Page 1
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 1/27
List of International Organization forStandardization standards
This is a list of current, published[Note 1] International Or-
ganization for Standardization (ISO) standards and other
deliverables.[Note 2] For a complete and up-to-date list of
all the ISO standards, see the ISO catalogue.[1]
The standards are protected by copyright and most of
them must be purchased. However about 300 of the
standards produced by ISO and IEC's Joint Technical
Committee 1 (JTC1) have been made freely and publicly
available.[2]
This is an incomplete list that may not be able to
satisfy particular standards for completeness.
You can help by expanding it with reliably
sourced entries.
1 ISO 1 – ISO 99
•
ISO 1:2002 Geometrical Product Specifications(GPS) – Standard reference temperature for geo-
metrical product specification and verification
• ISO 2:1973 Textiles – Designation of the direction
of twist in yarns and related products
• ISO 3:1973 Preferred numbers – Series of preferred
numbers
• ISO 4:1997 Information and documentation – Rules
for the abbreviation of title words and titles of pub-
lications
• ISO 5 Photography and graphic technology – Den-
sity measurements
• ISO 5-1:2009 Geometry and functional nota-
tion
• ISO 5-2:2009 Geometric conditions for trans-
mittance density
• ISO 5-3:2009 Spectral conditions
• ISO 5-4:2009 Geometric conditions for reflec-
tion density
• ISO 6:1993 Photography – Black-and-white picto-rial still camera negative film/process systems – De-
termination of ISO speed
• ISO 7 Pipe threads where pressure-tight joints are
made on the threads
• ISO 7-1:1994 Dimensions, tolerances and des-
ignation
• ISO 7-2:2000 Verification by means of limit
gauges
• ISO 8:1977 Documentation – Presentation of peri-
odicals
• ISO 9:1995 Information and documentation –
Transliteration of Cyrillic characters into Latin
characters – Slavic and non-Slavic languages
• ISO 11:1987 Aircraft – Ground pressure testing
connections for pressure cabins
• ISO 12:1987 Aerospace – Pipelines – Identification
• ISO 14:1982 Straight-sided splines for cylindrical
shafts with internal centering – Dimensions, toler-
ances and verification
• ISO 15:2011 Radial bearings -- Boundary dimen-
sions, general plan
• ISO 16:1975 Acoustics – Standard tuning frequency
(Standard musical pitch)
• ISO 17:1973 Guide to the use of preferred numbers
and of series of preferred numbers
• ISO 18:1981 Documentation – Contents list of pe-
riodicals
• ISO 21:1985 Shipbuilding – Inland navigation –
Cable-lifters for stud-link anchor chains
• ISO 22:1991 Belt drives – Flat transmission belts
and corresponding pulleys – Dimensions and toler-
ances
• ISO 23:1993 Cinematography -- Camera usage of
35 mm motion-picture film -- Specifications
• ISO 25:1994 Cinematography -- Camera usage of
16 mm motion-picture film -- Specifications
• ISO 26:1993 Cinematography -- Projector usage of16 mm motion-picture films for direct front projec-
tion -- Specifications
1
Page 2
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 2/27
2 1 ISO 1 – ISO 99
• ISO 28:1976 Cinematography -- Camera usage of 8
mm Type R motion-picture film -- Specifications
• ISO 29:1980 Cinematography -- Projector usage of
8 mm Type R silent motion-picture film for direct
front projection -- Specifications [Withdrawn with-
out replacement]
• ISO 31 Quantities and units [withdrawn: replaced
with ISO/IEC 80000]
• ISO 32:1977 Gas cylinders for medical use -- Mark-
ing for identification of content
• ISO 34
• ISO 34-1:2010 Rubber, vulcanized or thermo-
plastic -- Determination of tear strength -- Part
1: Trouser, angle and crescent test pieces
• ISO 34-2:2011 Rubber, vulcanized or thermo-
plastic -- Determination of tear strength -- Part
2: Small (Delft) test pieces
• ISO 35:2004 Natural rubber latex concentrate -- De-
termination of mechanical stability
• ISO 36:2011 Rubber, vulcanized or thermoplastic --
Determination of adhesion to textile fabrics
• ISO 37:2011 Rubber, vulcanized or thermoplastic
— Determination of tensile stress-strain properties
• ISO 41:1980 Shipbuilding -- Inland vessels -- Cov-
ers for deck openings for pumps [withdrawn withoutreplacement]
• ISO 43:1976 Aircraft -- Jacking pads
• ISO 44:1975 Aerospace -- Lever-operated, two-
position, ON/OFF switches -- Directions of oper-
ation
• ISO 45:1990 Aircraft -- Pressure refuelling connec-
tions
• ISO 46:1973 Aircraft -- Fuel nozzle grounding plugs
and sockets
• ISO 48:2010 Rubber, vulcanized or thermoplastic -
- Determination of hardness (hardness between 10
IRHD and 100 IRHD)
• ISO 49:1994 Malleable cast iron fittings threaded to
ISO 7-1
• ISO 50:1977 Metal pipes -- Steel sockets screwed
according to ISO 7 [Withdrawn without replace-
ment]
• ISO 53:1998 Cylindrical gears for general and heavy
engineering -- Standard basic rack tooth profile
• ISO 54:1996 Cylindrical gears for general engineer-
ing and for heavy engineering -- Modules
• ISO 55:1977 Seedlac -- Specification [Withdrawn
without replacement]
• ISO 57:1975 Bleached lac -- Specification [With-
drawn without replacement]
• ISO 60:1977 Plastics -- Determination of apparent
density of material that can be poured from a spec-
ified funnel
• ISO 61:1976 Plastics -- Determination of apparent
density of moulding material that cannot be poured
from a specified funnel
• ISO 62:2008 Plastics -- Determination of water ab-
sorption
• ISO 63:1975 Flat transmission belts -- Lengths
[Withdrawn: Replaced with ISO 22]
• ISO 65:1981 Carbon steel tubes suitable for screw-
ing in accordance with ISO 7-1
• ISO 67:1981 Muscovite mica blocks, thins and films
-- Grading by size [Withdrawn without replacement]
• ISO 68 ISO general-purpose screw threads – Basic
profile
• ISO 68-1:1998 Metric screw threads
• ISO 68-2:1998 Inch screw threads
• ISO 69:1998 Cinematography -- 16 mm motion-
picture and magnetic film -- Cutting and perforating
dimensions
• ISO 70:1981 Cinematography -- 35 mm nega-
tive photographic sound record on 35 mm motion-
picture film -- Position and maximum width dimen-
sions
• ISO 71:1977 Cinematography -- 16 mm negative
photographic sound record on 16 mm, 35/16 mm
and 35/32 mm motion-picture film -- Positions and
dimensions
• ISO 74:1976 Cinematography -- Image area pro-
duced by camera aperture and maximum pro-
jectable image area on 8 mm Type R motion-picturefilm -- Positions and dimensions
• ISO 75 Plastics -- Determination of temperature of
deflection under load
• ISO 75-1:2013 Plastics -- Determination of
temperature of deflection under load -- Part 1:
General test method
• ISO 75-2:2013 Plastics -- Determination of
temperature of deflection under load -- Part 2:
Plastics and ebonite
• ISO 75-3:2004 Plastics -- Determination of
temperature of deflection under load -- Part3: High-strength thermosetting laminates and
long-fibre-reinforced plastics
Page 3
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 3/27
3
• ISO 76:2006 Rolling bearings -- Static load ratings
• ISO 78 Chemistry — Layouts for standards
• ISO 78-2:1999 Chemistry -- Layouts for stan-
dards -- Part 2: Methods of chemical analysis
•
ISO 78-3:1983 Chemistry -- Layouts for stan-dards -- Part 3: Standard for molecular absorp-
tion spectrometry
• ISO 78-4:1983 Layouts for standards -- Part 4:
Standard for atomic absorption spectrometric
analysis
• ISO 82:1974 Steel -- Tensile testing [Withdrawn:
replaced with ISO 6892-1]
• ISO 83:1976 Steel -- Charpy impact test (U-notch)
[Withdrawn: replaced with ISO 148-1]
• ISO 86:1974 Steel -- Tensile testing of sheet and
strip less than 3 mm and not less than 0,5 mm thick[Withdrawn: replaced with ISO 6892-1]
• ISO 89:1974 Steel -- Tensile testing of wire [With-
drawn: replaced with ISO 6892-1]
• ISO 90 Light gauge metal containers -- Definitions
and determination of dimensions and capacities
• ISO 90-1:1997 Light gauge metal containers -
- Definitions and determination of dimensions
and capacities -- Part 1: Open-top cans
• ISO 90-2:1997 Light gauge metal containers -
- Definitions and determination of dimensionsand capacities -- Part 2: General use contain-
ers
• ISO 90-3:2000 Light gauge metal containers -
- Definitions and determination of dimensions
and capacities -- Part 3: Aerosol cans
• ISO 91 Petroleum measurement tables
• ISO 91-1:1992 Petroleum measurement tables
-- Part 1: Tables based on reference tempera-
tures of 15 degrees C and 60 degrees F
• ISO 91-2:1991 Petroleum measurement tables
-- Part 2: Tables based on a reference temper-ature of 20 degrees C
• ISO 92:1976 Textile machinery and accessories -
- Spinning machinery -- Definition of side (left or
right)
• ISO 93 Textile machinery and accessories -- Cylin-
drical sliver cans
• ISO 93-1:2006 Textile machinery and acces-
sories -- Cylindrical sliver cans -- Part 1: Main
dimensions
• ISO 93-2:2006 Textile machinery and acces-sories -- Cylindrical sliver cans -- Part 2:
Spring bottoms
• ISO 94:1982 Textile machinery and accessories --
Spindle gauges for ring-spinning and ring-doubling
frames
• ISO 96 Textile machinery and accessories -- Rings
and travellers for ring spinning and ring twisting
frames
• ISO 96-1:2009 Textile machinery and acces-
sories -- Rings and travellers for ring spinning
and ring twisting frames -- Part 1: Flange rings
T and SF and their travellers
• ISO 96-2:2009 Textile machinery and acces-
sories -- Rings and travellers for ring spinning
and ring twisting frames -- Part 2: HZ- and
J-rings and their travellers
• ISO 97:1975 Textile machinery and accessories --
Rings for spinning, doubling and twisting for ear-
shaped travellers
• ISO 98:2001 Textile machinery and accessories -
- Spinning preparatory and spinning machinery --
Main dimensions of coverings for top rollers
2 ISO 100 – ISO 199
• ISO 100:1984 Pulleys for flat transmission belts --
Crowns [Withdrawn: replaced with ISO 22]
• ISO 102:1990 Aircraft -- Gravity filling orifices
• ISO 104:2002 Rolling bearings -- Thrust bearings --
Boundary dimensions, general plan
• ISO 105 Textiles — Tests for colour fastness
• ISO 105-A01:2010 Part A01: General princi-
ples of testing
• ISO 105-A02:1993 Part A02: Grey scale for
assessing change in colour
• ISO 105-A03:1993 Part A03: Grey scale for
assessing staining
• ISO 105-A04:1989 Part A04: Method for the
instrumental assessment of the degree of stain-
ing of adjacent fabrics
• ISO 105-A05:1996 Part A05: Instrumental
assessment of change in colour for determina-
tion of grey scale rating
• ISO 105-A06:1995 Part A06: Instrumental
determination of 1/1 standard depth of colour
• ISO 105-A08:2001 Part A08: Vocabulary
used in colour measurement
• ISO 105-A11:2012 Part A11: Determinationof colour fastness grades by digital imaging
techniques
Page 4
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 4/27
4 2 ISO 100 – ISO 199
• ISO 105-B01:1994 Part B01: Colour fastness
to light: Daylight
• ISO 105-B02:2013 Part B02: Colour fastness
to artificial light: Xenon arc fading lamp test
• ISO 105-B03:1994 Part B03: Colour fastness
to weathering: Outdoor exposure• ISO 105-B04:1994 Part B04: Colour fastness
to artificial weathering: Xenon arc fading lamp
test
• ISO 105-B05:1993 Part B05: Detection and
assessment of photochromism
• ISO 105-B06:1998 Part B06: Colour fastness
and ageing to artificial light at high tempera-
tures: Xenon arc fading lamp test
• ISO 105-B07:2009 Part B07: Colour fastness
to light of textiles wetted with artificial perspi-
ration
• ISO 105-B08:1995 Part B08: Quality control
of blue wool reference materials 1 to 7
• ISO 105-B10:2011 Part B10: Artificial weath-
ering -- Exposure to filtered xenon-arc radia-
tion
• ISO 105-C06:2010 Part C06: Colour fastness
to domestic and commercial laundering
• ISO 105-C07:1999 Part C07: Colour fastness
to wet scrubbing of pigment printed textiles
• ISO 105-C08:2010 Part C08: Colour fastness
to domestic and commercial laundering using
