680276-011*2 1/14 www.teleflexgfi.nl 18-03-2008 Chevrolet D-Max 3.5 24V V6 ‘04 GNV / CNG Manual de Instalación / Fitting Instructions SGI GNV / CNG :680276-011*2 :Chevrolet :D-Max 3.5 24V V6 :‘04---> :- :- 690276-011 No.Instrucción / Instruction Nr . ...................................................................................................................... Marca / Make................................................................................................................................................. Modelo-Motor / Car-Engine type.................................................................................................................... Año de Fabricación / Model Year ................................................................................................................... Codigo de Motor / Engine Code ............................................................................................................... Sistema de Gestión del motor / Motor Management..................................................................................... Kit No. / Kit Nr ................................................................................................................................................ INSTRUCCIONES GENERALES Cuando instale el Sistema de GNV, se require cumplir con las siguientes instrucciones: * Es de responsabilidad del instalador cumplir con las regulaciones locales y/o nacionales y realizar las adaptaciones necesarias. * Previo el inicio de la instalación del sistema de GNV, favor desconectar el cable negativo de la batería. * De ser necesario, favor consultar los manuales de instalación del vehiculo antes de desconectar cualquier parte del mismo. * Todas las direcciones que se indican en este manual hacen referencia a la dirección del flujo. * Todas las medidas en este manual, son en milímetros (mm), salvo las especificadas. * Cuando taladre, tener cuidado especial en las partes inferiores. * Limar los agujeros y tratarlos contra corrosión. * Cuando instale el pico de los inyectores, picos de vacío, picos de agua, picos de gas y la válvula de GNV, use agente sellador en la roscas. * Siempre utilice aceite en los anillos (o-rings) del sostén de inyectores GFI (si aplicable). * Utilice las abrazaderas de mangueras correctas cuando instale las mismas. * Una vez instalado el Sistema de GNV, asegúrese de que las líneas de agua estén totalmente selladas. * Utilice siempre los conectores eléctricos enviados junto con el equipo y asegúrese de aislarlos completamente. No soldar. * Prevenir el riesgo de daño prematuro del cableado y mangueras. Asegúrelas con los Sujetadores de cable sumistrados. Siempre asegúrese de chequear los siguientes puntos del manual de Instalación de TeleflexGFI GNV: 1. Revisar toda la instalación de fugas/escapes de GNV, Gasolina, refrigerante y aire. 2. Inyectores deben estar conectados correctamente --->Use la herramienta de Diagnostico (DTS) y el Break-Out Box (BOB) # 3. Presión (DelP): 1750<-->2000mBar a temperatura de trabajo --->Use la herramienta de Diagnostico (DTS) 4. Códigos de Errores del Sistema de GNV & Gasolina : Reparar el malfuncionamiento (si aplica) y borrar los códigos ---> Use la Herramienta de Diagnostico (DTS) & Instrumento OBD * 5. Realice una prueba práctica de manejo y repita el punto 4. *Observaciones: Vehículos modernos pueden ser equipados con un indicador de nivel para Gasolina y computadora de bordo que indica y calcula la cantidad consumida de combustible. Un posible resultado es que, no obstante operando en modo GNV, el indicador de Gasolina continúe decreciendo y la computadora de bordo indicar un consumo de combustible erróneo y rango de operación. Como resultado el Sistema de Gasolina indicaría un “Código de Error”. En este caso, el Sistema SGI no interfiere ni tiene influencia. TeleflexGFI no asumirá responsabilidad alguna por esta situación. GENERAL INSTRUCTIONS When installing the CNG installation,compliance is required with the following guidelines: * It’s the installer’s responsibility to check the national and/or local regulations and to make all necessary adaptions. * Before commencing the installation of the CNG installation, remove the negative terminal from the battery. * If necessary, consult the workshop manual of the relevant car before the parts are disassembled. * All directions in the installation manual are given from the direction of the traffic. * Unless indicated otherwise, all measurements are in mm. * When drilling be careful for the underlying parts! * Deburr holes in the plating and treat them for rust. * When fitting the injector nipples, vacuum nipples, water nipples, gas nipples and CNG