This section lists works approved by Lloyd’s Register Group for steelmaking and the manufacture of rolled steel plate, strip, sections and bars in accordance with the requirements of LR's Rules and Regulations for the Classification of Ships Part 2, Chapter 3. The information listed for each works is a summary of the product, generic grade and maximum thickness, or in the case of round bars, diameter approved. It is important to note that this List does not provide full details of the grades approved by LR as required by the Rules. The combinations of deoxidation practice ( e.g. killed, semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V, etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included. These parameters may vary within each grade by manufacturer and could influence the fabrication procedures that can be applied. Where required this information should be obtained from the current certificate of approval issued to the manufacturer by LR. Works designated ( Q.A. Approved ) are also approved under the Quality Scheme for Materials in accordance with LR's Rules and Regulations for the Classification of Ships Part 2, Chapter 1 Section 2. The list also includes firms approved for the manufacture of fabricated steel sections and steel by powder metallurgy. Approval only covers the manufacturing location listed, it does not extend to other works owned by the same company. The local LR surveying office is also listed. Abbreviations B.O.S. Basic Oxygen Steelmaking Con Cast Continuous Casting E.A.F. Electric Arc Furnace O.H. Open Hearth NOTICE AND TERMS OF USE Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as the 'Lloyd's Register Group'. The Lloyd's Register Group assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the List 1 Approved Steelmakers and Manufacturers of Rolled Steel Plates, Strip, Sections & Bars As at 06 November 2012
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
This section lists works approved by Lloyd’s Register Group for steelmaking and themanufacture of rolled steel plate, strip, sections and bars in accordance with therequirements of LR's Rules and Regulations for the Classification of Ships Part 2, Chapter 3.
The information listed for each works is a summary of the product, generic grade andmaximum thickness, or in the case of round bars, diameter approved.
It is important to note that this List does not provide full details of the grades approved byLR as required by the Rules. The combinations of deoxidation practice ( e.g. killed,semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included. These parameters may vary within each grade bymanufacturer and could influence the fabrication procedures that can be applied.
Where required this information should be obtained from the current certificate of approvalissued to the manufacturer by LR.
Works designated ( Q.A. Approved ) are also approved under the Quality Scheme forMaterials in accordance with LR's Rules and Regulations for the Classification of ShipsPart 2, Chapter 1 Section 2.
The list also includes firms approved for the manufacture of fabricated steel sections andsteel by powder metallurgy.
Approval only covers the manufacturing location listed, it does not extend to other worksowned by the same company.
The local LR surveying office is also listed.
Abbreviations
B.O.S. Basic Oxygen Steelmaking
Con Cast Continuous Casting
E.A.F. Electric Arc Furnace
O.H. Open Hearth
NOTICE AND TERMS OF USE Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees oragents are, individually and collectively, referred to in this clause as the 'Lloyd's RegisterGroup'. The Lloyd's Register Group assumes no responsibility and shall not be liable to anyperson for any loss, damage or expense caused by reliance on the information or advice inthis document or howsoever provided, unless that person has signed a contract with the
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
As at 06 November 2012
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
As belowB.O.S. / Con CastSteelmakingBLUESCOPE STEEL (AIS) PTY. LTD. SydneyA, B, D, E 51Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
51Higher Strength
A, B, D, E 13Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
6Higher Strength
P.O. Box 1854Wollongong
Port Kembla Steelworks
Tel: +61 2 42754666 Fax: +61 2 42753045 Email: mailto:[email protected] with specified through thickness properties notation Z35 may be added.Normalizing heat treatments carried out by sub-contractor, Bisalloy.
Tel No: +32 433 885 56 Fax No: +32 433 809 00Email : [email protected] : www.esb.beCertificate No: MD00/3858/000/1 Expiry date: 10/11/2013Materials Suitable for Steel Forgings, Pipe and Tube, Ingots up to 800mm diameter and Blooms up to 600 mm diameter
Seraing
As belowE.A.F. / Con CastSteelmakingINDUSTEEL BELGIUM SA AntwerpA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36, EH40 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69, FH42, FH46,FH50, FH55, FH62, FH69
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Rod.Luiz Dumont Villares km 2- Moreira CésarCEP 12442-260
Pindamonhagaba Plant
Tel: +55 12 2126 7174 Fax: +55 12 2126 7325 Email: mailto:[email protected] Web:http://www.gerdau.com.brBars for grade R3 chain cable is restricted to supply to Companhia Brasileira Amarras with specification EC-Gr.3a.Ingots as semi-finished products to the above maximum weight nominal 630mm x 530mm x 2150mm long are accepted for further processing for rolledproducts.Certificate #: MD00/2867/0006/1 Expiry date: 24/03/2014
Pindamonhangaba S.P.
As belowB.O.S. / Con CastSteelmakingUSIMINAS Rio de JaneiroA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
Av. Pedro Linhares Gomes, 5431Distrito Usiminas, CEP 35160-900
Usinas Siderúrgicas de Minas Gerais S/AUsina Intendente Câmera
Tel +55 (0)31 38293136 Fax +55 (0)31 38293516 Email: mailto:[email protected] and Z35 through thickness properties for plates of approved grades in the TM+Acc and TM+Acc+Temper conditionsMaterials Quality Scheme Approved - MQS014Certificate #: MD00/1603/0007/1 Expiry date: 24/06/2014
Ipatinga, Minas Gerais
As belowB.O.S. / Con CastSteelmakingUSINAS SIDERÚRGICAS DE MINAS GERAIS S.A. -USIMINAS
Rodovia Cônego Domênico Rangoni, Km 6Vila da Indústrias 11573-900
Tel: +55 13 3362-2978 Fax: +55 13 3362-3775 Email: mailto: [email protected] Web:http://www.usiminas.comSpecified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.Specified through thickness properties for plates of grades up to DH32 and thickness up to 26mm in the normalised condition, rolled from continuously castslab.Material Quality Scheme approved, MQS 044Certificate #: MD00/1193/0008/1 Expiry date: 29/09/2014
Cubatão - São Paulo
Bulgaria
As belowE.A.F. / Con CastSteelmakingSTOMANA INDUSTRY AD SofiaAs below 200Blooms/BilletsSemi-FinishedA 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Canada
As belowB.O.S. / Con CastSteelmakingESSAR STEEL ALGOMA INC. TorontoD, E 50Normal StrengthPlatesA, B 60AH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
Tel: +86 412 673 4836 Fax: +86 412 672 5766 Email mailto:[email protected] Web http://www.ansteel.con.cnAll grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.Certificate Number: MD00/1869/0009/1 Expiry: 23/03/2015
Liaoning Province
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED DalianNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
Anshan CityLiaoning Province
MEDIUM PLATE MILL OF MEDIUM AND HEAVY PLATE PLANTAngang Area
Tel +86 0412 675 1030 Fax +86 0412 675 2819 Email mailto:[email protected] as semi finished products nominal 2000mm width x nominal 7000mm length to the above maximum thickness are approved for further processing forrolled products.Certificate No. MD00/2757/0007/1 Expiry date: 23/10/2014
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED DalianA, B, D 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
A, B, D 22Normal StrengthHot Rolled CoilAH32, AH36 12Higher Strength460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22
No 885, Fujin RoadBaoshan District
Core Base
Tel +86 21 2664 8888 Fax +86 21 2664 8000 Web:http://www.baosteel.comIncluding all plate grades and thicknesses with specified through thickness properties (Z35)Semi Finished Products - Killed for further processing for forgings, Fine Grain for further processing for rolled products.Certificate #: MD00/1343/0013/1 Expiry date: 30/03/2013
Materials Quality Scheme Approved - MQS 038
Shanghai 201900
As belowB.O.S. / Con CastSteelmakingBAOSHAN IRON & STEEL CO., LTD. Shanghai Portcarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D, E 60Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Baoshan DistrictShanghai 200949
Core Base Plate Line No. 2No. 777 North Wenchuan Road
Tel +86 21 266488888 Fax +86 21 2664 8000 Email: to: [email protected] Web:http://www.baosteel.com
Semi-finished products in carbon, carbon-manganese fine grain (element combinations as stated, slabs to 2300mm wide, to 12000mm long to 54 tonnes for furtherprocessing to rolled products
Z25 & Z35 designations made be added for plates up to 35mm thick produced in the as rolled condition from concast slab for grades A, B and D with specifiedthrough thickness properties
Z25 & Z35 designations made be added for plates with specified through thickness properties for the approved grades in the normalised condition, normalisedrolled condition, TM condition and TM +Acc condition
Z25 & Z35 designations made be added for plates up to 40mm thick produced in the normalised rolled condition from concast slab for grades DH36 and DH32with specified through thickness properties
As belowB.O.S. / Con CastSteelmakingBENGANG STEEL PLATES CO., LTD. Daliancarbon, carbon-manganese 220SlabsSemi-FinishedA, B 20Normal StrengthHot Rolled CoilA, B 20Normal StrengthPlates from coils
Semi Finished products Carbon and Carbon-manganese, Fine Grain Al, slabs to 2100mm wide, to 9000mm long; Blooms to 400mm wide, to 12m long, for furtherprocessing for Rolled Products.