a non-phosphate reference detergent incorpo-
rating a low-temperature bleach activator
• ISO 105-C09:2001 Part C09: Colour fastness
to domestic and commercial laundering -- Ox-
idative bleach response using a non-phosphate
reference detergent incorporating a low tem-
perature bleach activator
• ISO 105-C10:2006 Part C10: Colour fastness
to washing with soap or soap and soda
• ISO 105-C12:2004 Part C12: Colour fastness
to industrial laundering
• ISO 105-D01:2010 Part D01: Colour fastness
to drycleaning using perchloroethylene solvent
• ISO 105-D02:1993 Part D02: Colour fastness
to rubbing: Organic solvents
• ISO 105-E01:2013 Part E01: Colour fastness
to water
• ISO 105-E02:2013 Part E02: Colour fastness
to sea water
• ISO 105-E03:2010 Part E03: Colour fastness
to chlorinated water (swimming-pool water)• ISO 105-E04:2013 Part E04: Colour fastness
to perspiration
• ISO 105-E05:2010 Part E05: Colour fastness
to spotting: Acid
• ISO 105-E06:2006 Part E06: Colour fastness
to spotting: Alkali
• ISO 105-E07:2010 Part E07: Colour fastness
to spotting: Water• ISO 105-E08:1994 Part E08: Colour fastness
to hot water
• ISO 105-E09:2010 Part E09: Colour fastness
to potting
• ISO 105-E10:1994 Part E10: Colour fastness
to decatizing
• ISO 105-E11:1994 Part E11: Colour fastness
to steaming
• ISO 105-E12:2010 Part E12: Colour fastness
to milling: Alkaline milling
• ISO 105-E13:1994 Part E13: Colour fastnessto acid-felting: Severe
• ISO 105-E14:1994 Part E14: Colour fastness
to acid-felting: Mild
• ISO 105-E16:2006 Part E16: Colour fastness
to water spotting on upholstery fabrics
• ISO 105-F01:2001 Part F01: Specification for
wool adjacent fabric
• ISO 105-F02:2009 Part F02: Specification for
cotton and viscose adjacent fabrics
• ISO 105-F03:2001 Part F03: Specification for
polyamide adjacent fabric
• ISO 105-F04:2001 Part F04: Specification for
polyester adjacent fabric
• ISO 105-F05:2001 Part F05: Specification for
acrylic adjacent fabric
• ISO 105-F06:2000 Part F06: Specification for
silk adjacent fabric
• ISO 105-F07:2001 Part F07: Specification for
secondary acetate adjacent fabric
• ISO 105-F09:2009 Part F09: Specification for
cotton rubbing cloth
• ISO 105-F10:1989 Part F10: Specification for
adjacent fabric: Multifibre
• ISO 105-G01:1993 Part G01: Colour fastness
to nitrogen oxides
• ISO 105-G02:1993 Part G02: Colour fastness
to burnt-gas fumes
• ISO 105-G03:1993 Part G03: Colour fastness
to ozone in the atmosphere
• ISO 105-G04:1989 Part G04: Colour fastness
to oxides of nitrogen in the atmosphere at high
humidities• ISO 105-J01:1997 Part J01: General princi-
ples for measurement of surface colour
Page 5
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 5/27
5
• ISO 105-J02:1997 Part J02: Instrumental as-
sessment of relative whiteness
• ISO 105-J03:2009 Part J03: Calculation of
colour differences
• ISO 105-J05:2007 Part J05: Method for the
instrumental assessment of the colour incon-stancy of a specimen with change in illuminant
(CMCCON02)
• ISO 105-N01:1993 Part N01: Colour fastness
to bleaching: Hypochlorite
• ISO 105-N02:1993 Part N02: Colour fastness
to bleaching: Peroxide
• ISO 105-N03:1993 Part N03: Colour fastness
to bleaching: Sodium chlorite (mild)
• ISO 105-N04:1993 Part N04: Colour fastness
to bleaching: Sodium chlorite (severe)
• ISO 105-N05:1993 Part N05: Colour fastnessto stoving
• ISO 105-P01:1993 Part P01: Colour fastness
to dry heat (excluding pressing)
• ISO 105-P02:2002 Part P02: Colour fastness
to pleating: Steam pleating
• ISO 105-S01:1993 Part S01: Colour fastness
to vulcanization: Hot air
• ISO 105-S02:1993 Part S02: Colour fastness
to vulcanization: Sulfur monochloride
• ISO 105-S03:1993 Part S03: Colour fastness
to vulcanization: Open steam
• ISO 105-X01:1993 Part X01: Colour fastness
to carbonizing: Aluminium chloride
• ISO 105-X02:1993 Part X02: Colour fastness
to carbonizing: Sulfuric acid
• ISO 105-X04:1994 Part X04: Colour fastness
to mercerizing
• ISO 105-X05:1994 Part X05: Colour fastness
to organic solvents
• ISO 105-X06:1994 Part X06: Colour fastness
to soda boiling
• ISO 105-X07:1994 Part X07: Colour fastness
to cross-dyeing: Wool
• ISO 105-X08:1994 Part X08: Colour fastness
to degumming
• ISO 105-X09:1993 Part X09: Colour fastness
to formaldehyde
• ISO 105-X10:1993 Part X10: Assessment
of migration of textile colours into polyvinyl
chloride coatings
• ISO 105-X11:1994 Part X11: Colour fastness
to hot pressing• ISO 105-X12:2001 Part X12: Colour fastness
to rubbing
• ISO 105-X13:1994 Part X13: Colour fast-
ness of wool dyes to processes using chemical
means for creasing, pleating and setting
• ISO 105-X14:1994 Part X14: Colour fast-
ness to acid chlorination of wool: Sodium
dichloroisocyanurate
• ISO 105-X16:2001 Part X16: Colour fastness
to rubbing -- Small areas
• ISO 105-X18:2007 Part X18: Assessment of
the potential to phenolic yellowing of materials
• ISO 105-Z01:1993 Part Z01: Colour fastness
to metals in the dye-bath: Chromium salts
• ISO 105-Z02:1993 Part Z02: Colour fastness
to metals in the dye-bath: Iron and copper
• ISO 105-Z03:1996 Part Z03: Intercompati-
bility of basic dyes for acrylic fibres
• ISO 105-Z04:1995 Part Z04: Dispersibility ofdisperse dyes
• ISO 105-Z05:1996 Part Z05: Determination
of the dusting behaviour of dyes
• ISO 105-Z06:1998 Part Z06: Evaluation of
dye and pigment migration
• ISO 105-Z07:1995 Part Z07: Determination
of application solubility and solution stability
of water-soluble dyes
• ISO 105-Z08:1995 Part Z08: Determination
of solubility and solution stability of reactive
dyes in the presence of electrolytes
• ISO 105-Z09:1995 Part Z09: Determination
of cold water solubility of water-soluble dyes
• ISO 105-Z10:1997 Part Z10: Determination
of relative colour strength of dyes in solution
• ISO 105-Z11:1998 Part Z11: Evaluation of
speckiness of colorant dispersions
• ISO 108:1976 Textile machinery and accessories --
Weaving looms -- Definition of left and right sides
• ISO 109:1982 Textile machinery -- Working widths
of weaving machines
• ISO 110:1978 Textile machinery and accessories --
Cones for yarn winding (cross wound) -- Half an-
gle of the cone 9 degrees 15' [Withdrawn without
replacement]
• ISO 111:1978 Textile machinery and accessories --
Cones for yarn winding (cross wound) -- Half an-
gle of the cone 4 degrees 20' [Withdrawn: Replaced
with ISO 8489-3]
• ISO 112:1983 Textile machinery and accessories --
Cones for yarn winding (cross wound) -- Half an-gle of the cone 3 degrees 30' [Withdrawn: Replaced
with ISO 8489-2]
Page 6
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 6/27
6 2 ISO 100 – ISO 199
• ISO 113:2010 Rolling bearings -- Plummer block
housings -- Boundary dimensions
• ISO 114:1980 99.8 Unalloyed magnesium ingots -
- Chemical composition [Withdrawn: Replaced by
ISO 8287]
• ISO 115:2003 Unalloyed aluminium ingots for
remelting -- Classification and composition
• ISO 119:1977 Plastics -- Phenol-formaldehyde
mouldings -- Determination of free phenols -- Iodo-
metric method
• ISO 120:1977 Plastics -- Phenol-formaldehyde
mouldings -- Determination of free ammonia and
ammonium compounds -- Colorimetric comparison
method
• ISO 121:1980 Magnesium-aluminium-zinc alloy in-
gots and alloy castings -- Chemical composition and
mechanical properties of sand cast reference test
bars [Withdrawn: replaced by ISO 16220]
• ISO 123:2001 Rubber latex -- Sampling
• ISO 124:2011 Latex, rubber -- Determination of to-
tal solids content
• ISO 125:2011 Natural rubber latex concentrate --
Determination of alkalinity
• ISO 126:2005 Natural rubber latex concentrate --
Determination of dry rubber content
• ISO 127:2012 Rubber, natural latex concentrate --
Determination of KOH number
• ISO 128
• ISO 128-1:2003 Technical drawings -- Gen-
eral principles of presentation -- Part 1: Intro-
duction and index
• ISO 128-15:2013 Technical product docu-
mentation (TPD) -- General principles of pre-
sentation -- Part 15: Presentation of shipbuild-
ing drawings
• ISO 128-20:1996 Technical drawings -- Gen-
eral principles of presentation -- Part 20: Basic
conventions for lines
• ISO 128-21:1997 Technical drawings -- Gen-
eral principles of presentation -- Part 21:
Preparation of lines by CAD systems
• ISO 128-22:1999 Technical drawings -- Gen-
eral principles of presentation -- Part 22: Basic
conventions and applications for leader lines
and reference lines
• ISO 128-23:1999 Technical drawings -- Gen-eral principles of presentation -- Part 23: Lines
on construction drawings
• ISO 128-24:1999 Technical drawings -- Gen-
eral principles of presentation -- Part 24: Lines
on mechanical engineering drawings
• ISO 128-25:1999 Technical drawings -- Gen-
eral principles of presentation -- Part 25: Lines
on shipbuilding drawings
• ISO 128-30:2001 Technical drawings -- Gen-
eral principles of presentation -- Part 30: Basic
conventions for views
• ISO 128-34:2001 Technical drawings -- Gen-
eral principles of presentation -- Part 34:
Views on mechanical engineering drawings
• ISO 128-40:2001 Technical drawings -- Gen-
eral principles of presentation -- Part 40: Basic
conventions for cuts and sections
• ISO 128-44:2001 Technical drawings -- Gen-
eral principles of presentation -- Part 44: Sec-
tions on mechanical engineering drawings
• ISO 128-50:2001 Technical drawings -- Gen-
eral principles of presentation -- Part 50: Basic
conventions for representing areas on cuts and
sections
• ISO/TS 128-71:2010 Technical product docu-
mentation (TPD) -- General principles of pre-
sentation -- Part 71: Simplified representation
for mechanical engineering drawings
• ISO 129
• ISO 129-1:2004 Technical drawings -- Indi-
cation of dimensions and tolerances -- Part 1:
General principles
• ISO 129-4:2013 Technical product documen-
tation (TPD) -- Indication of dimensions and
tolerances -- Part 4: Dimensioning of ship-
building drawings
• ISO 131:1979 Acoustics -- Expression of physical
and subjective magnitudes of sound or noise in air
[Withdrawn without replacement]
• ISO 132:2011 Rubber, vulcanized or thermoplastic
-- Determination of flex cracking and crack growth
(De Mattia)
• ISO 133:1983 Rubber, vulcanized -- Determination
of crack growth (De Mattia) [Withdrawn: Replaced
with ISO 132]
• ISO 136:1972 Steel -- Simple torsion testing of wire
[Withdrawn replaced by ISO 7800]
• ISO 137:1975 Wool -- Determination of fibre diam-
eter -- Projection microscope method
• ISO 139:2005 Textiles -- Standard atmospheres for
conditioning and testing
• ISO 140 Acoustics -- Measurement of sound insula-
tion in buildings and of building elements
Page 7
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 7/27
7
• ISO 140-2:1991 Part 2: Determination, veri-
fication and application of precision data
• ISO 140-4:1998 Part 4: Field measurements
of airborne sound insulation between rooms
• ISO 140-5:1998 Part 5: Field measurements
of airborne sound insulation of façade ele-ments and façades
• ISO 140-7:1998 Part 7: Field measurements
of impact sound insulation of floors
• ISO 140-14:2004 Part 14: Guidelines for spe-
cial situations in the field
• ISO 140-18:2006 Part 18: Laboratory mea-
surement of sound generated by rainfall on
building elements
• ISO 141:1976 Textile machinery and accessories --
Pirn winders and cross winders -- Definition of left
and right sides• ISO 142:1976 Textile machinery and accessories --
Weaving preparatory machines -- Definition of left
and right sides
• ISO 143:1977 Textile machinery and accessories --
Weft pirns for automatic looms [Withdrawn without
replacement]
• ISO 144:1973 Steel -- Reverse bend testing of wire
[Withdrawn: replaced with ISO 7801]
• ISO 146:1984 Metallic materials -- Hardness test -
- Verification of Vickers hardness testing machinesHV 0,2 to HV 100 [Withdrawn replaced with ISO
6507-2]
• ISO 146-2:1993 Metallic materials -- Verifi-
cation of Vickers hardness testing machines --
