This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Crendon Machinery Parts All Machinery (Not Squirrel) 8 July 2022
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 2
NetWizz Top – Std & Hi-Lift
Replacement Centre Mast double reinforced for Standard NetWizz – ZNWCM*
Netwizz std & slim heavy duty top loop can make 8.5m or 5.5m. 8.5m made from 8 sections, 5.5m made from 5 sections, clamps to same mast – ZNWHDTL8.5EK
Old Style 5m Top Loop Complete std NetWizz – left half & right half ZNWSTLC5*
Centre top mid arm for standard NetWizz – ZNWCTMA*
Extension arm for Std & Hi-lift NetWizz -ZNWSHLEXTA*
End arm for Slim, Std & Hi-lift NetWizz – ZNWEA*
NetWizz Top - Hi-Lift & Swivel Head
Mid-mast eye for Hi-lift & Swivel head NetWizz (up to 12-2016) – ZNWHLMME*
Extension for mid-mast eye for Hi-lift & swivel head (up to 12-2016) – ZNWHLEME*
bottom-mast eye for Hi-lift & Swivel head NetWizz with 3 rollers (from 2017) – ZNWHLSBME*
NetWizz Top - Hi-Lift
Telescopic extension for Hi-lift NetWizz – ZNWHLTE*
Top arm base for Hi-lift NetWizz - ZNWHTLTAB
NetWizz Top - Hi-Lift Swivel Head
Telescopic extension for Hi-Lift swivel head NetWizz swivel plate fixed angle (up to 12-2016) – ZNWHLSTE* Telescopic extension for Hi-Lift swivel head NetWizz swivel plate adjustable angle (from-2017) – ZNWHLSTSA*
Side arm for Hi-Lift swivel head NetWizz – ZNWSA*
Extension arm for Hi-Lift swivel head NetWizz – ZNWHLSEA*
End arm for Hi-Lift swivel head NetWizz – ZNWEASH
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 3
NetWizz Top - Hi-Lift Swivel Head
End net removal arm for Hi-Lift swivel head NetWizz – ZNWHLSRA*
Centre top arm eye for Hi-Lift swivel head NetWizz with 2 rollers – ZNWHLSCTAE*
Arms pins for Hi-Lift swivel head NetWizz ZNWHLSAP
Mast Rotating around handle assembly, High-Lift & swivel head NetWizz (from 2017) after ZNWHLMRC Mast Rotating around handle assembly, High-Lift & swivel head NetWizz (up to 2016) after ZNWHLMR*
NetWizz Top – Slim & Manual
Centre top mid arm for NetWizz slim & manual – ZNWSCTMA*
End arm for Slim, Std & Hi-lift NetWizz – ZNWEA*
Mast for NetWizz slim & manual – ZNWSM*
NetWizz Slim – Components
Centre Mast for NetWizz slim & manual 50MGP – ZNWSCM*
Wand connecting rod NetWizz Slim – ZNWSWCR*
NetWizz Slim Female drive– ZNWSFD*
NetWizz Slim mast pole rotation assy– ZNWSMPRA*
NetWizz Slim Spindle cover– ZNWSCS $578 + GST
NetWizz – Components Std, Hi-Lift & Swivel Head
Spindle cover (1.05m) for Standard & Hi-Lift – ZNWSC
Drive Hub & Bearing for Spindle Cover– ZNWSCDHB* $71.82 +GST
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 4
Worm drive RV90-20DZ, 20:1, input hyd motor flange, Ø35 output shaft (from 2023) – GBRV90-20DZ
Hyd motor for worm drive gear box 80cc 2blt flange, 1" straight shaft, 1/4" keway,7/8UNF ports, no case drain, BMPH-80-H2-K-S-B-O (from 2023) - BMPH80H2KSBO
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 8
NetWizz – Hydraulics Hydraulic Motors – TPF BMER-2 High performance 3,000 psi shaft seals, Low speed & four bearings
Hyd motor TPF 375cc BMER-2-375-MS-RW 6blt flange 1” shaft 7/8UNF ports (from 2019) - MHC BMER23756B1S
Seal kit for BMER-2 hydraulic motor, rated to 200 bar – MHCBMER2-SK
Shaft seal HP BMER-2 hydraulic motor rated to 200 bar, 35 id x 48 od x 4.72 wide – MHCBMER2SS200
Shaft seal HP BMER-2 hydraulic motor special made rated to 300 bar, 35 id x 48 od x 4.72 wide – MHCBMER2SS300
Woodruffe Key 1x ¼" – KW1/4X1
NetWizz – Hydraulics Hydraulic Motors – TPF BMRS
Hyd motor TPF 395cc BMRS400 2blt flange 1” shaft 7/8UNF ports (from 2000 – 2019) – MHCBMRS4002B1S Hyd Motor TPF Parts
Shaft seal HP BMRS hyd mtr 28.56×42x5.5 – MHCBMRSPSS
Dust seal HP for BMRS hyd mtrs – MHCBMRSDS
Shaft bearing kit for BMRS hyd mtrs - MHCBMRSSB
Seal kit for BMRS-N hydraulic mtrs - MHCBMRSSK
Woodruffe Key 1x ¼" – KW1/4X1
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 9
NetWizz – Hydraulics
Hyd Motor White RS Parts
Seal Kit WHITE RS (Short) picture left – MWRSSKS Seal Kit WHITE RS (Full) picture right – MWRSSKF
