contents Specifications Outline Dimensions 30100C Fully Extended Boom/Jib Range Diagram 30100C Fully Extended Boom/Jib Load Charts 30100C Intermediate Boom/Jib Range Diagram 30100C Intermediate Boom/Jib Load Charts 30124C Fully Extended Boom/Jib Range Diagram 30124C Fully Extended Boom/Jib Load Charts 30124C Intermediate Boom/Jib Range Diagram 30100C Intermediate Boom/Jib Load Charts Load Chart Data CraneCARE SM 2 4 6 7 8 9 10 11 12 13 14 15 data models 30100C 30124C product guide features • 30 ton (27,3 mton) capacity • 5-section 124' (37,8 m) proportional boom • 4-section 100' (30,5 m) proportional boom • 134' 8" (41 m) maximum main boom tip height • 2-section, 30' 6" (9,3 m) to 55' (16,8 m) jib • 165' 11" (50,6 m) maximum tip height • 2-speed planetary hoist with 14,500 lb (6 591 kg) theoretical line pull on bottom layer • Removable boom rest • Load moment indicator—with digital display and overload shutdown • 22' 1.25" (6,7 m) out-and-down outriggers at full extension • Intermediate and fully extended outrigger charts are standard • System pressure gauge • Clamp-on mounting • Rugged, weatherproof, automotive style electrical system • Manitowoc CraneCARE SM comprehensive support
15
Embed
Manitowoc Boom Truck 215245-30100 30124 - Bigge · 10. Lifting off the main boom point while the swing-around jib is erected is not intended or approved. 11. All load ratings above
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
contentsSpecifications
Outline Dimensions
30100C Fully ExtendedBoom/Jib Range Diagram
30100C Fully ExtendedBoom/Jib Load Charts
30100C IntermediateBoom/Jib Range Diagram
30100C IntermediateBoom/Jib Load Charts
30124C Fully ExtendedBoom/Jib Range Diagram
30124C Fully ExtendedBoom/Jib Load Charts
30124C IntermediateBoom/Jib Range Diagram
30100C IntermediateBoom/Jib Load Charts
Load Chart Data
CraneCARESM
24
6
7
8
9
10
11
12
1314
15
da
tamodels 30100C
30124Cproductguide
features
• 30 ton (27,3 mton) capacity
• 5-section 124' (37,8 m) proportional boom
• 4-section 100' (30,5 m) proportional boom
• 134' 8" (41 m) maximum main boom tip height
• 2-section, 30' 6" (9,3 m) to 55' (16,8 m) jib
• 165' 11" (50,6 m) maximum tip height
• 2-speed planetary hoist with 14,500 lb (6 591 kg)theoretical line pull on bottom layer
• Removable boom rest
• Load moment indicator—with digital display and overload shutdown
• 22' 1.25" (6,7 m) out-and-down outriggers at full extension
• Intermediate and fully extended outriggercharts are standard
• System pressure gauge
• Clamp-on mounting
• Rugged, weatherproof, automotive style electrical system
• Manitowoc CraneCARESM
comprehensive support
Underframe Out-and-Down Type Stabilizers –8' (2,4 m) retracted; 18' 6" (5,6 m) extended. Operatedindependently for precise leveling. Double-acting hydrauliccylinders. Fixed pad size is 12" (305mm) diameter.
Subframe – Torsionally resistant, rigid 4-plate design.Mounted under crane full length of truck frame.
Rear Underride Protection – Supplied on factory-mountedcranes. Fabricated structure mounted under rear of bed.Complies with Bureau Motor Carrier Safety Standard 393.86.
Dual operator platforms are equipped with four single-levercrane controls arranged to ANSI B30.5 standards. Fullyproportional control valves and system pressure gauge. Eachstation also includes outrigger and stabilizer controls,engine start/stop, foot throttle, signal horn, boom-angleindicator, bubble levels, load chart and range diagram.
Hydraulics
Hydraulic System – A 3-section vane pump direct-mounted to power take-off on truck transmission provides42 gpm (159 lpm) to the hoist, 28 gpm (106 lpm) to theboom hoist and telescope circuit, and 12 gpm (45 lpm) tothe swing and outrigger circuit. 100-gallon (379-liter)baffled reservoir includes suction ball valve with strainertwo 25-micron filters in the return line. Use of SAE O-ringand face seal O-ring hydraulic fittings throughout system.