Part 2: Less than HV 0,2 [Withdrawn replaced
with ISO 6507-2]
• ISO 148 Metallic materials -- Charpy pendulum im-
pact test
• ISO 148-1:2009 Part 1: Test method
• ISO 148-2:2008 Part 2: Verification of testing
machines
• ISO 148-3:2008 Part 3: Preparation and char-
acterization of Charpy V-notch test pieces for
indirect verification of pendulum impact ma-
chines
• ISO 150:2006 Raw, refined andboiled linseed oilfor
paints and varnishes -- Specifications and methods
of test
• ISO 155:1998 Belt drives -- Pulleys -- Limiting val-
ues for adjustment of centres
• ISO 156:1982 Metallic materials -- Hardness test -- Verification of Brinell hardness testing machines
[Withdrawn replaced by ISO 6506-2]
• ISO 157:1996 Coal -- Determination of forms of
sulfur
• ISO 160:1980 Asbestos-cement pressure pipes and
joints [Withdrawn without replacement]
• ISO 161 Thermoplastics pipes for the conveyance
of fluids -- Nominal outside diameters and nominal
pressures
• ISO 161-1:1996 Part 1: Metric series
• ISO 161-2:1996 Part 2: Inch-based series
• ISO 162:1985 Cinematography -- Head gaps and
sound records for three-, four-, or six-track mag-
netic sound records on 35 mm and single-track on
17,5 mm motion-picture film containing no picture
-- Positions and width dimensions
• ISO 171:1980 Plastics -- Determination of bulk fac-
tor of moulding materials
• ISO 172:1978 Plastics -- Phenol-formaldehyde
mouldings -- Detection of free ammonia
• ISO 174:1974 Plastics -- Homopolymer and copoly-
mer resins of vinyl chloride -- Determination of
viscosity number in dilute solution [Withdrawn re-
placed by ISO 1628-2]
3 ISO 200 – ISO 999
• ISO 216:2007 Writing paper and certain classes of
printed matter – Trimmed sizes – A and B series,
and indication of machine direction
• ISO 226:2003 Acoustics – Normal equal-loudness-
level contours
• ISO 228 Pipe threads where pressure-tight joints are
not made on the threads
• ISO 228-1:2000 Dimensions, tolerances and
designation
• ISO 228-2:1987 Verification by means of limit
gauges
• ISO 233 Information and documentation – Translit-
eration of Arabic characters into Latin charac-
ters[Note 3]
• ISO 233-2:1993 Arabic language – Simplified
transliteration
• ISO 233-3:1999 Persian language – Simplified
transliteration
• ISO 259 Information and documentation – Translit-
eration of Hebrew characters into Latin charac-
ters[Note 3]
• ISO 259-2:1994 Simplified transliteration
Page 8
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 8/27
8 3 ISO 200 – ISO 999
• ISO 261 ISO general purpose metric screw threads
– General plan
• ISO 262 ISO general purpose metric screw threads
– Selected sizes for screws, bolts and nuts
•
ISO 286-1 Geometrical product specifications(GPS) – ISO code system for tolerances on linear
sizes – Part 1: Basis of tolerances, deviations and
fits
• ISO 286-2 Geometrical product specifications
(GPS) – ISO code system for tolerances on linear
sizes – Part 2: Tables of standard tolerance classes
and limit deviations for holes and shafts
• ISO 361 Basic ionizing radiation symbol
• ISO 500 Agricultural tractors – Rear-mounted
power take-off types 1, 2 and 3
• ISO 518:2006 Photography – Camera accessory
shoes, with and without electrical contacts, for
photoflash lamps and electronic photoflash units –
Specification
• ISO 519:1992 Photography – Hand-held cameras –
Flash-connector dimensions
• ISO 639 Codes for the representation of names of
languages
• ISO 639-1 Alpha-2 code
• ISO 639-2 Alpha-3 code
• ISO 639-3 Alpha-3 code for comprehensive
coverage of languages
• ISO 639-4 General principles of coding of the
representation of names of languages and re-
lated entities, and application guidelines
• ISO 639-5 Alpha-3 code for language families
and groups
• ISO 639-6 Alpha-4 code for comprehensive
coverage of language variants
• ISO/IEC 646 Information technology – ISO 7-bitcoded character set for information interchange
• ISO 657 Hot-rolled steel sections
• ISO 668 Series 1 freight containers – Classification,
dimensions and ratings
• ISO 690 Information and documentation – Guide-
lines for bibliographic references and citations to in-
formation resources
• ISO 704 Terminology work – Principles and meth-
ods
• ISO 732 Photography – 120-size and 220-size films
– Dimensions
• ISO 764 Horology – Magnetic resistant watches
• ISO 760:1978 Determination of water- Karl Fischer
method (General method)
• ISO 787 General methods of test for pigments and
extenders
• ISO 787-9:1981 Determination of pH value of
an aqueous suspension
• ISO 838 Paper – Holes for general filing purposes –
Specifications
• ISO 843:1997 Information and documentation –
Conversion of Greek characters into Latin charac-
ters
• ISO 860 Terminology work – Harmonization of
concepts and terms
• ISO 898 Mechanical properties of fasteners made of
carbon steel and alloy steel[Note 3]
• ISO 898-1 Bolts, screws and studs with speci-
fied property classes – Coarse thread and fine
pitch thread
• ISO 898-2 Nuts with specified proof load val-
ues – Coarse thread
• ISO 898-5 Set screws and similar threadedfas-
teners not under tensile stresses
•
ISO 898-6 Nuts with specified proof load val-ues – Fine pitch thread
• ISO 898-7 Torsional test and minimum
torques for bolts and screws with nominal di-
ameters 1 mm to 10 mm
• ISO 965 ISO general purpose metric screw threads
– Tolerances
• ISO 965-1 Principles and basic data
• ISO 965-2 Limits of sizes for general purpose
external and internal screw threads – Medium
quality
• ISO 965-3 Deviations for constructional screw
threads
• ISO 965-4 Limits of sizes for hot-dip galva-
nized external screw threads to mate with in-
ternal screw threads tapped with tolerance po-
sition H or G after galvanizing
• ISO 965-5 Limits of sizes for internal screw
threads to mate with hot-dip galvanized exter-
nal screw threads with maximum size of toler-
ance position h before galvanizing
• ISO 999 Information and documentation – Guide-lines for the content, organization, and presentation
of indexes
Page 9
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 9/27
9
4 ISO 1000 – ISO 4999
• ISO 1000 SI units and recommendations for the use
of their multiples and of certain other units [with-
drawn 2009-11-17]
• ISO 1004 Information processing – Magnetic inkcharacter recognition – Print specifications
• ISO 1007 Photography – 135-size film and maga-
zine – Specifications
• ISO 1101 Geometrical Product Specifications
(GPS) – Geometrical tolerancing – Tolerances of
form, orientation, location and run-out
• ISO 1222 Photography – Tripod connections
• ISO 1268 Fibre-reinforced plastics – Methods of
producing test plates
• ISO 1402 Rubber and plastics hoses and hose as-
semblies - Hydrostatic testing
• ISO/IEC 1539 Information technology – Program-
ming languages – Fortran
• ISO 1629 Rubber and latices – Nomenclature
• ISO 1663 Rigid cellular plastics – Determination of
water vapour transmission properties
• ISO 1745 Information processing – Basic mode con-
trol procedures for data communication systems
• ISO 1750 Pesticides and other agrochemicals –
Common names
• ISO 1928 Solid mineral fuels – Determination
of gross calorific value by the bomb calorimetric
method and calculation of net calorific value
• ISO/IEC 2022 Information technology – Character
code structure and extension techniques
• ISO 2108 Information and documentation –
International standard book number (ISBN)
• ISO 2145 Documentation – Numbering of divisionsand subdivisions in written documents
• ISO 2162 Technical product documentation –
Springs
• ISO 2162-1 Simplified representation
• ISO 2162-2 Presentation of data for cylindri-
cal helical compression springs
• ISO 2171 Cereals, pulses and by-products – Deter-
mination of ash yield by incineration
• ISO 2240:2003 Photography – Colour reversal cam-
era films – Determination of ISO speed
• ISO 2533 Standard Atmosphere
• ISO 2692 Geometrical product specifications (GPS)
– Geometrical tolerancing – Maximum material
requirement (MMR), least material requirement
(LMR) and reciprocity requirement (RPR)
• ISO 2709 Information and documentation – Format
for information exchange
• ISO 2768 General tolerances
• ISO 2768-1 Tolerances for linear and angular
dimensions without individual tolerance indi-
cations
• ISO 2768-2 Geometrical tolerances for fea-
tures without individual tolerance indications
• ISO 2852 Stainless steel clamp pipe couplings for
the food industry
• ISO 3002 Basic quantities in cutting and grinding
• ISO 3082 Iron ores – Sampling and sample prepa-
ration procedures
• ISO 3098 Technical product documentation – Let-
tering
• ISO 3103 Tea – Preparation of liquor for use in sen-
sory tests
• ISO 3166 Codes for the representation of names of
countries and their subdivisions
• ISO 3166-1 Country codes
• ISO 3166-2 Country subdivision code
• ISO 3166-3 Code for formerly used names of
countries
• ISO 3297 Information and documentation –
International standard serial number (ISSN)
• ISO 3394 Dimensions of rigid rectangular packages
– Transport packages
• ISO 3506 Mechanical properties of corrosion-
resistant stainless steel fasteners
• ISO 3534 Statistics – Vocabulary and symbols
• ISO 3534-1 General statistical terms and
terms used in probability
• ISO 3534-2 Applied statistics
• ISO 3534-3 Design of experiments
• ISO 3534-4 Survey sampling
• ISO 3536 Road vehicles – Safety glazing materials
– Vocabulary
• ISO 3537 Road vehicles – Safety glazing materials
– Mechanical tests
• ISO 3538 Road vehicles – Safety glazing materials
– Test methods for optical properties
Page 10
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 10/27
10 5 ISO 5000 – ISO 9999
• ISO 3601 Fluid power systems – O-rings
• ISO 3601-1 Inside diameters, cross-sections,
tolerances and designation codes
• ISO 3601-2 Housing dimensions for general
applications
• ISO 3601-3 Quality acceptance criteria
• ISO 3601-4 Anti-extrusion rings (back-up
rings)
• ISO 3601-5 Suitability of elastomeric materi-
als for industrial applications
• ISO 3602 Documentation – Romanization of
Japanese (kana script)
• ISO 3632 Spices – Saffron (Crocus sativus L.)[Note 3]
• ISO 3635:1981 Size designation of clothes – Defi-
nitions and body measurement procedure
• ISO 3676 Packaging – Unit load sizes – Dimensions
• ISO 3864 Graphical symbols – Safety colours and
safety signs
• ISO 3901 Information and documentation – Inter-
national Standard Recording Code (ISRC)
• ISO 3977 Gas turbines – Procurement
• ISO 4074 Natural latex rubber condoms – Require-
ments and test methods
• ISO 4157 Construction drawings – Designation sys-
tems
• ISO 4157-1 Buildings and part of buildings
• ISO 4157-2 Room names and numbers
• ISO 4157-3 Room identifiers
• ISO 4165 Road vehicles — Electrical connections
— Double-pole connection
• ISO 4179 Ductile iron pipes and fittings for pressure
and non-pressure pipelines – Cement mortar lining
• ISO 4217 Codes for the representation of currencies
and funds
• ISO 4314 Surface active agents — Determination of
free alkalinity or free acidity — Titrimetric method
• ISO 4578 Adhesives — Determination of peel resis-
tance of high-strength adhesive bonds — Floating-
roller method
• ISO 4582 Plastics — Determination of changes in
colour and variations in properties after exposure todaylight under glass, natural weathering or labora-
tory light sources
• ISO 4587 Adhesives — Determination of tensile
lap-shear strength of rigid-to-rigid bonded assem-
blies
• ISO 4628 Paints and varnishes – Evaluation of
degradation of coatings – Designation of quantity
and size of defects, and of intensity of uniformchanges in appearance
• ISO 4628-1 General introduction and designa-
tion system
• ISO 4628-2 Assessment of degree of blister-
ing
• ISO 4628-3 Assessment of degree of rusting
• ISO 4628-4 Assessment of degree of cracking
• ISO 4628-5 Assessment of degree of flaking
• ISO 4628-6 Assessment of degree of chalking