117017
A, B, D 14Normal StrengthSectionsCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinAH27S, AH32, AH36 14Higher Strength
Chongqing Iron and Steel Co., Ltd.Jiagnan Town (4100 Mill)
Tel: +82 623 6884 2716 Fax: +82 623 6884 9574 Email: [email protected] Web: http://www.cggfSlabs as semi finished products nominal 2500mm width x 12000mm length to the above maximum thickness are approved for further processing for rolledproducts.Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to Normal Strength Grades in the Normalised supplycondition and Normalizing Rolled supply condition.Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to Higher Strength Grades in the Normalised supplycondition and in the TM supply condition .Certificate Number: MD00/3763/0004/1 Expiry date: 29/03/2013
A, B, D, E 40Normal StrengthPlatesCISCO WuhanAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG
40Boiler & Pressure Vessel
Chongqing Iron and Steel Co., Ltd.Jiagnan Town (2700 Mill)Tel: +82 623 6887 3543 Fax: +82 623 6887 3543 Email: [email protected] Web: http://www.cggfPlates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to all Grades and supply conditions.Certificate Number: MD00/3982/0002/1 Expiry: 26/01/2015
As belowE.A.F./Ingot/Con CastSteelmakingDAYE SPECIAL STEEL CO., LTD. Wuhancarbon, carbon-manganese 190StructuralBarscarbon, carbon-manganese, alloy 190MachineryU1, U2, API-2F 110Chain Cable StockU3, R4 160
As belowB.O.S. / Con CastSteelmakingGUANGXI LIUZHOU GuangzhouA, B 36Normal StrengthPlatesAH27S, AH32, AH36 36Higher StrengthA, B 12Normal StrengthHot Rolled Coil
As below 220B.O.S. / Con CastSteelmakingHEBEI JINGYE CUT DEAL CO. LTD., DalianNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D 30Normal StrengthPlatesAH27S, AH32, AH36, DH32, DH36 30Higher Strength
Pingshan CountyShijiazhuang City
Nandian Town
Tel No +86 311 8287 3953 Fax No +86 311 82873988 Mob +86 158 3111 8888Email [email protected] www.hbjyjt.comCertificate No MD00/4022/0001/1 Expiry Date 09/05/2015
As belowB.O.S. / Con CastSteelmakingHUNAN VALIN LIANYUAN STEEL CO., LTD. Wuhancarbon, carbon-manganese 230SlabsSemi-FinishedA, B, D 25Normal StrengthHot Rolled CoilA, B, D 25Normal StrengthPlates from coils
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished
Jinfeng TownZhangjiagang City
Hongfa Steel PlantSteelmaking Plant Number 1
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: [email protected] Web http://www.sha-steel.comApproval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.Certifcate Number: MD00/3127/0006/1 Expiry date: 28/10/2013
Jiangsu Province 215625
A, B, D, E 60Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH27S,FH32, FH36, FH40
Tel +86 0512 58568791 Fax: +86 0512 58550818 Email: mailto:[email protected] Web: http://www.sha-steel.com Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to60.0mm.Plates in Grades D and E Fine Grain Al+Ti+Nb in the TM+Acc condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to 60.0mm.Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.Certificate No. MD00/3388/0005/1 Expiry date: 28/10/2013
Hongfa Steel PlantSteel Plate Mill LIne No. 2Tel +86 0512 5856 8800 Fax: +86 0512 5855 0818 Email: mailto:[email protected] Web: http://www.sha-steel.com Plates in the Normalizing Rolled are restricted to a maximum width of 4650mm condition and in the TM+Acc condition are restricted to a maximum width of4150mm.Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.Certificate No. MD00/3913/0003/1 Expiry date: 25/05/2014
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished
Hongfa Steel PlantSteelmaking Plant Number 2
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: [email protected] Web http://www.sha-steel.comApproval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.Certifcate Number: MD00/3127/0005/1 Expiry date: 24/05/2014
Jiangsu Province 215625
As belowE.A.F. / IngotSteelmakingJIANGSU SUNAN SPECIAL EQUIPMENT GROUPCO., LTD.
Tel: +86 512 5263 1888 / 1908 Fax: +86 512 5263 7910 email: [email protected] Web: http://snzbjt.comIngots as semi finished products nominal 1170/1290mm diameter x nominal 3000mm long to the above maximum weight are approved for further processingfor forgingsCertificate Number: MD00/3583/0002/1 Expiry: 01/11/2012
JIANGSU
A, B 30Normal StrengthSectionsJIANGYIN BOFENG IRON & STEEL CO., LTD. JiangyinAH27S, AH32 30Higher Strength
Huaxicun Industrial ZoneJiangyin City
Tel: +86 510 8621 7672 Fax: +86 510 8621 7672 Email: [email protected] Web: http://www.bofengsteel.cnThe approved sections are in the form of universal flats nominal widths <600mm to the maximum thickness shown above.Certificate Number: MD00/4031/0001/1 Expiry: 06/06/2015
Jiangsu Province
A, B 25Normal StrengthPlatesJIANGYIN CHANGDA STEEL CO., LTD. JiangyinNo. 388, West Binjiang Road,Jiangyin City,
Tel: +86 510 8603 2250 Fax: +86 510-8603 2250 Email: [email protected] Web: http:// www.chdsteel.comPlates are restricted to a maximum width of 2200mm.Certificate Number: MD00/3975/0001/1 Expiry date: 03/11/2014
Jiangsu Province, 214442,
As belowE.A.F. / IngotSteelmakingJIANGYIN HUAQIANG SPECIAL STEEL Jiangyincarbon, carbon-manganese, alloy 32IngotsSemi-Finished
No. 18, Biangang Road,Huaxi, Jiangyin City,
CASTING & FORGING THERMOELECTRIC CO., LTD.
