M7xS_ESM

Preface

Notebook Computer M740S/M741S/M745S/M760S/M765S/M766S/M767S Service ManualPreface

I

Preface

NoticeThe company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. Version 1.0 May 2008

Preface

TrademarksIntel, Celeron and Intel Core are trademarks of Advanced Micro Devices, Inc. Windows is a registered trademark of Microsoft Corporation. Other brand and product names are trademarks and./or registered trademarks of their respective companies.

II

Preface

About this ManualThis manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the M740S/ M741S/M745S/M760S/M765S/M766S/M767S series notebook PC. The following information is included: Chapter 1, Introduction, provides general information about the location of system elements and their specifications. Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems and how to upgrade elements of the system. Appendix A, Part Lists Appendix B, Schematic Diagrams

Preface

III

Preface

IMPORTANT SAFETY INSTRUCTIONSFollow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to persons when using any electrical equipment:1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. 5. This product is intended to be supplied by a Listed Power Unit (DC Output 19V, 3.42A or 18.5V, 3.5A (65W) minimum AC/DC Adapter).

Preface

CAUTIONAlways disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.

TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER, TELECOMMUNICATION LINE CORDThis Computers Optical Device is a Laser Class 1 Product

IV

Preface

Instructions for Care and OperationThe notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:1. Dont drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.Do not expose the computer to any shock or vibration. Do not place it on an unstable surface. Do not place anything heavy on the computer.

2.

Keep it dry, and dont overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.Do not expose it to excessive heat or direct sunlight. Do not leave it in a place where foreign matter or moisture may affect the system. Dont use or store the computer in a humid environment. Do not place the computer on any surface which will block the vents.

Preface

3.

Follow the proper working procedures for the computer. Shut the computer down properly and dont forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.Do not turn off the power until you properly shut down all programs. Do not turn off any peripheral devices when the computer is on. Do not disassemble the computer by yourself. Perform routine maintenance on your computer.

V

Preface4. 5. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Take care when using peripheral devices.Use only approved brands of peripherals. Unplug the power cord before attaching peripheral devices.

Preface

Power SafetyThe computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.

Only use a power adapter approved for use with this computer. Your AC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one. When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. Before cleaning the computer, make sure it is disconnected from any external power supplies.Do not plug in the power cord if you are wet. Do not use the power cord if it is broken. Do not place heavy objects on the power cord.

VI

Preface

Battery Precautions Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. Do not remove any batteries from the computer while it is powered on. Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. Recharge the batteries using the notebooks system. Incorrect recharging may make the battery explode. Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel. Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded. Keep the battery away from metal appliances. Affix tape to the battery contacts before disposing of the battery. Do not touch the battery contacts with your hands or metal objects.

Preface

Battery Disposal The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturers instructions.

VII

Preface

Related DocumentsYou may also need to consult the following manual for additional information: Users Manual on CD This describes the notebook PCs features and the procedures for operating the computer and its ROM-based setup program. It also describes the installation and operation of the utility programs provided with the notebook PC.

PrefaceVIII

Preface

ContentsIntroduction ..............................................1-1Overview .........................................................................................1-1 System Specifications ................................. 1-2 External Locator - Top View with LCD Panel Open ......................1-5 External Locator - Front & Right side Views .................................1-6 External Locator - Left Side & Rear View .....................................1-7 External Locator - Bottom View .....................................................1-8 Mainboard Overview - Top (Key Parts) .........................................1-9 Mainboard Overview - Bottom (Key Parts) ..................................1-10 Mainboard Overview - Top (Connectors) .....................................1-11 Mainboard Overview - Bottom (Connectors) ...............................1-12 Top without Fingerprint (M740S) ................................................. A-3 Top without Fingerprint (M741S/M745S) .................................... A-4 Bottom (M740S/M741S/M745S) .................................................. A-5 LCD (M740S/M741S/M745S) ...................................................... A-6 HDD (M740S/M741S/M745S) ..................................................... A-7 COMBO (M740S/M741S/M745S) ............................................... A-8 DVD-Dual Drive (M740S/M741S/M745S) .................................. A-9 Top without Fingerprint (M760S) ............................................... A-10 Top without Fingerprint (M765S) ............................................... A-11 Top without Fingerprint (M766S/M767S) .................................. A-12 Bottom (M760S/M765S/M766S/M767S) ................................... A-13 LCD (M760S) .............................................................................. A-14 LCD (M765S) .............................................................................. A-15 LCD (M766S/M767S) ................................................................. A-16 HDD (M760S/M765S/M766S/M767S) ....................................... A-17 COMBO (M760S/M765S/M766S/M767S) ................................. A-18 DVD-Dual Drive (M760S/M765S/M766S/M767S) ................... A-19

Disassembly ...............................................2-1

Preface

Overview .........................................................................................2-1 Maintenance Tools ..........................................................................2-2 Connections .....................................................................................2-2 Maintenance Precautions .................................................................2-3 Disassembly Steps ...........................................................................2-4 Removing the Battery ......................................................................2-5 Removing the Hard Disk Drive .......................................................2-6 Removing the Optical (CD/DVD) Device ......................................2-9 Removing the System Memory (RAM) ........................................2-11 Removing the Inverter Board ........................................................2-13 Removing and Installing the Processor .........................................2-14 Removing the Wireless LAN Module ...........................................2-17 Removing the Bluetooth Module ..................................................2-18 Removing the Keyboard ................................................................2-19 Removing the Modem ...................................................................2-20

Schematic Diagrams................................. B-1System Block Diagram ...................................................................B-2 Penryn (Socket-P) 1/2 .....................................................................B-3 Penryn (Socket-P) 2/2 .....................................................................B-4 SiSM672 Host, PCIE 1/5 ................................................................B-5 SiSM672 DRAM 2/5 ......................................................................B-6 SiSM672 MuTIOL VGA 3/5 ..........................................................B-7 SiSM672 PWR 4/5 .........................................................................B-8 SiSM672 GND 5/5 .........................................................................B-9 DDRII SO-DIMM - 1 ...................................................................B-10 DDRII SO-DIMM - 2 ...................................................................B-11 SiS307ELV ...................................................................................B-12 Panel, CRT ....................................................................................B-13 IX

Part Lists ..................................................A-1

Part List Illustration Location ........................................................ A-2

Preface Inverter, Bluetooth, Fan ............................................................... B-14 968 PCI, IDE, MuTIOL, SPI 1/4 ................................................. B-15 968 PCIE, LAN, GPIO 2/4 ........................................................... B-16 968 USB SATA 3/4 ...................................................................... B-17 968 PWR, GND 4/4 ..................................................................... B-18 Clock Generator & Clock Buffer ................................................. B-19 PHY Realtek 8201CL ................................................................... B-20 KBC ITE8512E ............................................................................ B-21 ENE MR510, Card Reader ........................................................... B-22 Audio Codec ALC662 .................................................................. B-23 Audio AMP .................................................................................. B-24 SATA HDD, PWR, LID .............................................................. B-25 Multi I/O, ODD, 3G, Click BD for M74 ...................................... B-26 New Card, Mini PCIE, USB ........................................................ B-27 LED, PC Beep, TP, FP ................................................................. B-28 System/Ext-VGA Power .............................................................. B-29 AC-IN, Charger ............................................................................ B-30 VCORE ........................................................................................ B-31 VDD3, VDD5) ............................................................................. B-32 1.05VS, 1.2V, 1.5V ...................................................................... B-33 1.8V, 0.9VS .................................................................................. B-34 Click BD, Finger BD for M76 ..................................................... B-35 Multi Function Board ................................................................... B-36 Audio Board ................................................................................. B-37 Finger Sensor Board ..................................................................... B-38 Power Switch Board for M74 ....................................................... B-39 External ODD Board for M76 ...................................................... B-40 Power Switch Board for M76 ....................................................... B-41

Preface

X

Introduction

Chapter 1: IntroductionOverviewThis manual covers the information you need to service or upgrade the M740S/M741S/M745S/M760S/M765S/M766S/ M767S series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the Users Manual. Information about drivers (e.g. VGA & audio) is also found in Users Manual. That manual is shipped with the computer. Operating systems (e.g. Windows XP, Windows Vista, etc.) have their own manuals as do application software (e.g. word processing and database programs). If you have questions about those programs, you should consult those manuals.

1.Introduction

The M740S/M741S/M745S/M760S/M765S/M766S/M767S series notebook is designed to be upgradeable. See Disassembly on page 2 - 1 for a detailed description of the upgrade procedures for each specific component. Please note the warning and safety information indicated by the symbol. The balance of this chapter reviews the computers technical specifications and features.

Overview 1 - 1

Introduction

System SpecificationsFeatureProcessor Intel Core2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P T8100/ T8300 Intel Core2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P T9300/ T9500 Intel Core2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P T7100/ T7250

Specification45nm (45 Nanometer) Process Technology 3MB On-die L2 Cache & 800MHz FSB 2.1/ 2.4 GHz 45nm (45 Nanometer) Process Technology 6MB On-die L2 Cache & 800MHz FSB 2.5/ 2.6 GHz 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 800MHz FSB 1.80/ 2.0 GHz 65nm (65 Nanometer) Process Technology 4MB On-die L2 Cache & 800MHz FSB 2.0/ 2.2/ 2.4/ 2.6 GHz 65nm (65 Nanometer) Process Technology 1MB On-die L2 Cache & 533MHz FSB 1.73/ 1.86/ 2.0/ 2.13 GHz

1.Introduction

Intel Core2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P T7300/ T7500/ T7700/ T7800 Intel Celeron M Processor (478-pin) Micro-FCPGA Package, Socket P 530/ 540/ 550/ 560 Core Logic LCD SiS M672 + SiS968 Chipset M740S/M741S/M745S 14.1" WXGA/ WXGA+ Glare Type TFT LCD Video Adapter

M760S/M765S/M766S/M767S 15.4" WXGA/ WXGA+/ WSXGA+ Glare Type TFT LCD

SIS M672 Integrated Video High Preference 3D/2D Graphic Accelerator Shared Memory Architecture (up to 256MB dynamically allocated from system memory where needed) Supports DirectX 9.0 Supports Vertex Shader 2.0 and Pixel Shader 2.0 64-bit Wide DDRII (DDR2) Data Channel Two 200 Pin SO-DIMM Sockets Supporting DDRII (DDR2) 667MHz Memory Expandable up to 2GB (1024MB/ 2048MB DDRII Modules)

Memory

Security BIOS

Security (Kensington Type) Lock Slot One 8Mb SPI Flash ROM

BIOS Password Phoenix BIOS

1 - 2 System Specifications

IntroductionFeatureStorage Audio

SpecificationOne Changeable 12.7mm(h) PATA Optical Device (CD/DVD) Type Drive (see Optional on page 1 - 4) Easy Changeable 2.5" 9.5 mm (h) SATA (Serial) HDD High Definition Audio (HDA) Compliant with Microsoft UAA (Universal Audio Architecture) Winkey Keyboard Three USB 2.0 Ports One Headphone-Out Jack One Microphone-In Jack One S/PDIF-Out Jack Direct Sound 3D Compatible 2 * Built-In Speakers Built-In Microphone Built-In TouchPad with Scrolling Function One RJ-11 Modem Jack One RJ-45 LAN Jack One DC-In Jack One External Monitor Port

Keyboard & Pointing Device Interface

1.Introduction

Card Reader ExpressCard Slot Communication

Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards require a PC adapter One ExpressCard/34(54) Slot 10M/100Mb Base-T Ethernet LAN 56K MDC Modem V.90 & V.92 Compliant 3rd Party 802.11b/g Wireless LAN Mini-Card Module with USB interface (Option) Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) 1.3M (UVC or non UVC) or 2.0M Pixel USB PC Camera Module (Factory Option) 3.5G Module: UMTS/HSPDA-based 3.5G Module with Mini-Card Interface (Factory Option) Quad-band GSM/GPRS (850 MHz, 900 MHz, 1800 MHz, 1900 MHz) UMTS WCDMA FDD (2100 MHz) Supports ACPI 3.0 Supports Wake on LAN Supports Wake on USB Supports Resume from Modem Ring

UMTS ModesNote that UMTS modes CAN NOT be used in North America.

Power Management Power Battery

Full Range AC/DC Adapter AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 3.42A OR 18.5V, 3.5A (65 Watts) 6 Cell Smart Lithium-Ion Battery Pack, 4000mAH OR 4400mAH 9 Cell Smart Lithium-Ion Battery Pack, 7200mAH (Option)

System Specifications 1 - 3

IntroductionFeatureEnvironmental Spec Dimensions & Weight Temperature Operating: 5C - 35C Non-Operating: -20C - 60C M740S/M741S/M745S 336mm (w) * 250mm (d) * 24.8-35.7mm (h) 2.2 kg With 6 Cell Battery & ODD Optional Optical Drive Module Options: DVD-ROM/CD-RW Combo Drive Module DVD Dual (Super Multi) Drive Module 3rd Party 802.11b/g Wireless LAN Mini-Card Module with USB interface 9 Cell Smart Lithium-Ion Battery Pack 1.3M (UVC or non UVC) or 2.0M Pixel USB PC Camera Module (Factory Option)

SpecificationRelative Humidity Operating: 20% - 80% Non-Operating: 10% - 90% M760S/M765S/M766S/M767S: 359mm (w) * 268mm (d) * 24.8-37mm (h) 2.5 kg With 6 Cell Battery & ODD Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) UMTS/HSPDA-based 3.5G Module with Mini-Card Interface (Factory Option) Quad-band GSM/GPRS (850 MHz, 900 MHz, 1800 MHz, 1900 MHz) UMTS WCDMA FDD (2100 MHz)

1.Introduction

UMTS ModesNote that UMTS modes CAN NOT be used in North America.

