Vossloh-Schwabe Deutschland GmbH · Hohe Steinert 8 · 58509 Lüdenscheid · Germany · Phone +49 23 51/10 10 · Fax +49 23 51/10 12 17 · www.vossloh-schwabe.com LED Constant Current Drivers LEDLINE ECX ELECTRONIC CONSTANT CURRENT DRIVERS LED CONSTANT CURRENT DRIVERS Electronic converters for LED modules operated with constant current To ensure the safe operation of LEDs that are wired in series, the operating current must be limited to a constant value by the LED driver, Light-emitting diodes are semiconductor devices with a light-emitting p-n junction, Due to the specific diode characteristics, the current can only flow through an LED in one direction, Coupled with the special properties of a semiconductor, this non-linear behaviour can increase the current and power uptake of an LED as it heats up, If this effect is not limited, uncontrolled heating can finally destroy the semiconductor junction, For this reason, VS recommends using an external constant current driver to operate all constant current driven LED modules, To ensure that the same current flows through every LED, constant current driven LED modules can only be wired in series, The constant current source has to be selected to suit the respective application, i,e, it must supply the required current and also provide sufficient voltage for the LED string, The number of VS LED modules that can be connected to a single operating device is dependent on the forward voltage of the respective modules,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
LED CONSTANTCURRENT DRIVERSElectronic converters for LED modules operatedwith constant current
To ensure the safe operation of LEDs that are wired in series, theoperating current must be limited to a constant value by the LED driver,
Light-emitting diodes are semiconductor devices with a light-emitting p-n junction, Due to the specific diode characteristics, the current can only flow through an LED in one direction, Coupled with the special properties of a semiconductor, this non-linear behaviour can increase the current and power uptake of an LED as it heats up,
If this effect is not limited, uncontrolled heating can finally destroy the semiconductor junction, For this reason, VS recommends using an external constant current driver to operate all constant current driven LED modules, To ensure that the same current flows through every LED, constant current driven LED modules can only be wired in series,
The constant current source has to be selected to suit the respective application, i,e, it must supply the required current and also provide sufficient voltage for the LED string,
The number of VS LED modules that can be connected to a single operating device is dependent on the forward voltage of therespective modules,
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN –
06/
2018
LED Constant Current Drivers
Product Classification and Overview of LED DriversThe electronic constant current drivers are optimisedto operate constant current driven LED modules, Before connecting LED modules ensure that the power supply is disconnected from mains,
Most drivers are designed for DC-operation (mainsfrequency: 0 Hz) and can be used for emergencypower supplies,
Product overview by main application fieldsMain application Capacity range Output current DC Output voltage DC Ref. No. Version Current setting Dimming Max, service
Product guaranteeThe conditions for the product guarantee of the Vossloh-Schwabe Groupshall apply as published on our homepage (www.vossloh-schwabe.com).We will be happy to send you these conditions upon request.
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN –
06/
2018
LED Constant Current Drivers
Product Classification and Overview of LED DriversProduct overview by main application fieldsMain application Capacity range Output current DC Output voltage DC Ref. No. Version Current setting Dimming Max, service
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN –
06/
2018
LED Constant Current Drivers
Product Classification and Overview of LED DriversProduct overview by main application fieldsMain application Capacity range Output current DC Output voltage Ref, No, Version Current setting Dimming Max, service
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
5/43
– 0
6/20
18LED Constant Current Drivers – Office
ComfortLine LEDDrivers – Dimmable2x700 mA / max. 2x70 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: 0.95Standby losses: < 0.5 W
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current. Dimming range: 3 to 100% If no dimming interface is connected, brightnesswill stay at 100%.
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Push-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class ISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current output DC Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output without load at temperature temperature
50–60 Hz DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
6/43
– 0
6/20
18LED Constant Current Drivers – Office
ComfortLine LEDDrivers – Dimmable4x60 mA / max. 4x9 W500 mA / max. 107 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.95Standby losses: < 0.5 W
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current. Dimming range: 3 to 100%If no dimming interface is connected, brightnesswill stay at 100%.
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 HzPush-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
7/43
– 0
6/20
18LED Constant Current Drivers – Office
ComfortLine LEDDrivers – Dimmable2x350 mA / max. 2x20 W2x500 mA / max. 2x28.5 W2x700 mA / max. 2x40 Wand max. 2x70 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: 0.95
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current (M12) orwith an analogue dimming signal (M10/M11). Dimming range: 3 to 100%If no dimming interface is connected, brightnesswill stay at 100%.