Thrust Bearing WHITE HS/RS – MWRSTB
Key steel 1x ¼" – KS1/4X1” Hyd Motor Danfoss Parts
Seal kit Danfoss OMP 151-1279 – MHDOMP80SK
Seal kit Danfoss OMR 151-1280 – MHDOMRSK
Dust seal for OMP/OMR 151-131300 – MHDOMPDS
NetWizz – Hydraulics
Shaft seal HP for OMP/OMR 633B036100 – MHDOMPSS Hyd Motor Senwei Parts
Thrust bearing & washer OMRS- MHCOMRSTBW
Needle roller bearing OMRS – MHCOMRSNRB
Bearing for shaft OMRS – MHCOMRSSB
Seal kit for Senwei OMRS hyd mtrs – MHCOMRSSK Hyd Motor M&S
Hyd mtr HR400 1" shft 7/8 PORT 2B Fl – MHHR400C4UC
Seal kit MLHR motors 1¼" shaft – MHMLHRSK Seal kit HP motors – MHHPSK Seal kit HR motors – MHHRSK
Woodruffe Key 1x ¼" – KW1/4X1
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 10
NetWizz – Hydraulics
Flow Control Vlv ITI 16GPM ½” CH - VFC16G12NRCH
O-ring for Prince Flow control valve (up to 2010) – ORBS116 O-ring for ITI Flow control valve – ORBS020
Rod end 12mm Female NetWizz Slim (from -2017) –BHBJM12F
Rod end ½” UNF Male - Female NetWizz Slim (up to 12-2016) BHBJ12UNFCH
NetWizz slim Crank arm with rod ends - ZNWSWCL*
NetWizz slim mast base - ZNWSMB*
NetWizz Slim Female drive– ZNWSFD*
NetWizz Slim mast pole rotation assy– ZNWSMPRA*
NetWizz Slim Heavy duty – Parts
NetWizz Slim Spike Ø45 for drive & bearings then Ø43 made from 40Cr square drive, with motor drive cupping, pully, Ø45 bearings & housings complete ZNWSSCEK
NetWizz Slim Spike Ø45 for drive & bearings then Ø43 made from 40Cr square drive, hole for pully & square drive– ZNWSSEK
NetWizz Slim pully ID Ø45 1BX90 for drive -ZNWSPB90EK
NetWizz Slim Hyd motor to Spike drive with hole to match spike square drive– ZNWSHMSPWKK
NetWizz Slim Spike drive to spinal cover– ZNWSDSCEK
NetWizz Slim Spike drive tapered pin– ZNWSDTPEK
NetWizz Slim heavy duty sensor arm– ZNWSHDSAEK
NetWizz Slim heavy duty wand crank arm connecting link complete with 12mm rod ends– ZNWSHDWCAEK
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 13
NetWizz Slim Wand crank pulley 1B x 350 complete with bearings & bolts– ZNWSWCPB350EK
NetWizz Slim tension idler 1B x 75 flat complete with bearings & bolts– ZNWSTIB75CEK
NetWizz – Stickers All
x2 Pt# DSNWLOGO
x2
DANGER
Keep clear of all moving parts as they may cause
serious injury.dcc x3
Pt# DSDANGER Pt# DSSAFETYMAN Pt# DSNWCAUSLOP Sticker NetWizz Slim sticker set -DSNWSSET Sticker NetWizz Std sticker set -DSNWSTDSET Sticker NetWizz HiLift sticker set –DSNWHLSET Sticker NetWizz HiLift Swivel Head sticker set –DSNWHLSHSET
NetWizz – Stickers Slim
DSNWSLIM
S limAuto Tens ion
nsat
1
2ApplyingNetting
Netting Roll
nwsuwn
1
2
3
4
5
RetrievingNetting
Sensor
Wand
Netting Roll
Roll must rotate CLOCK WISE when viewed from rear.
nwswun Pt#DSNWSAN Pt# DSNWSRN
Weekly
grw x4 Dailyold x6 x2 Pt# DSNWSRL
NetWizz – Stickers Std, High Lift & Swivel Head
Pt# DSNWCAUTRA
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 14
Pt# DSNWSRNASS Pt#DSNWRN6
Pt#DSNWRM
Netwizz – Stickers Std Mast
-PT# DSNWSTD
DSNWAPPNET
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 15
PT# DSNWRETNET
NetWizz – Stickers Std Mast
Pt# DSNWHLA1 Pt# DSNWAN3
Pt# DSNWRN2 Pt# DSNWRN3
Pt# DSNWRN4 Pt# DSNWRN5
Pt# DSNWSRN6 Pt# DSNWRN7
Pt# DSNWRN8
Pt# DSNWSRN8
Pt# DSNWRLM
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 16
NetWizz - Stickers High Lift
SNWHLword
High Lift Mast Auto Tension
Pt# DSNWHLWORD
SNWHLR0
1
3
2
4
9
5
6
87
Wand
RetrievingNetting
Netting Roll
CAUTION NEVER CLIMB THE MAST TO THREAD NETTING,
USE THREADING ROPE
NEVER WIND UP NETTING WITH OUT USING THE AUTO SENSOR
Nettin
g Bra
ke Up
Sensor On
Net
Wiz
z H
igh
Lift
Sw
ivel
Hea
d A
uto
Ten
sio
n
Pt# DSNWHLR0
Net
Wiz
z H
igh
Lift
Aut
o T
ensi
on
Netting Roll
1
2
3
4ApplyingNetting
Sensor Off
Netting Brake Down
CAUTION NEVER CLIMB THE MAST TO THREAD NETTING,
USE THREADING ROPESNWHLA0
Pt# DSNWHLA0
NetWizz - Stickers High Lift
SN
WH
LA1(1) APPLYING NETTING
1: Slide brake out & lower onto roll to reduce any over-run. Pt# DSNWHLA1
Pt# DSNWHLA2
(3) RETRIEVE NETTING1:
2:3:
Feed over the top of mast arms. Bottom mast eye.
