-
Please read this manual carefully before operating your set.
Retain it for future reference.Record model number and serial
number of the set. See the label attached on the back cover and
quote this information to your dealer when you require service.
ENERGYSTAR is a set of power-savingguidelines issued by the
U.S.Environmental Protection Agency(EPA).
As an ENERGY STARPartner LGE U. S. A.,Inc.has determined that
thisproduct meets the ENER-GY STAR guidelines forenergy
efficiency.
P/NO : 38289U0527B (0607-REV07)Printed in Korea
OWNER’S MANUAL
LCD TVMODELS: 32LC2D
32LC2DC37LC2D42LC2D
PLASMA TVMODELS: 42PC3D 42PC1DVH
42PC3DC 42PC3DH42PC3DV 42PC3DVA50PC3D 50PC3DH50PC3DX
Internet Home Page :
http://www.lge.comhttp://www.lg.cahttp://www.lgcommercial.com
-
2
Warning
WARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user tothe presence of
uninsulated “dangerous voltage” within the product’s enclosure that
may be of suffi-cient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence ofimportant operating and
maintenance (servicing) instructions in the literature accompanying
the appli-ance.
NOTE TO CABLE/TV INSTALLER:This reminder is provided to call the
CATV system installer’s attention to Article 820-40 of the National
ElectricCode (U.S.A.). The code provides guidelines for proper
grounding and, in particular, specifies that the cableground shall
be connected to the grounding system of the building, as close to
the point of the cable entry as prac-tical.
REGULATORY INFORMATIONThis equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to
Part15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference ina residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if notinstalled and used in accordance with
the instructions, may cause harmful interference to radio
communications.However, there is no guarantee that interference
will not occur in a particular installation. If this equipment
doescause harmful interference to radio or television reception,
which can be determined by turning the equipment offand on, the
user is encouraged to try to correct the interference by one or
more of the following measures:- Reorient or relocate the receiving
antenna.- Increase the separation between the equipment and
receiver.- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.- Consult
the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party
responsible for compliance could void theuser’s authority to
operate the equipment.
CAUTION:Do not attempt to modify this product in any way without
written authorization from LG Electronics Corporation.Unauthorized
modification could void the user’s authority to operate this
product.
U.S.A. only
-----------------------------------------------COMPLIANCE:
The responsible party for this product’s compliance is:LG
Electronics U.S.A., Inc.1000 Sylvan Avenue, Englewood Cliffs, NJ
07632Phone: 1-800-243-0000http://www.lgusa.com
---------------------------------------------------------------
CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPEN
WWarningarning
-
3
Safety Instructions
WARNING :To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on
theapparatus.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install
inaccordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,heat
registers, stoves, or other apparatus (includingamplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized orgrounding
type plug. A polarized plug has two bladeswith one wider than the
other. A grounding type plug hastwo blades and a third grounding
prong. The wide bladeor the third prong is provided for your
safety. When theprovided plug does not fit into your outlet,
consult anelectrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on orpinched
particularly at plugs, convenience recepta-cles, and the point
where they exit from the apparatus.
11. Only use the attachments / accessories specified bythe
manufacturer.
Safety InstructionsSafety Instructions
Owner's Manual
-
4
Safety Instructions
12. Use only with a cart, stand, tripod, bracket, or
tablespecified by the manufacturer, or sold with the appa-ratus.
When a cart is used, use caution when movingthe cart / apparatus
combination to avoid injury fromtip-over.
13. Unplug this apparatus during lightning storms or whenunused
for long periods of time.
14. Refer all servicing to qualified service personnel.Servicing
is required when the apparatus has beendamaged in any way, such as
power supply cord orplug is damaged, liquid has been spilled or
objectshave fallen into the apparatus, the apparatus has
beenexposed to rain or moisture, does not operate normal-ly, or has
been dropped.
15. DISCONNECTING DEVICE FROM MAINS
- Mains plug is the disconnecting device. The plugmust remain
readily operable.
On Disposal
a. The fluorescent lamp used in this product contains a small
amount of mercury.b. Do not dispose of this product with general
household waste.
Disposal of this product must be carried out in accordance to
the regulations of your local authority.
Note
- If the TV feels cold to the touch, there may be a small
“flicker” when when it is turned on. This is normal, there is
noth-ing wrong with TV.
- Some minute dot defects may be visible on the screen,
appearing as tiny red, green, or blue spots. However, they haveno
adverse effect on the monitor's performance.
- Avoid touching the LCD screen or holding your finger(s)
against it for long periods of time. Doing so may produce
sometemporary distortion effects on the screen.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated
circuit; that is, a single outlet circuit which powers only
thatappliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets, loose or
damaged wall outlets, extension cords, frayed power cords,or
damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire.Periodically
examine the cord of your appliance, and if its appearance indicates
damage or deterioration, unplug it, discon-tinue use of the
appliance, and have the cord replaced with an exact replacement
part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such
as being twisted, kinked, pinched, closed in a door, orwalked upon.
Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance.
For LCD TV
-
5
Contents
ContentsContents
Intr
oduc
tion
Inst
alla
tio
nO
per
atio
n
32 Turning on the TV32 Volume Adjustment32 Channel Selection32
On Screen Menus Language Selection33 On Screen Menus Selection and
Adjustment
34 EZ Scan (Channel Search)34 Manual Scan35 Channel Edit36 DTV
Signal Strength36 Input Source37 Input Label
38 EZ Picture38 APM (Adaptive Picture Mode)39 Manual Picture
Control (EZ Picture-Custom option)39 Color Temperature Control39
Video Reset
40 Audio Language40 EZ SoundRite41 EZ Sound41 Manual Sound
Control (EZ Sound-Custom option)42 Stereo/SAP Broadcasts Setup42
Front Surround43 TV Speakers On/Off Setup43 BBE
2 Warnings
3~4 Safety Instructions
7 Accessories
8 Controls (Model Name: 32/37/42LC2D**)
8 Swivel Stand (42LC2D** only)
9 Connection Options (Model Name: 32/37/42LC2D**)
10 Controls (Model Name: 42PC1D**/42PC3D**/50PC3D**)
11 Connection Options (Model Name:
42PC1D**/42PC3D**/50PC3D**)
12~16 Remote Control Key Functions
17 Various Installation18~20 Basic Connection
21 Antenna or Cable Connection22~23 VCR Setup23 External AV
Source Setup24~25 DVD Setup26~27 HDSTB Setup28 Monitor Out Setup28
Digital Audio Output29~31 PC Setup
Setup MenuOptions
Video MenuOptions
Audio MenuOptions
Basic operation
ExternalEquipment
Connections
-
6
ContentsR
efer
ence
44 Auto Clock Setup44 Manual Clock Setup45 On/Off Timer Setup45
Sleep Timer46 Auto Off
47 Aspect Ratio Control48 Cinema 3:2 Mode Setup48 Caption49
Caption/Text50 Caption Option50 Low Power
(42PC1D**/42PC3D**/50PC3D** only)51 ISM (Image Sticking
Minimization) Method (42PC1D**/42PC3D**/50PC3D** only)
52~53 Parental Lock Setup
54~59 External Control Device Setup
60~61 IR Codes
62 Programming the Remote
63~64 Programming Codes
65~66 Troubleshooting Checklist
66 Maintenance
67~68 Product Specifications
Option MenuFeatures
Lock Menu Options
Op
erat
ion
Time MenuOptions
-
7
Introduction
AccessoriesAccessories
IntroductionIntroduction
Owner’s Manual75Ω Round CablePower Cord
Ensure that the following accessories are included with your TV.
If any accessory is missing, please contact thedealer where you
purchased the product.User must use the shield signal interface
cable (D-sub 15 pin cable) with ferrite cores to maintain the
standardcompliance for the product.
