lipLEDs ™ 8350 Series DRY LOCATION UL2108, CSA C22.2#9 UL8750, CSA250 VOLTAGE 24VDC L70 LED LIFE 60,000 hrs. DIMMING DMX-512 LAMP TYPE Color Tuning LEDs lipLEDs TM Series is a field cuttable system designed with long life, energy efficient LEDs that result in low maintenance installations. lipLEDs TM is excellent to illuminate areas for cove lighting, accent lighting, backlighting, and other indirect lighting applications. Lighting for the Professional Designer FIELD CUTTABLE SYSTEM Color Tuning 8W 24VDC RoHS COMPLIANT 10-DAY MADE IN USA
11
Embed
MADE IN - California Accent Lighting · Controller 3.38” 3.38” DMX Mode - Set DMX address to be used with DMX 512 Standard Protocol 1. DMX Addressing: Set DMX address using the
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
2019
.02.
21
CALIFORNIA ACCENT LIGHTING, INC. | calilighting.com
lipLEDs™ 8350 Series
DRY LOCATION UL2108, CSA C22.2#9UL8750, CSA250
VOLTAGE24VDC
L70 LED LIFE60,000 hrs.
DIMMINGDMX-512
LAMP TYPE Color Tuning LEDs
lipLEDsTM Series is a field cuttable system designed with long life, energy efficient LEDs that result in low maintenance installations. lipLEDsTM is excellent to illuminate areas for cove lighting, accent lighting, backlighting, and other indirect lighting applications.
lipLEDs™ series is a 24 Volt system that requires a 24VDC (secondary side) transformer. The standard primary side voltage on our transformers is 120V or 277V. Consult factory for other primary side voltages.
SERIES OPTICS WATTS PER FOOT DIMMING LED DRY FINISH
LLED8350*3Clear Lens (CL)*4
8 Watts (8W) DMX-512 (DMX) 2400K-6400K Color Tuning
(LED-CT)
Indoor (DRY) Natural Silver (NA)*2
LLED8350-CMW Polished (PA)
LLED8350-LSR50% Semi-Frosted Lens(SF)
White (WH)
LLED8350-LW Satin (SA)
LLED8350-LWR100% Frosted Lens (F)
Black (BK)
LLED8350-UC*3 Green (GN)
LLED8350-WRC Red (RD)
LLED8350-WRCR Silver (SR)
*1 Maximum run based on 4 amps for class II applications 11’ (8W)*2 Standard Finish: Natural Silver if left blank (Finish does not apply to LLED8350)*3 No optics available*4 Standard Lens - Clear if left blank
** Class II 24VDC TRA16-E, TRA25-E, TRA40-E, TRA60-E, TRA-80E, TRA90-E
Technical Requirements For Control Equipment (0-10V Protocol)
• The output current level of the dimmable driver is controlled by DC voltage (0-10V) applied to the control terminals (blue and white). The light output of LEDs is controlled by the amount of output current from the dimmable driver.
• The control device must be capable of sinking a DC current flow from the driver. The maximum amount under any condition is 500 microamps (uA) per driver.
• The control terminals of the dimmable driver are isolated from the power lines and are suitable for use as Class 2 wiring. Multiple drivers are desired for use with same control device, the control terminals may be connected in parallel in a bus configuration.
• Since the control bus is Class 2 wiring, all control devices that are connected to the power line must have proper isolation between the power line and the control terminals/bus.
• The control device, which intends to control more than one dimmable driver, must be capable of sinking the total current supplied to control bus by the drivers.
• If the control terminals/bus is shorted in any case, the current on the control terminals/bus will be 500 microamps (uA) per driver maximum.
• If the control terminals are opened, the voltage on the control terminals will then be 10V ± 0.5 volt. As a result, dimmable driver supplies maximum output current to LEDs under this condition.
• The driver is intended for use with control voltages between 0 and 10 VDC. The control equipment must not impose a voltage greater than 11 V peak maximum on the driver control terminals.
CALIFORNIA ACCENT LIGHTING, INC. | calilighting.com
DESIGN GUIDELINES
120-277VAC Input
Signal Terminator(DMX-RJ45-TERMINATOR)
24VDC Output
RJ45 EthernetConnection
White
Brown
Yellow
120V Input
DMX Decoder(DMX-CT-5A)
TRAXXX-E-UNV-24VDC-10V(Required, Not Included)
(Must use electronic transformer)
Wall Controller(DMX-CT-128C)(Not Included)
LLED8350
SPECIFICATIONS
PACKAGE Controller, CD-ROM, USB cable, connector block
OS REQUIREMENTS Mac OS X 10.6/10.7/10.8, Windows XP/Vista/7/8 32/64 bit, and USB 2.0
SOFTWARE Easy Stand Alone, ESA2 (PC & Mac)
VERSIONS Black or white glass design
CONNECTIONS Power (2 pins), DMX, (3 pins), Port (2 pins), Micro USB
POWER 5.5V to 12VDC (AC/DC adapter in option). Max 5.5V with USB
CERTIFICATIONS EC, EMC, ROHS, ETL, UL
KEYPAD 86x76x10mm, 110g
PACKAGE 140x135x50, 365g
USE Environment IP20. Temperature 0°C to 50°C
AVAILABLE MEMORY
CHANNELS CHANNELS
8 1691
16 1011
32 557
48 383
64 291
80 233
96 195
112 166
128 145
RGB Controller
• DMX Standalone Controller with glass face (128 channels)• 3 touch-sensitive buttons (on/off/miode, previous, next)• Up to 24 dynamic or static scenes (8 first visualized by an LED)• Live intensity and color settings• Programmable through included USB cable and control software• Compatible with any DMX fixture or DMX LED driver• Ready to use (pre-loaded with 8 scenes and 42 RGB fixtures)• Latest ARM CPU technology• Customized design for OEM, wall mountable• One dry contact trigger port on PCB
Controller
3.38”
3.38”
DMX Mode - Set DMX address to be used with DMX 512 Standard Protocol
1. DMX Addressing: Set DMX address using the Dip Switches on the DMX-RGBW-5A. 2. Use Binary Code to set Address.3. Connect to a DMX Master Controller such as DMX-RGB-128C or Butler XT-2 to control RGB Functions.