-
List of DIN standards
DIN 1 to DIN 99
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 1 Cone Pins, untempered Withdrawn DIN EN 22339 ISO 2339
DIN 3 Standard measurements Withdrawn
DIN 5 Technical drawings - Axonometric projections, Isometric
projection Withdrawn
DIN ISO 5456-1, DIN ISO 5456-2, DIN ISO 5456-3, DIN ISO
5456-4
ISO 5456-1, ISO 5456-2, ISO 5456-3, ISO 5456-4
DIN 5-10 Technical drawings - projections, terms Withdrawn DIN
ISO 10209-2 ISO 10209-2
DIN 6 Projection displays in Normal, views and special
presentations Withdrawn DIN ISO 128, DIN EN ISO 128 ISO 128
DIN 7 Parallel Pins Withdrawn DIN EN ISO 2338 ISO 2338
DIN 11 Whitworth pipe threads 1/4"-6" Thread diameter, sizes,
teaching information
Withdrawn
DIN 13-1
ISO general purpose metric screw threads - Part 1: Nominal sizes
for coarse pitch threads; nominal diameter from 1 mm to 68 mm
Active
DIN 13-2 ISO general purpose metric screw threads - Part 2:
Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads;
nominal diameter from
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
1 mm to 50 mm
DIN 13-3
ISO general purpose metric screw threads - Part 3: Nominal sizes
for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90
mm
Active
DIN 13-4
ISO general purpose metric screw threads - Part 4: Nominal sizes
for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110
mm
Active
DIN 13-5
ISO general purpose metric screw threads - Part 5: Nominal sizes
for 1 mm and 1,25 mm fine pitch threads; nominal diameter from 7,5
mm to 200 mm
Active
DIN 13-6
ISO general purpose metric screw threads - Part 6: Nominal sizes
for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300
mm
Active
DIN 13-7
ISO general purpose metric screw threads - Part 7: Nominal sizes
for 2 mm fine pitch threads; nominal diameter from 17 mm to 300
mm
Active
DIN 13-8
ISO general purpose metric screw threads - Part 8: Nominal sizes
for 3 mm fine pitch threads; nominal diameter from 28 mm to 300
mm
Active
DIN 13-9
ISO general purpose metric screw threads - Part 9: Nominal sizes
for 4 mm fine pitch threads; nominal diameter from 40 mm to 300
mm
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 13-10
ISO general purpose metric screw threads - Part 10: Nominal
sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to
500 mm
Active
DIN 13-11
ISO general purpose metric screw threads - Part 11: Nominal
sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to
1000 mm
Active
DIN 13-12
ISO general purpose metric screw threads - Part 12: 1 to 300 mm
diameter coarse and fine pitch threads Selected diameters and
pitches
Active
DIN 13-13
ISO general purpose metric screw threads - Part 13: Selected
sizes for screws, bolts and nuts from 1 to 52 mm screw thread
diameter and limits of sizes
Active
DIN 13-19 ISO general purpose metric screw threads - Part 19:
Nominal profiles Active
DIN 13-20
ISO general purpose metric screw threads - Part 20: Limits of
sizes for coarse pitch threads with the preferred tolerance
classes; nominal sizes from 1 mm to 68 mm
Active
DIN 13-21
ISO general purpose metric screw threads - Part 21: Limits of
sizes for fine pitch threads with the preferred tolerance classes;
Nominal diameter from 1 mm to 24,5 mm
Active
DIN 13-22 ISO general purpose metric screw threads - Part 22:
Limits of sizes for
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
fine pitch threads with the preferred tolerance classes; Nominal
diameter from 25 mm to 52 mm
DIN 13-23
ISO general purpose metric screw threads - Part 23: Limits of
sizes for fine pitch threads with the preferred tolerance classes;
Nominal diameter from 53 mm to 110 mm
Active
DIN 13-24
ISO general purpose metric screw threads - Part 24: Limits of
sizes for fine pitch threads with the preferred tolerance classes;
Nominal diameter from 112 mm to 180 mm
Active
DIN 13-25
ISO general purpose metric screw threads - Part 25: Limits of
sizes for fine pitch threads with the preferred tolerance classes;
Nominal diameter from 182 mm to 250 mm
Active
DIN 13-26
ISO general purpose metric screw threads - Part 26: Limits of
sizes for fine pitch threads with the preferred tolerance classes;
Nominal diameter from 252 mm to 1000 mm
Active
DIN 13-28
ISO general purpose metric screw threads - Part 28: Coarse and
Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root
Cross-sections, Tensile Stress Cross-sections and Pitch Angles
Active
DIN 13-50
ISO general purpose metric screw threads - Part 50: Combination
of tolerance classes for formed internal screw threads
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 13-51
ISO general purpose metric screw threads - Part 51: External
screw threads for transition fits (former: screw threads for
interference fit); tolerances, limit deviations, limits of
sizes
Active
DIN 13-52 ISO general purpose metric screw threads - Part 52:
Multi-start thread tolerances and deviation of profile
Active
DIN 16 Oblique Standard Typeface for Drawings Withdrawn
DIN 17 Upright Standard Typeface for Drawings Withdrawn
DIN 76-1 Thread run-outs and thread undercuts for ISO metric
threads in accordance with DIN 13-1
Active
DIN 76-2 Thread run-outs and thread undercuts for pipe threads
conforming to ISO 228 part 1
Active
DIN 76-3
Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and
Knuckle Threads and other Threads of Coarse Pitch
Active
DIN 78 Protrusions of bolt ends Active
DIN EN ISO 4753 (governs thread ends for bolts assembled with
hexagon slotted nuts)
ISO 4753
DIN 84 Product grade A slotted cheese head Withdrawn DIN EN ISO
1207 ISO 1207
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
screws
DIN 85 Product grade A slotted pan head screws Withdrawn DIN EN
ISO 1580 ISO 1580
DIN 93 Tab washers with long tab Withdrawn DIN EN ISO 1234 ISO
1234
DIN 94 Split pins Withdrawn DIN EN ISO 1234 ISO 1234
DIN 95 Slotted Raised Countersunk (Oval) Head Wood Screws
Active
DIN 96 Slotted Round Head Wood Screws Active
DIN 100 to DIN 199
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 103-1 ISO Metric Trapezoidal Screw Thread; Profiles
DIN 103-2 ISO Metric Trapezoidal Screw Thread; General Plan
DIN 103-3
ISO Metric Trapezoidal Screw Thread; Allowances and Tolerances
for Trapezoidal Screw Threads of General Purpose
DIN 103-4 ISO Metric Trapezoidal Screw Thread; Nominal
Dimensions
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 103-5
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut
Threads from 8 to 100 mm Nominal Diameter
DIN 103-6
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut
Threads from 105 to 300 mm Nominal Diameter
DIN 103-7
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt
Threads from 8 to 100 mm Nominal Diameter
DIN 103-8
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt
Threads from 105 to 300 mm Nominal Diameter
DIN 103-9
ISO metric trapezoidal screw threads; gauging of external and
internal threads; gauge dimensions and design features
DIN V 105-1 Clay masonry units - Part 1: Solid and hollow bricks
with density classes of 1,2
Withdrawn DIN V 105-100, DIN EN 771-1 EN 771-1
DIN V 105-2 Clay masonry units - Part 2: Solid and hollow bricks
with density classes equal 1.0
Withdrawn DIN V 105-100, DIN EN 771-1 EN 771-1
DIN 105-3 Clay masonry units - Part 3: Tile and high
strength-high-strength clinker Withdrawn DIN V 105-100, DIN EN
771-1 EN 771-1
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 105-4 Clay masonry units - Part 4: Ceramic bricks Withdrawn
DIN V 105-100, DIN EN 771-1, DIN EN 772-7
EN 771-1, EN 772-7
DIN 105-5 Clay masonry units - Part 5: Lightweight long-hole
brick and light long-hole brick panels
Active
DIN V 105-6 Clay masonry units - Part 6: High precision units
Active
DIN V 105-100
Clay masonry units - Part 100: Clay masonry units with specific
properties Active
DIN 125 Washers; medium type, primarily for hexagon bolts
Withdrawn DIN EN ISO 7089, DIN EN ISO 7090
ISO 7089, ISO 7090
DIN 125-1 Product grade A washers - with a hardness up to 250 HV
designed for use with hexagon head bolts and nuts
Withdrawn DIN EN ISO 7089, DIN EN ISO 7090 ISO 7089, ISO
7090
DIN 125-2 Product grade A washers - with a hardness up to 300 HV
designed for use with hexagon head bolts and nuts
Withdrawn DIN EN ISO 7089, DIN EN ISO 7090 ISO 7089, ISO
7090
DIN 126 Product grade C washers - designed for use with hexagon
head bolts and nut
Withdrawn DIN EN ISO 7091 ISO 7091
DIN 127 Spring lock washers with square ends or tang ends
Withdrawn
DIN 128 Curved and wave spring lock washers Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 137 Spring washers, curved or wave Withdrawn
DIN 200 to DIN 299
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 201 Technical drawings; Hatchings; Representation of cutting
edges and materials
Withdrawn DIN ISO 128-50 ISO 128-50
DIN 209 Machine Reamers with Screwed-on Blades Active
DIN 267-1 Fasteners - Part 1: Technical delivery conditions;
General requirements Withdrawn
DIN 267-2
Fasteners - Part 2: Technical delivery conditions; Bolts,
Screws, Nuts and Similar Threaded and Formed Parts; Types and
Dimensional Accuracy
Active DIN EN ISO 4759-1 ISO 4759-1
DIN 267-3
Fasteners - Part 3: Technical delivery conditions; Property
classes for carbon steel and alloy steel bolts and screws;
Conversion of property classes
Withdrawn DIN EN ISO 898-1 ISO 898-1
DIN 267-4 Fasteners - Part 4: Technical delivery conditions;
Property classes for nuts (previous classes)
Withdrawn DIN EN ISO 898-2 ISO 898-2
DIN 267-5
Fasteners Part 5: Technical delivery conditions; Acceptance