1.5V1.5VVOL
FLASHBK
CH
1
2
3
4
5
6
7
8
09
APM
ADJUST
SAP
EZ SOUND
EZ PIC
FREEZE
A
DAY -
GUIDE
MENU
MUTE PAGE
PAGE
FAV
EXITTIM
ER
CC
INFO
ENTER
VOL
CH
POWER
1
2
3
4
5
6
7
8
09
MENU
MUTE
FAV
DAY -
GUIDE
DAY+
RATIO
VCR
TV
DVD
ENTER
APM
ADJUST
SAP
EZ SOUND
EZ PIC
FREEZE
FLASHBK
PAGE
PAGE
EXITTIM
ER
CC
INFO
AUDIO
CABLE
STB
MODE
TV INPUT
INPUT
Remote Control /Batteries
2-eye-bolts2-TV brackets
2-Wall brackets
2-TV Bracket Bolts
For 32/37/42LC2D**For 42PC1D**, 42PC3D**, 50PC3D**
Carefully place the product screen side down on acushioned
surface that will protect product andscreen from damage.
1
Place the hook of the stand in the back of theproduct as
shown.
2
Install the 4 bolts provided securely, in the back of
theproduct.
3
Stand Installation for 32LC2D**
Twister HolderArrange the wires
with the twister holder.
4-bolts for standassembly
See below for detailinformation.
32LC2D** only42LC2D** only
CableManagement
(Refer p.18)
Polishing ClothPolish the TV with
the cloth.
42PC1D**, 42PC3D** only
2-Wall brackets
2-bolts(Refer p.19)
Polishing Cloth
- Slightly wipe stained spot on the exterior onlywith the
cleansing cloths for the product exteriorif there is stain or
fingerprint on surface of theexterior.
- Do not wipe roughly when removing stain.Please be cautious of
that excessive power maycause scratch or discoloration.
D-sub 15 pin Cable
Option Extras
-
8
Introduction
Controls Controls (Model Name: 32/37/42LC2D**) (Model Name:
32/37/42LC2D**)
- This is a simplified representation of front panel. - This
picture shown below may be somewhat different from your TV.
R
CHCH
VOLVOL
ENTERENTER
MENUMENU
INPUTINPUT
CHANNEL (D, E)Buttons
VOLUME (F,G)Buttons
ENTER Button
MENU Button
INPUT Button
(Power) Button
Remote Control Sensor
Power/Standby Indicator• illuminates red in standby mode.•
illuminates green when the set is
switched on.
- The TV can be conveniently swivelled on its stand 30°to the
left or right to provide the optimum viewing angle.
Swivel Stand (42LC2D** only)
R
30° 30°
-
9
Introduction
Connection Options (Model Name: 32/37/42LC2D**)Connection
Options (Model Name: 32/37/42LC2D**)
AC IN AV IN 2AV IN 2
L/L/MONOMONO
R
AUDIOAUDIO
S-VIDEOS-VIDEO
VIDEOVIDEO
AC IN
L/L/M
ONO
MO
NOR
AU
DIO
AU
DIO
S-VI
DEO
S-VI
DEO
VID
EO
VID
EO
AV IN 2AV IN 2
HDMI/DVI INHDMI/DVI IN DIGITAL AUDIO DIGITAL AUDIO OUTOUT
OPTICALPTICAL
RS-232C INRS-232C IN(CONTROL(CONTROL & SERVICE)SERVICE)
VIDEOVIDEO AUDIOAUDIOMONO( )
VIDEOVIDEO AUDIOAUDIO
COMPONENT INCOMPONENT INS-VIDEOS-VIDEO
AV IN 1AV IN 1
AV OUTAV OUT
ANTENNAANTENNAININ
CABLECABLEININ
RGB (PCRGB (PC/DTV)DTV)
RGB INRGB IN
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
REMOTEREMOTECONTROL INCONTROL IN
AUDIO Input
S-VIDEO Input
37/42LC2D** 32LC2D**
VIDEO Input
DIGITAL AUDIO OUTOPTICAL
AV OUT
AV IN1
COMPONENT IN 1/2
HDMI / DVI IN
ANTENNA IN
CABLE IN
AUDIO (RGB/DVI)
RGB (PC/DTV)
AC IN
RS-232C INPUT(Control &Service)
REMOTE CONTROL Port
- Here shown may be somewhat different from your TV.
-
10
Introduction
Controls Controls (Model Name: 42PC1D**/42PC3D**/50PC3D**)(Model
Name: 42PC1D**/42PC3D**/50PC3D**)
- This is a simplified representation of front panel. - This
picture shown below may be somewhat different from your TV.
CH
VOL
ENTER
MENU
INPUT
CHVOLENTERMENUINPUT
CHANNEL (D, E)Buttons
VOLUME (F,G)Buttons
MENU Button
ENTER ButtonINPUT Button
(Power) Button
Power/Standby Indicator• illuminates red in standby
mode.• illuminates green when the set
is switched on.
CHANNEL (D, E)Buttons
VOLUME (F,G)Buttons
ENTER Button
MENU Button
INPUT Button
Remote Control Sensor
Power/Standby Indicator• illuminates red in standby mode.•
illuminates green when the set is switched on.
(Power) Button
42PC1D**
42PC3D**/50PC3D**
-
11
Introduction
Connection Options Connection Options (Model Name:
42PC1D**/42PC3D**/50PC3D**)(Model Name:
42PC1D**/42PC3D**/50PC3D**)
AV IN 2AV IN 2
L/L/MONOMONO
R
AUDIOAUDIO
S-VIDEOS-VIDEO
VIDEOVIDEO
HDMI/DVI INHDMI/DVI IN DIGITAL AUDIO DIGITAL AUDIO OUTOUT
OPTICALPTICAL
RS-232C INRS-232C IN(CONTROL(CONTROL & SERVICE)SERVICE)
RGB (PCRGB (PC/DTV)DTV)
RGB INRGB IN
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
VIDEOVIDEO AUDIOAUDIOMONO( )
VIDEOVIDEO AUDIOAUDIO
COMPONENT INCOMPONENT INS-VIDEOS-VIDEO
AV IN 1AV IN 1
AV OUTAV OUT
ANTENNAANTENNAININ
CABLECABLEININ AC IN
REMOTEREMOTECONTROL INCONTROL IN
- Here shown may be somewhat different from your TV.
AUDIO Input
S-VIDEO Input
VIDEO Input
DIGITAL AUDIO OUTOPTICAL
AV OUT
AV IN1
COMPONENT IN 1/2
HDMI/DVI IN
ANTENNA IN
CABLE IN
AUDIO (RGB/DVI)
RGB (PC/DTV)
AC IN
RS-232C INPUT(Control &Service)
REMOTE CONTROL Port
-
12
Introduction
Remote Control Key FunctionsRemote Control Key Functions
POWERTurns your TV or any other programmed equipment on oroff,
depending on mode.
VOL CH
POWER
1 2 3
4 5 6
7 8
0
9
MENU
MUTE FAV
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
PAGE
PAGE
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
TV INPUTRotates the input mode between Antenna and Cable. In
AV1-2, Component 1-2, RGB-DTV (or RGB-PC), and HDMI/DVIinput
sources, screen returns to the last TV channel.
MODESelects the remote operating mode: TV, DVD, VCR,
AUDIO,CABLE, or STB. Select a mode other than TV, for the remoteto
operate an external device.
INPUT (Refer to p.14)External input modes rotate in regular
sequence: Antenna,Cable, AV1-2, Component 1-2, RGB-DTV (or
RGB-PC),HDMI/DVI). (AV1, AV2,Component 1-2 input sources are
linkedautomatically, Only if these are connected)
EXITClears all on-screen displays and returns to TV viewing
fromany menu.