by tape method
• ISO 4628-7 Assessment of degree of chalking
by velvet method
• ISO 4628-8 Assessment of degree of delami-
nation and corrosion around a scribe
• ISO 4628-10 Assessment of degree of filiform
corrosion
• ISO/IEC 4873:1991 Information technology – ISO
8-bit code for information interchange – Structure
and rules for implementation
• ISO 4892 Plastics – Methods of exposure to labora-
tory light sources
5 ISO 5000 – ISO 9999
• ISO 5127 Information and documentation – Vocab-
ulary
• ISO 5167 Measurement of fluid flow by means
of pressure differential devices inserted in circular
cross-section conduits running full
• ISO 5167-1 General principles and require-
ments
• ISO 5167-2 Orifice plates
• ISO 5167-3 Nozzles and Venturi nozzles
• ISO 5167-4 Venturi tubes
• ISO/IEC 5218 Information technology – Codes for
the representation of human sexes
• ISO 5455 Technical drawings – Scales
• ISO 5457 Technical product documentation – Sizes
and layout of drawing sheets
• ISO 5458 Geometrical Product Specifications(GPS) – Geometrical tolerancing – Positional tol-
erancing
Page 11
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 11/27
11
• ISO 5459 Geometrical product specifications (GPS)
– Geometrical tolerancing – Datums and datum sys-
tems
• ISO 5660 Reaction-to-fire tests – Heat release,
smoke production and mass loss rate
• ISO 5660-1 Heat release rate (cone calorime-
ter method)
• ISO 5660-2 Smoke production rate (dynamic
measurement)
• ISO/TS 5660-3 Guidance on measurement
• ISO 5725 Accuracy (trueness and precision) of mea-
surement methods and results
• ISO 5775 Bicycle tires and rims
• ISO 5776 Graphic technology - Symbols for text
correction
• ISO 5800:2001 Photography – Colour negative
films for still photography – Determination of ISO
speed
• ISO 5893 Rubber and plastics test equipment – Ten-
sile, flexural and compression types (constant rate of
traverse) – Specification
• ISO 5964 Documentation – Guidelines for the es-
tablishment and development of multilingual the-
sauri
• ISO 5971:1981 Size designation of clothes – Panty-
hose
• ISO 5993 Sodium hydroxide for industrial use -
- Determination of mercury content -- Flameless
atomic absorption spectrometric method
• ISO 6107-4:1993 Water quality -- Vocabulary
• ISO 6166 Securities and related financial instru-
ments – International securities identification num-
bering system (ISIN)
• ISO 6194 Rotary-shaft lip-type seals incorporatingelastomeric sealing elements
• ISO 6194-5 Identification of visual imperfec-
tions
• ISO 6336 Calculation of load capacity of spur and
helical gears
• ISO 6344 Coated abrasives – Grain size analysis
• ISO 6344-1 Grain size distribution test
• ISO 6344-2 Determination of grain size dis-
tribution of macrogrits P12 to P220• ISO 6344-3 Determination of grain size dis-
tribution of microgrits P240 to P2500
• ISO 6357 Documentation – Spine titles on books
and other publications
• ISO/IEC 6429 Information technology – Control
functions for coded character sets
• ISO 6438 Documentation – African coded character
set for bibliographic information interchange
• ISO/IEC 6523 Information technology – Structure
for the identification of organizations and organiza-
tion parts
• ISO 6579 Microbiology of food and animal feed-
ing stuffs – Horizontal method for the detection of
Salmonella spp.
• ISO 6594 Cast iron drainage pipes and fittings –
Spigot series
•
ISO 6709 Standard representation of geographicpoint location by coordinates
• ISO 6946 Building components and building ele-
ments – Thermal resistance and thermal transmit-
tance – Calculation method
• ISO 7001 Graphical symbols – Public information
symbols
• ISO 7002 Agricultural food products – Layout for a
standard method of sampling from a lot
• ISO 7098 Information and documentation – Ro-
manization of Chinese
• ISO 7200 Technical product documentation – Data
fields in title blocks and document headers
• ISO 7240 Fire detection and alarm systems
• ISO 7372 Trade data interchange
• ISO/IEC 7498 Information technology -- Open
Systems Interconnection -- Basic Reference
Model[Note 3]
• ISO/IEC 7498-1 The Basic Model
• ISO 7498-2 Security Architecture
• ISO/IEC 7498-3 Naming and addressing
• ISO/IEC 7498-4 Management framework
• ISO/IEC 7501 Identification cards – Machine read-
able travel documents
• ISO/IEC 7501-1:2008 Machine readable
passport
• ISO/IEC 7501-2:1997 Machine readable visa
• ISO/IEC 7501-3:2005 Machine readable offi-
cial travel documents
• ISO 7736 Road vehicles – Car radio for front instal-
lation – Installation space including connections
Page 12
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 12/27
12 5 ISO 5000 – ISO 9999
• ISO/IEC 7810 Identification cards – Physical char-
acteristics
• ISO/IEC 7811 Identification cards – Recording
technique
• ISO/IEC 7812 Identification cards – Identification
of issuers
• ISO/IEC 7813 Information technology – Identifica-
tion cards – Financial transaction cards
• ISO/IEC 7816 Identification cards – Integrated cir-
cuit cards[Note 3]
• ISO/IEC 7816-1 Cards with contacts — Phys-
ical characteristics
• ISO/IEC 7816-2 Cards with contacts — Di-
mensions and location of the contacts
•
ISO/IEC 7816-3 Cards with contacts — Elec-trical interface and transmission protocols
• ISO/IEC 7816-4 Organization, security and
commands for interchange
• ISO/IEC 7816-5 Registration of application
providers
• ISO/IEC 7816-6 Interindustry data elements
for interchange
• ISO/IEC 7816-7 Interindustry commands for
Structured Card Query Language (SCQL)
• ISO/IEC 7816-8 Commands for security op-
erations• ISO/IEC 7816-9 Commands for card manage-
ment
• ISO/IEC 7816-10 Electronic signals and an-
swer to reset for synchronous cards
• ISO/IEC 7816-11 Personal verification
through biometric methods
• ISO/IEC 7816-12 Cards with contacts — USB
electrical interface and operating procedures
• ISO/IEC 7816-13 Commands for application
management in multi-application environment
• ISO/IEC 7816-15 Cryptographic informationapplication
• ISO/IEC 7942 Information technology – Computer
graphics and image processing – Graphical Kernel
System (GKS)
• ISO 8000 Data quality
• ISO 8015:2011 Geometrical product specifications
(GPS) – Fundamentals – Concepts, principles and
rules
• ISO 8090 Cycles – Terminology
• ISO 8180 Ductile iron pipelines – Polyethylene
sleeving for site application
• ISO 8373 Manipulating industrial robots – Vocabu-
lary
• ISO 8501 Preparation of steel substrates before ap-
plication of paints and related products – Visual as-
sessment of surface cleanliness
• ISO 8559:1989 Garment construction and anthro-
pometric surveys – Body dimensions
• ISO 8573 Compressed air
• ISO 8573-1 Contaminants and purity classes
• ISO 8573-2 Test methods for oil aerosol con-
tent
• ISO 8573-3 Test methods for measurement of
humidity
• ISO 8573-4 Test methods for solid particle
content• ISO 8573-5 Test methods for oil vapour and
organic solvent content
• ISO 8573-6 Test methods for gaseous contam-
inant content
• ISO 8573-7 Test method for viable microbio-
logical contaminant content
• ISO 8573-8 Test methods for solid particle
content by mass concentration
• ISO 8573-9 Test methods for liquid water con-
tent
• ISO 8583 Financial transaction card originated mes-
sages – Interchange message specifications
• ISO 8583-1 Messages, data elements and code
values
• ISO 8583-2 Application and registration pro-
cedures for Institution Identification Codes
(IIC)
• ISO 8583-3 Maintenance procedures for mes-
sages, data elements and code values
• ISO 8601 Data elements and interchange formats –
Information interchange – Representation of datesand times
• ISO/IEC 8613 Information technology – Open Doc-
ument Architecture (ODA) and interchange format
• ISO/IEC 8632 Information technology – Computer
graphics – Metafile for the storage and transfer of
picture description information
• ISO/IEC 8632-1 Functional specification
• ISO/IEC 8632-2 Character encoding
•
ISO/IEC 8632-3 Binary encoding [withdrawn2001-06-21]
• ISO/IEC 8632-4 Clear text encoding
Page 13
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 13/27
13
• ISO 8651 Information technology – Computer
graphics – Graphical Kernel System (GKS) lan-
guage bindings[Note 3]
• ISO/IEC 8652 Information technology – Program-
ming languages – Ada
• ISO 8653:1986 Jewellery – Ring-sizes – Definition,
measurement and designation
• ISO 8691 Petroleum products – Low levels of vana-
dium in liquid fuels – Determination by flameless
atomic absorption spectrometry after ashing
• ISO 8805 Information processing systems – Com-
puter graphics – Graphical Kernel System for Three
Dimensions (GKS-3D) functional description
• ISO/IEEC 8806 Information technology – Com-
puter graphics – Graphical Kernel System for Three
Dimensions (GKS-3D) language bindings
• ISO/IEEC 8806-4 C
• ISO 8807 Information processing systems – Open
Systems Interconnection – LOTOS – A formal de-
scription technique based on the temporal ordering
of observational behaviour
• ISO/IEC 8824 Information technology – Abstract
Syntax Notation One (ASN.1)
• ISO/IEC 8825 Information technology – ASN.1 en-
coding rules
• ISO/IEC 8859 Information technology – 8-bit
single-byte coded graphic character sets
• ISO/IEC 8859-1 Latin alphabet No. 1
• ISO/IEC 8859-2 Latin alphabet No. 2
• ISO/IEC 8859-3 Latin alphabet No. 3
• ISO/IEC 8859-4 Latin alphabet No. 4
• ISO/IEC 8859-5 Latin/Cyrillic alphabet
• ISO/IEC 8859-6 Latin/Arabic alphabet
• ISO/IEC 8859-7 Latin/Greek alphabet
• ISO/IEC 8859-8 Latin/Hebrew alphabet
• ISO/IEC 8859-9 Latin alphabet No. 5
• ISO/IEC 8859-10 Latin alphabet No. 6
• ISO/IEC 8859-11 Latin/Thai alphabet
• ISO/IEC 8859-13 Latin alphabet No. 7
• ISO/IEC 8859-14 Latin alphabet No. 8
(Celtic)
• ISO/IEC 8859-15 Latin alphabet No. 9
• ISO/IEC 8859-16 Latin alphabet No. 10
• ISO 8879 Information processing – Text and officesystems – Standard Generalized Markup Language
(SGML)
• ISO 9000 Quality management systems – Funda-
mentals and vocabulary
• ISO 9001 Quality management systems – Require-
ments
•
ISO 9004 Managing for the sustained success of anorganization – A quality management approach
• ISO 9050 Glass in building – Determination of light
transmittance, solar direct transmittance, total solar
energy transmittance, ultraviolet transmittance and
related glazing factors
• ISO 9069 Information processing – SGML support
facilities – SGML Document Interchange Format
(SDIF)
• ISO/IEC 9075 Information technology – Database
languages – SQL
• ISO/IEC 9126 Software engineering – Product
quality
• ISO 9141 Road vehicles – Diagnostic systems[Note 3]
• ISO 9141-2 CARB requirements for inter-
change of digital information
• ISO 9141-3 Verification of the communica-
tion between vehicle and OBD II scan tool
• ISO 9241 Ergonomics of human-system interaction
•
ISO/IEC 9293 Information technology – Volumeand file structure of disk cartridges for information
interchange
• ISO 9362 Banking – Banking telecommunication
messages – Business identifier code (BIC)
• ISO 9407 Shoe sizes – Mondopoint system of sizing
and marking
• ISO/IEC 9541 Information technology – Font infor-
mation interchange
• ISO/IEC 9541-1:1991 Architecture
• ISO/IEC 9541-2:1991 Interchange Format
• ISO/IEC 9541-3:1994 Glyph shape represen-
tation
• ISO/IEC 9541-4:2009 Harmonization to
Open Font Format
• ISO 9564 Financial services – Personal Identifica-
tion Number (PIN) management and security[Note 3]
• ISO/IEC 9579 Information technology – Remote
database access for SQL with security enhancement
• ISO/IEC 9592 Information technology – Computergraphics and image processing – Programmer’s Hi-
erarchical Interactive Graphics System (PHIGS)
Page 14
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 14/27
14 6 ISO 10000 – ISO 14999
• ISO/IEC 9593 Information technology – Computer
graphics – Programmer’s Hierarchical Interactive
