Magic Bullet NutriBullet Pro Activator Replacement...Magic Bullet NutriBullet Pro Activator Replacement This guide will teach you how to remove the activators from your Magic Bullet

Magic Bullet NutriBullet Pro ActivatorReplacement

This guide will teach you how to remove the activators from your Magic Bullet NutriBullet Pro if youhave determined they are faulty.

Written By: Malcolm Smith Fraser

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 7

INTRODUCTION

If your Magic Bullet NutriBullet Pro won't activate, and you have determined that the activators arethe culprit, follow this guide to replace them. This guide will work to replace all three activators.

TOOLS:Tweezers (1)Phillips #1 Screwdriver (1)Phillips #2 Screwdriver (1)

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 7

Step 1 — Magic Bullet NutriBullet Pro Disassembly

To start the disassembly of the Magic Bullet NutriBullet Pro you will begin from the bottom.

Flip the device over to the bottom.

Unscrew the four 1 cm screws using #2 Phillips Head Screwdriver.

Remove the loose bottom portion of the device by pulling up from the bottom.

Step 2

Unscrew the two 1 cm screws holding down the power cord using the #2 Phillips HeadScrewdriver.

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 7

Step 3

Unscrew the three 1 cm screws on the device circled on the screws pictures using the #1 PhilipsHead Screwdriver.

Lift off the grey plastic piece off.

Slide off the silver metal piece.

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 7

Step 4

Flip the device over.

Remove the three rubber seals covering the screws by pulling the components upward with thetweezer.

Unscrew the three 16 mm screws using the #2 Phillips Head Screwdriver.

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 7

Step 5

Pull off the casing from the device.

Step 6 — Activator

Remove the two 8 mm screws using the #2 Phillips Head Screwdriver while holding the activator inplace.

There are three separate activators with two screws each.

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 7

To reassemble your device, follow these instructions in reverse order.

Step 7

Be careful of the spring flying out.

Lift activator out of the Magic Bullethousing while holding the spring withtweezers.

Magic Bullet NutriBullet Pro Activator Replacement Draft: 2016-12-22Guide ID: 72307 -

This document was generated on 2019-10-04 12:16:34 PM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 7 of 7