Hydraulic Cylinders – All load-holding cylinders areequipped with integral holding valves.
Warning Systems
Load Moment Indicator – Senses boom hoist cylinderpressure, boom length and boom angle. Audio-visualwarning indicated overload conditions and overloadshutoff feature prevents continuing overload. Operatorcan access all relative crane configuration and loadconditions via display at the operator station.
Anti-Two-Block System – Audible warning and shutofffunctions prevent hook from contacting boom point.
Back-Up Alarm – Supplied on factory-mounted cranes,electronic audible motion alarm activated when trucktransmission is in reverse gear.
General
Electrical – State-of-the-art, weather-resistant componentsthroughout. Automotive style electrical system for easy
Upperworks
Boom
Booms – Inverted T-cross section, 4-or 5-sectiontelescoping type, extended and retracted proportionally bya double-acting hydraulic cylinder and cable-crowd system.30100C – 4-Section 30' 6" (9,3 m) to 100' 0" (30,5 m).Maximum main boom tip height 111' 4" (33,9 m). 2-section, 31' (9,5 m) to 55' (16,8 m) jib. Maximum tipheight 166' 8" (50,8 m). 30124C – 5-section 31' 5/8" (9,5 m)to 123' 8 5/8" (37,7 m). Maximum main boom tip height134' 8"(41,1 m). 1-section, 31' (9,5 m) jib. Maximum tipheight 165' 11" (50,6 m).
Quick Reeve Boom Point – Three high-density nylonsheaves mounted on heavy-duty roller bearings. Tworemovable pin-type rope guards.
Boom Elevation – Double-acting hydraulic cylinder.Working range from 10˚ below horizontal to 80˚ above.
Load Hook – 5-ton (4,5 mton) capacity hook with heavy-duty swivel and weight is provided for single-line operation.
Hoist
Hoist – Maximum theoretical line speed 380 fpm (115,8 mpm). Maximum theoretical bottom-layer line pull 14,500 lb (6 577 kg). Two-speedplanetary reducer. Wet multi-disc internal brake isspring-applied, pressure-released.
Wire Rope – 335' (102,1 m) of 5/8" (16 mm) rotationresistant type.
Swing System
Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum theoretical swing speed1.5 rpm. Wet multi-disk internal brake is spring-applied, pressure-released. Oversized diameter ball-bearing swing circle with external gear. 372˚ non-continuous rotation.
Outriggers
Out-and-down style outriggers, operated independentlyfor precise leveling. 22' 1 1/4" (6,8 m) spread at fullextension and 13' 4" (4,1 m) spread at intermediateextension. 16" (406 mm) diameter floats. Bubble levellocated near outrigger controls.
Mounting
Mounting – Pedestal and subframe are mounted tochassis by threaded rods and clamp plates. No welding,drilling, or bolting to truck frame is required.
2
specifications
mo
de
ls3
010
0C
, 3
012
4C
10. Lifting off the main boom point while the swing-around jib is erected is not intended or approved.
11. All load ratings above the heavy line are based onmachine structural competence and do not exceed 85%of tipping. Load ratings below are stability limited anddo not exceed 85% of tipping.
12. Do not operate a Manitowoc truck-mounted craneor accessories within 10' (3,05 m) of live power lines.
13. This capacity chart is for reference only and mustnot be used for specific serial number cranes.
Information
1. Deductions must be made from rated loads for stowedjib, optional attachments, hooks, and loadblocks (seededuction chart). Weights of slings and all other load-handling devices shall be considered a part of the load.
2. Load ratings above the heavy line are structurally limitedcapacities. Load ratings below the heavy line are stabilitylimited capacities and do not exceed 85% of tipping.
Definitions
1. Operating radius (r ) is the horizontal distance fromthe axis of rotation to the center of the vertical hoist lineor tackle with load applied (see below).
2. Loaded boom angle (�), as shown in the columnheaded by �, is the included angle between thehorizontal and longitudinal axis of the boom base afterlifting rated load at rated radius (see below).
installation. Designed to withstand high pressurewashing and varying climates.
Design/Welding – Design conforms to ANSI B30.5.Welding conforms to AWS D1.1. Tested to SAE 1063and SAE 765.
