Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. LCD TV PLASMA TV OWNER’S MANUAL LCD TV MODELS 32LG30 37LG50 37LG30 42LG50 42LG30 47LG50 42LGX 52LG50 47LGX 32LG60 32LG70 37LG60 42LG70 42LG60 47LG70 47LG60 52LG70 52LG60 47LG90 PLASMA TV MODELS 42PG25 50PG25 50PG60 60PG60 50PG70 60PG70 P/NO : SAC30708020 (0809-REV08) www.lgusa.com / www.lg.ca As an ENERGY STAR Partner LG Electronics USA, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA).
152
Embed
LCDTV PLASMA TV OWNER’S MANUALstatic.highspeedbackbone.net/pdf/LG_37LG50_Manual.pdf · LCDTV PLASMA TV OWNER’S MANUAL LCD TV MODELS ... to provide some protection against voltage
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Please read this manual carefully before operatingyour set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
LCD TV PLASMA TVOWNER’S MANUALLCD TV MODELS32LG30 37LG5037LG30 42LG5042LG30 47LG5042LGX 52LG5047LGX32LG60 32LG7037LG60 42LG7042LG60 47LG7047LG60 52LG7052LG60
47LG90
PLASMA TV MODELS42PG2550PG25
50PG6060PG60
50PG7060PG70
P/NO : SAC30708020 (0809-REV08)
www.lgusa.com / www.lg.ca
As an ENERGY STAR PartnerLG Electronics USA, Inc.has determined that thisproduct meets the ENERGYSTAR guidelines for energyefficiency.
ENERGY STAR is a set of power-savingguidelines issued by the U.S.Environmental Protection Agency (EPA).
A
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference toradio or television reception, which can be determinedby turning the equipment off and on, the user isencouraged to try to correct the interference by oneor more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment andreceiver.
- Connect the equipment to an outlet on a circuitdifferent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TVtechnician for help.
Any changes or modifications not expressly approvedby the party responsible for compliance could voidthe user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any waywithout written authorization from LG Electronics.Unauthorized modification could void the user’sauthority to operate this product
The lightning flash with arrowheadsymbol, within an equilateral triangle, isintended to alert the user to the presence
of uninsulated “dangerous voltage” within theproduct’s enclosure that may be of sufficientmagnitude to constitute a risk of electric shock topersons.
The exclamation point within an equilateraltriangle is intended to alert the user to
the presence of important operating andmaintenance (servicing) instructions in the litera-ture accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV systeminstaller’s attention to Article 820-40 of the NationalElectric Code (U.S.A.). The code provides guidelines forproper grounding and, in particular, specifies that thecable ground shall be connected to the grounding systemof the building, as close to the point of the cable entryas practical.
1
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.
Do not install near any heat sources such asradiators, heat registers, stoves, or otherapparatus (including amplifiers)that produceheat.
Do not defeat the safety purpose of the polarizedor grounding-type plug. A polarized plug hastwo blades with one wider than the other. Agrounding type plug has two blades and athird grounding prong, The wide blade or thethird prong are provided for your safety. If theprovided plug does not fit into your outlet,consult an electrician for replacement of theobsolete outlet.
Protect the power cord from being walked onor pinched particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.
Only use attachments/accessories specified bythe manufacturer.
Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or soldwith the apparatus. When a cart is used, usecaution when moving the cart/apparatus com-bination to avoid injury from tip-over.
Unplug this apparatus during lighting stormsor when unused for long periods of time.
Refer all servicing to qualified service personnel.Servicing is required when the apparatus hasbeen damaged in any way, such as power-supply cord or plug is damaged, liquid hasbeen spilled or objects have fallen into theapparatus, the apparatus has been exposed torain or moisture, does not operate normally, orhas been dropped.
1
2
3
4
5
7
8
6
9
10
2
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna duringa thunder or lighting storm.
When mounting a TV on the wall, make surenot to install the TV by the hanging power andsignal cables on the back of the TV.
Do not allow an impact shock or any objects tofall into the product, and do not drop onto thescreen with something.
CAUTION concerning the Power Cord:
It is recommend that appliances be placedupon a dedicated circuit; that is, a singleoutlet circuit which powers only that applianceand has no additional outlets or branchcircuits. Check the specification page of thisowner's manual to be certain.
Do not connect too many appliances to thesame AC power outlet as this could result infire or electric shock.
Do not overload wall outlets. Overloaded walloutlets, loose or damaged wall outlets, extensioncords, frayed power cords, or damaged orcracked wire insulation are dangerous. Any ofthese conditions could result in electric shockor fire. Periodically examine the cord of yourappliance, and if its appearance indicates damageor deterioration, unplug it, discontinue use ofthe appliance, and have the cord replaced withan exact replacement part by an authorizedservicer. Protect the power cord from physicalor mechanical abuse, such as being twisted,kinked, pinched, closed in a door, or walkedupon. Pay particular attention to plugs, walloutlets, and the point where the cord exits theappliance.
Do not make the TV with the power cordplugged in. Do not use a damaged or loosepower cord. Be sure do grasp the plug whenunplugging the power cord. Do not pull on thepower cord to unplug the TV.
WARNING - To reduce the risk of fire or electricalshock, do not expose this product to rain,moisture or other liquids. Do not touch the TVwith wet hands. Do not install this productnear flammable objects such as gasoline orcandles or expose the TV to direct airconditioning.
Do not expose to dripping or splashing and donot place objects filled with liquids, such asvases, cups, etc. on or over the apparatus (e.g.on shelves above the unit).
GGRROOUUNNDDIINNGG
Ensure that you connect the earth ground wireto prevent possible electric shock (i.e. a TVwith a three-prong grounded AC plug must beconnected to a three-prong grounded AC out-let). If grounding methods are not possible,have a qualified electrician install a separatecircuit breaker.
Do not try to ground the unit by connecting itto telephone wires, lightening rods, or gaspipes.
Mains plug is the disconnecting device. Theplug must remain readily operable.
Keep the product away from direct sunlight.
12
11
14
13
16
17
18
19
Power Supply
Short-circuitBreaker
15
3
AANNTTEENNNNAASS
OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg
If an outdoor antenna is installed, follow theprecautions below. An outdoor antenna systemshould not be located in the vicinity of over-head power lines or other electric light orpower circuits, or where it can come in contactwith such power lines or circuits as death orserious injury can occur.
Be sure the antenna system is grounded so asto provide some protection against voltagesurges and built-up static charges.
Section 810 of the National Electrical Code(NEC) in the U.S.A. provides information withrespect to proper grounding of the mast andsupporting structure, grounding of the lead-inwire to an antenna discharge unit, size ofgrounding conductors, location of antenna dis-charge unit, connection to grounding elec-trodes and requirements for the groundingelectrode.
When cleaning, unplug the power cord andscrub gently with a soft cloth to preventscratching. Do not spray water or other liquidsdirectly on the TV as electric shock may occur.Do not clean with chemicals such as alcohol,thinners or benzene.
MMoovviinngg
Make sure the product is turned off,unplugged and all cables have been removed. Itmay take 2 or more people to carry larger TVs.Do not press against or put stress on the frontpanel of the TV.
VVeennttii llaattiioonn
Install your TV where there is proper ventila-tion. Do not install in a confined space such asa bookcase. Do not cover the product withcloth or other materials (e.g.) plastic whileplugged in. Do not install in excessively dustyplaces.
If you smell smoke or other odors coming fromthe TV or hear strange sounds, unplug the powercord contact an authorized service center.
Do not press strongly upon the panel withhand or sharp object such as nail, pencil orpen, or make a scratch on it.
2220
23
24
25
21
Antenna Lead in Wire
Antenna Discharge Unit(NEC Section 810-20)
Grounding Conductor(NEC Section 810-21)
Ground Clamps
Power Service GroundingElectrode System (NECArt 250, Part H)
Manufactured under license from Dolby Laboratories.
“Dolby “and the double-D symbol are trademarks of
Dolby Laboratories.
CALIBRATE LIKE A PRO: Sophisticated and detailed
calibrations can be made through the ISFccc mode.
Detailed calibration requires a licensed technician.
Please contact your local dealer to inquire about an
ISF certified technician.
THX (Thomlinson Holman’s Experiment) is the audio
and video certification standard of THX established
by George Lucas, who directed the movie Star Wars,
and Thomlinson.
This is the product to be certified in THX display area
and guarantees screen quality that exceeds the display
standard specification in both hardware and software.
FOR LCD TV
� If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is
nothing wrong with TV.� Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.� Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce
some temporary distortion effects on the screen.
On Disposal (Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product withgeneral household waste. Disposal of this product must be carried out in accordance to the regulations of your localauthority.
Install the power plug closely.
Use of ferrite core
(This feature is not available for all models.)
Ferrite core can be used to reduce the electromagnetic wavewhen connecting the power cord.The closer the location of the ferrite core to the power plug,the better it is.
� This feature is not available for all models.
PR
EPA
RA
TIO
N
7
PREPARATION
ACCESSORIESEnsure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
Protection CoverScrew for stand fixing(Refer to P.20)
(Only 32LG30/70,
37LG30/50, 42LG30/50)
x 4 x 4
32/37/42/47/52LG60, 42/47LGX
Protection Cover Cable ManagementClip
2EA 4EA 1EA 4EA 32LG60: 3EA37LG60: 4EA
Bolts for stand assembly(Refer to P.14)
(Only 32/37LG60) (Only 42LG60, 42LGX)
Cable Management Clip
ProtectionCover
Ferrite core(Refer to P.6)
(This feature is not availablefor all models.)
(Only 50PG25,50/60PG60,50/60PG70)
(Only 42PG25)
or
or
Cable Holder
Bolts for standassembly
(Refer to P.13)
x 4
PR
EPA
RA
TIO
N
8
FRONT PANEL INFORMATION
PREPARATION
� Image shown may differ from your TV.
� NOTE: If your TV has a protection tape attached, remove the tape.And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).
Plasma TV Models
CHVOLMENUINPUT ENTER
CHVOLMENUINPUT ENTER
INPUTButton
MENUButton
ENTERButton
VOLUME
(-, +) Buttons
CHANNEL
(EE,DD)ButtonsCHVOLMENUINPUT ENTER
Remote Control Sensor
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.Illuminates blue when the TV is switched on.
LCD TV Models
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using PPoowweerr IInnddiiccaattoorr inthe OPTION menu. GG pp..8855)
CH
VOL
MENU
INPUT
ENTER
CHANNEL ( , )
Buttons
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
Intelligent Sensor
Adjusts picture according to the surroundingconditions
32/42/47/52LG70, 47LG90
Remote Control Sensor
PR
EPA
RA
TIO
N
9
LCD TV Models
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using PPoowweerr IInnddiiccaattoorr inthe OPTION menu. GG pp..8855)
CH
VOL
MENU
INPUT
ENTER
CHANNEL ( , )
Buttons
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
Intelligent Sensor
Adjusts picture according to thesurrounding conditions.
Intelligent Sensor (Except 32/37/42LG30)
Adjusts picture according to the surroundingconditions
ENTER
CH
VOL
MENU
INPUT
CHANNEL ( , )
Buttons
VOLUME (+, -)
Buttons
ENTER Button
MENU Button
INPUT Button
32/37/42LG30, 37/42/47/52LG50
32/37/42/47/52LG60, 42/47LGX
POWER Button
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates white when the set is switched on.
(Can be adjusted using PPoowweerr IInnddiiccaattoorr inthe OPTION menu. GG pp..8855)
Remote Control Sensor
PR
EPA
RA
TIO
N
10
BACK PANEL INFORMATION
PREPARATION
Plasma TV Models
� Image shown may differ from your TV.
R
( )
12
AV IN 2
L/M
ONO
RA
UD
IOVI
DEO
USB
INH
DM
I IN
4
( )
9
10
1
R
RGB IN
COMPONENT IN
AUDIO(RGB/DVI)
RGB(PC)
ANTENNA/CABLE IN
1
2
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO VIDEO
AUDIO OUT
OPTICAL COAXIAL
MONO( )
AUDIO
S-VI
DEO
DIGITAL AUDIO OUT
AV
IN 1
HDMI/DVI IN
3
2
1
REMOTECONTROL IN
1
3
4
6
7
8
2
9
5
HDMI/DVI IN, HDMI IN
Digital Connection. Supports HD video and Digital audio. Doesn’tsupport 480i. Accepts DVI video using an adapter or HDMI toDVI cable (not included).
COMPONENT IN
Analog Connection. Supports HD. Uses a red, green, and blue cable for video & redand white for audio.
RGB (PC)
Analog PC Connection. Uses a D-sub 15 pin cable(VGA cable).AUDIO (RGB/DVI)
1/8” headphone jack for analog PC audio input.
REMOTE CONTROL IN PORT
For a wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.Connect cable signals to this jack.
DIGITAL AUDIO OUT
Digital audio output for use with amps and hometheater systems. Includes an optical and/or coaxial connection.Note: In standby mode, these ports do not work.
AUDIO OUT
Analog audio output for use with amps and hometheater systems.
AV (Audio/Video) IN
Analog composite connection. Supports standarddefinition video only (480i).S-VIDEO
Better quality than standard composition.Supports standard definition video only (480i).
USB INPUT
Used for viewing photos and listening to MP3s.
USB SERVICE ONLY or RS-232C IN (SERVICEONLY)
Used for software updates.
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DCpower.
1
2
3
4
5
6
9
10
11
12
7
8
PR
EPA
RA
TIO
N
11
LCD TV Models
AV IN 2
L/M
ONO
RA
UD
IOVI
DEO
HD
MI I
N 3
USB
IN
( )
RGB IN
COMPONENT IN
AUDIO(RGB/DVI)
RGB(PC) REMOTECONTROL IN
ANTENNA/CABLE IN
1
2
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO
OPTICAL COAXIAL
DIGITAL AUDIO OUT
AUDIO OUT
AV
IN 1
R
HDMI/DVI IN
2
1VIDEO MONO( ) AUDIOS-VIDEO
1
34
6
7
8
2
9
9
5
RGB IN
COMPONENT IN
AUDIO(RGB/DVI)
RGB(PC) REMOTECONTROL IN
ANTENNA/CABLE IN
1
2
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO
DIGITALAUDIO OUT
OPTICAL
AUDIO OUTA
V IN
1R
VIDEO MONO( ) AUDIOS-VIDEO
2
1
HDMI/DVI IN
1
34
6
7
8
2
9
5
10
1
AV IN 2L/
MON
OR
AU
DIO
VID
EOU
SBSE
RVICE
ONLY
HD
MI I
N 3
( )
9
11
1
37/42/47/52LG50, 32LG70
32/37/42LG30
R
( )
12
PR
EPA
RA
TIO
N
12
PREPARATION
R
AV IN 2
L/M
ONO
RA
UD
IOVI
DEO
HD
MI I
N 4
USB
IN
( )
9
10
1
� Image shown may differ from your TV.
32/37/42/47/52LG60, 42/47LGX
42/47/52LG70, 47LG90
LCD TV Models
R
( )
12
12
RGB IN
COMPONENT IN
AUDIO(RGB/DVI)
RGB(PC) REMOTECONTROL IN
ANTENNA/CABLE IN
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO
OPTICAL COAXIAL
DIGITAL AUDIO OUT
AUDIO OUT
AV
IN 1
R
HDMI/DVI IN
2
3
1
VIDEO MONO( ) AUDIOS-VIDEO
2
1
1 34
6
7
8
2
9
5
AV IN
L/M
ONO
RA
UD
IOVI
DEO
HD
MI I
N 4
USB
IN
9
10
1
(RGB/DVI)
AUDIO
RGB(PC)
REMOTECONTROL IN
RS-232C IN(SERVICE ONLY)
OPTICAL
COAXIAL
DIGITAL AUDIO OUT
R
1 2 3
CO
MP
ON
EN
T IN
21V
IDE
OA
UD
IO
HD
MI/D
VI I
N
RG
B IN
ANTENNA/CABLE IN
2
7
4
1
3
6
11
PR
EPA
RA
TIO
N
13
STAND INSTRUCTION� Image shown may differ from your TV.
Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in theback of the TV.