1 - 4 System Specifications

Introduction

External Locator - Top View with LCD Panel Open1 1

Figure 1Top View 1. Optional Built-In PC Camera 2. LCD 3. Speakers 4. Power Button 5. Hot Key Buttons 6. Keyboard 7. Built-In Microphone 8. Touchpad & Buttons 9. LED Indicators

2

2

3 5 6 7

3 4 5

3

3 4 6 7

1.Introduction

8 9M740S/M741S/M745S

8 9M760S/M765S/M766S/M767S

10

10

External Locator - Top View with LCD Panel Open 1 - 5

Introduction Figure 2Front Views 1. LED Power & Communication Indicators 1

External Locator - Front & Right side Views

1.Introduction

Figure 3Right Side Views 1. S/PDIF-Out Jack 2. Microphone-In Jack 3. Headphone-Out Jack 4. USB 2.0 Port 5. Optical Device Drive Bay 6. RJ-11 Phone Jack 7. Security Lock Slot

1

2 3

4

5

6

7

1 - 6 External Locator - Front & Right side Views

Introduction

External Locator - Left Side & Rear View

Figure 4Left Side View 1. DC-In Jack 2. External Monitor Port 3. RJ-45 LAN Jack 4. Vent/Fan Intake/ Outlet 5. 2 * USB 2.0 Ports 6. ExpressCard Slot 7. 7-in-1 Card Reader

1

2

3

4

5

5

6 7

1.Introduction

Figure 5Rear View 1 1. Battery

External Locator - Left Side & Rear View 1 - 7

Introduction

External Locator - Bottom ViewFigure 6Bottom View 1. Battery 2. Bluetooth Module Cover 3. RAM & CPU Bay Cover 4. Vent/Fan Intake/ Outlet 5. Hard Disk Bay Cover 6. 3.5G USIM Card Location 5 1 2 2 4 4 3 3 1

1.Introduction

6 4

5

6 4

M740S/M741S/M745S

M760S/M765S/M766S/M767S

Overheating To prevent your computer from overheating make sure nothing blocks the vent/fan intakes while the computer is in use.

1 - 8 External Locator - Bottom View

Introduction

Mainboard Overview - Top (Key Parts)

Figure 7Mainboard Top Key Parts 1. Transformer 2. RTL8201CL 3. ExpressCard Connector 4. ENE MR510 5. KBC ITE IT8512E

1.Introduction

1

2

3 5 4

Mainboard Overview - Top (Key Parts) 1 - 9

Introduction Figure 8Mainboard Bottom Key Parts 1. CPU Socket (no CPU installed) 2. SiSM672 3. Memory Slots DDR2 SO-DIMM 4. ICS 9LPR600CGLF 5. Card Reader Socket 6. SiS307ELV 7. Audio Codec ALC62 8. Mini-Card Connector (WLAN Module) 9. Mini-Card Connector (3G Module) 10. SiS968

Mainboard Overview - Bottom (Key Parts)

8 6 9 2

1

1.Introduction

3 4 10 7 5

1 - 10 Mainboard Overview - Bottom (Key Parts)

Introduction

Mainboard Overview - Top (Connectors)

Figure 9Mainboard Top Connectors

3 2

4 1 1 6

1. USB Port 2. Inverter Connector 3. LCD Cable Connector 4. Keyboard Cable Connector 5. Audio Board Connector 6. Microphone Cable Connector 7. TouchPad Cable Connector

1.Introduction

7

5

Mainboard Overview - Top (Connectors) 1 - 11

Introduction Figure 10Mainboard Bottom Connectors 1. BT Cable Connector 2. Multi Board Connector 3. CD-ROM Connector 4. HDD Connector 5. CMOS Bat. Connector 6. CPU Fan Cable Connector 7. DC-In Jack 7

Mainboard Overview - Bottom (Connectors)

1 2

1.Introduction

3

6 4 5

1 - 12 Mainboard Overview - Bottom (Connectors)

Disassembly

Chapter 2: DisassemblyOverviewThis chapter provides step-by-step instructions for disassembling the M740S/M741S/M745S/M760S/M765S/M766S/ M767S series notebooks parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart. Procedures such as upgrading/replacing the RAM, optical device and hard disk are included in the Users Manual but are repeated here for your convenience. To make the disassembly process easier each section may have a box in the page margin. Information contained under the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the disassembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previous disassembly procedure. The amount of screws you should be left with will be listed here also. A box with a will also provide any possible helpful information. A box with a contains warnings.

2.Disassembly

Information

An example of these types of boxes are shown in the sidebar.Warning

Overview 2 - 1

Disassembly NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the battery is removed too).

Maintenance ToolsThe following tools are recommended when working on the notebook PC: M3 Philips-head screwdriver M2.5 Philips-head screwdriver (magnetized) M2 Philips-head screwdriver Small flat-head screwdriver Pair of needle-nose pliers Anti-static wrist-strap

2.Disassembly

ConnectionsConnections within the computer are one of four types:Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to gently pry the locking collar away from its base. When replacing the connection, make sure the connector is oriented in the same way. The pin1 side is usually not indicated. To release this connector type, grasp it at its head and gently rock it from side to side as you pull it out. Do not pull on the wires themselves. When replacing the connection, do not try to force it. The socket only fits one way. To release these connectors, use a small pair of needle-nose pliers to gently lift the connector away from its socket. When replacing the connection, make sure the connector is oriented in the same way. The pin1 side is usually not indicated. To separate the boards, gently rock them from side to side as you pull them apart. If the connection is very tight, use a small flat-head screwdriver - use just enough force to start.

Pressure sockets for multi-wire connectors

Pressure sockets for ribbon connectors

Board-to-board or multi-pin sockets

2 - 2 Overview

Disassembly

Maintenance PrecautionsThe following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions:1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other components could be damaged. 2. Don't overheat it. Note the proximity of any heating elements. Keep the computer out of direct sunlight. 3. Avoid interference. Note the proximity of any high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage components and/or data. You should also monitor the position of magnetized tools (i.e. screwdrivers). 4. Keep it dry. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. 5. Be careful with power. Avoid accidental shocks, discharges or explosions. Before removing or servicing any part from the computer, turn the computer off and detach any power supplies. When you want to unplug the power cord or any cable/wire, be sure to disconnect it by the plug head. Do not pull on the wire. 6. Peripherals Turn off and detach any peripherals. 7. Beware of static discharge. ICs, such as the CPU and main support chips, are vulnerable to static electricity. Before handling any part in the computer, discharge any static electricity inside the computer. When handling a printed circuit board, do not use gloves or other materials which allow static electricity buildup. We suggest that you use an anti-static wrist strap instead. 8. Beware of corrosion. As you perform your job, avoid touching any connector leads. Even the cleanest hands produce oils which can attract corrosive elements. 9. Keep your work environment clean. Tobacco smoke, dust or other air-born particulate matter is often attracted to charged surfaces, reducing performance. 10. Keep track of the components. When removing or replacing any part, be careful not to leave small parts, such as screws, loose inside the computer.Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.

2.Disassembly

CleaningDo not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Overview 2 - 3

Disassembly

Disassembly StepsThe following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED.

To remove the Battery:1. Remove the battery page 2 - 5

To remove the Wireless LAN Module:1. Remove the battery 2. Remove the wireless LAN page 2 - 5 page 2 - 17

To remove the HDD:1. Remove the battery 2. Remove the HDD page 2 - 5 page 2 - 6

To remove the Bluetooth Modules:1. Remove the battery 2. Remove the Bluetooth page 2 - 5 page 2 - 18

2.Disassembly

To remove the Optical Device:1. Remove the battery 2. Remove the Optical device page 2 - 5 page 2 - 9

To remove the Keyboard:1. Remove the battery 2. Remove the keyboard page 2 - 5 page 2 - 19

To remove the System Memory:1. Remove the battery 2. Remove the system memory page 2 - 5 page 2 - 11

To remove the Modem:1. 2. 3. 4. 5. 6. 7. Remove the battery Remove the HDD Remove the system memory Remove the Optical device Remove the processor Remove the keyboard Remove the modem page 2 - 5 page 2 - 6 page 2 - 11 page 2 - 9 page 2 - 14 page 2 - 19 page 2 - 20

To remove the Inverter Board:1. Remove the battery 2. Remove the inverter board page 2 - 5 page 2 - 13

To remove and install a Processor:1. Remove the battery 2. Remove the processor 3. Install the processor page 2 - 5 page 2 - 14 page 2 - 16

2 - 4 Disassembly Steps

Disassembly

Removing the Battery1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. 3 Slide the battery 6 in the direction of the arrow 4 . a.

Figure 1Battery Removala. Slide the latch and hold in place. b. Slide the battery in the direction of the arrow.

2

1

2.Disassembly

b.

3

4

3. Battery

Removing the Battery 2 - 5

Disassembly

Removing the Hard Disk DriveFigure 2HDD Assembly Removala. Locate the HDD bay cover and remove the screw(s).

The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h). Follow your operating systems installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the Users Manual) when setting up a new hard disk.

Hard Disk Upgrade Process1. Turn off the computer, and remove the battery (page 2 - 5). 2. Locate the hard disk bay cover and remove screw 1 & 2 . a.

2.Disassembly

1

2 M740S/M741S/M745S

1

2

M760S/M765S/M766S/M767S

HDD System Warning New HDDs are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD.

2 Screws

You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.

2 - 6 Removing the Hard Disk Drive

Disassembly For M740S/M741S/M745S computers:3. 4. 5. 6. 7.3 Remove the hard disk bay cover 6 . Grip the tab and slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . 7 8 Remove the screw 6 and the adhesive cover 6 from the hard disk 6 . Reverse the process to install a new hard disk (do not forget to replace all the screws and covers).

Figure 3HDD Assembly Removal (contd.)b. Remove the HDD bay cover. c. Grip the tab and slide the HDD in the direction of the arrow. d. Lift the HDD assembly out of the bay. e. Remove the screw and adhesive cover.

b. 3 e. 6 7

2.Disassembly

c.

4

8

d. 53. HDD Bay Cover 7. Adhesive Cover 8. HDD

1 Screw

Removing the Hard Disk Drive 2 - 7

Disassembly Figure 4HDD Assembly Removal (contd.)f. Remove the HDD Bay Cover. g. Grip the tab and slide the HDD in the direction of the arrow. h. Lift the HDD assembly out of the bay. i. Remove the screw and adhesive cover.

For M760S/M765S/M766S/M767S computers:8. 9. 10. 11. 12.3 Remove the hard disk bay Cover 6 . Grip the tab and slide the hard disk in the direction of arrow 4 . Lift the hard disk out of the bay 5 . 8 9 Remove the screws 6 & 7 and the adhesive cover 6 from the hard disk 6 . Reverse the process to install a new hard disk (do not forget to replace all the screws and covers).

f.

3 i. 6 g. 4 8 7 9

2.Disassembly

h.3. HDD Bay Cover 8. Adhesive Covere 9. HDD

5

2 Screws

2 - 8 Removing the Hard Disk Drive

Disassembly

Removing the Optical (CD/DVD) Device1. Turn off the computer, and remove the battery (page 2 - 5). 2. M740S/M741S/M745S: (see over for M760S/M765S/M766S/M767S) Locate the component bay cover 1 and remove screws 2 - 4 . 3. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. 4. Carefully disconnect the fan cable 5 , and remove the cover 1 . 5. Remove the screw at point 6 , and use a screwdriver to carefully push out the optical device 8 at point 7 . 6. Insert the new device and carefully slide it into the computer (the device only fits one way. DO NOT FORCE IT; The screw holes should line up). 7. Restart the computer to allow it to automatically detect the new device. a. 2 3 1 6 M740S/M741S/M745S b. 1 d. 4 c.

Figure 5Optical Device Removala. Remove the screws. b. Disconnect the fan cable and remove the cover. c. Remove the screw. d. Push the optical device out off the computer at point 7.

2.Disassembly

c.

1. Component Bay Cover 8. Optical Device

5

8

7

4 Screws

Removing the Optical (CD/DVD) Device 2 - 9

Disassembly Figure 6Optical Device Removal (contd.)e. Remove the screws. f. Remove the cover. g. Remove the screw. h. Push the optical device out off the computer at point 7.

8. 9. 10. 11.

M760S/M765S/M766S/M767S: Locate the hard disk bay cover 1 and loosen screws 2 & 3 . Remove the hard disk bay cover 1 . Remove the screw at point 6 , and use a screwdriver to carefully push out the optical device 8 at point 7 . Insert the new device and carefully slide it into the computer (the device only fits one way. DO NOT FORCE IT; The screw holes should line up). 12. Restart the computer to allow it to automatically detect the new device. e. g.

2.Disassembly

6 1 2 3 7

M760S/M765S/M766S/M767S f. h.

