Manuals1, Make the out-frame (housing/support) first, Or you can
fix the LED display directly without the housing. Pls ask your
local decoration or building company make the structure (housing)
or fix the LED display. You can refer to the engineering
installation reference guide,Frame and Frame1. If you install the
LED display on somewhere for permanent or fixed install, pls make
sure the LED display cabinet back door can open at the back. Then
its convenient for maintain later. The LED screen is heavy, pls
make sure the structure or stand can load it. Total LED display is
around 1000kgs. After the structure or stand finished, then you can
assemble the LED cabinets, when you assemble the cabinets, Pls
refer to the cabinets connect pictures. 2, Connect Power cable and
signal cables. Make sure the Power can load the LED display, you
need to use TWO 63A switches (220V) or ONE 80A switch, and the max
power of your screen is about 19KW. If there have 3 phase power in
your country, its better use 3phase electricity. Make sure you use
the quality internet cable if we didnt prepare for you so that the
signal can send better. Regarding the power cable and communication
cable on the displays, pls refer to the cabinets connect picture.
We prepared all the cables. Attention: Only for the expert
operator, especially the power part should be operated by the
expert electrician to ensure the safety.
3, Operation Steps:(1), Get one PC with Windows 2000/XP/ME
System. (2), Open PC host cabinet when PC power off, put sending
card and ATI video card into PCI and VGA Separately. Pls refer to
the video (sending& display card installation) (3), Setup PC
and install ATI video card driver program, then install LED display
software, LED studio. (in the prepared CD) (4), Set Video card
parameter, please reference to Model 801 and 802 Manual.
(Attachment B) (5), Led Screen installation steps: Unpack the
package, checking cabinet is broken or inner wire is loosed or
not.
Install LED screen according to our installation and cable
drawing ( cabinets connect pictures) Connect signal cable and power
supply cable according to our installation and cable drawing
(cabinets connect pictures). Connect LED screen and PC by internet
cable; Connect Video card and sending card by DVI cable; Connect PC
and sending card by Serial cable according to our installation and
cable drawing. AttentionWhen connection DVI cable, computer must
power off. Test Power Supply cable connection is right or not. Only
when right, then power on LED screen. (6), Open PC and LED screen
power supply, then LED screen begin to work. Led screen will
display some pictures on the LED screen monitor. Start LED studio
and Adjust the Display Window to be whole area. If it shows the
wrong or littery or overlap pictures, please refer to attachment C
( This step is setting the systems parameter, please be careful)
(7), Use LED studio to show content, please refer to LED studio
manual. (8), Close LED display, then close PC.
COM serial Port Connect to sending card
VGA Port connect to Pc Monitor DVI Port connect to Sending card
RJ45 Port connect to Receiving card
Attachment A
LED Display Adjustment StepsStep 1: check sending card's green
light whether it glitters regularly; if glitters,
please enter the third step; if not, please restart the
computer; before entering Win2000/xp/Me, please check sending
card's green light whether it glitters regularly, if so, please
enter the second step, and check DVI line whether it is connected
well. If the problem still exists, there must be something wrong
among sending card, graphic card and DVI line, please alter them,
then redo following the first step. Step 2: please set or reset
according to the Attachment B until green signal light on the
sending card flashes regularly, otherwise repeat step 1. Step3:
check green signal light(data light) on receiving card to see if it
glitters with the one on the sending card synchronistical. If yes,
turn to step 5, and then check the red signal light (power supply)
to see if it is powered on, if yes, please turn to step 4, if not,
then check the yellow signal light (power supply protection) to see
if it is powered on, if not, please check the power to see if it is
connected reverse or power no output. If the yellow signal light is
powered on, please check the voltage to make sure it is 5V. if yes,
please turn off the power and get off transfer card and 50P
drop-out line and try it again. If still problem, there must be
receiving card problems, please change the receiving card and
repeat step 3. Step 4: check internet cable if it is connected well
and too long or not? And also Check that the internet cable is made
according to the standard, which is illustrated in Attachment D(we
prepared the cable to you). if it still can not work, there may be
something wrong with the receiving card, change a new one and
repeat step 3. Step 5Check power supply lamp of LED display flash
or not? If it doesnt flash, turn to step 4, check the transfer card
interface definition if it is matches
with LED modules.
Attachment B
ATI Template Setting Aim 1. Set right screen resolution. For
example: 1024 by 768 pixels. 2. Set right screen refresh rate. It
must be 60-75HZ. 3. Open FPD out port. 4. Set overlay display mode
to 'Same on all'. Operation 1. Right mouse button click on desktop
and then select properties menu, you will see Display Properties
dialog. Set suitable screen resolution, and see follows:
2. Click advanced button, and set screen refresh rate
60-75HZ.
3. Click Display property page, and click FPD button to make it
green. Make sure FPD port is opened.
4. Click Overlay property page, and click 'Clone mode options'
button to set overlay display mode to 'Same on all'. See
follows:
Attachment COperation ManualOperation for technicians, the inner
connect to the port near the indicator light. Do not to operate
like this if the display works well. 1, Open the LED studio 2,
Click Option, then click "software setup".
3, Click the windows(blue color frame), Pls refer to the below
pictures. Input" linsn" directly. Dont care about there something
come or not, just type the linsn directly on the keyboard after
click the windows frame (blue color frame).
4, after type the linsn, there a window will ask for the
password, password168
5, after insert the password, there a window will come like the
below picture, Click sender. Then click Save on sender, Make sure
click Save on sender.
6, Click receiver,Then click "load from files" .RCG. Then, Click
Send to receiver, ,
,Select files P10 (.RCG file
can find in CD we prepared for you. Pls copy to your computer
first when you use it.)
Pls refer to the below parameter setup.
After load files, the below window will come, pls click all.
ClickY, Then click save on receiver.
7, Click Display connection. Then Click "load from files",
Select files P10.CON. Then click Send to receiver.(The Connection
.CON file can find in CD we prepared for you. Pls copy it to your
computer first when you use it)
Attachment D1, Net cable
How to make cable
A and B port : 1, White orange,2:orange,3:White green,4: blue,5:
White blue,6:green, 7 :white brown,8: brown. 2, 3 core power cable,
if have two ports, It's the same connect.
3, 9 core data cable , if have two ports , It's the same
connect.