1
2
3
INSTALLATION (Only 42PG25)
Plasma TV models
DETACHMENT
Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.
1
Loose the bolts from TV.2
42PG25 50PG25/60/70 60PG60/70
Detach the stand from TV.3
After removing the stand, install the includedpprrootteeccttiioonn ccoovveerr over the hole for the stand.
Press the PPRROOTTEECCTTIIOONN CCOOVVEERR into the TVuntil you hear it click.
PROTECTION COVER
GG When assembling the desk type stand, make surethe bolt is fully tightened (If not tightened fully,the TV can tilt forward after the product installa-tion). Do not over tighten.
NOTE!
PR
EPA
RA
TIO
N
14
PREPARATION
32/37/42/47/52LG60, 42/47LGX
Assemble the parts of the SSTTAANNDD BBOODDYY
with CCOOVVEERR BBAASSEE of the TV.2
Assemble the TV as shown.3
Fix the 4 bolts securely using the holes in theback of the TV.
4
Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.
1
32LG60 37LG60 42LG60, 42LGX
SSTTAANNDD BBOODDYY SSTTAANNDD BBOODDYY
CCOOVVEERR BBAASSEE
SSTTAANNDD BBOODDYY
CCOOVVEERR BBAASSEECCOOVVEERR BBAASSEE
INSTALLATION (Only 32/37/42LG60, 42LGX)
� Image shown may differ from your TV.
GG When assembling the desk type stand, make sure thebolt is fully tightened (If not tightened fully, the TVcan tilt forward after the product installation). Do notover tighten.
NOTE!
PR
EPA
RA
TIO
N
15
DETACHMENT
Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.
1
Loose the bolts from TV.2
Detach the stand from TV.3
After removing the stand, install the included pprroo--tteeccttiioonn ccoovveerr over the hole for the stand.
After removing the protection paper from theprotection cover, adhere it to the TV as shown.
Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.
1
Loose the bolts from TV.2
Detach the stand from TV.3
After removing the stand, install the includedpprrootteeccttiioonn ccoovveerr over the hole for the stand.
Press the PPRROOTTEECCTTIIOONN CCOOVVEERR into the TVuntil you hear it click.
PROTECTION COVER
GG When assembling the desk type stand, make surethe bolt is fully tightened (If not tightened fully,the TV can tilt forward after the product installa-tion). Do not over tighten.
NOTE!
PR
EPA
RA
TIO
N
17
VESA WALL MOUNTINGInstall your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, pleasecontact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
GG Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electricshock.
CAUTION
GG Screw length needed depends on the wall mountused. For further information, refer to the instruc-tions included with the mount.
GG Standard dimensions for wall mount kits are shownin the table.
GG When purchasing our wall mount kit, a detailedinstallation manual and all parts necessary forassembly are provided.
GG Do not use screws longer then the standard dimen-sion, as they may cause damage to the inside tothe TV.
GG For wall mounts that do not comply with the VESA
standard screw specifications, the length of thescrews may differ depending on their specifica-tions.
GG Do not use screws that do not comply with theVESA standard screw specifications.Do not use fasten the screws too strongly, this maydamage the TV or cause the TV to a fall, leading topersonal injury. LG is not liable for these kinds ofaccidents.
GG LG is not liable for TV damage or personal injurywhen a non-VESA or non specified wall mount isused or the consumer fails to follow the TV installa-tion instructions.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
� Image shown may differ from your TV.
4 inches
4 inches
4 inches4 inches
SWIVEL STANDAfter installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suityour viewing position.
GG Ensure adequate ventilation by following the clearance recommendations.
GG Do not mount near or above any type of heat source.CAUTION
ATTACHING THE TV TO A DESK (Only 32LG30/70, 37LG30/50, 42LG30/50)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causinginjury or damaging the product.
GG To prevent TV from falling over, the TV should be securely attached to the floor/wall per installationinstructions. Tipping, shaking, or rocking the machine may cause injury.
WARNING
1-Screw(provided as parts of the product)
Desk
Stand
PR
EPA
RA
TIO
N
21
SECURING THE TV TO THE WALL TO PREVENT FALLINGWHEN THE TV IS USED ON A STAND
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
� Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that ismounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
� Use a sturdy rope (sold separately) to tie the product. It is safer to tiethe rope so it becomes horizontal between the wall and the product.
� You should purchase necessary components to prevent TV from falling off of the stand.� Image shown may differ from your TV.
GG Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
GG To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
NOTE!
PR
EPA
RA
TIO
N
22
ANTENNA OR CABLE CONNECTION
PREPARATION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable BoxConnection.
For optimum picture quality, adjust the antenna direction if needed.
2. Cable
WallAntennaSocket
OutdoorAntenna(VHF, UHF)
Cable TVWall Jack
Multi-family Dwellings/Apartments(Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wirewhen connecting the antenna.
Copper Wire
� To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. � If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.� If the antenna is not installed properly, contact your dealer for assistance.
ANTENNA/CABLE IN
( )
R
ANTENNA/CABLE IN
( )
R
� To prevent damage do not connect to the power outlet until all connections are made between the devices.
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
23
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUPThis TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
1. How to connect
Connect the video outputs (Y, PB, PR) of the digital set-top box to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11 jacks onthe TV. Match the jack colors (Y = green, PB = blue, andPR = red).
Connect the audio output of the digital set-top box to
the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11 jacks on the TV.2
1
2. How to use� Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box. operation)
� Select the CCoommppoonneenntt 11 input source on the TV usingthe IINNPPUUTT button on the remote control.
� If connected to CCOOMMPPOONNEENNTT IINN22 input, select theCCoommppoonneenntt 22 input source on the TV.
� To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)
1. How to connect
2. How to use
� Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)
� Select the AAVV11 input source on the TV using the IINNPPUUTT
button on the remote control.
� If connected to AAVV IINN22, select AAVV22 input source on the TV.
1
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
35
GG Do not connect to both Video and S-Video at the sametime. In the event that you connect both Video and theS-Video cables, only the S-Video will work.
CAUTION
GG S-Video provides better quality than composite. Use itwhen available.
GG 32/37/42LG30, 42/50PG25: To get the the bestpicture quality, adjust the PC graphics card to1360x768.
GG 37/42/47/52LG50, 32/37/42/47/52LG60,32/42/47/52LG70, 42/47LGX, 47LG90,50/60PG60, 50/60PG70: To get the the bestpicture quality, adjust the PC graphics card to1920x1080.
GG Depending on the graphics card, DOS mode maynot work if a HDMI to DVI Cable is in use.
GG In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or bright-ness. If noise is present, change the PC output toanother resolution, change the refresh rate toanother rate or adjust the brightness and contraston the PICTURE menu until the picture is clear.
GG Avoid keeping a fixed image on the screen for along period of time. The fixed image could becomepermanently imprinted on the screen.
GG The synchronization input form for Horizontal andVertical frequencies is separate.
NOTES!
DVI to HDMI Connection
32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV
- Connect the DVI output of the PC to the HHDDMMII//DDVVII IINN 11, 22, or 33 jack on the TV.
For 32/37/42LG30 For 37/42/47/52LG50, 32/37/42/47/52LG60,
32/42/47/52LG70, 42/47LGX, 47LG90
* Only RGB-PC mode
GG Depending on the graphics card, some resolution settings may not allow the image to be positioned on thescreen properly.
GG If there are overscan in HDMI-PC 1920x1080, change aspect ratio to JJuusstt ssccaann.
NOTE!
Resolution
720x400
1360x768
640x350
640x480
800x600
1024x768
1280x1024
1600x1200
1920x1080RGB-PC
1920x1080HDMI-PC
1280x768
Horizontal Vertical Frequency(KHz) Frequency(Hz)
31.468 70.09
31.469 70.08
31.469 59.9437.500 75.0037.861 72.80
35.156 56.2537.879 60.3146.875 75.0048.077 72.18
48.363 60.0056.476 70.0660.023 75.02
47.776 59.8760.289 74.893
63.981 60.0279.976 75.025
47.712 60.015
75.00 60.00
66.587 59.934
67.5 60.00
* Only RGB-PC mode
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
41
Resolution
720x400
1360x768
640x350
640x480
800x600
1024x768
1280x1024
1600x1200
1920x1080
1280x768
Horizontal Vertical Frequency(KHz) Frequency(Hz)
31.468 70.09
31.469 70.08
31.469 59.9437.500 75.0037.861 72.80
35.156 56.2537.879 60.3146.875 75.0048.077 72.18
48.363 60.0056.476 70.0660.023 75.02
47.776 59.8760.289 74.893
63.981 60.0279.976 75.025
47.712 60.015
75.00 60.00
66.587 59.934
For 42/50PG25, 50/60PG60, 50/60PG70
* Only RGB-PC mode
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
42
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
You can choose the resolution in RGB-PC mode.
The PPoossiittiioonn, PPhhaassee, and SSiizzee can also be adjusted.
Select PPIICCTTUURREE.
Select SSccrreeeenn ((RRGGBB--PPCC)).
Select RReessoolluuttiioonn.
Select the desired resolution.
1024 x 768
1280 x 768
1360 x 768
1366 x 768
Auto config.
Resolution G
Position
Size
Phase
Reset
SCREEN Move Prev.MENU
1MENU
3
4
2ENTER
ENTER
ENTER
5ENTER
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R GOnly for
32/37/42LG30
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
43
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.
Select SSccrreeeenn ((RRGGBB--PPCC)).
Select AAuuttoo ccoonnff iigg...
Auto config. G
Resolution
Position
Size
Phase
Reset
SCREEN Move Prev.MENU
To Set
3
2ENTER
ENTER
Select YYeess.4
ENTER
Start Auto Configuration.5
ENTER
Select PPIICCTTUURREE.1
MENU
• If the position of the image is still notcorrect, try Auto adjustment again.
• If picture needs to be adjusted againafter Auto adjustment in RGB-PC, youcan adjust the PPooss ii tt ii oonn, SS ii zzee orPPhhaassee.
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R G
Yes No
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
44
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Position, Size, and Phase
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.
This feature operates only in RGB-PC mode.
Select PPoossiitt iioonn, SSii zzee, or PPhhaassee.
Make appropriate adjustments.
Auto config.
Resolution
Position G
Size
Phase
Reset
GF
D
E
SCREEN Move Prev.MENU
3ENTER
4ENTER
� PPoossiitt iioonn: This function is to adjust pic-ture to left/right and up/down as youprefer.
� SSiizzee: This function is to minimize anyvertical bars or stripes visible on thescreen background. And the horizontalscreen size will also change.
� PPhhaassee: This function allows you toremove any horizontal noise and clear orsharpen the image of characters.
Select PPIICCTTUURREE.
Select SSccrreeeenn ((RRGGBB--PPCC)).
1MENU
2ENTER
5ENTER
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R G
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
45
Screen Reset (Reset to original factory values)
Returns PPoossiitt iioonn, SSiizzee, and PPhhaassee to the default factory settings.
This feature operates only in RGB-PC mode.
Auto config.
Position
Resolution
Size
Phase
Reset G
SCREEN Move Prev.MENU
To Set
Select RReesseett.3
ENTER
Select PPIICCTTUURREE.
Select SSccrreeeenn ((RRGGBB--PPCC)).
1MENU
2ENTER
Select YYeess.4
ENTER
5ENTER
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R G
Yes No
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
46
USB CONNECTION (Except 32/37/42LG30)
EXTERNAL EQUIPMENT SETUP
AV IN 2
L/M
ONO
RA
UD
IOVI
DEO
HD
MI I
N 3
USB
IN
Connect the USB device to the UUSSBB II NN jack on the sideof TV.
1. How to connect
1
2. How to use
� After connecting the UUSSBB II NN jack, you use the USB func-
tion. (GG pp..6644)
1or
i.e)
EX
TE
RN
AL E
QU
IPM
EN
T S
ET
UP
47
AUDIO OUT CONNECTION
Send the TV’s audio to external audio equipment via the Audio Output port.
RS-232C IN(CONTROL & SERVICE)
R
AUDIO
AUDIO OUT
AV
IN 1
VIDEO L R(MONO) AUDIOS-VIDEO
L RAUDIO
1
N
UDIOB/DVI)
REMOTECONTROL IN
ANTENNA/CABLE IN
RS-232C IN(CONTROL & SERVICE)
L R
AUDIO
OPTICAL COAXIAL
DIGITAL AUDIO OUT
AUDIO OUT
AV
IN 1
VIDEO L R(MONO) AUDIOS-VIDEO
1
2GG When connecting with external audio equipments, such as
amplifiers or speakers, you can turn the TV speakers off inthe menu. (GG pp..9933)
NOTE!
G Do not look into the optical output port. Looking at thelaser beam may damage your vision.
GG Block the SPDIF out (optical/coaxial) about the contentswith ACP(Audio Copy Protection) function.
CAUTION
Connect one end of the optical or coaxial cable to theTV’s OOPPTTIICCAALL or CCOOAAXXIIAALL (Except 32/37/42LG30)port of DDIIGGIITTAALL AAUUDDIIOO OOUUTT.
Connect the other end of the optical or coaxial cable tothe digital audio input on the audio equipment.
Set the “TV Speaker option - Off” in the AUDIO menu. (GGpp..9933). See the external audio equipment instruction manu-al for operation.
1. How to connect
2
3
1
Connect audio outputs to the TV’s AAUUDDIIOO OOUUTT jacks.
Set the “TV Speaker option - Off” in the AUDIO menu.(GG pp..9933). See the external audio equipment instructionmanual for operation.
1. How to connect
2
1
Analog (Except 32/37/42/47/52LG60, 42/47LGX)
Digital
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
48
REMOTE CONTROL FUNCTIONS
WATCHING TV / CHANNEL CONTROL
When using the remote control, aim it at the remote control sensor on the TV.
INPUT
FAV
MUTE
TV
STB
POWER
Q. MENU MENU
AV MODERETURN
ENTER
VOL CH
1 2 3
4 5 6
7 8
0
9
FLASHBK
PAGE
DVD
VCR
TV/STB/DVD/VCR
POWER
Q.MENU
MENU
INPUT
VOLUME UP/DOWN
FAV
MUTE
CHANNELUP/DOWN
PAGEUP/DOWN
— (DASH)
FLASHBK
Select the remote operating mode: TV, STB, DVD, or VCR.
Turns your TV or any other programmed equipment on oroff, depending on the mode.
Select the desired quick menu source. GG pp..5511
Displays the main menu.
Clear all on-screen displays and return to TV viewing fromany menu.
External input modes rotate in regular sequence.
Increase/decrease the sound level.
Scroll through the programmed Favorite channels. GG pp..5511
Switch the sound on or off. GG pp..5500
Select available channels.
Move from one full set of screen information to the next one.
Used to enter a program number for multiple
program channels such as 2-1, 2-2, etc.
Tune to the last channel viewed.
Control video cassette recorders or DVD players.
Control USB menu (PHOTO LIST and MUSIC LIST.)
Control the SIMPLINK compatible devices.
NUMBER button
VCR/DVD, USB,SIMPLINK
Control buttons
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
49
Installing Batteries
� Open the battery compartment cover on the back side and installthe batteries matching correct polarity (+with +,-with -).
� Install two 1.5V AAA batteries. Don’t mix old or used batteries withnew ones.
� Close cover.
THUMBSTICK(Up/Down/Left
Right/ENTER)
RETURN
SIMPLINK
AV MODE
Navigate the on-screen menus and adjust the system settings to your preference.
Allows the user to move return one step in an interactive application or other user interactionfunction.
See a list of AV devices connected to TV.
When you toggle this button, the SIMPLINK menu appears at the screen. GG pp..6622--6633
It helps you select and set images and sounds. GG pp..6611
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
50
TURNING ON THE TV
WATCHING TV / CHANNEL CONTROL
NOTE!
GG If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
� In standby mode to turn TV on, press the , IINNPPUUTT, CCHH ((DDEE or ))
button on the TV or press the PPOOWWEERR, IINNPPUUTT, CCHH(( or )), NNuummbbeerr((00~99)) button on the remote control.
Select the viewing source by using the IINNPPUUTT button on the remote control.
� This TV is programmed to remember which power state it was last set to,even if the power cord is out.