11. HDD Bay Cover 8. Optical Device

8 7

3 Screws

2 - 10 Removing the Optical (CD/DVD) Device

Disassembly

Removing the System Memory (RAM)The computer has two memory sockets for 200 pin Small Outline Dual In-line Memory Modules (SO-DIMM) supporting DDR2 667MHz. The main memory can be expanded up to 2GB. The SO-DIMM modules supported are 1024MB, and 2048MB and DDRII Modules. The total memory size is automatically detected by the POST routine once you turn on your computer.

Figure 7RAM Module Removala. Remove the screws. b. Remove the cover.

Memory Upgrade Process1. 2. 3. 4. Turn off the computer, remove the battery (page 2 - 5). Locate the component bay cover 1 , and remove screws 2 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 1 . a. 2 3 1 4 3 2 1 4 M740S/M741S/M745S b. 1 M760S/M765S/M766S/M767S

Contact Warning Be careful not to touch the metal pins on the modules connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the modules performance.

2.Disassembly

Note: Only one model is pictured here, however the component locations are the same for both models.1. Component Bay Cover

5

3 Screws

Removing the System Memory (RAM) 2 - 11

Disassembly Figure 8RAM Module Removal (contd.)c. Pull the release latch(es). d. Remove the module(s). e. Properly re-insert the bay cover pins.

5. Gently pull the two release latches ( 6 & 7 ) on the sides of the memory socket in the direction indicated by the arrows (Figure 8c). c. d.

6

7

8

2.Disassembly

6. 7. 8. 9.

The RAM module(s) 8 will pop-up (Figure 8d), and you can then remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30 angle and fit the connectors firmly into the memory slot. The modules pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 11. Replace the bay cover and screws (make sure you reconnect the fan cable before screwing down the bay cover). Note for M760S/M765S/M766S/M767S computers that there are four 9 - 12 cover pins which need to be aligned with slots in the case, to insure a proper cover fit, before screwing down the bay cover 1 . e. 9 110 11

8. RAM Module(s)

12

12. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.

2 - 12 Removing the System Memory (RAM)

Disassembly

Removing the Inverter Board1. Turn off the computer, and remove the battery (page 2 - 5). 2. Remove any rubber covers, screws 1 - 6 (Figure 9a), then run your finger around the middle of the frame to carefully unsnap the LCD front panel module 7 from the back. 3. Discharge the remaining system power (see Inverter Power Warning below). 4. Remove screw 8 (Figure 9b) from the inverter, and carefully lift the inverter board up slightly. 5. Disconnect cables 9 & 10 (Figure 9c) from the inverter, then remove the inverter 11 (Figure 9d) from the top case assembly. a. 2 3 4 5 b.

Figure 9Inverter Board Removala. Remove the 6 screws and unsnap the LCD front panel module from the back. b. Remove the screw and discharge the remaining power from the inverter board and lift the board up slightly. c. Disconnect the cables from the inverter. d. Remove the inverter.

2.Disassembly

8

c. 1 7 69 10

d.Inverter Power Warning In order to prevent a short circuit when removing the inverter it is necessary to discharge any remaining system power. To do so, press the computers power button for a few seconds before disconnecting the inverter cable. 7. LCD Front Panel 11. Inverter Board

11 6 Screws

Removing the Inverter Board 2 - 13

Disassembly

Removing and Installing the ProcessorFigure 10Processor Removala. Remove the cover and Iocate the heat sink. b. Remove the screws in the order indicated. c. Remove the heat sink.

Processor Removal Procedure1. 2. 3. 4. Turn off the computer, remove the battery (page 2 - 5) and the component bay cover (page 2 - 11). The CPU heat sink will be visible at point 1 on the mainboard. Remove screws 2 - 4 (Figure 10b) from the heat sink in the order indicated. Carefully lift up the heat sink 5 (Figure 10c) off the computer.a.

1

Note: Only one model is pictured here, however the component locations are the same for both models.

2.Disassembly

b.

c.

2 4

3 5

5. Heat Sink

3 Screws

2 - 14 Removing and Installing the Processor

Disassembly5. 6. 7. 8. Turn the release latch 6 towards the unlock symbol , to release the CPU (Figure 11a). Carefully (it may be hot) lift the CPU 7 up out of the socket (Figure 11b). See page 2 - 16 for information on inserting a new CPU. When re-inserting the CPU, pay careful attention to the pin alignment, it will fit only one way (DO NOT FORCE IT!). d.

Figure 11Processor Removal (contd)d. Turn the release latch to unlock the CPU. e. Lift the CPU out of the socket.

6

6

2.Disassembly

Unlock e.

Lock

7

Caution The heat sink, and CPU area in general, contains parts which are subject to high temperatures. Allow the area time to cool before removing these parts. 7. CPU

Removing and Installing the Processor 2 - 15

Disassembly Figure 12Processor Installationa. Insert the CPU. b. Turn the release latch towards the lock symbol. c. Remove the sticker from the heat sink and insert the heat sink. d. Tighten the screws.

Processor Installation Procedure1. Insert the CPU 1 , pay careful attention to the pin alignment, it will fit only one way (DO NOT FORCE IT!), and turn the release latch 2 towards the lock symbol (Figure 12b). 2. Remove the sticker 3 (Figure 12c) from the heat sink. 3. Insert the heat sink 4 as indicated in Figure 12c. 4. Tighten screws 5 - 7 in the order indicated on the label. 5. Replace the component bay cover and tighten the screws (page 2 - 14). a. 1 3 4 c.

2.Disassembly

b.

d.5 6

41. CPU 4. Heat Sink

2

7

3 Screws

2 - 16 Removing and Installing the Processor

Disassembly

Removing the Wireless LAN Module1. 2. 3. 4. 5. Turn off the computer, remove the battery (page 2 - 5) and the component bay cover (page 2 - 11). The Wireless LAN module will be visible at point 1 on the mainboard. Carefully disconnect cables 2 - 3 , then remove screw 4 from the module socket. The Wireless LAN module 5 will pop-up. Lift the Wireless LAN module (Figure 13d) up and off the computer. a. 1 b. 2 3 4

Figure 13Wireless LAN Module Removala. Remove the cover. b. Disconnect the cable and remove the screw. c. The WLAN module will pop up. d. Lift the WLAN module out.

Note: Only one model is pictured here, however the component locations are the same for both models.

Note: Make sure you reconnect the antenna cable to 1 + 2 socket (Figure b).

2.Disassembly

c.

d.5. WLAN Module.

5

5

1 Screw

Removing the Wireless LAN Module 2 - 17

Disassembly Figure 14Bluetooth Module Removal

Removing the Bluetooth ModuleTurn off the computer, remove the battery (page 2 - 5). Locate the Bluetooth bay cover, and remove the screw 1 and cover 2 . Remove the screw 3 and turn the module over. Carefully separate the Bluetooth module from the connector 4 and disconnect the cable 5 . Lift the Bluetooth module 6 (Figure 14c) up and off the computer. a. c.

1. 2. 3. a. Remove the screw. 4. b. Lfit the cover and remove 5. the screw.c. Disconnect the cable and the connector. d. Lift the Bluetooth module up off the socket.

5

2.Disassembly

1

4

b. 2

d. 6

2. Cover 6. Bluetooth Module

3

2 Screws

2 - 18 Removing the Bluetooth Module

Disassembly

Removing the Keyboard1. Turn off the computer, and remove the battery (page 2 - 5). 2. Press the four keyboard latches at the top of the keyboard to elevate the keyboard from its normal position (you may need to use a small screwdriver to do this). 3. Carefully lift the keyboard 5 up, being careful not to bend the keyboard ribbon cable (Figure 15b). 4. Disconnect the keyboard ribbon cable 6 from the locking collar socket 7 . a. 1 2 3 4 c.

Figure 15Keyboard Removala. Press the four latches to release the keyboard. b. Lift the keyboard up and disconnect the cable from the locking collar. c. Remove the keyboard.

2.Disassembly

b. 6 5 7 5

Re-Inserting the Keyboard When re-inserting the keyboard firstly align the four keyboard tabs at the bottom of the keyboard with the slots in the case.

5. Keyboard

Removing the Keyboard 2 - 19

Disassembly

Figure 16Modem Removala. Remove the screws and diconnect the cable. b. Turn the computer over, remove the screws and disconnect the cable. c. Remove the screws.

Removing the Modem1. Turn off the computer, remove the battery (page 2 - 5), HDD (page 2 - 6), component bay cover (page 2 - 11), optical device (page 2 - 9), CPU (page 2 - 14), bluetooth (page 2 - 18) and keyboard (page 2 - 19). 2. Remove screws 1 - 18 from the bottom case and carefully disconnect the cable 21 from the mainboard (Figure 17a). 3. Turn the computer over, remove screws 22 - 23 and disconnect cables 24 - 26 (Figure 17b). 4. For M760S/M765S/M766S/M767S only - remove screws 27 - 28 (Figure 17c) from the rear of the computer. M740S/M741S/M745S a. 1 2 321

M760S/M765S/M766S/M767S 9 1011

2.Disassembly

5 4 6

7

8

1 2

321

4 520

7 6

8

9 10

11

12 13

18

16 15

12 13

18

19 16 15

17

14

17

14

b.26 22 24 25 23 22 24 25 26 23

20 Screws (M740S/M741S/ M745S)/ 24 Screws (M760S/ M765S/M766S/ M767S)

c.27 28

2 - 20 Removing the Modem

Disassembly5. 6. 7. 8. 9. Carefully lift the top case 27 up and off the computer (Figure 17d). Remove screws 28 - 30 (Figure 17e) from the computer. Remove screws 31 - 32 (Figure 17f) from the modem module. Lift the modem up and separate the modem from the connector 33 . Lift the modem 34 off the computer. d. 27 M740S/M741S/M745S29 30

Figure 17Modem Removal (contd.)d. Lift the cover off the computer. e. Remove the screws. f. Remove the screws and disconnect the connector. g. Lift the modem out.

M740S/M741S/M745S e.28

M760S/M765S/M766S/M767S

28

2.Disassembly

29 30

f.31 31 33 32

27 M760S/M765S/M766S/M767S g.

33 32

27. Top Case 34. Modem

34

34

5 Screws (M740S/ M741S/M745S/ M760S/M765S/ M766S/M767S)

Removing the Modem 2 - 21

Disassembly

2.Disassembly2 - 22

Part Lists

Appendix A: Part ListsThis appendix breaks down the M740S/M741S/M745S/M760S/M765S/M766S/M767S series notebooks construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturers part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation. Note: Some assemblies may have parts in common (especially screws). However, the part lists DO NOT indicate the total number of duplicated parts used. Note: Be sure to check any update notices. The parts shown in these illustrations are appropriate for the system at the time of publication. Over the product life, some parts may be improved or re-configured, resulting in new part numbers.

A.Part Lists

A - 1

Part Lists

Part List Illustration LocationThe following table indicates where to find the appropriate part list illustration. Table A- 1Part List Illustration LocationParts Top without Fingerprint Bottom M740S page A - 3 M741S/M745S page A - 4 M760S page A - 10 M765S page A - 11 page A - 13 page A - 14 page A - 14 page A - 17 page A - 18 page A - 19 page A - 14 M766S/M767S page A - 12

page A - 5 page A - 6 page A - 7 page A - 8 page A - 9

A.Part Lists

LCD HDD COMBO DVD-Dual Drive

A - 2 Part List Illustration Location

Part Lists

Top without Fingerprint (M740S)

Figure A - 1Top without Fingerprint (M740S)

A.Part Lists

()

Top without Fingerprint (M740S) A - 3

Part Lists

Top without Fingerprint (M741S/M745S)

Figure A - 2

A.Part Lists

Top without Fingerprint (M741S/M745S)

()

A - 4 Top without Fingerprint (M741S/M745S)

Part Lists

Bottom (M740S/M741S/M745S)

Figure A - 3Bottom (M740S/M741S/ M745S)

A.Part Lists

3

Bottom (M740S/M741S/M745S) A - 5

Part Lists

LCD (M740S/M741S/M745S)

Figure A - 4

A.Part Lists

LCD (M740S/M741S/ M745S)

()()

A - 6 LCD (M740S/M741S/M745S)

Part Lists

HDD (M740S/M741S/M745S)

Figure A - 5HDD (M740S/M741S/ M745S)

A.Part Lists

()

HDD (M740S/M741S/M745S) A - 7

Part Lists

COMBO (M740S/M741S/M745S)

Figure A - 6

A.Part Lists

COMBO (M740S/M741S/ M745S)

*()

A - 8 COMBO (M740S/M741S/M745S)

Part Lists

DVD-Dual Drive (M740S/M741S/M745S)

Figure A - 7*()

DVD-Dual Drive (M740S/M741S/ M745S)

A.Part Lists

DVD-Dual Drive (M740S/M741S/M745S) A - 9

Part Lists

Top without Fingerprint (M760S)

Figure A - 8

A.Part Lists

Top without Fingerprint (M760S)

()

()

A - 10 Top without Fingerprint (M760S)

Part Lists

Top without Fingerprint (M765S)

Figure A - 9Top without Fingerprint (M765S)

A.Part Lists

()

Top without Fingerprint (M765S) A - 11

Part Lists

Top without Fingerprint (M766S/M767S)

Figure A - 10

A.Part Lists

Top without Fingerprint (M766S/M767S)

()

A - 12 Top without Fingerprint (M766S/M767S)