valve, use sealing locking agent on the screwthread. * Always oil the O-rings of the GFI injector holders(when applicable). * Use the right hose clips when fitting all hoses. * After installing the CNG installation, ensure a watertight seal on the cable and pipe lead-throughs. * Use the connectors supplied for electrical connections and then insulate them completely. Do not solder! * Prevent the risk of damage from wiring harnesses and hoses. Fasten them with the cable ties supplied Always check after installing of the TeleflexGFI CNG installation: 1.The entire installation for leaks of CNG,petrol,coolant and air. 2.Injectors correct connected ---> Use Diagnose Tool (DTS) & Break-Out Box(BOB) # 3.Pressure(DelP) : 1750<-->2000mBar at working temperature ---> Use Diagnose Tool (DTS) 4.Error codes CNG & Petrol system : Repair malfunction(if applicable) & delete codes ---> Use Diagnose Tool (DTS) & OBD Tool * 5.Driveability by means of a testdrive and repeat point 4. *Remark: Modern cars can be equipped with a petrol level indicator and boardcomputer which displayed indication is related to the,by petrol computer calculated,fuel consumption. A possible consequence is that,although driving on CNG,the petrol level indicator will still decrease and the boardcomputer will display the wrong fuel consumption and operating range. As a result of this the petrol system may also generate an "Error code". The SGI system is not able to have any influence on this.TeleflexGFI will not take any responsibility for this situation.
14
Embed
Manual de Instalación / Fitting Instructions SGI GNV ...diagramasde.com/diagramas/otros2/d max chevrolet manual instalacion... · Manual de Instalación / Fitting Instructions SGI
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
No.Instrucción / Instruction Nr. ......................................................................................................................
Marca / Make.................................................................................................................................................
Cuando instale el Sistema de GNV, se require cumplir con las siguientes instrucciones:
* Es de responsabilidad del instalador cumplir con las regulaciones locales y/o nacionales y realizar las adaptaciones necesarias.* Previo el inicio de la instalación del sistema de GNV, favor desconectar el cable negativo de la batería.* De ser necesario, favor consultar los manuales de instalación del vehiculo antes de desconectar cualquier parte del mismo.* Todas las direcciones que se indican en este manual hacen referencia a la dirección del flujo.* Todas las medidas en este manual, son en milímetros (mm), salvo las especificadas.* Cuando taladre, tener cuidado especial en las partes inferiores.* Limar los agujeros y tratarlos contra corrosión.* Cuando instale el pico de los inyectores, picos de vacío, picos de agua, picos de gas y la válvula de GNV, use agente sellador en la roscas.* Siempre utilice aceite en los anillos (o-rings) del sostén de inyectores GFI (si aplicable).* Utilice las abrazaderas de mangueras correctas cuando instale las mismas.* Una vez instalado el Sistema de GNV, asegúrese de que las líneas de agua estén totalmente selladas.* Utilice siempre los conectores eléctricos enviados junto con el equipo y asegúrese de aislarlos completamente. No soldar.* Prevenir el riesgo de daño prematuro del cableado y mangueras. Asegúrelas con los Sujetadores de cable sumistrados.
Siempre asegúrese de chequear los siguientes puntos del manual de Instalación de TeleflexGFI GNV:1. Revisar toda la instalación de fugas/escapes de GNV, Gasolina, refrigerante y aire.2. Inyectores deben estar conectados correctamente --->Use la herramienta de Diagnostico (DTS) y el Break-Out Box (BOB) #3. Presión (DelP): 1750<-->2000mBar a temperatura de trabajo --->Use la herramienta de Diagnostico (DTS) 4. Códigos de Errores del Sistema de GNV & Gasolina : Reparar el malfuncionamiento (si aplica) y borrar los códigos ---> Use la Herramienta de Diagnostico
(DTS) & Instrumento OBD *5. Realice una prueba práctica de manejo y repita el punto 4.
*Observaciones: Vehículos modernos pueden ser equipados con un indicador de nivel para Gasolina y computadora de bordo que indica y calcula la cantidad consumida de combustible.Un posible resultado es que, no obstante operando en modo GNV, el indicador de Gasolina continúe decreciendo y la computadora de bordo indicar un consumo de combustible erróneo y rango de operación.Como resultado el Sistema de Gasolina indicaría un “Código de Error”.En este caso, el Sistema SGI no interfiere ni tiene influencia. TeleflexGFI no asumirá responsabilidad alguna por esta situación.