inspection; modified version of ISO 3269, 1984 edition
Withdrawn DIN EN ISO 3269 ISO 3269
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 267-6 Fasteners - Part 6: Technical delivery conditions;
Designs and accuracy of measurement for product grade F
Active
DIN 267-7 Fasteners - Part 9: Technical delivery conditions;
Bolts made of unalloyed or low-alloy steels
Withdrawn DIN EN ISO 898-1 ISO 898-1
DIN 267-9 Fasteners - Part 9: Technical delivery conditions;
Components with Electroplated Coatings
Withdrawn DIN EN ISO 4042 ISO 4042
DIN 267-10 Fasteners - Part 10: Technical delivery conditions;
Hot dip galvanized parts Withdrawn DIN EN ISO 10684 ISO 10684
DIN 267-11 Fasteners - Part 11: Technical delivery conditions
(with additions to ISO 3506); Corrosion-resistant stainless steel
fasteners
Withdrawn
DIN 267-12 Fasteners - Part 12: Technical delivery conditions;
Self-tapping screws Withdrawn DIN EN ISO 2702 ISO 2702
DIN 267-13
Fasteners - Part 13: Technical delivery conditions; Components
for Bolted Connections Made Mainly from Materials Exhibiting a High
Impact Strength at Low Temperature or from Materials with a High
Temperature Strength
Active
DIN 267-15 Fasteners - Part 15: Technical delivery conditions;
Prevailing torque type nuts Withdrawn
DIN EN ISO 2320, DIN EN ISO 3506-1, DIN EN ISO 3506-2, DIN EN
ISO 3506-3
ISO 2320, ISO 3506-1, ISO 3506-2, ISO 3506-3
DIN 267-18 Fasteners - Part 18: Technical delivery conditions;
Components made of Non-
Withdrawn DIN EN 28839 ISO 8839
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
ferrous Metals
DIN 267-19 Fasteners - Part 19: Technical delivery conditions;
Surface discontinuities on bolts and screws
Withdrawn DIN EN ISO 26157-1, DIN EN ISO 26157-3 ISO 6157-1, ISO
6157-3
DIN 267-20 Fasteners - Part 20: Technical delivery conditions;
Surface discontinuities on nuts Withdrawn DIN EN ISO 6157-2, DIN EN
ISO 10484, DIN EN ISO 10485
ISO 6157-2, ISO 10484, ISO 10485
DIN 267-21 Fasteners - Part 21: Technical delivery conditions;
Widening test on nuts Withdrawn DIN EN ISO 6157-2, DIN EN ISO
10484, DIN EN ISO 10485
ISO 6157-2, ISO 10484, ISO 10485
DIN 267-23 Fasteners - Part 23: Technical delivery conditions;
Property classes for nuts with fine thread (ISO classes)
Withdrawn DIN EN ISO 898-6 ISO 898-6
DIN 267-24 Fasteners - Part 24: Technical delivery conditions;
Property classes for nuts (Hardness classes)
Active
DIN 267-25 Fasteners - Part 25: Technical delivery conditions;
Torsion testing of M1 to M10 bolts and screws
Withdrawn DIN EN 20898-7 EN 20898-7
DIN 267-26 Fasteners - Part 26: Technical delivery conditions;
Conical spring washers for bolt/nut assemblies
Active
DIN 267-27 Fasteners - Part 27: Technical specifications; Steel
screws, bolts and studs with adhesive coating
Active
DIN 267-28 Fasteners - Part 28: Technical specifications; Steel
screws, bolts and
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
studs with locking coating
DIN 267-29
Fasteners - Part 29: Technical specifications; Product grades
for parts for bolted connections for use at temperatures ranging
from -200C to +700C
Withdrawn
DIN 267-30 Fasteners - Part 30: Technical specifications; Metric
thread rolling screws of property class 10.9
Active
DIN 276-1 Building costs; Part 1: Building construction
Active
DIN 276-2 Building costs; Part 2: Classification of cost
Withdrawn
DIN 276-3 Building costs; Part 3: Ascertainment of cost
Withdrawn
DIN 300 to DIN 399
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 315 Wing nuts with rounded wings Active
DIN 316 Wing screws with rounded wings Active
DIN 323-1 Preferred Numbers and Series of Preferred Numbers;
Basic Values, Calculated Values, Rounded Values
Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 323-2 Preferred Numbers and Series of Preferred Numbers;
Introduction Active
DIN 332-1 60 centre holes; types R, A, B, and C Active
DIN 332-2 Center holes 60 with thread for shaft ends for
rotating electrical machines Active
DIN 332-4 Centre holes for rail vehicles axles Active
DIN 332-7 Machine tools; 60 centre holes; dimensioning
Active
DIN 332-8 Centre holes 90, form S; dimensions, determination
process Active
DIN 332-10 Center Holes; Indications on Technical Drawings
Withdrawn DIN ISO 6411 ISO 6411
DIN 338 Parallel shank twist drills, jobber series Active
DIN 400 to DIN 499
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 404 Slotted capstan screws Active
DIN 406-10 Engineering drawing practice; dimensioning; concepts
and general principles
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 406-11 Engineering drawing practice; dimensioning;
principles of application
Active
DIN 406-12
Engineering drawing practice; dimensioning; tolerancing of
linear and angular dimensions (modified version of ISO
406:1987)
Active
DIN 417 Slotted set screws with long dog point Withdrawn DIN EN
27435 ISO 7435
DIN 427 Slotted headless screws with chamfered end Withdrawn DIN
EN ISO 2342 ISO 2342
DIN 428 Hexagon nuts, Grade C Withdrawn DIN EN ISO 4034 ISO
4034
DIN 433 Washers for use with cheese head screws Withdrawn DIN EN
ISO 7092 ISO 7092
DIN 433-1 Product grade A washers - with a hardness up to 250 HV
designed for use with cheese head screws
Withdrawn DIN EN ISO 7092 ISO 7092
DIN 433-2 Product grade A washers - with a hardness up to 300 HV
designed for use with cheese head screws
Withdrawn DIN EN ISO 7092 ISO 7092
DIN 438 Slotted set screws with cup point Withdrawn DIN EN 27436
ISO 7436
DIN 439 Hexagon thin nuts Withdrawn DIN EN ISO 4035, DIN EN ISO
4036,DIN EN ISO 8675 ISO 4035, ISO 4036, ISO 8675
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 439-1 Unchamfered hexagon thin nuts - Product grade B
Withdrawn DIN EN ISO 4036 ISO 4036
DIN 439-2 Chamfered hexagon thin nuts - Product grades A and B
Withdrawn DIN EN ISO 4035, DIN EN ISO 8675 ISO 4035, ISO 8675
DIN 440 Washers for use in timber constructions Withdrawn DIN EN
ISO 7094 ISO 7094
DIN 444 Eyebolts Active
DIN 461 Graphical Representation in Systems of Coordinates
Active
DIN 462
Machine Tools; Internal Tab Washers for Slotted Round Nuts for
Hook Spanner according to DIN 1804
Active
DIN 464 Knurled thumb screws, high type Active
DIN 466 Knurled nuts, high type Active
DIN 467 Knurled nuts, low type Active
DIN 471 Circlips (retaining rings) for shafts; Normal type and
heavy type Active
DIN 476 Paper sizes Withdrawn DIN EN ISO 216 ISO 216
DIN 476-2 Trimmed Sizes of Paper - C Series Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 477
DIN 479 Square head bolts with short dog point Active
DIN 500 to DIN 599
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 522 Metal washers; technical delivery conditions Withdrawn
DIN EN ISO 4759-3 ISO 4759-3
DIN 548 Round nuts with set pin holes in side Active
DIN 551 Slotted set screws with flat point Withdrawn DIN EN
24766 ISO 4766
DIN 553 Slotted set screws with cone point Withdrawn DIN EN
27434 ISO 7434
DIN 555 M5 to M100x6 hexagon nuts - Product grade C Withdrawn
DIN EN ISO 4034 ISO 4034
DIN 558 Hexagon head screws Withdrawn DIN EN ISO 4018 ISO
4018
DIN 580 Collar eyebolts for lifting purposes Active
-
DIN 600 to DIN 699
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 601 M5 to M52 hexagon head bolts; product grade C Withdrawn
DIN EN ISO 4016 ISO 4016
DIN 603 Mushroom head square neck bolts Active
DIN 609 Hexagon fits bolts with long thread Active
DIN 625-1 Rolling bearings; single row radial contact ball
bearings Active
DIN 625-3 Rolling bearings; double row radial contact ball
bearings Active
DIN 625-4 Rolling bearings; radial contact groove ball bearings
with flanged outer ring Active
DIN 653 Knurled thumb screws, low type Active
DIN 678-1 Envelopes - Part 1: Sizes Active
DIN 678-2 Envelopes - Part 2: Envelopes for Processing in
Enveloping Machines, Size C6 to C4
Active
-
DIN 700 to DIN 799
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 763 Tested, non-calibrated, long-link round steel chains
Active
DIN 764-1 Calibrated and tested round steel link chains for
continuous conveyors; grade 2, pitch 3,5d
Active
DIN 764-2 Calibrated and tested round steel link chains for
continuous conveyors; grade 3, pitch 3,5d
Active
DIN 766 Calibrated and tested grade 3 round steel link chains
Active
DIN 799-1 Foundation Blocks Active
DIN 800 to DIN 899
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN12 820-1 Standards Work - Part 1: Principles Active
DIN 820-2 Standardization - Part 2: Presentation of standards;
examples for presentation of figures, tables and part lists
Active
DIN 820-3 Standardization - Pdfart 3: Concepts Active
DIN 820-4 Standardization - Part 4: Working procedure Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 820-11
Standardization - Part 11: Presentation of Standards concerning
safety regulations which are VDE-Specifications or
VDE-Guidelines
Active
DIN 820-12 Standardization - Part 12: Presentation of standards
concerning safety regulations Active
DIN 820-13
Standardization - Part 13: Adoption of European documents of
CEN, CENELEC and of ETSI; Concepts and presentation
Active
DIN 820-15
Standardization - Part 15: Implementation of ISO and IEC
international documents; Concepts and presentation
Active
DIN 820-120 Standardization - Part 120: Guidelines for the
inclusion of safety aspects in standards (ISO/IEC Guide
51:1999)
Active
DIN 824 Technical drawings; Folding to filing size Active
DIN 899 Hand Operated Wrenches and Sockets; Technical
Specifications Withdrawn DIN ISO 1711-1 ISO 1711-1
-