Graphics System (PHIGS) language bindings[Note 3]
• ISO/IEC 9594 Information technology – Open Sys-
tems Interconnection – The Directory
• ISO/IEC 9636 Information technology - Computer
graphics - Interfacing techniques for dialogues with
graphical devices (CGI) - Functional specification
• ISO/IEC 9636-1 Overview, profiles, and con-
formance
• ISO/IEC 9636-2 Control
• ISO/IEC 9636-3 Output
• ISO/IEC 9636-4 Segments
• ISO/IEC 9636-5 Input and echoing
• ISO/IEC 9636-6 Raster
• ISO 9660 Information processing – Volume and file
structure of CD-ROM for information interchange
• ISO 9712 Non-destructive testing - Qualification
and certification of NDT personnel
• ISO/IEC 9796 Information technology – Security
techniques – Digital signature schemes giving mes-
sage recovery
• ISO/IEC 9797 Information technology – Secu-
rity techniques – Message Authentication Codes
(MACs)
• ISO/IEC 9797-1 Mechanisms using a block
cipher
• ISO/IEC 9797-2 Mechanisms using a dedi-
cated hash-function
• ISO/IEC 9798 Information technology – Security
techniques – Entity authentication
• ISO/IEC 9834 Information technology – Open Sys-
tems Interconnection – Procedures for the operation
of OSI Registration Authorities
• ISO 9869 Thermal insulation – Building elements– In-situ measurements of thermal resistance and
thermal transmittance
• ISO/IEC 9899 Programming languages – C
• ISO/IEC/IEEE 9945 Information technology –
Portable Operating System Interface (POSIX®)
Base Specifications, Issue 7
• ISO 9984 Information and documentation –
Transliteration of Georgian characters into Latin
characters
• ISO 9985 Information and documentation –Transliteration of Armenian characters into Latin
characters
• ISO 9992 Financial transaction cards – Messages
between the integrated circuit card and the card ac-
cepting device
• ISO/IEC 9995 Information technology – Keyboard
layouts for text and office systems
• ISO 9999 Assistive products for persons with dis-
ability – Classification and terminology
6 ISO 10000 – ISO 14999
• ISO 10001:2007 Quality management – Customer
satisfaction – Guidelines for codes of conduct for
organizations
• ISO 10002:2014 Quality management – Customer
satisfaction – Guidelines for complaints handling in
organizations
• ISO 10003:2007 Quality management – Customer
satisfaction – Guidelines for dispute resolution ex-
ternal to organizations
• ISO 10004:2008 Quality management – Customer
satisfaction – Guidelines for monitoring and mea-
suring
• ISO 10005:2005 Quality management systems –
Guidelines for quality plans
•
ISO 10006:2003 Quality management systems –Guidelines for quality management in projects
• ISO 10007:2003 Quality management systems –
Guidelines for configuration management
• ISO 10012:2003 Measurement management sys-
tems – Requirements for measurement processes
and measuring equipment
• ISO/TR 10013:2001 Guidelines for quality manage-
ment system documentation
• ISO 10014:2006 Quality management – Guidelines
for realizing financial and economic benefits
• ISO 10015:1999 Quality management – Guidelines
for training
• ISO/TR 10017:2003 Guidance on statistical tech-
niques for ISO 9001:2000
• ISO 10018:2012 Quality management – Guidelines
on people involvement and competence
• ISO 10019:2005 Guidelines for the selection of
quality management system consultants and use of
their services
• ISO/IEC 10021 Information technology – Message
Handling Systems (MHS)
Page 15
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 15/27
15
• ISO/IEC 10026 Information technology – Open
Systems Interconnection
• ISO 10077 Thermal performance of windows, doors
and shutters – Calculation of thermal transmittance
• ISO/IEC 10089 Information technology – 130 mm
rewritable optical disk cartridge for information in-
terchange
• ISO/IEC 10116 Information technology – Security
techniques – Modes of operation for an n-bit block
cipher
• ISO/IEC 10118 Information technology – Security
techniques – Hash-functions
• ISO 10160 Information and documentation – Open
Systems Interconnection – Interlibrary Loan Appli-
cation Service Definition
• ISO 10161 Information and documentation – Open
Systems Interconnection – Interlibrary Loan Appli-
cation Protocol Specification
• ISO/IEC 10164 Information technology – Open
Systems Interconnection – Systems Management
• ISO/IEC 10179:1996 Information technology –
Processing languages – Document Style Semantics
and Specification Language (DSSSL)
• ISO/IEC 10206 Information technology – Program-
ming languages – Extended Pascal• ISO 10211 Thermal bridges in building construction
– Heat flows and surface temperatures – Detailed
calculations
• ISO 10218 Robots and robotic devices – Safety re-
quirements for industrial robots
• ISO/IEC 10279 Information technology – Program-
ming languages – Full BASIC
• ISO 10303 Industrial automation systems and inte-
gration – Product data representation and exchange
• ISO 10380 Pipework — Corrugated metal hoses
and hose assemblies
• ISO 10383 Securities and related financial instru-
ments – Codes for exchanges and market identifica-
tion (MIC)
• ISO 10456 Building materials and products – Hy-
grothermal properties – Tabulated design values
and procedures for determining declared and design
thermal values
• ISO 10487 Passenger cars – Connections for car
radios[Note 3]
• ISO 10555 Sterile, single-use intravascular catheters
• ISO 10579 Geometrical product specifications
(GPS) – Dimensioning and tolerancing – Non-rigid
parts
• ISO 10628 Flow diagrams for process plants
• ISO/IEC 10646 Information technology – Universal
Coded Character Set (UCS)
• ISO 10664 Hexalobular internal driving feature for
bolts and screws – Torx screw head
• ISO/IEC 10746 Information technology - Open dis-
tributed processing
• ISO/IEC 10746-1 Information technology -
Open Distributed Processing - Reference
model: Overview
• ISO/IEC 10746-2 Information technology
- Open distributed processing - Reference
model: Foundations
• ISO/IEC 10746-3 Information technology
- Open distributed processing - Reference
model: Architecture
• ISO/IEC 10746-4 Information technology -
Open Distributed Processing - Reference
Model: Architectural semantics
• ISO 10957 Information and documentation –
International standard music number (ISMN)
• ISO 10962 Securities and related financial instru-
ments – Classification of Financial Instruments (CFIcode)
• ISO 10993 Biological evaluation of medical devices
• ISO 10993-1 Evaluation and testing within a
risk management process
• ISO 10993-2 Animal welfare requirements
• ISO 10993-3 Tests for genotoxicity, carcino-
genicity and reproductive toxicity
• ISO 10993-4 Selection of tests for interactions
with blood
• ISO 10993-5 Tests for in vitro cytotoxicity
• ISO 10993-6 Tests for local effects after im-
plantation
• ISO 10993-7 Ethylene oxide sterilization
residuals
• ISO 10993-9 Framework for identification
and quantification of potential degradation
products
• ISO 10993-10 Tests for irritation and skin sen-
sitization
•
ISO 10993-11 Tests for systemic toxicity• ISO 10993-12 Sample preparation and refer-
ence materials
Page 16
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 16/27
16 6 ISO 10000 – ISO 14999
• ISO 10993-13 Identification and quantifica-
tion of degradation products from polymeric
medical devices
• ISO 10993-14 Identification and quantifica-
tion of degradation products from ceramics
• ISO 10993-15 Identification and quantifica-tion of degradation products from metals and
alloys
• ISO 10993-16 Toxicokinetic study design for
degradation products and leachables
• ISO 10993-17 Establishment of allowable
limits for leachable substances
• ISO 10993-18 Chemical characterization of
materials
• ISO 10993-19 Physico-chemical, morpholog-
ical and topographical characterization of ma-
terials
• ISO 10993-20 Principles and methods for im-
munotoxicology testing of medical devices
• ISO 11064 Ergonomic design of control centres
• ISO 11064-1:2000 Principles for the design of
control centres
• ISO 11064-2:2000 Principles for the arrange-
ment of control suites
• ISO 11064-3:1999 Control room layout ISO
11064-3:1999/Cor 1:2002
• ISO 11064-4:2004 Layout and dimensions of
workstations
• ISO 11064-5:2008 Displays and controls
• ISO 11064-6:2005 Environmental require-
ments for control centres
• ISO 11064-7:2006 Principles for the evalua-
tion of control centres
• ISO 11120 Gas cylinders -- Refillable seamless steel
tubes for compressed gas transport, of water capac-
ity between 150 l and 3000 l -- Design construction
and testing
• ISO 11135:2014 Sterilization of health-care prod-
ucts -- Ethylene oxide -- Requirements for the de-
velopment, validation and routine control of a ster-
ilization process for medical devices
• ISO 11137 Sterilization of health care products –
Radiation
• ISO 11170:2003 Hydraulic fluid power – Filter ele-
ments – Sequence of tests for verifying performance
characteristics
• ISO 11171:2010 Hydraulic fluid power – Calibra-
tion of automatic particle counters for liquids
• ISO/IEC 11172 Information technology – Coding
of moving pictures and associated audio for digital
storage media at up to about 1,5 Mbit/s
• ISO/IEC 11179 Information technology – Metadata
registries (MDR)
• ISO/IEC 11179-1:2004 Framework
• ISO/IEC 11179-2:2005 Classification
• ISO/IEC 11179-3:2003 Registry metamodel
and basic attributes
• ISO/IEC 11179-4:2004 Formulation of data
definitions
• ISO/IEC 11179-5:2005 Naming and identifi-
cation principles
• ISO/IEC 11179-6:2005 Registration
• ISO 11357 Plastics – Differential scanning
calorimetry (DSC)
• ISO 11357-1:2009 General principles
• ISO 11357-2:2013 Determination of glass
transition temperature and glass transition step
height
• ISO 11357-3:2011 Determination of temper-
ature and enthalpy of melting and crystalliza-
tion
• ISO 11357-4:2005 Determination of specific
heat capacity
• ISO 11357-5:2013 Determination of charac-
teristic reaction-curve temperatures and times,
enthalpy of reaction and degree of conversion
• ISO 11357-6:2008 Determination of oxida-
tion induction time (isothermal OIT) and oxi-
dation induction temperature (dynamic OIT)
• ISO 11357-7:2002 Determination of crystal-
lization kinetics
• ISO/IEC 11404 Information technology – General-
Purpose Datatypes (GPD)
• ISO 11446:2004 Road vehicles – Connectors for the
electrical connection of towing and towed vehicles –13-pole connectors for vehicles with 12 V nominal
supply voltage
• ISO 11469:2000 Plastics – Generic identification
and marking of plastics products
• ISO/IEC 11578:1996 Information technology –
Open Systems Interconnection – Remote procedure
call (RPC)
• ISO 11783 Tractors and machinery for agriculture
and forestry – Serial control and communications
data network
• ISO/IEC 11801 Information technology – Generic
cabling for customer premises
Page 17
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 17/27
17
• ISO 11898 Road vehicles – Controller area network
(CAN)
• ISO 12006 Building construction – Organization of
information about construction works
• ISO/IEC 12207 Systems and software engineering
– Software life cycle processes
• ISO 12100 Safety of machinery – General principles
for design – Risk assessment and risk reduction
• ISO 12639 Graphic technology – Prepress digital
data exchange – Tag image file format for image
technology (TIFF/IT)
• ISO 12641 Graphic technology – Prepress digital
data exchange – Colour targets for input scanner cal-
ibration
• ISO/TS 12805:2011 Nanotechnologies – Materi-als specifications – Guidance on specifying nano-
objects
• ISO 12859/TR Intelligent transport systems – Sys-
tem architecture – Privacy aspects in ITS standards
and systems
• ISO 12944 Paints and varnishes – Corrosion protec-
tion of steel structures by protective paint systems
• ISO 13007 Ceramic tiles – Grouts and adhesives
• ISO 13007-1:2014 Terms, definitions and
specifications for adhesives
