QUICK INSTALLATION
Wireless-G PCI AdapterINSTRUCTIONS FOR WINDOWS VISTA USERS
ONLY
Package Contents
Wireless-G PCI Adapter or Wireless-G PCI Adapter with
SpeedBooster or Wireless-G PCI Adapter with RangeBooster Setup
Wizard CD-ROM User Guide on CD-ROM Quick Installation
Model:
WMP54G WMP54GS WMP54GR
1 InstallationThe Adapter is installed and set up using the
Setup Wizard on the enclosed Setup Wizard CD. This Quick
Installation is for Windows Vista users only. If you have Windows
XP or 2000, use the other enclosed Quick Installation. IMPORTANT:
Do not install the Adapter in your computer until you are
instructed to do so, or the Adapter will not install correctly.
A.
Insert the Setup Wizard CD into your CD-ROM drive.
Insert the CD-ROM
NOTE: Windows Vista or other personal firewalls may ask for
permission to run the software or program. You will need to allow
the software to run in order to continue.
B.
The Welcome screen appears on your monitor. Click the Click Here
to Start button.
Click Here to Start
C.
Read the License Agreement, and click Next to continue the
installation.
License Agreement
D.1. 2.
Follow the instructions to physically install the Adapter: Power
off your computer. After installing the Adapter, as described
below, and restarting your computer, the Setup Wizard will
continue. Open your computer case, and locate an available PCI slot
on the motherboard. Check with your computer manufacturer for
instructions.
Install the Adapter
3. 4. 5. 6.
Slide the Adapter into the slot. Make sure that all of its pins
touch the slots contacts. You may have to apply some pressure to
slide the Adapter all the way in. Secure its fastening tab to your
computers chassis with a mounting screw. Close your computer case.
Power on your computer, and proceed to step E.
E.
After you install the Adapter correctly, the Congratulations
screen appears. Click Finish.
Congratulations
F.
The first Windows Vista Wireless Network Configuration utility
screen appears. Select your network, and then click Connect.
Select Network
G.
If your network has no wireless security, this screen appears.
If your network has wireless security, go to step H. To connect to
your unsecured network, click Connect Anyway and go to step
I.Unsecured Network
H.
If your network has wireless security, this screen appears.
Enter the security key or passphrase (also known as pre-shared key
or WEP key, depending on your type of security). Click
Connect.Secured Network
I.
This screen appears while the Adapter connects to your network.
Do not cancel, unless you want to end the installation.
Connecting to Network
J.
This screen appears when you are connected to your network.
Select Save this network, if you want to save your settings. Click
Close.
Connected to Network
K.
The Set Network Location screen may appear to help apply the
correct settings for your type of location. If it doesnt appear, go
to step M. Select Home, Work, or Public location.
Select Network Location
L.
This screen varies according to the selected location. Click
Close.
Network Settings Saved
M. The Windows Vista Wireless
Network Configuration utility icon appears on your desktops
system tray.
Windows Vista Wireless Network Configuration Utility Icon
You can use this utility to configure or change your wireless
settings.
Wireless Connection Status
NOTE: For help with the Windows Vista Wireless Network
Configuration utility, refer to Windows Vista Help and Support, by
clicking Vistas Start button > Help and Support.
Congratulations! Setup is complete.
INSTALLATIONS VEJLEDNING
Trdls-G PCI-netvrkskortVEJLEDNING KUN TIL WINDOWS
VISTABRUGERE
Pakkens indhold
Trdls-G PCI-netvrkskort eller Trdls-G PCI-netvrkskort med
SpeedBooster eller Trdls-G PCI-netvrkskort med RangeBooster Cd-rom
med guidet konfiguration Brugervejledning p cd-rom
Installationsvejledning
Model:
WMP54G WMP54GS WMP54GR
1 InstallationNetvrkskortet installeres og konfigureres ved hjlp
af den guidede konfiguration p cden Setup Wizard, som medflger.
Denne installationsvejledning er kun til Windows Vista-brugere.
Hvis du har Windows XP eller 2000, skal du bruge den anden
medflgende installationsvejledning. VIGTIGT: Installer ikke
netvrkskortet p computeren, fr du bliver bedt om det - ellers
installeres netvrkskortet ikke korrekt.
A.
Placer cden med den guidede konfiguration i cd-rom-drevet.
Indst cd-romen
BEMRK: Windows Vista Firewall eller en separat firewall vil mske
anmode om tilladelse til at kre softwaren eller programmet. Giv
softwaren tilladelse til at kre for at fortstte.
B.
Skrmbilledet Welcome (Velkommen) vises p skrmen. Klik p knappen
Click Here to Start (Klik her for at starte).
Klik her for at starte
C.
Ls licensaftalen, og klik p Next (Nste) for at fortstte
installationen.
Licensaftale
D.1. 2.
Flg vejledningen til fysisk installation af netvrkskortet: Sluk
computeren. Nr du har installeret netvrkskortet som beskrevet
herunder og genstartet computeren, fortstter den guidede
konfiguration. bn computerens kabinet, og find et ledigt PCI-stik p
bundkortet. Henvend dig til din computerleverandr for at f
yderligere vejledning.
Installation af netvrkskortet
3. 4. 5. 6.
Skub netvrkskortet ind i stikket. Kontroller, at alle benene
berrer kontaktpunkterne i stikket. Det kan vre ndvendigt at trykke
lidt hrdt for at skubbe kortet helt ind i stikket. Skru
fastgrelsesbjlen fast p computerens kabinet med en monteringsskrue.
Luk computerens kabinet. Tnd computeren, og fortst med trin E.
E.
Nr kortet er installeret korrekt, vises skrmbilledet
Congratulations (Tillykke). Klik p Finish (Udfr).
Tillykke
F.
Det frste skrmbillede i Windows Vista-hjlpeprogrammet
Konfiguration af trdlst netvrk vises. Vlg dit netvrk, og klik
derefter p Connect (Opret forbindelse).
Vlg netvrk
G.
Hvis det trdlse netvrk ikke er beskyttet, vises dette
skrmbillede. G til trin H, hvis det trdlse netvrk er beskyttet.
Hvis du vil oprette forbindelse til det ubeskyttede netvrk, skal du
klikke p Connect Anyway (Opret forbindelse alligevel ) og g til
trin I.Ubeskyttet netvrk
H.
Hvis det trdlse netvrk er beskyttet, vises dette skrmbillede.
Indtast sikkerhedsnglen eller adgangsordet (kaldes ogs WEP-ngle
eller pre-shared key, afhngigt af sikkerhedstypen). Klik p Connect
(Opret forbindelse).Beskyttet netvrk
I.
Dette skrmbillede vises, mens netvrkskortet opretter forbindelse
til netvrket. Annuller ikke processen, medmindre du vil afslutte
installationen.
Opret forbindelse til netvrk
J.
Dette skrmbillede vises, nr der er oprettet forbindelse til
netvrket. Vlg Save this network (Gem dette netvrk), hvis du vil
gemme indstillingerne. Klik p Close (Luk).Forbindelse til netvrk
oprettet
K.
Skrmbilledet Set Network Location (Angiv netvrksplacering) kan
blive vist som en hjlp til angivelse af de rigtige indstillinger
for din type placering. G til trin M, hvis det ikke vises. Vlg Home
(Hjem), Work (Arbejde) eller Public location (Offentlig
placering).Vlg netvrksplacering
L.
Skrmbilledets udseende afhnger af den valgte placering. Klik p
Close (Luk).
Netvrksindstillinger gemt
M. Ikonet for Windows Vista-
hjlpeprogrammet Konfiguration af trdlst netvrk vises p
skrivebordets proceslinje.Ikon for Windows Vista-hjlpeprogrammet
Konfiguration af trdlst netvrk
Du kan bruge hjlpeprogrammet til at konfigurere eller ndre de
trdlse indstillinger.
Status for trdls forbindelse
BEMRK: Du kan f hjlp til Windows Vista-hjlpeprogrammet
Konfiguration af trdlst netvrk i Windows Vista Hjlp og support, som
du kan bne ved at klikke p knappen Start Support (Hjlp og support)
i Windows Vista. Tillykke! Konfigurationen er frdig. > Help
and
Yderligere oplysninger eller hjlp til fejlfinding finder du i
brugervejledningen p cd-romen. Yderligere support kan ogs fs via
e-mail eller over telefonen. Websted http://www.linksys.eu
Produktregistrering: http://www.linksys.com/registration
Linksys er et registreret varemrke tilhrende Cisco Systems, Inc.
og/eller Cisco Systems associerede selskaber i USA og visse andre
lande. Copyright 2007 Cisco Systems, Inc. Alle rettigheder
forbeholdes. Andre produktmrker og produktnavne er varemrker eller
registrerede varemrker tilhrende deres respektive ejere.
70517NC-JL
KURZANLEITUNG
Wireless-G PCIAdapterANWEISUNGEN NUR FRNUTZER VON WINDOWS
VISTA
Lieferumfang
Wireless-G PCI-Adapter oder Wireless-G PCI-Adapter mit
SpeedBooster oder Wireless-G PCI-Adapter mit RangeBooster
Setup-Assistenten-CD-ROM Benutzerhandbuch auf CD-ROM
Kurzanleitung
Modell:WMP54G
WMP54GS WMP54GR
1 InstallationDer Adapter wird ber den Setup-Assistenten, der
auf der beigefgten Setup-Assistenten-CD enthalten ist, installiert
und eingerichtet. Diese Kurzanleitung richtet sich nur an Nutzer
von Windows Vista. Verwenden Sie bitte die andere beiliegende
Kurzanleitung, wenn Sie Windows XP oder 2000 nutzen. WICHTIG:
Installieren Sie den Adapter erst dann auf Ihrem Computer, wenn Sie
dazu aufgefordert werden. Andernfalls erfolgt keine korrekte
Installation des Adapters.
A.
Legen Sie die Setup-Assistenten-CD in Ihr CD-ROM-Laufwerk
ein.
CD-ROM einlegen
HINWEIS: Bei Windows Vista oder anderen persnlichen Firewalls
ist u.U. eine Erlaubnis zur Ausfhrung der Software oder des
Programms erforderlich. Sie mssen das Ausfhren der Software
genehmigen, bevor Sie fortfahren knnen.
B.
Das Fenster Welcome (Willkommen) wird auf dem Monitor angezeigt.
Klicken Sie auf die Schaltflche Click Here to Start (Klicken Sie
hier, um zu starten).
Click Here to Start (Klicken Sie hier, um zu starten)
C.
Lesen Sie die Lizenzvereinbarung, und klicken Sie auf Next
(Weiter), um sie zu akzeptieren.
License Agreement (Lizenzvereinbarung)
D.1. 2.
Befolgen Sie die Anweisungen, um den Adapter physisch zu
installieren: Schalten Sie Ihren Computer aus. Installieren Sie den
Adapter wie unten beschrieben, und starten Sie den Computer neu.
Der Setup-Assistent wird automatisch fortgesetzt. ffnen Sie das
Gehuse des Computers, und suchen Sie einen freien PCI-Steckplatz
auf der Systemplatine. Weitere Anweisungen erhalten Sie von Ihrem
Computerhersteller.
Installieren des Adapters
3.
Stecken Sie den Adapter in den Steckplatz. Stellen Sie sicher,
dass alle Pins die Kontakte des Steckplatzes berhren. Sie mssen
beim Einstecken des Adapters u.U. ein wenig Druck ausben, damit er
fest im Steckplatz verankert ist. Befestigen Sie die Lasche mit
einer Schraube am Rahmen des Computers. Schlieen Sie das Gehuse des
Computers. Schalten Sie Ihren Computer ein, und fahren Sie mit
SchrittE fort.
4. 5. 6.
E.