Part Lists

Bottom (M760S/M765S/M766S/M767S)

Figure A - 11Bottom (M760S/M765S/ M766S/M767S)

A.Part Lists

()()

() )3

() () ,

Bottom (M760S/M765S/M766S/M767S) A - 13

Part Lists

LCD (M760S)

Figure A - 12

A.Part Lists

LCD (M760S)()

()

A - 14 LCD (M760S)

Part Lists

LCD (M765S)

Figure A - 13LCD (M765S)

A.Part Lists

()

LCD (M765S) A - 15

Part Lists

LCD (M766S/M767S)

Figure A - 14

A.Part Lists

LCD (M766S/M767S)

()

()

A - 16 LCD (M766S/M767S)

Part Lists

HDD (M760S/M765S/M766S/M767S)

Figure A - 15HDD (M760S/M765S/ M766S/M767S)

A.Part Lists

()

HDD (M760S/M765S/M766S/M767S) A - 17

Part Lists

COMBO (M760S/M765S/M766S/M767S)

Figure A - 16

A.Part Lists

COMBO (M760S/M765S/ M766S/M767S)*()

A - 18 COMBO (M760S/M765S/M766S/M767S)

Part Lists

DVD-Dual Drive (M760S/M765S/M766S/M767S)

Figure A - 17DVD-Dual Drive (M760S/M765S/ M766S/M767S)*()

A.Part Lists

DVD-Dual Drive (M760S/M765S/M766S/M767S) A - 19

Part Lists

A.Part ListsA - 20

Schematic Diagrams

Appendix B: Schematic DiagramsThis appendix has circuit diagrams of the M740S/M741S/M745S/M760S/M765S/M766S/M767S notebooks PCBs. The following table indicates where to find the appropriate schematic diagram.Diagram - PageSystem Block Diagram - Page B - 2 Penryn (Socket-P) 1/2 - Page B - 3 Penryn (Socket-P) 2/2 - Page B - 4 SiSM672 Host, PCIE 1/5 - Page B - 5 SiSM672 DRAM 2/5 - Page B - 6 SiSM672 MuTIOL VGA 3/5 - Page B - 7 SiSM672 PWR 4/5 - Page B - 8 SiSM672 GND 5/5 - Page B - 9 DDRII SO-DIMM - 1 - Page B - 10 DDRII SO-DIMM - 2 - Page B - 11 SiS307ELV - Page B - 12 Panel, CRT - Page B - 13 Inverter, Bluetooth, Fan - Page B - 14 968 PCI, IDE, MuTIOL, SPI 1/4 - Page B - 15

Diagram - Page968 PCIE, LAN, GPIO 2/4 - Page B - 16 968 USB SATA 3/4 - Page B - 17 968 PWR, GND 4/4 - Page B - 18 Clock Generator & Clock Buffer - Page B - 19 PHY Realtek 8201CL - Page B - 20 KBC ITE8512E - Page B - 21 ENE MR510, Card Reader - Page B - 22 Audio Codec ALC662 - Page B - 23 Audio AMP - Page B - 24 SATA HDD, PWR, LID - Page B - 25 Multi I/O, ODD, 3G, Click BD for M74 - Page B - 26 New Card, Mini PCIE, USB - Page B - 27 LED, PC Beep, TP, FP - Page B - 28 System/Ext-VGA Power - Page B - 29

Diagram - PageAC-IN, Charger - Page B - 30 VCORE - Page B - 31 VDD3, VDD5) - Page B - 32 1.05VS, 1.2V, 1.5V - Page B - 33 1.8V, 0.9VS - Page B - 34 Click BD, Finger BD for M76 - Page B - 35 Multi Function Board - Page B - 36 Audio Board - Page B - 37 Power Switch Board for M74 - Page B - 38 External ODD Board for M76 - Page B - 39 Power Switch Board for M76 - Page B - 40

Table B - 1Schematic Diagrams

B.Schematic Diagrams

Version Note The schematic diagrams in this chapter are based upon version 6-7P-M74S9003A. If your mainboard (or other boards) are a later version, please check with the Service Center for updated diagrams (if required).

B - 1

Schematic Diagrams

System Block DiagramCLEVO M740S System Block Diagram14. 318 MHz

A C- IN ,CH AR GE R

SY STE M PO WE R, GPU C OR E

M UL TI I/ O BO AR DS PK _R, R J- 11 M OD EM, C CD

+V COR E

C ol ck Ge ne rat or I CS 9LP R6 0056p ins TSSO P 1 7.1 *8.1 *1 .2 mm

I nt el P en ryn P ROC ES SO R479 pin s socket P3 5*35 *2 .7 mm

Memory Termination VD D3, VD D5 ,3 .3 V,5 V D DR II S O- DI MM 0 1. 05V S, 1. 5V ,1 .2V D DR II S O- DI MM 1

M7 6S U

B.Schematic Diagrams

A ud io Bo ar dU SB , S PD IF , M IC I N H EA DPH ON E

EX TE RNA L VGA N V 940 0M -GS 53 3 bal ls BG A 2 3* 23* 2. 5mm

Sheet 1 of 48 System Block Diagram

LCD C ON NEC TO R, INV ER TE R

FS B 667/800 MHz

1. 8V, 0. 9V SClo ck B uff er ICS 9P 93 52 8pin S s SOP 17. 1*8. 1*1.2 mm

LV DS (T V) Si S30 7E LV169 ball BG s A 13*1 3*1.7 mm

NO RT H BR ID GE S iS M6 72852balls TEBGA3 5*35 *2 .4 mm

CL ICK BOAR D

TO UC H PAD Sy na pt ic81 0602 -170 3

533/667(/800) MHzRJ11

SPDI F OUT

MI C IN

HP OUT

CRT

32 .768 KHz

EC IT E 851 2E12 8pin LQ s FP 14 *1 4*1. 6mm

S PI

Mu TI OL 1 G LP C 33 MHz

A ZA LI A M DC M OD UL EM DC CO N

Az ali a Co dec Re al te k AL C6 624 8pin LQ s FP 9*9 *1 .6m m

AUD IO A MPANPA C APA2 056A 2 4pin TS s SOP 9.8 *6 .4 *1 .2 mm INT SPK

S OU TH B RI DGE Si S9 68INT . K/ B

A ZA LI A LI NK P CI B US P CI E G MA C

24 MHz 33 MHz 100 MHz

INT MIC

EC S MB USTH ERM AL SE NSO R F7 538 3M S MA RT F AN SM AR T BA TT ERY32.7 68KH z

570balls mBGA27 *2 7*2. 5mm

SA TA I/ II 3 .0 Gb /s PA TA -13 3

U SB 2. 0 480 MbpsFING ER PRIN TER BOAR D

10 /1 00 M P HY R TL 82 01C L 48 pi ns LQ FP9*9*1. 7mm 2 MH 5 z

N ew Ca rd SOC KE T (US B0 )

M in i P CI E S OCK ET ( USB 1)

CA RD RE AD ERE nE MR 510 128pin LQF P 14 *1 4*1. 4mm 24.5 76 MHz

S AT A H DD , L ID

OD D

CC D US B6

( US B7)

3 G CAR D Bl ue too th U SB4(Opt iona l)

USB & P hone Jac B' k d

(U SB 5)

(U SB 3)

USB 2 F in ger Pr in tRJ45

M IN I P CI E GO LAN

7 IN1 SO CKE T

12 MHz (O ptio nal)

B - 2 System Block Diagram

Schematic Diagrams

Penryn (Socket-P) 1/24 H _ A # [ 35 : 3 ] H_ A # 3 H_ A # 4 H_ A # 5 H_ A # 6 H_ A # 7 H_ A # 8 H_ A # 9 H_ A # 1 0 H_ A # 1 1 H_ A # 1 2 H_ A # 1 3 H_ A # 1 4 H_ A # 1 5 H_ A # 1 6 J4 L5 L4 K5 M3 N2 J1 N3 P5 P2 L2 P4 P1 R1 M1 K3 H2 K2 J3 L1 Y2 U5 R3 W6 U4 Y5 U1 R4 T5 T3 W2 W5 Y4 U2 V4 W3 AA4 AB2 AA3 V1 A6 A5 C4 D5 C6 B4 A3 Z 02 0 1 Z 02 0 2 Z 02 0 3 Z 02 0 4 Z 02 0 5 Z 02 0 6 Z 02 0 7 Z 02 0 8 Z 02 0 9 CP U_ B S E L 2 CP U_ B S E L 1 CP U_ B S E L 0 H _ P R O C H OT # M4 N5 T2 V3 B2 D2 D 22 D3 F6 JS K T 1 A A [3 ]# A [4 ]# A [5 ]# A [6 ]# A [7 ]# A [8 ]# A [9 ]# A [1 0 ]# A [1 1 ]# A [1 2 ]# A [1 3 ]# A [1 4 ]# A [1 5 ]# A [1 6 ]# A D S T B [ 0] # R R R R R E Q[ 0 ] # E Q[ 1 ] # E Q[ 2 ] # E Q[ 3 ] # E Q[ 4 ] # AD S# B NR # B P R I# DE F E R # DR DY # DB S Y # B R0 # H1 E2 G5 H5 F 21 E1 F1 D2 0 B3 H4 C1 F3 F4 G3 G2 G6 E4 A D4 A D3 A D1 A C4 A C2 A C1 A C5 AA6 AB3 AB5 AB6 C2 0 H_ B P M 0 # R H_ B P M 1 # R H_ B P M 2 # R H_ B P M 3 # R H_ P R DY # R H _ P R E Q# H_ T CK H_ T DI R H_ T DO H _ T MS H_ T RS T # H_ D B R# 1 00 1 01 66 92 88 H _ C P U R S T# H _ B R 0# H_ IE R R# H _ I N I T# J S K T 1B H_ A D S # 4 H_ B N R# 4 H_ B P R I# 4 H_ D E F E R# 4 H_ D RDY # 4 H_ D B S Y # 4 H _ B R 0# 4 H _ I N I T# 2 2 H _ L OC K # 4 H _ C P U R S T# 4 H _ R S #0 4 H _ R S #1 4 H _ R S #2 4 H_ T RD Y # 4 H _ H I T# 4 H _ H I TM # 4 51 _ 1 %_ 0 4 51 _ 1 %_ 0 4 51 _ 1 %_ 0 4 51 _ 1 %_ 0 4 56 _ 1 %_ 0 4 1 . 05 V S 4 H _D # [ 63 : 0 ] H_ D# 0 H_ D# 1 H_ D# 2 H_ D# 3 H_ D# 4 H_ D# 5 H_ D# 6 H_ D# 7 H_ D# 8 H_ D# 9 H_ D# 1 0 H_ D# 1 1 H_ D# 1 2 H_ D# 1 3 H _ D #1 4 H_ D# 1 5 E2 2 F24 E2 6 G2 2 F23 G2 5 E2 5 E2 3 K2 4 G2 4 J24 J23 H2 2 F26 K2 2 H2 3 J26 H2 6 H2 5 N2 2 K2 5 P2 6 R2 3 L23 M2 4 L22 M2 3 P2 5 P2 3 P2 2 T24 R2 4 L25 T25 N2 5 L26 M2 6 N2 4 A D2 6 C2 3 D2 5 C2 4 AF2 6 AF1 A2 6 C 3 B2 2 B2 3 C2 1 D[0 ]# D[1 ]# D[2 ]# D[3 ]# D[4 ]# D[5 ]# D[6 ]# D[7 ]# D[8 ]# D[9 ]# D[1 0 ]# D[1 1 ]# D[1 2 ]# D[1 3 ]# D[1 4 ]# D[1 5 ]# D S T B N [ 0] # DS T B P [0 ]# DIN V [0 ]# D [ 32 ] # D [ 33 ] # D [ 34 ] # D [ 35 ] # D [ 36 ] # D [ 37 ] # D [ 38 ] # D [ 39 ] # D [ 40 ] # D [ 41 ] # D [ 42 ] # D [ 43 ] # D [ 44 ] # D [ 45 ] # D [ 46 ] # D [ 47 ] # DS T B N[2 ]# DS T B P [2 ]# D INV [2 ]# Y 22 AB2 4 V2 4 V2 6 V2 3 T22 U 25 U 23 Y 25 W22 Y 23 W24 W25 AA2 3 AA2 4 AB2 5 Y 26 AA2 6 U 22 AE2 4 A D 24 AA2 1 AB2 2 AB2 1 A C 26 A D 20 AE2 2 AF2 3 A C 25 AE2 1 A D 21 A C 22 A D 23 AF2 2 A C 23 AE2 5 AF2 4 A C 20 R 26 U 26 AA1 Y 1 E5 B5 D 24 D 6 D 7 AE6 H_ D# 3 2 H_ D# 3 3 H_ D# 3 4 H_ D# 3 5 H_ D# 3 6 H_ D# 3 7 H_ D# 3 8 H_ D# 3 9 H_ D# 4 0 H_ D# 4 1 H_ D# 4 2 H_ D# 4 3 H_ D# 4 4 H_ D# 4 5 H_ D# 4 6 H_ D# 4 7 H _ D # [ 63 : 0 ] 4