Manuals – Operator, service and parts manuals depictcorrect crane operation, maintenance procedures andparts listing.
Warranty – 12-month warranty covers parts and laborresulting from defects in material and workmanship.
Warning
1. The operator must read and understand the owner’smanual before operating this crane.
2. Positioning or operation of crane beyond areas shownon this chart is not intended or approved except wherespecified in owner’s manual.
3. Loaded boom angles at specified boom lengths giveonly an approximation of the operating radius. Theboom angle before loading should be greater toaccount for deflections. Do not exceed the operatingradius for rated loads.
4. The operating radius shown in the jib rating chart isfor fully extended boom only. When boom is not fullyextended, use only loaded boom angle to determine loadrating of jib.
5. For boom angles shown on jib load rating chart, userating of next lower boom angle.
6. For boom lengths not shown, use rating of nextshorter or longer boom length, whichever is less. Forradii not shown, use rating of next longer radius.
7. Crane load ratings on outriggers are based on freelysuspended loads with the machine leveled and standing on afirm, uniform supporting surface. No attempt shall be madeto move a load horizontally on the ground in any direction.
8. Practical working loads depend on supporting surface,wind, and other factors affecting stability such ashazardous surroundings, experience of personnel, andproper handling, all of which must be taken intoaccount by the operator.
9. The maximum load which may be telescoped islimited by hydraulic pressure, boom angle, and boomlubrication. It is safe to attempt to telescope any loadwithin the limits of the load rating chart.
3
specifications
mo
de
ls3
010
0C
, 3
012
4C
NOTE: Due to continuing improvements, Manitowoc Boom Trucks reserves the right to change product specifications without notice.
�
r
4
outline dimensions
mo
de
ls3
010
0C
, 3
012
4C
22' 4"(6,81 m)
4' 10.25"(1,48 m)
13.4"(340 mm)32"
(813 mm)
32.6"(828 mm)
192" CT (4 877 mm)
258" WB (6 553 mm)
40" OAL (12,19 m)
69.1" (1 755 mm)
114" AF (2 896 mm)
40"(1 016 mm)
45.2"(1 148 mm)
52.5"(1 334 mm)
11.3"(287 mm)
27.3"(693 mm)
Wheelbase (WB)
Cab to Tandem (CT)
After Frame (AF)
Frame Section Modulusat 180 ˚ Area of Operation
Frame Section Modulusat 360 ˚ Area of Operation*
Front Axle Gross Weight Rating
Rear Axle Gross Weight Rating
Minimum Truck Axle Weight – Front**
Minimum Truck Axle Weight – Back**
Nominal Frame Width
258"(6 553 mm)
192"(4 877 mm)
114"(2 896 mm)
25.0 in3
110,000 psi(758 450 kPa)
33.0 in3
110,000 psi(758 450 kPa)
18,000 lb(8 165 kg)
40,000 lb(18 144 kg)
8,100 lb(3 674 kg)
8,300 lb(3 765 kg)
34 "(864 mm)
258"(6 553 mm)
192"(4 877 mm)
114"(2 896 mm)
25.0 in3
110,000 psi(758 450 kPa)
33.0 in3
110,000 psi(758 450 kPa)
18,000 lb(8 165 kg)
40,000 lb(18 144 kg)
9,200 lb(4 173 kg)
8,300 lb(3 765 kg)
34 "(864 mm)
Chassis Data
Minimum Truck Requirements 30100C 30124C
Total Crane - Out-and-Down Outriggers
22'(6,71 m) Flat Bed
30' 6” (9,30 m) Fixed Length Jib
31' (9,45 m) Fixed Length Jib
30' 6”-55' (9,30 m-16,80 m) Telescopic Jib
27,166 lb(12 323 kg)
2,000 lb(907 kg)
1,126 lb(511 kg)
—
1,754 lb(796 kg)
28,586 lb(12 967 kg)
2,000 lb(907 kg)
—
850 lb(386 kg)
—
Weights
*Frame section modules at 360˚ area of operationrequires front bumper stabilizer.**Minimum chassis weight is required to meet85% stability requirements.
Chassis data is general – not for engineering.Some dimensions depend on truck selection.