Nach der ordnungsgemen Installation des Adapters wird das
Fenster Congratulations (Gratulation) angezeigt. Klicken Sie auf
Finish (Fertig stellen).
Congratulations (Gratulation)
F.
Das erste Fenster des WindowsVista Konfigurationsdienstprogramms
fr die Wireless-Verbindung wird angezeigt. Whlen Sie Ihr Netzwerk
aus, und klicken Sie anschlieend auf Connect (Verbinden).
Netzwerk auswhlen
G.
Wenn Ihr Netzwerk nicht ber Wireless-Sicherheit verfgt, wird
dieses Fenster angezeigt. Fahren Sie mit SchrittH fort, wenn Ihr
Netzwerk ber Wireless-Sicherheit verfgt. Klicken Sie auf Connect
Anyway (Trotzdem verbinden), und fahren Sie mit SchrittI fort, um
eine Verbindung zu Ihrem ungesicherten Netzwerk herzustellen.
Ungesichertes Netzwerk
H.
Wenn Ihr Netzwerk ber WirelessSicherheit verfgt, wird dieses
Fenster angezeigt. Geben Sie den Sicherheitsschlssel oder die
Passphrase ein (wird auch als vorlufiger gemeinsamer Schlssel oder
WEP-Schlssel bezeichnet, je nach Sicherheitstyp). Klicken Sie auf
Connect (Verbinden).Abgesichertes Netzwerk
I.
Dieses Fenster wird angezeigt, wenn der Adapter eine Verbindung
zum Netzwerk herstellt. Brechen Sie diesen Vorgang nicht ab, wenn
Sie die Installation nicht beenden mchten.
Netzwerkverbindung wird hergesellt
J.
Dieses Fenster wird angezeigt, wenn eine Verbindung zum Netzwerk
hergestellt wurde. Whlen Sie Save this network (Dieses Netzwerk
speichern) aus, wenn Sie Ihre Einstellungen speichern mchten.
Klicken Sie auf Close (Schlieen).Netzwerkverbindung hergesellt
K.
Das Fenster Set Network Location (Netzwerkstandort festlegen)
wird u.U. angezeigt, um Ihnen zu helfen, die korrekten
Einstellungen fr Ihren Standort festzulegen. Fahren Sie mit
SchrittM fort, wenn das Fenster nicht angezeigt wird. Whlen Sie
Home (Zu Hause), Work (Arbeitsplatz) oder Public location
(ffentlicher Ort).
Netzwerkstandort auswhlen
L.
Je nach ausgewhltem Standort wird ein anderes Fenster angezeigt.
Klicken Sie auf Close (Schlieen).
Netzwerkeinstellungen gespeichert
M. Das Symbol fr das WindowsVista
Konfigurationsdienstprogramm fr die Wireless-Verbindung wird in
der Systemablage Ihres PCs angezeigt.Symbol fr das WindowsVista
Konfigurationsdienstprogramm fr die Wireless-Verbindung
Sie knnen dieses Dienstprogramm nutzen, um die
WirelessEinstellungen zu konfigurieren oder zu ndern.
Wireless-Verbindungsstatus
HINWEIS: Wenn Sie Fragen zum WindowsVista
Konfigurationsdienstprogramm fr die Wireless-Verbindung haben,
rufen Sie Windows Vista Hilfe und Support auf, indem Sie in Vista
auf die Schaltflche Start Support klicken. Gratulation! Die
Einrichtung ist abgeschlossen. und dann auf Hilfe und
Weitere Informationen sowie Anleitungen zur Fehlerbehebung
finden Sie im Benutzerhandbuch auf der CD-ROM. Zustzlichen Support
erhalten Sie per E-Mail oder Telefon. Website Deutschland
http://www.linksys.de sterreich http://www.linksys.at Schweiz
http://www.linksys.com/international Produktregistrierung
Deutschland http://www.linksys.com/de/registrierung sterreich
http://www.linksys.com/at/registrierung Schweiz
http://www.linksys.com/ch/registrierung
Linksys ist eine eingetragene Marke bzw. eine Marke von Cisco
Systems, Inc. und/oder deren Zweigunternehmen in den USA und
anderen Lndern. Copyright 2007 Cisco Systems, Inc. Alle Rechte
vorbehalten. Andere Handelsmarken und Produktnamen sind Marken bzw.
eingetragene Marken der jeweiligen Inhaber. 70517NC-JL
GUA DE INSTALACIN RPIDA
Adaptador PCI Wireless-GINSTRUCCIONES SLO PARA USUARIOS DE
WINDOWS VISTA
Contenido del paquete
Adaptador PCI Wireless-G o Adaptador PCI Wireless-G con
SpeedBooster o Adaptador PCI Wireless-G con RangeBooster CD-ROM del
asistente de configuracin Gua del usuario en CD-ROM Gua de
instalacin rpida
Modelo:
WMP54G WMP54GS WMP54GR
1 InstalacinEl adaptador se instala y configura mediante el
asistente que se incluye en el CD adjunto del asistente de
configuracin. Esta gua de instalacin rpida slo es vlida para
usuarios de Windows Vista. Si tiene Windows XP o 2000, utilice la
otra gua de instalacin rpida adjunta. IMPORTANTE: No instale el
adaptador en el ordenador hasta que no reciba la indicacin a tal
efecto, pues de lo contrario ste no se instalara correctamente.
A.
Introduzca el CD del asistente de configuracin en la unidad de
CD-ROM.
Inserte el CD-ROM
NOTA: Windows Vista o cualquier otro firewall personal podra
pedirle permiso para ejecutar el software o el programa. Deber
permitir que se ejecute el software para poder continuar.
B.
La pantalla Welcome (Bienvenido) aparecer en el monitor. Haga
clic en el botn Click Here to Start (Haga clic aqu para
empezar).
Click Here to Start (Haga clic aqu para empezar)
C.
Lea el acuerdo de licencia y haga clic en Next (Siguiente) para
continuar la instalacin.
License Agreement (Acuerdo de licencia)
D.1. 2.
Siga las instrucciones para instalar fsicamente el adaptador:
Apague el ordenador. Despus de instalar el adaptador como se
describe a continuacin y de reiniciar el ordenador, el asistente de
configuracin continuar el proceso. Abra la carcasa del ordenador y
busque una ranura PCI disponible en la placa base. Consulte las
instrucciones del fabricante del ordenador.
Instale el adaptador
3. 4. 5. 6.
Inserte el adaptador en la ranura. Asegrese de que todas las
patillas tocan los contactos de la ranura. Quiz tenga que presionar
un poco para que el adaptador encaje completamente. Fije la lengeta
de sujecin a la carcasa del ordenador mediante un tornillo de
montaje. Cierre la carcasa del ordenador. Encienda el ordenador y
vaya al paso E.
E.
Despus de instalar correctamente el adaptador, aparece la
pantalla Congratulations (Enhorabuena). Haga clic en Finish
(Finalizar).
Congratulations (Enhorabuena)
F.
Aparecer la primera pantalla de la utilidad de configuracin de
red inalmbrica de Windows Vista. Seleccione la red y haga clic en
Connect (Conectar).
Seleccione la red
G.
Si su red no tiene seguridad inalmbrica, aparecer esta pantalla.
Si su red tiene seguridad inalmbrica, vaya al paso H. Para
conectarse a una red no segura, haga clic en Connect anyway
(Conectar de todas formas) y vaya al paso I.Red no segura
H.
Si su red tiene seguridad inalmbrica, aparecer esta pantalla.
Introduzca la clave de seguridad o frase de paso (tambin conocida
como clave precompartida o clave WEP, dependiendo de su tipo de
seguridad). Haga clic en Connect (Conectar).Red segura
I.
Aparecer esta pantalla mientras el adaptador se conecta a la
red. No cancele el proceso, a no ser que quiera finalizar la
instalacin.
Conectando a red
J.
Aparecer esta pantalla cuando est conectado a la red. Seleccione
Save this network (Guardar esta red) si desea guardar sus
parmetros. Haga clic en Close (Cerrar).Conectado a red
K.
Es posible que aparezca la pantalla set Network Location
(Establecer ubicacin de red) para ayudarle a aplicar los parmetros
correctos correspondientes a su tipo de ubicacin. Si no aparece,
vaya al paso M. Seleccione Home (Casa), Work (Trabajo) o Public
location (Ubicacin pblica).
Seleccione la ubicacin de red
L.
Esta pantalla vara segn la ubicacin seleccionada. Haga clic en
Close (Cerrar).
Parmetros de red guardados
M. El icono de la utilidad de
configuracin de red inalmbrica de Windows Vista aparecer en la
bandeja del sistema del escritorio.Icono de la utilidad de
configuracin de red inalmbrica de Windows Vista
Puede utilizar esta utilidad para configurar o cambiar sus
parmetros inalmbricos.
Estado de la conexin inalmbrica
NOTA: Para obtener ayuda con la utilidad de configuracin de red
inalmbrica de Windows Vista, consulte la ayuda y soporte tcnico de
Windows Vista haciendo clic en el botn Inicio > Ayuda y soporte
tcnico. Enhorabuena. La configuracin ha finalizado.
Para obtener informacin adicional o ayuda para la resolucin de
problemas, consulte la gua del usuario proporcionada en el CD-ROM.
Tambin puede obtener asistencia por correo electrnico o por
telfono. Sitio Web http://www.linksys.eu Registro de productos
http://www.linksys.com/registration
Linksys es una marca registrada o marca comercial de Cisco
Systems, Inc. o sus filiales en EE.UU. y otros pases. Copyright
2007 Cisco Systems, Inc. Todos los derechos reservados. Otras
marcas y nombres de productos son marcas comerciales o marcas
registradas de sus respectivos propietarios. 70517NC-JL
INSTALLATION RAPIDE
Adaptateur PCI sans fil - GINSTRUCTIONS POUR LES UTILISATEURS DE
WINDOWS VISTA UNIQUEMENT
Contenu de lemballage
Adaptateur PCI sans fil - G ou Adaptateur PCI sans fil - G avec
SpeedBooster ou Adaptateur PCI sans fil - G avec RangeBooster
CD-ROM de lAssistant de configuration Guide de lutilisateur
disponible sur CD-ROM Installation rapide
Modle : WMP54G
WMP54GS WMP54GR
1
InstallationLAssistant de configuration disponible sur le CD
dinstallation fourni permet dinstaller et de configurer
ladaptateur. Ce Guide dinstallation rapide sadresse uniquement aux
utilisateurs de Windows Vista. Si vous utilisez Windows XP ou 2000,
utilisez lautre Guide dinstallation rapide fourni. IMPORTANT :
Ninstallez pas ladaptateur sur votre ordinateur avant dy avoir t
invit, sinon ladaptateur ne sera pas correctement install.
A.
Insrez le CD de lAssistant de configuration dans le lecteur de
CD-ROM.
Insrez le CD-ROM
REMARQUE : Windows Vista ou un autre de vos pare-feu peuvent
vous demander lautorisation dexcuter le logiciel ou le programme.
Pour continuer, vous devez autoriser lexcution du logiciel.
B.
Lcran Welcome (Bienvenue) saffiche. Cliquez sur le bouton Click
Here to Start (Cliquez ici pour dmarrer).
Cliquez ici pour dmarrer
C.
Lisez laccord de licence, puis cliquez sur Next (Suivant) pour
continuer linstallation.
Accord de licence
D.1. 2.
Suivez les instructions ci-aprs pour installer physiquement
ladaptateur : Mettez lordinateur hors tension. Aprs linstallation
de ladaptateur, selon la description ci-dessous, et le redmarrage
de lordinateur, lAssistant de con guration poursuit la procdure.