DIN 900 to DIN 999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 908 Hexagon socket screw plugs with parallel screw thread
Active
DIN 910 Hexagon-duty hexagon head screw plugs Active
DIN 911 Hexagon Socket Screw Keys Withdrawn DIN ISO 2936 ISO
2936
DIN 912 Hexagon socket head cap screws (modified version of ISO
4762) Withdrawn DIN EN ISO 4762, DIN EN ISO 21269
ISO 4762, ISO 21269
DIN 913 Hexagon socket set screws with flat point (ISO 4026
modified) Withdrawn DIN EN ISO 4026 ISO 4026
DIN 914 Hexagon socket set screws with cone point (ISO 4029
modified) Withdrawn DIN EN ISO 4027 ISO 4027
DIN 915 Hexagon socket set screws with full dog point Withdrawn
DIN EN ISO 4028 ISO 4028
DIN 916 Hexagon socket set screws with cup point (ISO 4029
modified) Withdrawn DIN EN ISO 4029 ISO 4029
DIN 918 Fasteners; Terminology; Spelling of terms; Abbreviations
Active
DIN 918-3 Overview of European Standards for fasteners
Active
DIN 919-1 Technical Drawings; Wood Processing; Principles
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 921 Slotted pan head screws with large head Active
DIN 923 Slotted pan head screws with shoulder Active
DIN 929 Hexagon weld nuts Active
DIN 930 Fine thread pitch partially threaded screws Withdrawn
DIN 931-1, DIN 931-2
DIN 931-1 M1,6 to M39 Hexagon Cap Screws Partially Threaded -
Product grades A and B
Withdrawn DIN EN ISO 4014 ISO 4014
DIN 931-2 M42 to M160x6 Hexagon Cap Screws Partially Threaded -
Product grade B Withdrawn DIN EN ISO 4014 ISO 4014
DIN 933 M1,6 to M52 Hexagon Cap Screws Fully Threaded - Product
grades A and B
Withdrawn DIN EN ISO 4017 ISO 4017
DIN 934 Hexagon nuts with metric coarse and fine pitch thread -
Product classes A and B
Withdrawn DIN EN ISO 4032, DIN EN ISO 8673 ISO 4032, ISO
8673
DIN 935-1 Hexagon slotted nuts and castle nuts with metric
coarse and fine pitch thread - Product grades A and B
Active
DIN 935-2 M42 to M160x6 hexagon head bolts; product grade B
Active
DIN 935-3 Hexagon slotted nuts with metric coarse pitch thread -
Product grade C Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 936 M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product
grades A and B
Withdrawn
DIN 937 Hexagon thin castle nuts Withdrawn
DIN 938 Studs with a length of engagement equal to about 1 d
Active
DIN 939 Studs with a length of engagement equal to about 1,25 d
Active
DIN 946 Determination of coefficient of friction of bolt/nut
assemblies under specified conditions
Withdrawn DIN EN ISO 16047 ISO 16047
DIN 960 M8x1 to M100x4 hexagon head bolts with fine pitch thread
- Product grades A and B
Withdrawn DIN EN ISO 8765, DIN EN ISO 8676 ISO 8765, ISO
8676
DIN 961 M8x1 to M52x3 hexagon head bolts with fine pitch thread
- Product grades A and B
Withdrawn DIN EN ISO 8676 ISO 8676
DIN 962 Designation system for fasteners Active
DIN 963 Slotted countersunk head screws (with countersunk heads
as specified in ISO 2009-1972)
Withdrawn DIN EN ISO 2009 ISO 2009
DIN 964 Slotted raised countersunk oval head screws Withdrawn
DIN EN ISO 2010 ISO 2010
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 965 Cross recessed countersunk flat head screws Withdrawn
DIN EN ISO 7046-1, DIN EN ISO 7046-2
ISO 7046-1, ISO 7046-2
DIN 966 Cross recessed raised countersunk head screws Withdrawn
DIN EN ISO 7047 ISO 7047
DIN 970 Hexagon nuts; Style 1; Metric coarse thread, Product
grades A and B; ISO 4032 modified
Withdrawn DIN EN ISO 4032 ISO 4032
DIN 971-1 Style 1 hexagon nuts with metric fine pitch thread;
property classes 6 and 8 Withdrawn DIN EN ISO 8673 ISO 8673
DIN 971-2 Style 2 hexagon nuts with metric fine pitch thread;
property classes 10 and 12 Withdrawn DIN EN ISO 8674 ISO 8674
DIN 972 M5 to M39 hexagon nuts; style 1; product grade C
(modified version of ISO 4034)
Withdrawn DIN EN ISO 4034 ISO 4034
DIN 975 Threaded rods Withdrawn
DIN 976-1 Metric thread stud bolts Active
DIN 976-2 Metric interference-fit thread stud bolts Active
DIN 977 Hexagon weld nuts with flange Withdrawn DIN EN ISO 21670
ISO 21670
DIN 979 Hexagon thin slotted nuts and castle nuts with metric
coarse and fine pitch thread - Product grades A and B
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 980 All-metal prevailing torque type hexagon nuts Withdrawn
DIN EN ISO 7042, DIN EN ISO 10513
ISO 7042, ISO 10513
DIN 981 Locknuts for use with rolling bearings Active
DIN 982 Prevailing torque type hexagon nuts with nonmetallic
insert Withdrawn DIN EN ISO 7040, DIN EN ISO 10512
ISO 7040, ISO 10512
DIN 983 Retaining rings with lugs for use on shafts (external
circlips) Active
DIN 985 Prevailing torque type hexagon thin nuts with
nonmetallic insert Withdrawn DIN EN ISO 10511 ISO 10511
DIN 988 Shim rings and supporting rings Active
DIN 1000 to DIN 1999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1025-1
Hot rolled I-sections - Part 1: Narrow flange I-sections,
I-serie - Dimensions, masses, sectional properties
Active
DIN 1025-2
Hot rolled I-beams - Part 2: Wide flange I-beams, IPB-serie;
dimensions, masses, sectional properties
Active
DIN 1025-3 Hot rolled I-beams; wide flange I-beams, light
pattern, IPBl-serie; dimensions, masses,
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
sectional properties
DIN 1025-4
Hot rolled I-beams; wide flange I-beams heavy pattern,
IPBv-serie; dimensions, masses, sectional properties
Active
DIN 1025-5
Hot rolled I-beams; medium flange I-beams, IPE-serie;
dimensions, masses, sectional properties
Active
DIN 1301-1 Units - Part 1: Names and Symbols Active
DIN 1301-2 Units - Part 2: Submultiples and Multiples for
General Use Active
DIN 1301-3 Units - Part 3: Conversions of Units No Longer To Be
Used Active
DIN 1302 General Mathematical Symbols and Concepts Active
DIN 1303 Vectors, matrices, tensors; symbols and concepts
Active
DIN 1304-1 Letter symbols for physical quantities - Part 1:
Symbols for general use
Active
DIN 1304-2
Letter symbols for physical quantities - Part 2: Symbols for use
in meteorology and geophysics
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1304-3
Letter symbols for physical quantities - Part 3: Symbols for use
in electric power engineering
Active
DIN 1304-5 Letter symbols for physical quantities - Part 5:
Symbols for use in fluid mechanics
Active
DIN 1304-8
Letter symbols for physical quantities - Part 9: Symbols for use
in the field of static converters using semiconductor devices
Active
DIN 1304-9
Letter symbols for physical quantities - Part 9: Symbols for
equivalent circuits of piezoelectric crystals
Active
DIN 1311-1
(Mechanical) vibrations, oscillations and vibration systems -
Part 1: Basic concepts, survey
Active
DIN 1311-2
(Mechanical) vibrations, oscillations and vibration systems -
Part 2: Linear vibration systems with single degree of freedom
Active
DIN 1311-3
(Mechanical) vibrations, oscillations and vibration systems -
Part 3: Linear time-invariant vibration systems with a finite
number of degrees of freedom
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1311-4 Vibration; Vibrating Continua, Waves Active
DIN 1313 Physical Quantities and Equation; Concepts, Methods of
Writing
Active
DIN 1315 Angle; Concepts, Units Active
DIN 1318 DIN 1324-1 Electromagnetic Field - Part 1. State
Quantities
Active
DIN 1324-2 Electromagnetic Field - Part 2. Material Quantities
Active
DIN 1324-3 Electromagnetic Field - Part 3. Electromagnetic Waves
Active
DIN 1325-1
Vocabulary for value management, value analysis and functional
analysis - Part 1: Value analysis and functional analysis
Active
DIN 1325-2
Value Management, Value Analysis, Functional Analysis Vocabulary
- Part 2: Value Management
Active
DIN 1332 Acoustics; Symbols Withdrawn DIN EN ISO 80000-8 ISO
80000-8
DIN 1333 Presentation of Numerical Data Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1338 Writing and Typesetting of Formulae Active
DIN 1355-1 Time; Calendar, Numbering of Weeks, Date of Day,
(Clock) Time
Withdrawn
DIN 1421 Arrangement and Numbering in Texts; Clauses,
Paragraphs, Enumerations
Active
DIN 1422-1
Publications in Sciences, Technology, Economy and
Administration; Presentation of Manuscripts and Typoscripts
Active
DIN 1422-2
Publications in Sciences, Technology, Economy and
Administration; Presentation of Clean Copies for Reprographic
Use
Active
DIN 1422-3
Publications in Sciences, Technology, Economy and
Administration; Typographical Presentation
Active
DIN 1422-4
Publications in Sciences, Technology, Economy and
Administration; Presentation of Scientific and Technical
Reports
Active
DIN 1440 Medium type washers for pins Withdrawn DIN EN 28738 ISO
8738
DIN 1443 Clevis pins without head Withdrawn DIN EN 22340 ISO
2340
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1444 Clevis pins with head Withdrawn DIN EN 22341 ISO
2341
DIN 1450 Legibility of Typefaces General Active
DIN 1451-1 Lettering - Linear-Antiqua without serifes General
Active
DIN 1451-2 Typefaces - lineal Linear-Antiqua; lettering for
transportation
Active
DIN 1451-3 Lettering - Linear-Antiqua without serifes; lettering
for printing
Active
DIN 1451-4 Typefaces - lineal Linear-Antiqua; stenciled
lettering for engraving and other processes
Active
DIN 1463-1
Guidelines for the Establishment and Development of Thesauri;
Monolingual Thesauri
Active
DIN 1463-2
Guidelines for the Establishment and Development of Thesauri;
Multilingual Thesauri
Active
DIN 1470 Grooved Pins, Full Length Parallel-grooved with Pilot
Withdrawn DIN EN 8739 ISO 8739
DIN 1471 Grooved Pins, Full Length Taper-grooved Withdrawn DIN