TIMER (Refer to p.45)Lets you select the amount of time before
your TV turnsitself off automatically.
CC (Refer to p.49)Select a closed caption: Off, CC1~4,
Text1~4.
MENUBrings up the main menu to the screen.
GUIDE (Refer to p.16)Shows program schedule.
RATIO (Refer to p.47)Changes the aspect ratio.
THUMBSTICK (Up/Down/Left/Right/ENTER)Allows you to navigate the
on-screen menus and adjust thesystem settings to your
preference.
INFO (Refer to p.15)When you watch the TV, information displays
on top of thescreen. Not available in Component 1-2, RGB and
HDMI/DVImode.
-
13
Introduction
EZ PIC (Refer to p.38)Selects a factory preset picture mode
depending on the view-ing environment.
EZ SOUND (Refer to p.41)Selects the sound appropriate for the
program's character.
SAP (Refer to p.42)Selects MTS sound: Mono, Stereo, and SAP in
analog mode. Change the audio language in DTV mode.
FREEZEFreezes the currently-viewed picture.
ADJUST (Refer to p.31)Adjusts screen position, size, and phase
in PC mode.
APM (Refer to p.38)Concurrently, compare with the Daylight,
Normal, Night Timeand Custom on the screen.
FAVUse to scroll the Favorite channels.
MUTESwitches the sound on or off.
CHANNEL UP/DOWNSelects available channels found with EZ scan and
Manual scan.
PAGE UP/DOWNMoves from one full set of screen information to the
next one.
VOLUME UP/DOWNIncreases/decreases the sound level.
VOL CH
POWER
1 2 3
4 5 6
7 8
0
9
MENU
MUTE FAV
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
PAGE
PAGE
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
— (DASH)Used to enter a program number for multiple program
chan-nels such as 2-1, 2-2,etc.
NUMBER BUTTONS
FLASHBKReturns to the last channel viewed.
VCR/DVD/DVHS/Camcorder BUTTONSControl some video cassette
recorders or DVD players("RECORD" button is not available for DVD
player).
DAY + / DAY- Moves forward or backward in 24 hour
increments.
-
14
Introduction
VOL CH
POWER
1 2 3
4 5 6
7 8
0
9
MENU
MUTE FAV
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
PAGE
PAGE
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
1. When every external equipment is connected:
2. When no external equipment is connected:
Auto LinkAuto Link
Antenna AV1 AV2Cable Component1
HDMI/DVI Component2RGB-DTV (or RGB-PC)
3. When some External Equipment is connected:(ex: When connected
to AV IN1)
RGB-DTV (or RGB-PC)
AV1
HDMI/DVI
Antenna Cable
Antenna Cable RGB-DTV (or RGB-PC) HDMI/DVI
• You can also select Input Source in the SETUP menu.
• Antenna: Select it when watching the TV/DTV.• Cable: Select it
when watching the CATV/CADTV.• AV1, AV2: Select it when watching
the VCR or external equip-
ment.• Component 1-2: Select it when using a DVD or Digital
set-top
box depend on connector.• RGB-PC / RGB-DTV: Select it when using
PC or Digital set-top
box depend on connector.• HDMI / DVI: Select it when using DVD,
PC or Digital set-top
box depend on connector.
INPUT
PreviousMENU
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source GInput Label
Set ID
Antenna
Cable
AV1
AV2
Component1
Component2
RGB-PC
HDMI/DVI
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
15
Introduction
VOL CH
POWER
1 2 3
4 5 6
7 8
0
9
MENU
MUTE FAV
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
PAGE
PAGE
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
Brief Info.Brief Info.
What is Brief Info?
: Brief Info shows the present screen information.
How to use?
1. Press the INFO button to show the Brief Info on the screen.
2. Press the INFO button or EXIT button to exit.
- The INFO button does not work in Component1,Component2, RGB,
and HDMI/DVI modes.
This function works in the following mode: • Watching
TV/DTV/CATV/CADTV• Watching AV1, AV2
Brief Info Title Test Brief Info Title Test Brief Inf..
SAT, Jan 20, 2005 7:00PM
Multilingual Caption 1080i TV-PG D L S V
6:55AM
DTV 2-1
CC 4:3
Program title
Program start timeBanner information
Program progress bar
Program finish time
Present timeDay of weekMonth, Year
The original aspect ratio of the video is 4:3
The original aspect ratio of the video is 16:9 (wide)
The video resolution is 720x480iThe video resolution is
720x480pThe video resolution is 1280x720pThe video resolution is
1920x1080i
Multilingual: The program contains two or more audioservices.
Press the SAP button to select wanted Audio.
Caption: The program contains one or more caption ser-vices.
Press the CC button to select wanted Closed cap-tion.
V-Chip: The program contains V-Chip information. Referto the
LOCK menu: A (Age), D (Dialogue), L (Language), S(Sex), V
(Violence), FV (Fantasy Violence)
16 : 9
4 : 3
CC
480i480p720p1080i
ABCDEFGHIJ...
10:40AM
Dolby Digital HD
INFO
-
16
Introduction
VOL CH
POWER
1 2 3
4 5 6
7 8
0
9
MENU
MUTE FAV
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
FLASHBK
PAGE
PAGE
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUTEPG (Electronic Program Guide) EPG (Electronic
Program Guide) (In DTV mode)(In DTV mode)
- This system has an Electronic Program Guide (EPG) to helpyour
navigate through all the possible viewing options.
- The EPG supplies information such as program listings,
startand end times for all available services.
- This function can be used only when the EPG information
isbroadcasted by broadcasting companies.
- The EPG displays the program description for next 3 days.-
This function is only supported in DTV mode.
Press the GUIDE button to switch on EPG.
Press the DD / EE / FF / GG button to select desired program,
thenpress the ENTER button to display the selected program.
Press the GUIDE or EXIT button again to switch off EPG andreturn
to TV viewing.
12
3
Remote Control Buttons Function
D / E / F / G Select the desired programChange to the selected
channel
FF / GG Jump PageIFF / GGI Change the dateGUIDE/EXIT Switch off
EPG
GUIDE
Installing Batteries
Open the battery com-partment cover on theback side.
Insert two batteries incorrect polarity (+ with+, - with -).
Don’t mixold or used batterieswith new ones.
Close the cover.* Use a remote control 7 meter distance and
30
degree (left/right) within the receiving unit scope.
* Dispose of used batteries in a recycle bin to
preventenvironmental hazards.
POWER
MENU
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
POWER
MENU
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
1
2
3
32/37/42LC2D** 42/50PC3D**
POWER
MENU
DAY -
GUIDEDAY+
RATIO
VCRTVDVD
ENTER
EXIT TIMER CC INFO
AUDIOCABLE STB
MODE
TV INPUT INPUT
42PC1D**
-
17
Installation
InstallationInstallation
Desktop Pedestal Installation
4 inches 4 inches
4 inches4 inches
4 inches 4 inches
4 inches4 inches
For proper ventilation, allow a clearance of 4" on each side and
from the wall.
GROUNDING
Ensure that you connect the earth ground wire to prevent
pos-sible electric shock. If grounding methods are not
possible,have a qualified electrician install a separate circuit
breaker.Do not try to ground the unit by connecting it to
telephonewires, lightening rods, or gas pipes.
PowerSupply
Short-circuitBreaker
• The TV can be installed in various ways such as on a wall, or
on a desktop etc.• The TV is designed to be mounted
horizontally.
Various Installation
32/37/42LC2D** 42PC1D**, 42PC3D**, 50PC3D**
-
18
Installation
Connect the cables as necessary.After connecting the cables
neat-ly, arrange the cables to theCable Holder.