Tel: +86 510 860 60566 Fax: +86 510 860 60512 Email: [email protected] Web: http://www.jyhuaqing.comIngots as semi finished products nominal 1240mm/1320mm diameter x 2770mm long to the above maximum weight are approved for further processing forforgings.Certificate Number: MD00/4013/0001/1 Expiry: 23/04/2015
Jiangsu Province, 214421,
As BelowB.O.S./E.A.F./Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office297, Bin Jiang East RoadJiangyin City
Tel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:[email protected] Web: http://www.jyxc.comSlabs as Semi-Finished Products to the above maximum thickness, nominal 2600mm width and nominal 12000mm length are approved for further processing forrolled products.Bars as Semi-Finished Products in the As Cast condition to maximum diameter as stated grades are accepted for further processing for forgings.Alloy Grade Bars as Semi-Finished Products in the As Rolled condition to maximum diameter of 280mm are accepted for further processing for forgings.Alloy grade bars as Semi-finished Products are accepted for approved applications, Grade 34Mn2V to 230mm maximum diameter for further processing for gascylinders (Normalised heat treatment required), Grade 42CrMo to 300mm maximum diameter for further processing for marine structural applications(Quenched and Tempered heat treatment required).Bars for mooring chain cable grades are supplied to the following specifications;R3 - R30Mn2, R3S - 28MnCrMo, R4 - 22MnCrNiMo.The supply of mooring grade chain cable bars is restricted to the following sizes for the detailed chain manufacturers;Zhenjiang Anchor Chain Factory - Grades R3 and R3S to 105mm diameter, Grade R4 to 160mm diameter.Jiangsu Asian Star Anchor Chain Cable Co. Ltd - Grades R3 and R3S to 160mm diameter, Grade R4 to 135mm diameter.Liawu Steel Zibo Anchor Chain Cable Co. Ltd Qingdao Branch - Grades R3, R3S and R4 to 114mm diameter. Foshan Marine Anchor Chain Ltd - Grade R3S to 130mm diameter.Certificate #: MD00/2306/0013/1 Expiry date: 26/09/2013
Jiangsu province 214429
As belowB.O.S. / Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
Normal strength, Higher Strength 300SlabsSemi-Finished
Tel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:[email protected] Web: http://www.jyxc.comPlates supplied in the Normalizing Rolled condition are restricted to 3100mm width.Z35 designation for through thickness properties may be added to plates supplied in the normalized condition.Slabs as semi finished products are approved for further processing for rolled products, nominal 3200mm wide x 15,000mm long to the maximum thicknessshown above.Certificate Number: MD00/3857/0003/1 Expiry date: 08/11/2013
Jiangsu Province 214429
A, B, D, E 80Normal StrengthPlatesJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
4300 Plate MillTel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:[email protected] Web: http://www.jyxc.comPlates in the Normalizing Rolled and Thermomechanical supply conditions are restricted to 3800mm maximum width. Z35 designation for through thickness properties may be added to all plates in the above supply conditions.Certificate Number: MD00/xxxx/0001/1 Expiry date: 10/01/2015
As belowB.O.S. / Con CastSteelmakingJINAN IRON AND STEEL CO., LTD. Qingdaocarbon, carbon-manganese 270SlabsSemi-FinishedE 50Normal StrengthPlatesA, B, D 60AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH32,FH36, FH40
As belowB.O.S. / Con CastSteelmakingMAANSHAN IRON & STEEL COMPANY LIMITED NanjingA, B 25Normal StrengthPlatesAH32, AH36, DH32, DH36 25Higher Strength360AR, 410AR 25Boiler & Pressure Vessel
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
XieJiaDianLiuhe District
Nanjing Works
Tel: +86 25 570 74341 Fax: +86 25 57793425 EMail mailto:[email protected] Web:http://www.nisco.com.cnPlates with specified through thickness properties may be accepted with the suffix Z35 applied to all approved grades of normal and higher strength steels.Chain cable stock in Grades U2 and U3 is intended for further processing with quenched and tempered heat treatment, bars at 80mm diameter or less areproduced by BOS or EAF steelmaking, bars over 80mm diameter are produced by EAF steelmaking.Billets and blooms as semi finished products to the above maximum thickness, nominal to 480mm width and to nominal 12000mm length are approved forfurther processing for rolled products.Slabs as semi finished products to the above maximum thickness, nominal to 2510mm width and to nominal 4000mm length are approved for further processingfor rolled products.Certificate Number: MD00/1065/0013/1 Expiry date: 12/10/2013
As belowB.O.S. / Con CastSteelmakingRIZHAO STEEL WIRE CO., LTD Qingdaocarbon, carbon-manganese 230SlabsSemi-FinishedA, B 25Normal StrengthHot Rolled CoilA, B 25Normal StrengthPlates from coils
Tel: +86 (0)751 878 5354 Fax: +86 (0)751 878 6066 Email mailto:[email protected] #: MD00/2175/0008/1 Expiry date: 23/11/2012CEV is limited to a maximum of 0.45% for as rolled and nomalised higher strength steels but does not apply to TM steels
Guangdong 512123
As belowB.O.S. / Con CastSteelmakingSHANDONG SHOUGUANG JUNENG SPECIALSTEEL CO, LTD.
As belowB.O.S. / Con CastSteelmakingTIANJIN IRON AND STEEL GROUP CO. LTD. Daliancarbon, carbon-manganese, alloy 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength
Tel: +86 375 811 1230 Fax: +86 375 811 4006Plates with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2044/0008/1 Expiry date: 14/07/2014
A, B, D, E 100Normal StrengthPlatesWUYANG IRON & STEEL COMPANY LTD. WuhanFH32, FH36, FH40 50Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
Tel No. +86 375 8111230 Fax No. +86 375 8114006 Email to: [email protected] with specified through thickness properties in listed grades of normal and higher strength steelsCertificate No. MD00/3714/0002/1 Expiry Date 14/07/2014
Approved for plates with specified through thickness properties (Z35) in all grades up to 50 mm thickness.
