1 2 WiFi-102 LED Controller With the improvement of people's living standard, more and more products are linked to mobile devices like smart phones, tablet PCs, which makes life simple and intelligence. Using the emerging mobile device to control LED lighting products becomes the aspirations of each customer. As a result, WiFi-102 controller appeared, with the installation of controlling software on mobile devices like Android & IOS phones, tablet PCs. they can remote control LED lighting products through WiFi, which makes LED control more intelligent and humanization. One WiFi - 102 controller can be used as dimmer, CT controller, even RGB controller. which means a significant saving to middleman who need to stock up, now one product will realize your three desires. In addition, this model has DIYfunction, Users can get any effect they want based on our controlling software If you don't have any mobile devices with the controlling software at hand, you could also use our touch controller-Tseries (T1,T2,T3) to control it , which provides more choices! WiFi and remote wireless control operate based on the global universal 2.4 GH frequency range, By using the z same 2.4G antenna, the space pollution caused by WiFi and remote control using wireless signal from different frequency range will be largely reduced. WiFi-102 Technical parameters Max 3A*3 L127.6×W73×H44.5mm L135×W80×H50mm 290g -20 ~50 ℃ ℃ Output current Operating temperature Dimensions Weight (G.W) Power supply LED CV SMPS DC12V~DC24V Input voltage Control distance Max 100m Software Technical parameters Android 2.1 or above, IOS4.3 or above, with the wifi function Android(2.2MB), iOS(3.4MB) English Tool Free, Plug-in-free Platform Size Language Category Others T1 T2 T3 Technical parameters , , RGB color change mode 32 fixed modes, 8 DIY modes flexibly control single color, cold warm color, RGB LED lighting fixture Output control Scene mode 9 DC5V built-in Lithium battery ≤30mA 2.4GHZ 30m 1000mAh ≤6 months 30 days L145×W55×H22mm L168×W102×H28mm 200g Input voltage Working current Working frequency RF remote distance Battery capacity Standby tim Normal using time Dimensions Package Size Weight (G.W) Controller operating instructions 3 . Side A Side B Power input/LED output indicator light instructions RUN LINK RX/TX The indicator flashes quickly about 25 seconds during the electric initialization. Flashes once per second after initialization finished. The indicator light stays lit when the mobile device connects with WIFI controller, and turns off when not connected. The indicator light turns on when the controller receives or transmits the WiFi data. Turns off in the free time. EXT Key RJ45 SSID code switch 2. Work status indicator instructions 127.6mm 73mm 44.5mm 1. Install / uninstallANT ANT installation instruction Install the WiFi antenna clockwise, uninstall anticlockwise RUN RX/TX LINK EXT KEY SSID ON/OFF SCENE RUN RX/TX LINK EXT KEY SSID MATCH FUN on/off scene Indicator Note: remote control isanother purchase accessories RoHS COMPLIANT warranty 3 years ISO9001:2008 1. Product arameter p Package size 2. Configuration Diagram
4
Embed
LTECH LTECH WiFi-102 LED Controller manual WiFi-102 LED
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
3 4
3 SSID Number setting.
Use code switch to set the controller's SSID Number-- WIFI-101-SSID-X, X is the code switch numerical value (total
16 No. from 0 to F). which means our product could set 16 isolated LAN in the same area. The controller will re-enter
initialization status once the code switch changes. RUN LED indicator light will flash quickly about 25 seconds, mobile
device need to search and connect WiFi again after Initialization finished.
4. “ON/OFF” “ Scene Key”
Press “ON/OFF “to turn on / off controller
Long press “Scene” to the 1st scene mode. short press Scene to scene mode sequentially , Scene mode changes“ ”
from 1 to 9, then changed back from 9 to 1.
5 EXT Key network port.EXT Key network port is used to connect the external button, 7 signal wires plus 1 GND wire,1# signal wire is the
ON/OFF button,2-7# signal wire represents 1-6 scene mode.
LED controller software instructions4.
(1) Ltech WIFI-100 software installation
this software has two versions -Android & iOS, choose the installation based on your mobile device. Check the
installation and usage of each version below
1) Installation of Android version: Transmit the installation package to the mobile device memory card and
Click to install.
2 installation of iOS version: A. search “WiFi-100 “ in the App store through)
mobile device and install.
B. after connecting the mobile device with PC, search “WiFi-100” in the
through iTunes and install.
Current White
AT&TAT&T 12:34 PM12:34 PM
Current White
Save
SettingsScene
50
W 050
Current White
AT&TAT&T 12:34 PM12:34 PM
Current White
Save
SettingsScene
50
WWW 10050
Current White
AT&TAT&T 12:34 PM12:34 PM
Current White
SettingsStyleEditor Scene
50
Save GR 255255 255B
2 RGB,CT,DIM driver color wheel interface.
Click” Setting “to setting interface, Select RGB, CT or DIM driver to get into each one's color wheel interface.
By touching the color wheel, the color, brightness, color temperature of the connected LED could be adjusted,
the brightness can also be changed by the brightness slider which is above the color wheel.
Save
Dimming mode CT mode RGB mode
Scene save key
parameter values
brightness slider
currentlyselected color
turn on/off thecontroller
Click to restore thedefault white
color wheel
Setting
Modes
Scene interfacekey
RGB editing interface
SettingsStyleEditor Scene
AT&TAT&T 12:34 PM12:34 PM
CurrentCurrent WhiteWhite
Save
50
GR 255255 255B
Wifi is not enable currently!?Do you want to turn it on now
Wifi is not enable currently!
OKOK
WarningWarning
prompt box saying withoutWiFi connection
AT&TAT&T 12:34 PM12:34 PM
SettingsSettings
Wifi Connection
CT Driver
DIM Driver
DriverDriver
setting interface
RGB Driver
return to a previous interface
iOS WiFi connectionAndroid WiFi connection
RUN
RX/TX
LINK
EXTKEY
SSID
ON/O
FFSCENE 0
12
3 4 5 6 78
9A
BCDE
F
1. WiFi connection and settings
( )1 Click mobile devices' WiFi-setting, enable the WiFi function. The system will search automatically and list the
SSID No. for the controller (as shown below). Click the SSID No, to connect.
( )2 Click to Enable software (if the Mobile devices'WiFi function is closed, the prompt box saying without WiFi
connection will pop up. Click “ok” to close the Dialog box and exit the application .go back to step (1) for the WiFi
connection.
Click settings to setting interface. Setting interface is used to switch among RGB, CT, DIM drivers and enter the
WiFi connection interface.
WiFi connection interface is for displaying the information of the connected controller.
Note: Device IP and port number are the fixed value, which are unchangeable.