Then through this eye.
SN
WH
LR3
Pt# DSNWHLR3
(4) RETRIEVE NETTING4: Feed through this sensing eye. S
NW
HL
R4
Pt# DSNWHLR4
(5) RETRIEVE NETTING5: Feed through this bottom eye. S
NW
HLR
5
Pt# DSNWHLR5
6 RETRIEVE NETTING6:
7:Feed through this wand eye.
Wrap around spindle. SN
WH
LR6
Pt# DSNWHLR6
Pt# DSNWHLR7
SNWHLR8
(8) RETRIEVE NETTING8: spindle motor rotate this way.
Pt# DSNWHLR8
(9) RETRIEVE NETTING9: Auto sensor is unlocked by
raising this handle and pushing the latch lever.
To lock off, raise this handle and pull the latch lever. SNWHLR9 Pt# DSNWHLR9
Pt# DSNWHLR10
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 17
NetWizz - Stickers High Lift
Pt# DSNWHLEML
NetWizz - Stickers High Lift
Pt# DSNWHLSWEBME
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 18
NetWizz - Stickers High Lift Swivel Head
Netwizz Hi Lift Mast Swivel Head - Pt# DSNWHLSWORD
SNWHLSR0
1
3
4
2
5
10
6
7
98
Wand
RetrievingNetting
Netting Roll
CAUTION NEVER CLIMB THE MAST TO THREAD NETTING,
USE THREADING ROPE
NEVER WIND UP NETTING WITH OUT USING THE AUTO SENSOR
Nettin
g Bra
ke Up
Sensor On
Net
Wiz
z H
igh
Lift
Sw
ivel
Hea
d A
uto
Ten
sio
n
Pt# DSNWHLSR0
Net
Wiz
z H
igh
Lif
t Sw
ivel
Hea
d A
uto
Ten
sion
Netting Roll
1
2
3 4
5ApplyingNetting
Sensor Off
Netting Brake Down
CAUTION NEVER CLIMB THE MAST TO THREAD NETTING,
USE THREADING ROPESNWHLSA0
Pt# DSNWHLSA0
NetWizz - Stickers High Lift Swivel Head
SN
WH
LSA
1(1) APPLYING NETTING1: Slide brake out & lower onto
roll to reduce any over-run. Pt# DSNWHLSA1
SN
WH
LS
A2
(2) APPLYING NETTING1:
4:
2:3:
5:
Lower net brake. Feed through this eye first,
Then
Through bottom mast eyeThrough telescopic mast eye.
over the top of mast arms. Pt# DSNWHLSA2
(4) RETRIEVE NETTING1:
2:
4:3:
Feed over the top of mast arms. Through telescopic mast
Bottom mast eye. Then through this eye.
eye.
SN
WH
LSR
4
Pt# DSNWHLSR4
(5) RETRIEVE NETTING5: Feed through this sensing eye. S
NW
HL
SR
5
Pt# DSNWHLSR5
(6) RETRIEVE NETTING6: Feed through this bottom eye. S
NW
HLS
R6
Pt# DSNWHLSR6
7 RETRIEVE NETTING7:
8: Feed through this wand eye.
Wrap around spindle. SN
WH
LSR
7
Pt# DSNWHLSR7
SNWHLSR8
(8) RETRIEVE NETTING8: spindle motor rotate this way.
Pt# DSNWHLSR8
(9) RETRIEVE NETTING9: Lock spindle motor in over bolt,
to unlock lift over. SNWHLSR9 Pt# DSNWHLSR9 (10) RETRIEVE NETTING
Auto sensor is unlocked by raising this handle and pushing
the latch lever. To lock off, raise this handle and
pull the latch lever.