To connect an additional equip-ment, see the External equip-ment
Connections section.
Reinstall the CABLE MANAGE-MENT as shown.
1
2
Bundle the cables using the sup-plied twister holder.
3
Basic Connection (For 32/37/42LC2D**)Basic Connection (For
32/37/42LC2D**)
InstallationInstallation
32LC2D**
Cable holder
37/42LC2D**
32LC2D** 37/42LC2D**
32LC2D** 37/42LC2D**
Do not hold the CABLE MANAGEMENT when moving the product.- If
the product is dropped, you may be injured or the product may be
broken.
How to remove the CABLE MANAGEMENT
- Hold the CABLE MANAGEMENT with both hands and pull it
upward.
CABLE MANAGEMENT
CABLE MANAGEMENT
-
19
Installation
Place the set with the screen facing down ona cushion or soft
cloth as shown.Before unfolding the stand, please make suretwo
locks (A) on the bottom of the stand pushoutward.
Pull the stand out as shown.After unfolding the stand, please
insert andtighten the screws (provided as parts of theproduct) in
the holes (B) on the bottom of thestand.
1 2
When connecting cables to the set, Do notdisengage the lock
(C).This may cause the set to fall, causing seriousbodily injury
and serious damage to the set.
3
Basic ConnectionBasic Connection
(C)
Hold the CABLE MANAGEMENT with bothhands and push it as
shown.
Connect the cables as necessary.To connect an additional
equipment, see theExternal equipment Connections section.
Reinstall the CABLE MANAGEMENT asshown.
1 2
3
* Image shown here may be slightly different fromyour set.
When closing the stand for storage- First remove the screws in
the holes (B) on the bottom
of the stand. And then pull two Hooks (D) of the standbottom and
fold the stand into the back of the set.
- After folding, push the two Locks (A) of the standbottom
outward.
(A)
(B)
(D)
(A)(B)
How to use stand (For 42PC1D**, 42PC3D**)
How to arrange the cable (For 50PC3D**)
For 42PC1D**, 42PC3D**Arrange the cable as shown.
-
20
Installation
How to join the product assembly to the wall to protect the set
tumbling
- Set it up close to the wall so the product doesn’t fall over
when it is pushed backwards. - The instructions shown below is a
safer way to set up the product, which is to fix it on the wall so
the prod-
uct doesn’t fall over when it is pulled in the forward
direction. It will prevent the product from falling for-ward and
causing injury. It will also prevent the product from damage caused
by fall. Please make surethat children don’t climb on or hang from
the product.
42PC1D**/42PC3D**/50PC3D**
Notes• When moving the product to another place undo the ropes
first.• Use a product holder or a cabinet that is big and strong
enough for the size and weight of the product. • To use the product
safely make sure that the height of the bracket that is mounted on
the wall is same
as that of the product.
2
2
3
1
1
3
Use the eye-bolts or TV brackets/bolts to fix the product to the
wall as shown in the picture. (If your product has the bolts in the
eye-bolts position , loosen the bolts.)* Insert the eye-bolts or TV
brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (not provided as parts
of the product, must purchase separately)on the wall. Match the
height of the bracket that is mounted on the wall.
Use a sturdy rope (not provided as parts of the product, must
purchase separately) to tie the product. It is safer to tie the
rope so it becomes horizontal between the wall and the product.
1
2
3
32/37/42LC2D**
-
21
Installation
Antenna or Cable Connection
Multi-family Dwellings/Apartments(Connect to wall antenna
socket)
Single-family Dwellings /Houses(Connect to wall jack for outdoor
antenna)
Outdoor Antenna
Wall Antenna Socket
VHF Antenna
UHF Antenna
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
AV IN 2
L/MONO
R
AUDIO
S-VIDEO
VIDEO
L/M
ONO
R
AU
DIO
S-VI
DEO
VID
EO
AV IN 2
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
ANTENNAANTENNAININ
CABLEIN
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
Bronze Wire
Be careful not to bend the bronze wire whenconnecting the
antenna.
Analog and Digital TV signals provided on antenna
- Antenna or Cable Service without a Cable Box Connection.- For
optimum picture quality, adjust antenna direction if needed.
Cable TV Wall JackRF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
Analog and Digital TV signals provided on cable
Analog and Digital TV signals provided on cable and antenna
Cable TV Wall Jack
RF Coaxial Wire (75 ohm)
Bronze Wire
Bronze Wire
Turn clockwise to tighten.
Antenna
RF Coaxial Wire (75 ohm)
• In a poor signal area to improve picture quality, purchase and
install a sig-nal amplifier.
• If the antenna needs to be split for two TV’s, install a
“2-Way Signal Splitter”in the connections.
• If the antenna is not installed properly, contact your dealer
for assistance.
AV IN 2
L/MONO
R
AUDIO
S-VIDEO
VIDEO
L/M
ONO
R
AU
DIO
S-VI
DEO
VID
EO
AV IN 2
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
ANTENNAANTENNAININ
CABLEIN
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
External Equipment ConnectionsExternal Equipment Connections
signalamplifier
AV IN 2
L/MONO
R
AUDIO
S-VIDEO
VIDEO
L/M
ONO
R
AU
DIO
S-VI
DEO
VID
EO
AV IN 2
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
ANTENNAIN
CABLECABLEININ
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
AV IN 2
L/MONO
R
AUDIO
S-VIDEO
VIDEO
L/M
ONO
R
AU
DIO
S-VI
DEO
VID
EO
AV IN 2
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
ANTENNAANTENNAININ
CABLECABLEININ
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
NOTE: All cables shown are not included with the TV
-
22
Installation
- To avoid picture noise (interference), leave an adequate
distance between the VCR and TV.
- Typically a frozen still picture from a VCR. If the 4:3
picture format is used; the fixed images on the sidesof the screen
may remain visible on the screen.
VCR Setup
When connecting with an antenna
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
3 4
OUTPUTSWITCH
ANT OUT
ANT IN
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
ANTENNAANTENNAIN
CABLECABLEIN
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
When connecting with a RCA cable
S-VIDEOOUT
IN
(R) AUDIO (L) VIDEO
3 4
OUTPUTSWITCH
ANT OUT
ANT IN
VIDEO AUDIOMONO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1V IN 1
AV OUTV OUT
ANTENNAIN
CABLEIN
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
VCR
1
2
3
Connect the AUDIO/VIDEO jacks between TVand VCR. Match the jack
colors (Video = yellow,Audio Left = white, and Audio Right =
red)
Insert a video tape into the VCR and press PLAYon the VCR.
(Refer to the VCR owner’s manual.)
Select AV1 input source using the INPUT buttonon the remote
control.- If connected to AV IN2, select AV2 input source.
• If you have a mono VCR, connect the audio cable from the VCR
to the AUDIO L/MONO jack of theset.
• This TV finds the connected input sources automatically for
AV1, AV2 and Component 1-2. It is pre-sumed that RGB and HDMI/DVI
sources are connected.
1
1
2
3
4
Connect the RF antenna out socket of the VCR tothe Antenna
socket on the set.
Connect the antenna cable to the RF antenna insocket of the
VCR.
Set VCR output switch to 3 or 4 and then tune TVto the same
channel number.
Insert a video tape into the VCR and press PLAYon the VCR.
(Refer to the VCR owner’s manual.)
VCR
1
2
-
23
Installation
When connecting with an S-Video cable
S-VIDEOOUT
IN
(R) AUDIO (L) VIDEO
3 4
OUTPUTSWITCH
ANT OUT
ANT IN
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
ANTENNAIN
CABLEIN
VIDEO AUDIOMONO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1V IN 1
AV OUTV OUT
VCR
1
12
2
3
4
Connect the S-VIDEO output of the VCR to the S-VIDEO input on
the set. The picture quality isimproved; compared to normal
composite (RCAcable) input.
