This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
P R O D U C T O V E R V I E W
LIQUIDCONTROLSA Unit of IDEX Corporation
Turbine Meters & Accessories
• Aerospace
• Agriculture
• Chemical
• Cryogenic
• Food
• Gases
• Military
• Petrochemical
• Petroleum
• Pharmaceutical
• Pulp & Paper
• Utilities
Distributed by Flow-Tech Industries [email protected] www.flow-tech.com
Pickup Coil StandardTemperature from -450°F (-268°C) to +450°F(+232°C) [Optional to +1000°F (+538°C)]Amplifier recommended to minimize EMI
Bearing Choices Include:Standard: Stainless Steel or Cryo Ball
Bearings
Options: FluorosintCarbide Sleeve Bearings
Standard End Fittings Include:Male NPT Standard37° Flare StandardANSI Flange StandardSanitary Optional
(For Others Including HighPressure, See Description Chart)
Materials of Construction Include:Standard–304 Stainless Steel Optional–316/316L Stainless Steel, Monel, Brass, Aluminum, Alloy 20, Plastic
Note: Corrosive series materials available.Consult factory.
Standard with Flow Straightener both upstream and downstream for improved accuracy
Lightweight, HydraulicallyBalanced Rotor. No Thrust Bearing
17-4 PH Stainless SteelRotor Construction(Standart)Note: For other materials,
Consult Factory
Features
Absolute Accountability InTurbine Meter TechnologyLC Turbine Meters offer unsurpassedaccuracy, efficiency and service life, andmeet most liquid or gas flow measure-ment applications. LC Turbine Metersavailable in stainless steel or corrosiveseries with a hydraulically balanced tur-bine rotor
(no thrust bearing) and rugged, compact construction for the mostaccurate and reliable measurementavailable. Flow ranges are from 0.25 to12,000 GPM and temperatures from -450°F (-268°C) to +1,000°F (+538°C). A wide variety of electronic
instrumentation and components complete your flow needs.
Features include: •High pressure applications.•Custom and standard designs.•Wide choice of bearings, including
carbide•Interfaces with manual, semiautomated
or completely automated systems.•Materials compatible with application.•Custom design and system
NitrogenNitrous OxideOxygenSteam (Consult Factory)Water, DIWater, FreshWater, Salt
Typical Application for Liquids & Gases
304 Stainless Steel Support Shaft & Cones (Standard) Does Not Turn
2 Distributed by Flow-Tech Industries [email protected] www.flow-tech.com
7
Model LC711-3 A meter-mounted 3-wire AnalogTransmitter designed to linearly convert a frequencyinput to an equivalent voltage output whose level is switch selectable @0-5V/0-10V.
Model LC712-2 A meter mounted true 2-wire loop powered Analog Transmitterdesigned to linearly convert a frequency input to an equivalent4-20mA current output.Model LC714 A meter-mounted device that amplifies and conditions low-amplitude signals such as those developed by a magnetic pickupcoil. The amplitude of the squarewave output equals the input sup-ply voltage.
• FM approved and CSA certified, Class I, Group B, C & D andClass II, Group E, F & G, Nema 4
• Direct mounted to Flow Meter
Model LC200N - RATE A battery powered industrial Remote Rate Indicator device that provides Flow Rate in any engineering unit. Rate is displayed via an 8-digit Liquid Crystal Display. Selection of the Reset Function isaccomplished externally by magnetic field to maintain unit integritywhile permitting complete operational control in hazardous environments. Auxiliary digital factored pulse output is standard.
Model LC150N-TOTAL A battery powered Industrial Remote Totalizer that provides FlowTotalization in any engineering unit. Total is displayed via an 8-digit Liquid Crystal Display. Reset of the Totalizer is accomplishedexternally by a magnetic field to retain unit integrity while permit-ting complete operational control in hazardous environments.Auxiliary digital factored pulse output is standard.
Model LC275N-RATE/TOTAL A battery powered device providing flow totalization and rate in any engineering unit. Total and Rate are displayed via two 8-digit Liquid Crystal Displays.
The totalizer Reset Function is accomplished externally bya magnetic field to retain unit integrity while permittingcomplete operational control in hazardous environments.In addition, the LC275N provides one analog interface output.The 4-20mA loop control extracts no power from the loop.
•DC powered by internal AA Lithium battery
•FM approved and CSA certified, Class I, Group B, C & D and ClassII, Group E, F & G, Nema 4
•Direct mounted to Flow Meter
•Fully programmable, field calibration via BCD switches
Model LC300N-RATE/TOTAL An industrial counter providing rate and flow totalization in anyengineering unit. Unit features 10-point linearization with 1 pulseand 1 analog output. Can be battery, loop or VDC powered.
Model LC150N - Totalizer Model LC275N -Rate/Totals Indicator
Model LC300N -Rate/Totals Indicator
Explosion Proof Rate And/Or Totalizer Indicators
Explosion Proof Transmitters & Amplifiers
Model LC200N - Rate
Distributed by Flow-Tech Industries [email protected] www.flow-tech.com
Data Based on H2O for Liquids/Air for Gases
MODEL DESCRIPTION CHARTLC 1/4 -MB-NL-A-4-HTX
Gros
s Pre
ssur
e Dr
op–P
SID
• = Min. Linear FlowFor estimating pressure drop on liquids other than water at room temperature:
P = ! Visc* (Cpse) 1/4 x Sp. Gr. 3/4 x ! PH2O(Corrected) (from Curve)
* Absolute Visc (C'poise) = Kinematic Visc (C'stokes) x Sp. Gr.
