590 Accessories Sensing Guide Vision Sensors 3Z4S-LT Smart Sensors Other Information Peripheral Devices Vision Systems LED Lighting System 3Z4S-LT Next-generation MG-Wave ® LED Illumination Combines with the Vision Sensor to Provide New Solutions For wide variety of applications. Long life span and high-intensity illumination. Be sure to read Safety Precautions on Page 597. Features Using MG-Wave ® Sensing Control Method (Patent Pending) • Without mounted resistors the temperature has been reduced by 20°C In the constant-voltage system, any kind of heat dissipation paradoxically requires LED lights to have a heat-generating limiting resistor. The MG-Wave series has adopted a constant-current technology that frees LED lights from having a limiting resistor, thereby achieving the industry's highest thermal characteristics. • Luminous intensity increased by controlling heat generation In LED lighting, the heat factor cannot be separated from the luminous intensity. Using the constant current system explained above in combination with our proprietary heat dissipation system, we achieved an outstanding reduction in heat generation and a 40-percent increase in luminous intensity compared to the conventional product, the MDRL-CW31. The MG-Wave series has the patent-pending detection circuit incorporated in the light. It reads the signal to control the rated current that is adjusted according to the number of LEDs in every lighting module. Therefore, it can be used for any type of lighting, such as in the constant voltage configuration, if it is within the maximum current capacity of the power source. Constant Current Detection Control High-intensity Illumination Easy to Use Constant current type/white (with heat dissipation): 114 LEDs The diagram depicts the temperature of the three LED substrates for thirty minutes of operation after full acclimatization to the temperature of a constant temperature bath maintained at 40°C. A B C 100 95 90 85 80 75 70 65 60 55 50 45 40 0 5 10 15 20 25 30 35 Temperature around the LED lead (°C) Elapsed time (mins) The MG-Wave series A B C Constant voltage type/white (without heat dissipation): 114 LEDs with resistors (equivalent to conventional products) Constant voltage type/white (with heat dissipation): 114 LEDs with resistors (equivalent to conventional products) The diagram depicts the lighting intensity of the four test products for thirty minutes of lighting after full acclimatization to the temperature of a constant temperature bath maintained at 40°C. 14,000 12,000 10,000 8,000 0 40 30 10 20 A B C D Constant current type/white (with heat dissipation): 114 LEDs Duration (mins) Lighting intensity lx A B C D The MG-Wave Series Constant current type/white (without heat dissipation): 114 LEDs with resistors (equivalent to conventional products) Constant current type/white (with heat dissipation): 114 LEDs with resistors (equivalent to conventional products) Constant current type/white (without heat dissipation): 114 LEDs Schematic diagram of a lighting system and a power source with a detection circuit Lighting capacity information Supplying the required capacity A A A Light Constant current power supply Detection circuit Lighting capacity Power supply capacity
12
Embed
LED Lighting System 3Z4S-LT - Cebu Champion Hardware Sensors/3Z4S-L… · LED Lighting System 3Z4S-LT ... 100 95 90 85 80 75 70 65 60 55 50 45 40 ... Razor edge Electrodes on liquid
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
590
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
LED Lighting System
3Z4S-LTNext-generation MG-Wave ® LED Illumination Combines with the Vision Sensor to Provide New Solutions
For wide variety of applications.Long life span and high-intensity illumination.
Be sure to read Safety Precautions on Page 597.
Features
Using MG-Wave® Sensing Control Method (Patent Pending)
• Without mounted resistors the temperature has been reduced by 20°CIn the constant-voltage system, any kind of heatdissipation paradoxically requires LED lights tohave a heat-generating limiting resistor. TheMG-Wave series has adopted a constant-currenttechnology that frees LED lights from having alimiting resistor, thereby achieving the industry'shighest thermal characteristics.
• Luminous intensity increased by controlling heat generationIn LED lighting, the heat factor cannot beseparated from the luminous intensity. Using theconstant current system explained above incombination with our proprietary heat dissipationsystem, we achieved an outstanding reduction inheat generation and a 40-percent increase inluminous intensity compared to the conventionalproduct, the MDRL-CW31.