Semi-finished products in carbon and carbon-Manganese steels with fine grain: slabs to 1580mm wide to 8000mm long for further processing for rolled products
272 01 Kladno-DrinTel No +420 558 536 065 Fax No. +420 558 534 926Email [email protected] www.trz.czMachinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.Certificate #: MD00/2955/0005/1 Expiry date: 21/02/2015
Prumyslova 1000CZ-739 70 Trinec - Stare MestoTel: +420 558 533 010 Fax: +420 558 533 306 Email: mailto:[email protected] Web hppt://www.trz.czApproval for Slabs as semi finished products are for further processing for rolled products, nominal sizes are 240mm wide x 12000mm long to the abovemaximum thickness.Approval for Bars as semi finished products are for further processing for tube production, nominal length 1200mm to the above maximum diameter.Certificate #: MD00/1562/0006/1 Inspection Due: 13/07/2013
Tel: +42 (0) 596 082 097 or 558 533 897 Fax: +420 558 533 896 Email mailto:[email protected] Web http://www.trz.czThe approved sections are in the form of universal flats nominal widths 150 to 550mm to the maximum thicknesses shown above.Mechanical testing is carried out by approved works TRINECKE ZELEZARNY A.S. Certificate ID No: MD00/1562.Approval covers for heat treatment is carried out by approved works VITKOVICE HEAVY MACHINERY a.s. Parent Company: TRINECKE ZELEZARNY a.s., Prumyslova 1000, CZ-739 70 Trinec-Stare Metso.Certificate ID No : MD00/2020.Certificate No. MD00/3056/0004/1 Expiry date: 14/02/2013
735 93 Bohumín
As belowE.A.F. / IngotSteelmakingVITKOVICE HEAVY MACHINERY a.s. Praguecarbon, carbon-manganese, alloy 80IngotsSemi-Finished
As belowE.A.F. / Con CastSteelmakingOVAKO IMATRA OY AB Turku/Åbocarbon, carbon-manganese, alloy 370BloomsSemi-FinishedAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
A, B, D, E 15Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
15Higher Strength
Rautaruukintie 155, PO Box 9392101 Raahe
Raahe Steel Works
Tel +358 20 5911 Mob +358 40 54 90257 Fax +358 20 5923527 Email:mailto:[email protected] Web: http://www.ruukki.com Specified through thickness properties for up to 100 mm thickness.
Avenue Jean Jaurès58160 IMPHY*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) for approved applications.Tel: +33 3 86 21 31 23 Fax: +33 3 86 21 31 07 Email:mailto:[email protected] Web:http://www.imphyalloys.com
As belowE.A.F./Ingot/Con CastSteelmakingASCOMETAL Dunkerquecarbon, carbon-manganese, alloy 400Blooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 310StructuralBarscarbon, carbon-manganese, alloy 310MachineryU3 105Chain Cable StockU1, U2 130
59941 DunkerqueCedex 2
Usine de DunesBP 41
Machinery grades up to 180 mm by continuous casting, 310 mm by ingotTel +33 32829 6203 Fax +33 32829 6003Certificate #: MD00/0117/0006/1 Expiry date: 13/09/2012
Including plates with specified through thickness properties.Certificate #: MD00/0351/0006/1 Expiry date: 20/04/2014
As belowE.A.F. / IngotSteelmakingINDUSTEEL FRANCE, site du Creusot Lyoncarbon, carbon-manganese, alloy, austeniticstainless
40IngotsSemi-Finished
71201 71201 LE CRUUSOT CEDEXLe Creusot Cedex
Porte du Breuil - BP 34
Tel No 33 3 8580 5575 Fax No. 33 3 8580 5211Email: [email protected]: www.industeel.infoCertificate number MD00/3227/0001/1Ingots also in martensitic stainless steel up to 40 T for approved applications
A, B, D, E 150Normal StrengthPlatesINDUSTEEL FRANCE, site du Creusot LyonFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 150360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni
Tel +49 3364 3782 05 Fax +49 3364 3781 97 Email: mailto:[email protected] Web http://www.arcelormittal-ehst.comContinuously cast slab up to 250 mm thickness and cast bloom up to 300 mm thickness.Certificate No. MD00/0450/0005/1 Expiry date: 22/01/2013
As belowB.O.S. / Con CastSteelmakingARCELORMITTALAL RUHRORT GmbH Dortmundcarbon, carbon-manganese, alloy 385BloomsSemi-Finishedcarbon, carbon-manganese, alloy 130Billets
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR OfficeNiederdarmer Straße 5D-49811 LingenTel: +49 591 80004 800 Fax: +49 591 80004 460 Email to: [email protected] Web: http://www.benteler.deCertificate No. MD00/1805/0006/1 Expiry date: 11/10/2014
Steelmaking and semi-finished slabs, blooms and billets intended for plates, forgings and tubes.Semi-finished products in carbon, carbon-manganese and alloy steel: slabs to 670mm wide, to 11,500mm long to 12.8 tonnes and blooms/billets of dimensions300mm x 230mm or 310mm round of maximum length 12,800mm
Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength, boiler and pressure vessel grades andferritic steels for low temperature service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The finalprocessing mill is responsible for ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanicalproperties.
A, B, D, E 50Normal StrengthPlatesSALZGITTER MANNESMANN GROBBLECH GmbH DortmundAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
As belowE.A.F. / Con CastSteelmakingESSAR STEEL INDIA LTD. MumbaiNormal strength, Higher Strength 260SlabsSemi-FinishedA, B 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360FG, 410FG 20Boiler & Pressure VesselA, B 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength
Hazira - 394270District Surat
Hot Strip Mill
Tel: +91 261 6683139 Fax: +91 261 6683747 Email mailto:[email protected] Web http://www.essar.com Slabs as semi finished products nominal maximum width 2040mm x nominal maximum length 4900mm to the above maximum thickness are approved forfurther processing for rolled products.Certificate No. MD00/2091/0008/1 Expiry date: 06/06/2015
Gujarat
A, B, D 70Normal StrengthPlatesESSAR STEEL INDIA LTD. MumbaiAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength
Plate Mill DivisionTel: +91 261 668 3291 or 6739 Fax: +91 261 668 3747 Email mailto:[email protected] or [email protected] Webhttp://www.essar.com All plates are restricted to a maximum width of 4550mm.Certificate Number: MD00/3979/002/1 Expiry: 17/01/2015
As belowE.A.F./A.O.D./Con CastSteelmakingFACOR STEELS LTD New Delhiaustenitic stainless, duplex stainlessB.O.S/V.O.D./Con Cast11CrMo91 45Boiler & Pressure VesselsBars13CrMo45 50410AR, 460AR, 490 63304L, 316L 100Austenitic StainlessUNS S31803 122Duplex StainlessU3 56Chain Cable StockU1, U2 80
MIDC Hingna Industrial Estate,Nagpur
Tel No . +91 7104 235701-5 Fax No. +91 7104 235709Email info@{facorsteels.comWeb site: www.facorsteel.comCertificate No MD00/3786/0001/1 Expiry date 18/05/2013
As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. BhilaiA, B, D 75Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. CalcuttaA, B 52Normal StrengthPlates360, 410, 360FG, 410FG 35Boiler & Pressure Vessel360AR, 410AR 40
