Managing Welding Induced Distortion – Comparison of different computational approaches Mehdi Ghanadi 1) and Zuheir Barsoum 2) 2) Department of Aeronautical & Vehicle Engineering KTH Royal Institute of Technology, Stockholm, Sweden [email protected]3 rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016 1) Department of Virtual Product Development Structure and Durability Volvo Construction Equipment, Braås, Sweden
19
Embed
Managing Welding Induced Distortion – …...Managing Welding Induced Distortion – Comparison of different computational approaches Mehdi Ghanadi1) and Zuheir Barsoum2) 2) Department
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Managing Welding Induced Distortion – Compar ison of d i f ferent computat ional approaches
Mehdi Ghanadi1) and Zuheir Barsoum2)
2) Department of Aeronautical & Vehicle Engineering KTH Royal Institute of Technology, Stockholm, Sweden [email protected]
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
1) Department of Virtual Product Development Structure and Durability Volvo Construction Equipment, Braås, Sweden
Background
• Accurate and reliable distortion predictions are essential for structural integrity of welded structures
If Inherent Strain is known; welding distortion can be computed by elastic analysis
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Specimens and experimental set up
8
- T-fillet joint with S355 steel • D u r i n g w e l d i n g , t h e
baseplate has been clamped in one side and in 60 mm f r o m c e n t e r o f t h e baseplate.
- Welding deformation
measurements • device is moved on the
surface of the specimen and measures the deformation of some specified points both on baseplate and stiffener
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Nonlinear FEA for welding simulation
9
- weld bead is divided into adequate number of volumes (blocks) which will be used in the implementation of the moving heat source and rapid dumping approach.
- Non-linear, temperature dependent material properties were used
500mm
500mm
Stress extraction points
Welding direction
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Inherent strain zone
10
- Determined through the non-linear FEA • Residual plastic strain created
due plastic deformation during welding
- Good approximation; Average value of the inherent strain distribution along the weld line
- Elastic FEA may be used to predict the welding distortion when the inherent strain region and averaged magnitude is known for the particular joint.
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Elastic FEA
11
Inherent strain approach - Magnitude of inherent strain ε, consists of bending (εb) and membrane (εm)
- The inherent strain components are integrated over thickness (t) and the results applies on each element in the inherent strain zone,
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Elastic FEA
12
Inherent deformation approach - integration of inherent strain over the cross section of the plate and perpendicular to welding line - The inherent deformation may be divided into four components
• Longitudinal shrinkage (δ*L)
• Transverse shrinkage (δ*T)
• Longitudinal bending (θ*L)
• Transverse bending (θ*T)
The average value of inherent deformation components along welding length (Lw)
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Elastic FEA
13
Inherent deformation approach - Inheren t de fo rmat i on and
inherent bending in web-flange
- Average values as straight lines
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Elastic FEA
14
Shrinkage force approach - Welding distortion can also be
calculated by applying equivalent force and moments
- Applied on inherent strain zone: • longitudinal shrinkage force (Fz) • longitudinal moment (Mz) • transverse shrinkage force (Fx) • transverse moment (Mx)
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Comparsion of different approaches
15
- Transverse bending - Longitudinal bending
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Comparsion of different approaches
16
- Longitudinal, transverse shrinkages and angular distortion
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Conclusions
17
- The determination of the inherent strain distribution is essential in order to carry out the elastic FEA
- Large variation is observed in the start and stop position of the welding, i.e. edge effects. Average value of the inherent deformation should be calculated by neglecting the results from the nodes and elements locate near the plate edges.
- It is observed that the inherent strain predicts the distortion with good accuracy as compared with the other approaches. The inherent deformation and shrinkage force requires an integration step, which will result in a poorer distortion approximation.
- Inherent strain and inherent deformation approaches are suitable to predict transverse shrinkage and transverse bending
- Shrinkage force approach is more suitable to predict the longitudinal shrinkage and longitudinal bending
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
Future work
18
- Further evaluation of approaches - Application to large, real, welded structures in Construction Machinery
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016
19
Thank you for your kind attention!
Questions?
3rd Nordic Conference on Design and Fabrication of Welded Structures Stockholm Waterfront Conference Center, 29 Sept2016