CO NTROL

IE RR # IN IT # L OC K #

DA GRP 2 TA

AD DR G ROUP_0

DATA GR 0 P

4 H _ A D S TB # 0 4 H _ R E Q# [ 4 : 0 ]

H H H H H H H H H H H H H H H H H H H H H H H H

_R _R _R _R _R _A _A _A _A _A _A _A _A _A _A _A _A _A _A _A _A _A _A _A

E Q# 0 E Q# 1 E Q# 2 E Q# 3 E Q# 4 #1 7 #1 8 #1 9 #2 0 #2 1 #2 2 #2 3 #2 4 #2 5 #2 6 #2 7 #2 8 #2 9 #3 0 #3 1 #3 2 #3 3 #3 4 #3 5

R ESET# R S [0 ]# R S [1 ]# R S [2 ]# TR D Y # H IT # H I TM #

4 H _ D S TB N # 0 4 H_ DS T B P # 0 4 H_ DIN V # 0 4 H _D # [ 63 : 0 ] H_ D# 1 6 H_ D# 1 7 H_ D# 1 8 H_ D# 1 9 H_ D# 2 0 H_ D# 2 1 H_ D# 2 2 H_ D# 2 3 H_ D# 2 4 H_ D# 2 5 H_ D# 2 6 H_ D# 2 7 H_ D# 2 8 H_ D# 2 9 H_ D# 3 0 H_ D# 3 1

H _ DS T B N# 2 4 H _ DS T B P # 2 4 H _ D I N V #2 4 H_ D# 4 8 H_ D# 4 9 H_ D# 5 0 H_ D# 5 1 H_ D# 5 2 H_ D# 5 3 H_ D# 5 4 H_ D# 5 5 H_ D# 5 6 H_ D# 5 7 H_ D# 5 8 H_ D# 5 9 H_ D# 6 0 H_ D# 6 1 H_ D# 6 2 H_ D# 6 3 H _ D # [ 63 : 0 ] 4

4 H _A # [ 3 5 : 3]

4 H _A D S T B # 1 2 2 H _ A 20 M # 2 2 H_ F E RR # 2 2 H _ I GN N E # 22 H _S T P C LK # 2 2 H _ INT R 2 2 H_ NM I 2 2 H _ S MI # H _ A 2 0 M# H_ F E R R# H _ I GN N E # H_ S T P CL K # H_ INT R H_ NM I H_ S M I#

A [1 7 ]# A [1 8 ]# A [1 9 ]# A [2 0 ]# A [2 1 ]# A [2 2 ]# A [2 3 ]# A [2 4 ]# A [2 5 ]# A [2 6 ]# A [2 7 ]# A [2 8 ]# A [2 9 ]# A [3 0 ]# A [3 1 ]# A [3 2 ]# A [3 3 ]# A [3 4 ]# A [3 5 ]# A D S T B [ 1] # A 2 0 M# F ER R# IG NN E # S T P C LK # L INT 0 L INT 1 S M I# R R R R R R R R R S V D[0 1 ] S V D[0 2 ] S V D[0 3 ] S V D[0 4 ] S V D[0 5 ] S V D[0 6 ] S V D[0 7 ] S V D[0 8 ] S V D[0 9 ]

XDP/ITP SIGNA LS

B P M [0 ]# B P M [1 ]# B P M [2 ]# B P M [3 ]# P R DY # P RE Q # T CK T DI T DO T MS TR S T # DB R #

80

54 . 9 _ 1% _ 0 4

1 . 05 V S

TH ERMALP R O C H OT # T HE RM DA T H E RM DC T H E R MT R I P # D2 1 A 24 B 25 C7 H _ P R OC H OT # H _ T H E R MD A H _ T H E R MD C H _ T H R MT R I P # H _P R OC H O T# 2 2

4 H _ D S TB N # 1 4 H_ DS T B P # 1 4 H_ DIN V # 1 Z0210 * 1 K _0 4 Z0211 * 1 K _0 4 Z0212 C 5 5 4 * . 1 U _ 1 0V _ X 7 R _ 04 Z 0 2 1 3 Z0214 Z0215 Z0216 C P U_ B S E L 0 25 C P U _ B S E L 0 C P U_ B S E L 1 25 C P U _ B S E L 1 C P U_ B S E L 2 25 C P U _ B S E L 2 R4 5 8 R1 2 6 C P U _ GT L R E F R 40 7

D[1 6 ]# D[1 7 ]# D[1 8 ]# D[1 9 ]# D[2 0 ]# D[2 1 ]# D[2 2 ]# D[2 3 ]# D[2 4 ]# D[2 5 ]# D[2 6 ]# D[2 7 ]# D[2 8 ]# D[2 9 ]# D[3 0 ]# D[3 1 ]# D S T B N [ 1] # DS T B P [1 ]# DIN V [1 ]# GT L R E F T E S T1 T E S T2 T E S T3 T E S T4 T E S T5 T E S T6 T E S T7 B S E L [0 ] B S E L [1 ] B S E L [2 ] P e n ry n 1 K _ 1% _ 0 4

D [ 48 ] # D [ 49 ] # D [ 50 ] # D [ 51 ] # D [ 52 ] # D [ 53 ] # D [ 54 ] # D [ 55 ] # D [ 56 ] # D [ 57 ] # D [ 58 ] # D [ 59 ] # D [ 60 ] # D [ 61 ] # D [ 62 ] # D [ 63 ] # DS T B N[3 ]# DS T B P [3 ]# D INV [3 ]# CO CO CO CO MP [ 0 ] MP [ 1 ] MP [ 2 ] MP [ 3 ]

Sheet 2 of 48 Penryn (Socket-P) 1/2

DA GRP 3 TA

RESERVED

ADDR GRO UP_1 ICH

B.Schematic Diagrams

M ISC

DATA GR 1 P

H _ DS T B N# 3 4 H _ DS T B P # 3 4 H _ D I N V #3 4 C OM P 0 C OM P 1 C OM P 2 C OM P 3 H _ D P R S TP # 6 , 3 7 H _ DP S L P # 6 R 12 0 *0 _ 0 4 H _ P W RG D 4 H _ C P U S LP # 2 2 P S I# 3 7

H _ TH R M TR I P # 22

If u se d M6 72 th an d el R 3H_ DP W R # 4

HCLKB C L K [ 0] B C L K [ 1]

A 22 A 21

H _C LK _C P U 2 5 H _C LK _C P U # 2 5

D P RS T P # DP S L P # D P W R# P W R G OOD SL P# P S I#

H_ DP S L P # H _ D P W R #_ R H_ P W RG D H _ C P U S LP # P S I#

Layout Note: C686 Close to TEST4 (Pin AF26)C 55 3

1. 0 5 V S

1. 05 V S

56_04 6-14-5603B-11B1K _0 4 1K _0 4 1K _0 4 68 _ 0 4

C 5 52 . 01 U _ 1 6 V _X 7 R _ 0 4

R 40 6 2 K _ 1 %_ 0 4

R 1 50 R 4 59 R 4 60 R 1 49

1 U _ 6 . 3 V _X 5 R _ 0 6

CPU_GRFE=0.7V Layout Note: 0.5" max, Zo= 55 Ohms

P en ry n

R R R R R R R R R R R

1 25 1 34 1 13 1 31 1 15 1 17 1 32 1 22 1 30 1 14 1 27

56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4 56 _ 0 4

H _ TH R M TR I P # H_ F E RR # H_ S T P CL K # H_ INIT # H _ I GN N E # H _ S MI # H _ A 2 0M # H _ C P U S LP # H_ NM I H_ INT R H_ DP S L P #

If PR OC HO T# is r out ed b etw ee n CPU , IM VP an d MC H, pu ll- up r esi st or ha s to be 6 8 ohm ? 5 %. If n ot us e, pu ll -up r es ist or h as to b e 5 6 oh m ? 5 %

( Si S Re co mma nd at ion 2 00 p)

IF US ED D esk to p CPU , H_ CPU RS T# ,H_ PW RG D, H_B RD ,n eed ad d p ul l hig h re sis to r

Layout note: COMP0, COMP2: COMP1, COMP3: Best estimate layers and 14 layers.C OM P 0 C OM P 1 C OM P 2 C OM P 3

0.5" Max, Zo=27.4 Ohms(20mil) 0.5" Max, Zo=55 Ohms(5mil) is 18 mils wide trace for outer mils wide trace if on internal

R 14 2 3 .3 V

0_ 0 6 V _T H E R M 20MI L

CPU to SB interfaceR 1 08 R 1 16 R 1 06 *5 1 _0 4 *3 3 0_ 0 4 *5 1 _0 4 H_ CP U RS T # H_ P W RG D H_ B R0 #

Q9 * N D S 35 2 A P _ N L S D C 1 80 * . 0 1U _ 16 V _ X 7R _0 4 Z0223

R 74 R1 3 5 G *1 0 0 K _0 4 C 16 3

R8 5 27 . 4 _ 1% _ 0 4

R4 4 1 5 4. 9 _ 1 %_ 0 4

R 44 9 2 7 . 4_ 1 % _0 4

. 1 U _ 1 0 V _X 7 R _ 0 4

Thermal ICZ 02 2 5 1 2 U 7 VD D D + T H E RM A LE R T 4 6 R 1 38 R 1 37 Z 02 2 6 R 1 55 R 1 56 3 5 D G ND S D A TA S C LK 7 8 R 1 58 R 1 57 4 . 7K _0 4 4 . 7K _0 4 1 0K _ 0 4 * 1 0m i _ s h ort l *0 _ 0 4 *1 0 K _ 04 V DD 3 S MD _ C P U _ T H E R M 2 7 S MC _ C P U _ T H E R M 2 7 V DD 3 V _ TH E R M T H E R M_ A L E R T # 27

5 4 . 9 _1 % _0 4

I f us ed M6 72 th an d el R 40 an d add R 42R 1 18 10 _ 0 4 H _ D P W R # _R

D

R R R R R R

1 47 89 73 58 1 48 1 19

56 _ 0 4 56 _ 0 4 15 0 _ 1% _ 0 4 39 . 2 _ 1% _ 0 4 15 0 _ 1% _ 0 4 *5 6 _0 4

H_ IE RR # H_ P RE Q # H _ TD I H _ TM S H_ DB R # H _ D P W R # _R

R1 5 2 R 1 51 *3 3 0 K _0 4 *1 00 K _ 0 4 Z0224 Q1 0 *2 N 7 0 02 W H _ TH E R M D C S H _ TH E R M D A C 16 4 1 0 00 P _ 5 0V _0 4

2 7 T H E R M_ R S T #

G

A S C 75 2 5

1 . 0 5V S 3, 4 , 6 , 7 , 24 , 3 9 3 . 3 V 12 , 1 9 , 20 , 2 2 , 23 , 2 4 , 2 6, 3 1 , 3 2, 3 3 , 3 8, 3 9 , 4 0 V D D 3 2 0, 2 3 , 2 7, 3 4 , 3 5, 3 6 , 3 8, 4 0

C 1 54 R 65 R 57

1 0 0P _5 0 V _ 04 27 . 4 _ 1% _ 0 4 68 0 _ 04

H_ P W RG D H _ TC K H _ TR S T #

Layout Note: Route H_THERMDA and H_THERMDC on same layer. 10 mil trace on 10 mil spacing.

