LEAD ACID BATTERY CHARGER SBC - 2110 / 2115 / 2120 12V 3-Stage IUoU Battery Charger with Power Supply Mode Selection anson M ◘ All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa. ◘ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE Description Features This series of 3 Stage chargers have 3 specific settings for Wet, Cal-Cal, AGM & GEL type battery to ensure fast, complete and safe charging of your battery as required by the manufacturers. Soft Start Bulk Charge an pre-bulk charge for drained out battery. The charger gives 50% of full constant current charge when it detects the battery is over depleted at less than 9V terminal voltage. When battery voltage rises to 11V the charger will resume the normal constant full current Bulk, constant voltage Absorption and Float charge stages. In the Power Supply mode, the charger provides a constant voltage dc power to the external load connected to the battery and at the same time without over charging the battery. This is ideal for caravan and other battery backup applications. The Power Supply Mode output voltage is the selected Float Voltage. The optional temperature sensor adjusts the charging voltages with the changes in ambient temperatures of the battery. This effectively prevents over and under charging the battery in hot summer days to cold wintry nights. Only the 10Amp SBC-2110 model has convection cooling and one charging bank, others have thermal control fan cooling (zero to full speed) and dual charging banks. The Over Voltage protection, in the case of component failure causing uncontrolled high voltage at the output, the charger will limit the voltage less than 17.5V to prevent damage to the battery and connected load. • 3 Stage (IUoU) switching mode lead acid battery charger • 3 Battery Type (Wet/ Cal-Cal/ AGM & GEL) selections • 3 Float Voltage Settings (13.2/13.5/13.8V) selections • Battery can be connected to charger permanently • Power Supply/Charger Mode selection The power supply mode is ideal to charge battery with load and keeps battery fully charged • Automatic Soft Start Bulk Charge to ensure a safe and gentle initial charging for deeply drained battery • Temperature compensation with optional remote sensor to prevent over and under charging battery at high and low ambient battery ambient temperature. • Dual LED indicators for Bulk, Absorption, Float charge stage ; Fault, Power/Charger Mode and Power On. • Power On-Off Switch • Silent fan cool operation -- The thermal control cooling fan with variable speed moves when ambient temperature of charger exceeds 40°C. • Protections to the charger Short circuit, Over Load, Over temperature • Reversed Polarity (thermal fused) • Protection to the battery and load OVP The charger will keep output voltage less than 17.5V to prevent damage to the battery and load.
2
Embed
LEAD ACID BATTERY CHARGER anson LEAD ACID BATTERY CHARGER ... · PDF fileLEAD ACID BATTERY CHARGER SBC ... This is a simple to use intelligent battery charger with the latest PWM ...
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
LEAD ACID BATTERY CHARGERSBC - 2110 / 2115 / 212012V 3-Stage IUoU Battery Charger with Power Supply Mode Selection
ansonMLEAD ACID BATTERY CHARGERSBC - 826824V 2.2A Smart Battery Chargerusing Micro Processor control unit with pulse width modulation charge technology
ansonM
◘ All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa.◘ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
Description Features
This series of 3 Stage chargers have 3 specific settings for Wet, Cal-Cal, AGM & GEL type battery to ensure fast, complete and safe charging of your battery as required by the manufacturers.
Soft Start Bulk Charge an pre-bulk charge for drained out battery.
The charger gives 50% of full constant current charge when it detects the battery is over depleted at less than 9V terminal voltage. When battery voltage rises to 11V the charger will resume the normal constant full current Bulk, constant voltage Absorption and Float charge stages.
In the Power Supply mode, the charger provides a constant voltage dc power to the external load connected to the battery and at the same time without over charging the battery. This is ideal for caravan and other battery backup applications. The Power Supply Mode output voltage is the selected Float Voltage.
The optional temperature sensor adjusts the charging voltages with the changes in ambient temperatures of the battery. This effectively prevents over and under charging the battery in hot summer days to cold wintry nights.
Only the 10Amp SBC-2110 model has convection cooling and one charging bank, others have thermal control fan cooling (zero to full speed) and dual charging banks.
The Over Voltage protection, in the case of component failure causing uncontrolled high voltage at the output, the charger will limit the voltage less than 17.5V to prevent damage to the battery and connected load.