Tel: +91 2525 261514 Fax: +91 2525 260159 Email mailto:[email protected] Web: http://www.viraj.comBillets and blooms as semi-finished products to the above maximum thickness, nominal 300mm wide x nominal 9000mm long are approved for furtherprocessing for forged products.Certificate Number: MD00/2935/0004/1 Expiry date: 08/12/2014
A, B, D 50Normal StrengthPlatesWelspun Corp Limited MumbaiAH27S, AH32, DH27S, DH32 25Higher Strength460FG, 490FG 25Boiler & Pressure Vessel360FG, 410FG 35
Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemicalcomposition and enables them to achieve the required mechanical propertiesTel +39 432 706922 Fax +39 432 706920 Email:mailto:[email protected] www.cividalespa.comCertificate No. MD00/3149/0002/1 Expiry date: 04/04/2011
Tel: +39 0444 968211 Fax: +39 0444 968182 Email:mailto:[email protected] Web:http://www.acciaierie-valbruna.com* Accepted for approved applicationsApproval for Precipitation Hardened Stainless Machinery Bar is for Grade 17.4 PH, approval for Martensitic Stainless Machinery Bar is for Grade 431 and Grade1.4418 Quenched and Tempered.Duplex Stainless Steel bars are not approved for use in welded construction, and weld repair is not permitted.Approval of Con cast material is for the production of Austenitic Stainless Steels only.Ingots as semi finished products nominal maximum dimensions 600mm x 530mm x 2060mm to the above maximum weight are accepted for further processingfor rolled products and forgings.Billets as semi finished products nominal maximum width 220mm x nominal maximum length 6500mm to the above maximum thickness are accepted forfurther processing for rolled products and forgings.Certificate No. MD00/0041/0006/1 Expiry date: 02/06/2014
As belowE.A.F. / IngotSteelmakingNLMK VERONA Venicecarbon, carbon-manganese 32IngotsSemi-Finished
Via A, Salieri, 22,37050 Vallese di Oppeano (Verona)Tel: +39 045 699 7900 Fax: +39 045 699 7901 email: [email protected] Web: http://www.eu.nlmk.com/verona/Ingots as semi finished products are approved for further processing for forgings to the above maximum weight. Round and Polygon ingots to nominalmaximum dimensions of 1200mm diameter x 4750mm length, oblong ingots to nominal maximum dimensions 970mm x 870mm x 2050mm.Certificate Number MD00/3985/0001/1 Expiry date: 31/01/2015
A, B, D, E 50Normal StrengthFabricated SectionsOFFICINE NORD EST S.r.l TriesteAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
Via Ungaresca No.1233080 San Quirino (Pn)Tel: +39 (0)434 919091 Fax: +39 (0)434 918646 Email to: [email protected] Certificate No. MD00/2626/0006/1 Expiry date: 07/12/2014
As belowE.A.F. / IngotSteelmakingASIA SPECIAL STEEL CO. LTD. Nagasakicarbon, carbon-manganese, alloy 48IngotsSemi-Finished
43-1 Koyomachi, Wakamatsu-ku,Kitakyushu, Fukuoka 808-0002,Tel: +93 482 2222 Fax: +93 482 2227 Email: [email protected] Web: www.asiass.co,jpSemi finished products as ingots, nominal 1600mm diameter x 3100mm high to maximum weight shown above, are approved for further processing forgings.The scope of approval also includes for the provision of molten steel for production of steel castings to Kotobuki Industries Co. Ltd. Kitakyushu Works (LRPlant Reference M3800).Certifcate Number: MN00/3796/0003/1 Expiry date: 29/06/2013
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
1280, HosoeShikama-ku
Himeji Works
Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:[email protected] Internet http://www.jfe-bs.co.jpCertificate No. MD00/1535/0006/1 Expiry date: 27/08/2012
Himeji 672-8064
As belowE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION Yokohamacarbon, carbon-manganese 150BilletsSemi-FinishedA 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher Strength
Ibaraki Pref.314-0111
Kashima Works7 Minamihama, Kamisu-city
Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201 Email: mailto:[email protected] finished products as billets to nominal 150mm width and 12000mm nominal length to the maximum thickness shown above are approved for furtherprocessing for rolled products.Certificate No. MD00/1920/0005/1 Expiry date: 29/01/2014
tel: +81 (0) 242 75 3111 Fax: +81 (0) 242 75 2619 Email mail to: [email protected] or [email protected] Web:http://www.mitsubishisteel.co.jpIngots nominal 2050mm diameter x nominal 1250mm length to the above maximum weight are approved for further processing forgings.Certificate Number: MD00/1802/0001/1 Expiry: 03/03/2015
Fukushima Pref. 969-3471
as below 20IngotsSemi-FinishedMITSUBISHI STEEL MURORAN INC. YokohamaAs below 515Blooms/Billetscarbon, carbon-manganese, alloy 270StructuralBarscarbon, carbon-manganese, alloy 210Machinery
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Kimitsu-shiChiba-ken
Kimitsu Works1 Kimitsu
Materials Quality Scheme approved - MQS001
Materials Quality Scheme covers Steelmaking and rolled plates only. Strip, plate cut from coil and sections approved under Materials Survey Scheme (directsurvey).
All plate grades with specified through thickness properties.Tapered plates in transverse and longditudinal directions.
High strength fine grained Ti+Nb steel plates produced in the TM + Acc and TM + Acc + Temper conditions up to 70mm thickness are approved with Mn andAl contents to be outside that given in Lloyd's Register Materials Rules. Letter 'S' is used after identification number of non-standard composition materials.
Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783 Email: maruyama.kenichi.nsc.co.jp Web: http://www.nsc.co.jp/muroranThe approval for bars intended for chain cable stock are for material rolled from continuous casting billets only.Bars for mooring grade chain cable stock in grades R3, R3S and R4 are restricted to Hamanaka Chain Mfg. Co. Ltd. Himeji plant only.Bars in Grade U3 in the above supply condition may be accepted up to 200mm diameter for the further processing for the production of forged chain cablefittings.Approval for billets, maximum 190mm x 190mm x 8000mm maximum weight 2.3 Tonnes, as semi finished products are for further processing for forgings.Certificate Number: MD00/1101/0011/1 Expiry date: 02/07/2014
050-8550
As belowB.O.S./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Tel +81 97 553 2122 Fax +81 97 553 2379 Email: mailto:[email protected] Web http://www.nsc.co.jp/oita/All plates with specified through thickness properties except H47 grades.* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.* Plates in EH40S are for approved applications only and may have a Nickel content up to 1.5% with a carbon equivalent of 0.4%. The Approved thicknessrange of EH40S is 30mm to 60mm.* Plates in the H47 grades to be produced to the agreed chemistry ranges and agreed max CEVs.
SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested inaccordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not implyconcessions on either design or survey requirements.
SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC conditionup to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on eitherdesign or survey requirements.
SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does notimply concessions on either design or survey requirements.(Note CRL = Corrosion Ratio by Long term test)Certificate No. MD00/1454/0016/1 Expiry date: 09/07/2013
314-0014
A 240Normal StrengthBarsNIPPON STEEL & SUMITOMO METALCORPORATION
As belowE.A.F. / IngotSteelmakingHAMSCO CO., LTD. Changwoncarbon, carbon-manganese, alloy 80IngotsSemi-Finished
San 93, Mokhyun-ri, Hyuchun-myunHamyang-kun
Tel: +82 55 964 8000 Fax: +82 55 964 8011 Mail to: [email protected] No. MD00/3872/0001/1 Expiry date: 05/01/2014
Kyungnam
As belowE.A.F./Ingot/Con CastSteelmakingHYUNDAI STEEL COMPANY Seoulcarbon, carbon-manganese, alloy 75IngotsSemi-Finishedcarbon, carbon-manganese 270Bloomscarbon, carbon-manganese 200BilletsA, B 32Normal StrengthSectionsAH27S, AH32, AH36 32Higher Strength
#1, Songhyun-DongDong-Ku
Inchon Plant
Tel: +82 32 760 2753 Fax: +82 32 760 2866 Email: [email protected] Web: http://www.hyundai-steel.comSections include flat bars up to 400 mm width.Approval for Ingots as Semi-finished Products, Ingots, is for further processing as Forgings.Blooms and Billets as semi finished products are approved for further processing for rolled products to maximum thickness shown above, to nominal width400mm for blooms, 200mm for billets and nominal 10000mm length.Certificate No. MD00/0754/0007/1 Expiry date: 03/01/2014
Inchon
As belowE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY Ulsancarbon, carbon-manganese, alloyBlooms/BilletsSemi-FinishedB, D, E 18Normal StrengthSectionsA 37AH27S, AH40, DH27S, DH40, EH27S, EH32,EH36, EH40, FH27S, FH32, FH36, FH40
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As BelowB.O.S./E.A.F./Con CastSteelmakingHYUNDAI STEEL COMPANY SeoulNormal strength, Higher Strength 300SlabsSemi-FinishedA, B 22Normal StrengthHot Rolled CoilAH32, AH36 22Higher StrengthA, B 22Normal StrengthPlates from coilsAH32, AH36 22Higher Strength
Songak-MyeonDangjin-Gun
HR Coil PlantKodae-Ri
Tel: +82 41 680 1691 Fax +82 41 680 1699 Email; [email protected] Web: http://www.hyundai-steel.comSlabs as semi finished products nominal 2200mm width x nominal 4400mm length are approved for further processing for rolled products, to the abovemaximum thickness produced by B.O.S Steelmaking and to 210mm maximum thickness produced by E.A.F. Steelmaking.Certificate No. MD00/3446/0003/1 Expiry date: 24/03/2014
Chungnam
A, B, D, E 83Normal StrengthPlatesHYUNDAI STEEL COMPANY SeoulFH32, FH36 40Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
Dangjin Works167-32, Godae-RiTel: +82 41 680 1680 or 1685 Fax +82 41 680 1699 Email; [email protected] or [email protected] Web: http://www.hyundai-steel.comApproval is restricted to plates produced with steel made by the BOF + con cast processing route.Approval for plates in grades AH27S, AH32, AH36, 360AR, 410AR, and 460AR as rolled fine grain Al+V are restricted to the thickness range 20.0mm to35.0mm.Approval for plates in grades AH27S, AH32, AH36, AH40, DH27S, DH32, DH36, DH40, EH27S, EH32, EH36, EH40 for the TM+Acc fine grain Al+Nb+Tisupply condition are restricted to the thickness range >15.0mm to 83.0mm.Approval for plates in grades LTDH27S, LTDH32, LTDH36, LTFH27S, LTFH32, LTFH36 for the TM+Acc fine grain Al+Nb+Ti supply condition are restricted tothe thickness range >15.0mm to 40.0mm.Approval for plates in Normalising Rolled condition are restricted to maximum 3200mm width.Plates with specified through thickness properties may be accepted with the suffix Z35 applied to Higher Strength Grades in the TM+acc Fine Grain Al+Nb+Tisupply condition and TM Fine Grain Al+Nb+Ti supply condition .Certificate Number: MD00/3761/0007/1 Expiry: 25/03/2013
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
austenitic stainless 85MachineryBarsKWANG JIN IND CO. LTD. Busan Portalloy 93carbon, carbon-manganese 100
307-103 Shinpyeong-dong,Saha-gu,
Tel No: +82 51 204 9101 Fax No. +82 51 204 9109Email: [email protected] Address www.kjsteel.co.krCert No MD00/3758/0001/1 Expiry date 15.03.2013
Busan,604-030
As belowB.O.S. / Con CastSteelmakingPOSCO Gwangyang Works ChangwonNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG
35Boiler & Pressure Vessel
A, B, D 22Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 12Higher Strength360AR, 410AR 12Boiler & Pressure Vessel
700 Kumho-dongKwangyang-si
Tel: +82 61 790 2170 Fax: +82 61 790 2909 Email: mailto:[email protected] Web: http://www.posco.comThe supply of semi-finished products, slabs, nominal 1750mm wide x 6000mm long x 20 tonnes, for supply for further processing for rolled products.Hot rolled coils in normal strength grades in the supply condition thermomechanical fine grain aluminium are restricted to the thickness ranges >12 to 22mm.Certificate Number: MD00/3086/0008/1 Expiry: 14/07/2014
Cheonnam 545-711
As BelowB.O.S./E.A.F./Con CastSteelmakingPOSCO Pohang Works UlsanA, B, D, E 100Normal StrengthPlatesAH46S*, DH46S*, EH46S* 80Higher StrengthFH27S, FH32, FH36 83AH40, DH40, EH40 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
As belowE.A.F. / IngotSteelmakingSPP YULCHON ENERGY CO., LTD. Mokpocarbon, carbon-manganese, alloy 50IngotsSemi-Finished
Block 8, Yulchon Industrial Complex l, Sinseong-riHaeryong-myeon, Suncheon City, Jeollanam-do
Tel: +82 61 760 7100 Fax: +82 61 725 7733 Email: [email protected] Web: http://www.sppycenergy.co.krIngots as semi finished products are approved for further processing for forgings, nominal maximum dimensions 1630/1850mm diameter x 2850mm long, to theabove maximum weight. Certificate Number: MD00/3866/0001/1 Expiry date: 21/02/2015
Tel: +82 63 460 8222 Fax: +82 63 460 8099 Email: mailto:[email protected] Web:http://www.egs.seah.co.krApproval for Chain Cable Stock Grades R3, R3S, R4, R4S and R5 is restricted to supply to DAI HAN ANCHOR CHAIN MFG CO. LTD and Grades R3, R3Sand R4 to Pu Sung Metal Co., Ltd.Semi Finished Products - Ingots, Carbon & Carbon-manganese nominal sizes 2100 / 2350mm diameter x 2800mm long, and Alloy nominal sizes 2350 / 2600mmdiameter x 3050mm long, to the above maximum weight approved for further processing for forgings. Semi Finished Products - Blooms to nominal 390mm width x 5400mm length, to above maximum thickness approved for further processing for Forgings andRolled Products. Semi Finished Products - Billets to nominal 180 width x 11500mm length, to above maximum thickness approved for further processing for Rolled ProductsCertificate No. MD00/1749/0012/1 Expiry date: 04/04/2015
As belowB.O.S. / Con CastSteelmakingYK STEEL CORP. Busan PortA 7Normal StrengthSectionsA 32Normal StrengthBars
As belowE.A.F. / Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonA, B 26Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
Tel: +389 2 328 7024 Fax: +389 2 3175 982 Email mailto:[email protected] Web http://www.makstil.comSpecified through thickness properties for plates up to 50 mm thicknessCertificate No. MD00/2216/0006/1 Expiry date: 23/05/2013
100-Skopje
Malaysia
A 30Normal StrengthPlatesJI KANG DIMENSI Sdn. Bhd. Kuala Lumpur
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Mexico
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingARCELORMITTAL LAZARO CARDENAS, S.A. deC.V.