EN 8744 ISO 8744
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1472 Grooved Pins, Half Length Taper-grooved Withdrawn DIN
EN 8745 ISO 8745
DIN 1473 Grooved Pins, Full Length Parallel-grooved with Chamfer
Withdrawn DIN EN ISO 8740 ISO 8740
DIN 1474 Grooved Pins, Half Length Reverse-grooved Withdrawn DIN
EN 8741 ISO 8741
DIN 1475 Grooved Pins, Third Length Centre-grooved Withdrawn DIN
EN 8742 ISO 8742
DIN 1476 Round Head Grooved Pins Withdrawn DIN EN 8746 ISO
8746
DIN 1477 Countersunk Head Grooved Pins Withdrawn DIN EN 8747 ISO
8747
DIN 1481 Spring-Type Straight Pins (Roll Pins) - Heavy Type
Withdrawn DIN EN ISO 8752 ISO 8752
DIN 1505-1
Bibliographic references to documents - Part 1: Full References
to Printed and Published Documents
Active
DIN 1505-2 Bibliographic references to documents - Part 2: Rules
for Citing
Active
DIN 1505-3
Bibliographic references to documents - Part 3: Indexes of cited
documents (bibliographies)
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1511 Pattern Equipment for Foundries; Production and
Quality
Withdrawn DIN EN 12890 EN 12890
DIN 1530-1 Tools for moulding - Part 1: Ejector pins with
cylindrical head
Active
DIN 1530-2 Tools for moulding - Part 2: Shouldered ejector pins
Active
DIN 1530-3 Tools for moulding - Part 3: Ejector pins with
conical head Active
DIN 1587 Hexagon domed cap nuts Active
DIN 1707 Soft Solders; Composition, Technical Delivery Condition
Active DIN EN ISO 9453 ISO 9453
DIN 1712 Part 1
Aluminium and aluminium alloys - Unalloyed aluminium ingots for
remelting Specifications
Withdrawn DIN EN 576 EN 576
DIN 1712 Part 3
Aluminium; Half-Finished Products Withdrawn DIN EN 573-3 EN
573-3
DIN 1783 Strips, Plates and Sheets of Aluminium and Wrought
Withdrawn DIN EN 485-4 EN 485-4
DIN 1786 Seamless Drawn Copper Tubes for Piping Systems
Withdrawn DIN EN 1057 EN 1057
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1798 Round Rod of Aluminium (Highest Grade Aluminium)
Withdrawn DIN EN 754-3 EN 754-3
DIN 1804 Slotted Round Nut for Hook Spanner; ISO Metric Fine
Thread
Active
DIN 1810 Hook wrenches Active
DIN 1816 Round Nut with Set Pin Holes Inside; ISO Metric Fine
Thread Active
DIN 1912-1 Graphical Representation of Welded, Soldered and
Brazed Joints
Withdrawn DIN EN ISO 17659 ISO 17659
DIN 1912-2 Graphical Representation of Welded, Soldered and
Brazed Joints
Withdrawn DIN EN ISO 6947 ISO 6947
DIN 1912-4
Graphical Representation of Welded, Soldered and Brazed Joints;
Concepts and Terms for Soldered and Brazed Joints and Seams
Active
DIN 1912-5 Symbolic Representation on Drawings of Welded,
Soldered and Brazed Joints
Withdrawn DIN EN 22553 ISO 2553
DIN 1960
Construction contract procedures (VOB) - Part A: General
provisions relating to the award of construction contracts
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1961
Construction contract procedures (VOB) - Part B: General
conditions of contract relating to the execution of construction
work
Active
DIN 2000 to DIN 2999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 2112
Alphanumeric office machines - Alphanumeric keyboards, keyboard
arrangement for manually operated typewriters
Withdrawn DIN 2137-1, DIN 2137-2
DIN 2127
Alphanumeric office machines; alphanumeric keyboards, keyboard
arrangement for electro-mechanical operated typewriters
Withdrawn DIN 2137-1, DIN 2137-2
DIN 2137-1 Keyboards for data and text input - Part 1: German
keyboard layout Active
DIN 2137-2 Keyboards for data and text input - Part 2:
Additional requirements Active
DIN 2342-1 Vocabulary of terminology; basic concepts Active
DIN 2391-1 Seamless precision steel tubes - Part 1: Dimensions
Canceled DIN EN 10305-1 EN 10305-1
DIN 2391-2 Seamless precision steel tubes - Part 2: Canceled DIN
EN 10305-1 EN 10305-1
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
Technical delivery conditions
DIN 2448 Seamless Steel Pipes and Tubes - Dimensions,
Conventional Masses per Unit Length
Canceled DIN EN 10220 EN 10220
DIN 2527 Blank flanges - Nominal pressure 6 to 100 Withdrawn DIN
EN 1092-1 EN 1092-1
DIN 2860 Capillary Fittings; Bends 180 of Copper Withdrawn
DIN 2999-1 Pipe threads for tubes and fittings; parallel
internal thread and taper external thread; tread dimensions
Withdrawn DIN EN 10226-1 EN 10226-1
DIN 2999-2
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical
Internal Thread and Conical External Thread, Gauging System and Use
of Gauges
Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-3 Whitworth Pipe Threads for Tubes and Fittings; Gauge
Dimensions Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-4 Pipe threads for tubes and fittings; sizes for taper
screw limit plug gauges for parallel internal thread
Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-5
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw
Limit Ring Gauges for Gauging Conical External Threads, Sizes
Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-6 Whitworth Pipe Threads for Tubes and Fittings;
Conical Screw Check Plugs, Sizes
Withdrawn DIN EN 10226-3 EN 10226-3
-
DIN 4000 to DIN 4999
DIN TITLE STATUS
DIN REPLACE
MENT
OTHER ORG
REPLACEMENT
DIN 4048-1 Water engineering, terms - Part 1: Dam plants
Active
DIN 4048-2 Water engineering, terms - Part 2: Waterpower plants
Active
DIN 4054 Correction of waterways, terms Active
DIN 4094-1 Subsoil, Field investigations - Part 1: Cone
penetration tests Active
DIN 4102-1 Fire behaviour of building materials and elements -
Part 1: Classification of building materials - Requirements and
testing
Active
DIN 4102-2 Fire Behaviour of Building Materials and Building
Components - Part 2: Building Components; Definitions, Requirements
and Tests
Active
DIN 4102-3 Fire Behaviour of Building Materials and Building
Components - Part 3: Fire Walls and Non-load-bearing External
Walls; Definitions, Requirements and Tests
Active
DIN 4102-4 Fire behaviour of building materials and elements -
Part 4: Overview and design of classified building materials,
elements and components
Active
DIN 4102-5
Fire Behaviour of Building Materials and Building Components -
Part 5: Fire Barriers, Barriers in Lift Wells and Glazings
Resistant against Fire; Definitions, Requirements and Tests
Active
DIN 4102-6 Fire Behaviour of Building Materials and Building
Components - Part 6: Ventilation Ducts; Definitions,
Active
-
DIN TITLE STATUS
DIN REPLACE
MENT
OTHER ORG
REPLACEMENT
Requirements and Tests
DIN 4102-7 Fire behaviour of building materials and elements -
Part 7: Roofing - Concepts, requirements and testing Active
DIN 4102-8 Fire behaviour of building materials and components -
Part 8: Small scale test furnace Active
DIN 4102-9 Fire behaviour of building materials and elements -
Part 9: seals for cable penetrations; concepts, requirements and
testing
Active
DIN 4102-11
Fire behaviour of building materials and building components -
Part 10: pipe encasements, pipe bushings, service shafts and ducts,
and barriers across inspection openings; terminology, requirements
and testing
Active
DIN 4102-12 Fire behaviour of building materials and elements -
Part 12: Fire resistance of electric cable systems required to
maintain circuit integrity - Requirements and testing
Active
DIN 4102-13 Fire behaviour of building materials and elements -
Part 13: Fire resistant glazing; concepts, requirements and
testing
Active
DIN 4102-14 Fire behaviour of building materials and elements -
Part 14: Determination of the burning behaviour of floor covering
systems using a radiant heat source
Active
DIN 4102-15 Fire behaviour of building materials and elements -
Part 15: "Brandschacht" Active
DIN 4102-16 Fire behaviour of building materials and elements -
Part 16: "Brandschacht" tests Active
-
DIN TITLE STATUS
DIN REPLACE
MENT
OTHER ORG
REPLACEMENT
DIN 4102-17 Fire behaviour of building materials and elements -
Part 17: determination of melting point of mineral fibre insulating
materials; concepts, requirements and testing
Active
DIN 4102-18 Fire behaviour of building materials and components
- Part 18: fire barriers, verification of automatic closure
(continuous performance test)
Active
DIN 4102-22 Fire behaviour of building materials and building
components - Part 22: Application standard for DIN 4102-4 based on
the design of partial safety factors
Active
DIN 4108-1 Thermal protection and energy economy in buildings -
Part 1: Quantities and units Active
DIN 4108-2 Thermal protection and energy economy in buildings -
Part 2: Minimum requirements to thermal insulation Active
DIN 4108-3
Thermal protection and energy economy in buildings - Part 3:
Protection against moisture subject to climate conditions;
Requirements and directions for design and construction
Active
DIN 4108-7
Thermal insulation and energy economy of buildings - Part 7:
Airtightness of building, requirements, recommendations and
examples for planning and performance
Active
DIN 4108-10 Thermal insulation and energy economy in buildings -
Part 10: Application-related requirements for thermal insulation
materials - Factory made products
Active
DIN 4150-1 Structural vibration - Part 1: Prediction of
vibration parameters Active
-
DIN TITLE STATUS
DIN REPLACE
MENT
OTHER ORG
REPLACEMENT
DIN 4150-2 Structural vibration - Part 2: Human exposure to
vibration in buildings Active
DIN 4150-3 Structural vibration - Part 3: Effects of vibration
on structures Active
DIN 4420-1 Service and working scaffolds - Part 1: Service
scaffolds - Performance requirements, general design, structural
design
Active