Ouvrez le botier de lordinateur et recherchez un connecteur PCI
disponible sur la carte mre. Pour plus dinstructions, adressez-vous
au fabricant de votre ordinateur.
Installation de ladaptateur
3. 4. 5. 6.
Faites glisser ladaptateur dans le connecteur. Assurez-vous que
toutes ses broches sont en ches dans le connecteur. Pour ce faire,
appuyez lgrement sur ladaptateur, si ncessaire, a n de lenfoncer
compltement. Fixez sa tige mtallique sur le chssis de lordinateur
laide dune vis. Refermez le botier de lordinateur. Mettez
lordinateur sous tension et passez ltape E.
E.
Aprs avoir install ladaptateur correctement, lcran
Congratulations (Flicitations) saffiche. Cliquez sur Finish
(Terminer).
Flicitations
F.
Le premier cran de lutilitaire de configuration automatique de
rseau sans fil de Windows Vista saffiche. Slectionnez votre rseau,
puis cliquez sur Se connecter.
Slection du rseau
G.
Si la scurit sans fil de votre rseau est dsactive, lcran
ci-contre saffiche. Si la scurit sans fil est active sur votre
rseau, passez ltape H. Pour vous connecter votre rseau non scuris,
cliquez sur Je confirme la demande de connexion, puis passez ltape
I.
Rseau non scuris
H.
Si la scurit sans fil de votre rseau est active, lcran ci-contre
saffiche. Saisissez la cl de scurit ou la phrase de passe (que lon
appelle galement cl pr-partage ou cl WEP, selon votre type de
scurit). Cliquez sur Connexion.Rseau scuris
I.
Lcran ci-contre saffiche pendant que ladaptateur se connecte
votre rseau. Ne cliquez pas sur annuler, sauf si vous souhaitez
interrompre linstallation.
Connexion au rseau
J.
Lcran ci-contre saffiche lorsque vous tes connect votre rseau.
Cliquez sur Enregistrer ce rseau, si vous souhaitez enregistrer vos
paramtres. Cliquez sur Fermer.Connect au rseau
K.
Lcran Dfinir un emplacement rseau saffiche. Il vous permet
dappliquer les paramtres appropris votre type demplacement. Sil ne
saffiche pas, passez ltape M. Slectionnez Domicile, Bureau ou Lieu
public.
Slection de lemplacement du rseau
L.
Lcran ci-contre varie selon lemplacement que vous avez
slectionn. Cliquez sur Fermer.
Paramtres rseau enregistrs
M. Licne de lutilitaire de
configuration automatique de rseau sans fil de Windows Vista
saffiche dans la barre dtat systme de votre bureau.
Icne de lutilitaire de configuration automatique de rseau sans
fil de Windows Vista.
Vous pouvez utiliser cet utilitaire pour configurer ou modifier
vos paramtres sans fil.
Etat de la connexion sans fil
REMARQUE : Pour recevoir de laide propos de lutilitaire de
configuration automatique de rseau sans fil de Windows Vista,
reportez-vous la rubrique Aide et support de Windows Vista, en
cliquant sur licne Dmarrer de Vista > Aide et Support.
Flicitations ! La configuration est termine.
Pour obtenir de plus amples informations ou une assistance
technique, reportez-vous au Guide de lutilisateur figurant sur le
CD-ROM dinstallation. Vous pouvez recevoir une assistance
complmentaire par e-mail ou par tlphone. Site Web :
http://www.linksys.eu Enregistrement du produit :
http://www.linksys.com/registration
Linksys est une marque dpose ou une marque commerciale de Cisco
Systems, Inc. et/ou de ses filiales aux Etats-Unis et dans certains
autres pays. Copyright 2007 Cisco Systems, Inc. Tous droits rservs.
Les autres noms de marques et de produits sont des marques ou
marques dposes de leurs dtenteurs respectifs. 70517NC-JL
INSTALLAZIONE RAPIDA
Adattatore PCI Wireless-GISTRUZIONI RIVOLTE ESCLUSIVAMENTE AGLI
UTENTI DI WINDOWS VISTA
Contenuto della confezione
Adattatore PCI Wireless-G o Adattatore PCI Wireless-G con
SpeedBooster o Adattatore PCI Wireless-G con RangeBooster CD-ROM
per linstallazione guidata Guida per lutente su CD-ROM Guida di
installazione rapida
Modello:
WMP54G WMP54GS WMP54GR
1
InstallazioneLadattatore viene installato e configurato
utilizzando la procedura di installazione guidata fornita nel CD
per linstallazione guidata accluso. La presente Guida di
installazione rapida rivolta solo agli utenti di Windows Vista. Se
il sistema operativo utilizzato Windows XP o 2000, utilizzare
laltra Guida di installazione rapida acclusa. IMPORTANTE: non
installare ladattatore nel computer finch non viene richiesto; in
caso contrario, ladattatore non verr installato correttamente.
A.
Inserire il CD per linstallazione guidata nellunit CD-ROM.
Inserire il CD-ROM
NOTA: il firewall di Windows Vista o altri firewall personali
potrebbero chiedere lautorizzazione a eseguire il software o il
programma. Per continuare necessario concedere lautorizzazione.
B.
Sul monitor viene visualizzata la schermata Welcome (Benvenuti).
Fare clic sul pulsante Click Here to Start (Fare clic qui per
iniziare).
Fare clic qui per iniziare
C.
Leggere il contratto di licenza e fare clic su Next (Avanti) per
proseguire linstallazione. Per linstallazione fisica delladattatore
procedere come segue: Spegnere il computer. Dopo aver installato
ladattatore, come mostrato di seguito, e riavviato il computer,
linstallazione guidata continuer. Aprire il case del computer e
individuare uno slot PCI libero sulla scheda madre. Per istruzioni
al riguardo, consultare il materiale di riferimento fornito dal
produttore del computer.
D.1.
Contratto di licenza
2.
Installazione delladattatore
3.
Inserire ladattatore nello slot. Assicurarsi che tutti i piedini
tocchino i contatti dello slot. Potrebbe essere necessaria una
leggera pressione per inserire fino in fondo ladattatore. Fissarlo
al telaio del computer con una vite. Chiudere il case. Accendere il
computer e passare alla fase E.
4. 5. 6.
E.
Dopo avere installato correttamente ladattatore, viene
visualizzata la schermata Congratulations (Congratulazioni). Fare
clic su Finish (Fine).
Congratulazioni
F.
Viene visualizzata la prima schermata dellutilit per la
configurazione di rete wireless di Windows Vista. Selezionare la
propria rete, quindi fare clic su Connetti.
Selezione della rete
G.
Se la rete non dispone di protezione wireless, viene
visualizzata la schermata illustrata a fianco. Se invece la rete
dispone di protezione wireless, passare alla fase H. Per collegarsi
comunque alla rete non protetta, fare clic su Connetti comunque e
passare alla fase I.Rete non protetta
H.
Se la rete dispone di protezione wireless, viene visualizzata la
schermata illustrata a fianco. Immettere la chiave di sicurezza o
la passphrase (nota anche come chiave precondivisa o chiave WEP, in
base al tipo di protezione). Fare clic su Connetti.Rete
protetta
I.
Mentre ladattatore si collega alla rete, viene visualizzata la
schermata illustrata a fianco. Non fare clic su Annulla, a meno che
non si desideri terminare linstallazione.
Connessione alla rete in corso
J.
A connessione ultimata viene visualizzata la schermata
illustrata a fianco. Selezionare Salva questa rete per salvare le
impostazioni. Fare clic su Chiudi.Connesso alla rete
K.
La schermata Impostazioni rete potrebbe essere visualizzata per
suggerire le corrette impostazioni per il tipo di percorso. Se ci
non accade, passare alla fase M. Selezionare Abitazione, Ufficio o
Luogo pubblico.
Selezione del percorso di rete
L.
Questa schermata varia in base al percorso selezionato. Fare
clic su Chiudi.
Impostazioni di rete salvate
M. Licona dellutilit per laconfigurazione di rete wireless di
Windows Vista compare sulla barra delle applicazioni del
desktop.Icona dellutilit per la configurazione di rete wireless di
Windows Vista
Lutilit pu essere usata per configurare o modificare le
impostazioni wireless.
Stato della connessione wireless
NOTA: per assistenza relativa allutilit per la configurazione di
rete wireless di Windows Vista, accedere alla sezione Guida in
linea e supporto tecnico di Windows Vista, facendo clic sul
pulsante Start > Guida in linea e supporto tecnico.
Congratulazioni! La configurazione stata completata.
Per ulteriori informazioni o istruzioni relative alla
risoluzione dei problemi, consultare la Guida per lutente sul
CD-ROM. possibile ottenere ulteriore assistenza tramite e-mail o
telefonicamente. Sito Web http://www.linksys.eu Registrazione del
prodotto http://www.linksys.com/registration
Linksys un marchio o marchio registrato di Cisco Systems, Inc.
e/o delle relative aziende affiliate negli Stati Uniti e in altri
Paesi. Copyright 2007 Cisco Systems, Inc. Tutti i diritti
riservati. Altri marchi e nomi di prodotti sono marchi o marchi
registrati dei rispettivi proprietari. 70517NC-JL
INSTALLATIEHANDLEIDING
Wireless-G PCIadapterINSTRUCTIES ALLEEN VOOR GEBRUIKERS VAN
WINDOWS VISTA
Inhoud van de verpakking
Wireless-G PCI-adapter of Wireless-G PCI-adapter met
SpeedBooster of Wireless-G PCI-adapter met RangeBooster Cd-rom met
Setup Wizard (Installatiewizard) Gebruikershandleiding op cd-rom
Installatiehandleiding
Model:
WMP54G WMP54GS WMP54GR
1
InstallatieDe adapter wordt genstalleerd en ingesteld aan de
hand van de Setup Wizard (Installatiewizard) op de meegeleverde
cd-rom. Deze installatiehandleiding is alleen voor gebruikers van
Windows Vista bedoeld. Als u Windows XP of 2000 gebruikt, dient u
de andere meegeleverde installatiehandleiding te gebruiken.
BELANGRIJK: sluit de adapter pas aan op uw computer als u hiervoor
de instructie krijgt, anders wordt de adapter niet correct
genstalleerd.
A.
Plaats de cd-rom met de Setup Wizard (Installatiewizard) in het
cdromstation van uw computer.
De cd-rom plaatsen
OPMERKING: bij Windows Vista of andere persoonlijke rewalls
wordt mogelijk uw toestemming gevraagd voor het uitvoeren van de
software of het programma. Als u verder wilt gaan, dient u
toestemming te geven voor het uitvoeren van de software.
B.
Het scherm Welcome (Welkom) wordt weergegeven op uw monitor.
Klik op de knop Click Here to Start (Klik hier om te beginnen).
Click here to start (Klik hier om te beginnen)
C.
Lees de licentieovereenkomst en klik op Next (Volgende) om
verder te gaan met de installatie.
Licentieovereenkomst
D.1. 2.
Volg de instructies om de adapter fysiek te installeren: Schakel
uw computer uit. Als u de adapter hebt genstalleerd, zoals
hieronder beschreven, en uw computer opnieuw hebt opgestart, gaat
de Setup Wizard (Installatiewizard) verder. Maak de behuizing van
uw computer open en kijk of er een PCI-sleuf beschikbaar is op het
moederbord. Neem voor verdere instructies contact op met de
fabrikant van uw computer.
Install the Adapter (Adapter installeren)
3. 4. 5. 6.
Steek de adapter in de sleuf. Controleer of alle pennen van de
adapter contact maken met de sleufcontactpunten. Er kan enige
kracht nodig zijn om de adapter helemaal in de sleuf te duwen. Zet
de bevestigingstab met een schroef vast aan het computerframe. Maak
de behuizing van uw computer weer dicht. Schakel uw computer in en
ga verder met stap E.
