LPS 1 - Adams Aviation - Aircraft Spares and Accessories · PDF fileLUBRICANT/PENETRANT TECHNICAL DATA SHEET FEATURES LPS 1 ... Vapor pressure

LPS 1®

GREASELESS LUBRICANT

LUBRIC

AN

T/PENETRA

NT

TECH

NIC

AL D

ATA

SHEET

FEATURES

LPS 1® Greaseless Lubricant is specially formulated to penetrate minute crevices, displace moisture, and leave behind a thin, dry lubricating film. It is the top choice for drying out critical electrical/electronic components and lubricating precision instruments.

Approved/Qua lified to: ■ Allied Signal ES-2092

■ Boeing B-737-500 Task 75-31-02-206-001-C00

■ Bombardier (Canadair) BAMS 569-001

■ Delta Airlines

■ Lockheed Martin EPSN G34.031

■ Pratt & Whitney Canada CPMC 79255 Rev. C

■ Rolls Royce Overhaul Process 340

■ Nonfood Compounds Program Listed Category Code: H2 Registration #059847 (Aerosol); #129040 (Bulk)

■ Acceptable for use in Canadian Food Processing Establishments

■ MIL-C-23411A

■ NSN 7930-01-380-9028 (11 wt. oz.)

■ NSN 9150-01-039-4745 (11 wt. oz.)

■ NSN 9150-01-142-9773 (5 gal.)

SPECIFICATIONS AND APPROVALS

■ Provides a dry, thin, lubricating film ■ Resists oil, dust, and dirt build-up ■ Removes carbon build-up from surfaces ■ Displaces moisture ■ Loosens rusted or frozen parts ■ Provides a short term, light, corrosion

resistant barrier ■ Ideal for delicate mechanisms ■ Safe on paint, fabric, and most plastics ■ Non-conductive ■ Used worldwide in aviation ■ VOC compliant in all 50 states ■ NSF® Registered H2 ■ Acceptable for use in Canadian Food

Processing Establishments

Net Contents Part No.

11 wt.oz. / 312 g/ 379 mL aerosol20 fl.oz. (591 mL) trigger spray144 single wipes per case1 gal. (3.78 L)5 gal. (18.93 L)55 gal. (208 L)312 g/ 11 wt.oz. /379 mL aerosol (Canada)

001160012200144011280010500155

C30116

PACKAGE SIZES

APPLICATIONS ■ Cables ■ Circuit Breakers ■ Electric Motors ■ Electronic Connectors ■ Generators

■ Hinges ■ Ignition Systems ■ Locks ■ Micrometers ■ Molds

■ Nuts and Bolts ■ Precision Open Gears ■ Power Tools ■ Relays ■ Sliding Mechanisms

■ Switch Gears ■ Weapon cleaner

H2

©2013 LPS® Laboratories • LPS® and LPS 1® are registered trademarks of Illinois Tool Works • Printed in U.S.A. • All Rights Reserved • Form #TDS_00116 • Rev. 10/2013

LPS® Laboratories • An Illinois Tool Works Company4647 Hugh Howell Road • Tucker, GA 30084 • TEL: (800) 241-8334 or (770) 243-8800 • FAX: (800) 543-1563 or (770) 243-8899Internet Web Site: www.lpslabs.com

LPS 1®

GREASELESS LUBRICANT

MATERIAL SAFETY DATA SHEETS AVAILABLE UPON REQUEST OR VISIT OUR WEB SITE : WWW.LPSLABS.COM

PROPERTIES

Appearance/physical state Liquid Flammable limits (estimated) Upper: 7.0% Lower: 0.6%

Color Pale amber Auto-ignition temperature > 442°F (> 228°C)

Odor Characteristic VOC

Aerosol: <25% per U.S. State and Federal Consumer Product Regulations Bulk: <25% per U.S. State and Federal Consumer Product Regulations

Vapor pressure <0.05 mmHg @ 20°C Evaporation rate < 0.1 (BuAc = 1)Vapor density > 1 Viscosity <3.8 cSt @ 25°CBoiling point 415°F (213°C) Percent volatile 95 – 96%Solubility (water) Not soluble Dielectric strength 32 kVSpecific gravity 0.79 – 0.81 @ 20°C Flash point 175°F (79°C) TCC-dispensed liquid

Scan QR Code to view demo video of LPS 1® or go to http://www.lpslabs.com/product-videos

STORAGEKeep container in a cool, well-ventilated area. Avoid all sources of ignition (spark or flame). Store between 40°F (5°C) and 120°F ( 49°C).