DIN 4512 Photographic sensitometry, determination of optical
density: "Photographische Sensitometrie, Bestimmung der optischen
Dichte" (1934-01, 1957-11, 1961-10)
Withdrawn
DIN 4512-1:1971-04, DIN 4512-3:1973-01, DIN 4512-4:1977-06, DIN
4512-5:1977-10, DIN 4512-6:1980-07
DIN 4512-1 Photographic sensitometry, determination of the speed
of black and white negative materials for pictorial photography
(1971-04, 1993-05)
Withdrawn (2000-09)
DIN ISO 6:1996-02 ISO 6
DIN 4512-3 Photographic sensitometry, determination of diffuse
transmission density (1973-01) Withdrawn
DIN 4512-7:1993-01, DIN 4512-8:1993-01, DIN 4512-9:1993-01
DIN 4512-4 Photographic sensitometry; determination of the speed
of colour reversal films (1977-06, 1985-08)
Withdrawn (2002-06)
DIN ISO 2240:1998-06 ISO 2240
DIN 4512-5 Photographic sensitometry; determination of the speed
of Withdrawn DIN ISO ISO 5800
-
DIN TITLE STATUS
DIN REPLACE
MENT
OTHER ORG
REPLACEMENT
colour negative films (1977-10, 1990-11) (2002-06)
5800:1998-06
DIN 4512-6 Photographic sensitometry; sensitometric illuminants
and light sources (1980-07) Withdrawn
DIN 4512-7 Photographic sensitometry, determination of optical
density; concepts, symbols and notations (1993-01) Active
DIN 4512-8 Photographic sensitometry, determination of optical
density; geometric conditions for transmission density
(1993-01)
Active
DIN 4512-9 Photographic sensitometry, determination of optical
density; spectral conditions (1993-01) Active
DIN 4512-10 Photographic sensitometry, determination of optical
density; geometric conditions for reflection density (1993-01)
Active
DIN V 4701-10
Energy efficiency of heating and ventilation systems in
buildings - Part 10: Heating, domestic hot water supply,
ventilation
Active
DIN V 4701-12
Energetic evaluation of heating and ventilation systems in
existing buildings - Part 12: Heat generation and domestic hot
water generation
Active
DIN 4710 Statistics on German meteorological data for
calculating the energyrequirements for heating and air conditioning
equipment
Active
-
DIN 5000 to DIN 5999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 5008 Rules for text presentation Active
DIN 5031-1
Physics of radiation in the field of optics and illuminating
engineering - Part 1: Quantities, symbols and units of radiation
physics
Active
DIN 5031-2
Physics of radiation in the field of optics and illuminating
engineering - Part 2: Evaluation of radiation by different
detectors
Active
DIN 5031-3
Physics of radiation in the field of optics and illuminating
engineering - Part 3: Quantities, symbols and units of illuminating
engineering
Active
DIN 5031-4 Physics of radiation in the field of optics and
illuminating engineering - Part 4: Efficiencies
Active
DIN 5031-5 Physics of radiation in the field of optics and
illuminating engineering - Part 5: Definitions for temperatures
Active
DIN 5031-6
Physics of radiation in the field of optics and illuminating
engineering - Part 6: Pupil intensity as a measure of retinal
illumination
Active
DIN 5031-7 Physics of radiation in the field of optics and
illuminating engineering - Part 7: Terms for wavebands
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 5031-8
Physics of radiation in the field of optics and illuminating
engineering - Part 8: Definitions and constants of radiation
physics
Active
DIN 5031-9
Physics of radiation in the field of optics and illuminating
engineering - Part 9: Definitions in the field of luminescence
Active
DIN 5031-10
Physics of radiation in the field of optics and illuminating
engineering - Part 10: Photobiologically effective radiation,
quantities, symbols and actions
Active
DIN 5035-3 Artificial lighting - Part 3: Lighting of health care
premises Active
DIN 5035-6 Artificial lighting - Part 6: Measurement and
evaluation Active
DIN 5035-7 Artificial lighting - Part 7: Lighting of interiors
with visual displays work stations
Active
DIN 5035-8 Artificial lighting - Part 8: Workplace luminaries -
Requirements, recommendations and proofing
Active
DIN 5145 Plane irons for wood smooth and for planes Active
DIN 5146 Curved irons for jack planes Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 5406 Lockwashers and locking plates for use with rolling
bearings Active
DIN 5466-1 Splined joints, calculation of load capacity - Part
1: general basis Active
DIN 5473 Logic and set theory; symbols and concepts Active
DIN 5474 Signs in mathematical logic Withdrawn DIN 5473
DIN 5475-1 Complex quantities; nomenclature Withdrawn DIN
5483-3
DIN 5483-1 Time-dependent quantities - Part 1: Terms for the
time-dependency Active
DIN 5483-2 Time-dependent quantities - Part 2: Letter symbols
Active
DIN 5483-3 Time-dependent quantities - Part 3: Complex
representation of sinusoidal time-dependent quantities
Active
DIN 5486 Notation of matrices Withdrawn DIN 1303
DIN 5487 Fourier-, Laplace- and Z-transformation; symbols and
concepts Active
DIN 5489
Directions and signs in electrical engineering; rules for
electric and magnetic circuits, equivalent circuit diagrams
Withdrawn DIN EN 60375 EN 60375
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 5493-2 Logarithmic quantities and units - Part 2:
Logarithmic ratios, levels in nepers and decibels
Active
DIN 6000 to DIN 6999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 6319 Spherical washers and conical seats Active
DIN 6325 Parallel Pins, Hardened; Tolerance Zone m6 Withdrawn
DIN EN ISO 8734 ISO 8734
DIN 6340 Washers for clamping devices Active
DIN 6738 Paper and paper board - Lifespan classes Active
DIN 6776 Technical drawings, labeling Withdrawn DIN EN ISO 3098
ISO 3098
DIN 6797 Toothed lock washers Withdrawn
DIN 6798 Serrated lock washers Withdrawn
DIN 6799 Lock washers (retaining washers) for shafts Active
DIN 6880 Bright Key Steel; Dimensions, Permissible Variations,
Weights Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 6885-1 Drive Type Fastenings without Taper Action Part 1:
Parallel Keys, Keyways, Deep Pattern
Active
DIN 6885-2
Drive Type Fastenings without Taper Action Part 2: Parallel
Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and
Application
Active
DIN 6885-3
Drive Type Fastenings without Taper Action Part 3: Parallel
Keys, Shallow Pattern, Dimensions and Application
Active
DIN 6900 Screw and Washer Assemblies Withdrawn DIN EN 10644 EN
10644
DIN 6901 Tapping screw and washer assemblies Withdrawn DIN EN
10510 EN 10510
DIN 6902 Plain washers for screw and washer assemblies Withdrawn
DIN EN 10673 EN 10673
DIN 6903 Plain washers for tapping screw and washer assemblies
Withdrawn DIN EN 10669 EN 10669
DIN 6912 Hexagon socket thin head cap screws with pilot recess
Active
DIN 6914 High-strength hexagon head bolts with large widths
across flats for structural steel bolting
Withdrawn DIN EN 14399-4 EN 14399-4
DIN 6916 Round washers for high-strength structural steel
bolting Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 6921 Hexagon flange bolts Withdrawn DIN EN 1665 EN 1665
DIN 6922 Hexagon flange bolts with reduced shank Withdrawn DIN
EN 1665 EN 1665
DIN 6923 Hexagon nuts with flange Withdrawn DIN EN 1661 EN
1661
DIN 6924 Prevailing torque type hexagon nuts with nonmetallic
insert Withdrawn DIN EN ISO 7040, DIN EN ISO 10512
ISO 7040, ISO 10512
DIN 6925 Prevailing torque type all-metal hexagon nuts Withdrawn
DIN EN ISO 7042, DIN EN ISO 10513
ISO 7042, ISO 10513
DIN 6926 Prevailing torque type hexagon nuts with flange and
with non-metallic insert
Withdrawn DIN EN 1663, DIN EN 1666 ISO 7043 (modified), ISO
12125(modified)
DIN 6927 Prevailing torque type all-metal nuts with flange
Withdrawn DIN EN 1664, DIN EN 1667
ISO 7044 (modified), ISO 12126 (modified)
DIN 7000 to DIN 7999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 7045
Pan head screws with type H or type Z cross recess - product
grade A
Active
DIN 7245 Saw blades for web saws Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 7337 Break mandrel blind rivets Withdrawn
DIN EN ISO 14589, DIN EN ISO 15977, DIN EN ISO 15978, DIN EN ISO
15979, DIN EN ISO 15980, DIN EN ISO 15981, DIN EN ISO 15982,DIN EN
ISO 15983, DIN EN ISO 15984, DIN EN ISO 16582, DIN EN ISO 16583,
DIN EN ISO 16584
ISO 14589, ISO 15977, ISO 15978,ISO 15979, ISO 15980, ISO
15981,ISO 15982, ISO 15983, ISO 15984,ISO 16582, ISO 16583, ISO
16584
DIN 7343 Spiral Pins; Normal Type Withdrawn DIN EN ISO 8750 ISO
8750
DIN 7344 Spiral Pins; Heavy Duty Type
Withdrawn DIN EN ISO 8748 ISO 8748
DIN 7346
Spring-Type Straight Pins; (Roll Pins) Light-weight Type
Withdrawn DIN EN ISO 13337 ISO 13337
DIN 7349
Plain Washers for Bolts with Heavy Clamping Sleeves
Active
DIN 7500-1
Thread rolling screws for metric ISO thread - Part 1: Types,
designation, requirements
Withdrawn
ISO 7085
DIN 7500-2 Thread rolling screws for ISO metric thread;
guideline values
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
for hole diameters
DIN 7504
Self-drilling screws with tapping screw thread - Dimensions,
requirements and testing
Withdrawn DIN EN ISO 10666,DIN EN ISO 15480, DIN EN ISO
15481,DIN EN ISO 15482, DIN EN ISO 15483
ISO 10666, ISO 15480, ISO 15481,ISO 15482, ISO 15483
DIN 7513
Hexagon head and slotted head thread cutting screws -
Dimensions, requirements and testing
Active
DIN 7516
Cross recessed head thread cutting screws - Dimensions,
requirements and testing
Active
DIN 7603 Ring seals and gaskets Active
DIN 7875
Diving accessories for skin divers; terminology
Withdrawn
DIN 7876
Diving accessories for skin divers; flippers. dimensions.
Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
requirements and testing)
DIN 7877
Diving accessories for skin divers; diver"s masks. requirements
and testing
Withdrawn
DIN 7962
Cross recesses for screws; (modified version of ISO 4757)
Withdrawn DIN EN ISO 4757 ISO 4757
DIN 7970
Threads and thread ends for tapping screws (modified version of
ISO 1478)
Withdrawn DIN EN ISO 1478 ISO 1478
DIN 7971 Slotted pan head tapping screws Withdrawn DIN ISO 1481
ISO 1481
DIN 7972
Slotted countersunk head tapping screws
Withdrawn DIN ISO 1482 ISO 1482
DIN 7973
Slotted raised countersunk head tapping screws
Withdrawn DIN ISO 1483 ISO 1483
DIN 7977 Taper Pins with Thread Ends and Constant
Withdrawn DIN EN 28737 ISO 8737
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
Point Lengths
DIN 7978 Taper Pins with Internal Thread Withdrawn DIN EN 28737
ISO 8736
DIN 7979 Parallel Pins with Internal Thread
Withdrawn DIN EN ISO 8733, DIN EN ISO 8735 ISO 8733, ISO
8735
DIN 7980
Spring lock washers with square ends for cheese head screws
Withdrawn
DIN 7981 Cross recessed pan head tapping screws
Withdrawn DIN ISO 7049 ISO 7049
DIN 7982
Cross recessed countersunk head tapping screws
Withdrawn DIN ISO 7050 ISO 7050
DIN 7983
Countersunk (Flat) Head Tapping Screws with Cross Recess
Withdrawn DIN ISO 7051 ISO 7051
DIN 7984 Hexagon socket thin head cap screws
Active
DIN 7985 Cross recessed raised cheese head screws
Withdrawn DIN EN ISO 7045 ISO 7045
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 7991 Hexagon socket countersunk head cap screws
Withdrawn DIN EN ISO 10642 ISO 10642
DIN 8000 to DIN 8999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 8074 Polyethylene (PE) pipes Dimensions Active
DIN 8075 Polyethylene (PE) pipes - PE 63, PE 80, PE 100, PE-HD -
General quality requirements, testing
Active
DIN 8513-1
Brazing and Braze Weld Filler Metals; Copper Base Brazing
Alloys; Composition, Use, Technical Conditions of Delivery
Withdrawn DIN EN 1044 EN 1044
DIN 8513-2
Brazing and Braze Weld Filler Metals; Silver-bearing Brazing
Alloys with less than 20% by wt. Silver; Composition, Use,
Technical Conditions of Delivery
Withdrawn DIN EN 1044 EN 1044
DIN 8513-3
Brazing filler metals; silver brazing filler metals containing
not less than 20 % of silver; composition, application, technical
delivery conditions
Withdrawn DIN EN 1044 EN 1044
DIN 8513-4
Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing
Alloys; Composition, Use, Technical Conditions of Delivery
Withdrawn DIN EN 1044 EN 1044
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 8513-5
Brazing filler metals; Nickel base filler metals for high
temperature brazing; Application, composition, technical delivery
conditions
Withdrawn DIN EN 1044 EN 1044
DIN 8580 Manufacturing processes - Terms and definitions,
division Active
DIN 8806-1 Narrow band saw blades for woodworking; dimensions
Active
DIN 9000 to DIN 9999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 9021 Plain washers with large outside diameter Withdrawn DIN
EN ISO 7093-1, DIN EN ISO 7093-2
ISO 7093-1, ISO 7093-2
DIN 10000 to DIN 10999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 10504 Food hygiene - Lamps for the lighting of meat and meat
products Withdrawn
-
DIN 11000 to DIN 11999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 11850 Tubes for the food, chemical and pharmaceutical
industry - Stainless steel tubes - Dimensions, materials
Active
DIN 12000 to DIN 12999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 12950-1 Laboratory furniture; safety cabinets for
microbiological and biotechnological work; safety requirements,
tests
Withdrawn
DIN 12950-2
Laboratory furniture; safety cabinets for microbiological and
biotechnological work; containment of class 1 and class 2 cabinets,
microbiological test
Withdrawn
DIN 12950-10
Laboratory furniture; safety cabinets for microbiological and
biotechnological and biotechnological work; requirements and
testing
Withdrawn
DIN 12975-1 Thermal solar systems and components - Solar
collectors - Part 1: General requirements
DIN 12975-2 Thermal solar systems and components - Solar
collectors - Part 2: Test methods
DIN 12976-1 Thermal solar systems and components - Factory made
systems - Part 1: General requirements
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 12976-2 Thermal solar systems and components - Factory made
systems - Part 2: Test methods
DIN 13000 to DIN 13999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 13080 Division of hospitals into functional areas and
functional sections Active
DIN 13260-2
Supply systems for medical gases - Part 2: Dimensions and
allocation of probes and gas-specific connection points for
terminal units for compressed medical gases and vacuum
Active
DIN 13432
Packaging - Requirements for packaging recoverable through
composting and biodegradation - Test scheme and evaluation criteria
for the final acceptance of packaging
Active DIN EN 13432
DIN 13715 Workpiece cornes and edges Active DIN ISO
13715(200012)
DIN 14000 to DIN 14999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 14090 Areas for the fire brigade on premises Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 14096-1 Fire precaution regulation - Part 1: General and
part A (placard); rules for drafting and placarding
Active
DIN 14096-2
Fire precaution regulation - Part 2: Part B (for persons without
special tasks of fire prevention and fire fighting); rules for
drafting
Active
DIN 14096-3
Fire precaution regulation - Part 3: Part C (for persons with
special tasks of fire prevention and fire fighting); rules for
drafting
Active
DIN 14210 Water pool for firefighting Active
DIN 14406-4 Portable fire extinguishers - Part 4: Maintenance
Active
DIN 14503 Trailers for firefighting purposes, two-wheeled;
general requirements Withdrawn DIN 14521
DIN 14505 Firefighting and rescue service vehicles - Vehicles
for roller containers - General requirements
Active
DIN 14507 Rescue service vehicles - Vehicles for roller
containers - General requirements
Active
DIN 14520 Trailers for portable fire pumps Withdrawn
DIN 14521 Firefighting - Trailer with removable foam-water
monitor Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 14530-5
Fire fighting vehicles - Part 5: Group pumping appliance LF
10/6, Group pumping appliance for rescue operations HLF 10/6
Active
DIN 14530-11
Fire fighting vehicles - Part 11: Group pumping appliance LF
20/16, Group pumping appliance for rescue operations HLF 20/16
Active
DIN 14530-16 Fire fighting vehicles - Part 16: Pumping appliance
TSF Active
DIN 14530-17 Fire fighting vehicles - Part 17: Pumping appliance
TSF-W Active
DIN 14530-21 Fire fighting vehicles - Part 21: Pump water tanker
TLF 20/40, Pump water tanker TLF 20/40-SL
Active
DIN 14530-22 Fire fighting vehicles - Part 22: TLF 16/24-TR
Active
DIN 14530-24 Fire fighting vehicles - Part 24: Small pumping
appliance KLF Active
DIN 14530-25 Fire fighting vehicles - Part 25: Pumping appliance
STLF 10/6 Active
DIN 14555-1 Vehicles carrying tools and gears - Part 1: General
requirements Active
DIN 14555-3 Vehicles carrying tools and gears - Part 3:
Emergency tender RW Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 14555-12 Vehicles carrying tools and gears - Part 12: Damage
control tender GW-G Active
DIN 14555-21 Vehicles carrying tools and gears - Part 21: GW-L1
for logistic tasks Active
DIN 14555-22 Vehicles carrying tools and gears - Part 22: GW-L2
for logistic tasks Active
DIN 14565 Fire hose tender; Type SW 2000-TR Withdrawn
DIN 14701-1 Turntable ladders and similar fire fighting
vehicles; Purpose, concepts, safety equipment, requirements
Withdrawn DIN EN 1777 EN 1777
DIN 14701-2 Turntable ladders and similar fire fighting
vehicles; Turn table ladders, engine driven
Withdrawn DIN EN 14043, DIN EN 14044 EN 14043, EN 14044
DIN 14701-3 Turntable ladders and similar fire fighting
vehicles; Rescue baskets Withdrawn DIN EN 1777 EN 1777
DIN 14702 Turntable ladder DL 16-4, hand operating Active
DIN 14703 Trailer Ladder AL 16-4 Active
DIN 14710-1 Hook ladder, manufactured using wood; with hinged
hook Withdrawn DIN EN 1147 EN 1147
DIN 14710-3 Hook light metal ladder Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 14711-1 Scaling ladder; made from wood Withdrawn DIN EN 1147
EN 1147
DIN 14711-2 Scaling ladder; made from light metal Withdrawn DIN
EN 1147 EN 1147
DIN 14711-3 Scaling ladder; socket rungs and socket parts
Withdrawn DIN EN 1147 EN 1147
DIN 14713 Folding ladder Withdrawn DIN EN 1147 EN 1147
DIN 14715-1 Three piece extension ladder made from wood
Withdrawn DIN EN 1147 EN 1147
DIN 14715-2 Three piece extension ladder; made of light metal
Withdrawn DIN EN 1147 EN 1147
DIN 15000 to DIN 15999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 15018-2 Cranes; steel structures; principles of design and
construction Active
DIN 15185-1
Warehouse systems with guided industrial trucks; requirements on
the ground, the warehouse and other requirements
Active
DIN 15185-2
Warehousesystems with powered industrials trucks; code of
practice for the protection of persons when operating with trucks
in narrow aisles; safety requirements, testing
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 15721 Film 70 mm; projection reel Active
DIN 16000 to DIN 16999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 16518 Classification of types Active
DIN 16892
Cross-linked high-density polyethylene (PE-X) pipes - General
qualityrequirements and testing
Active
DIN 16893 Cross-linked high-density polyethylene (PE-X) pipes
Dimensions
Active
DIN 17000 to DIN 17999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 17175 Seamless Tubes of heat Resistant Steels Withdraw DIN
EN 10216-2
DIN 17410 Materials for permanent magnets: Technical conditions
Active
DIN 17457
Withdraw DIN EN 10217-7
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 17458
Withdraw DIN EN 10216-5
DIN 17471 Resistance alloys Active
DIN 18000 to DIN 18999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 18012 House service connections facilities - Principles for
planning Active
DIN 18013 Recesses for meter boards (electric meters) Active
DIN 18014 Foundation earth electrode - General planning criteria
Active
DIN 18015-1 Electrical installations in residential buildings -
Part 1: Planning principles Active