When finished using the TV, press the PPOOWWEERR button on the remote control.The TV reverts to standby mode.
1
2
3
Press the CCHH (( or )) or NNUUMMBBEERR buttons to select a channel number.1
VOLUME ADJUSTMENT
CHANNEL SELECTION
Press the VVOOLL ((++ or --)) button to adjust the volume.
If you want to switch the sound off, press the MMUUTTEE button.
You can cancel the Mute function by pressing the MMUUTTEE or VVOOLL ((++ or --))
button.
Adjust the volume to suit your personal preference.
1
2
3
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
51
QUICK MENU
Display each menu.
Make appropriate adjustments.
� AAssppeecctt RRaattiioo: Selects your desired picture format.
� PPoowweerr SSaavviinngg (Plasma TV Only): Adjusts screenbrightness to reduce the power consumption of theTV.
� BBaacckkll iigghhtt (LCD TV Only): Adjust the brightnessof LCD panel to control the brightness of the screen.
� CClleeaarr VVooiiccee: By differentiating the human soundrange from others, it helps make human voicessound better.
� PPiiccttuurree MMooddee: Selects the factory preset picturedepend on the viewing environment.
� SSoouunndd MMooddee: Selects the factory preset sound fortype of program.
� CCaappttiioonn: Select on or off.
� MMuullttii AAuuddiioo: Changes the audio language (Digitalsignal).
SSAAPP: Selects MTS sound (Analog signal).
� SSlleeeepp TTiimmeerr: Select the amount of time beforeyour TV turns off automatically.
� DDeell//AAdddd//FFaavv: Select channel you want to add/deleteor add the channel to the Favorite List.
� UUSSBB EEjjeecctt: Select “USB Eject” in order to ejectUSB device.
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
1Q. MENU
2
LCD TV
Q.Menu
3
FF 16:9 GG
Vivid
Off
Standard
Off
English
Off
Add
Eject
Aspect Ratio
Backlight
Clear Voice
Picture Mode
Sound Mode
Caption
Multi Audio
Sleep Timer
Del/Add/Fav
USB Eject
CH
Plasma TV
Q.Menu
Close Close
3
FF 16:9 GG
Vivid
Off
Standard
Off
English
Off
Add
Eject
Aspect Ratio
Power Saving
Clear Voice
Picture Mode
Sound Mode
Caption
Multi Audio
Sleep Timer
Del/Add/Fav
USB Eject
CH
3Q. MENU
Return to TV viewing.
Except 32/37/42LG30
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
52
INITIAL SETTING
WATCHING TV / CHANNEL CONTROL
This Function guides the user to easily set the essential items for viewing the TV for the first time when pur-
chasing the TV. If will be displayed on the screen when turning the TV on for the first time. It can also be acti-
vated from the user menus.
Select HHoommee Mode.1
2ENTER
Select AAuuttoo or MMaannuuaall.
Select desired time option.
1
3ENTER
2Year
Current Time Setting
2007
Month 11
Date 15
Hour 5 PM
Minute 52
Time Zone Eastern
Daylight Saving Off
FF Auto GG
ExitEnter RETURN
Step2. Time Setting
Selecting the environment.Choose the setting mode you want.
In Store Home
ExitEnter RETURN
Step1. Mode Setting
Step1. Mode setting
Step2. Time setting
� Default selection is “HHoommee”. We recommend setting the TV to “HHoommee” mode for the best picture in yourhome environment.
� “IInn--ssttoorree” Mode is only intended for use in retail environments. Customers can adjust the “PPiiccttuurree menu -PPiiccttuurree mmooddee” manually while inspecting the TV, but the TV will automatically return to preset in-storemode after 5 minutes.
� “IInn--ssttoorree” Mode is an optimal setting for displaying at stores. “In-Store” mode initializes the TV to set theimage quality and operates “TTrruuMMoottiioonn DDeemmoo (For 37/42/47/52LG60, 42/47/52LG70, 42/47LGX)” or“LLooccaall DDiimmmmiinngg DDeemmoo (For 47LG90)” after a certain period of time.
Only these input signals which are connected to a TV can be activated and selected.
Select the desired input source.
� You can also select the desired input source in the IINNPPUUTT menu(Except 32/37/42LG30).
1INPUT
Antenna Cable AV1 AV2 Component1
HDMI3 HDMI2 HDMI1 RGB-PC
Component2
Antenna Cable AV1 AV2 Component1
ENTER
� AAnntteennnnaa: Select it to watch over-the-air broadcasts.
� CCaabbllee: Select it to watch cable and digital cable.
� AA VV: Select them to watch a VCR or other external equipment.
� CCoommppoonneenntt: Select them to watch DVD or a Digital set-top box.
� RRGGBB--PPCC: Select it to view PC input.
� HHDDMMII: Select them to watch high definition devices.
Antenna Cable AV1 AV2 Component1
Input LabelQ.MENU ExitRETURN
Select a desired input source (exceptAAnntteennnnaa or CCaabbllee). Then, you can selectyour desired Input Label with using Q. MENUbutton. GG pp..6600
Disconnected inputs are inactive (grayed out)ie)
32/37/42LG30, 37/42/47/52LG50, 32LG70
Antenna Cable AV1 AV2 Component1
HDMI4 HDMI3 HDMI2 HDMI1 RGB-PC
Component2
Plasma TV, 42/47/52LG70, 47LG90
Antenna Cable AV Component1
HDMI4 HDMI3 HDMI2 HDMI1 RGB-PC
Component2
32/37/42/47/52LG60, 42/47LGX
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
60
INPUT LABEL
WATCHING TV / CHANNEL CONTROL
You can set a label for each input source when it's not in use.
EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1EE
Select OOPPTTIIOONN.
Select IInnppuutt LLaabbeell.
Select the label.
1MENU
2ENTER
Select the source.3
ENTER
4
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
With using OPTION menu
Select the source.
Select the label.
1INPUT
2Q. MENU
3RETURN
Return to the previous menu.
MENUReturn to TV viewing.
With using INPUT button
� When new external device is connected, this popup menu is displayed automatically.
If selecting YYeess, you can select input source that you want to appreciate.
� But, when selecting “SSIIMMPPLLIINNKK - OO nn”, popup menu for HDMI input will not be displayed.
NoYes
!New external device is connected.Do you want to enjoy this?
! Select input source that you want to appreciate.
AV1
AV2
Component1
AV1 FF GG
AV2
Component1
HDMI1
RGB-PC
Component2
HDMI2
HDMI3
Close
AV1 FF GG
AV2
Component1
HDMI1
RGB-PC
Component2
HDMI2
HDMI3
HDMI4
Close
FF GGAV
Component1
HDMI1
RGB-PC
Component2
HDMI2
HDMI3
HDMI4
Close
Plasma TV, 42/47/52LG70,47LG90
32/37/42/47/52LG60,
42/47LGX
32/37/42LG30,37/42/47/52LG50,32LG70
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
61
AV MODE
You can select the optimal images and sounds.
1AV MODE
2
Off Cinema
Game Sport
Off Cinema
Game Sport
Press the AAVV MMOODDEE button repeatedly to select the desired source.
ENTER
� If you select “CCiinneemmaa // CCiinneemmaa”in AV mode, CCiinneemmaa will be selectedboth for “PICTURE menu - PictureMode” and “AUDIO menu - SoundMode” respectively.
� If you select “OOff ff” in AV mode, the“PPiiccttuurree MMooddee” and “SSoouunndd MMooddee”return to previous selected value.
All models (Except 50/60PG60, 50/60PG70)
Only for 50/60PG60, 50/60PG70
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
62
WATCHING TV / CHANNEL CONTROL
This function operates only with devices with the logo.
The TV might not function properly when using it with other products with HDMI-CEC function.
This allows you to control and play other AV devices connected with HDMI cable without additional cables and
settings.
To start using SIMPLINK, turn it on in the user menus.
EnterMoveOPTION
Select OOPPTTIIOONN.
Select SSIIMMPPLLIINNKK.
Select OOnn or OOff ff.
EnterMoveOPTION
E
1MENU
3
2ENTER
ENTER
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Off
On
NOTE!
GG Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of theSIMPLINK device with the HDMI cable.
GG When you switch the Input source with the INPUT button on the remote control, the SIMPLINK devicewill stop.
GG When you select a device with home theater functionality, the sound output automatically switches tothe home theater speakers.
GG If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITALAUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIM-PLINK device with an OPTICAL cable.
E
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
WA
TC
HIN
G T
V / C
HA
NN
EL C
ON
TR
OL
63
� DDiirreecctt PPllaayy:: After connecting AV devices to the TV, you can directly control the devices and play media with-out additional settings.
� SSeelleecctt AAVV ddeevviiccee:: Enables you to select one of the AV devices connected to TV.
� DDiisscc ppllaayybbaacckk:: Control connected AV devices by pressing the , ENTER, G, A, ll ll, FF and GG buttons.
� PPoowweerr ooffff aallll ddeevviicceess:: When you power off the TV, all connected devices are turned off.
� SSwwiittcchh aauuddiioo--oouutt:: Offers an easy way to switch audio-out.
� SSyynncc PPoowweerr oonn:: When you play the connected AV device, TV will automatically turn on.
(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not providethis function)
Note: To operate SIMPLINK, an HDMI cable over Version 1.2 with *CEC function should be used. (*CEC: ConsumerElectronics Control).
SIMPLINK Menu
TTVV vviieewwiinngg: Switch to the previous TVchannel regardless of the current mode.
DDIISSCC ppllaayybbaacckk: Select and play discs.When multiple discs are available, the titlesof discs are conveniently displayed at thebottom of the screen.
VVCCRR ppllaayybbaacckk: Control the connectedVCR.
HHDDDD RReeccoorrddiinnggss ppllaayybbaacckk: Controlrecordings stored in HDD.
AAuuddiioo OOuutt ttoo HHoommee TThheeaatteerr ssppeeaakk--eerr//AAuuddiioo OOuutt ttoo TTVV: Select HomeTheater speaker or TV speaker for AudioOut.
SIMPLINK Functions
1
2
3
4
5
GG When no device is connected(displayed in gray)
GG Selected Device
GG When a device is connected(displayed in bright color)
1
2
3
4
5
Display SSIIMMPPLLIINNKK menu.
Select the desired device.
Control connected AV devices.
1TV
3
2ENTER
ENTER
US
B
USB
ENTRY MODES
64
When you connect a USB device, this screen is displayed automatically.
In USB device, you can not add a new folder or delete the existing folder.
Precautions when using the USB device
GG Only a USB storage device is recognizable.
GG If the USB storage device is connected through aUSB hub, the device is not recognizable.
GG A USB storage device using an automatic recogni-tion program may not be recognized.
GG A USB storage device which uses its own drivermay not be recognized.
GG In case of a card reader, up to four memory cardsare concurrently recognizable.
GG The recognition speed of a USB storage devicemay depend on each device.
GG Please do not turn off the TV or unplug the USBdevice when the connected USB storage device isworking. When such device is suddenly separatedor unplugged, the stored files or the USB storagedevice may be damaged.
GG Please do not connect the USB storage devicewhich was artificially maneuvered on the PC. Thedevice may cause the product to malfunction orfail to be played. Never forget to use only a USBstorage device which has normal music files orimage files.
GG Please use only a USB storage device which wasformatted as a FAT or NTFS file system providedwith the Windows operating system. In case of astorage device formatted as a different utility pro-gram which is not supported by Windows, it maynot be recognized.
GG Please connect power to a USB storage devicewhich requires an external power supply. If not,the device may not be recognized.
GG Please connect a USB storage device with cable isoffered by USB maker. If connected with cable isnot offered by USB maker or an excessively longcable, the device may not be recognized.
GG Some USB storage devices may not be supportedor operated smoothly.
GG File alignment method of USB storage device issimilar to Window XP and filename can recognizeup to 100 English characters.
GG Please backup important files because data onUSB device may be damaged. Data management isconsumer's responsibility and as a result, the man-ufacturer does not cover data damage.
When removing the USB device
Connect the USB device to the UUSSBB IINN
jacks on the side of TV.
3
Select PPHHOOTTOO LLIISSTT or MMUUSSIICC LLIISSTT
1
MI I
N 3
USB
IN
PHOTO LIST MUSIC LIST
Select UUSSBB EEjjeecctt.
Select the UUSSBB EEjjeecctt menu before removing theUSB device.
2
ENTER
1Q. MENU
2ENTER
* Except 32/37/42LG30
� It doesn’t support USB HDD
� This TV supports JPG and MP3.
PHOTO LIST
US
B
65
You can view .JPG files from USB storage devices.
The On Screen Display on your model may be slightly different.
Screen Components
Moves to upper level file
Preview: Display the
thumbnail/folder name of
the photo in the selected
folder
Current page/Total pages
Total number of marked photos
Usable USB memory
Corresponding buttons on
the remote control
Supported photo file: *.JPG
� You can play JPG files only.
� Only baseline scan is supported among JPG.
USB Device
Page 1/1 No MarkedPHOTO LIST
Upper
Free Space 150MB
Navigate PopUp Menu Move Page Mark Exit
2Folders, 4Files
3 4 5
1
1
2
Select UUSSBB. Select PPHHOOTTOO LLIISSTT.2
TOP FOLDER
Drive1
1MENU
ENTER ENTER
1
2
3
4
5
6
Drive1
CH FAV RETURN
6
US
B
66
USB
Photo Selection and Popup Menu
USB Device
Page 1/1 No MarkedPHOTO LIST
Upper
Free Space 150MB
2Folders, 4Files
USB Device
Page 1/1 No MarkedPHOTO LIST
Upper
Free Space 150MB
1366x768 125KB
Select the target folder or drive.
Select the desired photos.2
Show the Popup menu.3
1
� Use the CCHH button to navigation in thephoto page.
� Use the FFAAVV button to mark or unmark aphoto. When one or more photos are marked,you can view individual photos or a slide showof the marked photos. If no photos are marked,you can view all photos individually or all pho-tos in the folder in a slide show.
TOP FOLDERDrive1
4 Select the desired Popup menu.
ENTER
ENTER
ENTER
Navigate Move Page Mark ExitCH FAV RETURNPopUp Menu
Navigate Move Page Mark ExitCH FAV RETURNPopUp Menu
Drive1
Drive1Butterfly
Upper Photo X.Box1366x768125KB
View
Mark All
Delete
Cancel
When you select a file (not folder), this PopUpmenu is displayed.
GG VViieeww: Display the selected item.
GG MMaarrkk AAllll: Mark all photos on the screen.
GG UUnnmmaarrkk AAll ll: Deselect all marked photos.
GG DDeelleettee: Delete the selected photo item.
GG CCaanncceell: Close the pop-up menu.
US
B
67
Full Screen Menu
You can change the Photo List view so that it fills the screen. More operations are available in full
screen mode.
� Use the CCHH button to navigation in thephoto page.
The aspect ratio of a photo may change the size ofthe photo displayed on the screen in full size.
1/17
Sideshow BGM Delete Option Hide
Select the target folder or drive.
Select the desired photos.
Show the Popup menu.
5
Select VViieeww.
The selected photo is displayed infull size.
2
3
1
4
ENTER
ENTER
ENTER
USB Device
Page 1/1 No MarkedPHOTO LIST
Upper
Free Space 150MB
2Folders, 4Files
USB Device
Page 1/1 No MarkedPHOTO LIST
Upper
Free Space 150MB
1366x768 125KB
TOP FOLDERDrive1
Navigate Move Page Mark ExitCH FAV RETURNPopUp Menu
Navigate Move Page Mark ExitCH FAV RETURNPopUp Menu
Drive1
Drive1Butterfly
Upper Photo X.Box1366x768125KB
View
Mark All
Delete
Cancel
US
B
68
USB
1/17
Sideshow BGM Delete Option Hide
Select the SSiiddeesshhooww, BBGGMM, ((RRoottaattee)),DDeelleettee, OOppttiioonn, or HHiiddee..
Press FF GG to set the time interval between slides.
Slide Speed Fast
Cancel
...Music Folder
ENTER
� Use button to select the previous ornext photo.
� Use button to select and controlthe menu on the full-sized screen.