The MG-Wave series has the patent-pendingdetection circuit incorporated in the light. It readsthe signal to control the rated current that isadjusted according to the number of LEDs inevery lighting module. Therefore, it can be usedfor any type of lighting, such as in the constantvoltage configuration, if it is within the maximumcurrent capacity of the power source.
Constant Current Detection Control
High-intensity Illumination
Easy to Use
Constant current type/white (with heat dissipation):114 LEDs
The diagram depicts the temperature of the three LED substrates for thirty minutes of operation after full acclimatization to the temperature of a constant temperature bath maintained at 40°C.
A
B
C
100959085807570656055504540
0 5 10 15 20 25 30 35
Tem
pera
ture
aro
und
the
LED
lead
(°C
)
Elapsed time (mins)
The MG-Wave series
A
BC
Constant voltage type/white(without heat dissipation):114 LEDs with resistors (equivalent to conventional products)
Constant voltage type/white (with heat dissipation):114 LEDs with resistors (equivalent to conventional products)
The diagram depicts the lighting intensity of the four test products for thirty minutes of lighting after full acclimatization to the temperature of a constant temperature bath maintained at 40°C.
14,000
12,000
10,000
8,0000 403010 20
A
B
CD
Constant current type/white(with heat dissipation): 114 LEDs
Duration (mins)
Ligh
ting
inte
nsity
lx
A
B
C
D
The MG-Wave Series
Constant current type/white(without heat dissipation): 114 LEDs with resistors(equivalent to conventional products)
Constant current type/white(with heat dissipation): 114 LEDs with resistors(equivalent to conventional products)
Constant current type/white(without heat dissipation): 114 LEDs
Schematic diagram of a lighting system and a power source with a detection circuit
Lighting capacity information
Supplying the required capacityAA
A
LightConstant
current powersupplyDetection circuit
Lighting capacityPowersupply
capacity
3Z4S-LT
591
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
Direct Ring Light MDRL Series
Low Angle Ring Light MLRL Series
Simulated Coaxial Episcopic Light MSCL Series
Shadowless Ring Light MSRL Series
• High-luminance LEDs deployed at high density to produce 360-degree shadow-free illumination.
• Standard type of LED lighting for a wide range of applications.
• Ability to select the model that matches our lenses.
Applications• Substrate/PC board positioning and chip component
inspection• LCD alignment and plastic container inspection• Label, mounting, and IC impress inspection
• Providing 360-degree illumination for reflective objects from a low angle without producing reflections. Ideal for slightly uneven surfaces and scratches.
Applications• BGA solder ball position, shape, and area inspection• Laser marking read• Wafer and glass board inspection for scratches and
stains• Inspection for edge extraction and others
• Produces simulated even coaxial lighting for lenses without coaxial episcopic illumination.
Applications• Alignment inspection of wafer, metal surface, film,
LC, glass, and other mirror-finished materials• PCB pattern inspection
• Soft, even, diffused lighting on shiny objects.• Best for preventing the halo effect.
Applications• Cap side and internal inspection for stains• Wafer appearance inspection• Solder and connector pitch inspection
Button components formobile phone
Button components formobile phone
Metal parts
D-sub connector
3Z4S-LT
592
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
Bar Light MBRL Series
Edge-type Backlight MEBL Series
Direct Backlight (Shell Type) MDBL Series
CCTV Lens ML Series
• High-intensity LED are arranged in an array form and oblique illumination from an arbitrary angle can be obtained for each type of work.
Applications• LED flow detection• Complicated shape recognition• Molding crack inspection• Electronic part shape recognition and size measurement• Direct-tube fluorescent lamp replacement
• Thin, compact design for the advantage of saving space.
• Even lighting with the use of Moritex’s proprietary light-guiding diffusion plate, film, and surface diffusion.
• Ideal for highly reflective objects.
Applications• Lead frame inspection• Visual inspection of electronic parts• Bend lead inspection for GFPs, QSPs and SOPs• Inspection for dirt on clear film• Different silhouette observation
• Higher luminance than the edge-type with lamp-type LCDs mounted immediately beneath the light surface.