For estimating pressure drop on gases at densities other than 1Lb/Ft3:
Meter size is based on nominal inside diameter of pipe. For installation dimensions for sizes larger than 6", consult factory.For proper matching always specify inside diameter of mating pipe.Special flanges can usually be provided to specification.For hazardous areas, pick up coils with explosion proof housing can be provided.All Flowmeters 1/2" and smaller will be provided with 1/2" End Connections unless otherwise specified.
End Flanged (ANSI B16.5) SIZES (1/2" - 12")
Installation Dimensions (INCHES)
IMPORTANT: Dimensions shown are NOT for construction use. Consult factorywhen certified Engineering Prints are required.
4
Typical Arrangement of Flowmeter Readouts
Distributed by Flow-Tech Industries [email protected] www.flow-tech.com
LINE DIMENSIONS (inches) END CONNECTIONS APROX. WTSIZE A B C FLARED TUBE LBS/Kg
1/4-1/2 1 1/8 2 5/8 3 3/4-16UNF-3A .38/.173
5/8 1 1/8 2 3/4 3 7/8-14UNF-3A .75/.341
3/4 1 5/8 3 1/4 3 1/2 1 1/16-12UN-3A .75/.341
1 1 5/8 3 1/2 4 1 5/16-12UN-3A 1.3/.627
1 1/4 2 3 7/8 4 3/8 1 5/8-12UN-3A 1.75/.795
1 1/2 2 1/8 4 3/8 4 5/8 1 7/8-12UN-3A 2.31/1.05
2 2 3/4 4 3/4 5 3/8 2 1/2-12UN-3A 3.0/1.36
MS Flared Tube SIZES (1/4" - 2")
IMPORTANT: Dimensions shown are NOT for construction use. Consult factorywhen certified Engineering Prints are required.
5
Typical Flowmeter System Installation
LINE DIMENSIONS (inches) END CONNECTIONS APPROX. WTSIZE A B C MNPT LBS/Kg
1/4-1/2 1 1/8 3 3 1/2 .38/.173
5/8 1 1/8 3 3 1/2 .75/.341
3/4 1 5/8 3 1/4 3 1/2 3/4 .75/.341
1 1 5/8 3 1/2 4 1 1.3/.627
1 1/4 2 3 7/8 4 3/8 1 1/4 1.75/.795
1 1/2 2 1/8 4 3/8 4 5/8 1 1/2 2.31/1.05
2 2 3/4 4 3/4 5 3/8 2 3.0/1.36
2 1/2 3 1/4 6 1/16 5 3/8 2 1/2 5.5/2.50
3 3 1/2 10 5 5/8 3 10/4.54
Male NPT SIZES (1/4" - 3" )
IMPORTANT: Dimensions shown are NOT for construction use. Consult factorywhen certified Engineering Prints are required.
Distributed by Flow-Tech Industries [email protected] www.flow-tech.com
SOLD AND SERVICED BY A NETWORK OF HIGHLY TRAINEDFULL SERVICE DISTRIBUTORS
LIQUID CONTROLSA Unit of IDEX Corporation105 Albrecht DriveLake Bluff, IL 60044-2242(847) 295-1050FAX: (847) 295-1057Website: www.lcmeter.com
LIQUIDCONTROLSA Unit of IDEX Corporation
®
WARRANTY:The seller’s products are warranted against defects inmaterial or workmanship for a period of (1) year fromdate of LC invoice. Seller’s obligations, as set forthbelow, shall apply only to failure(s) to meet the foregoing obligations provided that Seller is given written notice within thirty (30) days of any occurrencefrom which a claim of defect arises. In the event that afactory inspection by Seller’s or it’s designee(s) supportsthe validity of a claim at the discretion of Seller, repair,replacement, or refund shall be the sole remedy fordefect and shall be made, free of charge, Ex-works factory. In no event shall Seller be liable for any special
consequential, incidental, indirect or exemplary damages arising out of warranty, contract tort (including negligence) or otherwise, including but not limited to, loss of profit or revenue, loss of use of the product or any and all associated products and/orequipment, cost of substitute goods or services, down-time costs or claims of or by Purchaser’s clients or customers. In any event, the total liability of Seller for any and all claims arising out of or resulting fromthe performance, non-performance or use of the product shall not exceed the purchase price of the individual product giving rise to the claim. All otherguaranties, warranties, conditions and representations
either express or implied, whether arising under anystatute, common law, commercial usage or otherwiseare excluded. Electronic products require installation,start-up and servicing by local factory-trained servicerepresentatives. In the absence of installation, start-upand servicing of electronic products by Seller trainedservice representatives, this warranty is null and void.Seller’s obligations as set forth above shall not apply toany product, or any component or part thereof, whichis not properly installed, used, maintained or repaired,or which is modified other than pursuant to Seller’sinstructions or approval.
Printed in U.S.A. (03/01) Bulletin #500023D $1
Distributed By:
Printed with vegetable inks on recycled paper. Please Recycle!
Backed By Our Worldwide Reputation For Quality, Accuracy and Advanced Design.
Backed By Our Worldwide Reputation ForQuality, Accuracy and Advanced Design.
Flow-Tech Industries4601 South Pinemont, Suite 100Houston, Texas 77041 Phone: 713.690.7474Fax: 409.882.0254