• 3 Stage (IUoU) switching mode lead acid battery charger
• 3 Battery Type (Wet/ Cal-Cal/ AGM & GEL) selections
• 3 Float Voltage Settings (13.2/13.5/13.8V) selections
• Battery can be connected to charger permanently
• Power Supply/Charger Mode selectionThe power supply mode is ideal to charge battery with load and keeps battery fully charged
• Automatic Soft Start Bulk Charge to ensure a safe and gentle initial charging for deeply drained battery
• Temperature compensation with optional remote sensor to prevent over and under charging battery at high and low ambient battery ambient temperature.
• Dual LED indicators for Bulk, Absorption, Float charge stage ; Fault, Power/Charger Mode and Power On.
• Power On-Off Switch
• Silent fan cool operation -- The thermal control cooling fan with variable speed moves when ambient temperature of charger exceeds 40°C.
• Protections to the charger Short circuit, Over Load, Over temperature
• Reversed Polarity (thermal fused)
• Protection to the battery and load OVPThe charger will keep output voltage less than 17.5V to prevent damage to the battery and load.
◘ All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa.◘ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
Safety
Operation
Introduction
Specifications
Features
Weight
Dimension (WxHxD)
Bulk Charge Max. Current Level (Current Limit) for All Mode
Vbulk@ for Sealed Lead Acid Mode
Vbulk@ for Wet Mode
Vbulk@ for Calcium-Calcium Mode
Ripple & Noise (peak-peak)
Protection
Construction
Cooling System
Approvals
Optimal Efficiency
Max. Power
Full Load AC Current
AC Frequency Range
No Load AC Current
AC Input Voltage
Model
Approx. 400g
150x60x30 mm
2.2A
28.4V
28.8V
29.6V
200mV
Overload, Short Circuit, Over Temperature,Reverse Polarity, No Spark for battery connected,Short Output ans 40HR Max. Charging Time
Poly-Carbonate Casing, Water Resistant
Natural Convection
CE EN55014, 60335, 61000, 62233,IP55 for body only
≥80%
65W
1.3A@100VAC / 1A@230VAC
50 - 60Hz~
100mA@100VAC / 80mA@230VAC
100-240VAC
SBC - 8268
This is a simple to use intelligent battery charger with the latest PWM charging technology controlled by a powerful Micro-Processor Control Unit.It is suitable for all types of lead acid batteries from 8AH to 60AH.
•
•
•
••
•
•••
Microprocessor Control (MCU) 4 Stage Charging (Repair, Bulk, Absorption, Float) in Pulse Width Modulation PWM method.MCU monitors the battery condition from initial qualifying checks, repair, to absorption to float charges.No worries of over or under charging battery, charger can be connected permanently to battery.Auto pulse repair charge for deeply depleted battery.Suitable for all types of Wet, Gel, AGM lead acid battery from 8 to 60 AH.Thermal control regulates charging current in hot or enclosed conditions.Two swappable leads with clamps and eyelet terminal.Simple 3 selection key with intuitive iconic LED indicators.Universal AC input 100V to 240V
The charger only starts charging when it is connected to a battery. So there is no spark in contact with battery terminals.Reverse Polarity and Short Circuit protections are by electronics with flashing LED and charger will return to normal when the fault is cleared.A total time for Bulk and Absorption charge is limited to 40 hours to avoid over charging and waste of energy. Therefore it is not suitable for application of charging battery connected to external load connected. The charger is splash proof as its casing is sealed by ultra sonic.It is convection cooled and has thermal regulation to lower the charging current until the unit's temperature drops to an acceptable level. In the event of persistent rising temperature the charger will shut down its output at a preset maximum temperature.
The Smart Charger runs its own self-tests when connected to an AC source of (100 to 240V). There are 3 Charge Modes to be selected: Sealed Lead Acid / Wet / Calcium-Calcium charge.
The Smart Charger will scan the battery by injecting short DC pulses. If the battery is found faulty, the LED flashes until the faulty battery is disconnected.
When the battery is found to be chargeable, the battery will go through constant current Bulk Charge, then a Pulse Width Absorption Charge, and finally a Pulse Float Charge. The charger can be connected to battery permanently without over charge.
If the battery is found to be sulphated, the Smart Charger will use special repair charge pulses to de-sulphate the battery until battery becomes ready for normal bulk charge.If after 8 hours of repair charge, the battery still cannot be improved, it is then considered to be non- repairable and the LED will flash until battery is removed.