Connect the audio outputs of the VCR to theAUDIO input jacks on
the set.
Insert a video tape into the VCR and press PLAYon the VCR.
(Refer to the VCR owner’s manual.)
Select AV1 input source with using the INPUTbutton on the remote
control.- If connected to AV IN2, select AV2 input source.
Do not connect to both Video and S-Video at the same time. In
the event that you connectboth Video and the S-Video cables, only
the S-Video will work.
R LAUDIO VIDEO
AV IN 2V IN 2
L/MONOMONO
R
AUDIOAUDIO
S-VIDEOS-VIDEO
VIDEOVIDEO
Camcorder
Video Game Set
1
1
2
3
Connect the AUDIO/VIDEO jacks between TVand external equipment.
Match the jack colors(Video = yellow, Audio Left = white, and
AudioRight = red).
Select AV2 input source with using the INPUTbutton on the remote
control.- If connected to AV IN1 input, select AV1 input
source.
Operate the corresponding external equipment.Refer to external
equipment operating guide.
External AV Source Setup
• This TV finds the connected input sourcesautomatically for
AV1, AV2 and Component 1-2. It is presumed that RGB and
HDMI/DVIsources are connected.
i.e) 32LC2D**
-
24
Installation
DVD Setup
When connecting with a S-Video cable
S-VIDEO(R) AUDIO (L)
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
VIDEOVIDEO AUDIOUDIOMONO( )
VIDEOVIDEO AUDIOUDIO
COMPONENT INCOMPONENT INS-VIDEOS-VIDEO
AV IN 1V IN 1
AV OUTV OUT
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
DVD
1
1
2
2
3
4
5
Connect the S-VIDEO output of the DVD to the S-VIDEO input on
the set.
Connect the audio outputs of the DVD to the AUDIO input jacks on
the set.
Turn on the DVD player, insert a DVD.
Select AV1 input source with using the INPUT button on the
remote control.- If connected to AV IN2, select AV 2 input
source.
Refer to the DVD player's manual for operating instructions.
When connecting with a HDMI cable
1
2
3
Connect the HDMI output of the DVD to theHDMI/DVI IN jack on the
set.
Select HDMI/DVI input source with using theINPUT button on the
remote control.
Refer to the DVD player's manual for operatinginstructions.
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
HDMI-DVD OUTPUT
HDMI/DVI IN DIGITDIGITAL AAL AUDIO UDIO OUTOUT
OPTICAL
RS-232C INRS-232C IN(CONTROLOL & SERVICE)
DVD
1
• TV can receive the video and audio signalsimultaneously by
using a HDMI cable.
• If the DVD supports Auto HDMI function, theDVD output
resolution will be automaticallyset to 1280x720p.
• If the DVD does not support Auto HDMI, youneed to set the
output resolution appropriate-ly. To get the best picture quality,
adjust theoutput resolution of the DVD to 1280x720p.
-
25
Installation
When connecting with a component cable
1
2
3
4
5
Connect the video outputs (Y, PB, PR) of the DVD to the
COMPONENT IN VIDEO jacks on the set.
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO
jacks on the set.
Turn on the DVD player, insert a DVD.
Select Component 1 input source with using the INPUT button on
the remote control.- If connected to COMPONENT 2, select Component
2 input source.
Refer to the DVD player's manual for operating instructions.
• Component Input portsTo get better picture quality, connect a
DVD player to the component input ports as shown below.
Y PB PRComponent ports on the TV
YYYY
PbB-YCbPB
PrR-YCrPR
Video output ports on DVD player
B R (R) AUDIO (L)
VIDEOVIDEO AUDIOUDIOMONO( )
VIDEOVIDEO AUDIOUDIO
COMPONENT INCOMPONENT INS-VIDEOS-VIDEO
AV IN 1V IN 1
AV OUTV OUT
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
DVD
1 2
-
26
Installation
When connecting with a D-sub 15 pin cable
1
2
3
4
Connect the RGB output of the digital set-top boxto the RGB
(PC/DTV) jack on the set.
Connect the audio outputs of the set-top box tothe AUDIO
(RGB/DVI) jack on the set.
Turn on the digital set-top box. (Refer to theowner’s manual for
the digital set-top box.)
Select RGB-DTV input source with using theINPUT button on the
remote control.
- This TV can receive Digital Over-the-air/Cable signals without
an external digital set-top box. However, ifyou do receive Digital
signals from a digital set-top box or other digital external
device, refer to the figureas shown below.
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
(R) AUDIO (L) RGB-DTV OUTPUT
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB INRGB IN
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
REMOTEREMOTECONTROL IN
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
Digital Set-top Box
HDSTB Setup
1
2
When connecting with a HDMI cable
1
2
3
Connect the HDMI output of the digital set-topbox to the
HDMI/DVI IN jack on the set.
Select HDMI/DVI input source with using theINPUT button on the
remote control.
Turn on the digital set-top box. (Refer to theowner’s manual for
the digital set-top box.)
Digital Set-top Box
• TV can receive the video and audio signal simultaneously with
using a HDMI cable.• If the digital set-top box supports Auto HDMI
function, output resolution of the digital set-top box will
be automatically set to 1280x720p.• If the digital set-top box
does not support Auto HDMI, you need to set the output resolution
appro-
priately. To get the best picture quality, adjust the output
resolution of the digital set-top box to1280x720p.
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
HDMI-DTV OUTPUT
HDMI/DVI IN DIGITDIGITAL AAL AUDIO UDIO OUTOUT
OPTICAL
RS-232C INRS-232C IN(CONTR(CONTROLOL & SERVICE)VICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
1
-
27
Installation
When connecting with a Component cable
1
2
3
4
Connect the video outputs (Y, PB, PR) of the digi-tal set-top
box to the COMPONENT IN VIDEOjacks on the set.
Connect the audio output of the digital set-top boxto the
COMPONENT IN AUDIO jacks on the set.
Turn on the digital set-top box. (Refer to theowner’s manual for
the digital set-top box.)
Select Component 1 input source with using theINPUT button on
the remote control.- If connected to COMPONENT 2, select
Component 2 input source.
B R (R) AUDIO (L)
VIDEOVIDEO AUDIOUDIOMONO( )
VIDEOVIDEO AUDIOUDIO
COMPONENT INCOMPONENT INS-VIDEOS-VIDEO
AV IN 1V IN 1
AV OUTV OUT
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
Signal
480i
480p/720p/1080i
Component1/2
Yes
Yes
RGB-DTV, HDMI/DVI
No
Yes
21
Digital Set-top Box
When connecting with a HDMI to DVI cable
1
2
3
4
Connect the DVI output of the digital set-top box to the
HDMI/DVI IN jack on the set.
Connect the audio outputs of the set-top box to the AUDIO
(RGB/DVI) jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual
for the digital set-top box.)
Select HDMI/DVI input source with using the INPUT button on the
remote control.
VIDEO AUDIO( )
VIDEO AUDIO
COMPONENT INS-VIDEO
AV IN 1
AV OUT
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
(R) AUDIO (L)DVI-DTV OUTPUT
HDMI/DVI IN DIGITDIGITAL AAL AUDIO UDIO OUTOUT
OPTICAL
RS-232C INRS-232C IN(CONTR(CONTROL & SERSERVICE)
RGB (PC/DTV)
RGB INRGB IN
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
REMOTEREMOTECONTROL IN
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
Digital Set-top Box
12
• If the digital set-top box has a DVI output and no HDMI
output, a separated audio connection is nec-essary.
• If the digital set-top box supports Auto DVI function, the
output resolution of the digital set-top box willbe automatically
set to 1280x720p.
