LED-FLIR20sw LED-FLIR20gr LED-FLIR20ws
20 watts High Power LED floodlight with IR motion sensor
Specifications:
Light Power supply: 180 – 240 V AC Supply frequency: 50 Hz
Output: max. 20 watts Protection class: IP 54 LEDs: 12 x 1.6 watts
Colour temperature: 6,200 – 6,700 K Luminous flux: 825 lm Beam
angle: 100° Permitted humidity: < 93 % Ambient temperature: -10
°C to +40 °C Dimensions (HxBxD): 189 x 177 x 180 mm Weight: approx.
1.6 kg
Sensor Installation height: 1.8 m – 3.5 m PIR angle of
detection: 180° Range of detection: 10 – 12 m Twilight value: 3 Lux
– 2,000 Lux Duty cycle: min. 8 sec. +/- 3 sec. max. 7 min. +/- 2
min. Energy consumption: 0.45 watts (standby: 0.1 watts)
4
LED-FLIR20...
▪ 20 watts LED light is equivalent to 150 watts halogen light▪
12 high power LEDs▪ low energy consumption ▪ lasts 100x longer than
halogen lamps▪ automatic activation via twilight sensor and
infrared motion sensor▪ environmentally friendly▪ IP54 protected
against splash water
What to do if… ... the floodlight does not turn on a) check
power supply b) check operating display: if it flashes every 4
seconds and twice every second after thisc) check, whether the
operating display flashes more quickly after the signal has been
received d) check whether the set twilight value is consistent with
the ambient brightness
... the IR sensor is not sensitive enough a) check whether items
are in the vicinity of the area of detection, which impair the
reception of the signal b) check ambient temperaturec) check
whether the source of the signal is in the area of detectiond)
check height of installation e) check direction of motion
.... the floodlight does not turn offa) check detection area for
continuous signals b) check whether duty cycle is set to max. c)
check whether power supply is consistent with the technical datad)
check whether appliances are in the immediate vicinity of the
floodlight, which change the ambient temperature, such as central
heating or air conditioning
WARNING! Please observe the following advice:- Installation
should only be carried out by an electrician or trained member of
staff.- Do not remove the plug or use the appliance if the cable is
damaged.- This floodlight should not be exposed to shocks.- No
items should be kept in the area of detection, which might impair
the area of detection.- This floodlight should not be installed in
the vicinity of appliances, which have an impact on the ambient
temperature, such as central heating or air conditioning.- For your
own safety: do not open casing if appliance does not function after
installation. - To avoid damage to the product: please use 6A
safety for installation.
This product is a high power floodlight with a highly sensitive
infrared sensor, inte-grated circuit (IC), as well as SMT
technology. This practical automatic floodlight is user friendly,
safe and energy efficient. Its operation is based on the reception
of infrared light in a vertically and horizontally defined area of
detection. Immedia-tely after entering the detection area, the
floodlight will be activated. The ambient light sensitivity can be
set for “sun“ or “moon“. The installation is easy and the scope of
applications is versatile. The operating display is lit when the
appliance is switched on and the IR sensor is activated.
Operation - The area of detection (see diagrams) can be defined
horizontally and vertically and can be set for the relevant
requirements. - The twilight value can be set individually. If the
ambient light drops below the twilight value and motion are
detected, the floodlight will be activated. If the setting is set
for “sun” (= max.), the floodlight is active day and night; if the
setting is set for “moon“ (= min.) the light will only be active
from a minimum brightness of 3 Lux (see function test). - Operating
display: after being turned on, the operating display will flash
once every 4 seconds, during a signal is received, the display will
flash twice every second. - The duration of the duty cycle starts
afresh with every signal. - The duration of the duty cycle, for
which the light will be turned on following activation can be set
for anything between a minimum of approx. 8 +/- 3 seconds to a
maximum of 7 minutes +/- 2 minutes.
Installation (see diagram)- Turn power off or pull plug. - Fix
mounting bracket in desired position using screws and rawl plugs. -
Connect power
Functional test- Turn twilight value control clockwise to “Max.”
(=sun), turn permanent activation control clockwise to „min.“. -
After activation, the light will be off and the operating display
will flash once every 4 seconds. After 5 – 10 seconds, the
floodlight will turn on; the display will flash twice every second.
If no signal is received, the twilight value control will turn off
after 5 – 30 seconds and the display will return to flashing every
4 seconds. - Approx. 5 – 10 seconds after the signal was received,
the light will turn on again and the will flash twice every second.
The light will turn off again after 5 – 15 seconds. - Turn the
twilight value control counter clockwise to min. (=moon). If the
ambient light is brighter than 3 Lux, the floodlight will not turn
on again after having been turned off. Cover the sensor with
something suitable for blocking the light, such as a towel, etc.;
the floodlight will turn on again. If no source for a signal is
present in the area of detection, the floodlight will turn off
again after 5 – 15 seconds.
LED-FLIR20... LED-FLIR20...
2 3
Ledino Deutschland GmbHAlbert-Einstein-Ring 2714532 Kleinmachnow
(Berlin)GermanyTelefon: +49 33203 810-0 Telefax: +49 33203
[email protected], www.ledino.com
Im Zollhafen 2450678 KölnGermanyTelefon: +49 221
888989-0Telefax: +49 221 [email protected],
www.ledino.com