DIN 18015-2 Electrical installations in residential buildings -
Part 2: Nature and extent of minimum equipment
Active
DIN 18015-3 Electrical installations in residential buildings -
Part 3: Wiring and disposition of electrical equipment
Active
DIN 18022 Domestic kitchens, bathrooms and WCs; design
principles Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 18024-1
Barrier-free built environment - Part 1: Streets, squares,
paths, public transport, recreation areas and playgrounds - Design
principles
Active
DIN 18024-2 Construction of accessible buildings - Part 2:
Publicly accessible buildings and workplaces, design principles
Active
DIN 18065 Stairs in buildings - Terminology, measuring rules,
main dimensions Active
DIN 18379
Construction contract procedures (VOB) - Part C: General
technical specifications in construction contracts (ATV) -
Installation of air conditioning systems
Active
DIN 18382
Contract procedures for building works - Part C: General
technical specifications for building works; Low-voltage
installation and medium-voltage installation with nominal voltages
up to including 36 kV
Active
DIN 18384
Construction contract procedures (VOB) - Part C: General
technical specifications in construction contracts (ATV);
Installation of lightningprotection systems
Active
DIN 18800-1 Steel structures - Part 1: Design and construction
Withdrawn DIN EN 1993 DIN EN 1090
DIN 18800-2 Steel structures - Part 2: Analysis of safety
against buckling of linear members and frames
Withdrawn DIN EN 1993
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 18800-3 Steel structures - Part 3: Analysis of safety
against buckling of plates Withdrawn DIN EN 1993
DIN 18800-4 Steel structures - Part 4: Analysis of safety
against buckling of shells Withdrawn DIN EN 1993
DIN 18800-5 Steel structures - Part 5: Composite structures of
steel and concrete - Design and construction
Withdrawn DIN EN 1994
DIN 18800-7 Steel structures - Part 7: Execution and
constructor's qualification Active
EN 1090-2
DIN 19000 to DIN 19999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN V 19222 Control technology Terminology Active
DIN 19225 Measurement and control; terminology and
classification of controllers Active
DIN 19226-1 Control technology - Part 1: General terms and
definitions Active
DIN 19226-2 Control technology - Part 2: Terms and definitions;
dynamic systems behaviour
Active
DIN 19226-3 Control technology - Part 3: Terms and definitions
of switching systems behaviour
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 19226-4 Control technology - Part 4: Terms and definitions
of control systems Active
DIN 19226-5 Control technology - Part 5: Functional terms
Active
DIN 19226-6 Control technology - Part 6: Terms and definitions
of functional and constructional units
Active
DIN 19227-1
Control technology; graphical symbols and identifying letters
for process control engineering; symbolic representation for
functions
Active
DIN 19227-2
Control technology; graphical symbols and identifying letters
for process control engineering; representation of details
Active
DIN 19237 Measurement and control; control engineering
vocabulary Withdrawn
DIN 19226-3, DIN 19226-4, DIN 19226-5, DIN 19226-6
DIN 19227-1
Control technology; graphical symbols and identifying letters
for process control engineering; symbolic representation for
functions
Active
DIN 19227-2
Control technology; graphical symbols and identifying letters
for process control engineering; representation of details
Active
DIN 19533 Pipe-lines of high-density PE (high-density
polyethylene) and low-density
Withdrawn DIN EN 12201-1, DIN EN 12201-2,
EN 12201-1, EN 12201-2,
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
PE (low density polyethylene) for drinking water supply; pipes,
pipe connections and fittings for pipe-lines
DIN EN 12201-3, DIN EN 12201-5
EN 12201-3, EN 12201-5
DIN 19704-1 Hydraulic steel structures - Part 1: Criteria for
design and calculation Active
DIN 19704-2 Hydraulic steel structures - Part 2: Design and
manufacturing Active
DIN 19704-3 Hydraulic steel structures - Part 3: Electrical
equipment Active
DIN 24000 to DIN 24999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 24190 Ventilation and air conditioning - folded and welded
rectangular sheet metal ducts
Withdrawn
DIN 24340-2 Hydraulic valves; mounting surfaces and connecting
plates for directionalcontrol valves
Active
DIN 28000 to DIN 28999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 28610-1 Ductile iron pressure pipes with socket with
cement-mortar lining for gas and
Withdrawn DIN EN 545, DIN EN 969 EN 545, EN 969
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
water pipelines; dimensions and masses
DIN 28610-2
Ductile iron pressure pipes with socket for gas and water
pipelines rated for pressures over 4 bar up to and including 16
bar; dimensions and masses
Withdrawn DIN EN 969 EN 969
DIN 30000 to DIN 39999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 30722-1
Roller contact tipper vehicles, roller containers - Part 1:
Roller contact tipper vehicles up to 26 t, roller containers type
1570 made from steel
Active
DIN 30722-2
Roller contact tipper vehicles, roller containers - Part 2:
Roller contact tipper vehicles up to 32 t, roller containers type
1570 made from steel
Active
DIN 30722-3
Roller contact tipper vehicles, roller containers - Part 3:
Roller contact tipper vehicles up to 12 t, roller containers type
900 made from steel
Active
DIN 30722-4 Roller containers for the transport on road and rail
Active
-
DIN 31000 to DIN 31999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT
DIN 31635 Conversion of the Arabic alphabet Active
DIN 40000 to DIN 49999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 40015 Frequency and wave bands Active
DIN 40020 Guidelines for the user interface in multimedia
equipment for general purpose use (IEC/TR 61997:2001)
Active
DIN 40050-9 Road vehicles; degrees of protection (IP-code);
protection against foreign objects; water and contact; electrical
equipment
Active
DIN 40101-1 Graphical symbols for use on equipment Withdrawn
DIN 40101-2 Graphical symbols for use on equipment; graphical
symbols from ISO 7000 for electrical engineering
Active
DIN 40108 Electric power technology - Current systems -
Concepts, quantities, letter symbols
Active
DIN 40110-1 Quantities used in alternating current theory - Part
2: Two-line circuits Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 40110-2 Quantities used in alternating current theory - Part
2: Multi-line circuits Active
DIN 40146-1 Telecommunications - Part 1: Basic concepts
Active
DIN 40148-1 Transmission systems and two-ports; concepts and
quantities Active
DIN 40148-2 Transmission systems and two-ports; symmetry
characteristics of linear two-ports
Active
DIN 40148-3 Transmission systems and two-ports; measures for
attenuation Active
DIN 40200 Nominal value, limiting value, rated value, rating -
concepts Active
DIN 41215 Electrical communication engineering; electromagnetic
relays, definitions Withdrawn
DIN 41301 Electro Sheets; Magnetic Materials for Transformers
Withdrawn
DIN 41309-1 Small transformers and chokes; strip-wound cut
cores; types SM, SE, SU, SG and S3U; dimensions materials
Withdrawn
DIN 41309-2
Small transformers and chokes; strip-wound cut cores; technical
conditions of delivery for one phase applications; types SM, SE, SU
and SG
Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 41309-3
Small transformers and chokes; strip-wound cut cores; technical
conditions of delivery for three phase applications; type S3U
Withdrawn
DIN 41426 Nominal values of resistors and capacitors Withdrawn
DIN IEC 60063 IEC 60063
DIN 41429 Colour code for fixed resistors Withdrawn DIN EN 60062
EN 60062
DIN 41524 Circular connectors for radio and associated sound
equipment three and five-pole connectors
Withdrawn
DIN 41612-1 Two-part connectors for printed board, grid 2,54 mm;
common mounting features; survey of types
Withdrawn DIN 41612-1 S1
DIN 41612-1 S1
Two piece connectors for printed circuits, grid 2,54 mm (0,1
in); general allusions Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-2 Two-part connectors for printed boards; grid 2,54mm;
dimensions of types B, C and D
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-3 Two part connectors for printed boards; grid 2,54mm;
dimensions of types F and G
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-4 Two-part connectors for printed boards; grid 2,54mm,
dimensions of type H Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-5 Two-part connectors for printed boards; grid 2,54mm;
ratings, requirements, tests Withdrawn DIN EN 60603-2 EN
60603-2
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 41612-6 Two-part connection for printed boards; grid 2.54mm;
dimensions of types Q, R and S
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-7 Two-part connectors for printed boards; grid 2,54
mm; dimensions of types U and V
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-8 Two-part connectors for printed boards; grid 2.54
mm; dimensions of type M Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-8 S1
Two-part connectors for printed boards; grid 2.54 mm; dimensions
of type M; survey of special contracts for use with type M
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-9 Two-part connectors for printed boards; grid 2,54
mm; dimensions of type E Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-10
Two-part connectors for printed boards; grid 2,54mm; gauges
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-102
Two-part connectors for printed boards; dimensions for type X
Withdrawn DIN 41612-9
DIN 41612-103
Two-part connectors for printed boards; dimensions of type M
Withdrawn DIN 41612-8
DIN 41652-1 Rack and panel connectors, trapezoidal, round
contacts 1 mm; common mounting features and dimensions; survey of
types
Active
DIN 41652-2 Rack and panel connectors; trapezoidal, round
contacts 1 mm; ratings, requirements, tests
Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 41750-1
Rack and panel connectors, trapezoidal, round contacts 1 mm;
common mounting features and dimensions; survey of types
Active
DIN 41750-2 Rack and panel connectors, trapezoidal, round
contacts 1 mm; ratings, requirements, tests