ENTER
6
GG SSiiddeesshhooww: Selected photos are displayed during theslide show. If no photo is selected, all photos in the cur-rent folder are displayed during slide show.� Set the time interval of the slide show in OOppttiioonn.� A slide show continues for a maximum of 4 hours.
After 4 hours, the slide show will end and go to TVmode or external input mode.
GG BBGGMM: Listen to music while viewing photos in full size. � Set the BGM device and album in OOppttiioonn.
GG OOppttiioonn: Set values for SSll iiddee SSppeeeedd and MMuussiiccFFoollddeerr. � Use button and EENNTTEERR button to set values.
Then go to and press EENNTTEERR to save the set-tings.
� You cannot change MMuussiicc FFoollddeerr while BGM isplaying.
GG HHiiddee : Hide the menu on the full-sized screen.� To see the menu again on the full-sized screen, press
EENNTTEERR button to display.
NOTE!
GG This TV will not be able to decodemost JPEG images saved using theProgressive option.
MUSIC LIST
US
B
69
You can use the Music List menu to play MP3 files form a USB storage device.
This TV cannot play back copy-protected files.
The On Screen Display on your model may be slightly different.
Screen Components
Supported music file: *.MP3
Bit rate range 40Kbps ~ 320Kbps
• Sampling rate (Sampling Frequency)
MPEG1 : 32000, 44100, 48000Hz
MPEG2 : 16000, 24000, 22050Hz
MPEG2.5 : 16 ~ 48KHz
Moves to upper level file
Preview: If any album jacket
for the file exists, this jack-
et is displayed.
Current page/Total pages
Total number of marked
musics
Usable USB memory
Corresponding buttons on
the remote control
1
3
4
5
6
2
Select UUSSBB. Select MMUUSSIICC LLIISSTT.1 2
MENUENTER ENTER
USB DeviceMUSIC LIST
Upper
Free Space 150MB
3945 KB, 128 Kbps
Title Play Time
Upper
Good Bye
Arirang 04:12
05:30
3 45
1
2
Navigate PopUp Menu Move Page Mark ExitCH FAV RETURN
6
Page 1/1 No Marked
Drive1
Arirang
US
B
USB
70
Music Selection and Popup Menu
� Use the CCHH button to navigation inthe music page.
� Use FFAAVV button to mark or unmark a musicfile. If no music is marked, all the music in thefolder will be played in sequence. When one ormore music files are marked, the marked musicfiles will be played in sequence. If you want tolisten to only one song repeatedly, just markthat one file and play.
Up to 6 music titles are listed per page.
Select the target folder or drive.
Select the desired musics.
Show the Popup menu.
Select the desired Popup menu.
2
3
1
4
ENTER
ENTER
ENTER
5RETURN Return to TV viewing
USB Device
Page 1/1 No MarkedMUSIC LIST
Upper
Free Space 150MB
3945 KB, 128 Kbps
Drive1
Arirang
Navigate Move Page Mark ExitCH FAV RETURNPopUp Menu
Play TimeTitle
Upper
Good Bye
Arirang
USB Device
Page 1/1 No MarkedMUSIC LIST
Upper
Free Space 150MB
3945 KB, 128 Kbps
Drive1
Arirang
Navigate Move Page Mark ExitCH FAV RETURNPopUp Menu
Play TimeTitle
Upper
Good Bye
Arirang
05:30
04:12
3945 KB128 Kbps
Play
Play with Photo
Mark All
Delete
Cancel
GG PPllaayy (During stop): Play the selected music.
Once a song finishes playing, the next selectedone will be played. When there are no selectedmusics to play, the next one in the current fold-er will be played. If you go to a different folderand press the EENNTTEERR button, the currentmusic in playback will stop.
GG PPllaayy MMaarrkkeedd: Play the selected musics. Oncea music finishes playing, the next selected onewill be played automatically.
GG SSttoopp PPllaayy (During playback): Stop the play-ing musics.
GG PPllaayy wwiitthh PPhhoottoo: Start playing the selectedmusics and then move to the Photo List.
GG MMaarrkk AAll ll: Mark all musics in the folder.
GG UUnnmmaarrkk AAll ll: Deselect all marked music.
GG DDeelleettee: Delete the selected music.
GG CCaanncceell: Close the pop-up menu.
US
B
71
� The play information box (as shown below) will automaticallymove across the screen when there is no user input to pre-vent a fixed image remaining on the screen for a extendedperiod of time.
NOTE!
GG When music is playing, is displayed in front of the music play time.
GG A damaged or corrupted music file that does not play displays 00:00 as the play time.
GG Music files with copy-protection will not play.
GG Press EENNTTEERR, AA , or RREETTUURRNN button to stop the screen saver.
GG This TV can not play music files less than 16 Kbytes.
PIC
TU
RE
CO
NT
RO
L
72
PICTURE SIZE (ASPECT RATIO) CONTROL
PICTURE CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
� RGB-PC input source use 4:3 or 16:9 aspect ratio.
NOTE!
GG If a fixed image is displayed on the screen for a long time, the image could become imprinted on thescreen and remain visible.
This phenomenon is common to all manufacturers and is not covered by warranty. Although, after watch-ing video that did not fill the screen, any after-image from the black bars will normally dissipate after a fewminutes.
� You can also adjust AAssppeecctt RRaattiioo inthe QQ--MMeennuu.
EnterMovePICTURE
E
EnterMovePICTURE
E
R G
Aspect Ratio : 16:9
Picture Mode : Standard
• Backlight 80
• Contrast 90
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
Aspect Ratio : 16:9
Picture Mode : Standard
• Backlight 80
• Contrast 90
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0 R G
Set By Program
4:3
16:9
Zoom1
Zoom2
Just Scan
Select PPIICCTTUURREE.
Select AAssppeecctt RRaattiioo.
Select the desired picture format.
1MENU
3
2ENTER
ENTER
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
PIC
TU
RE
CO
NT
RO
L
73
Set by program
Selects the proper picture proportion to matchthe source’s image.
4:3
Choose 4:3 when you want to view a picturewith an original 4:3 aspect ratio.
16:9
Adjust the picture horizontally, in a linear pro-portion to fill the entire screen.
Zoom 1
Choose Zoom 1 when you want to view the pic-ture without any alteration. However, the top andbottom portions of the picture will be cropped.
Zoom 2
Choose Zoom 2 when you want the picture to bealtered, both vertically extended and cropped.The picture taking a halfway trade off betweenalteration and screen coverage.
Just Scan
Normally the edges of video signals are cropped1-2%. Just Scan turns off this cropping andshows the complete video.
Notes: If there is noise on the edges of the originalsignal, it will be visible when Just Scan is activated.
JJuusstt SSccaann operates only inDTV/CADTV/Component/HDMI-DTV/DVI-DTV(720p/1080i/1080p) input source.
(4:3 4:3)
(16:9 16:9)
PIC
TU
RE
CO
NT
RO
L
74
PRESET PICTURE SETTINGS
PICTURE CONTROL
Picture Mode - Preset
There are factory presets for picture settings available in the user menus. You can use a preset, change each
(Only for 50/60PG60, 50/60PG70) ,SSppoorrtt, or GGaammee.
� When selecting IInntteell ll iiggeenntt SSeennssoorr
(Except 32/37/42LG30, Plasma TV), the most suitable picture is automaticallyadjusted according to the surroundingconditions.
� VViivv iidd, SSttaannddaarrdd, CCiinneemmaa//CCiinneemmaa, SSppoorrtt, and GGaammee Settings arepreset for the optimum picture quality atthe factory and are not adjustable.
� You can also adjust PPiiccttuurree MMooddee inthe QQ.. MMeennuu.
� Cinema (Only for 50/60PG60,50/60PG70): This is cinema qualitymode to provide you the experience ofwatching a movie at home. The user willbe able enjoy the best level of satisfac-tory screen quality in any movie withoutany separate adjustments. Cinemaexpresses the optimal screen qualitywhen it is darkest.
� When selecting CCiinneemmaa, Aspectratio changes to Just scan.
� (Thomlinson Holman’s Experiment) is theaudio and video certification standard of THXestablished by George Lucas, who directed themovie Star Wars, and Thomlinson. This is the product to be certified in THX displayarea and guarantees screen quality that exceeds thedisplay standard specification in both hardware andsoftware.
1MENU
3
2ENTER
ENTER
Aspect Ratio : 16:9
Picture Mode : Standard
• Backlight 80
• Contrast 90
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0 R G
Intelligent Sensor
Vivid
Standard
Cinema
Sport
Game
Expert1
Expert2
Vivid
Standard
Cinema
Sport
Game
Expert1
Expert2
Vivid
Standard
Cinema
Sport
Game
Expert1
Expert2
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
32/37/42LG30,
42/50PG25
50/60PG60,50/60PG70
37/42/47/52LG50,
32/37/42/47/52LG60,
32/42/47/52LG70,
42/47LGX, 47LG90
PIC
TU
RE
CO
NT
RO
L
75
Color Tone - Preset
Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to
cool to see less intense colors with more blue.
EnterMovePICTURE
E
Select PPIICCTTUURREE.
Select CCoolloorr TTeemmppeerraattuurree.
1MENU
3ENTER
Select CCooooll, MMeeddiiuumm, or WWaarrmm.4
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
Select AAddvvaanncceedd CCoonnttrrooll.2
ENTER
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
R G
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R G
Color Temperature FF Medium GG
Fresh Contrast Off
Fresh Color Off
Noise Reduction Off
Gamma Medium
Black Level Low
Eye Care Off
Real Cinema Off
TruMotion High
Close
PIC
TU
RE
CO
NT
RO
L
76
MANUAL PICTURE ADJUSTMENT
PICTURE CONTROL
Picture Mode - User Mode
Adjust the picture appearance to suit your preference and viewing situations.
LCD TV only: This feature is disable in “PPiiccttuurree MMooddee--IInntteell ll iiggeenntt SSeennssoorr”.
50/60PG60, 50/60PG70 only: This feature is disabled in “PPiiccttuurree MMooddee-- CCiinneemmaa”.
Use this feature to see the difference TruMotion makes.TruMotion works with all inputs except PC mode.
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R G
Select PPIICCTTUURREE.
Select TTrruuMMoottiioonn DDeemmoo.
1MENU
2ENTER
3
4
ENTER Begin TTrruuMMoottiioonn DDeemmoo.
MENUStop TTrruuMMoottiioonn DDeemmoo.
RETURNReturn to TV viewing.
ExitRETURN
TruMotion provides even better quality for movies than 3:2 Pull-Down conversions. TruMotion means the panel supports faster frame rates that normal panels which makes for smoother motionin video. TruMotion LCD models support 120Hz instead of 60Hz. This means twice the information on thescreen in the same amount of time and easier film conversions (120 is equally divisible by 24, so no interpre-tations or double frames are needed).TruMotion works with all inputs except PC mode.
PIC
TU
RE
CO
NT
RO
L
83
LOCAL DIMMING - Only 47LG90
After analyzing the signal of the input video by areas of the screen, it adjusts the backlight to improve the
contrast ratio. This feature is disabled in “PPiiccttuurree MMooddee--CCiinneemmaa,, GGaammee”.
EnterMovePICTURE
E
• Color 60
• Tint 0
• Advanced Control
• Reset
Local Dimming : On
Screen (RGB-PC)
TruMotion Demo
Local Dimming Demo
R G
EnterMovePICTURE
E
• Color 60
• Tint 0
• Advanced Control
• Reset
Local Dimming : On
Screen (RGB-PC)
TruMotion Demo
Local Dimming Demo
R G
Off
On
Select PPIICCTTUURREE.
Select LLooccaall DDiimmmmiinngg.
1MENU
2ENTER
Select OO nn or OOff ff.
3ENTER
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
LOCAL DIMMING DEMO - Only 47LG90
Use this feature to see the difference Local Dimming makes.
Settings of the selected picture modes return to the default factory settings.
Select PPIICCTTUURREE.
Select RReesseett.
Initialize the adjusted value.
1MENU
3
2ENTER
ENTER
4MENU
Return to TV viewing.
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R G
EnterMovePICTURE
E
• Brightness 50
• Sharpness 60
• Color 60
• Tint 0
• Advanced Control
• Reset
Screen (RGB-PC)
TruMotion Demo
R GResetting video configuration...ii
PIC
TU
RE
CO
NT
RO
L
85
POWER INDICATOR - LCD TV Only
Select OOPPTTIIOONN.
Select PPoowweerr IInnddiiccaattoorr.
1MENU
2ENTER
Select SSrraarr ttuupp SSoouunndd, SSttaannddbbyyLLiigghhtt, PPoowweerr LLiigghhtt or DDeemmoo MMooddee.
3ENTER
Select your desired options.
4
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
� SSttaarrttuupp SSoouunndd: You can turn off thestarting sound of the TV or set the vol-ume.
� SSttaannddbbyy LLiigghhtt: You can set thebrightness of the LED on the front sideof the TV during power standby.
� PPoowweerr LLiigghhtt: You can set the the LEDon the front side of the TV to be turnedon or off while watching the TV.
� DDeemmoo MMooddee: You can set the LED onthe front side of the TV to flash.
EnterMoveOPTIONLanguage : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
Set ID : 1
Power Indicator
Initial Setting : Home
EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
Set ID : 1
Power Indicator
Initial Setting : Home
Standby Light
On
Demo Mode Off
Srartup Sound
Off
Close
FF Low GG
Power Light
Only for
32/37/42/47/52LG60,
42/47LGX
PIC
TU
RE
CO
NT
RO
L
86
IMAGE STICKING MINIMIZATION (ISM) METHOD - Plasma TV Only
PICTURE CONTROL
A frozen still picture from a PC/video game displayed on the screen for prolonged periods can result in a ghost
image. You can use Orbiter to help prevent image sticking. The other two functions are for removing a ghost
image.
GG An excessive ghosted image may be impossible toclear entirely with White Wash. To return to nor-mal viewing, press the any button.
NOTE!
EnterMoveOPTIONLanguage : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Normal
Orbiter
Inversion
White Wash
EE
� NNoorrmmaall: If image sticking is never aproblem, ISM is not necessary - set toNormal.
� OOrrbb ii ttee rr: Orbiter may help preventghost images. However, it is best not toallow any fixed image to remain on thescreen. To avoid a ghost image on thescreen, the image will move every 2 min-utes.
� IInnvveerrssiioonn: Inversion will automaticallyinvert the plasma display panel colorevery 30 minutes.
� WWhhii ttee WWaasshh: White Wash removesghost images from the screen. Use spar-ingly. Watch the TV normally for a whilebefore using this feature to see if theghost image disappears on its own.
Select OOPPTTIIOONN.
Select IISSMM MMeetthhoodd.
1MENU
2ENTER
Select NNoorrmmaall ,, OOrrbbiitteerr,,IInnvveerrssiioonn or WWhhiittee WWaasshh..
3ENTER
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1EE
PIC
TU
RE
CO
NT
RO
L
87
POWER SAVING PICTURE MODE - Plasma TV Only
It reduces the plasma display’s power consumption.
EnterMoveOPTION EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Level 0
Level 1
Level 2
Level 3
Level 4
� Level 0 is the brightest.
� Level 0 > Level 1 > Level 2 > Level 3 >Level 4
� You can also adjust PPoowweerr SSaavviinngg inthe QQ.. MMeennuu.
Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a
regular TV program.
Select AAUUDDIIOO.
Select AAuuttoo VVoolluummee.
Select OO nn or OOff ff.
EnterMoveAUDIO
E
L R
EnterMoveAUDIO
E
L R
1MENU
3
2ENTER
ENTER
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Auto Volume : On
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Off
On
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
89
PRESET SOUND SETTINGS (SOUND MODE)
Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate
sound options based on the program content.
SSttaannddaarrdd, MMuussiicc, CCiinneemmaa, SSppoorrtt, and GGaammee are preset for optimum sound quality at the factory and are
not adjustable.
Select AAUUDDIIOO.
Select SSoouunndd MMooddee.
Select SSttaannddaarrdd, MMuussiicc,CCiinneemmaa, SSppoorrtt, or GGaammee.