E.
Nadat u de adapter correct hebt aangesloten, wordt het scherm
Congratulations (Gefeliciteerd) weergegeven. Klik op Finish
(Voltooien).
Congratulations (Gefeliciteerd)
F.
Het eerste Windows Vistahulpprogrammascherm voor het
configureren van een draadloos netwerk wordt weergegeven. Selecteer
uw netwerk en klik vervolgens op Connect (Verbinding maken).
Netwerk selecteren
G.
Als uw netwerk niet over draadloze beveiliging beschikt, wordt
dit scherm weergegeven. Als uw netwerk wel over draadloze
beveiliging beschikt, gaat u verder met stap H. Als u verbinding
wilt maken met uw onbeveiligde netwerk, klikt u op Connect Anyway
(Toch verbinding maken) en gaat u vervolgens verder met stap I.
Onbeveiligd netwerk
H.
Als uw netwerk over draadloze beveiliging beschikt, wordt dit
scherm weergegeven. Voer de beveiligingssleutel of wachtzin in
(afhankelijk van het type beveiliging ook wel vooraf gedeelde
sleutel of WEP-sleutel genoemd). Klik op Connect (Verbinding
maken).Beveiligd netwerk
I.
Dit scherm wordt weergegeven terwijl de adapter verbinding maakt
met uw netwerk. Klik niet op Cancel (Annuleren) tenzij u de
installatie wilt beindigen.
Verbinding maken met netwerk
J.
Dit scherm wordt weergegeven wanneer de verbinding met uw
netwerk tot stand is gebracht. Selecteer Save this Network (Dit
netwerk opslaan) als u uw instellingen wilt opslaan. Klik op Close
(Sluiten).Verbonden met netwerk
K.
Mogelijk wordt het scherm Set Network Location (Netwerklocatie
instellen) weergegeven om u te helpen bij het toepassen van de
juiste instellingen voor uw type locatie. Als het scherm niet wordt
weergegeven, gaat u verder met stap M. Selecteer Home (Thuis), Work
(Werk) of Public location (Openbare locatie).
Netwerklocatie selecteren
L.
Afhankelijk van de geselecteerde locatie kan dit scherm er
anders uitzien. Klik op Close (Sluiten).
Netwerkinstellingen opgeslagen
M. Het Windows Vista-
hulpprogrammapictogram voor het configureren van een draadloos
netwerk wordt weergegeven in het systeemvak op het bureaublad.
Windows Vista-hulpprogrammapictogram voor het configureren van
een draadloos netwerk
U kunt met dit hulpprogramma de instellingen voor uw draadloze
netwerk configureren of wijzigen.
Status van draadloze verbinding
OPMERKING: Raadpleeg de Help en ondersteuning van Windows Vista
als u hulp nodig hebt met het Windows Vistahulpprogramma voor het
Configureren van een draadloos netwerk. Klik hiervoor op de
Vista-knop Start ondersteuning. > Help en
Gefeliciteerd! De installatie is voltooid.
Raadpleeg voor meer informatie of voor probleemoplossing de
gebruikershandleiding op de cd-rom. Aanvullende ondersteuning is
ook beschikbaar per telefoon of e-mail. Website
http://www.linksys.eu Productregistratie:
http://www.linksys.com/registration
Linksys is een gedeponeerd handelsmerk van Cisco Systems, Inc.
en/of zijn dochterondernemingen in de VS en bepaalde andere landen.
Copyright 2007 Cisco Systems, Inc. Alle rechten voorbehouden.
Andere merken en productnamen zijn handelsmerken of gedeponeerde
handelsmerken van de respectieve houders. 70517NC-JL
INSTALAO RPIDA
Placa PCI sem fios G
INSTRUES APENAS PARA UTILIZADORES DO WINDOWS VISTA
Contedo da embalagem
Placa PCI sem fios G ou Placa PCI sem fios G com SpeedBooster ou
Placa PCI sem fios G com RangeBooster CD-ROM do Setup Wizard
(Assistente de configurao) CD-ROM com Manual do Utilizador Instalao
Rpida
Modelo:
WMP54G WMP54GS WMP54GR
1
InstalaoA Placa instalada e configurada utilizando o Setup
Wizard (Assistente de configurao) includo no CD fornecido. Esta
Instalao Rpida destina-se apenas a utilizadores do Windows Vista.
Se tiver o Windows XP ou 2000, utilize a outra Instalao Rpida
fornecida. IMPORTANTE: No instale a Placa no computador at receber
instrues para o fazer, pois, caso contrrio, a Placa no ser
instalada correctamente.
A.
Coloque o CD do Setup Wizard (Assistente de configurao) na
unidade de CD-ROM.
Colocar o CD-ROM
NOTA: O Windows Vista ou outras rewalls pessoais podero
solicitar permisso para executar o software ou programa. Para
continuar, tem de permitir a execuo do software.
B.
O ecr Welcome (Bem-vindo) apresentado no monitor. Clique no boto
Click Here to Start (Clique aqui para iniciar).
Click Here to Start (Clique aqui para iniciar)
C.
Leia o License Agreement (Contrato de licena) e clique em Next
(Seguinte) para prosseguir com a instalao.
License Agreement (Contrato de licena)
D.1. 2.
Siga as instrues para instalar fisicamente a Placa: Desligue o
computador. Depois de instalar a Placa, como descrito abaixo, e de
reiniciar o computador, o Setup Wizard (Assistente de con gurao)
continuar. Abra a tampa do computador e localize uma ranhura PCI
disponvel na placa de sistema. Consulte o fabricante do computador
para obter instrues.
Instalar a placa
3. 4. 5. 6.
Introduza a Placa na ranhura. Certi que-se de que todos os pinos
esto em contacto com a ranhura. Poder ser necessrio pressionar
ligeiramente a Placa para a encaixar completamente. Fixe a patilha
ao chassis do computador com um parafuso de montagem. Feche a tampa
do computador. Ligue o computador e avance para o passo E.
E.
Depois de instalar correctamente a Placa, apresentado o ecr
Congratulations (Parabns). Clique em Finish (Concluir).
Congratulations (Parabns)
F.
apresentado o primeiro ecr do utilitrio Configurao da Rede Sem
Fios do Windows Vista. Seleccione a rede e, em seguida, clique em
Ligar.
Seleccionar rede
G.
Se a rede no tiver segurana sem fios, ser apresentado este ecr.
Se a rede tiver segurana sem fios, v para o passo H. Para
estabelecer ligao rede insegura, clique em Ligar Assim Mesmo e v
para o passo I.Rede insegura
H.
Se a rede tiver segurana sem fios, ser apresentado este ecr.
Introduza a chave de segurana ou frase-passe (tambm conhecida como
chave pr-partilhada ou chave WEP, consoante o tipo de segurana).
Clique em Ligar.Rede segura
I.
apresentado este ecr enquanto a Placa ligada rede. No cancele a
operao, a menos que pretenda terminar a instalao.
A ligar rede
J.
apresentado este ecr quando estiver ligado rede. Seleccione
Guardar esta rede, se pretender guardar as definies. Clique em
Fechar.
Ligado rede
K.
Poder ser apresentado o ecr Definir Localizao de Rede para
ajudar a aplicar as definies correctas para o tipo de localizao. Se
no for apresentado, v para o passo M. Seleccione Casa, Trabalho ou
Local pblico.
Seleccionar localizao de rede
L.
Este ecr varia consoante a localizao seleccionada. Clique em
Fechar.
Definies da rede guardadas
M. O cone do utilitrio Configurao
da Rede Sem Fios do Windows Vista apresentado no tabuleiro do
sistema do ambiente de trabalho.
cone do utilitrio Configurao da Rede Sem Fios do Windows
Vista
Pode usar este utilitrio para configurar ou alterar as definies
sem fios.
Estado da ligao sem fios
NOTA: Para obter ajuda para o utilitrio Configurao da Rede Sem
Fios do Windows Vista, consulte a Ajuda e Suporte do Windows Vista
clicando no boto Iniciar do Vista > Ajuda e Suporte.
Parabns! A configurao est concluda.
Para obter informaes adicionais ou ajuda para resoluo de
problemas, consulte o Manual do Utilizador no CD-ROM. Tambm se
encontra disponvel suporte adicional por correio electrnico ou por
telefone. Web site: http://www.linksys.eu Registo do produto:
http://www.linksys.com/registration
Linksys uma marca registada ou marca comercial da Cisco Systems,
Inc. e/ou das respectivas afiliadas nos E.U.A. e noutros pases.
Copyright 2007 Cisco Systems, Inc. Todos os direitos reservados.
Outras marcas e nomes de produtos so marcas comerciais ou marcas
registadas dos respectivos proprietrios. 70517NC-JL
INSTALAO RPIDA
Adaptador PCI Wireless-GINSTRUES APENAS PARA USURIOS DO WINDOWS
VISTA
Contedo da embalagem
Adaptador PCI Wireless-G ou Adaptador PCI Wireless-G com
SpeedBooster ou Adaptador PCI Wireless-G com RangeBooster CD-ROM do
Assistente para configurao Guia do usurio no CD-ROM Instalao
rpida
Modelo:
WMP54G WMP54GS WMP54GR
1 InstalaoO Adaptador instalado e configurado usando o
Assistente para configurao includo no CD do Assistente para
configurao fornecido. Esta Instalao rpida destina-se apenas aos
usurios do Windows Vista. Se voc tiver o Windows XP ou 2000, use a
outra Instalao rpida fornecida. IMPORTANTE: no instale o Adaptador
no computador at ser instrudo a fazer isso, ou o Adaptador no ser
instalado corretamente.
A.
Insira o CD do Assistente para configurao em sua unidade de
CD-ROM.
Insira o CD-ROM
OBSERVAO: o firewall do Windows Vista ou outros firewalls
pessoais podem solicitar permisso para executar o software ou o
programa. Voc dever permitir que o software seja executado a fim de
continuar.
B.
A tela Welcome (Bem-vindo) ser exibida no monitor. Clique no
boto Click Here to Start (Clique aqui para iniciar).
Click Here to Start
C.
Leia o Contrato de licena e clique em Next (Avanar) para
continuar a instalao.
License Agreement
D.1. 2.
Siga as instrues para instalar fisicamente o Adaptador: Desligue
o computador. Aps a instalao do Adaptador, como mostrado a seguir,
e a reinicializao do computador, o Assistente para configurao
continuar. Abra o gabinete do computador e localize um slot PCI
disponvel na placa-me. Obtenha as instrues com o fabricante de seu
computador.
Instalao do Adaptador
3. 4. 5. 6.
Deslize o Adaptador para dentro do slot. Certifique-se de que
todos os pinos estejam em contato com o slot. Talvez seja necessrio
aplicar um pouco de presso para deslizar totalmente o Adaptador.
Fixe sua presilha ao chassi do computador com um parafuso de
montagem. Feche o gabinete do computador. Ligue o computador e
continue na etapa E.
E.
Aps a instalao correta do Adaptador, a tela Congratulations
(Parabns) exibida. Clique em Finish (Concluir).
Congratulations
F.
A primeira tela do utilitrio de configurao de rede sem fio do
Windows Vista exibida. Selecione a sua rede e clique em
Conectar.
Seleo da rede
G.
Se a sua rede no possuir segurana sem fio, esta tela ser
exibida. Se a sua rede possuir segurana sem fio, v para a etapa H.
Para conectar-se sua rede no segura, clique em Conectar assim mesmo
e v para a etapa I.Rede no segura
H.
Se a sua rede possuir segurana sem fio, esta tela ser exibida.
Insira a chave de segurana ou a senha (tambm conhecida como chave
pr-compartilhada ou chave WEP, dependendo do tipo de segurana).