10:
SNWHLSR10 Pt# DSNWHLSR10
Pt#DSNWHLSR11
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 19
NetWizz - Stickers High Lift Swivel Head
Pt# DSNWSWHTAS
Pt# DSNWRM
NetWizz - Stickers High Lift Swivel Head
Pt#DSNWHLSHEML
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 20
NetWizz - Stickers High Lift Swivel Head
Pt# DSNWHLSWEBME
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 21
SADIE - Single sided front mount Vineyard & Orchard
Rubber flap 390mm long for older Sadie’s each – ZSRF390* $23.00 + GST
Rubber flap 540mm long for new Sadies each – ZSRF540* $26.00 + GST
Bristle 5mm x 5mm quad section black set (8) (up to 2020) – SADIE – ZSBS *
Bristle 5mm x 5mm quad section black round set (5) – SADIE (from 2021 on) – ZSBR *
Chock, SADIE Bristle (up to 2020) – ZSBC
Rubber flap KIT for old Nylon SADIE 8+hl – ZSRFK
Holders for Rubber Flaps single Sadie (8) – ZSKRF
SADIE - Single sided front mount Vineyard & Orchard
Bush, Nylon - 4 per SADIE (for all 1” pin up to 2021) –NB1CH
Sadie single Sided Front Mount bronze bush, ID Ø30 x 34 OD x 40 long, 2 in each pivot & Hyd ram total required 6 ; (from 2021 on) – ZSBB30X34X40EK
Wedge Orchard/Sgle V'yard Sadies – ZSOW*
SADIE - Single sided front mount Vineyard & Orchard
Front skirt complete Orchard & Vineyard Sadie – ZSOFS*
Orchard Sadie spinning head frame only (steel frame no components) (up to 2020) – ZSOSH
Orchard Sadie spinning head frame only (steel frame no components) (from 2021) – ZSSOSSHFEK
Orchard Sadie head (steel frame no components) (up to 2020) – ZSOHF*
Orchard Sadie head with (BM5 125cc hyd motor tapered shaft, 4 bolt square flange), bolts (from to 2021) – ZSSOSHWMBEK
Orchard Sadie top head shield (up to 2020) - ZSOTHS
Orchard Sadie head assy: flaps, bristles, motor, spinning head, frame back to the shear-bolt bracket. No hoses (up to 2020) – ZSONH*
Sadie Vineyard Hydraulic motors, BM5 Like Hyd
Sadie Double Sided Front Mount; Like Hyd motors BM5 100cc with Ø31.75, 1:8 taped shaft, 8mm keyway, 4 bolt flange, 7/8UNO ports (from 2022 on) This is what we use now has - 3,500 psi shaft seals, & big tapped bearings – MHCBM51004BTS
Sadie Vineyard - Hydraulic motors TPF BMRS
Hyd motor for all vineyard Sadie’s, TPF 100cc BMRS100 2blt flange Ø31.75, 1:8 taped shaft, 8mm keyway, 7/8UNF ports (double sided & single sided Sadie’s from 2020) – MHCBMRS1002BT2
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 24
Hyd motor for all vineyard Sadie’s, TPF 100cc BMRS100 2blt flange 1” shaft 7/8UNF ports (double and Single sided Sadies after 2005 up to 2019) (up to 2020) – MHCBMRS1002B1S
Hydraulic Motors – TPF BMRS Parts
Shaft seal HP BMRS hydraulic motor 28.56 × 39 x 5.5 – MHCBMRSHPSS
Dust seal HP for BMRS hydraulic motor – MHCBMRSDS
Shaft bearing kit for BMRS hydraulic motor - MHCBMRSSB
Seal kit for BMRS-N hydraulic motor - MHCBMRSSK
Seal for Shuttle Check valve on BMRS-N hydraulic motors grade 90 (4 required per motor) – ORM10X2
Sadie Orchard Hydraulic motors, BM5 Like Hyd
Sadie Double Sided Front Mount; Like Hyd motors BM5 125cc with Ø31.75, 1:8 taped shaft, 8mm keyway, 4 bolt flange, 7/8UNO ports (from 2022 on) This is what we use now has - 3,500 psi shaft seals, & big tapped bearings – MHCBM51254BTS
Sadie Orchard Hydraulic motors TPF BMER-2
Hyd motor for all orchard single sided Sadies 125cc BMER125 7.4cc, 1 ¼” tapered shaft orchard single sided Sadie’s (from 2020 - 2021) – MHCBMER21256B11
Hyd mtr for all orchard single sided sided Sadies 125cc BMER125 7.4cc, 1 ¼” straight shaft (WHITE replacement) (up to 2020) - MHCBMER125
Hydraulic Motors seal kit – TPF BMER-2
Seal kit for BMER-2 hydraulic motor, rated to 200 bar – MHCBMER2-SK
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 25
Shaft seal HP BMER-2 hydraulic motor rated to 200 bar, 35 id x 48 od x 4.72 wide – MHCBMER2SS200
Shaft seal HP BMER-2 hydraulic motor special made rated to 300 bar, 35 id x 48 od x 4.72 wide – MHCBMER2SS300
Shaft Wiper seal HP BMER-2 hydraulic motor, 57.15 id x 35 od x 6.1 wide – MHCBMER2DS Old Orchard Sadies pre 2013
White RE series
Seal Kit WHITE RE (Short) – MWRESKS Seal Kit WHITE RE (Full) – MWRESKF
SADIE - Double sided Vineyard
Rubber flap 390mm long for pre 2002 older Sadies – ZSRF390 $23.00 + GST
Rubber flap 460mm long for 2020 & 2021 double sided front mount Sadie’s – ZSRF460 $25.00 + GST
Rubber flap 540mm long for 2002 & onwd Sadies – ZSRF540 $26.00 + GST
Std gas strut 500N-375 Sadie – GST500N375
Stainless Steel gas strut 600N-375 Sadie – GST600N375SS
Wheel 4.10-3.50-4" air free wheel, 73mm wide tread, welded rim hot dip galvanising, with 6004 bearings & spacer, no bolt axle V'yd Sadie - ZVS4WS* Wheel 4.10-3.50-4" air free wheel, 73mm wide tread, welded rim hot dip galvanising, with 6004 bearings & spacer, with bolt axle V'yd Sadie - ZVS4WSA*
Dust cover wheel seal protector for 4” wheels (on left) – ZVSDCSW* 50mm º Washer for seal protector for 4” wheels (centre) 16mm Washer for bearing for 4” wheels (right)
Axle bolt kit for 4” wheels –
Trailing wheel leg Dble Front-mount Sadie (state inside or outside) – ZVSDFMTL*