• If the digital set-top box does not support Auto DVI, you need
to set the output resolution appropri-ately. To get the best
picture quality, adjust the output resolution of the digital
set-top box to1280x720p.
-
28
Installation
Digital Audio Output
1
2
3
Connect one end of an optical cable to the TVDigital Audio
Optical Output port.
Connect the other end of the optical cable to thedigital audio
optical input on the audio equipment.
See the external audio equipment instructionmanual for
operation. When connecting with external audio equip-ments, such as
amplifiers or speakers, pleaseturn the TV speakers off. (Refer to
p.43)
HDMI/DVI IN DIGITDIGITAL AAL AUDIO UDIO OUTOUT
OPTICAL
RS-232C INRS-232C IN(CONTROL & SERVICE)
- Send the TV’s audio to external audio equipment (stereo
system) via the Digital Audio Output Optical port.
CAUTIONDo not look into the optical output port. Looking at the
laser beam may damage your vision.
1/2
Monitor Out Setup
1
2
Connect the second TV or monitor to the TV’s AVOUTPUT jacks.
See the Operating Manual of the second TV ormonitor for further
details regarding that device’sinput settings.
S-VIDEO IN
(R) AUDIO (L) VIDEO
VIDEOVIDEO AUDIOUDIOMONO( )
VIDEOVIDEO AUDIOUDIO
COMPONENT INCOMPONENT INS-VIDEOS-VIDEO
AV IN 1V IN 1
AV OUTV OUT
- The TV has a special signal output capability which allows you
to hook up a second TV or monitor.
1/2
• Component 1-2, RGB-PC/RGB-DTV,HDMI/DVI, DTV input sources
cannot be usedfor Monitor out.
• We recommend to use the video and audiooutput jacks for VCR
recording.
-
29
Installation
- This TV provides Plug and Play capability, meaning that the PC
adjusts automatically to the TV's settings.
PC Setup
When connecting with a D-sub 15 pin cable
1
2
3
4
Connect the RGB output of the PC to the RGB(PC/DTV) jack on the
set.
Connect the PC audio outputs to the AUDIO(RGB/DVI) jack on the
set.
Turn on the PC and the set.
Select RGB-PC input source with using theINPUT button on the
remote control.
(R) AUDIO (L) RGB-PC OUTPUT
RGB (PC/DTV)
RGB INRGB IN
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
REMOTEREMOTECONTROL INCONTROL IN
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
1
2
PC
When connecting with a HDMI to DVI cable
1
2
3
4
Connect the DVI output of the PC to the HDMI/DVI IN jack on the
set.
Connect the audio outputs of the PC to the AUDIO (RGB/DVI) jack
on the set.
Turn on the PC and the set.
Select HDMI/DVI input source with using the INPUT button on the
remote control.
RGB (PC/DTV)
RGB IN
AUDIO (RGB/DVI)
REMOTECONTROL IN
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
(R) AUDIO (L)DVI-PC OUTPUT
HDMI/DHDMI/DVI INVI IN DIGITDIGITAL AAL AUDIO UDIO OUTOUT
OPTICAL
RS-232C INRS-232C IN(CONTR(CONTROLOL & SERSERVICE)VICE)
RGB (PC/DTV)
RGB INRGB IN
AUDIO (RGB/DVI)AUDIO (RGB/DVI)
REMOTEREMOTECONTROL INCONTROL IN
HDMI/DVI IN DIGITAL AUDIO OUT
OPTICAL
RS-232C IN(CONTROL & SERVICE)
REMOTECONTROL
RGB IN(PC/DTV)
AUDIO IN(RGB/DVI)
PC
• If the PC has a DVI output and no HDMI output, a separated
audio connection is necessary.• If the PC does not support Auto
DVI, you need to set the output resolution appropriately. To get
the
best picture quality, adjust the output resolution of PC
graphics card's output resolution to1024x768, 60Hz.
1 2
-
30
Installation
1. To get the best picture quality, adjust the PCgraphics card
to 1024x768, 60Hz.
2. Depending on the graphics card, DOS mode maynot work if a
HDMI to DVI Cable is in use.
3. When Source Devices connected with HDMI/DVIInput, output PC
Resolution (VGA, SVGA, XGA),Position and Size may not fit to
Screen.Press theADJUST button to adjust the screen Position of
TVSET and contact an PC graphics card service cen-ter.
4. When Source Devices connected with HDMI/DVIInput, output TV
SET Resolution (480p, 720p,1080i) and TV SET Display fit
EIA/CEA-861-BSpecification to Screen. If not, refer to the Manualof
HDMI/DVI Source Devices or contact your ser-vice center.
5. In case HDMI/DVI Source Devices is not connect-ed Cable or
poor cable connection, "NO SIGNAL"OSD display in HDMI/DVI Input. In
case that VideoResolution is not supported TV SET output inHDMI/DVI
Source Devices, "INVALID FORMAT"
OSD display. Refer to the Manual of HDMI/DVISource Devices or
contact your service center.
6. Check the image on your TV. There may be noiseassociated with
the resolution, vertical pattern,contrast or brightness in PC,
HDMI/DVI mode. Ifnoise is present, change the PC or HDMI/DVImode to
another resolution, change the refreshrate to another rate or
adjust the brightness andcontrast on the menu until the picture is
clear. If therefresh rate of the PC graphic card can not bechanged,
change the PC graphic card or consultthe manufacturer of the PC
graphic card.
7. Avoid keeping a fixed image on the TV's screen fora long
period of time. The fixed image may becomepermanently imprinted on
the screen.
8. The synchronization input form for Horizontal andVertical
frequencies is separate.
Supported Display Resolution (RGB-PC, HDMI/DVI Mode)
Resolution
* 640x350
* 720x400
640x480
HorizontalFrequency (kHz)
31.468
31.469
31.469
37.861
37.500
70.08
70.08
59.94
72.80
75.00
VerticalFrequency (Hz)
Resolution
* RGB-PC only
800x600
1024x768
HorizontalFrequency (kHz)
35.156
37.879
48.077
46.875
48.363
56.476
60.023
56.25
60.31
72.18
75.00
60.00
70.06
75.02
VerticalFrequency (Hz)
-
31
Installation
* Adjustment for screen Position, Size, and Phase
* Initializing (Reset to original factory values)
- To initialize the adjusted values
Close
POSITION GG
SIZE
PHASE
RESET
Adjust
DD
FF GG
EE
Close
POSITION
SIZE
PHASE
RESET GG
Adjust
Initialize Settings
Position This function is to adjustpicture to left/right
andup/down as you prefer.
Size This function is to mini-mize any vertical bars orstripes
visible on thescreen background. Andthe horizontal screen sizewill
also change.
Phase This function allows you toremove any horizontalnoise and
clear or sharpenthe image of characters.
Mini Glossary
- When RGB is connected to PC input and select the RGB-PC, this
function is used. - When HDMI/DVI is connected to PC input and
select HDMI/DVI input, this function is used. - In RGB-DTV mode,
SIZE and PHASE is not available.- After connecting RGB-PC or
HDMI/DVI to PC input and checking the screen quality.
Press the ADJUST button and then use DD / EE button to
selectPOSITION, SIZE, or PHASE.
Press ENTER button and then use DD / EE / FF / GG buttons tomake
appropriate adjustments.• The PHASE adjustment range is -16 ~
+16.
(In HDMI/DVI-PC mode, PHASE is not available.)• The SIZE
adjustment range is -30 ~ +30.
Press ENTER button.
1
2
3
Press the ADJUST button and then use DD / EE button to selectthe
RESET option.
Press ENTER button and then use FF / GG button to select
Yes.
Press ENTER button.
