK, USA US 1 800 431.7884 Int’l +1 631 345.0121 FAX 1 800 431.8812 Int’l +1 631345.0690 SYDNEY, AUS AUS 1 800 003.100 Int’l +62 02 9648.2630 FAX 1800 004.302 Int’l +62 02 9548.2635 BUENOS AIRES, ARG ARG 0810 444.2656 Int’l +011 4583.5900 FAX +011 4584.3100 MONTEVIDEO,URY URY 02 902.7206 Int’l +5982 900.8358 FAX +5982 908.3816 JOHANNESBURG, S.A. S.A. +27 11 974.6155 FAX +27 11 974.3593 MELBOURNE, AUS AUS 1 800 003. 100 Int’l +62 03 9561.8102 FAX 1 800 004.302 Int’l +62 03 9561-7751 CORPORATE LOS ANGELES, USA The Samsung CLP-600 was introduced in spring of 2006. The Samsung CLP-600/650 is a follow-on product to the Samsung CLP-500/550/510. The printer prints up to 21 ppm with a first page out in less than 20 seconds. The cartridge is an all-in-one design rated at 4000 pages for black and all colors. CLP-600 CLP-600N CLP-650 CLP-650N CLP-K600A – Black (Capacity – 4K pages) CLP-C600A – Cyan (Capacity – 4K pages) CLP-M600A – Magenta (Capacity – 4K pages) CLP-Y600A – Yellow (Capacity – 4K pages) Tools required: #1 Phillips Screwdriver Small Flat Screwdriver Spring Hook Thumb Screws Supplies Required: DRUMPOWDERCPT Soft Lint-Free Cloth Conductive Grease Anhydrous Isopropyl Alcohol Vacuum or dry Compressed Air Technical Instructions Overview Printers/OEM Info Tools & Supplies 1 Step 2 Locate the cartridge pins with the threaded holes. Screw into the threaded holes the thumb screws or comparable screw with a M3 X 0.5 thread and at least 8mm in length. Remove the pins and separate the cartridge. (See Photos 4, 5 & 6) Photo 5 Photo 6 Photo 2 REV: 6/04/07
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Step 1Position cartridge with label facing you.Locate the drum axle spring on the cartridgeleft side. Using a spring hook, remove thespring from the axle. (See Photos 1, 2 & 3)
The Samsung CLP-600 was introduced inspring of 2006. The Samsung CLP-600/650 is a follow-on product tothe Samsung CLP-500/550/510.
The printer prints up to 21 ppm with a firstpage out in less than 20 seconds. Thecartridge is an all-in-one design rated at4000 pages for black and all colors.
Supplies Required:DRUMPOWDERCPTSoft Lint-Free ClothConductive GreaseAnhydrous Isopropyl AlcoholVacuum or dry Compressed Air
Technical Instructions Overview Printers/OEM Info Tools & Supplies 1
Step 2Locate the cartridge pins with the threadedholes. Screw into the threaded holes thethumb screws or comparable screw with aM3 X 0.5 thread and at least 8mm in length.Remove the pins and separate the cartridge.(See Photos 4, 5 & 6)
Photo 5
Photo 6
Photo 2
REV: 6/04/07
Step 8Clean wiper blade with a soft, dry cloth ordry, compressed air. Apply padding pow-der DRUMPOWDERCPT to the bladeedge and reinstall wiper blade.(See Photos 13 & 14)
Step 9Clean PCR saddle blocks and PCR con-tact with cotton swab and AnhydrousIsopropyl Alcohol. Clean PCR using a dry,soft, lint-free cloth.NOTE: If needed, deionized water can beused to clean the PCR.(See Photos 15 & 16)
Photo 12
Photo 13
Photo 14
2 Samsung CLP600 Technical Instructions
Photo 10
Photo 11
Step 7Remove the screws to the wiper bladeand remove wiper blade. Clean wastetoner area using a vacuum or dry,compressed air.(See Photo 12)
Step 5Remove the drum axle pushing the axialtowards the gear side of the drum.Remove the drum and set aside in a light-protected area.(See Photo 10)
Step 6Remove PCR from saddle blocks. Set PCR aside. (See Photo 11)
Photo 7
Step 3After separating the cartridge,put aside the toner unit. (See Photo 7)
Photo 8
Step 4Position the waste unit with thedrum closest to you. Removethe two E clips on each end ofthe drum axle.(See Photos 8 & 9)
Photo 9
Photo 15
Photo 16
Photo 17
Samsung CLP600 Technical Instructions 3
Step 10Apply conductive grease to the PCR con-tact. Install PCR into saddle blocks.(See Photos 17 & 18)
Step 11Clean drum using soft, dry cloth. Applypadding powder DRUMPOWDERCPT tothe drum. (See Photos 19 & 20)
Photo 19
Step 12Position drum in the waste unit. Insertrounded end of drum axle into the non-gear side of the drum. Spin axle and becareful not to damage the drum contacts.Install E clips onto drum axle.(See Photos 21 & 22)
Step 13Set aside the waste unit. Protect the drumfrom light exposure.
Step 14Starting on the toner unit, remove the twoscrews holding the contacts cover.Remove the left side developer roller endcap by separating end cap from cartridgeusing a flat screwdriver.(See Photos 23 & 24)
Photo 24
Photo 26
Photo 27
4 Samsung CLP600 Technical Instructions
Step 19Install gear cover using the two screws.(See Photo 35)
Step 20Install developer roller end cap.(See Photo 36)
Photo 34
Photo 35
Photo 36
Photo 31
Photo 33Step 18Install gear assembly using the one screw.Install the four gears.(See Photos 33 & 34)
Step 17Install developer roller spacers and drumbearings. Install developer roller into car-tridge. Insure that spacers are flush upagainst the developer roller.(See Photos 31 & 32)
Photo 28
Step 16Remove the developer roller.Remove drum bearings andspacers. Clean excess toner byblowing dry, compressed airover the developer roller. Finishwith a hand wipe using a dry,soft, lint-free cloth on the devel-oper roller, drum bearings, andspacers. (See Photos 28, 29 & 30)
Photo 29
Photo 30
Photo 32
Future Graphics (FG) is a distributor of com-patible replacement parts and products forimagining equipment. None of FG's productsare genuine OEM replacement parts and noaffiliation or sponsorship is to be impliedbetween FG and any OEM.
Photo 37
Samsung CLP600 Technical Instructions 5
Step 21Clean the contacts in the contact cover.Apply contact grease to the developerroller and supply roller contacts. Reinstallcover using the two screws.(See Photos 37, 38 & 39)
Step 22Remove fill plug, fill with toner, andreplace fill plug. Check for leaks. (See Photos 40 & 41)
Photo 39
Step 23Returning to the waste unit, locate thechip mounted in the back of the cartridge.To remove the chip, gently push the chipout of the holding area while lifting theplastic bar. Replace OEM chip with after-market chip. (See Photo 42)
Photo 40
Photo 43
Step 24Place the toner and waste unitstogether and install cartridgepins. The long pin goes to thegear side and the short pin isused in the contact side.Remove thumb screws from thecartridge pins. Install drum axlespring.(Sees Photos 43 & 44)