1MENU
3
2ENTER
ENTER
EnterMoveAUDIO
E
L R
EnterMoveAUDIO
E
L R
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Standard
Music
Cinema
Sport
Game
� You can also adjust SSoouunndd MMooddee inthe QQ.. MMeennuu.
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
90
SOUND & LANGUAGE CONTROL
SOUND SETTING ADJUSTMENT - USER MODE
SRS TRUSURROUND XT
Adjust the sound to suit your taste and room situations.
Select AAUUDDIIOO.
Select SSoouunndd MMooddee.
Select TTrreebbllee or BBaassss.
1MENU
4
2ENTER
Select SSttaannddaarrdd, MMuussiicc,CCiinneemmaa, SSppoorrtt, or GGaammee.
3ENTER
ENTER
EnterMoveAUDIO
L R
E
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
EnterMoveAUDIO
L R
E
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Select AAUUDDIIOO.
Select SSRRSS TTrruuSSuurrrroouunndd XXTT
Select OO nn or OOff ff.
1MENU
3
2ENTER
ENTER� SSRRSS TTrruuSSuurrrroouunndd XXTT: Takes advantage of
any multi-channel format without needing toadd extra speakers or equipment. Dialog clarity,bass enrichment, and the addition of stereoaudio enhancement produces an immersivesound experience from standard stereo material.
6RETURN
Return to the previous menu.
MENUReturn to TV viewing.
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
Close
EE
EE
Treble 50
Bass 50
SRS TruSurround XT Off
Make appropriate adjustments.5
ENTER
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
91
CLEAR VOICE
By differentiating the human sound range from others, it improves the sound quality of voices.
� If you select “CClleeaarr VVooiiccee--OOnn”, SSRRSSTTrruuSSuurrrroouunndd XXTT feature will notwork.
� You can also adjust CClleeaarr VVooiiccee in theQQ--MMeennuu.
EnterMoveAUDIO
E
L R
EnterMoveAUDIO
E
L R
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Off
On
Select AAUUDDIIOO.
Select CClleeaarr VVooiiccee.
Select OO nn or OOff ff.
1MENU
3
2ENTER
ENTER
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
92
BALANCE
SOUND & LANGUAGE CONTROL
Select AAUUDDIIOO.
Select BBaallaannccee.
Make appropriate adjustments.
1MENU
3
2ENTER
ENTER
Adjust the left/right sound of speaker to suit your taste and room situations.
EnterMoveAUDIO EnterMoveAUDIO
L R
E
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
L R
E
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Close
EE
EE
Balance 0 L R
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
93
TV SPEAKERS ON/OFF SETUP
Turn the TV speakers off if using external audio equipment.
EnterMoveAUDIO
E
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
TV Speaker : On
Select AAUUDDIIOO.
Select TTVV SSppeeaakkeerr.
Select OO nn or OOff ff.
1MENU
3
2ENTER
ENTER
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
L R
EnterMoveAUDIO
E
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
TV Speaker : On
L R
Off
On
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
94
AUDIO RESET
SOUND & LANGUAGE CONTROL
Settings of the selected Sound Mode return to the default factory settings.
Select AAUUDDIIOO.
Select RReesseett.
1MENU
2ENTER
Initialize the adjusted value.
3ENTER
EnterMoveAUDIO
E
L R
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
Resetting audio configuration...ii
4MENU
Return to TV viewing.
EnterMoveAUDIO
L R
E
Auto Volume : Off
Clear Voice : On
Balance 0
Sound Mode : Standard
• SRS TruSurround XT: Off
• Treble 50
• Bass 50
• Reset
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
95
STEREO/SAP BROADCAST SETUP
For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accom-
panies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used
if the broadcast is only in Mono.
Q.Menu
Close
3
16:9
Vivid
Off
Standard
Off
FF English GG
Off
Add
Eject
Aspect Ratio
Backlight
Clear Voice
Picture Mode
Sound Mode
Caption
Multi Audio
Sleep Timer
Del/Add/Fav
USB Eject
CH
Select SSAAPP.
Select MMoonnoo, SStteerreeoo, or SSAAPP.
Return to TV viewing.
1Q. MENU
3
2
Q. MENU
Select MMuulltt ii AAuuddiioo.
Select other languages.
Return to TV viewing.
1Q. MENU
3
2
Q. MENU
Analog TV Digital TV
Q.Menu
Close
3
16:9
Vivid
Off
Standard
Off
FF English GG
Off
Add
Eject
Aspect Ratio
Power Saving
Clear Voice
Picture Mode
Sound Mode
Caption
Multi Audio
Sleep Timer
Del/Add/Fav
USB Eject
CH
LCD TVPlasma TV
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
96
AUDIO LANGUAGE
SOUND & LANGUAGE CONTROL
Other languages may be available if a digital signal is provided by the broadcasting station.
This feature operates only in DTV/CADTV mode.
Select OOPPTTIIOONN.
Select LLaanngguuaaggee.
Select AAuuddiioo.
1MENU
3
2ENTER
ENTER
Select your desired language:EEnnggll iisshh, SSppaanniisshh, or FFrreenncchh
4
EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Menu English
Audio FF English GG
Close
EnterMoveOPTION
EE
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
97
ON-SCREEN MENUS LANGUAGE SELECTION
The menus can be shown on the screen in the selected language.
Select OOPPTTIIOONN.
Select LLaanngguuaaggee.
Select MMeennuu.
1MENU
3
2ENTER
ENTER
Select your desired language.
From this point on, the on-screen menuswill be shown in the selected language.
4
EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
EnterMoveOPTION
EE
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Menu FF English GG
Audio English
Close
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
98
CAPTION MODE
SOUND & LANGUAGE CONTROL
Caption must be provided to help people with hearing loss watch TV. Select a caption mode for displaying cap-
tioning information if provided on a program. Analog caption displays information at any position on the screen
and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both
digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode
which was last set when you turned the power off. This function is only available when CCaappttiioonn Mode is set OO nn.
Select OOPPTTIIOONN.
Select CCaappttiioonn.
Select OO nn.
1MENU
3
2ENTER
ENTER
Select CCCC11-44 or TTeexxtt11-44.
4
EnterMoveOPTION EnterMoveOPTION
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : Off
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Caption : CC1
ISM Method : Normal
Power Saving : Level 0
Set ID : 1
Mode CC1
Close
Digital Option
FF On GG
Analog Broadcasting System Captions
� When selecting OOff ff, Sub-menus forAnalog, DTV, and Digital Optionbecome disabled.
� CCAAPPTTIIOONN
The term for the words that scrollacross the bottom of the TV screen;usually the audio portion of the pro-gram provided for the hearing impaired.
� TTEEXXTT
The term for the words that appear in alarge black frame and almost cover theentire screen; usually messages provid-ed by the broadcaster.
E E
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
SO
UN
D &
LAN
GU
AG
E C
ON
TR
OL
99
Digital Broadcasting System Captions
Choose the language you want the DTV/CADTV Captions to appear in.
Other Languages can be chosen for digital sources only if they are included on the program.
This function in only available when Caption Mode is set On.
TV will be automatically turned off, in case of no signal for 10 minutes.
EnterMoveTIME EnterMoveTIME
Clock : Feb/21/2008 2:10 AM
Off Time : Off
On Time : Off
Sleep Timer : Off
Auto Sleep : Off
Clock : Feb/21/2008 2:10 AM
Off Time : Off
On Time : Off
Sleep Timer : Off
Auto Sleep : On
Select TTIIMMEE.
Select AAuuttoo SSlleeeepp.
Select OO nn or OOff ff.
1MENU
3
2ENTER
ENTER
Off
On
TV will be automatically turned off, in case of No Signal for 10 minutes.
4RETURN
Return to the previous menu.
MENUReturn to TV viewing.
PAR
EN
TAL C
ON
TR
OL / R
AT
ING
106
PARENTAL CONTROL / RATINGS
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broad-casting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing thetype of the program and the categories. It is also possible to block all program viewing for a time period. To usethis function, the following must be done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
V-Chip rating and categoriesRating guidelines are provided by broadcasting stations. Most television programs and television movies can beblocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
Ratings for Television programs including made-for-TV movies :
� TV-G (General audience)
� TV-PG (Parental guidance suggested)
� TV-14 (Parents strongly cautioned)
� TV-MA (Mature audience only)
� TV-Y (All children)
� TV-Y7 (Children 7 years older)
Set up blocking schemes to block specific channels, ratings, and external viewing sources.
A password is required to gain access to this menu.
Setting up Your Password
For USA
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
For Canada
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
TV Rating-English
TV Rating-French
Downloadable Rating
Input Block
Close
Enter Password
* * * *
Select LLOOCCKK.1
MENUENTER
Input the password.2 1
4 5 6
7 8
0
9
2 3
� Enter the password as requested.
� The TV is set up with the initial pass-word “0-0-0-0”.
SET PASSWORD & LOCK SYSTEM
PAR
EN
TAL C
ON
TR
OL / R
AT
ING
107
Enables or disables the blocking scheme you set up previously.
Lock System
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Select LLoocckk SSyysstteemm.
Select OO nn or OOff ff.
4
3
ENTER
EnterMoveLOCK
Lock System : On
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Off
On
� When you select OO nn, the Lock Systemis enable.
Select LLOOCCKK.1
MENUENTER
Input the password.2 1
4 5 6
7 8
0
9
2 3
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
PAR
EN
TAL C
ON
TR
OL / R
AT
ING
108
PARENTAL CONTROL / RATINGS
Change the password by inputting a new password twice.
Set Password
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Select SSeett ppaasssswwoorrdd.
Choose any 4 digits for your new password.
As soon as the 4 digits are entered, re-enterthe same 4 digits on the CCoonnff ii rrmm.
4
3
ENTER
1
4 5 6
7 8
0
9
2 3
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Close
New * * * *
Confirm * * * *
Select LLOOCCKK.1
MENUENTER
Input the password.2 1
4 5 6
7 8
0
9
2 3
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
PAR
EN
TAL C
ON
TR
OL / R
AT
ING
109
CHANNEL BLOCKING
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Select BBlloocckk CChhaannnneell.
Select a channel to block or unblock.
4
3
ENTER
Block or unblock a channel.5
ENTER
Blocks any channels that you do not want to watch or that you do not want your children to watch.
Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You canset the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind thatthe movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Select MMoovviiee RRaattiinngg.
Select GG, PP GG, PPGG--1133, RR, NNCC--1177,XX, or BBlloocckkiinngg OOffff.
4
3
ENTER
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Blocking off : Permits all programs
G
PG
PG-13
R
NC-17
X
Blocking Off
� G (General audience)
� PG (Parental guidance suggested)
� PG-13 (Parents strongly cautioned)
� R (Restricted)
� NC-17 (No one 17 and under admitted)
� X (Adult only)
� Blocking Off (Permits all programs)
GG If you set PG-13: G and PG movies willbe available, PG-13, R, NC-17 and X willbe blocked.
Select LLOOCCKK.1
MENUENTER
Input the password.2 1
4 5 6
7 8
0
9
2 3
5RETURN
Return to the previous menu.
MENUReturn to TV viewing.
PAR
EN
TAL C
ON
TR
OL / R
AT
ING
111
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Select TTVV RRaattiinngg--CChhii llddrreenn.
Select AAggee or FFaannttaassyy VViioolleennccee.4
3
ENTER
Select block options.
5ENTER
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
� Age (applies to TV-Y, TV-Y7)
� Fantasy Violence (applies to TV-Y7)
TV Rating Children - For USA only
Prevents children from watching certain children's TV programs, according to the ratings limit set. The children
rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audi-
ences in the TV Rating - sub menu, your children can view those programs.
Close
Age
Fantasy Violence
Select LLOOCCKK.1
MENUENTER
Input the password.2 1
4 5 6
7 8
0
9
2 3
6RETURN
Return to the previous menu.
MENUReturn to TV viewing.
PAR
EN
TAL C
ON
TR
OL / R
AT
ING
112
PARENTAL CONTROL / RATINGS
TV Rating General - For USA only
Based on the ratings, blocks certain TV programs that you and your family do not want to view.
EnterMoveLOCK
Lock System : Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Select TTVV RRaattiinngg--GGeenneerraall.
Select AAggee, DDiiaalloogguuee, LLaanngguuaaggee,SSeexx or VViioolleennccee.
� Check to see if there is any object between the product and the remote controlcausing obstruction. Ensure you are pointing the remote control directly at the TV.
� Ensure that the batteries are installed with correct polarity (+ to +, - to -).
� Ensure that the correct remote operating mode is set: TV, VCR etc.
� Install new batteries.
� Is the sleep timer set?
� Check the power control settings. Power interrupted.
� Check whether the product is turned on.
� Try another channel. The problem may be with the broadcast.
� Is the power cord inserted into wall power outlet?
� Check your antenna direction and/or location.
� Test the wall power outlet, plug another product’s power cord into the outletwhere the product’s power cord was plugged in.
� This is normal, the image is muted during the product startup process. Pleasecontact your service center, if the picture has not appeared after five minutes.
� Adjust Color in menu option.
� Keep a sufficient distance between the product and the VCR.
� Try another channel. The problem may be with the broadcast.
� Are the video cables installed properly?
� Activate any function to restore the brightness of the picture.
� Check for local interference such as an electrical appliance or power tool.
� Station or cable product experiencing problems, tune to another station.
� Station signal is weak, reorient antenna to receive weaker station.
� Check for sources of possible interference.
� Check antenna (Change the direction of the antenna).
� Check HDMI cable over version 1.3.
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screendisplay. In this case use the latest cables that support HDMI version 1.3.
� Try another channel. The problem may be with the broadcast.
� Are the audio cables installed properly?
� Adjust Balance in menu option.
� A change in ambient humidity or temperature may result in an unusual noisewhen the product is turned on or off and does not indicate a fault with theproduct.
� Check HDMI cable over version 1.3.
� Check USB cable over version 2.0.
� Use normal MP3 file.
AP
PE
ND
IX
120
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarmwater and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and thenuse it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
� To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
� Please be sure not to use a wet cloth.
Extended Absence
GG If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplugthe power cord to protect against possible damage from lightning or power surges.
CAUTION
2
1
AP
PE
ND
IX
121
PRODUCT SPECIFICATIONS
� The specifications shown above may be changed without prior notice for quality improvement.
The provided universal remote control can be programmed to operate most remote-controllable devices.
Note that the remote may not control all models of other brands.
Programming a code into a remote mode
Testing your remote control.
To find out whether your remote control can operate other components without programming, turn on acomponent such as a STB and press the corresponding mode button (such as a SSTTBB) on the remote con-trol, while pointing at the component. Test the PPOOWWEERR and CC HH buttons to see if the componentresponds correctly. If the component does not operate correctly, the remote control requires programmingto operate the device.
Turn on the component to be programmed, then press the corresponding mode button (such as SSTTBB) onthe remote control. The remote control button of the desired device is illuminated.
Press the MMEENNUU and MMUUTTEE buttons simultaneously, and the remote control is ready to be programmed withthe code.
Enter a code number using the number buttons on the remote control. Programming code numbers for thecorresponding component can be found on the following pages. If the code is correct, the device will turnoff.
Press the MMEENNUU button to store the code.
Test the remote control functions to see if the component responds correctly. If not, repeat from step 2.
physical major major low minor high minor low attributeprogram high program lowm a
01. Power k a 00 ~ 01
02. Input Select x b (GG p.132)
03. Aspect Ratio k c (GG p.132)
04. Screen Mute k d 00 ~ 01
05. Volume Mute k e 00 ~ 01
06. Volume Control k f 00 ~ 64
07. Contrast k g 00 ~ 64
08. Brightness k h 00 ~ 64
09. Color k i 00 ~ 64
10. Tint k j 00 ~ 64
11. Sharpness k k 00 ~ 64
12. OSD Select k l 00 ~ 01
13. Remote Control
Lock Mode
Transmission / Receiving Protocol
TTrraannssmmiissssiioonn
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired TV IDnumber in Setup menu. Adjustment range is 1~ 99.When selecting Set ID ‘0’, every connected the TV iscontrolled. Set ID is indicated as decimal (1~ 99) onmenu and as Hexa decimal (0x0~ 0x63) on transmission/receiving protocol.