1
23
Screen Setup for PC mode
4 5 6
7 8
0
9
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
ADJUST
4 5 6
7 8
0
9
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
ADJUST
-
OperationOperationBasic operationBasic operation
1. First, connect power cord correctly. At this moment, the TV
switches to standby mode.
In standby mode to turn TV on, press the , INPUT, CH DD / EE
button on the TV or press the POWER, TVINPUT, INPUT, CH DD / EE,
Number (0 ~ 9) button on the remote control .
2. Select the viewing source by using TV INPUT, INPUT button on
the remote control.This TV is programmed to remember which power
state it was last set to, even if the power cord is out.
3. When finished using the TV, press the POWER button on the
remote control. The TV reverts to standby mode.
1. Press the VOL DD / EE button to adjust the volume.
2. If you want to switch the sound off, press the MUTE
button.
3. You can cancel this function by pressing the MUTE or VOL DD /
EE button.
Press the CH DD / EE or NUMBER buttons to select a channel
number.
- The menus can be shown on thescreen in the selected
language.First select your language.
On Screen Menus Language Selection
Volume Adjustment
Turning on the TV
Channel Selection
Press the MENU button and then use DD / EE button to select
theOPTION menu.
Press the GG button and then use DD / EE button to select
Language.
Press the GG button and then use DD / EE button to select your
desiredlanguage. From this point on, the on-screen menus will be
shown in theselected language.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
23
4
PreviousMENU
Aspect Ratio
Cinema 3:2 Mode
Caption
Caption/Text
Caption Option
Language GISM Method
Low Power
English
Español (Spanish)
Français (French)
Aspect Ratio
Cinema 3:2 Mode
Caption
Caption/Text
Caption Option
Language
ISM Method
Low Power
• If you intend to be away on vacation, disconnect the power
plug from the wall power outlet.
SETUP
VIDEO
AUDIO
TIME
OPTION G
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
32
Operation
-
33
Operation
On Screen Menus Selection and On Screen Menus Selection and
AdjustmentAdjustment
1. Press the MENU button and then DD / EE button to select each
menu.
2. Press the GG button and then use DD / EE / FF / GG button to
display the available menus.
• Your TV's OSD (On Screen Display) may differ slightly from
what is shown in this manual.
How to adjust the OSD screen
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
EZ Picture
Contrast 85
Brightness 50
Color 50
Sharpness 50
Tint 0
Color Temperature
Video Reset
R G
Audio Language
EZ SoundRite
EZ Sound
Balance 0
Treble 50
Bass 50
Front Surround
TV Speaker
BBE
L R
Auto Clock
Manual Clock
Off Timer
On Timer
Sleep Timer
Auto Off
Aspect Ratio
Cinema 3:2 Mode
Caption
Caption/Text
Caption Option
Language
ISM Method
Low Power
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Input Block
SETUP
VIDEO G
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME G
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION G
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK G
* Note: These functions are available in42PC1D**, 42PC3D**,
50PC3D** models only.
-
34
Operation
EZ Scan (Channel Search)
Setup Menu OptionsSetup Menu Options
Press the MENU button and then use DD / EE button to select the
SETUP menu.
Press the GG button and then use DD / EE button to select EZ
Scan.
Press the ENTER button to begin the channel search.Allow EZ Scan
to complete the channel search cycle for ANTENNA, andCABLE.
123
Manual Scan
- A password is required to gainaccess to Manual Scan menu ifthe
Lock System is turned on.
Press the MENU button and then use DD / EE button to select the
SETUP menu.
Press the GG button and then use DD / EE button to select Manual
Scan.
Press the GG button and then use DD / EE button to select TV,
DTV, CATV,and CADTV.
Press the GG button and then use DD / EE button to select
channel num-ber you want to add or delete.
Press the ENTER button to add or delete for the channel
number.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
123
4
56
PreviousMENU
EZ Scan GManual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
Selection ( G or ) leads youto the EZ scan screen.
ANTENNA
CABLE
PreviousMENU
EZ Scan
Manual Scan GChannel Edit
DTV Signal
Input Source
Input Label
Set ID
Select channel type and RF-channel number.
TV 2
Mini Glossary
TV Analog antenna (over-the-air) TV signalDTV Digital antenna
(over-the-air) TV signal
CATV Analog cable TV signalCADTV Digital cable TV signal
- Automatically finds all channelsavailable through antenna
orcable inputs, and stores them inmemory on the channel list.
- Run EZ Scan again after anyAntenna/Cable connection
changes.
- A password is required to gainaccess to EZ Scan menu if
theLock System is turned on.
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
35
Operation
- There are two different ways inorder to add or delete
scannedchannels. One is "Custom List"and the other is "Favorite
List" inthe channel list. Both of them areavailable after EZ Scan
on theSETUP menu.
- A Custom List can be created bytoggling each channel on or
offwith the ENTER button. Thechannels in the Custom List
aredisplayed in black color, and thechannels deleted from theCustom
List are displayed in graycolor. Once a channel is high-lighted you
can add or delete thechannel by referring to the smallwindow at the
top-left corner ofthe screen.You can create yourown Favorite List.
Using the FAVbutton on the remote controlwhen a channel is
highlightedand then you can add or deletethe channel to/from the
FavoriteList.
Channel Edit
Press the MENU button and then use DD / EE button to select the
SETUP menu.
Press the GG button and then use DD / EE button to select
Channel Edit.
Press the GG button. You will now see a screen filled with
channel num-bers and a preview picture.
Use DD / EE / FF / GG button to select a channel and then use
the ENTERbutton to add or delete it. Press FAV button to add the
channel to theFavorite List. The heart-mark will appear in front of
that channel num-ber.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
12
3
4
5
PreviousMENU
EZ Scan
Manual Scan
Channel Edit GDTV Signal
Input Source
Input Label
Set ID
Selection ( G or ) leads you to the channel edit screen.
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
* Custom List
-
36
Operation
DTV Signal Strength
- Shows how strong your DTV sig-nal is and whether you need
toadjust your antenna or digitalcable input. The higher the
signalstrength, the less likely you areto experience picture
degrada-tion.
- DTV Signals: Only when theinput signal is DTV or CADTV,this
function is available.
Press the MENU button and then use DD / EE button to select the
SETUP menu.
Press the GG button and then use DD / EE button to select DTV
Signal.
View the on-screen signal strength monitor to see the quality of
the signalbeing received.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
123
4
PreviousMENU
EZ Scan
Manual Scan
Channel Edit
DTV Signal GInput Source
Input Label
Set ID
Bad Normal Good
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
- Changes the picture source soyou can watch your TV, cable
TV,VCR, DVD, or any other devicesthat are connected to your TV.
Input Source
Press the MENU button and then use DD / EE button to select the
SETUP menu.
Press the GG button and then use DD / EE button to select Input
Source.
Press the GG button and then use DD / EE button to select the
source:Antenna, Cable, AV1, AV2, Component1, Component2, RGB-DTV
(orRGB-PC), or HDMI/DVI.• To toggle RGB-DTV and RGB-PC, select
RGB-DTV(or RGB-PC) and
press GG button.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
123
4
PreviousMENU
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source GInput Label
Set ID
Antenna
Cable
AV1
AV2
Component1
Component2
RGB-PC
HDMI/DVI
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
Setup Menu Options continuedSetup Menu Options continued
-
37
Operation
- Sets a label to each input sourceor lets you skip the input
sourcewhich is not in use when youpress INPUT button.
Input Label
Press the MENU button and then use DD / EE button to select the
SETUP menu.
Press the GG button and then use DD / EE button to select Input
Label.
Press the GG button and then use DD / EE button to select the
source: AV1-2, Component1-2, RGB or HDMI/DVI.