Store aerosols as Level 3 Aerosol (NFPA 30B). Store all materials in a dry, well-ventilated area. Avoid breathing vapors.

Mix well before using. Spray on clean surface. Use attached extension tube for pinpoint application. Safe to use on plastic, rubber and paint. Use only in well ventilated areas. Avoid all sources of ignition (spark or flame).

DIRECTIONS

Waste must be disposed of in accordance with any and all applicable environmental control rules and/or regulations.

DISPOSAL INFORMATION

LPS 2®

HEAVY-DUTY LUBRICANT

LUBRIC

AN

T/PENETRA

NT

TECH

NIC

AL D

ATA

SHEET

FEATURES

LPS 2® Heavy-Duty Lubricant will penetrate, lubricate, and protect against corrosion. Its strong multipurpose capabilities allow its use in a variety of industrial applications. LPS 2® does not contain harmful chlorinated solvents and it is safe for use on most surfaces.

Approved/Qua lified to: ■ Boise Cascade

■ Canadian Food Inspection Agency

■ Chrysler Corporation

■ City Public Service

■ Cummins Engine

■ Dresser Rand

■ Ford Motor Co.

■ Halliburton

■ Honda Corp.

■ Inland Steel

■ Kimberly-Clark

■ Koch Refining Group

■ Kodak

■ Lockheed Martin CPC 2c & 3b lubricating

■ Lockheed Martin EPSN G39.04

■ MIL-C-23411A

■ MIL-C-81309D Type III

■ MIL-PRF-16173E Grade 3 Class 1

■ Minntac - US Steel

■ New York City Transit

■ NSF® International

■ Occidental Chemicals

■ Pratt & Whitney Canada CPMC 79256 Rev. C

■ Shell Oil

■ Tyco Electronics

■ Tyson

■ UPS M-5100-2780-B

SPECIFICATIONS AND APPROVALS

■ Strong, multi-purpose lubricant, and penetrant

■ Provides a non-drying, light, oily film for use on indoor/outdoor equipment

■ Reduces wear caused by friction and corrosion

■ Loosens rusted or frozen parts

■ Provides up to one year of corrosion protection on steel parts

■ Nonfood Compounds Program Listed Category Code: H2 Registration #129026 (aerosol); #059848 (bulk)

Net Contents Part No.

11 wt.oz. / 312 g/ 380 mL aerosol20 fl.oz. (591 mL) trigger spray1 gal. (3.78 L)5 gal. (18.93 L)55 gal. (208 L)312 g/ 11 wt.oz. /379 mL aerosol (Canada)

0021600222021280020500255

C30216

PACKAGE SIZES

APPLICATIONS ■ Bearings & valves

■ Cables & linkages

■ Dies, bits & fasteners

■ Engines & electric motors

■ Metal parts

■ Parts in storage

■ Production equipment

■ Pulleys & rollers

■ Slides & tracks

H2

©2013 LPS® Laboratories • LPS® is a registered trademark of Illinois Tool Works • Printed in U.S.A. • All Rights Reserved • Form #TDS_00216 • Rev. 10/2013

LPS® Laboratories • An Illinois Tool Works Company4647 Hugh Howell Road • Tucker, GA 30084 • TEL: (800) 241-8334 or (770) 243-8800 • FAX: (800) 543-1563 or (770) 243-8899Internet Web Site: www.lpslabs.com

LPS 2®

HEAVY-DUTY LUBRICANT

MATERIAL SAFETY DATA SHEETS AVAILABLE UPON REQUEST OR VISIT OUR WEB SITE : WWW.LPSLABS.COM

PROPERTIES

Appearance/physical state Liquid Flammable limits (estimated) Upper: 7.0% Lower: 0.6%

Color Brown Auto-ignition temperature > 442°F (> 228°C)

Odor Petroleum/cherry VOC

Aerosol: 0% per U.S. State and Federal Consumer Product Regulations Bulk: 0% per U.S. State and Federal Consumer Product Regulations

Vapor pressure <0.05 mmHg @ 20°C Evaporation rate < 0.1 (BuAc = 1)Vapor density 4.7 Viscosity <7 cSt @ 25°CBoiling point 383°F (195°C) Percent volatile 92 – 95%Solubility (water) 3% Dielectric strength 33 kVSpecific gravity 0.82 – 0.86 @ 20°C Flash point 175°F (79°C) TCC-dispensed liquid

STORAGEKeep container in a cool, well-ventilated area. Avoid all sources of ignition (spark or flame). Store between 40°F (5°C) and 120°F ( 49°C).