[DATA] : To transmit the command data.
Transmit the ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
* In this model, TV will not send the status during the standby mode.
OOKK AAcckknnoowwlleeddggeemmeenntt
The TV transmits ACK (acknowledgement) based on this for-mat when receiving normal data. At this time, if the data isdata read mode, it indicates present status data. If the data isdata write mode, it returns the data of the PC computer.
* In this model, TV will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[OK] : Use the large character.
EErrrroorr AAcckknnoowwlleeddggeemmeenntt
The TV transmits ACK (acknowledgement) based on this for-mat when receiving abnormal data from non-viable functionsor communication errors.
Data1: Illegal Code
Data2: Not supported function
Data3: Wait more time
* In this model, TV will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
2222.. CChhaannnneell AAdddd//DDeell ((CCoommmmaanndd:: mm bb))
To add and delete the channels
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel Delete Data 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
2233.. KKeeyy ((CCoommmmaanndd:: mm cc))
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code: Refer to page 128.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
2244.. BBaacckkll iigghhtt ((CCoommmmaanndd:: mm gg))
(Only LCD TV model)
To adjust screen backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping 1’. See page 133.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
Step
NTSC Air
NTSC Cable
ATSC Air
ATSC Cable_std
ATSC Cable_hrc
ATSC Cable_irc
ATSC cable_auto
Reserved
...
Reserved
1
0
0
1
1
0
0
1
1
x
1
2
0
0
0
0
1
1
1
1
x
1
3
0
0
0
0
0
0
0
0
x
1
4
x
x
x
x
x
x
x
x
x
x
Reserved5
0
1
Use
No Use
Using Physical
Channel6
0
1
Two
One
Two/One Part Channel
7
0
1
Main
Sub
Main/Sub
Picture0
0
1
0
1
0
1
0
1
x
1
AP
PE
ND
IX
136
OPEN SOURCE LICENSE - This feature is not available for all models.
APPENDIX
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies ofthis license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away yourfreedom to share and change it. By contrast, the GNU GeneralPublic License is intended to guarantee your freedom to shareand change free software - to make sure the software is free forall its users. This General Public License applies to most of theFree Software Foundation's software and to any other programwhose authors commit to using it. (Some other free softwarefoundation software is covered by the GNU Lesser General PublicLicense instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, notprice. Our General Public Licenses are designed to make sure thatyou have the freedom to distribute copies of free software (andcharge for this service if you wish), that you receive source codeor can get it if you want it, that you can change the software oruse pieces of it in new free programs; and that you know you cando these things.
To protect your rights, we need to make restrictions that forbidanyone to deny you these rights or to ask you to surrender therights. These restrictions translate to certain responsibilities foryou if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whethergratis or for a fee, you must give the recipients all the rights thatyou have. You must make sure that they, too, receive or can getthe source code. And you must show them these terms so theyknow their rights.
We protect your rights with two steps: (1) copyright the soft-ware, and (2) offer you this license which gives you legal permis-sion to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make cer-tain that everyone understands that there is no warranty for thisfree software. If the software is modified by someone else andpassed on, we want its recipients to know that what they have isnot the original, so that any problems introduced by others willnot reflect on the original authors' reputations.
Finally, any free program is threatened constantly by softwarepatents. We wish to avoid the danger that redistributors of a freeprogram will individually obtain patent licenses, in effect making
the program proprietary. To prevent this, we have made it clearthat any patent must be licensed for everyone's free use or notlicensed at all.
The precise terms and conditions for copying, distribution andmodification follow.
GNU GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTIONAND MODIFICATION
0. This license applies to any program or other work which con-tains a notice placed by the copyright holder saying it may bedistributed under the terms of this General Public License. The"Program", below, refers to any such program or work, and a"work based on the Program" means either the Program or anyderivative work under copyright law: that is to say, a work con-taining the Program or a portion of it, either verbatim or withmodifications and/or translated into another language.(Hereinafter, translation is included without limitation in theterm "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modificationare not covered by this license; they are outside its scope.The act of running the Program is not restricted, and the out-put from the program is covered only if its contents constitutea work based on the program (independent of having beenmade by running the program). Whether that is true dependson what the program does.
1. You may copy and distribute verbatim copies of the program'ssource code as you receive it, in any medium, provided thatyou conspicuously and appropriately publish on each copy anappropriate copyright notice and disclaimer of warranty; keepintact all the notices that refer to this license and to theabsence of any warranty; and give any other recipients of theprogram a copy of this license along with the Program.
You may charge a fee for the physical act of transferring acopy, and you may at your option offer warranty protection inexchange for a fee.
2. You may modify your copy or copies of the program or anyportion of it, thus forming a work based on the Program, andcopy and distribute such modifications or work under theterms of section 1 above, provided that you also meet all ofthese conditions:
a) You must cause the modified files to carry prominentnotices stating that you changed the files and the date ofany change.
GNU GENERAL PUBLIC LICENSEVersion 2, June 1991
AP
PE
ND
IX
137
b) You must cause any work that you distribute or publish,that in whole or in part contains or is derived from theProgram or any part there of, to be licensed as a whole atno charge to all third parties under the terms of thislicense.
c) If the modified program normally reads commands interac-tively when run, you must cause it, when started runningfor such interactive use in the most ordinary way, to printor display an announcement including an appropriatecopyright notice and a notice that there is no warranty (orelse, saying that you provide a warranty) and that usersmay redistribute the program under these conditions, andtelling the user how to view a copy of this license.(Exception: if the Program itself is interactive but does notnormally print such an announcement, your work based onthe Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. Ifidentifiable sections of that work are not derived from theProgram, and can be reasonably considered independent andseparate works in themselves, then this license, and its terms,do not apply to those sections when you distribute them asseparate works. But when you distribute the same sections aspart of a whole which is a work based on the Program, the dis-tribution of the whole must be on the terms of this license,whose permissions for other licensees extend to the entirewhole, and thus to each and every part regardless of whowrote it.
Thus, it is not the intent of this section to claim rights or con-test your rights to work written entirely by you; rather, theintent is to exercise the right to control the distribution ofderivative or collective works based on the program.
In addition, mere aggregation of another work not based onthe program with the Program (or with a work based on theprogram) on a volume of a storage or distribution mediumdoes not bring the other work under the scope of this license.
3. You may copy and distribute the program (or a work based onit, under section 2) in object code or executable form underthe terms of sections 1 and 2 above provided that you alsodo one of the following:a) Accompany it with the complete corresponding machine-
readable source code, which must be distributed under theterms of sections 1 and 2 above on a medium customarilyused for software interchange; or,
b) Accompany it with a written offer, valid for at least threeyears, to give any third party, for a charge no more thanyour cost of physically performing source distribution, acomplete machine-readable copy of the correspondingsource code, to be distributed under the terms of sections1 and 2 above on a medium customarily used for softwareinterchange; or,
c) Accompany it with the information you received as to theoffer to distribute corresponding source code. (This alter-native is allowed only for noncommercial distribution andonly if you received the program in object code or exe-cutable form with such an offer, in accord with Subsectionb above.)
The source code for a work means the preferred form of thework for making modifications to it. For an executable work,complete source code means all the source code for all mod-ules it contains, plus any associated interface definition files,plus the scripts used to control compilation and installationof the executable. However, as a special exception, the sourcecode distributed need not include anything that is normallydistributed (in either source or binary form) with the majorcomponents (compiler, kernel, and so on) of the operatingsystem on which the executable runs, unless that componentitself accompanies the executable.
If distribution of executable or object code is made by offer-ing access to copy from a designated place, then offeringequivalent access to copy the source code from the sameplace counts as distribution of the source code, even thoughthird parties are not compelled to copy the source along withthe object code.
4. You may not copy, modify, sublicense, or distribute the Programexcept as expressly provided under this license. Any attemptotherwise to copy, modify, sublicense or distribute theProgram is void, and will automatically terminate your rightsunder this license. However, parties who have received copies,or rights, from you under this license will not have their licens-es terminated so long as such parties remain in full compli-ance.
5. You are not required to accept this license, since you have notsigned it. However, nothing else grants you permission tomodify or distribute the Program or its derivative works.These actions are prohibited by law if you do not accept thislicense. Therefore, by modifying or distributing the program(or any work based on the program), you indicate your accep-tance of this license to do so, and all its terms and conditionsfor copying, distributing or modifying the program or worksbased on it.
6. Each time you redistribute the program (or any work based onthe Program), the recipient automatically receives a licensefrom the original licensor to copy, distribute or modify theProgram subject to these terms and conditions. You may notimpose any further restrictions on the recipients' exercise ofthe rights granted herein. You are not responsible for enforc-ing compliance by third parties to this license.
AP
PE
ND
IX
138
APPENDIX
7. If, as a consequence of a court judgment or allegation ofpatent infringement or for any other reason (not limited topatent issues), conditions are imposed on you (whether bycourt order, agreement or otherwise) that contradict the con-ditions of this license, they do not excuse you from the con-ditions of this license. If you cannot distribute so as to satis-fy simultaneously your obligations under this license and anyother pertinent obligations, then as a consequence you maynot distribute the program at all. For example, if a patentlicense would not permit royalty-free redistribution of theprogram by all those who receive copies directly or indirectlythrough you, then the only way you could satisfy both it andthis license would be to refrain entirely from distribution ofthe program.
If any portion of this section is held invalid or unenforceableunder any particular circumstance, the balance of the sectionis intended to apply and the section as a whole is intended toapply in other circumstances.
It is not the purpose of this section to induce you to infringeany patents or other property right claims or to contest valid-ity of any such claims; this section has the sole purpose ofprotecting the integrity of the free software distribution sys-tem, which is implemented by public license practices. Manypeople have made generous contributions to the wide rangeof software distributed through that system in reliance onconsistent application of that system; it is up to theauthor/donor to decide if he or she is willing to distributesoftware through any other system and a licensee cannotimpose that choice.
This section is intended to make thoroughly clear what isbelieved to be a consequence of the rest of this license.
8. If the distribution and/or use of the program is restricted incertain countries either by patents or by copyrighted inter-faces, the original copyright holder who places the programunder this license may add an explicit geographical distributionlimitation excluding those countries, so that distribution ispermitted only in or among countries not thus excluded. Insuch case, this license incorporates the limitation as if writtenin the body of this license.
9. The Free Software Foundation may publish revised and/ornew versions of the General Public License from time to time.Such new versions will be similar in spirit to the present ver-sion, but may differ in detail to address new problems or con-cerns.
Each version is given a distinguishing version number. If theprogram specifies a version number of this license whichapplies to it and "any later version", you have the option offollowing the terms and conditions either of that version or of
any later version published by the Free Software Foundation.If the program does not specify a version number of thislicense, you may choose any version ever published by theFree Software Foundation.
10.If you wish to incorporate parts of the program into other freeprograms whose distribution conditions are different, write tothe author to ask for permission. For software which is copy-righted by the Free Software Foundation, write to the FreeSoftware Foundation; we sometimes make exceptions for this.Our decision will be guided by the two goals of preserving thefree status of all derivatives of our free software and of pro-moting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,THERE IS NO WARRANTY FOR THE PROGRAM, TO THEEXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHENOTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "ASIS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITEDTO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRERISK AS TO THE QUALITY AND PERFORMANCE OF THEPROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVEDEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARYSERVICING, REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW ORAGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/ORREDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BELIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGESARISING OUT OF THE USE OR INABILITY TO USE THE PRO-GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATAOR DATA BEING RENDERED INACCURATE OR LOSSES SUS-TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THEPROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
AP
PE
ND
IX
139
END OF TERMS AND CONDITIONS
How to apply these terms to your new programs
If you develop a new program, and you want it to be of the great-est possible use to the public, the best way to achieve this is tomake it free software which everyone can redistribute and changeunder these terms.
To do so, attach the following notices to the program. It is safestto attach them to the start of each source file to most effective-ly convey the exclusion of warranty; and each file should have atleast the "copyright" line and a pointer to where the full notice isfound.
one line to give the program's name and a brief idea of what itdoes.Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/ormodify it under the terms of the GNU General Public License aspublished by the Free Software Foundation; either version 2 ofthe license, or (at your option) any later version.
This program is distributed in the hope that it will be useful, butWITHOUT ANY WARRANTY; without even the implied warrantyof MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-POSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General PublicLicense along with this program; if not, write to the Free SoftwareFoundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA02110-1301 USA.
Also add information on how to contact you by electronic andpaper mail.
If the program is interactive, make it output a short notice likethis when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of authorGnomovision comes with ABSOLUTELY NO WARRANTY; fordetails type ‘show w’. This is free software, and you are welcometo redistribute it under certain conditions; type ‘show c’ fordetails.
The hypothetical commands ‘show w’ and ‘show c’ should showthe appropriate parts of the General Public License. Of course,the commands you use may be called something other than‘show w’ and ‘show c’; they could even be mouse-clicks or menuitems-whatever suits your program.
You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for the pro-gram, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the pro-gram ‘Gnomovision’ (which makes passes at compilers) written byJames Hacker.
signature of Ty Coon, 1 April 1989Ty Coon, President of Vice
This General Public License does not permit incorporating yourprogram into proprietary programs. If your program is a subrou-tine library, you may consider it more useful to permit linking pro-prietary applications with the library. If this is what you want todo, use the GNU Lesser General Public License instead of thislicense.
AP
PE
ND
IX
140
APPENDIX
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51Franklin Street, Fifth Floor, Boston, MA 02110-1301 USAEveryone is permitted to copy and distribute verbatim copies ofthis license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It alsocounts as the successor of the GNU Library Public License, ver-sion 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away yourfreedom to share and change it. By contrast, the GNU GeneralPublic Licenses are intended to guarantee your freedom to shareand change free software - to make sure the software is free forall its users.
This license, the Lesser General Public License, applies to somespecially designated software packages - typically libraries - ofthe Free Software Foundation and other authors who decide touse it. You can use it too, but we suggest you first think careful-ly about whether this license or the ordinary General PublicLicense is the better strategy to use in any particular case, basedon the explanations below.
When we speak of free software, we are referring to freedom ofuse, not price. Our General Public Licenses are designed to makesure that you have the freedom to distribute copies of free soft-ware (and charge for this service if you wish); that you receivesource code or can get it if you want it; that you can change thesoftware and use pieces of it in new free programs; and that youare informed that you can do these things.
To protect your rights, we need to make restrictions that forbiddistributors to deny you these rights or to ask you to surrenderthese rights. These restrictions translate to certain responsibilitiesfor you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratisor for a fee, you must give the recipients all the rights that wegave you. You must make sure that they, too, receive or can getthe source code. If you link other code with the library, you mustprovide complete object files to the recipients, so that they canrelink them with the library after making changes to the libraryand recompiling it. And you must show them these terms so theyknow their rights.
We protect your rights with a two-step method: (1) we copyrightthe library, and (2) we offer you this license, which gives you legalpermission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear thatthere is no warranty for the free library. Also, if the library is mod-ified by someone else and passed on, the recipients should knowthat what they have is not the original version, so that the origi-nal author's reputation will not be affected by problems thatmight be introduced by others.
Finally, software patents pose a constant threat to the existenceof any free program. We wish to make sure that a company can-not effectively restrict the users of a free program by obtaining arestrictive license from a patent holder. Therefore, we insist thatany patent license obtained for a version of the library must beconsistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by theordinary GNU General Public License. This license, the GNULesser General Public License, applies to certain designatedlibraries, and is quite different from the ordinary General PublicLicense. We use this license for certain libraries in order to per-mit linking those libraries into non-free programs.
When a program is linked with a library, whether statically orusing a shared library, the combination of the two is legallyspeaking a combined work, a derivative of the original library. Theordinary General Public License therefore permits such linkingonly if the entire combination fits its criteria of freedom. TheLesser General Public License permits more lax criteria for linkingother code with the library.