Small wheel arm (state L/H or R/H) Double Front-mount Sadie – ZVSDFMFWA*
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 26
Small wheel arm (state L/H or R/H) Dble Multi-mount Sadie – ZVSDMMSWA*
SADIE - Double sided Vineyard
Front 8" wheel puncture resistant (tyre, rim, tube, tyre sealant) for Sadie pre 2013– ZVS8WHTPR
Front wheel 16-650-8” 30mm centre air free PU filled - Sadie 2013 and after – TRW16*650-PUCH Front wheel seal protector 30mm centre wheel 2013 and after – BWZFM27X60X30X4
SADIE Tines – for Double and single sided Sadies
Vineyard Sadie single sided with tine & holder right hand side in picture
Sadie with tine & holder right hand side in picture Bolts requires - 60x10 if using with 2 rubber flaps, 50x10 if using with 1 rubber flap
Sadie tine Ø8mm spring 380 long, right and left hand. Right hand as above - ZVSSTR $21.45 + GST Left hand – ZVSSTL $21.45 + GST
Sadie tine clamp must be used to hold tine on pictured on left, requires Right hand as above – ZVSTCBR $28.00 + GST Left hand – ZVSTCBL $28.00 + GST
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 27
SADIE - Double sided Vineyard
Spinning head - pre 2002 Double Multi mount Sadie -ZVSDSSHO*
SADIE - Double sided Vineyard
Spinning head 2002 -2020 Double Multi & front mount Sadie - ZVSDSSHO2002*
Spinning head 2020 & onward Double front mount Sadie with Ø31.75, 1:8 taped shaft, 8mm keyway, - ZVSDSSHO2020T
Pin set for Double Multi-mount Sadie (up to 2020) - ZVSDMMPS*
Double Multi-mount Sadie double 1” pin with bolt & grease nipples (up to 2020) - ZVSDARMPIN
Bush, Nylon - 40 required per SADIE (up to 2020) –NB1CH
Sadie single Sided Front Mount bronze bush, ID Ø30 x 34 OD x 40 long, 2 in each pivot & Hyd ram total required 6 ; (from 2021 on) – ZSBB30X34X40EK
Boss, 1"Ø, ¼key, 2x3/8 grub V/Sadie drum - ZVSDB*
Head height arms & pins Double Multi mount Sadie after (up to 2020) ZVSDPHAA
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 28
SADIE - Double sided Vineyard
Head height arms with brackets & pins complete Double Multi mount Sadie after (up to 2020) ZVSDHHASC*
Rock shield side guard complete Double Multi mount Sadie – ZVSDMMRSSG*
Centre curtain Rock shield Double Multi mount Sadie - ZVSDMMRSCC*
Head wheel assay bracket Double Multi mount Sadie after 2004, each – ZVSDMHWAB-04*
Head wheel assay bracket Double Multi mount old Sadie year 2002 – 2004, each – ZVSDMHWABB04
Head wheel assay bracket Double Multi mount old Sadie year 2000 – 2002, each – ZVSDMHWABB00
SADIE - Double sided Vineyard
Upgrade kit - for pre-2001 model Double Multi mount Sadie – (retro-fit heads etc) - ZVSDRF2001* Head mtr bracket Double Multi mount Sadie die – ZVSDHMB* Trailing wheel leg Double Multi mount Sadie – ZVSDMMTWL*
Double Sadie Multi Mount Air free wheels to swing back assay compl – Double MM (up to 2020) ZVSDMMW-S*
Double Sadie Moulty Mount; Air free wheels, Head frame, long rubber flaps, Hyd motor, (up to 2020) ZVSDM………..*
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 29
SADIE - Double sided Vineyard Front Mount
Outside width arms double front mount Sadie with 2 pins- (up to 2019) f- ZBSDFMWPA
Head spring assembly Double front mount Sadie - ZVSDFMHSA*
Head spring Double front mount Sadie - 1.5"ODx0.2830 wire x 400mm long - SBC1.5OD0.283X4
Ball Joint ½” UNF (Male x Female) studded – BHBJ12UNFCH
Ball Joint 12mm (female x female) – BHBJM12F
SADIE - Double sided Vineyard Front Mount
Sadie Double Sided Front Mount; Hyd with arms ram, 200x 50x25 x with double piolet check valves – (from 2019 on) ZVSDSFMWAR200X50X25EK
SADIE - Double sided Vineyard Front Mount
Sadie Double Sided Front Mount; Like Hyd motors BM5 100cc with tapered shaft, 4 bolt flange, 7/8UNO ports (from 2022 on) – MHCBM51004BTS
Sadie Double Sided Front Mount head frame to take 4 bolt motor flange, state right hand or left hand required (from 2022 on) – ZVSDSFMMHF4BEK
Sadie Double Sided Front Mount; side swing back arm & bottom universal joint with 1 x Ø30 pin, state right hand or left hand required (from 2022 on) - – ZVSDSFMSSBABUJEK
Sadie Double Sided Front Mount arms pin; Ø30 pin x 189 grip length, total 10 required (from 2022 on) ZVSDSFMAP30X189EK
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 30
SADIE - Double sided Vineyard Front Mount
Sadie Double Sided Front Mount head universal joint pin; Ø30 pin x 189 grip length, total 4 required for head universal joint. (from 2022 on) ZVSDSFMHUJ30X189EK
Sadie double sided Front mount complete side assembly pin; Ø30 pin x 403 grip length, total 2 required (from 2022 on) – ZVSDSFMCSA30X403EK
Sadie Double Sided Front Mount width ram pin, Ø20 pin x 74 grip length, total 2 required (from 2022 on) – ZVSDSFMWR20X74EK
Sadie Double Sided Front Mount; width ram pin, Ø20 pin x 158 grip length, total 2 required (from 2022 on) – ZVSDSFMWR20X158EK
Sadie single Sided Front Mount bronze bush, ID Ø30 x 34 OD x 40 long, 2 in each pivot & Hyd ram total required 6; (from 2021 on) – ZSBB30X34X40EK
For accurate sweeping, insert pin in hole to match row centres.