Clique em Conectar.Rede segura
I.
Esta tela ser exibida enquanto o Adaptador se conecta sua rede.
No cancele, a menos que deseje encerrar a instalao.
Conectando-se rede
J.
Esta tela exibida quando voc conectado sua rede. Selecione
Salvar esta rede se desejar salvar suas configuraes. Clique em
Fechar.
Conectado rede
K.
A tela Definir local da rede pode ser exibida para ajudar na
aplicao das configuraes corretas de seu tipo de local. Se ela no
for exibida, v para a etapa M. Selecione um local residencial,
comercial ou pblico.
Seleo do local de rede
L.
Esta tela varia de acordo com o local selecionado. Clique em
Fechar.
Configuraes de rede salvas
M. O cone do utilitrio de configuraode rede sem fio do Windows
Vista exibido na bandeja do sistema de sua rea de trabalho.cone do
utilitrio de configurao de rede sem fio do Windows Vista
Voc pode usar esse utilitrio para configurar ou alterar suas
configuraes sem fio.
Status da conexo sem fio
OBSERVAO: para obter ajuda com o utilitrio de configurao de rede
sem fio do Windows Vista, consulte a Ajuda e Suporte do Windows
Vista clicando no boto Iniciar do Windows Vista Ajuda e suporte.
Parabns! A configurao foi concluda. >
Para obter informaes adicionais ou ajuda na resoluo de
problemas, consulte o Guia do usurio no CD-ROM. Tambm h suporte
adicional disponvel por email ou telefone. Website
http://www.linksys.com/br Registro do produto:
http://www.linksys.com/br/registration
Linksys marca registrada ou comercial da Cisco Systems, Inc.
e/ou de suas afiliadas nos Estados Unidos e em outros pases.
Copyright 2007 Cisco Systems, Inc. Todos os direitos reservados.
Outras marcas e nomes de produtos so marcas registradas ou
comerciais de seus respectivos proprietrios. 70517NC-JL
SNABBINSTALLATION
Wireless-G PCI-adapter
INSTRUKTIONER FR WINDOWS VISTA ENDAST ANVNDARE
Innehll i frpackningen
Wireless-N PCI-adapter eller Wireless-G PCI-adapter med
SpeedBooster eller Wireless-G PCI-adapter med RangeBooster Cd-skiva
med installationsguide Anvndarhandbok p cd-skiva
Snabbinstallation
Modell:
WMP54G WMP54GS WMP54GR
1 InstallationAdaptern installeras och konfigureras med hjlp av
installationsguiden p den medfljande cd-skivan. Snabbinstallationen
gller endast fr Windows Vista-anvndare. Om du har Windows XP eller
2000 anvnder du den andra medfljande snabbinstallationen. VIKTIGT!
Installera inte adaptern i datorn frrn du fr en uppmaning om att
gra det i steg 2. I annat fall installeras inte adaptern som den
ska.
A.
Stt in cd-skivan med installationsguiden i cd-enheten.
Stt i cd-skivan
OBS! Windows Vista eller andra personliga brandvggar kan be om
tillstnd fr att kra programvaran eller programmet. Du mste tillta
att programvaran krs fr att kunna fortstta.
B.
Skrmen Welcome (Vlkommen) visas p bildskrmen. Klicka p knappen
Click Here to Start (Klicka hr om du vill starta).
Klicka hr om du vill starta
C. D.1.
Ls igenom licensavtalet och klicka p Next (Nsta) om du vill
fortstta med installationen. Flj instruktionerna om du fysiskt vill
installera adaptern: Stng av datorn. Nr du har installerat adaptern
p det stt som anges nedan och startat om datorn fortstter
installationsguiden. ppna datorchassit och leta rtt p en ledig
PCI-kortplats p moderkortet. Kontakta datortillverkaren fr
anvisningar.
Licensavtal
2.
Installera adaptern
3. 4. 5. 6.
Skjut in adaptern p kortplatsen. Se till att alla stift vidrr
kontaktytorna i kortplatsen. Du kan behva anvnda viss kraft fr att
skjuta in adaptern hela vgen. Montera fstanordningen p datorchassit
med hjlp av en skruvmejsel. Stng datorchassit. Stt p datorn och g
vidare till steg E.
E.
Nr du har installerat adaptern p rtt stt visas skrmen
Congratulations (Klart). Klicka p Finish (Slutfr).
Klart!
F.
Den frsta skrmen fr trdls ntverkskonfiguration fr Windows Vista
visas. Vlj ntverk och klicka sedan p Connect (Anslut).
Vlj ntverk
G.
Om ntverket saknar trdls skerhet visas den hr skrmen. Om
ntverket har trdls skerhet gr du till steg H. Om du vill ansluta
det oskyddade ntverket klickar du p Connect Anyway (Anslut nd) och
gr till steg I.Oskyddat ntverk
H.
Om ntverket har trdls skerhet visas den hr skrmen. Ange
skerhetsnyckel eller lsenordsfras (kallas ven fr-delad nyckel eller
WEP-nyckel, beroende p din typ av skerhet). Klicka p Connect
(Anslut).Skyddat ntverk
I.
Den hr skrmen visas nr adaptern ansluts till ntverket. Avbryt
inte anslutningen svida du inte vill avsluta installationen.
Ansluter till ntverk
J.
Skrmen visas nr du r ansluten till ntverket. Vlj Save this
network (Spara det hr ntverket) om du vill spara ndringarna. Klicka
p Close (Stng).Ansluten till ntverk
K.
Skrmen Set Network Location (Ange ntverksplats) visas eventuellt
fr att du ska kunna anvnda rtt instllningar fr din typ av plats. Om
den inte visas gr du till steg M. Vlj Home, (Hemma) Work (Arbete)
eller Public location (Offentlig plats).Vlj ntverksplats
L.
Den hr skrmen varierar beroende p vald placering. Klicka p Close
(Stng).
Sparade ntverksinstllningar
M. Ikonen fr verktyget fr trdls
ntverkskonfiguration fr Windows Vista visas i skrivbordets
systemflt.Ikonen fr verktyget fr trdls ntverkskonfiguration fr
Windows Vista.
Verktyget kan anvndas fr att konfigurera eller ndra de trdlsa
instllningarna.
Status fr trdls anslutning
OBS! Om du vill ha hjlp med verktyget fr trdls
ntverkskonfiguration fr Windows Vista lser du i hjlpen och
supporten fr Windows Vista genom att klicka p Vistas Start-knapp
och Support). Klart! Installationen r slutfrd. > Help and
Support (Hjlp
Mer information samt felskningshjlp finns i anvndarhandboken p
cd-skivan. Du kan ocks f mer hjlp via e-post eller telefon.
Webbplats http://www.linksys.eu Produktregistrering
http://www.linksys.com/registration
Linksys r ett registrerat varumrke eller ett varumrke som tillhr
Cisco Systems, Inc. och/eller dess samarbetspartner i USA och i
vissa andra lnder. Copyright 2007 Cisco Systems, Inc. Med ensamrtt.
Andra varumrken och produktnamn r varumrken eller registrerade
varumrken som tillhr respektive gare. 70517NC-JL
Package Contents Wireless-G PCI Adapter One Setup CD-ROM One
User Guide on CD-ROM Quick Installation Guide
2,4GHz Wireless-G802.11g
PCI Adapter
Wireless
Quick Installation Guide1
Model No.
WMP54G (EU/LA)
1
Begin Installation
IMPORTANT: Do not install the Adapter in your PC until you are
instructed to do so in Step 2 or the Adapter will not install
correctly.The PCI Adapter is installed and set up using the Setup
Wizard that comes on the CD enclosed.
A
To begin, insert the Setup Wizard CD-ROM into your CDROM drive.
The Setup Wizard should run automatically, and the Welcome screen
should appear. If asked to select a language, select an available
language from the drop down menu. Then click install. To install
the Adapter, click Click Here to Start on the Welcome screen. After
reading the License Agreement, click Next to continue the
installation and Windows will begin copying the files onto your PC.
The Setup Wizard will now prompt you to install the Adapter into
your PC. Click Next and your PC will power down. Proceed to Step
2.
B
B C
C
D
2
2
Connect the Adapter
IMPORTANT: Make sure to turn off the power to your PC, and
unplug the power cord, before opening the case to prevent possible
electrical shock to you or damage to the PC.
A B
Before connecting the PCI Adapter to your PC, make sure that
your desktop PC is powered down. Open your PC case and locate an
available PCI slot on the motherboard. Check with your computer
manufacturer for instructions. Slide the PCI Adapter into the PCI
slot. Make sure that all of its pins are touching the slot's
contacts. You may have to apply a bit of pressure to slide the
adapter all the way in. After the adapter is firmly in place,
secure its fastening tab to your PC's chassis with a mounting
screw. Then, close your PC. Attach the external antenna to the
adapters antenna port. Power on your desktop PC. Proceed to Step
3.
Connecting the Adapter
C
Installing the Adapter
D E
Positioning the Antenna3
3
Set Up the Adapter
The next screen to appear will be the Available Wireless Network
screen. From this screen, you can launch one of the three setup
methods.IMPORTANT: For Quick Installation, use
this document only if your network appears on the Available
Wireless Network screen.SecureEasySetup: If you are utilitizing
SecureEasySetup, click the SecureEasySetup button and follow the on
screen prompts. Manual Setup: If you are utilitizing Manual Setup,
click the Manual Setup button and follow the on screen prompts.
Available Wireless Network
Setting Up the Adapter with Available NetworksOn the Available
Wireless Network screen, the available networks are listed in the
center table by SSID. Select the wireless network you wish to
connect to and click the Connect button. (If you do not see your
network listed, you can click the Refresh button.) If the network
utilizes wireless security, you will need to configure security on
the Adapter. If not, you will be taken directly to the
Congratulations screen, shown in Step B.
4
A
If wireless security has been enabled on this network, you will
see a wireless security screen. If your network utilizes WEP (Wired
Equivalent Privacy) encryption, the WEP Key Needed for Connection
screen will appear. If your network utilizes WPA Personal (Wi-Fi
Protected Access), the WPA Personal Needed for Connection screen
will appear. If your network utilizes PSK2 (Pre-Shared Key 2)
encryption, the PSK2 Needed for Connection screen will appear. WEP
Key Needed for Connection Select 64-bit or 128-bit. Then, enter a
passphrase or WEP key. Passphrase - Enter a passphrase in the
Passphrase field. This is casesensitive and should not be longer
than 16 alphanumeric characters. It must match the passphrase of
your other wireless network devices and is compatible with Linksys
wireless products only. (Non-Linksys wireless products, require a
WEP key to be entered.) WEP Key - The WEP key must match the WEP
key of your wireless network. For 64-bit encryption, enter exactly
10 hexadecimal characters. For 128-bit encryption, enter exactly 26
hexadecimal characters. Valid hexadecimal characters are 0 to 9 and
A to F. Then, click Connect and proceed to Step B.
WEP Key Needed
5
WPA Personal Needed for Connection Encryption - Select the type
of algorithm you want to use, TKIP or AES, from the Encryption
dropdown menu. Passphrase - Enter a Passphrase of 8-63 characters
in the Passphrase field. The longer and more complex your
Passphrase is, the more secure your network will be. Click Connect
and go to Step B. PSK2 Needed for Connection Enter a Passphrase of
8-63 characters in the Passphrase field. Click Connect and go to
Step B.
WPA Personal Needed
B
After the Adapter has been configured for the network, the
Congratulations screen will appear. Click Connect to Network to
connect to your network. Congratulations! Setup is complete.
PSK2 Needed
NOTE: After the Adapter is installed, the Wire-
less Network Monitor screen will open and its icon will appear
in your PCs system tray. Double-click the icon if you want to open
the Wireless Network Monitor for finding available wireless
networks or making additional configuration changes.