We call this license the "Lesser" General Public License becauseit does Less to protect the user's freedom than the ordinaryGeneral Public License. It also provides other free software devel-opers Less of an advantage over competing non-free programs.These disadvantages are the reason we use the ordinary GeneralPublic License for many libraries. However, the Lesser license pro-vides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need toencourage the widest possible use of a certain library, so that itbecomes a de-facto standard. To achieve this, non-free programsmust be allowed to use the library. A more frequent case is thata free library does the same job as widely used non-free libraries.In this case, there is little to gain by limiting the free library to freesoftware only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-freeprograms enables a greater number of people to use a large bodyof free software. For example, permission to use the GNU CLibrary in non-free programs enables many more people to usethe whole GNU operating system, as well as its variant, theGNU/Linux operating system.
GNU LESSER GENERAL PUBLIC LICENSEVersion 2.1, February 1999
AP
PE
ND
IX
141
Although the Lesser General Public License is Less protective ofthe users' freedom, it does ensure that the user of a program thatis linked with the Library has the freedom and the wherewithal torun that program using a modified version of the Library.
The precise terms and conditions for copying, distribution andmodification follow. Pay close attention to the difference betweena "work based on the library" and a "work that uses the library".The former contains code derived from the library, whereas thelatter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSETERMS AND CONDITIONS FOR COPYING, DISTRIBUTIONAND MODIFICATION
0. This license agreement applies to any software library or otherprogram which contains a notice placed by the copyright hold-er or other authorized party saying it may be distributedunder the terms of this Lesser General Public License (alsocalled “this license”). Each license is addressed as "you".
A “library” means a collection of software functions and/ordata prepared so as to be conveniently linked with applicationprograms (which use some of those functions and data) toform executables.
The “Library”, below, refers to any such software library or workwhich has been distributed under these terms. A “work basedon the Library” means either the Library or any derivative workunder copyright law: that is to say, a work containing thelibrary or a portion of it, either verbatim or with modificationsand/or translated straightforwardly into another language.(Hereinafter, translation is included without limitation in theterm “modification”.)
“Source code” for a work means the preferred form of thework for making modifications to it. For a library, completesource code means all the source code for all modules it con-tains, plus any associated interface definition files, plus thescripts used to control compilation and installation of thelibrary.
Activities other than copying, distribution and modificationare not covered by this license; they are outside its scope.The act of running a program using the Library is not restrict-ed, and output from such a program is covered only if its con-tents constitute a work based on the library (independent ofthe use of the Library in a tool for writing it). Whether that istrue depends on what the library does and what the programthat uses the library does.
1. You may copy and distribute verbatim copies of the library'scomplete source code as you receive it, in any medium, pro-vided that you conspicuously and appropriately publish on
each copy an appropriate copyright notice and disclaimer ofwarranty; keep intact all the notices that refer to this licenseand to the absence of any warranty; and distribute a copy ofthis license along with the Library.
You may charge a fee for the physical act of transferring acopy, and you may at your option offer warranty protection inexchange for a fee.
2. You may modify your copy or copies of the Library or anyportion of it, thus forming a work based on the Library, andcopy and distribute such modifications or work under theterms of section 1 above, provided that you also meet all ofthese conditions:a) The modified work must itself be a software library.b) You must cause the files modified to carry prominent
notices stating that you changed the files and the date ofany change.
c) You must cause the whole of the work to be licensed at nocharge to all third parties under the terms of this license.
d) If a facility in the modified Library refers to a function or atable of data to be supplied by an application program thatuses the facility, other than as an argument passed whenthe facility is invoked, then you must make a good faitheffort to ensure that, in the event an application does notsupply such function or table, the facility still operates, andperforms whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square rootshas a purpose that is entirely well-defined independent of theapplication. Therefore, Subsection 2d requires that any appli-cation-supplied function or table used by this function must beoptional: if the application does not supply it, the square rootfunction must still compute square roots.)
These requirements apply to the modified work as a whole. Ifidentifiable sections of that work are not derived from thelibrary, and can be reasonably considered independent andseparate works in themselves, then this license, and its terms,do not apply to those sections when you distribute them asseparate works. But when you distribute the same sections aspart of a whole which is a work based on the library, the dis-tribution of the whole must be on the terms of this license,whose permissions for other licenses extend to the entirewhole, and thus to each and every part regardless of whowrote it.Thus, it is not the intent of this section to claim rights or con-test your rights to work written entirely by you; rather, theintent is to exercise the right to control the distribution ofderivative or collective works based on the library.
In addition, mere aggregation of another work not based onthe library with the library (or with a work based on thelibrary) on a volume of a storage or distribution medium doesnot bring the other work under the scope of this license.
AP
PE
ND
IX
142
APPENDIX
3. You may opt to apply the terms of the ordinary GNU GeneralPublic License instead of this License to a given copy of theLibrary. To do this, you must alter all the notices that refer tothis License, so that they refer to the ordinary GNU GeneralPublic License, version 2, instead of to this License. (If a newerversion than version 2 of the ordinary GNU General PublicLicense has appeared, then you can specify that versioninstead if you wish.) Do not make any other change in thesenotices.Once this change is made in a given copy, it is irreversible forthat copy, so the ordinary GNU General Public License appliesto all subsequent copies and derivative works made from thatcopy.This option is useful when you wish to copy part of the codeof the library into a program that is not a library.
4. You may copy and distribute the library (or a portion or deriv-ative of it, under Section 2) in object code or executable formunder the terms of Sections 1 and 2 above provided that youaccompany it with the complete corresponding machine-readable source code, which must be distributed under theterms of sections 1 and 2 above on a medium customarilyused for software interchange.If distribution of object code is made by offering access tocopy from a designated place, then offering equivalent accessto copy the source code from the same place satisfies therequirement to distribute the source code, even though thirdparties are not compelled to copy the source along with theobject code.
5. A program that contains no derivative of any portion of theLibrary, but is designed to work with the Library by beingcompiled or linked with it, is called a “work that uses theLibrary”. Such a work, in isolation, is not a derivative work ofthe Library, and therefore falls outside the scope of thislicense.
However, linking a “work that uses the library” with the Librarycreates an executable that is a derivative of the Library(because it contains portions of the library), rather than a“work that uses the library”. The executable is therefore cov-ered by this license. Section 6 states terms for distribution ofsuch executable.
When a “work that uses the library” uses material from a head-er file that is part of the library, the object code for the workmay be a derivative work of the library even though the sourcecode is not.Whether this is true is especially significant if the work can belinked without the library, or if the work is itself a library. Thethreshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, datastructure layouts and accessories, and small macros and smallinline functions (ten lines or less in length), then the use of
the object file is unrestricted, regardless of whether it is legal-ly a derivative work. (Executable containing this object codeplus portions of the library will still fall under Section 6.)
Otherwise, if the work is a derivative of the library, you maydistribute the object code for the work under the terms ofSection 6. Any executable containing that work also fall underSection 6, whether or not they are linked directly with thelibrary itself.
6. As an exception to the sections above, you may also combineor link a "work that uses the library" with the library to pro-duce a work containing portions of the library, and distributethat work under terms of your choice, provided that the termspermit modification of the work for the customer's own useand reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the workthat the library is used in it and that the Library and its useare covered by this license. You must supply a copy of thislicense. If the work during execution displays copyrightnotices, you must include the copyright notice for the libraryamong them, as well as a reference directing the user to thecopy of this license. Also, you must do one of these things:
a) Accompany the work with the complete correspondingmachine-readable source code for the library includingwhatever changes were used in the work (which must bedistributed under Sections 1 and 2 above); and, if the workis an executable linked with the Library, with the completemachine-readable “work that uses the Library”, as objectcode and/or source code, so that the user can modify thelibrary and then relink to produce a modified executablecontaining the modified library. (It is understood that theuser who changes the contents of definitions files in thelibrary will not necessarily be able to recompile the appli-cation to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with thelibrary. A suitable mechanism is one that (1) uses at run timea copy of the library already present on the user’s computersystem, rather than copying library functions into the exe-cutable, and (2) will operate properly with a modified versionof the library, if the user installs one, as long as the modifiedversion is interface-compatible with the version that thework was made with.
c) Accompany the work with a written offer, valid for at leastthree years, to give the same user the materials specified inSubsection 6, above, for a charge no more than the cost ofperforming this distribution.
d) If distribution of the work is made by offering access tocopy from a designated place, offer equivalent access tocopy the above specified materials from the same place.
e) Verify that the user has already received a copy of thesematerials or that you have already sent this user a copy.
AP
PE
ND
IX
143
For an executable, the required form of the "work that usesthe library" must include any data and utility programs need-ed for reproducing the executable from it. However, as a spe-cial exception, the materials to be distributed need notinclude anything that is normally distributed (in either sourceor binary form) with the major components (compiler, kernel,and so on) of the operating system on which the executableruns, unless that component itself accompanies the exe-cutable.
It may happen that this requirement contradicts the licenserestrictions of other proprietary libraries that do not normal-ly accompany the operating system. Such a contradictionmeans you cannot use both them and the library together inan executable that you distribute.
7. You may place library facilities that are a work based on thelibrary side-by-side in a single library together with otherlibrary facilities not covered by this license, and distributesuch a combined library, provided that the separate distribu-tion of the work based on the Library and of the other libraryfacilities is otherwise permitted, and provided that you dothese two things:
a) Accompany the combined library with a copy of the samework based on the Library, uncombined with any otherlibrary facilities. This must be distributed under the termsof the sections above.
b) Give prominent notice with the combined library of thefact that part of it is a work based on the library, andexplaining where to find the accompanying uncombinedform of the same work.
8. You may not copy, modify, sublicense, link with, or distributethe library except as expressly provided under this license.Any attempt otherwise to copy, modify, sublicense, link with,or distribute the library is void, and will automatically termi-nate your rights under this license. However, parties who havereceived copies, or rights, from you under this license will nothave their licenses terminated so long as such parties remainin full compliance.
9. You are not required to accept this license, since you have notsigned it. However, nothing else grants you permission to mod-ify or distribute the library or its derivative works. Theseactions are prohibited by law if you do not accept this license.Therefore, by modifying or distributing the library (or any workbased on the library), you indicate your acceptance of thislicense to do so, and all its terms and conditions for copying,distributing or modifying the library or works based on it.
10.Each time you redistribute the library (or any work based onthe Library), the recipient automatically receives a licensefrom the original licensor to copy, distribute, link with or mod-ify the library subject to these terms and conditions. You maynot impose any further restrictions on the recipients' exercise
of the rights granted herein.You are not responsible for enforcing compliance by thirdparties with this license.
11. If, as a consequence of a court judgment or allegation ofpatent infringement or for any other reason (not limited topatent issues), conditions are imposed on you (whether bycourt order, agreement or otherwise) that contradict the con-ditions of this license, they do not excuse you from the con-ditions of this license. If you cannot distribute so as to satis-fy simultaneously your obligations under this license and anyother pertinent obligations, then as a consequence you maynot distribute the library at all. For example, if a patent licensewould not permit royalty-free redistribution of the library byall those who receive copies directly or indirectly throughyou, then the only way you could satisfy both it and thislicense would be to refrain entirely from distribution of thelibrary.If any portion of this section is held invalid or unenforceableunder any particular circumstance, the balance of the sectionis intended to apply, and the section as a whole is intended toapply in other circumstances.It is not the purpose of this section to induce you to infringeany patents or other property right claims or to contest valid-ity of any such claims; this section has the sole purpose ofprotecting the integrity of the free software distribution sys-tem which is implemented by public license practices. Manypeople have made generous contributions to the wide rangeof software distributed through that system in reliance onconsistent application of that system; it is up to theauthor/donor to decide if he or she is willing to distributesoftware through any other system and a license cannotimpose that choice.This section is intended to make thoroughly clear what isbelieved to be a consequence of the rest of this license.
12.If the distribution and/or use of the library is restricted in cer-tain countries either by patents or by copyrighted interfaces,the original copyright holder who places the library under thislicense may add an explicit geographical distribution limitationexcluding those countries, so that distribution is permittedonly in or among countries not thus excluded. In such case,this license incorporates the limitation as if written in the bodyof this license.
13.The Free Software Foundation may publish revised and/ornew versions of the Lesser General Public License from time totime. Such new versions will be similar in spirit to the presentversion, but may differ in detail to address new problems orconcerns.Each version is given a distinguishing version number. If thelibrary specifies a version number of this license which appliesto it and “any later version”, you have the option of followingthe terms and conditions either of that version or of any laterversion published by the Free Software Foundation.
AP
PE
ND
IX
144
APPENDIX
If the library does not specify a license version number, youmay choose any version ever published by the Free SoftwareFoundation.
14.If you wish to incorporate parts of the library into other freeprograms whose distribution conditions are incompatible withthese, write to the author to ask for permission. For softwarewhich is copyrighted by the Free Software Foundation, writeto the Free Software Foundation; we sometimes make excep-tions for this. Our decision will be guided by the two goals ofpreserving the free status of all derivatives of our free softwareand of promoting the sharing and reuse of software generally.
NO WARRANTY
15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,THERE IS NO WARRANTY FOR THE LIBRARY, TO THEEXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHENOTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "ASIS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITEDTO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRERISK AS TO THE QUALITY AND PERFORMANCE OF THELIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVEDEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARYSERVICING, REPAIR OR CORRECTION.
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW ORAGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/ORREDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BELIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGESARISING OUT OF THE USE OR INABILITY TO USE THELIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATAOR DATA BEING RENDERED INACCURATE OR LOSSES SUS-TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THELIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEENADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new libraries
If you develop a new library, and you want it to be of the great-est possible use to the public, we recommend making it free soft-ware that everyone can redistribute and change. You can do soby permitting redistribution under these terms (or, alternatively,under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library.It is safest to attach them to the start of each source file to mosteffectively convey the exclusion of warranty; and each file shouldhave at least the “copyright” line and a pointer to where the fullnotice is found.
one line to give the library's name and a brief idea of what it does.Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modifyit under the terms of the GNU Lesser General Public License aspublished by the Free Software Foundation; either version 2.1 ofthe license, or (at your option) any later version.
This library is distributed in the hope that it will be useful, butWITHOUT ANY WARRANTY; without even the implied warrantyof MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-POSE. See the GNU Lesser General Public License for moredetails.
You should have received a copy of the GNU Lesser GeneralPublic License along with this library; if not, write to the FreeSoftware Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,MA 02110-1301 USA
Also add information on how to contact you by electronic andpaper mail.
You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for thelibrary, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in thelibrary ‘Frob’ (a library for tweaking knobs) written by JamesRandom Hacker.
signature of Ty Coon, 1 April 1990Ty Coon, President of Vice
AP
PE
ND
IX
145
1.Definitions.
1.0.1. “Commercial use” means distribution or otherwise makingthe covered code available to a third party.
1.1. “Contributor” means each entity that creates or con-tributes to the creation of modifications.
1.2. “Contributor version” means the combination of the orig-inal code, prior modifications used by a contributor, andthe modifications made by that particular contributor.
1.3. “Covered code” means the original code or modificationsor the combination of the original code and modifications,in each case including portions thereof.
1.4. “Electronic distribution mechanism” means a mechanismgenerally accepted in the software development communi-ty for the electronic transfer of data.
1.5. “Executable” means covered code in any form other thansource code.
1.6. “Initial developer” means the individual or entity identifiedas the initial Developer in the Source Code notice requiredby exhibit A.
1.7. “Larger work” means a work which combines covered codeor portions thereof with code not governed by the termsof this License.
1.8. “License” means this document.
1.8.1. “Licensable” means having the right to grant, to the maxi-mum extent possible, whether at the time of the initialgrant or subsequently acquired, any and all of the rightsconveyed herein.
1.9. “Modifications” means any addition to or deletion fromthe substance or structure of either the original code orany previous modifications. When covered code isreleased as a series of files, a modification is:
A. Any addition to or deletion from the contents of a filecontaining original code or previous modifications.
B. Any new file that contains any part of the original codeor previous modifications.
1.10. “Original code” means source code of computer software
code which is described in the source code noticerequired by exhibit as original code, and which, at the timeof its release under this license is not already coveredcode governed by this license.
1.10.1.“Patent claims” means any patent claim(s), now owned orhereafter acquired, including without limitation, method,process, and apparatus claims, in any patent licensable bygrantor.