2.1m
2.3m
2.5m
2.7m
2.9m
3.1m
3.3m
3.5m
3.7m
3.9m
2.2m
2.4m
2.6m
2.8m
3.0m
3.2m
3.4m
3.6m
3.8m
For accurate sweeping, insert pin in hole to match row centres.
sticker SADIE ...to match row centres R – DSSAROWWID sticker SADIE ...to match row centres L – DSSAROWWIDL Extend & contract SADIE arms when fully raised
Max. Hyd. Requirements - 35 lt/minSet flow control to approx # 8
Tyre pressure 30 P.S.I.KEEP CLEAR OF ALL MOVING PARTS sticker SADIE extend & contract arms ... – DSSAEXTARMS sticker SADIE when mounted to tractor... - DSSAMOU3PL sticker SADIE ...max hyd require
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 34
Bin Runner – Sprockets, chain & Axles
Sprkt 10 tooth x ¾ AS Ø1"B ¼"Key 2x5/16 grubs - SM10TX3/4AS1BCH * (up to 2018)
Sprkt 11 tooth x duplex ¾ AS Ø1"B ¼"Key 2 x 8mm grubs - SM11TX3/4ASD (From 2019)
Sprocket 13 tooth x duplex ¾ AS Ø1¼"B ¼"Key 2 x 8mm grubs - SM13TX3/4AS1.25 (From 2020 on)
Sprocket T/fit duplex 21Tx ¾ AS 2517 – STFD21TX3/4-251
Sprocket T/Fit simplex 21Tx¾ AS 2517 – STFS21X34BS-251
Bush, Taperfit 2517, Ø1¾" – STFB2517-13/4CH * (up to 2018)
Bin Runner keyed Ø1-3/4” shaft – ZBRKS* (up to 2018)
Bin Runner keyed Ø45mm shaft – ZBRKSM* (From 2019)
Chain Trans 3/4"AS duplex (60-2) – CT3/4DCH
Duplex Chain joiner link 3/4"AS duplex (60-2) – CTCL3/4DCH
Chain Trans ¾”AS simplex (60-1) – CT03/4CH
Steel locking collar 2.25” with 4 x grubs - SC2.25
Steel collar for Ø75mm x 40 long shaft, 4 x 12mm grub screws – SC110X75X40
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 35
Bin Runner – Floor wear strips
8mm thick (from mid 2021) 4 bin Runner Floor HDPE wear strips 50mm x 8mm x 4.8m for & 80 x counter sunk screws, (from mid-2021) – ZBRWS8X50X4.8 5 bin Runner Floor HDPE wear strips 50mm x 8mm x 9.6m for & 100 x counter sunk screws, (from mid-2021) – ZBRWS8X50X9.6 6 bin Runner Floor HDPE wear strips 50mm x 8mm x 14.4m for & 120 x counter sunk screws, (from mid-2021) – ZBRWS8X50X14.4
6mm thick (before mid 2021) 4 bin Runner Floor HDPE wear strips 50mm x 6mm x 4.8m for & 80 x counter sunk screws, (from mid-2021) – ZBRWS4* 5 bin Runner Floor HDPE wear strips 50mm x 6mm x 9.6m for & 100 x counter sunk screws, (from mid-2021) – ZBRWS5* 6 bin Runner Floor HDPE wear strips 50mm x 6mm x 14.4m for & 120 x counter sunk screws, (from mid-2021) – ZBRWS6*
Bin Runner - Hubs & Axles 1.5t
(From 2010 to 2015) Hub/axle assy FORD 1.5 ton complete (5x1/2UNF-114.3PCD 2"x12SQ)-AHA5X12+2X12
ss
Dust Cap for 1.5T Ø50mm – AHDCCH
Bin Runner side guide up rights 25 pipe with 24 rod in centre - ZBRSA*
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 36
Bin Runner - Hubs & Axles 2.25t
(From 2015 -mid 2021) Hub/axle assembly, FORD PDC, 2.25 ton complete (5 x 1/2UNF - 114.3PCD 2" SQ x 14” long)-AHA5X12F2.5
Wheel bearing set, (2 x big bearing & seal) 2.5 ton FORD for hub/stub – BTWSF2.5 Wheel bearing big used 2 & cone BTWL68149/10 Shaft seal OST21TB
Dust Cap for 2.5 ton Ø 59.4mm for large taped flange 2.5 ton hubs as pictured above – AHDC60
Dust Cap for 2.5 ton Ø 63mm for smaller square edge flange 2.5 ton hubs as pictured above – AHDC63
Wheel Stud & nut 1/2"-20UNF x 40mm – AHWS12-20UNF
Wheel Nut 1/2" (Ford) - AHWNF1/2
Bin Runner - Hubs & Axles 2.75t
(From mid 2021 this is what we are using now) Hub assembly, FORD PDC, 2.75 ton, (5 x 1/2UNF - 114.3PCD) complete with studs, nuts, big & small bearing, dust seal, hub cap-AHA5XF2.75
(From mid 2021 this is what we are using now) Axle, with washer split pin & nuts -AHA2X12F2.75
Wheel bearing set, (1 x big bearing 33008 & 1 x small bearing 33007 & seal 72x48x8) 2.75 ton FORD for hub– BTWSF2.75
Dust Cap for 2.75 ton Ø 61.8mm for large taped flange 2.75 ton hubs as pictured above – AHDC61.8
Wheel Stud & long nut 1/2"-20UNF x 45mm, knurled Ø12.5x10mm long – AHWS12-20UNFX45
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 37