• ISO 13007-2:2010 Test methods for adhesives
• ISO 13007-3:2010 Terms, definitions and
specifications for grouts
• ISO 13007-4:2013 Test methods for grouts
• ISO/TR 13121:2011 Nanotechnologies – Nanoma-
terial risk evaluation
• ISO 13239 Information technology – Telecommuni-
cations and information exchange between systems
– High-level data link control (HDLC) procedures
• ISO/IEC 13249 Information technology – Database
languages – SQL multimedia and application
• ISO/IEC 13250 Information technology – Topic
Maps[Note 3]
• ISO 13320:2009 Particle size analysis - Laser
diffraction methods
• ISO/IEC 13346 Information technology – Volume
and file structure of write-once and rewritable me-
dia using non-sequential recording for information
interchange
• ISO 13370 Thermal performance of buildings –
Heat transfer via the ground – Calculation methods
• ISO 13406-2:2001 Ergonomic requirements for
work with visual displays based on flat panels – Part
2: Ergonomic requirements for flat panel displays
[withdrawn 2008-11-14]
• ISO 13450 Photography – 110-size cartridge, film
and backing paper – Dimensions
• ISO 13485:2003 Medical devices – Quality man-
agement systems – Requirements for regulatory pur-
poses
• ISO/IEC 13490 Information technology – Volume
and file structure of read-only and write-once com-
pact disk media for information interchange
• ISO 13567 Technical product documentation – Or-
ganization and naming of layers for CAD
• ISO/IEC 13568:2002 Information Technology – Z
formal specification notation – Syntax, type system
and semantics
• ISO 13577 Industrial furnaces and associated pro-
cessing equipment - Safety
• ISO 13577-1 General requirements
• ISO 13579 Industrial furnaces and associated pro-
cessing equipment - Method of measuring energy
balance and calculating efficiency
• ISO 13579-1 General methodology
• ISO 13579-2 Reheating furnaces for steel
• ISO 13579-3 Batch-type aluminium melting
furnaces
• ISO 13579-4 Furnaces with protective or re-
active atmosphere
• ISO 13586:2000 Plastics - Determination of frac-
ture toughness (GIC and KIC) -- Linear elastic frac-
ture mechanics (LEFM) approach
• ISO 13616 Financial services – International bank
account number (IBAN)
• ISO 13628 Petroleum and natural gas industries –
Design and operation of subsea production systems
• ISO 13628-1 General requirements and rec-
ommendations
• ISO 13628-2 Unbonded flexible pipe systems
for subsea and marine applications
• ISO 13628-3 Through flowline (TFL) systems
• ISO 13628-4 Subsea wellhead and tree equip-
ment
•
ISO 13628-5 Subsea umbilicals• ISO 13628-6 Subsea production control sys-
tems
Page 18
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 18/27
18 6 ISO 10000 – ISO 14999
• ISO 13628-7 Completion/workover riser sys-
tems
• ISO 13628-8 Remotely Operated Vehicle
(ROV) interfaces on subsea production sys-
tems
• ISO 13628-9 Remotely Operated Tool (ROT)intervention systems
• ISO 13628-10 Specification for bonded flexi-
ble pipe
• ISO 13628-11 Flexible pipe systems for sub-
sea and marine applications
• ISO 13715 Technical drawings—Edges of unde-
fined shape—Vocabulary and indications
• ISO 13849 Safety of machinery – Safety related
parts of control systems
• ISO/IEC 13818 Information technology – Genericcoding of moving pictures and associated audio in-
formation
• ISO 13837 Road vehicles – Safety glazing materials
– Method for the determination of solar transmit-
tance
• ISO 14000 Environmental management systems
[This is a set of standards, rather than a single stan-
dard.]
• ISO 14001:2004 Environmental management sys-
tems – Requirements with guidance for use
• ISO 14004:2004 Environmental management sys-
tems – General guidelines on principles, systems and
support techniques
• ISO 14031 Environmental management - Environ-
mental performance evaluation – Guidelines
• ISO 14050 Environmental management – Vocabu-
lary
• ISO 14051 Environmental management – Material
flow cost accounting - General framework
• ISO 14064 Greenhouse gases
• ISO 14155:2011 Clinical investigation of medical
devices for human subjects – Good clinical practice
• ISO 14223 Radiofrequency [sic ] identification of
animals – Advanced transponders
• ISO 14224 Petroleum, petrochemical and natural
gas industries - Collection and exchange of reliabil-
ity and maintenance data for equipment
• ISO 14230 Road vehicles – Diagnostic systems –
Keyword Protocol 2000
• ISO 14230-1 Physical layer
• ISO 14230-2 Data link layer
• ISO 14230-3 Application layer
• ISO 14230-4 Requirements for emission-
related systems
•
ISO 14405-1 Geometrical product specifications(GPS) – Dimensional tolerancing – Part 1: Linear
sizes
• ISO/IEC 14443 Identification cards – Contactless
integrated circuit cards – Proximity cards
• ISO/IEC 14462 - Open-EDI Reference Model
• ISO/IEC 14496 Information technology – Coding
of audio-visual objects
• ISO 14641 Electronic archiving
• ISO 14641-1:2012 Specifications concerningthe design and the operation of an information
system for electronic information preservation
• ISO 14644 Cleanrooms and associated controlled
environments
• ISO 14644-1:1999 Classification of air clean-
liness
• ISO 14644-2:2000 Specifications for testing
and monitoring to prove continued compliance
with ISO 14644-1
• ISO 14644-3:2005 Test methods
• ISO 14644-4:2001 Design, construction and
start-up
• ISO 14644-5:2004 Operations
• ISO 14644-6:2007 Vocabulary
• ISO 14644-7:2004 Separative devices (clean
air hoods, gloveboxes, isolators and mini-
environments)
• ISO 14644-8:2006 Classification of airborne
molecular contamination
• ISO/IEC 14651 Information technology – Interna-
tional string ordering and comparison – Method for
comparing character strings and description of the
common template tailorable ordering
• ISO 14698 Cleanrooms and associated controlled
environments – Biocontamination control
• ISO 14698-1 General principles and methods
• ISO 14698-2 Evaluation and interpretation of
biocontamination data
• ISO/IEC 14750 Information technology – OpenDistributed Processing – Interface Definition Lan-
guage
Page 19
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 19/27
19
• ISO/IEC 14755 Information technology – Input
methods to enter characters from the repertoire of
ISO/IEC 10646 with a keyboard or other input de-
vice
• ISO 14801 Dentistry – Implants – Dynamic fatigue
test for endosseous dental implants
• ISO 14855-1 Determination of the ultimate aero-
bic biodegradability of plastic materials under con-
trolled composting conditions – Method by analysis
of evolved carbon dioxide
• ISO 14855-1:2005 General method
• ISO 14855-2:2007 Gravimetric measurement of
carbon dioxide evolved in a laboratory-scale test
• ISO/IEC 14882 Programming Languages – C++
• ISO 14915 Software ergonomics for multimediauser interfaces
• ISO 14915-1:2002 Design principles and
framework
• ISO 14915-2:2003 Multimedia navigation and
control
• ISO 14915-3:2002 Media selection and com-
bination
• ISO 14971:2007 Medical devices – Application of
risk management to medical devices
• ISO/IEC 14977 Information technology – Syntactic
metalanguage – Extended BNF
7 ISO 15000 – ISO 19999
• ISO/TS 15000 Electronic business eXtensible
Markup Language ebXML
• ISO/TS 15000-1:2004 Collaboration-protocol
profile and agreement specification (ebCPP)
• ISO/TS 15000-2:2004 Message service spec-ification (ebMS)
• ISO/TS 15000-3:2004 Registry information
model specification (ebRIM)
• ISO/TS 15000-4:2004 Registry services spec-
ification (ebRS)
• ISO/TS 15000-5:2005 ebXML. Core Com-
ponents Technical Specification, Version
2.01(ebCCTS)
• ISO 15022 Securities – Scheme for messages (Data
Field Dictionary)
• ISO 15082 Road vehicles – Tests for rigid plastic
safety glazing materials
• ISO 15099 Thermal performance of windows, doors
and shading devices – Detailed calculations
• ISO 15112 Natural gas – Energy determination
• ISO 15189 Medical laboratories – Particular re-
quirements for quality and competence
• ISO 15223 Medical devices – Symbols to be used
with medical device labels, labelling, and informa-
tion to be supplied
• ISO/IEC 15288 Systems and software engineering
– System life cycle processes
• ISO/IEC 15289 Systems and software engineering
– Content of systems and software life cycle process
information products (Documentation)
• ISO/IEC 15291 Information technology – Program-
ming languages – Ada Semantic Interface Specifica-
tion (ASIS)
• ISO 15403 Natural gas – Natural gas for use as a
compressed fuel for vehicles
• ISO 15403-1 Designation of the quality
• ISO/IEC 15408 Information technology – Security
techniques – Evaluation criteria for IT security
• ISO/IEC 15414 - Open data processing - Reference
Model - Enterprise Language
• ISO/IEC 15434 Information technology – Auto-
matic identification and data capture techniques –Syntax for high-capacity ADC media
• ISO/IEC 15444 Information technology – JPEG
2000 image coding system
• ISO/IEC 15445:2000 Information technology –
Document description and processing languages –
HyperText Markup Language (HTML)
• ISO 15489-1:2001 Information and documentation
– Records management – Part 1: General
• ISO/TR 15489-2:2001 Information and documen-
tation – Records management – Part 2: Guidelines
• ISO/IEC 15504 Information technology – Process
assessment
• ISO 15614 Specification and qualification of weld-
ing procedures for metallic materials – Welding pro-
cedure test
• ISO 15686 Buildings and constructed assets – Ser-
vice life planning
• ISO/IEC 15693 Identification cards – Contactless
integrated circuit cards – Vicinity cards
• ISO 15706 Information and documentation – Inter-
national Standard Audiovisual Number (ISAN)
Page 20
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 20/27
20 7 ISO 15000 – ISO 19999
• ISO 15707 Information and documentation – Inter-
national Standard Musical Work Code (ISWC)
• ISO 15783:2002 Seal-less rotodynamic pumps –
Class II – Specification
• ISO 15836 Information and documentation – The
Dublin Core metadata element set
• ISO/IEC 15897 Information technology – Proce-
dures for registration of cultural elements
• ISO 15924 Information and documentation – Codes
for the representation of names of scripts
• ISO 15926 - Integration of Life-cycle Data for Pro-
cess Plants including Oil and Gas Production Facil-
ities
• ISO 15930 Graphic technology – Prepress digital
data exchange using PDF[Note 3]
• ISO/IEC 15944 - Business Agreement Semantic
Descriptive Techniques
• ISO/IEC 15948 Information technology – Com-
puter graphics and image processing – Portable Net-
work Graphics (PNG): Functional specification
• ISO 15970 Natural gas – Measurement of properties
– Volumetric properties: density, pressure, temper-
ature and compression factor
• ISO 15971:2008 Natural gas – Measurement of
properties – Calorific value and Wobbe index
• ISO 15985:2004 Plastics – Determination of the ul-
timate anaerobic biodegradation and disintegration
under high-solids anaerobic-digestion conditions –
Method by analysis of released biogas
• ISO 16134 Earthquake- and subsidence-resistant
design of ductile iron pipelines
• ISO 16232 Road vehicles – Cleanliness of compo-
nents of fluid circuits
•
ISO 16232-8 Particle nature determination bymicroscopic analysis
• ISO 16232-9 Particle sizing and counting by
automatic light extinction particle counter
• ISO 16232-10 Expression of results
• ISO/IEC 16262 Information technology – Program-
ming languages, their environments and system soft-
ware interfaces – ECMAScript language specifica-
tion
• ISO/IEC 16500 Information technology – Generic
digital audio-visual systems
• ISO 16549 Textiles – Unevenness of textile strands
– Capacitance method
• ISO 16750 Road vehicles – Environmental condi-
tions and testing for electrical and electronic equip-
ment
• ISO 16792 Technical product documentation - Dig-
ital product definition data practices