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Push-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class ISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
8/43
– 0
6/20
18LED Constant Current Drivers – Office
ComfortLineLED Drivers2x250 mA / max. 2x14 W2x350 mA / max. 2x20 W2x500 mA / max. 2x28.5 W2x700 mA / max. 2x40 Wand max. 2x70 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9 C
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Push-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class ISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current output DC Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output without load at temperature temperature
50–60 Hz DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
9/43
– 0
6/20
18LED Constant Current Drivers – Office
ComfortLineLED Drivers4x60 mA / max. 4x9 W500 mA / max. 107 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed.Power factor at full load: > 0.96
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation (except 186305): 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Push-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
10/
43 –
06/
2018
LED Constant Current Drivers – Office
ComfortLineLED Drivers350 mA / max. 14 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed.Power factor at full load: 0.55 C
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 176–264 V DC, 0 HzPush-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
12/
43 –
06/
2018
LED Constant Current Drivers – Office
EasyLine LED Drivers– with SelectableCurrent150/250/350 mA / max. 14 W500/600/700 mA / max. 21 WThe linear LED constant-current drivers are designedfor use in office and retail lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed.Power factor at full load: > 0.94
Selectable current outputThe required current output can be chosen byselecting the respective pin at the output terminal.
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class ISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class ISELV (186429)Product guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
15/
43 –
06/
2018
LED Constant Current Drivers – Retail
PrimeLine LEDDrivers – with Pro-grammable Current350–700 mA / max. 24 W and max. 37 WCompact casing shape with integrated cord gripoptional for built-in or independent operation.
Electrical characteristicsSecondary side switching of LED modulesis allowed (hot wiring).Power factor at full load: > 0.95Standby losses: < 0.5 W
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current. Dimming range: 1 to 100% If no dimming interface is connected, brightnesswill stay at 100%.
ProgrammabilityThe output current can be freely adjustedin 1 mA steps between 350 mA and700 mA (factory setting: 350 mA).An iProgrammer (Ref. No. 186428) anda PC running the respective VS softwareare required for programming purposes.
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)With integrated through-wiringPush-in terminals: 0.2–1.5 mm²
Max. Type Ref. No. Mains voltage Mains Current output DC Factory Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current programmable setting output without load at temperature temperature
50–60 Hz DC DC full load ta tcW V mA mA mA V V % (230 V) °C °C g
Expected service life timeat operation temperatures at tc point
Operation Ref. No.
current all types
all 65 °C 75 °C
hrs. 100,000 50,000
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
16/
43 –
06/
2018
LED Constant Current Drivers – Retail
ComfortLine LEDDrivers – Dimmable700 mA / max. 24 W and max. 37 WCompact casing shape with integrated cord gripoptional for built-in or independent operation.
Electrical characteristicsSecondary side switching of LED modulesis allowed (hot wiring).Power factor at full load: > 0.9Standby losses: < 0.5 W
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current. Dimming range: 1 to 100%If no dimming interface is connected,brightness will stay at 100%.
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)With integrated through-wiringPush-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
17/
43 –
06/
2018
LED Constant Current Drivers – Retail
ComfortLine LEDDrivers – Dimmable700 mA / max. 24 WCompact casing shape with integrated cord gripoptional for built-in or independent operation.
Electrical characteristicsSecondary side switching of LED modulesis allowed (hot wiring).Power factor at full load: > 0.9
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current. Dimming range: 1 to 100%If no dimming interface is connected, brightnesswill stay at 100%.
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)With integrated through-wiringPush-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
18/
43 –
06/
2018
LED Constant Current Drivers – Retail
ComfortLine LEDDrivers700 mA / max. 37 W
Electrical characteristicsSecondary side switching of LED modulesis allowed. (hot wiring) Power factor at full load: > 0.9
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)With integrated through-wiring for L/N/PEPush-in terminals: 0.25–2.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
19/
43 –
06/
2018
LED Constant Current Drivers – Retail
ComfortLineLED Drivers700 mA / max. 24 W and max. 37 WCompact casing shape with integrated cord gripoptional for built-in or independent operation.
Electrical characteristicsSecondary side switching of LED modulesis allowed (hot wiring).Power factor at full load: > 0.9
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)With integrated through-wiringPush-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
20/
43 –
06/
2018
LED Constant Current Drivers – Retail
EasyLine LED Drivers500 mA / max. 25 W700 mA / max. 35 W1050 mA / max. 35 WCompact casing shape with integrated cord gripoptional for built-in or independent operation.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
Safety featuresTemporary electronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
21/
43 –
06/
2018
LED Constant Current Drivers – Residential
ComfortLine LEDDrivers – Dimmable700 mA / max. 30 W1050 mA / max. 37,8 W
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
Dimming (except 186393)Dimmable (anaglogue) with phase-cuttingtrailing-edge dimmerMinimum dimmer load has to be observed.The compatibility of the driver and the dimmerhas to be confirmed prior to installation to avoideflickering and/or noises.