Metepec/Veracruz
carbon, carbon-manganese 250SlabsSemi-Finished
60950- Lázaro CárdenasMichoacan
Av Francisco J. Mujica N° 1-B
Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperatureservice according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible forordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties
As belowB.O.S. / Con CastSteelmakingTATA STEEL IJMUIDEN B.V Amsterdamcarbon, carbon-manganese 225SlabsSemi-FinishedA, B 20Normal StrengthPlatesA, B 20Normal StrengthHot Rolled Coil
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 220SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilAH27S, AH32 16Higher StrengthA, B, D 15Normal StrengthPlates from coilsAH27S, AH32 16Higher Strength410 FG, 360 FG, 460 FG 16Boiler and Pressure Vessel
30-969 Kraków
ODDZIAL W KRAKOWIEul. Ujastek 1
Tel: +48 12 293 2104 Fax: +48 12 293 2145 email: [email protected] Web: http://www.arcelormittal.com/poland/Slabs as semi finished products are approved for further processing for rolled products to the maximum thickness shown above and nominal 1580mm widthand 11000mm length.Coils and plates are approved to maximum 2100mm width.Certificate #: MD00/0707/0010/1 Expiry date: 27/01/2014
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 300SlabsSemi-Finishedcarbon, carbon-manganese, Alloy 280Blooms/BilletsB, D, E 15Normal StrengthSectionsA 20
41-308 Dabrowa Gornicza
Oddzial w Dabrowie GorniczejAl. J. Pilsudskiego 92
Tel: +48 32 776 87 14 Fax: +48 32 776 84 86 Email [email protected] Web: http://www.arcelormitta.com/poland/Approved for ingots, and continuously cast products for re- rolling in all the normal and higher tensile strength grades.Certificate No. MD00/0717/0010/1 Expiry date: 06/02/2015
As belowE.A.F./Ingot/Con CastSteelmakingARCELORMITTAL WARSZAWA Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 25IngotsSemi-Finishedcarbon, carbon-manganese, alloy 220Blooms/Billetscarbon, carbon-manganese, alloy 65StructuralBarscarbon, carbon-manganese, alloy 65Machinery
As belowE.A.F. / Con CastSteelmakingFERROSTAL LABEDY Sp. z o.o. Katowicecarbon, carbon-manganese, alloy 160BilletsSemi-Finishedcarbon, carbon-manganese, alloy 170Bars
ul. Zawadzkiego 4744-109 GliwiceTel: +48 32 234 7600 Fax: +48 32 234 7650 EMail mailto:[email protected] Web page http://www.ferrostal.com.plThe semi finished products above are approved for use for further processing for the finished products defined above.Certificate No. MD00/2307/0005/1 Expiry date: 31/03/2014
Tel: +40 236 802100 Fax: +40 236 802101 Email: mailto:[email protected] Web page http://www.arcelormittal.comApproval includes for plates with specified through thickness properties, designation Z25, in all grades up to 60 mm thickness in the normalized condition.Certificate No. MD00/0333/0007/1 Expiry date: 04/12/2013
Tel: +7 8202 531146 Fax: +7 8202 53 2424 EMail: mailto:[email protected] Web http://www.severstal.ruPlates in the As Rolled, Normalized, Quenched and Tempered conditions with specified through thickness properties.Plates in the Normalizing rolled condition to 2200mm maximum width.Certificate #: MD00/0298/00076/1 Expiry date : 14/06/2013
Vologoda Region
A 15Normal StrengthPlatesJ.S.C. SEVERSTAL St. PetersburgA, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
As belowB.O.S. / Con CastSteelmakingOJSC "Magnitogorsk Iron & Steel Works" St. Petersburgcarbon, carbon-manganese 250SlabsSemi-Finished
93, Kirova Street455002 Magnitogorsk
Steel Making and Central Laboratory
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruApproval covers for slabs as detailed above to nominal width 2520mm and nominal length 7000mm for further processing for rolled products.Certificate No. MD00/3103/0003/1 Expiry date: 27/08/2013
A 10Normal StrengthHot Rolled CoilOJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 50Normal StrengthPlatesOJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 40Boiler & Pressure Vessel
Rolling Mill 4500Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruApproval covers for plates in the thickness range 30.0 to 50.0mm, to the maximum thickness shown above.Certificate No. MD00/3837/0001/1 Expiry date: 27/08/2013
As belowB.O.S. / Con CastSteelmakingOJSK Novolipetsk Iron & Steel Corporation MoscowAs below 260SlabsSemi-FinishedA, B, D 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH36, EH40
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingOSKOL St. Petersburgcarbon, carbon-manganese 360BloomsSemi-FinishedU1, U2, U3 80Chain Cable StockBars
Belgorod Region
ELECTROMETALLURGICAL KOMBINAT309515 Stary Oskol-15
Tel +07 4725 375364 Fax +07 4725 373755 [email protected] Web http://www.oemk.ruCertificate No. MD00/3065/0004/1 Expiry date: 26/02/2013
As belowO H / IngotSteelmakingURAL STEEL Open Joint-Stock Company St. PetersburgAs belowE.A.F./Ingot/Con CastB, D 40Normal StrengthPlatesA 50AH32, AH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel
As belowB.O.S. / Con CastSteelmakingU.S. STEEL SERBIA d.o.o. BeogradAs below 200SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilA, B, D 15Normal StrengthPlates from coils
Semi-finished products in carbon and carbon-manganese steels in all normal strength grades and higher tensile strength grades up to EH36 with maximumdimensions 1540mm wide to 12000mm long and thickness as stated.
As BelowB.O.S./E.A.F./Con CastSteelmakingARCELORMITTAL SOUTH AFRICA LTD. JohannesburgAs below 240SlabsSemi-FinishedB, D, E 30Normal StrengthPlatesA 50AH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36
Specified through thickness properties for plates up to 50mm thickness.Tel: +34 985 187299 Fax +34 985 187 519Email: mailto:[email protected] Web page http://www.arcelormittal.comCertificate No. MD00/1804/0008/1 Expiry date: 25/09/2014
As belowE.A.F. / Con CastSteelmakingCOMPAÑÍA ESPAÑOLA DE LAMINACIÓN, S.L. BarcelonaA 180BilletsSemi-FinishedA 50Normal StrengthSectionsA 35Normal StrengthBars
08755Castellbisbal (Barcelona)
Poligono Industrial 'San Vicente' s/n
Tel: +34 630 970 990 Fax: +34 93 773 0552 Email:mailto:[email protected] Web:http://www.celsa.comApproved for the supply of continuously cast billets up to 180 x 180 mm.Certificate No. MD00/0343/0007/1 Expiry date: 22/03/2013
Steel types carbon and carbon-manganese cover the supply of billets for processing into normal strength steels according to the Society's Rules for theManufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for ordering steel which complies with their approvedchemical composition and enables them to achieve the required mechanical properties
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingGERDAU ACEROS ESPECIALES EUROPA S.L.(GERDAU)
Bilbao
As below 300BloomsSemi-Finished
carbon, carbon-manganese, alloy 100MachineryBars
R3, R3S, R4, API-2F, R5 78Chain Cable Stock
U2, U3 100
Bo. Ugarte, S/NP.O. Box 76
Planta Basauri
Tel +34 944 871 726 Fax +34 944 871826 Email: mailto:[email protected]: www.gerdau.esThe approval for bars for chain cable stock grades R3 and R3S are restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R3-R3S.The approval for bars for chain cable stock grade R4 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R4.The approval for bars for chain cable stock grade R5 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R5.The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.Certificate No. MD00/0051/0008/1 Expiry date: 22/01/2015
48970 Basauri (Vizcaya)
carbon, carbon-manganese, alloy 37StructuralBarsGERDAU ACEROS ESPECIALES EUROPA S.L.(GERDAU)
Paseo Alejandro Calonje, 139200 Reinosa (Cantabria)Tel: +34 942 775 187 Fax: +34 942 775 283 Email: mailto:[email protected] Web http://www.sidenor.comThe approval for bars for chain cable stock grades R3 and R3S are restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R3-R3S.The approval for bars for chain cable stock grades R4 and R5* are restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R4S.The approval for bars for chain cable stock in Grade R4 to 130mm diameter manufactured by con cast steelmaking at Fabrica de Basauri, rolling at AzkoitaPlant, finishing at Reinosa are restricted for supply to Vicinay Cadenas S.A. to purchasing specification MP-R4S. The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.Certificate No. MD00/0546/0010/1 Expiry date: 20/06/2014
A, B, D, E 25Normal StrengthFabricated SectionsHIERROS MARCELINO FRANCO S.A. GijonAH32, AH36, DH32, DH36, EH32, EH36 25Higher Strength
Tel: +34 943 857311 Fax: +34 943 857312 Email: mailto:[email protected] Web http://www.rugui.comThe approved sections are in the form of flat bars up to a width of 150mm. Certificate No. MD00/1915/0005/1 Expiry date: 06/02/2014
Tel: +34 943 025206 Fax: +34 943 025299 Email: mailto:[email protected] The approval for bars for chain cable stock grades R3 and R3S are restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R3-R3S.The approval for bars for chain cable stock grade R4 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R4.The approval for bars for chain cable stock grade R5 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R5, this approval is withbars rolled from steel made at Sidenor Industrial S.L. Fabrica de Basauri plant. The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.