Wireless Network Monitor icon6
Setting Up the Adapter with Secure Easy SetupWith Secure Easy
Setup, setting up the Adapter is as simple as pushing a couple of
buttons. Before you press any buttons, though, you should locate
the Secure Easy Setup button on the device youre connecting the
Adapter to, such as a wireless router or access point.
Available Wireless Network
A
Secure Easy Setup button on the right hand side.
Starting from the Available Wireless Network screen, click
the
B
You will be asked to locate the Secure Easy Setup button on the
device with which the Adapter will be communicating. If you are not
sure where to find this button, click Where can I find the
button?
Where can I find the button?
This will walk you through a couple of screens to help you find
the button, which is usually located on the front of the wireless
router or access point.
Secure Easy Setup Logo And Location7
C
Press the Cisco logo or Secure Easy Setup button on the wireless
router or access point. When it turns white and begins to flash,
click the Next button on the Setup Wizard screen. The logo or
button will stop flashing on the wireless router or access point
when the Adapter has been successfully added to the network. Repeat
this procedure for any additional Secure Easy Setup device.
D
When Secure Easy Setup is complete, you may save your
configuration to a text file by clicking the Save button, or print
the configuration by clicking the Print button. Click Connect to
Network to connect to your network.Congratulations! Setup is
complete.
Congratulations
8
4
Using the Wireless Network MonitorNOTE: The Wireless Network
Monitor should only be accessed AFTER installing the Adapter.
Use the Wireless Network Monitor to check the link information,
search for available wireless networks, or create profiles that
hold different configuration settings.
Accessing the Wireless Network MonitorAfter setting up and
connecting the Adapter, the Wireless Network Monitor icon will
appear in your PCs system tray. If the Wireless Network Monitor is
enabled, the icon will be green. If the Wireless Network Monitor is
disabled or the Adapter is not connected, the icon will be
gray.
Wireless Network Monitor icon
Link Information ScreensThe opening screen of the Wireless
Network Monitor is Link Information. From this screen, you can see
the strength and quality of your wireless signal. You can also
click More Information to view additional status and statistics
about the wireless connection. To search for available wireless
networks, click Site Survey. To perform configuration changes or
create connection profiles, click Profiles.
Link InformationThe Link Information screen displays network
mode, signal strength, and link quality information about the
current connection. It also provides a button to click for
additional status information.
9
Ad-Hoc Mode or Infrastructure Mode This indicates whether the
Adapter is currently working in Ad-Hoc or Infrastructure mode.
Signal Strength - The Signal Strength bar indicates signal
strength. Link Quality - The Link Quality bar indicates the quality
of the wireless network connection. Click More Information to view
additional information about the wireless network connection on the
Wireless Network Status screen.
Link Information Wireless Network Status
Wireless Network StatusThe Wireless Network Status screen
provides information on your current network settings. Status -
This shows the status of the wireless network connection. SSID -
This is the unique name of the wireless network. Wireless Mode -
The mode of the wireless network currently in use is displayed
here. Transfer Rate - The data transfer rate of the current
connection is shown here. Channel - This is the channel to which
the wireless network devices are set.
10
Security - The status of the wireless security feature is
displayed here. Authentication - This is your wireless networks
authentication method. IP Address - The IP Address of the Adapter
is displayed here. Subnet Mask - The Subnet Mask of the Adapter is
shown here. Default Gateway - The Default Gateway address of the
Adapter is displayed here. DNS - This is the DNS address of the
Adapter. DHCP Client - This displays the Adapters status as a DHCP
client. MAC Address- The MAC address of the wireless networks
access point or wireless router is shown here. Cisco AP IP - This
displays the Cisco AP IP Address when LEAP wireless security is
used. Signal Strength - The Signal Strength bar indicates the
signal strength. Link Quality - The Link Quality bar indicates the
quality of the wireless network connection. Click Back to return to
the initial Link Information screen. Click Statistics to go to the
Wireless Network Statistics screen. Click Save to Profile to save
the currently active connection settings to a profile.
More Information Wireless Network Status
11
Site SurveyThe Site Survey screen displays a list of available
networks in the table on the left. The table shows each networks
SSID, Channel, and the quality of the wireless signal the Adapter
is receiving. You may click SSID, CH (Channel), or Signal, to sort
by that field. SSID - The SSID or unique name of the wireless
network is displayed here. CH - This is the channel that the
network uses. Signal - This is the percentage of signal strength,
from 0 to 100%.
Site Survey
Site InformationFor each network selected, the following
settings are listed: SSID - This the SSID or unique name of the
wireless network. Wireless Mode - This is the mode of the wireless
network currently in use. Channel - This is the channel to which
the wireless network devices are set. Security - The status of the
wireless security feature is displayed here. MAC Address- The MAC
address of the wireless networks access point is displayed
here.
12
Refresh - Click Refresh to perform a new search for wireless
devices. Connect - To connect to one of the networks on the list,
select the wireless network, and click Connect. If the network has
wireless security enabled, a screen requiring security information
will appear. If the network has WEP encryption enabled, then you
will see the WEP
WEP Key Needed
screen. Select the appropriate level of WEP encryption, 64-bit
or 128-bit Then enter the networks Passphrase or WEP Key. To
connect to the network, click Connect. To cancel the connection,
click Cancel. If the network has WPA Personal security enabled,
then you will see the WPA-Personal Needed for Connection screen.
Select the appropriate encryption type, TKIP or AES. Enter the
networks Passphrase or pre-shared key in the Passphrase field. To
connect to the network, click Connect. To cancel the connection,
click Cancel. If the network has PSK2 security enabled, then you
will see the
Key Needed for Connection
WPA-Personal Needed
PSK2 Needed for Connection
screen. Enter the networks Passphrase or pre-shared key in the
Passphrase field. To connect to the network, click Connect. To
cancel the connection, click Cancel.
PSK2 Needed13
ProfilesThe Profiles screen lets you save different
configuration profiles for different network setups. The table on
the left displays a list of available profiles with their profile
names and SSIDs. Profile - The name of the profile is displayed
here. SSID - The SSID or unique name of the wireless network is
displayed here.
Profiles
Site InformationFor each profile selected, the following are
listed: Wireless Mode - This is the mode of the wireless network
currently in use. Channel - This is the channel to which the
wireless network devices are set. Security - The status of the
wireless security feature is displayed here. Authentication - The
authentication setting for the network is shown here.
14
Connect - To connect to a wireless network using a specific
profile, select the profile, and click Connect. New - Click New to
create a new profile. See the next section, Creating a New Profile,
for detailed instructions. Edit - Select the profile you want to
change, and then click Edit. Import - Click Import to import a
profile that has been saved in another location. Select the
appropriate file, and click Open. Export - Select the profile you
want to save in a different location, and click Export. Direct
Windows to the appropriate folder, and click Save.NOTE: If you want
to export more than one profile, you have to export them one at a
time.
Import Profiles
Export ProfilesDelete - Select the profile you want to delete,
and then click Delete.
15
Creating a New ProfileOn the Profiles screen, click New to
create a new profile. Enter a name for the new profile, and click
OK. Click Cancel to return to the Profiles screen without entering
a name. The Available Wireless Network screen provides two options
for setting up a profile. Available Wireless Network. Most users
should use this option. The networks available to this Adapter will
be listed on this screen. You can choose one of these networks and
click the Connect button to connect to it. Click Refresh to update
the Available Wireless Network list. Manual Setup. To set up the
Adapter manually, select Manual Setup.NOTE: Refer to the User Guide
(in English only) for more information on Manual Setup.
Create a New Profile
Available Wireless Network
The setup for each option is described, step by step, under the
appropriate heading on the following pages. Click Exit to close the
Setup Wizard, if you wish to set up the Adapter later.
16
Setting Up the Adapter with an Available NetworkThe available
networks are listed in the table on the center of the screen by
SSID. Select the wireless network you wish to connect to and click
Connect. (If you do not see your network listed, you can click
Refresh to bring the list up again.) If the network utilizes
wireless security, you will need to configure security on the
Adapter. If not, you will be taken directly to the Congratulations
screen.
Available Wireless Network
A
If wireless security has been enabled on this network, you will
see a wireless security screen. If your network uses WEP (Wired
Equivalent Privacy) encryption, the WEP Key Needed for Connection
screen will appear. If your network uses WPA Personal or PSK2
security, a screen will appear for one of those encryption methods.
WEP Key Needed for Connection Select the level of encryption you
want to use, 64-bit or 128bit. Then, enter a passphrase or WEP key.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP
key is automatically generated.
WEP Key Needed17
B
The passphrase is case-sensitive and should not be longer than
31 alphanumeric characters. It must match the passphrase of your
other wireless network devices and is compatible with Linksys
wireless products only. (If you have any non-Linksys wireless
products, enter the WEP key manually on those products.) WEP Key 1
- The WEP key you enter must match the WEP key of your wireless
network. For 64bit encryption, enter exactly 10 hexadecimal
characters. For 128-bit encryption, enter exactly 26 hexadecimal
characters. Valid hexadecimal characters are 0 to 9 and A to F.
Then, click Connect and proceed to the Congratulations screen. To
cancel the connection, click Cancel. WPA-Personal for Connection
WPA Personal offers two encryption methods, TKIP and AES, with
dynamic encryption keys. Select one of these methods. Then enter a
passphrase. Encryption - Select the type of algorithm you want to
use, TKIP or AES, from the Encryption drop-down menu.
WPA-Personal Needed
18
Passphrase - Enter a Passphrase, also called a pre-shared key,
of 8-63 characters in the Passphrase field. The longer and more
complex your Passphrase is, the more secure your network will be.
Then, click Connect and proceed to the Congratulations screen. To
cancel the connection, click Cancel. PSK2 Needed for Connection AES
is automatically used as the encryption method. Enter a passphrase
on this screen. Passphrase - Enter a Passphrase, also called a
pre-shared key, of 8-63 characters in the Passphrase field. The
longer and more complex your Passphrase is, the more secure your
network will be. Then, click Connect and proceed to the
Congratulations screen. To cancel the connection, click Cancel.
PSK2 Needed
For additional information or troubleshooting help, refer to the
User Guide on the Setup CD-ROM. You can also email for further
support.
C
Website http://www.linksys.com/international Product
Registration http://www.linksys.com/registration
After the Adapter has been configured for the network, the
Congratulations screen will appear. Click Connect to Network to
connect to your network. Congratulations! The profile is
complete.
Linksys is a registered trademark or trademark of Cisco Systems,
Inc. and/or its affiliates in the U.S. and certain other countries.
Copyright 2007 Cisco Systems, Inc. All rights
reserved.wmp54gv4.1EULA-qig-70227NC DF
19
Pakkens indhold Trdls-G PCI-netvrkskort n installations-cd-rom n
brugervejledning p cd-rom Installationsvejledning
2,4GHz Trdls-G802.11gWirelessModelnr.
PCI-netvrkskort
Installationsvejledning1
WMP54G (DA)
1
Start installation
VIGTIGT: Installer ikke netvrkskortet p din pc, fr du bliver
bedt om det i trin 2 - ellers installeres netvrkskortet ikke
korrekt.PCI-netvrkskortet installeres og konfigureres ved hjlp af
den guidede konfiguration p den medflgende cd.
A
Placer frst cd-rom'en med guidet konfiguration i cd-rom-drevet.
Den guidede konfiguration kres automatisk, og skrmbilledet Welcome
(Velkommen) vises. Hvis du bliver bedt om at vlge et sprog, skal du
vlge et sprog fra rullemenuen. Klik derefter p Install (Installer).