Applications• Lead frame inspection• Visual inspection of electronic parts• Bend lead inspection for GFPs, QSPs and SOPs• Inspection for dirt on clear film• Different silhouette observation
• A wide range of products from f=6mm to 50mm.• Focus and iris are adjustable using attached locking screws.• Camera mount: C mount.
CCTV (Closed Circuit Television) lenses were developed to recognize images in a wide area.All models have an iris and focus adjustment that you can set as required with the includedlocking screws (*1). Using optional close-up ring allows for macro photographing (*2).*1. Not designed to be vibration proof.*2. Tolerances of lenses may increase and image quality may worsen as a result.
MG-Wave® Series Power Supplies for MG-Wave SeriesNEW MLEK SeriesA080W Analog Series (Support up to total 0.8 A)A230W Digital Series (Support up to total 2.3 A)
Ordering Information/Specifications
LightingsDirect Ring Light
Low Angle Ring Light
Simulated Coaxial Episcopic Light
• Operates with power supplied from the Camera Head.• No need of light-emission control.• Minimal wiring by simply connecting the Camera and Illumination Device with a single cable.
• These constant-current Power Supplies are available for use with our widely applicableIllumination Series, to match the current consumption levels of the Illumination Device beingused.
• Proper heat control ensures that the maximum advantages of each Illumination Device will be gained, and functions are provided for external output control.
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MDRL-CR16 Red 0.24 65 A 080 Series ○
MDRL-CR31 Red 0.36130
A 080 Series ○
MDRL-CW31 White 0.55 A 080 Series ○
MDRL-CR50 Red 0.64180
A 080 Series ○
MDRL-CW50 White 0.96 A 230 Series ×
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MLRL-CR48 Red 0.30 110 A 080 Series ○
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MSCL-CR39 Red 0.16 160 A 080 Series ○
MSCL-CR56-B Red 0.33 320 A 080 Series ○
3Z4S-LT MDRL-C * @ @Internal diameter of the ring (mm)
Luminescent color (Red=R, White=W)
3Z4S-LT MLRL-C * @ @ @Internal diameter of the ring (mm)
Luminescent color (Red=R)
3Z4S-LT MSCL-C * @ @ - △
Box heightLuminescent color (Red=R)
Revision code
Model Suitable camera3Z4S-LT MLEK-C080E1LS F150-S1A, F160-S23Z4S-LT MLEK-C100E1TS FZ-SC3Z4S-LT MLEK-C100E1TSX ZFX-S/SC
3Z4S-LT
594
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
Shadowless Ring Light
Bar Light
Edge-type Backlight
Direct Backlight (Shell type)
CCTV Lens
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MSRL-CR44 Red 0.57 270 A 080 Series ○
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MBRL-CR7530 Red 0.36 120 A 080 Series ○MBRL-CW13015 White 0.53 85 A 080 Series ○
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MEBL-CR10080 Red 0.32 230 A 080 Series ○
Model Luminescent color
Max. rated current IFM (A) Weight (g) Power supply Connection to strobe controller
MDBL-CR70 Red 0.48 190 A 080 Series ○
ModelFocal
distance f (mm)
Focus (F No.) Field of view(V × H)
Closest distance
(m)
Filter screw
Weight (g)
Total length (mm)
Maximum compatible
CCDMount
3Z4S-LE ML-0614 6 F1.4 to Close 42.3° × 54.6°0.2
M27 P0.5 60
30 1/2 inch
C Mount
3Z4S-LE ML-0813 8 F1.3 to Close 45.0° × 57.8° M25.5 P0.534.5
2/3 inch3Z4S-LE ML-1214 12
F1.4 to Close21.9° × 29.0° 0.3
M27 P0.5
1/2 inch3Z4S-LE ML-1614 16 23.0° × 30.4° 0.4 40
24.52/3 inch
3Z4S-LE ML-2514 25 21.6° × 28.5°0.5
45 1 inch3Z4S-LE ML-3519 35 F1.9 to Close 10.8° × 14.4° 50 29
2/3 inch3Z4S-LE ML-5018 50 F1.8 to Close 7.9° × 10.5° 1 M30.5 P0.5 60 37
3Z4S-LT MSRL-C * @ @Internal diameter of the ring (mm)
Luminescent color (Red=R)
3Z4S-LT MBRL-C * @ @ @ @Size (length and width)
Luminescent color (Red=R, White=W)
3Z4S-LT MEBL-C * @ @ @ @Size (length and width)
Luminescent color (Red=R)
3Z4S-LT MDBL-C * @ @ @ @Size (length and width)
Luminescent color (Red=R)
3Z4S-LT
595
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
Ratings and SpecificationsStrobe Controllers
*1. Depends on the illumination used.*2. Strobe intensity adjustment and variable range.