Store aerosols as Level 3 Aerosol (NFPA 30B). Store all materials in a dry, well-ventilated area. Avoid breathing vapors.

Mix well before using. Spray on clean surface. Use attached extension tube for pinpoint application. Safe to use on plastic, rubber and paint. Use only in well ventilated areas. Avoid all sources of ignition (spark or flame).

DIRECTIONS

Waste must be disposed of in accordance with any and all applicable environmental control rules and/or regulations.

DISPOSAL INFORMATION

LPS 3® PREMIER RUST INHIBITOR

CO

RROSIO

N IN

HIBITO

RTEC

HN

ICA

L DA

TA SH

EET

■ Protects for up to 2 years indoors ■ Prevents rust and corrosion ■ Provides non-sling lubrication ■ Self-healing, soft, waxy film ■ Penetrates to displace moisture ■ Inhibits exfoliation and filiform corrosion

of aluminum ■ Safe on all metals ■ NSF® Certified: H2 Registration # 129027

(Aerosol); # 059849 (Bulk) ■ Acceptable for use in Canadian Food

Processing Establishments

FEATURES

Net Contents Part No.

11 wt.oz. / 312 g/ 380 mL aerosol20 fl.oz (591 mL) trigger spray1 gal. (3.78 L)5 gal. (18.93 L)55 gal. (208 L)312 g/ 11 wt.oz. /380 mL aerosol (Canada)

0031600322031280030500355

C30316

PACKAGE SIZES

H2

LPS 3® Premier Rust Inhibitor is a specially formulated long-term corrosion inhibitor protecting metal parts in inside storage for up to two years. When applied it forms a soft, transparent, waxy film sealing out moisture, air, acid, alkali fumes, and other corrosive elements.

Approved/Qua lified to: ■ ASTM F-945 ■ Bombardier deHavilland DHMS C4.12 Type I Grade 3 ■ Embraer EMB 120 Brasilia C.P.M. 120/1811 Type A-1 ■ Lockheed Martin EPSN G39.2004 ■ Lockheed Martin Heavy Duty CPC 2b ■ McDonnell Douglas DMS 2150 ■ Pratt & Whitney PWA 36604 ■ Pratt & Whitney Canada LCPMC 79133 Rev. D ■ Saab 340 Maintenance Manual ■ United Airlines ■ United Technologies USBI 99606-0012 ■ MIL-C-83933A ■ MIL-PRF-16173E Grade 2 Class 1 ■ NSN 8030-00-118-0666 (11 wt. oz.) ■ NSN 6850-00-363-0841 (1 gal.)

SPECIFICATIONS AND APPROVALS

APPLICATIONS ■ Aircraft fuselages ■ Battery terminals ■ Cables, chains, and pulleys ■ Cargo sections ■ Elevators ■ Interior sections of vehicle doors

■ Metal parts ■ Offshore drilling equipment ■ Outdoor electrical connections ■ Outdoor storage and

shipments ■ Pumps and hose assemblies

©2014 LPS® Laboratories • LPS® , LPS 3® , and PreSolve® are registered trademarks of Illinois Tool Works • Printed in U.S.A. • All Rights Reserved • Form #TDS_00316 • Rev. 1/2014

LPS® Laboratories • An Illinois Tool Works Company4647 Hugh Howell Road • Tucker, GA 30084 • TEL: (800) 241-8334 or (770) 243-8800 • FAX: (800) 543-1563 or (770) 243-8899Internet Web Site: www.lpslabs.com

LPS 3® PREMIER RUST INHIBITOR

MATERIAL SAFETY DATA SHEETS AVAILABLE UPON REQUEST OR VISIT OUR WEB SITE : WWW.LPSLABS.COM

HANDLINGDO NOT spray into or around ignition sources. DO NOT allow material to come in contact with eyes or skin. Wear appropriate protective equipment during handling. Keep container closed. Avoid breathing vapors or mists. Use only with adequate ventilation. Wash hands and contaminated clothing thoroughly after handling.