Checks faulty battery
3 Stage charging with Repair Charging
Repair charging
Accessories:A battery Charger with lead terminalsDetachable leads with crocodile clipsConnecting leads with ring teminals
LEAD ACID BATTERY CHARGERSBC - 816812V 5A Smart Battery Chargerusing Micro Processor control unit with pulse width modulation charge technology
ansonM LEAD ACID BATTERY CHARGERSBC - 2110 / 2115 / 212012V 3-Stage IUoU Battery Charger with Power Supply Mode Selection
ansonM
◘ All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa.◘ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
Safety
Operation
Introduction
Specifications
Weight
Dimension (WxHxD)
Bulk Charge Current Level (Current Limit) for Car / Low Temperature Mode
Bulk Charge Current Level (Current Limit) for Motor Mode
Vbulk@ for Car / Motor Mode
Vbulk@ for Low Temperature Mode
Vfloat High Level
Vfloat Low Level
Ripple & Noise (peak-peak)
Protection
Construction
Cooling System
Approvals
Efficiency
Max. Power
Full Load AC Current
AC Frequency Range
No Load AC Current
AC Input Voltage
Model
Approx. 400g
150x60x30 mm
1.5A
14.4V
14.7V
13.5V
12.5V
<200mV
Overload, Short Circuit, Over Temperature,Reverse Polarity, No Spark for battery connected
Poly-Carbonate Casing, Water Resistant
Natural Convection
CE EN55014, 60335, 61000, 62233,IP55 for body only
5A
≥78%
70W
1.5A@100VAC / 1A@230VAC
50 - 60Hz~
100mA@100VAC / 80mA@230VAC
100-240VAC
SBC - 8168
This is a simple to use intelligent battery charger with the latest PWM charging technology controlled by a powerful Micro-Processor Control Unit.It is suitable for all types of lead acid batteries from 5AH to 120AH.
•
•
•
••
••••
Microprocessor Control (MCU) 4 Stage Charging (Repair, Bulk, Absorption, Float) in Pulse Width Modulation PWM method.MCU monitors the battery condition from initial qualifying checks, repair, or bulk to absorption to float charges.No worries of over or under charging battery, charger can be connected permanently to battery.Auto pulse repair charge for deeply depleted battery.Suitable for all types of Wet, Gel, AGM lead acid battery from 5 to 120 AH.Thermal control regulates charging current in hot or enclosed conditionsTwo swappable leads with clamps and eyelet terminal.Simple 3 selection key with intuitive iconic LED indicators.Universal AC input 100V to 240V
The charger only starts charging when it is connected to a battery. So there is no spark in contact with battery terminals.Reverse Polarity and Short Circuit protections are by electronics with flashing LED and charger will return to normal when the fault is cleared.A total time for Bulk and Absorption charge is limited to 40 hours to avoid over charging and waste of energy. Therefore it is not suitable for application of charging battery connected to external load connected. The charger is splash proof as its casing is sealed by ultra sonic.It is convection cooled and has thermal regulation to lower the charging current until the unit's temperature drops to an acceptable level. In the event of persistent rising temperature the charger will shut down its output at a preset maximum temperature.
The Smart Charger runs its own self-tests when connected to an AC source of (100 to 240V). There are 3 Charge Modes to be selected: Motor Cycle / Car / Cold charge.The cold charge has higher voltage and can be used for either low temperature or calcium content battery.
The Smart Charger will scan the battery by injecting short DC pulses. If the battery is found faulty, the LED flashes until the faulty battery is disconnected.
When the battery is found to be chargeable, the battery will go through constant current Bulk Charge, then a Pulse Width Absorption Charge, and finally a Pulse Float Charge. The charger can be connected to battery permanently without over charge.
If the battery is found to be sulphated, the Smart Charger will use special repair charge pulses to de-sulphate the battery until battery becomes ready for normal bulk charge.If after 8 hours of repair charge, the battery still cannot be improved, it is then considered to be non- repairable and the LED will flash until battery is removed.
Checks faulty battery
3 Stage charging with Repair Charging
Repair charging
Features
Accessories:A battery Charger with lead terminalsDetachable leads with crocodile clipsConnecting leads with ring teminals
◘ All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa.◘ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
Specifications
Remarks
Recommended Battery Capacity Range
Included Accessories (cable, spare fuse)
Optional Accessories (Remote Temperature Sensor)
Weight
Dimension (WxHxD)
Anodized Aluminum Casing with Mounting Flange
Charge Cycle, Protection Indication
Approvals
Separate LED for Bulk, Absorption, Float and Fault Mode
Power ON / OFF LED Indicator
Power ON / OFF Switch
Temperature Sensor Socket
Thermostatically Controlled Variable Speed Fan (0 - full speed)