OAH Overall HeightCT Cab to TandemCA Cab to AxleWB Wheel BaseOAL Overall LengthBBC Bumper to Back of CabAF Afterframe
26.5"(673 mm)
12' 9" OAH(3,89 m)
30100C 30124C
30' 6"(9,30 m)
RETRACTED
100' 0"(30,48 m)EXTENDED
30100C31' 1"
(9,47 m)RETRACTED
124' 0"(37,80 m)EXTENDED
30124C
outline dimensions
mo
de
ls3
010
0C
, 3
012
4C
80 ˚
10 ˚
5
22' 1.25"(6,74 m)
8"(203 mm)
9.6"(244 mm)
18' 6" (5,64 m)
A
Configuration
Extended Boom
Fixed or Retracted Jib
Extended Jib
Maximum Tip Height (A)
Boom100' (30,5 m)
111' 4"(33,9 m)
142' 1"(43,3 m)
166' 8"(50,8 m)
Boom124' (37,8 m)
134' 8" (41,1 m)
165' 11"(50,6 m)
—
30100C 30124C
10" (254 mm)6"
(152 mm)
boom/jib range diagram
6
mo
de
l3
010
0C
30100C Range Diagram - Fully Extended
222.0 REF - 18' 6"(5,64 m)
264.0 REF - 22' 0"(6,71 m)
(A) (B)(C)
FIRST SECTION
SECOND SECTION
STABILIZERS
GROUND
OUTRIGGERS
(A) Pins must be disengaged for thisoutrigger configuration
(B) These marks indicate when beams are fully extended
(C) All outrigger beams must be extended to full extend mark
NOTE: Use this chart only when outriggersand stabilizers are fully extended.
7
boom/jib load charts
mo
de
l3
010
0C
Operating Radius
ft (m)
6 (1,8)
8(2,4)
10(3,1)
12(3,7)
15(4,6)
20(6,1)
25(7,6)
30(9,1)
35(10,7)
40(12,2)
45(13,7)
50(15,2)
55(16,8)
60(18,3)
65(19,8)
70(21,3)
75(22,9)
80(24,4)
85(25,9)
90(27,4)
95(29,0)
100(30,5)
Deduction*
Deduction**
30100C Load Ratings - Fully Extended Outrigger SpreadA B C D
lb(kg)
lb(kg)
lb(kg)
lb(kg)
lb(kg)
Boomft (m)
Operating Radius
ft (m)
6(1,8)
8(2,4)
10(3,1)
12(3,7)
15(4,6)
20(6,1)
25(7,6)
30(9,1)
35(10,7)
40(12,2)
45(13,7)
50(15,2)
55(16,8)
60(18,3)
65(19,8)
70(21,3)
75(22,9)
80(24,4)
85(25,9)
90(27,4)
95(29,0)
100(30,5)
Boomft (m)
31 52 68 84 100(9,5) (15,9) (20,7) (25,6) (30,5)
*for stowed fixed jib
**for stowed telescopic jib
� � � � �
Meets ANSI B30.5 Requirements - Do not operate crane or accessories within 10' (3.05m) of live power lines.NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
(B) Pins must be engaged for this outrigger and stabilizer configuration
(C) Both outrigger and stabilizer beams must be extended tomid extend mark
NOTE: Lifting personnel with crane in thisoutrigger configuration is strictly prohibited.Use only fully extended outrigger configurationwhen lifting personnel.
Use this chart only when front outriggers andrear stabilizers are in the intermediate position.
9
Meets ANSI B30.5 Requirements - Do not operate crane or accessories within 10' (3.05m) of live power lines.NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
boom/jib load charts
mo
de
l3
010
0C
Operating Radius
ft (m)
6(1,8)
8(2,4)
10(3,0)
12(3,7)
15(4,3)
20(5,2)
25(6,1)
30(7,6)
35(9,1)
40(10,7)
45(12,2)
50(13,7)
55(15,2)
Deduction*
Deduction**
30100C Load Ratings - Intermediate Outrigger Spread A B C D
(A) Pins must be disengaged for thisoutrigger configuration
(B) These marks indicate when beams are fully extended
(C) All outrigger beams must be extended to full extend mark
NOTE: Use this chart only when outriggersand stabilizers are fully extended.