GENERAL INSTRUCTIONS
When installing the CNG installation,compliance is required with the following guidelines:
* It’s the installer’s responsibility to check the national and/or local regulations and to make all necessary adaptions.* Before commencing the installation of the CNG installation, remove the negative terminal from the battery.* If necessary, consult the workshop manual of the relevant car before the parts are disassembled.* All directions in the installation manual are given from the direction of the traffic.* Unless indicated otherwise, all measurements are in mm.* When drilling be careful for the underlying parts!* Deburr holes in the plating and treat them for rust.* When fitting the injector nipples, vacuum nipples, water nipples, gas nipples and CNG valve, use sealing locking agent on the screwthread.* Always oil the O-rings of the GFI injector holders(when applicable).* Use the right hose clips when fitting all hoses.* After installing the CNG installation, ensure a watertight seal on the cable and pipe lead-throughs.* Use the connectors supplied for electrical connections and then insulate them completely. Do not solder!* Prevent the risk of damage from wiring harnesses and hoses. Fasten them with the cable ties supplied
Always check after installing of the TeleflexGFI CNG installation: 1.The entire installation for leaks of CNG,petrol,coolant and air.2.Injectors correct connected ---> Use Diagnose Tool (DTS) & Break-Out Box(BOB) #3.Pressure(DelP) : 1750<-->2000mBar at working temperature ---> Use Diagnose Tool (DTS) 4.Error codes CNG & Petrol system : Repair malfunction(if applicable) & delete codes ---> Use Diagnose Tool (DTS) & OBD Tool *5.Driveability by means of a testdrive and repeat point 4.
*Remark: Modern cars can be equipped with a petrol level indicator and boardcomputer which displayed indication is related to the,by petrol computer calculated,fuel consumption.A possible consequence is that,although driving on CNG,the petrol level indicator will still decrease and the boardcomputer will display the wrong fuel consumption and operating range.As a result of this the petrol system may also generate an "Error code".The SGI system is not able to have any influence on this.TeleflexGFI will not take any responsibility for this situation.
Manual de Instalación / Fitting Instructions SGI GNV / CNG
4 Sensor de Temperatura del Aire / Air Temperature Sensor
OBJETIVO PRINCIPAL / MAIN OBJECTIVE:
Distancia Y= LA MAS PRÓXIMA POSIBLE
Distance Y=AS SMALL AS POSSIBLE
Lo más cerca de motorClosest to engine
Ø10.8mm M12x1.25 ++
238013-234
Y
6 CYL. (6x)
ELECCIÓN CIL. + POSICIÓN ARBITRARIACHOICE CYL. + POSITION ARBITRARILY
Observaciónes:
* Siempre retirar el Colector de Admisión / Always remove inlet manifold* Reemplazar empaques / Replace gaskets* Inyectores + Mangueras: Asegurarse el no ingreso de partículas / Keep injectors + hoses safe from particles
Manual de Instalación / Fitting Instructions SGI GNV / CNG
Distancia Y= LA MAS PRÓXIMA POSIBLE / (6x) DISTANCIA IGUAL
Distance Y=AS SMALL AS POSSIBLE / (6x) EQUAL DISTANCE
Lo más cerca de motorClosest to engine
No desarreglar inyecciónes de gasolinaDo not disturb petrol injections
Preferencia / Preference
Cara de arriba / Top side
100mm
(((
COLOCACIÓN (A-A) / POSITIONING (A-A) ):
300300-011
PREFERENCIAS / PREFERENCES
Ø8.5mm M10x1 ++ *Siempre utilice aceite en los anillos (o-rings) del pézon de inyectores*Always oil the O-rings of the injector holders
Preparación / Preparation300300-011 (6x)
V6
A A
Observaciónes:
* Siempre retirar el Colector de Admisión / Always remove inlet manifold* Reemplazar empaques / Replace gaskets* Inyectores + Mangueras: Asegurarse el no ingreso de partículas / Keep injectors + hoses safe from particles