Bin Runner - Wheels
Rim 14x5 black HOLDEN HT(before SN 11048) - TRR14X5
Rim 14x6 FORD white (after SN 11048) - TRR14X6WCH Tyre 215/75Dx14 8PR – TRT215X75X14-8P
Wheel complete Tyre & Rim; Rim 12”x8” ford PCD, 0mm offset, hot dip galvanised fitted with Tyre 25x10.00x12 8 ply – TRW25/10+8PRT
Tyre 25x10.00x12 8 ply AT Twill, load rated 1300kg each –TRT25x10-12-8PR
Wheel complete Tyre & Rim, 620mm Ø x 300mm wide x 12 ply, load 1200 kg each, (from 2018) ; Rim 12” x 9.5” ford PCD, 30mm offset, hot dip galvanised fitted with Tyre 26x12.00x12 12 ply – TRW26X12x12PRT
Bin Runner - Wheels
tyre 620mm Ø x 300mm wide x 12 ply, load 1200kg each, (from 2018) TRT26X12X12-12P
Tube 26x1200x12 (TR13) - TRTU26X1200X12
Rim Ø12” x 9.5”, PCD 5 x 114, hot dip Gall (2018 on) - TRR9.5x12HDG
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 38
Bin Runner - Bearings
Bearing 1-3/4” UC209-28S - BUC209-28CH
Bearing 45mm UC209 - BUC209
Bearing Hsg Flange FL209 2hole - BFL209CH
Chain idler pin 20mm (before SN 08038) – ZBRCIP20* Chain idler pin 25mm (after SN 08038) – ZBRCIP25*
Rear idler complete 25mm brg (after SN 08038) – ZBRRIC25*
Rear Chain idler one piece with 4x25mm (after mid 2021) – ZBRRIC1P25
Seal kit for 10x2x1" – RCHSK2X1 Seal kit for 8x2.5, 12x2.5x1.25" – RCHSK2.5X1.25 Hydraulic Rams – Baker parts pre 2008
Seal Kit 2.5"BX1.25” BAKER - RBSK2.5X1.25
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 40
Bin Runner - TPF BMER-2 Hydraulic motor
From late 2019 (This is what we use now has- 3,000 psi shaft seals, 4 heavy shaft bearings, very low internal leakage, high performance) With 1 1/4” shaft, 7/8”UNO ports, large 6 bolt flange, 250cc, 200 bar shaft seal - MHCBMER250MSRW
Hydraulic Motors seal kit – TPF BMER-2
Seal kit for BMER-2 hydraulic motor, rated to 200 bar – MHCBMER2-SK
Shaft seal HP BMER-2 hydraulic motor rated to 200 bar, 35 id x 48 od x 4.72 wide – MHCBMER2SS200
Shaft seal HP BMER-2 hydraulic motor special made rated to 300 bar, 35 id x 48 od x 4.72 wide – MHCBMER2SS300
Bin Runner - TPF BMRS Hydraulic motor
Hyd mtr 250cc 15ci BMRS250 2BF/1"/¼K/7/8U/200 –MHCBMRS2502B1S
Shaft seal HP BMRS hyd mtr 28.56×42x5.5 – MHCBMRSPSS
Dust seal HP for BMRS hyd mtrs – MHCBMRSDS
Shaft bearing kit for BMRS hyd mtrs - MHCBMRSSB
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 41
Bin Runner Stickers sticker BIN RUNNER Logo – DSBINRUNLOG
sticker MADE BY CRENDON 238x79 – DSCRENMACMADEBY
sticker SAFETY Read Owner’s Manual – DSSAFETYMAN
DANGER
Keep clear of all moving parts as they may cause
serious injury.dcc
sticker Keep clear of all moving parts – DSDANGER
Bin Runner Stickers Weekly
grw sticker Grease Weekly – DSGREWEE
Bin Trailer CapacityMaximum
Maximum towing speed loaded- 20 km/hr.
Never move the bin trailer when people are close to or
standing on it
load single layer of 750 kg bins.
Maximum towing speed empty- 40 km/hr.
btc
sticker Bin Trailer capacity - DSBTC
Bin Runner
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 42
2 & 3 Bin Trailer Hubs & Axles 1.5t (after 2010)
Hub/axle assy (5x1/2UNF-114.3PCD 2"x12SQ) – (after SN 11048) - AHA5X12+2X12
Whl brg set, seal FORD for hub/stub (after SN 11048) – BTWSF*
Visually check compressor V belt condition & tension & drain air tank etc
Visually check air, hydraulic & fuel system for leaks
Visually check the tyre pressures & tyre condition
Check the platform controls for function etc
Visually check the platform for and c lear any debris so that there are no tripping hazards & that gate systems all func tion fully etc
Visually check the Trel-Pick frame for loose/ missing parts, c racks & struc ture free from distortion etc
Visually check the work area for operational hazards (eg. Slope, power lines, pot holes, debris etc )
Visually check the picking bag/pruning tools etc (if applicable)
Ensure that the machine is maintained in a safe working order.