11
mo
de
l3
012
4C
Meets ANSI B30.5 Requirements - Do not operate crane or accessories within 10' (3.05m) of live power lines.NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
boom/jib load charts
Operating Radius
ft (m)
6(1,8)
8(2,4)
10(3,0)
12(3,7)
15(4,6)
20(6,1)
25(7,6)
30(9,1)
35(10,7)
40(12,2)
45(13,7)
50(15,2)
55(16,8)
60(18,3)
65(19,8)
70(21,3)
75(22,9)
80(24,4)
85(25,9)
90(27,4)
95(29,0)
Deduction*
30124C Load Ratings - Fully Extended Outrigger SpreadA B C D
(B) Pins must be engaged for this outrigger and stabilizer configuration
(C) Both outrigger and stabilizer beams must be extended to mid extend mark
NOTE: Lifting personnel with crane in thisoutrigger configuration is strictly prohibited.Use only fully extended outrigger configurationwhen lifting personnel.
Use this chart only when front outriggers andrear stabilizers are in the intermediate position.
Operating Radius
ft (m)
6(1,8)
8(2,4)
10(3,1)
12(3,7)
15(4,6)
20(6,1)
25(7,6)
30(9,1)
35(10,7)
40(12,2)
45(13,7)
50(15,2)
13
boom/jib load charts
mo
de
l3
012
4C
Meets ANSI B30.5 Requirements - Do not operate crane or accessories within 10' (3.05m) of live power lines.NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
Anti-two-block system must be in good operatingcondition before operating crane. Refer to theowner’s manual. Keep at least three wraps of loadline on the drum at all times.
1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line
9,080 lb 18,160 lb 27,240 lb 36,320 lb 45,000 54,480(4 119 kg) (8 237 kg) (12 356 kg) (16 474 kg) (20 593 kg) (24 712 kg)
10,000 lb 20,000 lb 30,000 lb 40,000 lb 50,000 lb 60,000 lb(4 536 kg) (9 072 kg) (13 608 kg) (18 144 kg) (22 680) (27 216 kg)
Allowable Line Pull 30100C
Line through thecenterline of rotation
14
mo
de
ls3
010
0C
, 3
012
4C
180˚ Full CapacityWork Area
1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line 7 Part Line
9,080 lb 18,160 lb 27,240 lb 36,320 lb 45,400 54,480 60,000(4 119 kg) (8 237 kg) (12 356 kg) (16 474 kg) (20 593 kg) (24 712 kg) (27 216 kg)
9,500 lb 19,000 lb 28,500 lb 38,000 lb 47,500 lb 57,000 lb 60,000(4 309 kg) (8 618 kg) (12 927 kg) (17 237 kg) (21 546) (25 855 kg) (27 216 kg)
Allowable Line Pull 30124C
CraneCARE is Manitowoc Boom Trucks’ complete serviceand support program. Incorporated into this program areservice training, immediate parts availability, professionalfield service, and technical support and documentation.CraneCARE is available for every one of the thousands ofcranes still operating all over the world.
That’s dedication and devotion that you won’t getanywhere else.
That’s CraneCARE.
Service Training
A certified Manitowoc Boom Trucks service specialist workswith you in your training facility or in the field to ensurethat you know how to achieve maximum performance,dependability, and years from your cranes.
A reputable Manitowoc Boom Trucks Service techniciancomes to you to provide valuable training to all distributorson the crane’s LMI system.
Parts Availability
Genuine Manitowoc Boom Trucks replacement parts may be obtained through your MBT distributor on aregular basis.
Hydraulic Test Kit with Case – Part No. 499792-9• Small national O-ring kit• Pressure gauges• Fluke multi-meter• Hydraulic flow meters• Multi-load grease gun• 6-drawer tool box• 17-piece wrench set
Field Service
Factory-trained service experts are always ready to helpmaintain your crane’s peak performance.
For a worldwide listing of dealer locations, please consultour website at: www.manitowocbt.com.
Technical Support
Manitowoc Boom Trucks’ dealer network and factorypersonnel are available 24 hours a day, 7 days a week, 365days a year to answer your technical questions and more.
For a worldwide listing of dealer locations, please consultour website at: www.manitowocbt.com.
Technical Documentation
Manitowoc Boom Trucks boast an extensive, easy-to-understand library of documentation.
A complete set of Operator’s parts and service manuals areincluded with each crane.
Additional copies are available through your AuthorizedManitowoc Boom Trucks Distributor.