Item Model 3Z4S-LT MLEK-C080E1LS 3Z4S-LT MLEK-C100E1TS 3Z4S-LT MLEK-C100E1TSXNo. of outputs 1-channel output
Output current 0.83 A max. (when using 0.8 A illumination) *1 1.0 A max. (when using 1.0-A illumination) *1
Output control method Constant current control
Output form Strobe output (synchronized with rising edge trigger)Output adjustment function Manual dial only External communications setting only *2
Variable output range 0 to 100%
Strobe emission time 8.3 ms (standard) Automatically set by FZ Controller Automatically set by ZFX Controller
Usage environment Indoor use at a max. altitude of 2,000 m, with no inflammable or corrosive gases present, and no adhesion of foreign matter
Ambient temperature and humidity
0 to 45°C, 80% up to 31°C and then dropping linearly to 50% at 40°C
Storage temperature and humidity -20 to 85°C, 20 to 80% humidity (with no condensation)
Mounting method Connected and mounted to F160-S2 or F150-S1A Camera
Connected and mounted to FZ-SC Camera
Connected and mounted to ZFX-S/SC Camera
Cooling method Natural air coolingDegree of protection IP30 (IEC 60529)Weight Approx. 80 gExtension Cable (sold separately) M-RCB4@@L (4-pin Extension Cable) (indicate length in the 2 square boxes (@@): 02 = 2 m, 03 = 3 m)
3Z4S-LT
596
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
Power Supplies for MG-Wave ® SeriesNEW MLEK SeriesA080/230W Series
* The AC power cable that is enclosed depends on the voltage. Be sure to use a suitable power supply for the country in which the Controller is used.
Item Model MLEK-A080W1LR-100V MLEK-A080W1LR-200V MLEK-A230W2LRDB-100V MLEK-A230W2LRDB-200VAC Type * 100 V 200 V 100 V 200 V
Output Single-channel output of 0.8A(for connection to all lights except the MCEP Series)
Two-channel maximum, output of 2.3A for each channel (for connection to all lights except the MCEP Series)
Input voltage 100 to 240V AC 50/60HzInput current 0.3/0.15A (at AC 100/240V) 0.7/0.4A (at AC 100/240V)
Surge current 15 A or lower (at 100 VAC)35 A or lower (at 240 VAC)
Operating temperature 0 to 45°C
Output system Continuous DC outputOutput control system Constant current control (the current can be changed)
External light control Supported (0 to 5V) Supported (for each channel, 8-bit digital)Lighting ON/OFF function Supported (photocoupler insulation)
Error output Supported (photocoupler insulation, control error)Cooling system Natural air cooling Forcible air coolingInstallation Horizontal installation on the rubber supports at the bottom of the unitWeight Approx. 1 kg Approx. 1.4 kg
AC200V Cable
CE (PS) E/UL/CSA (PS) E
AC100V Cable
Adapter(for use in Japan only)
3Z4S-LT
597
Accessories
SensingGuide
Vision Sensors
3Z4S-LT
SmartSensors
OtherInformation
PeripheralDevices
VisionSystems
Connection Specifications and I/O Circuit DiagramsNEW MLEK SeriesA080W Analog Series (Support up to total 0.8A)
A230W Digital Series (Support up to total 2.3A)
Safety PrecautionsRefer to Warranty and Limitations of Liability on page F-2.
This product is not designed or rated for ensuring safety of persons. Do not use it for such purpose.
Do not use the product in atmospheres or environments that exceed product ratings.