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current output Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current DC output without load at temperature temperature
DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
22/
43 –
06/
2018
LED Constant Current Drivers – Residential
ComfortLineLED Drivers350 mA / max. 8.75 W
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.6
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Screw terminals: 1.5 mm²
Safety featuresProtection against transient main peaksup to 1 kV (between L and N)Electronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
23/
43 –
06/
2018
LED Constant Current Drivers – Residential
EasyLine LED Drivers– Dimmable150–700 mA / max. 6–36 W
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.85
DimmingDimmable (anaglogue) with phase-cuttingtrailing-edge dimmer.Minimum dimmer load has to be observed.The compatibility of the driver and the dimmerhas to be confirmed prior to installation to avoideflickering and/or noises.
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output voltage current output output without load at temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
24/
43 –
06/
2018
LED Constant Current Drivers – Residential
EasyLine LED Drivers700 mA / max. 5.2 WFor applications according to EN 60335
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.5
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzPre-assembled connection leads primary: 2x0.75 mm², length: 180 mm secondary: 2x0.5–0.75 mm², length: 180 mm
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
25/
43 –
06/
2018
LED Constant Current Drivers – Residential
EasyLine LED Drivers350 mA / max. 7 W700 mA / max. 5.6 W
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.5
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzPre-assembled connection leads primary: 2x0.75 mm², length: 180 mm secondary: 2x0.5–0.75 mm², length: 180 mm
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Products under development; preliminary technical datas
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
27/
43 –
06/
2018
LED Constant Current Drivers – Residential
EasyLine LED Drivers350 mA / max. 12.6 W and 20 W500 mA / max. 15 W700 mA / max. 20.3 W and 25.2 WThe LED constant-current drivers are designedfor use in residential lighting.
Electrical characteristicsSecondary side switching of LED modulesis not allowed.Power factor at full load: > 0.5 or > 0.95 (186353)
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVProduct guarantee: 5 yearsat recommended operation temperature
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
30/
43 –
06/
2018
LED Constant Current Drivers – Street
PrimeLine LEDDrivers – Dimmablewith ProgrammableCurrent350–1050 mA / max. 150 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.95Constant lumen output
DimmingThe dimming function is achieved byapplying an analogue dimming signalto the nominal current.Dimming range: 10 to 100% If no dimming interface is connected, brightnesswill stay at 100%.
ProgrammabilityThe output current can be freely adjustedin 1 mA steps between 350 mA and1050 mA (factory setting: 350 mA).An iProgrammer (Ref. No. 186428) anda PC running the respective VS softwareare required for programming purposes.
Expected service life timeat operation temperatures at tc point
Operation Ref. No.
current all types
350–1050 mA 70 °C 80 °C
hrs. 100,000 50,000
Safety featuresProtection against transient main peaksup to 6 kV (between L and N)Double isolatedElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP65Protection class IIThe LEDs are thermally protected bythe driver's NTC interface, whichensures the current will be reducedwhen a critical temperature is reachedProduct guarantee: 5 years
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
31/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLineLED Drivers – forPower Reduction700/400 mA / max. 150 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.They provide a simple power-reduction option byconnecting a further phase, which makes it possibleto switch between 700 mA and 400 mA.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.95
Power reductionThe nominal current output will be reducedby connecting the control phase (LST)to 57% (analogue step dimming).Connecting L (black) and LST (orange) tothe mains voltage reduces output by loweringthe output current. If this function is not used,an additional terminal should be providedin the luminaire to fix the LST wire.
Connection detailsMains voltage: 220–277 V ± 10%Mains frequency: 50–60 HzK37: Push-in terminals: 0.75–2.5 mm²K37 with cord grip: Pre-assembled connection leads: primary: 5x1 mm², 200 mm secondary: 2x1.5 mm², 200 mm Suitable for independent operation when capable connector acc. to EN 60598 is used.
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Power reduction can be effected with VS Power Switches PR12 K LC and PR12 K D.These power switches are used to switch the 230-V power reduction input on the LED driver of a luminaire.
Expected service life timeat operation temperatures at tc point
Operation Ref. No.
current all types
all 65 °C 75 °C
hrs. 100,000 50,000
Safety featuresProtection against transient main peaksup to 3 kV (between L and N) andup to 4 kV (between L, N and PE)Electronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20 or IP66 (K37 with cord grip)Protection class IProduct guarantee: 5 years
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
32/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLine LEDDrivers – Dimmable700 mA / max. 75, 100 and 150 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
DimmingThe dimming function is achieved by applying ananalogue dimming signal to the nominal current.Dimming range: 10 to 100% If no dimming interface is connected, brightnesswill stay at 100%.