STORAGE

Keep container in a cool, well-ventilated area. Avoid all sources of ignition (spark or flame). Store between 40°F and 120°F (4.4°C and 49°C).

Store aerosols as Level 3 Aerosol (NFPA 30B). Store all materials in a dry, well-ventilated area. Avoid breathing vapors.

Aerosol: Shake well before using. Hold can 8 to 12 inches away from surface to be sprayed. Apply a light, even coat. For best results use at room temperature, 70°F (21°C). Attach extension tube for difficult to reach areas. Wipe off any excess. If an additional coat is desired, allow a minimum of 3 hours cure before applying second coat. Use only in well ventilated area. Avoid all sources of ignition (spark or flame).

Bulk: Stir container with mechanical stirrer to ensure product consistency. Brush, roll, or spray light even coat onto metal surface using paint sprayer or airless spray equipment. For best results use at room temperature 70°F (21°C). Wipe off any excess. If an additional coat is desired, allow a minimum of 3 hours cure before applying second coat. Use only in well ventilated area. Avoid all sources of ignition (spark or flame).

Always use proper personal protective equipment as listed on MSDS.

DIRECTIONS

Removal Information: Removal of LPS® 3 is best accomplished using a solvent such as LPS® PreSolve® or LPS® A-151 (mineral spirits will suffice but may require more time to remove). Apply degreaser via spraying, brushing or roller. Allow degreaser to dwell for 5 -10 minutes on surface. Agitation on surface with stiff brush may increase the effectiveness. Dwell time may vary depending on corrosion inhibitor thickness. Remove by wiping with absorbent rags or by scraping. Repeat process if complete removal is not achieved. Dispose of waste according to local and federal regulations.

ADDITIONAL INFORMATION

PROPERTIES

Appearance/physical state Hazy Liquid Color Brown

Odor Mild Cherry Vapor pressure Aerosol: ~4860 mmHg @20°CBulk: >1.0mmHg @20°C

Boiling/Condensation point °F(°C) Aerosol: 307°F (153°C)Bulk: 354°F (179°C) Flash point °F(°C) Aerosol: <73°F (23°C)

Bulk: 104°F (40°C)

Specific gravity (water=1) Aerosol: 0.84 – 0.87 @ 20°CBulk: 0.81– 0.83 @ 20°C Flash point method Tag-Closed Cup

Solubility in water Aerosol: 5% in waterBulk: Negligible Auto ignition Temperature °F(°C)

Aerosol: >446°F (230°C) dispensed liquid

Bulk: 469°F (246°C)

VOC

Aerosol: 64% per U.S. State & Federal Consumer Product Regulations

Bulk: 79.1% per U.S. State & Federal Consumer Product Regulations

Pour Point °F(°C) 0°F (-18°C)

Flammable limits (estimated) Lower: 1.0%Upper: 7.0% Viscosity 200 – 600cPs @ 25°C

Volatiles Aerosol: 70% – 80%Bulk: 70% – 90% Coverage per gallon 401 ft2/gallon @ 4 wet mils

Wet Film Thickness 3 – 7 mils Dry Film Thickness 1 – 3 milsHumidity Cabinet Test (ASTM D 1748)

No rust on 1029 steel panels after 30 days

Salt Spray Cabinet Test (ASTM D 177)

No corrosion on 2024-T3 aluminum panels after 1500 hours

Propellant Carbon Dioxide Corrosion Protection Indoors: up to 2 yearsOutdoors: 9 months

Dry Time to Handle 6 – 8 hours Full Cure 24 hours

Dielectric Strength 19.5kV HMIS 1996 Aerosol: 1, 3, 0 Bulk: 1, 2, 0

Temperature Range °F(°C) -40°F – 175°F (-40°C – 79°C) HMIS III Aerosol: 1, 4, 2 Bulk: 1, 2, 0Spray Pattern Cone shaped mist