1.11. “Source code” means the preferred form of the coveredcode for making modifications to it, including all modulesit contains, plus any associated interface definition files,scripts used to control compilation and installation of anexecutable, or source code differential comparisonsagainst either the original code or another well known,available covered code of the contributor's choice. Thesource code can be in a compressed or archival form, pro-vided the appropriate decompression or de-archiving soft-ware is widely available for no charge.
1.12. “You” (or “Your”) means an individual or a legal entityexercising rights under, and complying with all of the termsof, this license or a future version of this license issuedunder section 6.1.For legal entities, “You” includes any entity which controls,is controlled by, or is under common control with You. Forpurposes of this definition, “control” means (a) the power,direct or indirect, to cause the direction or management ofsuch entity, whether by contract or otherwise, or (b) own-ership of more than fifty percent (50%) of the outstand-ing shares or beneficial ownership of such entity.
2. Source Code License.
2.1. The initial developer grant.The initial developer hereby grants You a world-wide, roy-alty-free, non-exclusive license, subject to third party intel-lectual property claims:
a) under intellectual property rights (other than patent ortrademark) licensable by initial developer to use, repro-duce, modify, display, perform, sublicense and distrib-ute the original code (or portions thereof) with or with-out modifications, and/or as part of a larger work; and
(b) under patents claims infringed by the making, using orselling of original code, to make, have made, use, prac-tice, sell, and offer for sale, and/or otherwise disposeof the original code (or portions there of).
MOZILLA PUBLIC LICENSEVersion 1.1
---------------
AP
PE
ND
IX
146
APPENDIX
(c) the licenses granted in this section 2.1(a) and (b) areeffective on the date Initial developer first distributesoriginal code under the terms of this license.
(d) Notwithstanding section 2.1(b) above, no patentlicense is granted: 1) for code that You delete from theoriginal Code; 2) separate from the original code; or3) for infringements caused by: i) the modification ofthe original code or ii) the combination of the originalcode with other software or devices.
2.2. Contributor Grant.Subject to third party intellectual property claims, eachcontributor hereby grants You a world-wide, royalty-free,non-exclusive license
(a) under intellectual property rights (other than patentor trademark) licensable by contributor, to use,reproduce, modify, display, perform, sublicense anddistribute the modifications created by such contribu-tor (or portions thereof) either on an unmodifiedbasis, with other modifications, as covered codeand/or as part of a larger work; and
(b) under patent claims infringed by the making, using, orselling of modifications made by that contributoreither alone and/or in combination with its contributorversion (or portions of such combination), to make,use, sell, offer for sale, have made, and/or otherwisedispose of: 1) modifications made by that contributor(or portions thereof); and 2) the combination of mod-ifications made by that contributor with its contributorversion (or portions of such combination).
(c) the licenses granted in sections 2.2(a) and 2.2(b) areeffective on the date contributor first makes commer-cial use of the covered code.
(d) Notwithstanding section 2.2(b) above, no patentlicense is granted: 1) for any code that contributor hasdeleted from the contributor version; 2) separate fromthe contributor version; 3) for infringements causedby: i) third party modifications of contributor versionor ii) the combination of modifications made by thatcontributor with other software (except as part of thecontributor version) or other devices; or 4) underpatent claims infringed by covered code in theabsence of modifications made by that contributor.
3. Distribution Obligations.
3.1. Application of license.The modifications which You create or to which you con-tribute are governed by the terms of this license, includingwithout limitation section 2.2. The source code version ofcovered code may be distributed only under the terms ofthis license or a future version of this license releasedunder section 6.1, and you must include a copy of thislicense with every copy of the source code you distribute.
You may not offer or impose any terms on any source codeversion that alters or restricts the applicable version ofthis license or the recipients' rights hereunder. However,you may include an additional document offering theadditional rights described in section 3.5.
3.2. Availability of source code.Any modification which you create or to which you con-tribute must be made available in source code form underthe terms of this license either on the same media as anexecutable version or via an accepted electronic distribu-tion mechanism to anyone to whom you made an exe-cutable version available; and if made available via elec-tronic distribution mechanism, must remain available for atleast twelve (12) months after the date it initially becameavailable, or at least six (6) months after a subsequentversion of that particular modification has been madeavailable to such recipients. You are responsible for ensur-ing that the source code version remains available even ifthe electronic distribution mechanism is maintained by athird party.
3.3. Description of modifications.You must cause all covered code to which you contribute tocontain a file documenting the changes You made to createthat covered code and the date of any change. You mustinclude a prominent statement that the modification isderived, directly or indirectly, from original code provided bythe initial developer and including the name of the initialdeveloper in (a) the source code, and (b) in any notice in anexecutable version or related documentation in which youdescribe the origin or ownership of the covered code.
3.4. Intellectual property matters(a) Third party claims.If contributor has knowledge that a license under a thirdparty's intellectual property rights is required to exercisethe rights granted by such contributor under sections 2.1or 2.2, contributor must include a text file with the sourcecode distribution titled "LEGAL" which describes the claimand the party making the claim in sufficient detail that arecipient will know whom to contact. If contributor obtainssuch knowledge after the modification is made available asdescribed in section 3.2, contributor shall promptly modi-fy the LEGAL file in all copies contributor makes availablethereafter and shall take other steps (such as notifyingappropriate mailing lists or newsgroups) reasonably calcu-lated to inform those who received the covered code thatnew knowledge has been obtained.(b) Contributor APIs.If contributor's modifications include an applicationprogramming interface and contributor has knowledge ofpatent licenses which are reasonably necessary to implementthat API, contributor must also include this information inthe LEGAL file.
AP
PE
ND
IX
147
(c) Representations.contributor represents that, except as disclosed pursuantto section 3.4(a) above, contributor believes that contributor'smodifications are contributor's original creation(s)and/or contributor has sufficient rights to grant the rightsconveyed by this license.
3.5. Required notices.You must duplicate the notice in exhibit A in each file ofthe source code. If it is not possible to put such notice ina particular source code file due to its structure, then Youmust include such notice in a location (such as a relevantdirectory) where a user would be likely to look for such anotice. If You created one or more modification(s), youmay add your name as a contributor to the noticedescribed in exhibit A. you must also duplicate this licensein any documentation for the source code where Youdescribe recipients' rights or ownership rights relating tocovered code. You may choose to offer, and to charge afee for, warranty, support, indemnity or liability obligationsto one or more recipients of covered code. However, youmay do so only on your own behalf, and not on behalf ofthe Initial developer or any contributor. You must make itabsolutely clear than any such warranty, support, indemni-ty or liability obligation is offered by you alone, and Youhereby agree to indemnify the Initial developer and everycontributor for any liability incurred by the Initial develop-er or such contributor as a result of warranty, support,indemnity or liability terms you offer.
3.6. Distribution of executable versions.You may distribute covered code in executable form only ifthe requirements of section 3.1-3.5 have been met forthat covered code, and if you include a notice stating thatthe source code version of the covered code is availableunder the terms of this license, including a description ofhow and where you have fulfilled the obligations of section3.2. The notice must be conspicuously included in anynotice in an executable version, related documentation orcollateral in which you describe recipients' rights relatingto the covered code. You may distribute the executableversion of covered code or ownership rights under alicense of your choice, which may contain terms differentfrom this license, provided that you are in compliance withthe terms of this license and that the license for the exe-cutable version does not attempt to limit or alter the recip-ient's rights in the source code version from the rights setforth in this license. If you distribute the executable ver-sion under a different license you must make it absolutelyclear that any terms which differ from this license areoffered by you alone, not by the Initial developer or anycontributor. You hereby agree to indemnify the initialdeveloper and every contributor for any liability incurredby the initial developer or such contributor as a result ofany such terms You offer.
3.7. Larger works.You may create a larger work by combining covered codewith other code not governed by the terms of this licenseand distribute the larger work as a single product. In sucha case, you must make sure the requirements of thislicense are fulfilled for the covered code.
4. Inability to comply due to statute or regulation.If it is impossible for you to comply with any of the termsof this license with respect to some or all of the coveredcode due to statute, judicial order, or regulation then youmust: (a) comply with the terms of this license to the max-imum extent possible; and (b) describe the limitations andthe code they affect. Such description must be included inthe LEGAL file described in section 3.4 and must beincluded with all distributions of the source code. Exceptto the extent prohibited by statute or regulation, suchdescription must be sufficiently detailed for a recipient ofordinary skill to be able to understand it.
5. Application of this license.This license applies to code to which the initial developer hasattached the notice in exhibit A and to related covered code.
6. Versions of the license.
6.1. New versions.Netscape communications corporation (“Netscape”) maypublish revised and/or new versions of the license fromtime to time. Each version will be given a distinguishingversion number.
6.2. Effect of new versions.Once covered code has been published under a particularversion of the license, you may always continue to use itunder the terms of that version. You may also choose touse such covered code under the terms of any subsequentversion of the license published by netscape. No oneother than netscape has the right to modify the termsapplicable to covered code created under this license.
6.3. Derivative works.If You create or use a modified version of this license(which you may only do in order to apply it to code whichis not already covered code governed by this license), Youmust (a) rename Your license so that the phrases"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL","NPL" or any confusingly similar phrase do not appear inyour license (except to note that your license differs fromthis license) and (b) otherwise make it clear that Yourversion of the license contains terms which differ from theMozilla Public license and netscape Public License. (Fillingin the name of the initial developer, original code or con-tributor in the notice described in exhibit A shall not ofthemselves be deemed to be modifications of this license.)
AP
PE
ND
IX
148
APPENDIX
7. DISCLAIMER OF WARRANTY.COVERED CODE IS PROVIDED UNDER THIS LICENSEON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANYKIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,WITHOUT LIMITATION, WARRANTIES THAT THE COV-ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FITFOR A PARTICULAR PURPOSE OR NON-INFRINGING.THE ENTIRE RISK AS TO THE QUALITY AND PERFOR-MANCE OF THE COVERED CODE IS WITH YOU.SHOULD ANY COVERED CODE PROVE DEFECTIVE INANY RESPECT, YOU (NOT THE INITIAL DEVELOPER ORANY OTHER CONTRIBUTOR) ASSUME THE COST OFANY NECESSARY SERVICING, REPAIR OR CORRECTION.THIS DISCLAIMER OF WARRANTY CONSTITUTES ANESSENTIAL PART OF THIS LICENSE. NO USE OF ANYCOVERED CODE IS AUTHORIZED HEREUNDER EXCEPTUNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This license and the rights granted hereunder will terminateautomatically if you fail to comply with terms herein andfail to cure such breach within 30 days of becoming awareof the breach. All sublicenses to the covered code whichare properly granted shall survive any termination of thislicense. Provisions which, by their nature, must remain ineffect beyond the termination of this license shall survive.
8.2. If you initiate litigation by asserting a patent infringementclaim (excluding declatory judgment actions) against ini-tial developer or a contributor (the initial developer orcontributor against whom you file such action is referredto as “Participant”) alleging that:
(a) such participant's contributor version directly or indi-rectly infringes any patent, then any and all rightsgranted by such participant to you under sections 2.1and/or 2.2 of this license shall, upon 60 days noticefrom Participant terminate prospectively, unless if within60 days after receipt of notice you either: (i) agree inwriting to pay participant a mutually agreeable reasonableroyalty for your past and future use of modificationsmade by such participant, or (ii) withdraw your litigationclaim with respect to the contributor version againstsuch participant. If within 60 days of notice, a reasonableroyalty and payment arrangement are not mutuallyagreed upon in writing by the parties or the litigationclaim is not withdrawn, the rights granted by partici-pant to you under sections 2.1 and/or 2.2 automati-cally terminate at the expiration of the 60 day noticeperiod specified above.
(b) any software, hardware, or device, other than such par-ticipant's contributor Version, directly or indirectlyinfringes any patent, then any rights granted to You by
such participant under sections 2.1(b) and 2.2(b) arerevoked effective as of the date you first made, used,sold, distributed, or had made, modifications made bythat participant.
8.3. If you assert a patent infringement claim against partici-pant alleging that such participant's contributor versiondirectly or indirectly infringes any patent where such claimis resolved (such as by license or settlement) prior to theinitiation of patent infringement litigation, then the rea-sonable value of the licenses granted by such participantunder sections 2.1 or 2.2 shall be taken into account indetermining the amount or value of any payment orlicense.
8.4. In the event of termination under sections 8.1 or 8.2above, all end user license agreements (excluding distributorsand resellers) which have been validly granted by you orany distributor hereunder prior to termination shall survivetermination.
9. LIMITATION OF LIABILITY.UNDER NO CIRCUMSTANCES AND UNDER NO LEGALTHEORY, WHETHER TORT (INCLUDING NEGLIGENCE),CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIALDEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS-TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OFANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FORANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN-TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH-OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC-TION, OR ANY AND ALL OTHER COMMERCIAL DAM-AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVEBEEN INFORMED OF THE POSSIBILITY OF SUCH DAM-AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLYTO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT-ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENTAPPLICABLE LAW PROHIBITS SUCH LIMITATION. SOMEJURISDICTIONS DO NOT ALLOW THE EXCLUSION ORLIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-AGES, SO THIS EXCLUSION AND LIMITATION MAY NOTAPPLY TO YOU.
10. U.S. GOVERNMENT END USERS.The covered code is a "commercial item," as that term isdefined in 48 C.F.R. 2.101 (Oct. 1995), consisting of"commercial computer software" and "commercial computersoftware documentation," as such terms are used in 48C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4(June 1995), all U.S. Government end users acquire cov-ered code with only those rights set forth herein.
AP
PE
ND
IX
149
11. MISCELLANEOUS.This license represents the complete agreement concerningsubject matter hereof. If any provision of this license isheld to be unenforceable, such provision shall be reformedonly to the extent necessary to make it enforceable. ThisLicense shall be governed by California law provisions(except to the extent applicable law, if any, provides oth-erwise), excluding its conflict-of-law provisions. Withrespect to disputes in which at least one party is a citizenof, or an entity chartered or registered to do business inthe united states of america, any litigation relating to thisLicense shall be subject to the jurisdiction of the federalcourts of the northern district of california, with venuelying in santa clara county, california, with the losing partyresponsible for costs, including without limitation, courtcosts and reasonable attorneys' fees and expenses. Theapplication of the united nations convention on contractsfor the International sale of goods is expressly excluded.Any law or regulation which provides that the language ofa contract shall be construed against the drafter shall notapply to this license.
12. RESPONSIBILITY FOR CLAIMS.As between initial developer and the contributors, eachparty is responsible for claims and damages arising, directlyor indirectly, out of its utilization of rights under thislicense and you agree to work with initial developer andcontributors to distribute such responsibility on an equitablebasis. Nothing herein is intended or shall be deemed toconstitute any admission of liability.
13. MULTIPLE-LICENSED CODE.Initial developer may designate portions of the coveredcode as "Multiple-Licensed". "Multiple-Licensed" meansthat the initial developer permits you to utilize portions ofthe covered code under your choice of the NPL or thealternative licenses, if any, specified by the initial developerin the file described in exhibit A.
EXHIBIT A -Mozilla Public License.
The contents of this file are subject to the Mozilla Public LicenseVersion 1.1 (the “license”); you may not use this file except incompliance with the License. You may obtain a copy of thelicense at http://www.mozilla.org/MPL/
Software distributed under the license is distributed on an "ASIS" basis, WITHOUT WARRANTY OF ANY KIND, either expressor implied. See the license for the specific language governingrights and limitations under the License.
The Original Code is ______________________________________.
The Initial Developer of the Original Codeis___________________.Portions created by ______________________ are Copyright (C)_______________________. All Rights Reserved.
Alternatively, the contents of this file may be used under theterms of the _____ license (the "[___] License"), in which casethe provisions of [______] license are applicable instead of thoseabove. If you wish to allow use of your version of this file onlyunder the terms of the [____] license and not to allow others touse your version of this file under the MPL, indicate your decisionby deleting the provisions above and replace them with thenotice and other provisions required by the [___] license. If youdo not delete the provisions above, a recipient may use your versionof this file under either the MPL or the [___] license."
NOTE: The text of this exhibit A may differ slightly from the textof the notices in the source code files of the original code. Youshould use the text of this exhibit A rather than the text found inthe original code/source code for Your modifications.