Safety featuresProtection against transient main peaksup to 6 kV (between L and N)Electronic short-circuit protectionOverload protectionOvertemperature protection (186402)Protection against "no load" operationDegree of protection: IP65Protection class IIProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
33/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLine LEDDrivers – Dimmable1050 mA / max. 60 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.96
DimmingThe dimming function is achieved by applying ananalogue dimming signal to the nominal current.Dimming range: 10 to 100% If no dimming interface is connected, brightnesswill stay at 100%.
Connection detailsMains voltage: 220–240 V ± 10%Mains frequency: 50–60 HzPre-assembled connection leads: primary: 2x0.75 mm², length: 300 mm secondary: 6x0.75 mm², length: 300 mm
Safety featuresProtection against transient main peaksup to 4 kV (between L and N)Electronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP67Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
34/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLine LEDDrivers – Dimmable700 mA / max. 38.5 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.96
DimmingThe dimming function is achieved by applyinganalogue dimming signal to the nominal current. Dimming range: 10 to 100% If no dimming interface is connected, brightnesswill stay at 100%.
Connection detailsMains voltage: 120–277 V ±10%Mains frequency: 50–60 HzPre-assembled connection leads: primary: 2x0.75 mm², length: 228 mm secondary: 4x0.75 mm², length: 228 mm
Safety featuresProtection against transient main peaksup to 6 kV (between L and N)Electronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP54Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
35/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLineLED Drivers – forPower Reduction700/400 mA / max. 75, 100 and 150 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.They provide a simple power-reduction option byconnecting a further phase, which makes it possibleto switch between 700 mA and 400 mA.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
Power reductionThe nominal current output will bereduced by connecting the controlphase (LST) to 57%.Connecting L (black) and LST (orange) tothe mains voltage reduces output by loweringthe output current. If this function is not used,an additional terminal should be providedin the luminaire to fix the LST wire.
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
Expected service life timeat operation temperatures at tc point
Operation Ref. No.
current 186397, 186509 186398
700 mA 75 °C 85 °C 70 °C 80 °C
hrs. 100,000 50,000 100,000 50,000
Safety featuresProtection against transient mainpeaks up to 6 kV (between L and N)Electronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP65Protection class IIProduct guarantee: 5 years
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
36/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLineLED Drivers 700 mA / max. 38.5 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
Connection detailsMains voltage: 120–277 V ±10%Mains frequency: 50–60 HzPre-assembled connection leads: primary: 2x0.75 mm², length: 228 mm secondary: 2x0.75 mm², length: 228 mm
Safety featuresProtection against transient mainpeaks up to 6 kV (between L and N)Electronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP54Protection class IISELVProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
37/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLineLED Drivers700 mA / max. 150 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
Connection detailsMains voltage: 120–277 V ±10%Mains frequency: 50–60 HzPre-assembled connection leads: primary: 2x0.75 mm², length: 450 mm secondary: 2x0.75 mm², length: 180 mm
Safety featuresProtection against transient main peaksup to 6 kV (between L and N)Electronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP65Protection class IIProduct guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
38/
43 –
06/
2018
LED Constant Current Drivers – Street
ComfortLineLED Drivers 350 mA / max. 40 W700 mA / max. 40 W1050 mA / max. 40 WThese electronic LED constant current drivers areespecially designed for use in street lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.9
Safety featuresProtection against transient main peaksup to 4 kV (between L and N)Electronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class IIProduct guarantee: 5 years
Products under development; preliminary technical datas
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency Ambient Casing Weight
output 50–60 Hz current output output without load at temperature temperature
DC DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
39/
43 –
06/
2018
LED Constant Current Drivers – Industry
ComfortLine LEDDrivers – Dimmable700 mA / max. 112 W1050 mA / max. 126 WWith 12 V interfaceThese electronic LED constant current drivers aredesigned for use in industrial hall lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.95Standby losses: < 0.5 W
DimmingThe dimming function is achieved by applyinga PWM signal to the nominal current.Dimming range: 3 to 100%If no dimming interface is connected,brightness will stay at 100%.