Klik p knappen Click Here to Start (Klik her for at starte) p
skrmbilledet Welcome (Velkommen) for at installere kortet. Nr du
har lst licensaftalen, skal du klikke p Next (Nste) for at fortstte
installationen. Derefter overfrer Windows filerne til din pc. Den
guidede konfiguration sprger, om du vil installere netvrkskortet p
pc'en. Klik p Next (Nste), hvorefter pc'en slukker. Fortst til trin
2.
B
B
C
C
D
2
2
Tilslutning af kortet
VIGTIGT: For at undg elektrisk std eller skade p pc'en skal du
slukke for strmmen til din pc, og trkke strmkablet ud, inden du
bner kabinettet.
Tilslutning af kortet
A B
Inden du slutter PCInetvrkskortet til pc'en, skal du
kontrollere, at din pc er slukket. bn pc'ens kabinet, og find et
tilgngeligt PCI-stik p bundkortet. Henvend dig til din
computerleverandr for at f yderligere vejledning. Skub PCI-kortet
ind i PCI-stikket. Kontroller, at alle stikbenene berrer
kontaktpunkterne i stikket. Det kan vre ndvendigt at trykke
temmelig hrdt for at skubbe kortet helt ind i stikket. Nr du har
placeret kortet, skal du skrue det fast p pc'ens chassis ved hjlp
af fastgrelsesbjlen. Luk derefter pc'ens kabinet. Tilslut den
eksterne antenne til kortets antennestik. Tnd pc'en. Fortst til
trin 3.
C
Installation af kortet
D E
Placering af antennen3
3
Konfiguration af netvrkskortet
Det nste skrmbillede, der vises, er Available Wireless Network
(Tilgngelige trdlse netvrk). P dette skrmbillede kan du starte en
af de tre konfigurationsmetoder.VIGTIGT: I forbindelse med hurtig
installation skal du kun bruge dette dokument, hvis dit netvrk
vises p skrmbilledet Available Wireless Network (Tilgngelige trdlse
netvrk).
SecureEasySetup: Hvis du bruger SecureEasySetup, skal du klikke
p knappen SecureEasySetup og flge vejledningen p skrmen. Manual
Setup: Hvis du bruger Manual Setup, skal du klikke p knappen Manual
Setup og flge vejledningen p skrmen.
Tilgngelige trdlse netvrk
Konfiguration af netvrkskortet med tilgngelige netvrkP
skrmbilledet Available Wireless Network (Tilgngelige trdlse netvrk)
vises en oversigt over de tilgngelige trdlse netvrk i den midterste
tabel opstillet efter SSID. Vlg det trdlse netvrk, du vil oprette
forbindelse til, og klik p knappen Connect (Opret forbindelse).
(Hvis du ikke fr vist en oversigt over netvrk, kan du klikke p
knappen Refresh (Opdater)). Hvis netvrket bruger trdls sikkerhed,
skal du konfigurere sikkerhed p netvrkskortet. Hvis det ikke gr,
fres du direkte til skrmbilledet Congratulations (Tillykke) - vist
i trin B.
4
A
Hvis du har aktiveret trdls sikkerhed p netvrket, fr du vist et
skrmbillede for trdls sikkerhed. Hvis dit netvrk bruger
WEP-kryptering (Wired Equivalent Privacy), vises skrmbilledet WEP
Key Needed for Connection (WEP-ngle skal bruges til oprettelse af
forbindelse). Hvis dit netvrk bruger WPA-Personal-kryptering (Wi-Fi
Protected Access), vises skrmbilledet WPA-Personal Needed for
Connection (WPA-Personal skal bruges til oprettelse af
forbindelse). Hvis dit netvrk bruger PSK-2-kryptering (Pre-Shared
Key 2 (Foruddelt ngle 2)), vises skrmbilledet PSK2 Key Needed for
Connection (WPA-2-ngle skal bruges til oprettelse af forbindelse).
WEP Key Needed for Connection (WEP-ngle skal bruges til oprettelse
af forbindelse) Vlg 64-bit eller 128-bit. Indtast derefter et
adgangsord eller en WEP-ngle. Passphrase (Adgangsord) - indtast et
adgangsord i feltet Passphrase (Adgangsord). Der skelnes mellem
store og sm bogstaver i adgangsordet, og det br ikke vre lngere end
16 alfanumeriske tegn. Det skal vre identisk med adgangsordet til
dine andre trdlse netvrksenheder og er kun kompatibelt med trdlse
produkter fra Linksys. (Trdlse produkter, der ikke kommer fra
Linksys, krver, at der indtastes en WEP-ngle). WEP Key (WEP-ngle) -
WEP-nglen skal vre identisk med WEP-nglen til dit trdlse netvrk.
Ved 64-bit-kryptering skal du indtaste prcis 10 hexadecimale tegn.
Ved 128 bitkryptering skal du indtaste prcis 26 hexadecimale tegn.
Gyldige hexadecimale tegn er "0" til "9" og "A" til "F". Klik
derefter p Connect (Opret forbindelse), og g videre til trin B.
WEP-ngle skal bruges
5
WPA Personal Needed for Connection (WPA-Personal skal bruges til
oprettelse af forbindelse). Encryption (Kryptering) - Vlg den
algoritme, du vil bruge, TKIP eller AES, i rullemenuen Encryption
(Kryptering). Passphrase (Adgangsord) - Indtast et adgangsord p
8-63 tegn i feltet Passphrase (Adgangsord). Jo lngere og mere
komplekst dit adgangsord er, jo mere sikkert er dit netvrk. Klik p
Connect (Opret forbindelse), og fortst til trin B. PSK2 skal bruges
til oprettelse af forbindelse Indtast et adgangsord p 8-63 tegn i
feltet Passphrase (Adgangsord). Klik p Connect (Opret forbindelse),
og fortst til trin B.
WPA-Personal skal bruges
B
Nr netvrkskortet er konfigureret med netvrket, vises
skrmbilledet Congratulations (Tillykke). Klik p Connect to Network
(Opret forbindelse til netvrk) for at oprette forbindelse til dit
netvrk. Tillykke! Konfigurationen er frdig.
PSK2 skal bruges
BEMRK: Nr netvrkskortet er installeret, bnes skrmbilledet
Wireless Network Monitor (Trdls netvrksovervgning), og dets ikon
vises i proceslinjen p din pc. Dobbeltklik p ikonet, hvis du vil
bne den trdlse netvrksovervgning og finde tilgngelige trdlse netvrk
eller foretage ndringer i konfigurationen.
Ikonet for trdls netvrksovervgning6
Konfiguration af netvrkskortet med SecureEasySetup
(SikkerNemKonfiguration)Med SecureEasySetup
(SikkerNemKonfiguration) er det ikke svrere at installere
netvrkskortet end at trykke p et par knapper. Fr du trykker p nogen
knapper, skal du dog finde knappen SecureEasySetup p den enhed, som
du slutter netvrkskortet til, eksempelvis en trdls router eller et
access point.
Tilgngelige trdlse netvrk
A
Du skal starte i skrmbilledet Available Wireless Network
(Tilgngelige trdlse netvrk), hvor du skal klikke p knappen
SecureEasySetup i hjre side.
B
Du bliver bedt om at finde knappen Secure Easy Setup p den
enhed, som netvrkskortet skal kommunikere med. Hvis du er i tvivl
om, hvor du finder denne knap, kan du klikke p Where can I find the
button? (Hvor kan jeg finde knappen?)
Hvor kan jeg finde knappen?
Herefter fres du igennem et par skrmbilleder, som hjlper dig med
at finde knappen, som normalt er placeret p forsiden af den trdlse
router eller access point'et.
Secure Easy Setup logo og placering7
C
Tryk p Cisco-logoet eller p knappen Secure Easy Setup p den
trdlse router eller access point'et. Nr logoet bliver hvidt og
begynder at blinke, skal du klikke p knappen Next (Nste) i
skrmbilledet Setup Wizard (Guidet konfiguration). Logoet eller
knappen p den trdlse router eller access point'et stopper med at
blinke, nr netvrkskortet er blevet korrekt fjet til netvrket.
Gentag denne fremgangsmde for eventuelle andre
SecureEasySetup-enheder (SikkerNemKonfiguration).
D
Nr SecureEasySetup er fuldfrt, kan du gemme din konfiguration i
en tekstfil ved at klikke p knappen Save (Gem) eller udskrive
konfigurationen ved at klikke p knappen Print (Udskriv). Klik p
Connect to Network (Opret forbindelse til netvrk) for at oprette
forbindelse til dit netvrk. Tillykke! Konfigurationen er frdig.
Tillykke
8
4
Brug af den trdlse netvrksovervgningBEMRK: Du br kun bne den
trdlse netvrksovervgning, EFTER at du har installeret
netvrkskortet.
Du kan bruge den trdlse netvrksovervgning til at kontrollere
linkoplysninger, sge efter tilgngelige trdlse netvrk eller oprette
profiler med forskellige konfigurationer.
Adgang til den trdlse netvrksovervgningNr du konfigureret og
tilsluttet netvrkskortet, vises ikonet for den trdlse
netvrksovervgning p din computers proceslinje. Hvis trdls
netvrksovervgning er aktiveret, er ikonet grnt. Hvis trdls
netvrksovervgning er deaktiveret, eller netvrkskortet ikke er
tilsluttet, er ikonet grt.
Ikonet for trdls netvrksovervgning
LinkoplysningerDet frste skrmbillede, der vises i den trdlse
netvrksovervgning, er Link Information (Linkoplysninger). P dette
skrmbillede kan du se styrken og kvaliteten af det trdlse signal.
Du kan ogs klikke p More Information (Yderligere oplysninger) for
at f vist yderligere status og statistik om den trdlse forbindelse.
Klik p Site Survey (Omrdesgning) for at sge efter tilgngelige
netvrk. Klik p Profiles (Profiler) for at udfre
konfigurationsndringer eller oprette forbindelsesprofiler.
LinkoplysningerSkrmbilledet Link Information (Linkoplysninger)
indeholder oplysninger om netvrkstilstand, signalstyrke og
linkkvalitet for den aktuelle forbindelse. Det indeholder ogs en
knap, som du kan klikke p, hvis du vil have yderligere
statusoplysninger.
9
Ad-Hoc Mode (Ad-hoc-tilstand) eller Infrastructure Mode
(Infrastrukturtilstand) Dette angiver, om netvrkskortet fungerer
korrekt i Ad-Hoc-tilstand eller Infrastrukturtilstand. Signal
Strength (Signalstyrke) Signalstyrkelinjen viser signalstyrken.
Link Quality (Linkkvalitet) - Linkkvalitetslinjen angiver
kvaliteten p den trdlse netvrksforbindelse. Klik p More Information
(Yderligere oplysninger for at f vist flere oplysninger om den
trdlse netvrksforbindelse p skrmbilledet Wireless Network Status
(Status for trdlst netvrk).
Link Information Wireless Network Status (Linkoplysninger Status
for trdlst netvrk)
Status for trdlst netvrkSkrmbilledet Wireless Network Status
(Status for trdlst netvrk) indeholder oplysninger om dine aktuelle
netvrksindstillinger. Status - Viser status for den trdlse
netvrksforbindelse. SSID - Dette er det entydige navn p det trdlse
netvrk. Wireless Mode (Trdls tilstand) Tilstanden for det trdlse
netvrk, der aktuelt er i brug, vises her. Transfer Rate
(Overfrselshastighed) Dataoverfrselshastigheden for den aktuelle
forbindelse vises her. Channel (Kanal) - Dette er den kanal, som
det trdlse netvrk er indstillet til.