Layout Note: Close to Thermal IC ADM1032 1000p F75383M 2200p

Penryn (Socket-P) 1/2 B - 3

Schematic Diagrams

Penryn (Socket-P) 2/2Check cap for santa rosa platformPLACE NEAR CPUC5 6 4 V C OR E J SKT1 C A7 A9 A1 0 A1 2 A1 3 A1 5 A1 7 A1 8 A2 0 B7 B9 B1 0 B1 2 B1 4 B1 5 B1 7 B1 8 B2 0 C 9 C 10 C 12 C 13 C 15 C 17 C 18 D 9 D 10 D 12 D 14 D 15 D 17 D 18 E7 E9 E1 0 E1 2 E1 3 E1 5 E1 7 E1 8 E2 0 F7 F9 F10 F12 F14 F15 F17 F18 F20 A A7 A A9 AA1 0 AA1 2 AA1 3 AA1 5 AA1 7 AA1 8 AA2 0 A B9 AC 1 0 AB1 0 AB1 2 AB1 4 AB1 5 AB1 7 AB1 8 V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC V CC [ 0 0 1] [ 0 0 2] [ 0 0 3] [ 0 0 4] [ 0 0 5] [ 0 0 6] [ 0 0 7] [ 0 0 8] [ 0 0 9] [ 0 1 0] [ 0 1 1] [ 0 1 2] [ 0 1 3] [ 0 1 4] [ 0 1 5] [ 0 1 6] [ 0 1 7] [ 0 1 8] [ 0 1 9] [ 0 2 0] [ 0 2 1] [ 0 2 2] [ 0 2 3] [ 0 2 4] [ 0 2 5] [ 0 2 6] [ 0 2 7] [ 0 2 8] [ 0 2 9] [ 0 3 0] [ 0 3 1] [ 0 3 2] [ 0 3 3] [ 0 3 4] [ 0 3 5] [ 0 3 6] [ 0 3 7] [ 0 3 8] [ 0 3 9] [ 0 4 0] [ 0 4 1] [ 0 4 2] [ 0 4 3] [ 0 4 4] [ 0 4 5] [ 0 4 6] [ 0 4 7] [ 0 4 8] [ 0 4 9] [ 0 5 0] [ 0 5 1] [ 0 5 2] [ 0 5 3] [ 0 5 4] [ 0 5 5] [ 0 5 6] [ 0 5 7] [ 0 5 8] [ 0 5 9] [ 0 6 0] [ 0 6 1] [ 0 6 2] [ 0 6 3] [ 0 6 4] [ 0 6 5] [ 0 6 6] [ 0 6 7] VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC VC C[0 6 8 ] C[0 6 9 ] C[0 7 0 ] C[0 7 1 ] C[0 7 2 ] C[0 7 3 ] C[0 7 4 ] C[0 7 5 ] C[0 7 6 ] C[0 7 7 ] C[0 7 8 ] C[0 7 9 ] C[0 8 0 ] C[0 8 1 ] C[0 8 2 ] C[0 8 3 ] C[0 8 4 ] C[0 8 5 ] C[0 8 6 ] C[0 8 7 ] C[0 8 8 ] C[0 8 9 ] C[0 9 0 ] C[0 9 1 ] C[0 9 2 ] C[0 9 3 ] C[0 9 4 ] C[0 9 5 ] C[0 9 6 ] C[0 9 7 ] C[0 9 8 ] C[0 9 9 ] C[1 0 0 ] P [0 1 ] P [0 2 ] P [0 3 ] P [0 4 ] P [0 5 ] P [0 6 ] P [0 7 ] P [0 8 ] P [0 9 ] P [1 0 ] P [1 1 ] P [1 2 ] P [1 3 ] P [1 4 ] P [1 5 ] P [1 6 ] AB2 0 AB7 AC 7 AC 9 A C 12 A C 13 A C 15 A C 17 A C 18 AD 7 AD 9 A D 10 A D 12 A D 14 A D 15 A D 17 A D 18 AE9 AE1 0 AE1 2 AE1 3 AE1 5 AE1 7 AE1 8 AE2 0 AF9 AF1 0 AF1 2 AF1 4 AF1 5 AF1 7 AF1 8 AF2 0 G2 1 V6 J6 K6 M6 J21 K2 1 M2 1 N2 1 N6 R2 1 R6 T21 T6 V2 1 W21 B2 6 C2 6 AD 6 AF5 AE5 AF4 AE3 AF3 AE2 Z 03 0 1 V CO RE J SKT 1 D A4 A8 A1 1 A1 4 A1 6 A1 9 A2 3 A F2 B6 B8 B1 1 B1 3 B1 6 B1 9 B2 1 B2 4 C 5 C 8 C 11 C 14 C 16 C 19 C 2 C 22 C 25 D 1 D 4 D 8 D 11 D 13 D 16 D 19 D 23 D 26 E3 E6 E8 E1 1 E1 4 E1 6 E1 9 E2 1 E2 4 F5 F8 F11 F13 F16 F19 F2 F22 F25 G 4 G 1 G 23 G 26 H 3 H 6 H 21 H 24 J2 J5 J22 J25 K1 K4 K2 3 K2 6 L3 L6 L21 L24 M2 M5 M 22 M 25 N 1 N 4 N 23 N 26 P3 VSS[0 0 1 ] VSS[0 0 2 ] VSS[0 0 3 ] VSS[0 0 4 ] VSS[0 0 5 ] VSS[0 0 6 ] VSS[0 0 7 ] VSS[0 0 8 ] VSS[0 0 9 ] VSS[0 1 0 ] VSS[0 1 1 ] VSS[0 1 2 ] VSS[0 1 3 ] VSS[0 1 4 ] VSS[0 1 5 ] VSS[0 1 6 ] VSS[0 1 7 ] VSS[0 1 8 ] VSS[0 1 9 ] VSS[0 2 0 ] VSS[0 2 1 ] VSS[0 2 2 ] VSS[0 2 3 ] VSS[0 2 4 ] VSS[0 2 5 ] VSS[0 2 6 ] VSS[0 2 7 ] VSS[0 2 8 ] VSS[0 2 9 ] VSS[0 3 0 ] VSS[0 3 1 ] VSS[0 3 2 ] VSS[0 3 3 ] VSS[0 3 4 ] VSS[0 3 5 ] VSS[0 3 6 ] VSS[0 3 7 ] VSS[0 3 8 ] VSS[0 3 9 ] VSS[0 4 0 ] VSS[0 4 1 ] VSS[0 4 2 ] VSS[0 4 3 ] VSS[0 4 4 ] VSS[0 4 5 ] VSS[0 4 6 ] VSS[0 4 7 ] VSS[0 4 8 ] VSS[0 4 9 ] VSS[0 5 0 ] VSS[0 5 1 ] VSS[0 5 2 ] VSS[0 5 3 ] VSS[0 5 4 ] VSS[0 5 5 ] VSS[0 5 6 ] VSS[0 5 7 ] VSS[0 5 8 ] VSS[0 5 9 ] VSS[0 6 0 ] VSS[0 6 1 ] VSS[0 6 2 ] VSS[0 6 3 ] VSS[0 6 4 ] VSS[0 6 5 ] VSS[0 6 6 ] VSS[0 6 7 ] VSS[0 6 8 ] VSS[0 6 9 ] VSS[0 7 0 ] VSS[0 7 1 ] VSS[0 7 2 ] VSS[0 7 3 ] VSS[0 7 4 ] VSS[0 7 5 ] VSS[0 7 6 ] VSS[0 7 7 ] VSS[0 7 8 ] VSS[0 7 9 ] VSS[0 8 0 ] VSS[0 8 1 ] P e n ry n . VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS [ 08 2 ] [ 08 3 ] [ 08 4 ] [ 08 5 ] [ 08 6 ] [ 08 7 ] [ 08 8 ] [ 08 9 ] [ 09 0 ] [ 09 1 ] [ 09 2 ] [ 09 3 ] [ 09 4 ] [ 09 5 ] [ 09 6 ] [ 09 7 ] [ 09 8 ] [ 09 9 ] [ 10 0 ] [ 10 1 ] [ 10 2 ] [ 10 3 ] [ 10 4 ] [ 10 5 ] [ 10 6 ] [ 10 7 ] [ 10 8 ] [ 10 9 ] [ 11 0 ] [ 11 1 ] [ 11 2 ] [ 11 3 ] [ 11 4 ] [ 11 5 ] [ 11 6 ] [ 11 7 ] [ 11 8 ] [ 11 9 ] [ 12 0 ] [ 12 1 ] [ 12 2 ] [ 12 3 ] [ 12 4 ] [ 12 5 ] [ 12 6 ] [ 12 7 ] [ 12 8 ] [ 12 9 ] [ 13 0 ] [ 13 1 ] [ 13 2 ] [ 13 3 ] [ 13 4 ] [ 13 5 ] [ 13 6 ] [ 13 7 ] [ 13 8 ] [ 13 9 ] [ 14 0 ] [ 14 1 ] [ 14 2 ] [ 14 3 ] [ 14 4 ] [ 14 5 ] [ 14 6 ] [ 14 7 ] [ 14 8 ] [ 14 9 ] [ 15 0 ] [ 15 1 ] [ 15 2 ] [ 15 3 ] [ 15 4 ] [ 15 5 ] [ 15 6 ] [ 15 7 ] [ 15 8 ] [ 15 9 ] [ 16 0 ] [ 16 1 ] [ 16 2 ] [ 16 3 ] P 6 P 21 P 24 R 2 R 5 R 22 R 25 T1 T4 T23 T26 U 3 U 6 U 21 U 24 V 2 V 5 V 22 V 25 W 1 W 4 W 23 W 26 Y 3 Y 6 Y 21 Y 24 A A2 A A5 A A8 A A1 1 A A1 4 A A1 6 A A1 9 A A2 2 A A2 5 A B1 A B4 A B8 A B1 1 A B1 3 A B1 6 A B1 9 A B2 3 A B2 6 A C3 A C6 A C8 A C1 1 A C1 4 A C1 6 A C1 9 A C2 1 A C2 4 A D2 A D5 A D8 A D1 1 A D1 3 A D1 6 A D1 9 A D2 2 A D2 5 A E1 A E4 A E8 A E1 1 A E1 4 A E1 6 A E1 9 A E2 3 A E2 6 A 2 A F6 A F8 A F11 A F13 A F16 A F19 A F21 A 25 A F25 10 U _ 6. 3 V _ X 5 R _ 0 8 1 0 U _ 6 . 3 V _ X5 R _0 8 1 0 U _ 6 . 3 V _ X 5R _ 08 10 U _6 . 3 V _ X 5 R _ 0 8 1 0U _ 6 . 3V _X 5 R _ 0 8 1 0 U _ 6 . 3 V _ X5 R _ 08 C 57 7 C 95 C5 6 5 C5 6 8 C 58 0

V C OR E

V C OR E

C5 0 10 U _ 6. 3 V _ X 5 R _ 0 8

C 65 1 0 U _ 6 . 3 V _ X5 R _0 8

C 1 23 1 0 U _ 6 . 3 V _ X 5R _ 08

C6 1 10 U _6 . 3 V _ X 5 R _ 0 8

C5 9 3 1 0U _ 6 . 3V _X 5 R _ 0 8

C 59 4 1 0 U _ 6 . 3 V _ X5 R _ 08

B.Schematic Diagrams

V C OR E

6-07-1 0611-7C 0C5 9 10 U _ 6. 3 V _ X 5 R _ 0 8 C 57 5 1 0 U _ 6 . 3 V _ X5 R _0 8 C 1 18 1 0 U _ 6 . 3 V _ X 5R _ 08 C5 6 6 10 U _6 . 3 V _ X 5 R _ 0 8 C1 4 6 1 0U _ 6 . 3V _X 5 R _ 0 8 C 12 9 1 0 U _ 6 . 3 V _ X5 R _ 08

Sheet 3 of 48 Penryn (Socket-P) 2/2

V C OR E

C5 8 4 1U _ 6 . 3V _X 5 R _0 6

C 12 4 1 U _ 6 . 3 V _ X 5R _ 06

C 1 28 1 U _6 . 3 V _ X 5 R _ 0 6

C4 9 1U _ 6. 3V _X 5 R _ 0 6

C5 1 1 U _ 6 . 3 V _ X5 R _0 6

C 75 1 U _ 6 . 3 V _ X 5R _ 0 6

Power Plane 2A1 .0 5 V S

VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC

V C OR E

C1 1 3 1U _ 6 . 3V _X 5 R _0 6

C 10 0 1 U _ 6 . 3 V _ X 5R _ 06

C 88 1 U _6 . 3 V _ X 5 R _ 0 6

C5 8 5 1U _ 6. 3V _X 5 R _ 0 6

C6 8 1 U _ 6 . 3 V _ X5 R _0 6

C 14 0 1 U _ 6 . 3 V _ X 5R _ 0 6

L ayout no te:N r pi B2 ea n 6

130mAC 1 59 1 0 U _ 6 . 3 V _ X 5R _ 08

L1 2 H C B 1 60 8 K F -1 2 1 T2 5 1. 5V S C 16 1 . 0 1 U _ 1 6 V _ X7 R _ 04

V C OR E

V CC A [0 1 ] V CC A [0 2 ] V ID V ID V ID V ID V ID V ID V ID [0 ] [1 ] [2 ] [3 ] [4 ] [5 ] [6 ]

C5 8 3 . 1 U _ 1 0V _X 7 R _0 4

C 85 . 1 U _ 1 0 V _ X 7R _ 04

C 5 72 . 1 U _1 0 V _ X 7 R _ 0 4

C5 8 1 . 1U _ 1 0V _X 7 R _ 0 4

C5 8 2 . 1 U _ 1 0 V _ X7 R _0 4

C 15 5 . 1 U _1 0 V _ X 7R _ 0 4

H H H H H H H

_ V ID _ V ID _ V ID _ V ID _ V ID _ V ID _ V ID

0 1 2 3 4 5 6

H _ V I D [ 6 : 0] V CC S E NS E

37

PLACE NEAR CPU1 . 05 V S

V CC S E NS E

AF7

VCC SEN S E 3 7

V S S S E NS E .

AE7

VSSSEN SE

VSSSEN SE 3 7 R 22 1 0 0 _ 1% _ 0 4

P e n ry n R 21 1 0 0 _ 1% _ 0 4

Layo ut note:Ro e VC EN ut CS SE a nd VS EN SS SE t ce at 2 4 ra s 7. oh ms w h 50 m s sp in it il ac g. Pl e PU a ac nd P wi in 1 D th in ch o CP f U.