• ISO/TS 16949 Quality management systems – Par-
ticular requirements for the application of ISO
9001:2008 for automotive production and relevant
service part organizations
• ISO/TR 16982:2002 Ergonomics of human-system
interaction – Usability methods supporting human-
centred design
• ISO/IEC 17020:2012 Conformity assessment -- Re-
quirements for the operation of various types of
bodies performing inspection
• ISO/IEC 17021:2011 Conformity assessment -- Re-
quirements for bodies providing audit and certifica-
tion of management systems
• ISO/IEC TS 17021-2:2012 Conformity as-
sessment -- Requirements for bodies providing
audit and certification of management systems
-- Part 2: Competence requirements for au-
diting and certification of environmental man-
agement systems
• ISO/IEC TS 17021-3:2013 Conformity as-
sessment -- Requirements for bodies provid-
ing audit and certification of management sys-tems -- Part 3: Competence requirements for
auditing and certification of quality manage-
ment systems
• ISO/IEC TS 17021-4:2013 Conformity as-
sessment -- Requirements for bodies provid-
ing audit and certification of management sys-
tems -- Part 4: Competence requirements for
auditing and certification of event sustainabil-
ity management systems
• ISO/IEC TS 17021-5:2014 Conformity as-
sessment -- Requirements for bodies provid-
ing audit and certification of management sys-tems -- Part 5: Competence requirements for
auditing and certification of asset management
systems
• ISO/IEC TS 17022:2012 Conformity assessment --
Requirements and recommendations for content of
a third-party audit report on management systems
• ISO/IEC TS 17023:2013 Conformity assessment --
Guidelines for determining the duration of manage-
ment system certification audits
• ISO/IEC 17024:2003 Conformity assessment –General requirements for bodies operating certifica-
tion of persons
Page 21
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 21/27
21
• ISO/IEC 17025:2005 General requirements for the
competence of testing and calibration laboratories
• ISO 17088:2012 Specifications for compostable
plastics
•
ISO 17202 Textiles – Determination of twist in sin-gle spun yarns – Untwist/retwist method
• ISO/PAS 17506 Industrial automation systems and
integration – COLLADA digital asset schema spec-
ification for 3D visualization of industrial data
• ISO 17776 Petroleum and natural gas industries –
Offshore production installations – Guidelines on
tools and techniques for hazard identification and
risk assessment
• ISO 17799 - Code of Practice for Information Secu-
rity Management (superseded by ISO/IEC 27002)
• ISO 17894 Ships and marine technology – Com-
puter applications – General principles for the de-
velopment and use of programmable electronic sys-
tems in marine applications
• ISO/IEC 18000 Information technology – Radio
frequency identification for item management
• ISO/IEC 18000-1 Reference architecture and
definition of parameters to be standardized
• ISO/IEC 18000-2 Parameters for air interface
communications below 135 kHz• ISO/IEC 18000-3 Parameters for air interface
communications at 13,56 MHz
• ISO/IEC 18000-4 Parameters for air interface
communications at 2,45 GHz
• ISO/IEC 18000-6 Parameters for air interface
communications at 860 MHz to 960 MHz
• ISO/IEC 18000-7 Parameters for active air in-
terface communications at 433 MHz
• ISO/IEC 18004 Information technology – Auto-
matic identification and data capture techniques –
QR Code 2005 bar code symbology specification
• ISO/IEC 18009 Information technology – Program-
ming languages – Ada: Conformity assessment of a
language processor
• ISO/IEC 18013 Information technology – Personal
identification – ISO-compliant driving license
• ISO/IEC 18013-1:2005 Physical characteris-
tics and basic data set
• ISO/IEC 18013-2:2008 Machine-readable
technologies• ISO/IEC 18013-3:2009 Access control, au-
thentication and integrity validation
• ISO/IEC 18014 Information technology – Security
techniques – Time-stamping services
• ISO/IEC 18023 Information technology – SEDRIS
• ISO/IEC 18023-1:2006 Functional specifica-
tion
• ISO/IEC 18023-2:2006 Abstract transmittal
format
• ISO/IEC 18023-3:2006 Transmittal format
binary encoding
• ISO/IEC 18024-4:2006 Information technology –
SEDRIS language bindings – Part 4: C
• ISO/IEC 18025:2005 Information technology – En-
vironmental Data Coding Specification (EDCS)
• ISO/IEC 18026 Information technology – Spatial
Reference Model (SRM)
• ISO/IEC 18033 Information technology – Security
techniques – Encryption algorithms
• ISO/IEC 18033-1 General
• ISO/IEC 18033-2 Asymmetric ciphers
• ISO/IEC 18033-3 Block ciphers
• ISO/IEC 18033-4 Stream ciphers
• ISO/IEC 18041-4 Information technology – Com-
puter graphics, image processing and environmen-
tal data representation – Environmental Data Cod-
ing Specification (EDCS) language bindings – Part4: C
• ISO/IEC 18042-4:2006 Information technology –
Computer graphics and image processing – Spatial
Reference Model (SRM) language bindings – Part
4: C
• ISO/IEC 18092 Information technology – Telecom-
munications and information exchange between sys-
tems – Near Field Communication – Interface and
Protocol (NFCIP-1)
•
ISO 18117:2009 Surface chemical analysis – Han-dling of specimens prior to analysis
• ISO 18118:2004 Surface chemical analysis - Auger
electron spectroscopy and X-ray photoelectron
spectroscopy - Guide to the use of experimentally
determined relative sensitivity factors for the quan-
titative analysis of homogeneous materials
• ISO/TS 18152 Ergonomics of human-system inter-
action – Specification for the process assessment of
human-system issues
• ISO 18185 Freight containers – Electronic seals
• ISO 18245 Retail financial services – Merchant cat-
egory codes
Page 22
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 22/27
22 7 ISO 15000 – ISO 19999
• ISO/TR 18529:2000 Ergonomics – Ergonomics of
human-system interaction – Human-centred lifecy-
cle process descriptions
• ISO 18541 Road vehicles – Standardized access
to automotive repair and maintenance information
(RMI)
• ISO 18629 Industrial automation systems and inte-
gration – Process specification language
• ISO 19005 Document management – Electronic
document file format for long-term preservation
• ISO 19011:2011 Guidelines for auditing
management systems
• ISO 19092 Financial services – Biometrics – Secu-
rity framework
•
ISO 19101 Geographic information – Referencemodel
• ISO/TS 19103 Geographic information – Concep-
tual schema language
• ISO/TS 19104 Geographic information – Terminol-
ogy
• ISO 19105 Geographic information – Conformance
and testing
• ISO 19106 Geographic information – Profiles
•
ISO 19107 Geographic information – Spatialschema
• ISO 19108 Geographic information – Temporal
schema
• ISO 19109 Geographic information – Rules for ap-
plication schema
• ISO 19110 Geographic information – Methodology
for feature cataloguing
• ISO 19111 Geographic information – Spatial refer-
encing by coordinates
• ISO 19112 Geographic information – Spatial refer-
encing by geographic identifiers
• ISO 19113 Geographic information – Quality prin-
ciples
• ISO 19114 Geographic information – Quality eval-
uation procedures
• ISO 19115 Geographic information – Metadata
• ISO 19116 Geographic information – Positioning
services
• ISO 19117 Geographic information – Portrayal
• ISO 19118 Geographic information – Encoding
• ISO 19119 Geographic information – Services
• ISO/TR 19120 Geographic information – Func-
tional standards
• ISO/TR 19121 Geographic information – Imagery
and gridded data
• ISO/TR 19122 Geographic information / Geomatics
– Qualification and certification of personnel
• ISO 19123 Geographic information – Schema for
coverage geometry and functions
• ISO 19125 Geographic information – Simple fea-
ture access
• ISO 19126 Geographic information – Feature con-
cept dictionaries and registers
• ISO/TS 19127 Geographic information – Geodeticcodes and parameters
• ISO 19128 Geographic information – Web map
server interface
• ISO/TS 19129 Geographic information – Imagery,
gridded and coverage data framework
• ISO/TS 19130 Geographic information – Imagery
sensor models for geopositioning
• ISO 19131 Geographic information – Data product
specifications
• ISO 19132 Geographic information – Location-
based services – Reference model
• ISO 19133 Geographic information – Location-
based services – Tracking and navigation
• ISO 19134 Geographic information – Location-
based services – Multimodal routing and navigation
• ISO 19135 Geographic information – Procedures
for item registration
•
ISO 19136 Geographic information – GeographyMarkup Language (GML)
• ISO 19137 Geographic information – Core profile
of the spatial schema
• ISO/TS 19138 Geographic information – Data qual-
ity measures
• ISO/TS 19139 Geographic information – Metadata
– XML schema implementation
• ISO 19141 Geographic information – Schema for
moving features
• ISO 19142 Geographic information – Web Feature
Service
Page 23
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 23/27
23
• ISO 19143 Geographic information – Filter encod-
ing
• ISO 19144 Geographic information – Classification
systems
• ISO 19146 Geographic information – Cross-domain
vocabularies
• ISO 19156 Geographic information - Observations
and measurements
• ISO 19439 Enterprise integration – Framework for
enterprise modelling
• ISO 19440 Enterprise integration – Constructs for
enterprise modelling
• ISO/IEC 19501 Information technology – Open
Distributed Processing – Unified Modeling Lan-
guage (UML) Version 1.4.2
• ISO/IEC 19502 Information technology – Meta Ob-
ject Facility (MOF)
• ISO/IEC 19503 Information technology – XML
Metadata Interchange (XMI)
• ISO/IEC 19752 Information technology – Method
for the determination of toner cartridge yield for
monochromatic electrophotographic printers and
multi-function devices that contain printer compo-
nents
• ISO/IEC 19757 Information technology –Document Schema Definition Languages (DSDL)
• ISO/IEC 19757-2 Regular-grammar-based
validation – RELAX NG
• ISO/IEC 19757-3 Rule-based validation –
Schematron
• ISO/IEC 19757-4 Namespace-based Valida-
tion Dispatching Language (NVDL)
• ISO/IEC 19770 Information technology – Software
asset management
• ISO/IEC 19785 Information technology – Common
Biometric Exchange Formats Framework
• ISO/IEC 19788 Information technology – Learning,
education and training – Metadata for learning re-
sources
• ISO/IEC 19790 Information technology – Se-
curity techniques – Security requirements for
cryptographic modules
• ISO/IEC 19793 - Open Distributed Processing --
Use of UML for ODP system specifications
• ISO/IEC 19794 Information technology – Biomet-
ric data interchange formats
• ISO/IEC 19794-1:2011 Framework
• ISO/IEC 19794-2:2005 Finger minutiae data
• ISO/IEC 19794-3:2006 Finger pattern spec-
tral data
• ISO/IEC 19794-4:2005 Finger image data
• ISO/IEC 19794-5:2005 Face image data
• ISO/IEC 19794-6:2005 Iris image data
• ISO/IEC 19794-7:2007 Signature/sign time
series data
• ISO/IEC 19794-8:2006 Finger pattern skeletal
data
• ISO/IEC 19794-9:2007 Vascular image data
• ISO/IEC 19794-10:2007 Hand geometry sil-
houette data
8 ISO 20000 – ISO 29999
• ISO/IEC 20000 Information technology – Service
management
• ISO 20022 Financial services – UNIversal Financial
Industry message scheme
• ISO 20653 Road vehicles - Degrees of protec-
tion (IP-Code) - Protection of electrical equipment
against foreign objects, water and access
• ISO/IEC TR 20943 Information technology – Pro-cedures for achieving metadata registry content con-
sistency
• ISO/IEC TR 20943-1:2003 Data elements
• ISO/IEC TR 20943-3:2004 Value domains
• ISO/IEC 21000 Information technology – Multime-
dia framework (MPEG-21)
• ISO/IEC 21481 Information technology – Telecom-
munications and information exchange between sys-