10
Security (Sikkerhed) - Status for den trdlse sikkerhedsfunktion
vises her. Authentication (Godkendelse) - Dette er det trdlse
netvrks godkendelsesmetode. IP Address (IP-adresse) - IP-adressen
for netvrkskortet vises her. Subnet Mask (Undernetmaske)
Undernetmasken for netvrkskortet vises her. Default Gateway
(Standardgateway) Standardgateway-adressen p netvrkskortet vises
her. DNS - Dette er netvrkskortets DNS-adresse. DHCP Client
(DHCP-klient) - Viser netvrkskortets status som en DHCP-klient MAC
Address (MAC-adresse) - MACadressen p det trdlse netvrks access
point eller trdlse router vises her. Cisco AP IP - Viser Cisco AP
IP-adressen, nr der anvendes LEAP trdls sikkerhed. Signal Strength
(Signalstyrke) Signalstyrkelinjen angiver signalstyrken. Link
Quality (Linkkvalitet) - Linkkvalitetslinjen angiver kvaliteten p
den trdlse netvrksforbindelse. Klik p Back (Tilbage) for at vende
tilbage til skrmbilledet Link Information (Linkoplysninger). Klik p
Statistics (Statistik) for g til skrmbilledet Wireless Network
Statistics (Statistik for trdlst netvrk). Klik p Save to Profile
(Gem i profil) for at gemme de aktuelt aktive
forbindelsesindstillinger i en profil.
More Information Wireless Network Status (Flere oplysninger
Status for trdlst netvrk)
11
Site Survey (Omrdesgning)Skrmbilledet Site Survey (Omrdesgning)
viser en oversigt over tilgngelige netvrk i tabellen til venstre.
Tabellen viser hvert netvrks SSID, kanal og kvaliteten af det
trdlse signal, som netvrkskortet modtager. Du kan klikke p SSID, CH
(Channel (Kanal)) eller Signal for sortere efter dette felt. SSID -
SSID'et eller det entydige navn p det trdlse netvrk vises her. CH
(Kanal) - Dette er den kanal, som netvrket bruger. Signal - Dette
er procentangivelsen af signalstyrken, fra 0 til 100 %.
Site Survey (Omrdesgning)
Site Information (Omrdeoplysninger)For hvert valgt netvrk
angives flgende indstillinger: SSID - Dette er SSID'et eller det
entydige navn p det trdlse netvrk. Wireless Mode (Trdls tilstand) -
Dette er tilstanden for det trdlse netvrk, der aktuelt er i brug.
Channel (Kanal) - Dette er den kanal, som det trdlse netvrk er
indstillet til. Security (Sikkerhed) - Status for den trdlse
sikkerhedsfunktion vises her. MAC Address (MAC-adresse) -
MACadressen p det trdlse netvrks access point vises her.
12
Refresh (Opdater) - Klik p Refresh (Opdater) for at udfre en ny
sgning eller trdlse enheder. Connect (Opret forbindelse) - Vlg et
trdlst netvrk, og klik p Connect (Opret forbindelse) for at oprette
forbindelse til et af netvrkene i oversigten. Hvis den trdlse
sikkerhed for netvrket er aktiveret, vises der et skrmbillede, hvor
du skal angive sikkerhedsoplysninger. Hvis WEP-krypteringen for
netvrket er aktiveret, vises skrmbilledet WEP Key Needed for
Connection (WEP-ngle skal bruges til oprettelse af forbindelse).
Vlg det relevante niveau for WEP-kryptering, dvs. 64 bit eller 128
bit. Derefter skal du angive netvrkets adgangsord eller WEP-ngle.
Klik p Connect (Opret forbindelse) for at oprette forbindelse til
netvrket. Klik p Cancel (Annuller) for at annullere tilslutningen.
Hvis WPA Personal-sikkerhed er aktiveret for netvrket, vises
skrmbilledet WPA-Personal Needed for Connection (WPA-Personal skal
bruges til oprettelse af forbindelse). Vlg den relevante
krypteringstype, dvs. TKIP eller AES. Indtast netvrkets adgangsord
eller Pre-Shared Key i feltet Passphrase (Adgangsord). Klik p
Connect (Opret forbindelse) for at oprette forbindelse til
netvrket. Klik p Cancel (Annuller) for at annullere tilslutningen.
Hvis PSK2-sikkerhed er aktiveret for netvrket, vises skrmbilledet
PSK2 Needed for Connection (PSK2 skal bruges til oprettelse af
forbindelse). Indtast netvrkets adgangsord eller Pre-Shared Key i
feltet Passphrase (Adgangsord). Klik p Connect (Opret forbindelse)
for at oprette forbindelse til netvrket. Klik p Cancel (Annuller)
for at annullere tilslutningen.
WEP-ngle skal bruges
WPA-Personal skal bruges
PSK2 skal bruges13
ProfilerI skrmbilledet Profiles (Profiler) kan du gemme
forskellige konfigurationsprofiler for forskellige
netvrksopstninger. Tabellen til venstre indeholder de tilgngelige
profiler samt deres profilnavne og SSID'er. Profile (Profil) -
Navnet p profilen vises her. SSID - SSID'et eller det entydige navn
p det trdlse netvrk vises her.
Profiles (Profiler)
Site Information (Omrdeoplysninger)For hver valgt profil angives
flgende: Wireless Mode (Trdls tilstand) - Dette er tilstanden for
det trdlse netvrk, der aktuelt er i brug. Channel (Kanal) - Dette
er den kanal, som det trdlse netvrk er indstillet til. Security
(Sikkerhed) - Status for den trdlse sikkerhedsfunktion vises her.
Authentication (Godkendelse) Godkendelsesindstillingen for netvrket
vises her.
14
Connect (Opret forbindelse) - Hvis du vil oprette forbindelse
til et trdlst netvrk vha. en bestemt profil, skal du vlge profilen
og klikke p Connect (Opret forbindelse). New (Ny) - Klik p New (Ny)
for at oprette en ny profil. En detaljeret vejledning finder du i
det nste afsnit, Oprettelse af en ny profil. Edit (Rediger) - Vlg
den profil, du vil ndre, og klik p Edit (Rediger) Import (Importer)
- Klik p Import (Importer) for at importere en profil, der er
blevet gemt p en anden placering. Vlg den relevante profil, og klik
p bn. Export (Eksporter) - Vlg den profil, du vil gemme p en anden
placering, og klik p Export (Eksporter). Angiv stien til den
relevante mappe, og klik p Gem. BEMRK: Hvis du vil eksportere mere
end n profil, skal du eksportere dem en ad gangen. Delete (Slet) -
Vlg den profil, du vil slette, og klik p Delete (Slet).
Importer profiler
Eksporter profiler
15
Oprettelse af en ny profilKlik p New (Ny) p skrmbilledet
Profiles (Profiler) for at oprette en ny profil. Angiv et navn p
den nye profil, og klik p OK. Klik p Cancel (Annuller) for at vende
tilbage til skrmbilledet Profiles (Profiler) uden at angive et
navn. Skrmbilledet Available Wireless Network (Tilgngelige trdlse
netvrk) indeholder to muligheder for at konfigurere en profil.
Available Wireless Network (Tilgngelige trdlse netvrk). De fleste
brugere br bruge denne indstilling. Dette skrmbillede indeholder en
oversigt over tilgngelige netvrk for dette netvrkskort. Du kan vlge
et af disse netvrk og klikke p knappen Connect (Opret forbindelse)
for at oprette forbindelse til det. Klik p Refresh (Opdater) for at
opdatere oversigten Available Wireless Network (Tilgngelige trdlse
netvrk). Manual Setup (Manuel konfiguration). Hvis du vil
konfigurere netvrkskortet manuelt, skal du vlge Manual Setup
(Manuel konfiguration). BEMRK: Ls brugervejledningen (kun p
engelsk) for at f yderligere oplysninger om manuel konfiguration.
Konfigurationen for hver indstilling er beskrevet trin for trin
under den relevante overskrift p de flgende sider. Klik p Exit
(Afslut) for at lukke den guidede konfiguration, hvis du vil
konfigurere netvrkskortet p et senere tidspunkt.
Opret en ny profil
Tilgngelige trdlse netvrk
16
Konfiguration af netvrkskortet med et tilgngeligt netvrkDe
tilgngelige netvrk vises i tabellen midt p skrmbilledet opstillet
efter SSID. Vlg det trdlse netvrk, du vil oprette forbindelse til,
og klik p Connect (Opret forbindelse). (hvis du ikke kan se dit
netvrk p oversigten, kan du klikke p Refresh (Opdater) for at f
vist oversigten igen). Hvis netvrket anvender trdls sikkerhed, skal
du konfigurere sikkerheden p netvrkskortet. Hvis ikke, bnes
skrmbilledet Congratulations (Tillykke).
Tilgngelige trdlse netvrk
A
Hvis du har aktiveret trdls sikkerhed p netvrket, fr du vist et
skrmbillede for trdls sikkerhed. Hvis dit netvrk bruger
WEP-kryptering (Wired Equivalent Privacy), vises skrmbilledet WEP
Key Needed for Connection (WEP-ngle skal bruges til oprettelse af
forbindelse). Hvis dit netvrk bruger WPA Personal- eller
PSK2-sikkerhed, vises der et skrmbillede for en af disse
krypteringsmetoder. WEP Key Needed for Connection (WEP-ngle skal
bruges til oprettelse af forbindelse) Vlg det sikkerhedsniveau, du
vil bruge: 64-bit eller 128-bit. Indtast derefter et adgangsord
eller en WEP-ngle. Passphrase (Adgangsord) - Indtast et adgangsord
i feltet Passphrase (Adgangsord), s der automatisk oprettes en
WEP-ngle.
WEP-ngle skal bruges
17
B
Der skelnes mellem store og sm bogstaver i adgangsordet, og det
br ikke vre lngere end 31 alfanumeriske tegn. Det skal vre identisk
med adgangsordet til dine andre trdlse netvrksenheder og er kun
kompatibelt med trdlse produkter fra Linksys. (Hvis du har
installeret trdlse produkter, der ikke kommer fra Linksys, skal du
indtaste WEP-nglen manuelt p disse produkter.) WEP Key 1 (WEP-ngle
1) - Den WEP-ngle, du indtaster, skal vre identisk med WEP-nglen
til dit trdlse netvrk. Ved 64-bit-kryptering skal du indtaste prcis
10 hexadecimale tegn. Ved 128 bit-kryptering skal du indtaste prcis
26 hexadecimale tegn. Gyldige hexadecimale tegn er "0" til "9" og
"A" til "F". Klik derefter p Connect (Opret forbindelse), og fortst
til skrmen Congratulations (Tillykke). For at afbryde forbindelsen
skal du klikke p Cancel (Annuller). WPA-Personal for Connection
(WPA-Personal til oprettelse af forbindelse) WPA Personal har to
krypteringsmetoder, TKIP og AES, med dynamiske krypteringsngler.
Vlg en af disse metoder. Indtast dernst et adgangsord. Encryption
(Kryptering) - Vlg den algoritmetype, du nsker at anvende, TKIP
eller AES, fra rullemenuen Encryption.
WPA-Personal skal bruges
18
Passphrase (Adgangsord) - Indtast et adgangsord, ogs kaldet
PreShared Key (Foruddelt ngle), p 863 tegn i feltet Passphrase
(Adgangsord). Jo lngere og mere komplekst dit adgangsord er, jo
mere sikkert er dit netvrk. Klik derefter p Connect (Opret
forbindelse), og fortst til skrmbilledet Congratulations
(Tillykke). Klik p Cancel (Annuller) for at annullere forbindelsen.
PSK2 Needed for Connection (PSK2 skal bruges til oprettelse af
forbindelse) AES bruges automatisk som krypteringsmetode. Indtast
et adgangsord p dette skrmbillede. Passphrase (Adgangsord) -