Raw materials ingot and bloom are sourced from Basauri and Reinosa Plants and no longer produce steel.Web:http//:www:gerdau.esCertificate No. MD00/0620/0009/1 Expiry date: 27/03/2014
Semi Finished products austenitic and duplex stainless steel con-cast Blooms to 365mm wide, to 7500mm long; Con-cast Billets to 150mm wide, to 6200mm long;As rolled billets to 195mm wide, to 6000mm long; semi-finished as rolled bars to 185mm diameter, 6900mm long for further processing for Rolled, ForgedProducts
As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS AB Stockholm304L, 304LN, 316L, 321, 347 12Austenitic StainlessPlatesUNS S31803, UNS 32205* 8Duplex Stainless304L, 316L, 321, 347 8Austenitic StainlessHot Rolled Coil
Tel: 46 586 47000 Fax: 46 586 47019 Email: mailto:[email protected] Web: http://www.outokumpu.com* accepted for approved applications** Grade UNS 32304 may be accepted as equivalent to 316L as shown in LR Rules when properties meet the Rule requirements.
Certificate Number MD00/1754/0006/1 Expiry date: 14/11/2014
UNS S31803, UNS S32205* 200Duplex StainlessBarsOUTOKUMPU STAINLESS AB Kristinehamn
SE-693 81 DegerforsDegerfors Stainless
Tel: +46 (0)586 47000/47 232 Fax: +46 (0)586 47008Email mailto:[email protected] Web http://www.outokumpu.comEN 10088-1 grade 1.4462 accepted for approved applications only.Certificate number MD00/3144/0004/1 Expiry date: 08/06/2014
Tel +46 155 254783 Fax +46 155 254082 Email: mailto:[email protected] Web:http://www.ssab.comAll plates with specified through thickness properties.Semi-finished products in carbon and carbon-manganese steel with fine grain (element combinations as stated), slabs to 1680 mm wide, to 11000mm long ofmaximum weight 30T for further processing to rolled productsMaterials Quality Scheme Approved - Approval No. MQS 049Certificate No. MD00/1282/0009/1 Expiry date: 25/04/2013
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Turkey
As belowE.A.F./Ingot/Con CastSteelmakingASIL CELIK SANAYI VE TICARET A.S. Istanbulcarbon, carbon-manganese, alloy 300StructuralBarscarbon, carbon-manganese, alloy 220Machinery
As belowE.A.F. / Con CastSteelmakingÖZKAN DEMIR ÇELIK SANAYI A.S. Istanbulcarbon, carbon manganese 260Blooms/BilletsSemi-FinishedD, E 12Normal StrengthSectionsA, B 25AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
As BelowOH/Ingot/ Con CastSteelmakingCJSC DONETSKSTEEL IRON AND STEEL WORKS Mykolaivcarbon, carbon-manganese 5IngotsSemi-Finishedcarbon, carbon-manganese 150Slabs
1 Levchenko StreetMariupol 87504All grades and thicknesses with specified through thickness properties. Notation Z25 or Z35 may be added.Tel: +38 (0)0 629 4343 23 Fax: +38 (0)62 5300 39 Web http://www.ilyich.com.uaCertificate No. MD00/0775/0005/1 Expiry date: 03/07/2013
As belowB.O.S. / IngotSteelmakingPJSC ENAKIEVO IRON AND STEEL WORKS Mykolaivcarbon, carbon-manganese 9IngotsSemi-FinishedA, B 11Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32 11Higher Strength
The approval for steelmaking and ingots, slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitationhardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international ornational standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approvedchemical composition to enables them to achieve the required physical and mechanical properties.
As belowB.O.S. / Con CastSteelmakingTATA STEEL UK LIMITED Liverpoolcarbon, carbon-manganese 238SlabsSemi-Finished
Port TalbotSA13 2NG
Port Talbot Works
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.corusgroup.comApproval covers concast slabs to nominal size 1850mm wide x 10,000mm long to the maximum thickness for further processing to rolled products.
A, B, D 50Normal StrengthPlatesEVRAZ OREGON STEEL MILLS Los AngelesAH27S, AH32, AH36, DH27S, DH32, DH36 12Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG 50
14400 N. Rivergate Blvd.Portland
Tel: +1 503 978 6130 Fax: +1 503 978 4975Email: mailto:[email protected] Web http://www.evrazincna.comIncluding all plate grades and thicknesses with specified through thickness properties (Z35)
Tel: +1 330 438 5541 Fax: +1 330 438 5213 Email: mailto:[email protected] Web: http://www.republicengineered.comIngots as semi finished products, nominal 740mm diameter x 4800mm, are approved for further processing for forgings to the maximum un-cropped weightshown above.Certificate #: MD00/2236/0005/1 Expiry date: 15/05/2013
Ohio 44704-2311
As belowE.A.F. / Con CastSteelmakingSSAB ALABAMA, INC. New OrleansD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
As belowE.A.F./Ingot/Con CastSteelmakingTHE TIMKEN COMPANY STEEL BUSINESS Chicagocarbon, carbon-manganese, alloy 330BarsSemi-Finished
CantonOH 44706-0932
1835 Dueber Avenue S.W.
TTel: +1 330 471 3263 Fax: +1 330 471 4077 Email: mailto:[email protected] Werb: http://www.timken.comBars as Semi Finished Products approved for further processing for forgings and for use as billets for seamless tube production.Certificate No. MD00/1510/0005/1 Expiry date: 12/01/2014