tems – Near Field Communication Interface and
Protocol −2 (NFCIP-2)
• ISO 21482 Ionizing-radiation warning –
Supplementary symbol
• ISO 21500 Guidance on project management
• ISO 22000:2005 Food safety management systems
– Requirements for any organization in the food
chain
• ISO/TS 22002 Prerequisite programmes on food
safety
• ISO/TS 22002-1:2009 Prerequisite pro-grammes on food safety – Part 1: Food
manufacturing
Page 24
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 24/27
24 8 ISO 20000 – ISO 29999
• ISO/TS 22002-2:2013 Prerequisite pro-
grammes on food safety – Part 2: Catering
• ISO/TS 22002-3:2011 Prerequisite pro-
grammes on food safety – Part 3: Farming
• ISO/TS 22003:2013 Food safety management sys-
tems – Requirements for bodies providing audit andcertification of food safety management systems
• ISO 22004:2014 Food safety management systems
– Guidance on the application of ISO 22000
• ISO 22005:2007 Traceability in the feed and food
chain – General principles and basic requirements
for system design and implementation
• ISO 22093 Industrial automation systems and in-
tegration – Physical device control – Dimensional
Measuring Interface Standard (DMIS)
• ISO 22241 Diesel engines – NOx reduction agent
AUS 32
• ISO 22241-1 Quality requirements
• ISO 22241-2 Test methods
• ISO 22241-3 Handling, transportation and
storing
• ISO/IEC TR 22250 Information technology –
Document description and processing languages –
Regular Language Description for XML (RELAX)
• ISO/IEC TR 22250-1:2002 RELAX Core
• ISO 22301:2012 Societal security – Business conti-
nuity management systems – Requirements
• ISO/PAS 22399:2007 Societal security – Guideline
for incident preparedness and operational continuity
management
• ISO 22716:2007 Cosmetics – Good Manufacturing
Practices (GMP) – Guidelines on Good Manufac-
turing Practices
• ISO/IEC 23003 Information technology – MPEG
audio technologies
• ISO/IEC 23003-1 MPEG Surround
• ISO/IEC 23003-2 Spatial Audio Object Cod-
ing (SAOC)
• ISO/IEC 23270 Information technology – Program-
ming languages – C#
• ISO/IEC 23271 Information technology – Common
Language Infrastructure (CLI)
• ISO/IEC 23360 Linux Standard Base (LSB) core
specification 3.1
• ISO/IEC 23360-1 Generic specification
• ISO/IEC 23360-2 Specification for IA32 ar-
chitecture
• ISO/IEC 23360-3 Specification for IA64 ar-
chitecture
• ISO/IEC 23360-4 Specification for AMD64
architecture• ISO/IEC 23360-5 Specification for PPC32 ar-
chitecture
• ISO/IEC 23360-6 Specification for PPC64 ar-
chitecture
• ISO/IEC 23360-7 Specification for S390 ar-
chitecture
• ISO/IEC 23360-8 Specification for S390X ar-
chitecture
• ISO 23733 Textiles – Chenille yarns – Test method
for the determination of linear density
• ISO 23950 Information and documentation – Infor-
mation retrieval (Z39.50) – Application service def-
inition and protocol specification
• ISO/IEC 24707:2007 Information technology –
Common Logic (CL): a framework for a family of
logic-based languages
• ISO/IEC 24727 Identification cards – Integrated cir-
cuit card programming interfaces
• ISO/IEC 24727-1 Architecture
•
ISO/IEC 24727-2 Generic card interface• ISO/IEC 24727-3 Application interface
• ISO/IEC 24727-4 Application programming
interface (API) administration
• ISO/IEC 24727-5 Testing procedures
• ISO/IEC 24727-6 Registration authority pro-
cedures for the authentication protocols for in-
teroperability
• ISO/IEC 24744:2007 Software Engineering –
Metamodel for Development Methodologies
• ISO/IEC TR 24748:2010 Systems and software en-gineering - Life cycle management
• ISO/IEC 24762:2008 Information technology – Se-
curity techniques – Guidelines for information and
communications technology disaster recovery ser-
vices
• ISO 26000 Guidance on social responsibility
• ISO/IEC 26300 Information technology – Open
Document Format for Office Applications
(OpenDocument) v1.0
• ISO/IEC 27000 Information technology – Securitytechniques – Information security management sys-
tems – Overview and vocabulary
Page 25
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 25/27
25
• ISO/IEC 27001 Information technology – Security
techniques – Information security management sys-
tems – Requirements
• ISO/IEC 27002 Information technology – Security
techniques – Code of practice for information secu-
rity management
• ISO/IEC 27003 Information technology – Security
techniques – Information security management sys-
tem implementation guidance
• ISO/IEC 27004 Information technology – Security
techniques – Information security management –
Measurement
• ISO/IEC 27005 Information technology – Security
techniques – Information security risk management
• ISO/IEC 27006 Information technology – Security
techniques – Requirements for bodies providing au-dit and certification of information security manage-
ment systems
• ISO/IEC 27011 Information technology – Secu-
rity techniques – Information security manage-
ment guidelines for telecommunications organiza-
tions based on ISO/IEC 27002
• ISO/IEC 27037:2012 Information technology – Se-
curity techniques – Guidelines for identification,
collection, acquisition and preservation of digital ev-
idence
• ISO/TS 27687:2008 Nanotechnologies – Terminol-ogy and definitions for nano-objects – Nanoparticle,
nanofibre and nanoplate
• ISO 27799:2008 Health informatics -- Informa-
tion security management in health using ISO/IEC
27002
• ISO 28000 Specification for security management
systems for the supply chain
• ISO 28001:2007 Security management systems for
the supply chain – Best practices for implementing
supply chain security, assessments and plans – Re-quirements and guidance
• ISO 28003 Security management systems for the
supply chain – Requirements for bodies providing
audit and certification of supply chain security man-
agement systems
• ISO 28004 Security management systems for the
supply chain – Guidelines for the implementation of
ISO 28000
• ISO/PAS 28007:2012 Ships and marine technology
-- Guidelines for Private Maritime Security Compa-
nies (PMSC) providing privately contracted armedsecurity personnel (PCASP) on board ships (and pro
forma contract)
• ISO 28300:2008 Petroleum, petrochemical and nat-
ural gas industries – Venting of atmospheric and
low-pressure storage tanks
• ISO/IEC 29119 Software and systems engineering
– Software testing
• ISO/IEC 29500 Information technology – Docu-
ment description and processing languages – Office
Open XML File Formats
• ISO/IEC 29500-1 Fundamentals and Markup
Language Reference
• ISO/IEC 29500-2 Open Packaging Conven-
tions
• ISO/IEC 29500-3 Markup Compatibility and
Extensibility
• ISO/IEC 29500-4 Transitional Migration Fea-
tures
9 ISO 30000 – ISO 39999
• ISO 30000:2009 Ships and marine technology –
Ship recycling management systems – Specifica-
tions for management systems for safe and environ-
mentally sound ship recycling facilities
• ISO 31000:2009 Risk management – Principles and
guidelines
• ISO/IEC 31010:2009 Risk management - Risk as-sessment techniques
• ISO 32000 Document management – Portable doc-
ument format
• ISO/IEC 38500:2008 Corporate governance of in-
formation technology
10 ISO 50000 - ISO 59999
• ISO 50001:2011 Energy management systems – Re-
quirements with guidance for use
• ISO 55000:2014 Asset management – Overview,
principles and terminology
11 ISO 80000
• ISO/IEC 80000 Quantities and units
• ISO/TS 80004 Nanotechnologies – Vocabulary
• ISO/TS 80004-1 Core terms
• ISO/TS 80004-3 Carbon nano-objects
• ISO/TS 80004-4 Nanostructured materials
Page 26
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 26/27
26 15 EXTERNAL LINKS
• ISO/TS 80004-5 Nano/bio interface
• ISO/TS 80004-7 Diagnostics and therapeutics
for healthcare
12 See also• International Classification for Standards
• List of ASTM International standards
• List of DIN standards
• List of EN standards
• List of IEC standards
13 Notes
[1] This list generally excludes draft or withdrawn versions.
[2] ISO deliverables include “specifications” (ISO/PAS,
ISO/TS), “reports” (ISO/TR), etc, which are not referred
to by ISO as “standards”.
[3] The exact wording of this title varies between parts. This
is the wording of the most recently published part.
14 References
[1] “Standards catalog”. ISO.
[2] “Freely Available Standards”. ISO.
15 External links
• International Organization for Standardization
Page 27
7/21/2019 List of International Organization for Standardization Standards
http://slidepdf.com/reader/full/list-of-international-organization-for-standardization-standards-56dd4d2f4ae30 27/27
27
16 Text and image sources, contributors, and licenses
16.1 Text
• List of International Organization for Standardization standards Source: http://en.wikipedia.org/wiki/List_of_International_Organization_for_Standardization_standards?oldid=663648917 Contributors: Eclecticology, Dch, SJK, Ant, Comte0, Edward, Dante
Alighieri, Nixdorf, Mic, Mgimpel~enwiki, Kaihsu, Wael Ellithy, Tobias Conradi, ZeWrestler, Topbanana, Jusjih, PuzzletChung, Phil
Boswell, Rogper~enwiki, Robbot, Vespristiano, Nurg, Puckly, Wereon, Jor, Guy Peters, MikeCapone, Alan Liefting, David Gerard, John-
josephbachir, TDC, Michael Devore, Markus Kuhn, Dmb000006, CyborgTosser, Cantus, LarryGilbert, Uzume, Hananeko, Karl-Henner,The number c, Thorwald, Kate, Danh, Bcordes, Omassey, CALR, Rich Farmbrough, Rhobite, Mecanismo, ArnoldReinhold, Michael Zim-
mermann, Orbitalia, Hhielscher, Elwikipedista~enwiki, Quinobi, Nrbelex, AnyFile, Smalljim, Duk, Foobaz, Arcadian, MARQUIS111,
Minghong, Nsaa, Foxandpotatoes, Mdd, ClementSeveillac, Gary, Typhlosion, Krischik, Phoenix orb, Kernoz, Anamanfan, Lothartklein,Forderud, Kelly Martin, Steven Luo, Gheesh, Donpdonp, Koavf, FayssalF, Zarano, Lmatt, Physchim62, DMahalko, Sasuke Sarutobi,
Dr Shorthair, Gaius Cornelius, Legalize, Anomalocaris, Vanished user kjdioejh329io3rksdkj, Jpbowen, BertK, HHHH, Caerwine, John-
drinkwater, Sagsaw, Open2universe, Lt-wiki-bot, Rwwww, SmackBot, Elonka, CesarGon, Gilliam, Bluebot, DStoykov, CSWarren, Let-dorf, New World Man, Khukri, Zimage, PetesGuide, Wirbelwind, Tompsci, Mwtoews, RayGates, Srbradbury, Thebt, Guroadrunner,
Simongraham, Burt Harris, Alan.Ewing, Peter Horn, Wizard191, Xsmith, MyKey~enwiki, Yendor1958, CmdrObot, Baiji, AndrewHowse,
Cydebot, Zginder, Luccas, Bookgrrl, AstroPig7, סרפ , Thijs!bot, Alkari, Anupam, Bobblehead, Humphs, Miller17CU94, Visik, Mende-
livia~enwiki, Rsocol, Macadk, D99figge, Veeliam, AlephGamma, Roberth Edberg, Onigame, Gwern, MartinBot, Nono64, Mausy5043,Pazmanpro, DASonnenfeld, VolkovBot, Perohanych, JPaulClark, Serdelll, Andy Dingley, Mocu, SieBot, Jerryobject, Pedro.haruo, RW
Marloe, Radartooth3, Tornadox, ClueBot, Gene93k, Namazu-tron, Kmstock, Arjayay, AJStadlin, DumZiBoT, Iest5005, Environ1561,
Mitch Ames, Somineu, MystBot, Addbot, Catafalque, Ghettoblaster, TotalCommunication, Harish431, SpillingBot, Favonian, Borio1704,
Function95, Mjquinn id, Slgcat, Sven Boisen, Luckas-bot, Fraggle81, TaBOT-zerem, Carla.antonini~enwiki, KamikazeBot, 4th-otaku,Taiwan.louis.lu, GB fan, Frankenpuppy, Rehansaccount, Xqbot, Drilnoth, Radack, Rkov, Nasa-verve, Taflinem, Kinclli, DocMeromor-
phic, Hourswhom, In fact, Theifynia, Hench2008, DenMoren, DrilBot, Guigouz, Supergreg no1, Lineslarge, Patrik Roth~enwiki, Kblaubaer, Lotje, Yorken~enwiki, Ato 01, EmausBot, Pinji, K6ka, Gedman2, Shmilyshy, Andattaca2010, SBaker43, Matthiaspaul, Satel-
lizer, Sougata.bhattacharya, Risk Engineer, URSINDIA, Pre-searcher, AllenZh, NlightN8R, YFdyh-bot, SoledadKabocha, Sven Linow,
ArmbrustBot, RedZay7, Navinfrancis, PlamZ, Doktor Oz, Guxsousa, Lover amethyst and Anonymous: 184
16.2 Images
• File:Folder_Hexagonal_Icon.svg Source: https://upload.wikimedia.org/wikipedia/en/4/48/Folder_Hexagonal_Icon.svg License: Cc-by-
sa-3.0 Contributors: ? Original artist: ?
16.3 Content license
• Creative Commons Attribution-Share Alike 3.0