Active
DIN 41750-3 Rack and panel connectors, trapezoidal, round
contacts 1 mm; dimensions of type A; solder termination for free
wiring
Active
DIN 41750-5 Rack and panel connectors, trapezoidal, round
contacts 1 mm; dimensions of type C; crimp termination for free
wiring
Active
DIN 41782 Guidelines for the presentation of published data
Withdrawn DIN IEC 60747-2 IEC 60747-2
DIN 41786 Thyristors, definitions Withdrawn
DIN 41855 Semiconductor devices and integrated circuits; kinds
of devices and general terms
Withdrawn
DIN 41855-2 Semiconductor devices and integrated circuits;
optoelectronic semiconductor devices; terms and definitions
Withdrawn
DIN 41868 Cases 10 A 3 and 10 B 3 for semiconductor devices;
main dimensions Withdrawn
DIN 41869-1 Case 23 A 3 for semiconductor devices; main
dimensions Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 41869-2 Cases 34 A 2 and 34 A 3 for semiconductor devices;
main dimensions Withdrawn
DIN 41869-3 Case 11 A 3 and 11 B 3 for semiconductor devices;
main dimensions Withdrawn
DIN 41869-4 Case 12 A 3 for semiconductor devices; main
dimensions Withdrawn
DIN 41869-5 Case 13 A 3 for semiconductor devices; main
dimensions Withdrawn
DIN 41869-6 Case 14 A 3 for semiconductor devices; main
dimensions Withdrawn
DIN 41869-7 Case type 15 for semiconductor devices; main
dimensions Withdrawn
DIN 41873 Cases type 5 for semiconductor devices and integrated
circuits Withdrawn
DIN 41876 Cases 18 A, B and C with 2 up to 4 terminals for
semiconductor devices; main dimensions
Withdrawn
DIN 42400 Terminal markings for electrical equipment; general
rules, alphanumeric system
Withdrawn DIN EN 60445 EN 60445
DIN 42402 Terminal markings for power transformers and reactors
Active
DIN 42403 Terminal markings for power converters Withdrawn DIN
IEC 61148 IEC 61148
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 42673-1
Totally enclosed fan-cooled three-phase induction motors
squirrel-cage, type IM B 3, with rolling bearing; mounting
dimensions and relationship frame sizes-output ratings
Withdrawn
DIN 42673-2
Totally enclosed fan-cooled three-phase induction motors with
squirrel-cage, type IM B 3, with rolling bearings; relationship
frame sizes - output ratings for type of protection increased
safety "e"
Active
DIN 42673-3
Totally enclosed fan-cooled three-phase induction motors with
squirrel-cage, type IM B 3, with rolling bearings; relationship
frame sizes - output ratings for type of protection flameproof
enclosure "d"
Active
DIN 42673-4
Totally-enclosed fan-cooled alternating-current polyphase motors
with squirrel-cage, design B3, with ball bearings, maximum envelope
dimensions
Active
DIN 42961 Rating plates for rotating electrical machinery;
design Active
DIN 42973 Rated output values for rotating electrical machinery
for continuous duty Active
DIN 43700
Measurement and control - Measurement and control instruments
for panel mounting - Nominal front- and cut-out-dimensions
Withdrawn DIN IEC 61554 IEC 61554
DIN 43780 Electrical measuring instruments; direct acting
indicating electrical measuring instruments and their
accessories
Withdrawn DIN EN 60051-1 EN 60051-1
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 43802-2 Line scales and pointers for indicating electrical
measuring instruments; general requirements
Active
DIN 43802-3 Line scales and pointers for indicating electrical
measuring instruments; designs and dimensions
Active
DIN 43802-4 Line scales and pointers for indicating electrical
measuring instruments; scale graduation and numbering
Active
DIN 43807
Measuring and control; electrical measuring instruments;
terminal markings for switchboard meters, panel meters and
measuring transducers for the measurement of power and power
factor
Active
DIN 43856
Electricity meters, tariff time switches and ripple control
receivers; connection diagrams, terminal marking, circuit
diagrams
Active
DIN 43856-2 Electricity meters - Part 2: Marking of auxiliary
terminals for tariff devices according to IEC-Report 61354:1995
Active
DIN 43870-1 Meter mounting boards; dimensions based on a grid
system Active
DIN 43870-2 Meter mounting boards; functional area Active
DIN 43870-3 Meter panels; wirings Active
DIN 44070-1 Meter mounting boards; dimensions Active
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
based on a grid system
DIN 44070-2 Meter mounting boards; functional area Active
DIN 44070-3 Meter panels; wirings Active
DIN 44070-4 Meter panels; cover for wiring Active
DIN 44080 Thermistors; PTC, technical terms and tests
Withdrawn
DIN 44300 Information processing; vocabulary Withdrawn
DIN 44300-1 Information processing - Concepts - General terms
Withdrawn
DIN 44300-2 Information processing - Concepts - Representation
of data Withdrawn
DIN 44300-3 Information processing - Concepts - Data structures
Withdrawn
DIN 44300-4 Information processing - Concepts Programming
Withdrawn
DIN 44300-5 Information processing - Concepts - Components of
digital computer systems Withdrawn
DIN 44300-6 Information processing - Concepts Storage
Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 44300-7 Information processing - Concepts Times
Withdrawn
DIN 44300-8 Information processing - Concepts - Processing
functions Withdrawn
DIN 44300-9 Information processing - Concepts - Process
relations and modes of operation Withdrawn
DIN 45322 Circular connectors for radio and associated sound
equipment; six-pole connectors
Withdrawn DIN EN 60130-9 EN 60130-9
DIN 45323
Connectors for coupling an external low-voltage power to
portable entertainment equipment (describes at least two DC coaxial
power plugs)
Active
DIN 45500-1 High fidelity audio equipment and systems; minimum
performance requirements; Part 1: general
Withdrawn DIN EN 61305-1 EN 61305-1
DIN 45500-2 High fidelity audio equipment and systems;
requirements for tuner equipments
Withdrawn DIN EN 61305-2 EN 61305-2
DIN 45500-3 High fidelity audio equipment and systems;
requirements for disk record reproducing equipments
Withdrawn
DIN 45500-4
High fidelity audio equipment and systems; minimum performance
requirements for magnetic recording and reproducing equipment
Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 45500-5 High fidelity audio equipment and systems; minimum
performance requirements for microphones
Withdrawn
DIN 45500-6 High fidelity audio equipment and systems; minimum
performance requirements for amplifiers
Withdrawn DIN EN 61305-3 EN 61305-3
DIN 45500-7 High fidelity audio equipment and systems;
requirements for loudspeakers Withdrawn DIN EN 61305-5 EN
61305-5
DIN 45500-8 High fidelity audio equipment and systems; for sets
and systems Withdrawn
DIN 45500-10
High fidelity audio equipment and systems; minimum performance
requirements for headphones
Withdrawn
DIN 45507 Measuring apparatus for frequency variations in sound
recording equipment Withdrawn DIN IEC 60386 IEC 60386
DIN 45539
Disk record reproducing equipment; directives for measurements,
markings and audio frequency connections, dimensions of
interchangeable pickups, requirements of play back amplifiers
Withdrawn DIN IEC 60098 IEC 60098
DIN 45596 Microphones; phantom powering Withdrawn
DIN 46400-1
Steel flats with special magnetic properties cold rolled, non -
oriented, finally annealed magnetic sheet and strip hysteresis loss
at frequencies above 100 Hz
Withdrawn DIN EN 10106 EN 10106
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 46400-3 Grain-oriented magnetic steel and strip technical
conditions Withdrawn DIN EN 10107 EN 10107
DIN 47100 Cords for telecommunication; code of insulated
conductors, colour of sheath Withdrawn
DIN 47301-1 Terms of HF-lines Active
DIN 47301-2 Terms of HF-lines Active
DIN 47301-3 Definition of radio frequency transmission lines -
mean characteristic impedance - mean standing wave ratio
Active
DIN 48803 Lightning protection system; Arrangement of components
and dimensions for mounting
Withdrawn
DIN 48830 Lightning protection system; Description Withdrawn
DIN 50000 to DIN 59999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 51097
Testing of floor coverings; determination of the anti-slip
properties: wet-loaded barefoot areas; walking method; ramp
test
Withdrawn DIN 51130
DIN 51130 Testing of floor coverings; determination of the
anti-slip properties: workrooms and fields of activities with slip
danger,
Withdrawn DIN 51097
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
walking method - ramp test
DIN 51501 Lubricants; Lubricating Oils L-AN; Minimum
Requirements Withdrawn
DIN 52368 Testing of particleboards; determination of
formaldehyde emission by gas analysis
Withdrawn DIN EN 717-2 EN 717-2
DIN 53150 Paints and varnishes - Determination of the drying
stage of coatings (modified Bandow-Wolff method)
Active
DIN 53438 Testing of combustible materials; response to ignition
by small flame Active
DIN 53452 Testing of Plastics; Flexural Test Withdrawn DIN EN
ISO 178 ISO 178
DIN 53575 Flexible Cellular Polymeric Materials - Determination
of Tear Strength Withdrawn DIN EN ISO 8067 ISO 8067
DIN 54836 Testing of combustible materials; determination of
ignition temperature Active
DIN 54837 Determination of burning behaviour using a gas burner
Active
DIN 55003-3 Machine tools; symbols; numerically controlled
machine tools Withdrawn
DIN 58810 Surgical implants; threads for bone screws and nuts
Withdrawn
-
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 58888 Thread connection for microscope objectives Withdrawn
DIN ISO 8038-1 ISO 8038-1
DIN ISO 53438
DIN 60000 to DIN 69999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 66000 Information processing; switching algebra,
mathematical signs and symbols Active
DIN 66001 Information processing; graphical symbols and their
application Active
DIN 66002 Information processing; handwriting of the digit 0 and
of the upper case letter O Active
DIN 66003 Information technology - 7-bit code Active
DIN 66004-1 Information processing - Coding on data media - Part
1: Representation of 7-bit code character sets on punched tape
25
Active
DIN 66004-2
Information processing - Coding on data media - Part 2:
Representation of 7-bit coded and 8-bit coded character sets on
punched cards
Active
DIN 66004-3
Information processing - Coding on data media - Part 3:
Representation of 7-bit coded and 8-bit c