C5 7 4 + 15 0 U _4 V _ B 2

C 86 . 1 U _ 1 0 V _ X 7R _ 04

C 1 11 . 1 U _1 0 V _ X 7 R _ 0 4

C4 6 . 1U _ 1 0V _X 7 R _ 0 4

C6 2 . 1 U _ 1 0 V _ X7 R _0 4

5/1 0 1 . 05 V S

V CO RE

C1 2 6 . 1 U _ 1 0V _X 7 R _0 4

C 11 6 . 1 U _ 1 0 V _ X 7R _ 04

C 77 . 1 U _1 0 V _ X 7 R _ 0 4

C1 4 1 . 1U _ 1 0V _X 7 R _ 0 4

C1 3 0 . 1 U _ 1 0 V _ X7 R _0 4

C 67 . 1 U _1 0 V _ X 7R _ 0 4

1 . 05 V S 2, 4, 6 , 7 , 2 4 , 3 9 1 . 5V S 6 , 3 3, 3 5 V CO RE 3 7

B - 4 Penryn (Socket-P) 2/2

Schematic Diagrams

SiSM672 Host, PCIE 1/51 .0 5 VS R 1 96 *5 6 _ 04 N B_ PCR EQ # 1. 05 V S 2 , 3 , 6 , 7 , 2 4, 39 1. 2V S 7 , 3 5 1. 8V S 5 , 6 , 7 , 1 1 , 1 3, 14 , 1 5 , 1 7 , 1 9 , 2 1, 22 , 2 3 , 2 4 , 2 5 , 3 5 B 16 C 17 A 17 B 18 W 24 U 24 R 24 N 24 L 21 U 32 C C1 X A V D D C1 X A V S S C4 X A V D D C4 X A V S S HV HV HV HV HV RE F RE F RE F RE F RE F H D0 # H D1 # H D2 # H D3 # H D4 # H D5 # H D6 # H D7 # H D8 # H D9 # H D1 0 # H D1 1 # H D1 2 # H D1 3 # H D1 4 # H D1 5 # H D1 6 # H D1 7 # H D1 8 # H D1 9 # H D2 0 # H D2 1 # H D2 2 # H D2 3 # H D2 4 # H D2 5 # H D2 6 # H D2 7 # H D2 8 # H D2 9 # H D3 0 # H D3 1 # H D3 2 # H D3 3 # H D3 4 # H D3 5 # H D3 6 # H D3 7 # H D3 8 # H D3 9 # H D4 0 # H D4 1 # H D4 2 # H D4 3 # H D4 4 # H D4 5 # H D4 6 # H D4 7 # H D4 8 # H D4 9 # H D5 0 # H D5 1 # H D5 2 # H D5 3 # H D5 4 # H D5 5 # H D5 6 # H D5 7 # H D5 8 # H D5 9 # H D6 0 # H D6 1 # H D6 2 # H D6 3 # N 29 M 30 M 28 L30 L29 K2 8 K3 1 K3 0 H 31 G 34 H 32 G 32 K3 2 F34 F33 F32 H 28 J30 H 30 G 29 J29 G 30 F30 D 33 D 34 B3 2 B3 3 C 34 D 31 A3 2 A3 1 C 31 B3 0 C 30 A3 0 D 28 G 28 C 29 C 28 E2 8 E2 7 C 27 G 26 E2 6 D 26 B2 6 A2 6 C 26 G 22 C 24 A2 5 B2 4 C 25 A2 4 E2 3 E2 5 G 24 D 22 C 22 E2 2 C 23 A2 3 A2 2 B2 2 H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H H _ D# 0 _ D# 1 _ D# 2 _ D# 3 _ D# 4 _ D# 5 _ D# 6 _ D# 7 _ D# 8 _ D# 9 _ D# 1 0 _ D# 1 1 _ D# 1 2 _ D# 1 3 _ D# 1 4 _ D# 1 5 _ D# 1 6 _ D# 1 7 _ D# 1 8 _ D# 1 9 _ D# 2 0 _ D# 2 1 _ D# 2 2 _ D# 2 3 _ D# 2 4 _ D# 2 5 _ D# 2 6 _ D# 2 7 _ D# 2 8 _ D# 2 9 _ D# 3 0 _ D# 3 1 _ D# 3 2 _ D# 3 3 _ D# 3 4 _ D# 3 5 _ D# 3 6 _ D# 3 7 _ D# 3 8 _ D# 3 9 _ D# 4 0 _ D# 4 1 _ D# 4 2 _ D# 4 3 _ D# 4 4 _ D# 4 5 _ D# 4 6 _ D# 4 7 _ D# 4 8 _ D# 4 9 _ D# 5 0 _ D# 5 1 _ D# 5 2 _ D# 5 3 _ D# 5 4 _ D# 5 5 _ D# 5 6 _ D# 5 7 _ D# 5 8 _ D# 5 9 _ D# 6 0 _ D# 6 1 _ D# 6 2 _ D# 6 3 H _ D# [6 3 :0 ] 2 1. 2 V S L23 H C B 1 0 0 5 K F -1 2 1 T 2 0 NB _ P CIE _ 1 .2 V S C 1 XAVD D C1 X A V S S C 4 XAVD D C4 X A V S S N B _ G T LR E F

77mAU 32 D C 262 . 1U _ 1 0 V _ X7 R _ 0 4 P 7 R 7 T7 U 7 V 7 D 7 G 16 E 4 E 5 F 1 G 1 H 3 H 2 H 1 J1 K 1 K 2 L1 M1 N 1 N 2 P 1 R 1 T1 T2 U 1 V 1 W 1 W 2 Y 1 AA 1 AB 1 AB 2 AC 1 AD 1 AE 1 AE 2 AF 1 AG 1 PC PC PC PC PC IE A V D IE A V D IE A V D IE A V D IE A V D D D D D D R EFC L K+ R EFC L KT5 T4 P C I E _ C LK _ N B 25 P C I E _ C LK _ N B # 2 5

C2 6 0 . 0 1U _ 1 6V _ X7 R _ 04

2 3 ,3 3 P CIE _ W A K E # 6 ,2 1 ,2 8 P C I_ INT # A 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R PE0 R X0 X0 # X1 X1 # X2 X2 # X3 X3 # X4 X4 # X5 X5 # X6 X6 # X7 X7 #

PM E# I N TX # PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER PER P0 N 0 P1 N 1 P2 N 2 P3 N 3 P4 N 4 P5 N 5 P6 N 6 P7 N 7 P8 N 8 P9 N 9 P1 0 N 10 P1 1 N 11 P1 2 N 12 P1 3 N 13 P1 4 N 14 P1 5 N 15 PET P0 P E TN 0 PET P1 P E TN 1 PET P2 P E TN 2 PET P3 P E TN 3 PET P4 P E TN 4 PET P5 P E TN 5 PET P6 P E TN 6 PET P7 P E TN 7 PET P8 P E TN 8 P E T P 9 (H D V B P 2 ) P E T N 9 (H D V B N 2 ) P E T P 1 0 (H D V B P 1 ) P E TN 1 0 (H D V B N 1 ) P E T P 1 1 (H D V B P 0 ) P E TN 1 1 (H D V B N 0 ) PETP1 2 P ET N1 2 P E T P 1 3 (H D V A P 2 ) P E TN 1 3 (H D V A N 2 ) P E T P 1 4 (H D V A P 1 ) P E TN 1 4 (H D V A N 1 ) P E T P 1 5 (H D V A P 0 ) P E TN 1 5 (H D V A N 0 ) G 6 H 6 G 4 G 5 J6 K 6 J4 J5 L6 M6 M4 M5 P 6 R 6 P 4 P 5 V 6 W 6 W 4 W 5 Y 6 A A6 A A4 A A5 A B6 A C6 A C4 A C5 A D6 A E6 A E4 A E5 Z0438 Z0439 Z0440 Z0441 Z0442 Z0443 Z0444 Z0445 Z0446 Z0447 Z0448 Z0449 Z0450 Z0451 Z0452 Z0453 Z0454 Z0455 C6 1 6 C6 1 8 C6 1 5 C6 1 7 C6 2 0 C6 2 2 C6 1 9 C6 2 1 C6 2 3 C6 2 4 C6 2 5 C6 2 7 C6 2 8 C6 3 0 C6 2 9 C6 3 1 *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U *. 1 U _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _ 10 V _ X 7 R _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 _0 4 PE PE PE PE PE PE PE PE PE PE PE PE PE PE PE PE 0T X 0 1 2 0T X 0 # 1 2 0T X 1 1 2 0T X 1 # 1 2 0T X 2 1 2 0T X 2 # 1 2 0T X 3 1 2 0T X 3 # 1 2 0T X 4 1 2 0T X 4 # 1 2 0T X 5 1 2 0T X 5 # 1 2 0T X 6 1 2 0T X 6 # 1 2 0T X 7 1 2 0T X 7 # 1 2

N B_ PCR EQ # Z0401 2 H _ DP W R#

R 34 P 32 E 21

P C RE Q # E D RD Y # N C 2 (D P W R # )

25 H _ C L K _ N B 2 5 H _ CL K _ N B # 2 H _ L OC K # 2 H_ D E F E R # 2 H_ T R DY # 2 H _ CP UR ST # 2 H _ PW R G D 2 H _ BPR I# 2 H_ B R 0 # 2 H_ R S # 0 2 H_ R S # 1 2 H_ R S # 2 2 H_ A D S # 2 H _ HIT M # 2 H _ HIT # 2 H _ DR DY # 2 H_ D B SY # 2 H _ B NR # 2 H _ R E Q# [ 4 : 0 ]

F 18 G 18 L 32 P 30 P 31 F 21 P 28 N 30 P 33 K 34 M 31 K 33 M 34 N 34 N 32 M 33 L 34 M 32 H_ R H_ R H_ R H_ R H_ R EQ EQ EQ EQ EQ #0 #1 #2 #3 #4 T 34 R 30 R 29 R 32 P 34

CP UC L K CP UC L K # HL O CK # DE F E R # HT R DY # CP UR S T # CP UP W RG D BPR I# B R E Q0 # R S 0# R S 1# R S 2# AD S# HIT M # HIT # DR D Y # DB S Y # B N R# HR HR HR HR HR EQ EQ EQ EQ EQ 0# 1# 2# 3# 4#

PCIE

B.Schematic Diagrams

Host

Z0402 Z0403 Z0404 Z0405 Z0406 Z0407 Z0408 Z0409 Z0410 Z0411 Z0412 Z0413 Z0414 Z0415 Z0416 Z0417

Z0462 Z0463

HD H D HD H D HD H D

VBP VBN VBP VBN VBP VBN

2 2 1 1 0 0

11 11 11 11 11 11

HD H D HD H D HD H D

VAP VAN VAP VAN VAP VAN

2 2 1 1 0 0

11 11 11 11 11 11

Sheet 4 of 48 SiSM672 Host, PCIE 1/5

SiSM 6 7 2

2 H _A D S T B # 0 2 H _A D S T B # 1 2 H _ A # [3 5 :3 ]

U 34 A A 34 H_ A# 3 H_ A# 4 H_ A# 5 H_ A# 6 H_ A# 7 H_ A# 8 H_ A# 9 H_ A# 1 0 H_ A# 1 1 H_ A# 1 2 H_ A# 1 3 H_ A# 1 4 H_ A# 1 5 H_ A# 1 6 H_ A# 1 7 H_ A# 1 8 H_ A# 1 9 H_ A# 2 0 H_ A# 2 1 H_ A# 2 2 H_ A# 2 3 H_ A# 2 4 H_ A# 2 5 H_ A# 2 6 H_ A# 2 7 H_ A# 2 8 H_ A# 2 9 H_ A# 3 0 H_ A# 3 1 H_ A# 3 2 H_ A# 3 3 H_ A# 3 4 H_ A# 3 5 T 32 T 28 T 31 T 33 T 30 U 32 U 30 V 34 U 29 V 33 V 32 V 28 V 31 W 34 Y 33 W 32 V 30 W 30 Y 34 Y 28 W 29 Y 32 Y 30 Y 31 A A 32 A A 30 A A 29 A B 33 A B 34 A B 32 A C 34 A B 30 A B 31

HA S T B 0 # HA S T B 1 # HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA HA 3# 4# 5# 6# 7# 8# 9# 10 # 11 # 12 # 13 # 14 # 15 # 16 # 17 # 18 # 19 # 20 # 21 # 22 # 23 # 24 # 25 # 26 # 27 # 28 # 29 # 30 # 31 # 32 # 33 # 34 # 35 #

INTERNAL VGA( M740S ) : R EXTERNAL VGA ( M760SU ) : 0.1U

D BI0 # D BI1 # D BI2 # D BI3 # H H H H H H H H DS T B DS T B DS T B DS T B D D D D N0 # N1 # N2 # N3 #

J32 E3 2 F27 F23 H 33 E3 1 B2 8 D 24 H 34 D 32 A2 8 E2 4 A2 1 C 21 N B _ CO M P N B _ CO M P #

H _ DI NV # 0 2 H _ DI NV # 1 2 H _ DI NV # 2 2 H _ DI NV # 3 2 H H H H H H H H _ DS _ DS _ DS _ DS _ DS _ DS _ DS _ DS TB TB TB TB TB TB TB TB N# 0 N# 1 N# 2 N# 3 P# 0 P# 1 P# 2 P# 3 2 2 2 2 2 2 2 2 1 10 _ 1 % _ 0 6

ST BP0 # ST BP1 # ST BP2 # ST BP3 #

H PCO M P HN CO M P

R 17 8

R 18 3

1 0_ 1 % _ 0 4

S i S M 6 72

1 .0 5 V S

1. 05 V S

R1 9 5 1 .8 VS L65 H C B 10 0 5 K F -1 2 1 T 2 0 C 1 XAVD D 1 .8 V S L18 H C B 1 0 0 5 K F -1 2 1 T 2 0 C 4 XA V D D 7 5_ 1 % _ 0 4

C 26 4 .0 1 U_ 1 6 V _ X 7 R_ 0 4

NB_GTL REF=0.7VN B _ GT L R E F C 24 0 .0 1 U_ 1 6 V _ X 7 R_ 0 4 R1 9 2 1 50 _ 1 % _ 0 4 C 27 3 .0 1 U_ 1 6 V _ X 7 R_ 0 4 C2 5 5 .1 U_ 1 0 V _ X 7 R_ 0 4