Connection detailsMains voltage: 220–240 V ± 10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Push-in terminals: 0.2–1.5 mm²
Safety featuresElectronic short-circuit protectionOverload and overtemperatureprotectionProtection against "no load" operationDegree of protection: IP20Protection class IThe LEDs are thermally protected bythe driver's NTC interface, whichensures the current will be reducedwhen a critical temperature is reached.Product guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency 12 V Ambient Casing Weight
output 0 Hz, current output output without load at interface temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) max. 2 W °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
40/
43 –
06/
2018
LED Constant Current Drivers – Industry
ComfortLine LEDDrivers – Dimmableand Adjustable900/1050/1200/1400 mA / max. 60.2 WThe dial can be used to set the current outputto 900 mA (1), 1050 mA (2), 1200 mA (3)or 1400 mA (4).
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.95
DimmingThe dimming function is achieved by applyinga PWM signal.Dimming range: 3 to 100%If no dimming interface is connected, brightnesswill stay at 100%.
Safety featuresElectronic short-circuit protectionOverload protectionProtection against "no load" operationDegree of protection: IP20Protection class ISELVThe LEDs are thermally protected by the driver'sNTC interface, which ensures the current willbe reduced when a critical temperature isreached. Product guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current output Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current DC output without load at temperature temperature
50/60 Hz DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
41/
43 –
06/
2018
LED Constant Current Drivers – Industry
ComfortLine LEDDrivers – Dimmableand Adjustable350/500/600/700 mA / max. 39.9 WThe dial can be used to set the current outputto 350 mA (1), 500 mA (2), 600 mA (3)or 700 mA (4).
Electrical characteristicsSecondary side switching of LED modulesis not allowed.Power factor at full load: 0.95
DimmingThe dimming function is achieved by applyinga PWM signal.Dimming range: 3 to 100%If no dimming interface is connected, brightnesswill stay at 100%.
Safety featuresElectronic short-circuit protectionOvervoltage protection: 2 kV acc. to EN 51000-4-5Overload protectionProtection against "no load" operationDegree of protection: IP20Protection class IISELVThe LEDs are thermally protected bythe driver's NTC interface, which ensuresthe current will be reduced when a criticaltemperature is reached. Product guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current output Voltage Max. voltage Efficiency Ambient Casing Weight
output 0 Hz, current DC output without load at temperature temperature
50/60 Hz DC DC full load ta tcW V mA mA V V % (230 V) °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
42/
43 –
06/
2018
LED Constant Current Drivers – Industry
ComfortLineLED Drivers700 mA / max. 112 W1050 mA / max. 126 WWith 12 V interfaceThese electronic LED constant current drivers aredesigned for use in industrial hall lighting systems.
Electrical characteristicsSecondary side switching of LED modulesis not allowed. Power factor at full load: > 0.95
Connection detailsMains voltage: 220–240 V ±10%Mains frequency: 50–60 HzDC operation: 198–264 V DC, 0 Hz (can be reduced to 176 V with reduced service life time)Push-in terminals: 0.2–1.5 mm2
Safety featuresElectronic short-circuit protectionOverload and overtemperature protectionProtection against "no load" operationDegree of protection: IP20Protection class IThe LEDs are thermally protectedby the driver's NTC interface, whichensures the current will be reducedwhen a critical temperature is reached. Product guarantee: 5 years
Max. Type Ref. No. Mains voltage Mains Current Voltage Max. voltage Efficiency 12 V Ambient Casing Weight
output 0 Hz, current output output without load at interface temperature temperature
50–60 Hz DC DC DC full load ta tcW V mA mA V V % (230 V) max. 2 W °C °C g
The values contained in this data sheet can change due to technical innovations. Any such changes will be made without separate notification.
LED
Con
stant
-cur
rent
Driv
ers_
EN–
43/
43 –
06/
2018
LED Constant Current Drivers – Industry
iProgrammerFor programming LED driversThe iProgrammer is designed to let you configureLED drivers using the 3C function.
Using DALI commands, the iProgrammer enablesvarious functions to be configured on all VSLED drivers that feature the "3C" symbol.As an example, not only can the current be set toa precise level, but programming functions for thestreet lighting zone can also be transferred.Please refer to the manual at product pageunder www.vossloh-schwabe.com for detailedconfiguration procedures.
Technical notesConfiguration interface: DALIAmbient temperature ta: 5 to 50 °CPush-in terminals: 0.2–1.5 mm²Degree of protection: IP20
ConnectionsMains connection: 220–240 V AC/50–60 HzMax. power consumption: 5 WUSB 2.0
Software downloadSee product page under www.vossloh-schwabe.com
FunctionsConfiguring "3C" LED drivers
Type Ref. No. Connection to PC/Laptop Functions Dimensions Weight
mm (LxWxH) g
iProgrammer 186428 USB 2.0 Configuring "3C" LED drivers 123.4x79.4x32.6 135