1. Safe Working Load per raised platform is 200kg (inc luding operator, tools & picking bag of fruit).
2. Safe Working Load for main platform is 2 tonne.
3. Maximum operating slope is 15°.
4. Bin trailers to a maxim um of 1 tonne can be towed behind the Trel-Pick
5. Operate in Fast Speed only when safe to do so.
6. Keep a safe distance away from power lines
7. Do not carry any loads outside the platforms other than the picking bag and picking trays provided.
Operating a) To start: Engine start/stop button is beneath
the steering wheel and the engine must be turned on (choke will be required if engine is cold). The Stop/Emergency stop button needs to be reset each time before restarting.
b) To drive the Trel-Pick: Push the hydrostatic lever to the required direc tion & the hydraulic speed will respond proportionally. Operate in Fast Speed only when it is safe to do so.
c ) The throttle is beneath the steering wheel. Operate in Fast Speed only when it is safe to do so.
d) Always apply the handbrake firm ly when the engine is not running.
e) Rear steering is foot ac tivated by the hydraulic control on the floor below the steering wheel. We recomm end using this for the purpose of c rabbing the machine for easy positioning of the rear platforms. An indicator is sited above the rear right hand wheel.
f) Do not enter or exit the Trel-Pick while it is moving.
g) Fuel - use unleaded petrol only.
h) Ensure that the Trel-Pick platform gates are c losed at all times.
i) Do not park the Trel-Pick on steep slopes.
j) Both raised platforms slide in & out. Tighten with bolt after positioning.
k) Both raised platforms can be raised & lowered by (1) loosening the tightening bolt (2)lift platform with 2 workers (3) re-pin height stop pins to required height (4) retighten tightening bolts (Caution keep feet c lear of bottom step)
l) When loading or unloading bins: (1) ensure that it is done on flat smooth ground conditions (2) Unlatch the appropriate handrail sides & swing down to allow fork-lift access (3) Ensure that all other platform workers are kept a safe distance away during this operation ( 4) When loading/unloading has been completed, swing the gate up again and hold up with both latches.
Trel-Pick Operator Safety InstructionsThese Safety Instructions are to be conveyed to anyone who will operate this TREL-PICK.
Only allow a competent trained operator to use the Trel-Pick.tpoi
sticker TrelPick operator instructions - DSTPOSI
THROTTLEOnly operate in
Engine Fast Speed when safe to do so.
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 52
Power Wire Winder Lower half wire jenny spool – ZWWLHWJS*
Con link 1”BS(16BCL) – CTCL01 Con link 1¼” BS(20BCL) – CTCL1-1/4 Half link 1”BS(16BHL) – CTHL01 Half link 1¼” BS(20BHL) – CTHL1-1/4
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 54
ROCK DIGGER
Special cast iron split sprocket 22T – WBSS22T Special cast iron split hub for 22T sprkt – WBSSH Special cast iron split sprocket 22T with hub & bolts – WBSS
Drive sprocket 22Tx40pitch, 20mm pl, 2 B with s/rings – WBMD22T40P2BIRN
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 55
ROCK DIGGER
Shear bolt yoke Series 4 – BCAK421000
Spline clamp yoke 1-3/8 Series 6 – BCA622538
Tube Yoke Inner – BCA6245
Unicross Series 4 – BCA421 Unicross Series 6 – BCA622
PTO shaft 1m 1-3/8 QR ends S4 - BCAB4105 PTO shaft 1.5m 6Spl QR ends S4- BCAB4150 PTO Shaft 1.5m no yoke Series S4 - BCEB4150 PTO Inner triangular tube 3m S4 – BCA364X3 PTO Outer triangular tube S4 – BCA433 Yoke tube inner Series 6 – BCA6245 Spline Shaft 1-3/8X6spline x 3m - BCB7283 Splined shaft cut ground,keyed 0.45m long – ZRDHDSS* Splined sleeve 1-3/8x6 – BCB7287
Roll pin 5/16x3 – RP5/16X3 Roll pin 1/2x3 – RP1/2X3
sticker MADE BY CRENDON 238x79 – DSCRENMACMADEBY
sticker SAFETY Read Owners Manual – DSSAFETYMAN
DANGER
Keep clear of all moving parts as they may cause
serious injury.dcc
sticker Keep clear of all moving parts – DSDANGER
Crendon Machinery Parts All Machinery (Not Squirrel) 8 – July - 2022
All Prices are + GST and is subject to can change wit out notice www.crendon.com.au [email protected] Ph 1300 761 922 P a g e 56
RAMMER Wire Rope Std RAMMER 6m x 8mm – ZRWR6 Wire Rope for extension 7.5m x 8mm – ZRWR8 Rubber mount M174 – RBM174-60 Not Available V belt B38 – VBB38 Not Available Pulley CI 6"x2B Ø1"; ¼key 2grubs – PCI6X2B1B Not Available Pulley CI 8"x2B Ø1"; ¼key 2grubs – PCI8X2B1B Not Available Wire rope sheave 100mm x 52mm x 17mm – PWRS100X52X17 Not Available Wire rope sheave 6"x52mm x 25mm wide – PWR6X52X20 Not Available Post latch – ZRPOSTLATCH Not Available Post latch spring – ZRHPLS* Motor spring – ZRHPMS*
RAMMER Hydraulic Motors Parts - White RS series
Seal Kit WHITE RS (Short) picture left – MWRSSKS Seal Kit WHITE RS (Full) picture right – MWRSSKF