C 598 1 0 U _1 0 V _ 0 8 N C 10 N C _0 4

C 60 5 .1 U_ 1 0 V _ X 7 R_ 0 4

C 6 06 . 0 1 U _1 6 V _ X 7 R _ 0 4

C 2 10 1 0 U_ 1 0 V _ 0 8 N C2 N C _0 4

C2 3 0 .1 U_ 1 0 V _ X 7 R_ 0 4

C1 X A V S S

C4 X A V S S

Place unde M671MX r solder sid e

SiSM672 Host, PCIE 1/5 B - 5

Schematic Diagrams

SiSM672 DRAM 2/59 , 1 0 M_ A _ D Q [ 6 3: 0] U3 2 B M M M M M M M M _A _A _A _A _A _A _A _A _D _D _D _D _D _D _D _D Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 A D3 1 A D3 0 A G3 4 AE2 9 AE3 2 AF3 4 AF3 1 AE3 0 A D2 8 AF3 2 AF3 3 AF2 8 A J3 4 A H3 1 A G3 0 AF3 0 A G3 2 A J3 2 A J3 1 A H3 4 A H3 2 A H3 3 AK3 4 A H3 0 A L3 2 A M3 3 AK3 2 A G2 9 A M3 4 A L3 1 A J3 0 AK3 3 A L3 4 A M3 2 AP3 2 AP3 1 A M2 9 AK3 0 AK2 9 A J2 7 AK2 8 A N3 2 A M3 0 A M3 1 AK2 0 A M2 0 A M1 9 A J1 9 A N2 0 A J2 1 AP1 9 A H2 0 AK2 1 AK1 9 A L1 9 AK1 8 A J1 7 AK1 7 AP1 6 A H1 8 AP1 8 A N1 8 AP1 7 A M1 8 A L1 7 A M1 7 A N1 6 AK1 6 A N1 4 A J1 5 AP1 5 A M1 6 AK1 5 AP1 4 A H1 6 A L1 5 A M1 5 A L1 3 A M1 3 A M1 2 A J1 3 A M1 4 AK1 4 A N1 2 A H1 4 AK1 3 AP1 2 AP1 3 M M M M M M M M D D D M M M M M M M M D D D M M M M M M M M D D D M M M M M M M M D D D M M M M M M M M D D D M M M M M M M M D D D M M M M M M M M D D D M M M M M M M M D D D D0 A D1 A D2 A D3 A D4 A D5 A D6 A D7 A QM 0 A QS 0 A QS 0 A # D8 A D9 A D1 0 A D1 1 A D1 2 A D1 3 A D1 4 A D1 5 A QM 1 A QS 1 A QS 1 A # D1 6 A D1 7 A D1 8 A D1 9 A D2 0 A D2 1 A D2 2 A D2 3 A QM 2 A QS 2 A QS 2 A # D2 4 A D2 5 A D2 6 A D2 7 A D2 8 A D2 9 A D3 0 A D3 1 A QM 3 A QS 3 A QS 3 A # D3 2 A D3 3 A D3 4 A D3 5 A D3 6 A D3 7 A D3 8 A D3 9 A QM 4 A QS 4 A QS 4 A # D4 0 A D4 1 A D4 2 A D4 3 A D4 4 A D4 5 A D4 6 A D4 7 A QM 5 A QS 5 A QS 5 A # D4 8 A D4 9 A D5 0 A D5 1 A D5 2 A D5 3 A D5 4 A D5 5 A QM 6 A QS 6 A QS 6 A # D5 6 A D5 7 A D5 8 A D5 9 A D6 0 A D6 1 A D6 2 A D6 3 A QM 7 A QS 7 A QS 7 A #

D1 X A V D D D1 XAVSS D4 X A V D D D4 XAVSS

A 15 B 15 A P1 1 A P1 0

D 1X A V D D D 1X A V S S D 4X A V D D D 4X A V S S

1 . 8V S L6 4 C 59 7 1 0 U _ 1 0V _0 8 N C1 2 N C _0 4 H C B 1 0 0 5K F -1 21 T 2 0 C 611

D 1X A V D D

C6 1 2 . 0 1U _ 16 V _ X 7 R _ 0 4

. 1U _ 10 V _ X 7 R _ 0 4

9, 10 M _ D M 0 9, 1 0 M _D QS 0 9 , 1 0 M_ D QS 0 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

D1 X A V S S

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q8 Q9 Q1 0 Q1 1 Q1 2 Q1 3 Q1 4 Q1 5

B.Schematic Diagrams

1 . 8V S L6 7 H C B 1 0 0 5K F -1 21 T 2 0

D 4X A V D D

9, 10 M _ D M 1 9, 1 0 M _D QS 1 9 , 1 0 M_ D QS 1 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

C 65 6

C 658 . 1U _ 10 V _ X 7 R _ 0 4 N C _0 4

C6 5 5 . 0 1U _ 16 V _ X 7 R _ 0 4

Sheet 5 of 48 SiSM672 DRAM 2/51 .8 V

1 0 U _ 1 0V _0 8 N C1 3

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q1 6 Q1 7 Q1 8 Q1 9 Q2 0 Q2 1 Q2 2 Q2 3

DRAM

MA 0 A MA 1 A MA 2 A MA 3 A MA 4 A MA 5 A MA 6 A MA 7 A MA 8 A MA 9 A MA 1 0 A MA 1 1 A MA 1 2 A MA 1 3 A MA 1 4 A MA 1 5 A MA 1 6 A MA 1 7 A R ASA# C ASA# W EA#

A A A A A A A A A A A A A A A A A A

H2 4 P2 5 M2 5 L2 5 P2 6 M2 6 N2 6 K2 5 P2 7 P2 8 K2 4 N2 4 P2 4 M2 8 M2 7 N2 8 P2 1 P2 9

M M M M M M M M M M M M M M M M M M

_ A_ A0 _ A_ A1 _ A_ A2 _ A_ A3 _ A_ A4 _ A_ A5 _ A_ A6 _ A_ A7 _ A_ A8 _ A_ A9 _ A_ A1 0 _ A_ A1 1 _ A_ A1 2 _ A_ A1 3 _ A_ A1 4 _ A_ A1 5 _ A_ A1 6 _ A_ A1 7

M _ A _ A [ 1 7: 0]

9, 1 0

D4 X A V S S

9, 10 M _ D M 2 9, 1 0 M _D QS 2 9 , 1 0 M_ D QS 2 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

A M2 3 A P2 2 A J2 3

M_ F W D S D C L K O A _ D M _ RA S # 9 ,1 0 M _ CA S # 9 ,1 0 M _ W E# 9 ,1 0 M _ F W D S D C LK OA _ D _R M _ F W D S D C LK OA _ D #_ R R2 2 0 R2 1 9 * 10 m i l _s h o rt * 10 m i l _s h o rt M_ F W D S D C L K OA _D M_ F W D S D C L K OA _D # M_ F W D S D C L K O A _ D #

C 2 91 C 2 90

* 10 P _ 5 0 V _ 04 * 10 P _ 5 0 V _ 04

? ? ? ?M_ F W D S D C L K O A _ D 2 5 M_ F W D S D C L K O A _ D # 2 5

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q2 4 Q2 5 Q2 6 Q2 7 Q2 8 Q2 9 Q3 0 Q3 1

F W D S D C LK OA F W D S D C L K OA #

A K1 2 A H1 2

D0 3CS 0 A # CS 1 A # CS 2 A # CS 3 A # A A A A A A A A P2 3 H2 2 M2 2 M2 1 K2 2 P2 0 N2 2 L2 1 M M M M _ CS 0 # _ CS 1 # _ CS 2 # _ CS 3 # 9 ,1 0 9 ,1 0 10 10

R 20 7 1 K _ 1 %_ 0 4

C2 8 9 . 1U _ 10 V _ X 7 R _ 0 4

M_DDR VREF=0.9 VM_ D D R V R E F R 20 8 1 K _ 1 %_ 0 4 C2 8 8 . 1U _ 10 V _ X 7 R _ 0 4 C 2 87 . 1 U _1 0 V _ X 7 R _ 0 4

9, 10 M _ D M 3 9, 1 0 M _D QS 3 9 , 1 0 M_ D QS 3 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

Place c lose to M671MX

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q3 2 Q3 3 Q3 4 Q3 5 Q3 6 Q3 7 Q3 8 Q3 9

O DT 0 A O DT 1 A O DT 2 A O DT 3 A

M _ OD T0 9 , 1 0 M _ OD T1 9 , 1 0 M _ OD T2 1 0 M _ OD T3 1 0

Place under M671MX solde side r

9, 10 M _ D M 4 9, 1 0 M _D QS 4 9 , 1 0 M_ D QS 4 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

C C C C

KEA0 KEA1 KEA2 KEA3

A N3 0 A P3 0 A H2 6 A K2 7

M M M M

_ CK E 0 _ CK E 1 _ CK E 2 _ CK E 3

9 ,1 0 9 ,1 0 10 10

1. 8 V M _C OM P _ N R2 0 5 3 6 _1 % _ 0 6

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q4 0 Q4 1 Q4 2 Q4 3 Q4 4 Q4 5 Q4 6 Q4 7

M _C OM P _ P

R2 1 3

3 6 _1 % _ 0 6

DD RV RE F 0 DD RV RE F 1

A D1 8 A D2 3

M _D D R V R E F

1. 8 V D D R C O MP D D R C OM N A J2 5 A K2 6 M _ C O MP _ P M _ C O MP _ N

9, 10 M _ D M 5 9, 1 0 M _D QS 5 9 , 1 0 M_ D QS 5 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

M_ OCDVREF_P=0.874 VM_ O C D V R E F _P

R2 2 4

40 . 2 _ 1 % _0 4

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q4 8 Q4 9 Q5 0 Q5 1 Q5 2 Q5 3 Q5 4 Q5 5

R2 2 2 OC D V R E F P O CD V RE F N A H2 8 A J2 9 M _ OC D V R E F _ P M _ OC D V R E F _ N

36 _ 1 % _0 6

1. 8 V

9, 10 M _ D M 6 9, 1 0 M _D QS 6 9 , 1 0 M_ D QS 6 # 9 , 1 0 M_ A _ D Q [ 6 3: 0]

M_ OCDVREF_N=0.969 VS 3 A UX S W # B 6 NB _ S 3 A U X S W # 3 1 M_ O C D V R E F _N

R2 0 6

36 _ 1 % _0 6

M M M M M M M M

_A _A _A _A _A _A _A _A

_D _D _D _D _D _D _D _D

Q5 6 Q5 7 Q5 8 Q5 9 Q6 0 Q6 1 Q6 2 Q6 3

R2 1 1

40 . 2 _ 1 % _0 4

9, 10 M _ D M 7 9, 1 0 M _D QS 7 9 , 1 0 M_ D QS 7 #

S S M6 7 2 i

1. 8V 7, 9, 1 0 , 2 2 , 23 , 2 4 , 3 5 , 39 , 4 0 1. 8V S 4 , 6, 7, 1 1 , 1 3 , 1 4, 1 5 , 1 7 , 19 , 2 1 , 2 2 , 23 , 2 4 , 2 5 , 35

B - 6 SiSM672 DRAM 2/5

Schematic Diagrams

SiSM672 MuTIOL VGA 3/51. 8V S 3 .3 V S C 5 26 . 1 U _ 1 0V _ X 7 R _ 04 R 36 5 3 3 _0 4

5 R2 2 1 15 0 _ 1% _ 0 4 C3 0 1 . 1 U _ 1 0V _ X 7 R _ 0 4 Z _V R E F R2 1 4 49 . 9 _ 1% _ 0 4 C3 0 7 . 1 U _ 1 0V _ X 7 R _ 0 4 AH1 0 AP8 A N8 A M7 AL 7 AP4 AP5 ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD ZAD 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AK1 0 A M6 AK1 1 A J1 1 AP7 AJ 9 AP6 A N6 AK9 A M4 AK6 AK8 A N4 AK7 AL 5 A M5 A M8 AL 9 AP9 A M9 U 32 A Z CL K Z DR E Q Z UR E Q Z STB0 Z STB0 # Z STB1 Z STB1 # Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD Z AD 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 EN TEST T E S TM OD E 0 T E S TM OD E 1 T E S TM OD E 2 TR AP0 TR AP1 TR AP2 TR AP3 TR AP4 TR AP5 TR AP6 TR AP7 TR AP8 TR AP9 TR A P 1 0 F15 D1 6 E1 6 F16 D1 7 E1 7 F17 NB _ E NT E S T N B _ T E S TM OD E 0 N B _ T E S TM OD E 1 N B _ T E S TM OD E 2 Z 06 0 2 Z 06 0 3 Z 06 0 4 22 S B _ D P R S L P V R R3 5 2 3 3_ 0 4 Z 0 6 17 C5 1 9 *1 0 0P _ 5 0 V _0 4 3 1 2

U 26 4 Z0618

25 Z _ C L K 0 21 Z D R E Q 21 Z U R E Q 21 Z S T B _ D 0 2 1 Z S T B _ D# 0 21 Z S T B _ D 1 2 1 Z S T B _ D# 1 2 1 Z A D[1 6 :0 ]

D P R S T P #_ I N V

7 4 L V