Press the FF / GG button to select the label.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
123
4
5
PreviousMENU
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label GSet ID
AV1 Cable Box
AV2 VCR
Component1 DVD
Component2 Set Top Box
RGB PC
HDMI/DVI Game
SETUP G
VIDEO
AUDIO
TIME
OPTION
LOCK
EZ Scan
Manual Scan
Channel Edit
DTV Signal
Input Source
Input Label
Set ID
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
38
Operation
APM (Adaptive Picture Mode)
- It allows a viewer to select theirpreferred mode after
comparingpicture (Daylight, Normal, NightTime and Custom)
settings.
- Note: While operating the 4-split,any button except APM,
ENTER,EXIT, DD / EE / FF / GG, VOLUME DD /EE , MUTE button on the
remotecontrol are not available.
VVideo Menu Optionsideo Menu Options
EZ Picture
- EZ Picture adjusts the TV for the bestpicture appearance.
Select the presetvalue in the EZ Picture menu based onthe program
category.
- When adjusting Video menu options (con-trast, brightness,
color, sharpness, tint,and color temperature) manually, EZPicture
automatically changes to Custom.
- Daylight, Normal, Night Time,Movie, Video Game, and Sports
set-tings are preset for optimum picture qual-ity at the factory
and are not adjustable.
Press the EZ PIC button repeatedly to select the picture
appear-ance setup option as shown below: Custom (your own
settings),Daylight, Normal, Night Time, Movie, Video Game,
andSports.• You can also adjust EZ Picture in the VIDEO menu.
Press the EXIT button to save and return to TV viewing.
1
2
Press the APM button. The screen is divided to 4-split.
Press the DD / EE / FF / GG button to navigate 4 EZ Pictures. By
pressingthe ENTER button, you can select the desired mode.
Press the EXIT button to save and return to TV viewing.
12
Night Time
Navigate Select Exit
Custom
Daylight Normal
FF GG
GGFF
EXIT
1 2 3
4 5 6
7 8
0
9
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
EZ PIC
4 5 6
7 8
0
9
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
APM
-
39
Operation
Color Temperature Control
PreviousMENU
EZ Picture
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature GVideo Reset
Cool
Medium
Warm
PreviousMENU
EZ Picture
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Video Reset G Selection ( G or ) resets tothe factory settings
(default).
EZ Picture
Contrast 85
Brightness 50
Color 50
Sharpness 50
Tint 0
Color Temperature
Video Reset
R G
- Choose one of three automaticcolor adjustments. Set to warmto
enhance hotter colors such asred, or set to cool to see lessintense
colors with more blue.
- Use to quickly reset all the Videomenu options to their
original fac-tory preset values.
Press the MENU button and then use DD / EE button to select the
VIDEO menu.
Press the GG button and then use DD / EE button to select Video
Reset.
Press the GG button to reset the Video menu options to original
values.
123
Press the MENU button and then use DD / EE button to select the
VIDEO menu.
Press the GG button and then use DD / EE button to select the
desired pic-ture option (Contrast, Brightness, Color, Sharpness, or
Tint).Press theGG button and then use FF / GGbutton to make
appropriate adjustments.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1234
Manual Picture Control (EZ Picture-Custom option)
- Adjust the picture appearance tosuit your preference and
viewingsituations.
PreviousMENU
EZ Picture
Contrast 85 GBrightness 50
Color 50
Sharpness 50
Tint 0
Color Temperature
Video Reset
R G
Contrast 90 FF G
EE
Video Reset
Press the MENU button and then use DD / EE button to select the
VIDEO menu.
Press the GG button and then use DD / EEbutton to select Color
Temperature.
Press the GG button and then use DD / EE button to select either
Cool,Medium, or Warm.Press EXIT button to return to TV viewing or
press MENU button toreturn to the previous menu.
123
4
SETUP
VIDEO G
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO G
AUDIO
TIME
OPTION
LOCK
EZ Picture
Contrast 85
Brightness 50
Color 50
Sharpness 50
Tint 0
Color Temperature
Video Reset
R G
SETUP
VIDEO G
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
40
Operation
Audio Menu OptionsAudio Menu Options
- Other languages may be availableif a digital signal is
provided by thebroadcasting station.
- Scans for changes in sound levelduring commercials, then
adjuststhe sound to match the specifiedaudio level. EZ
SoundRitemakes sure that the volume levelremains consistent whether
youare watching a commercial or aregular TV program.
Audio Language
EZ SoundRite
PreviousMENU
Audio Language GEZ SoundRite
EZ Sound
Balance
Treble
Bass
Front Surround
TV Speaker
BBE
English
Spanish
French
PreviousMENU
Audio Language
EZ SoundRite GEZ Sound
Balance
Treble
Bass
Front Surround
TV Speaker
BBE
Off
On
Press the MENU button and then use DD / EE button to select
theAUDIO menu.
Press theGG button and then use DD / EE button to select Audio
Language.
Press the GG button and then use DD / EE button to select:
English,Spanish, or French.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
2
3
4
Press the MENU button and then use DD / EE button to select
theAUDIO menu.
Press the GG button and then use DD / EE button to select EZ
SoundRite.
Press the GG button and then use DD / EE button to select Off or
On.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
2
3
4
Audio Language
EZ SoundRite
EZ Sound
Balance 0
Treble 50
Bass 50
Front Surround
TV Speaker
BBE
L R
Audio Language
EZ SoundRite
EZ Sound
Balance 0
Treble 50
Bass 50
Front Surround
TV Speaker
BBE
L R
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
41
Operation
EZ Sound
Manual Sound Control (EZ Sound-Custom option)
- EZ Sound lets you enjoy the bestsound without any special
adjust-ment because the TV sets theappropriate sound options
basedon the program content.
- When adjusting sound options(treble, bass, and front
surround)manually, EZ Sound automatical-ly switches Custom.
- Normal, Stadium, News, Music,and Theater are preset for
goodsound quality at the factory andare not adjustable.
- Adjust the sound in your prefer-ence and surrounded
environ-ment.
Press the EZ SOUND button repeatedly to select the appropriate
soundsetup as shown below: Custom (your own settings),
Normal,Stadium, News, Music, and Theater.
• You can also adjust EZ Sound in the AUDIO menu.
Press EXIT button to save and return to TV viewing.
1
2
Press the MENU button and then use DD / EE button to select
theAUDIO menu.
Press the GG button and then use DD / EE button to select the
desiredsound option (Balance, Treble, or Bass).
Press the GG button and then use FF / GG button to make
appropriateadjustments.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
2
3
4
PreviousMENU
Audio Language
EZ SoundRite
EZ Sound
Balance 0 GTreble 80
Bass 80
Front Surround
TV Speaker
BBE
L R
EE
Balance 0 FF GL R
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
1 2 3
4 5 6
7 8
0
9
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
EZ SOUND
-
42
Operation
Audio Menu Options continuedAudio Menu Options continued
- is a trademark of SRSLabs, Inc.
- TruSurround XT technology isincorporated under license fromSRS
Labs, Inc.
- Manufactured under license fromDolby Laboratories. “Dolby”
andthe double-D symbol are trade-marks of Dolby Laboratories.
Stereo/SAP Broadcasts Setup
Front Surround
Press the MENU button and then use DD / EE button to select
theAUDIO menu.
Press the GG button and then use DD / EE button to select
FrontSurround.
Press the GG button and then use DD / EE button to select Off,
3DEchoSound System or SRS (Sound Retrieval System) TruSurround
XT.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
2
3
4
PreviousMENU
Audio Language
EZ SoundRite
EZ Sound
Balance
Treble
Bass
Front Surround GTV Speaker
BBE
Off
3D EchoSound System
SRS TruSurround XT
Audio Language
EZ SoundRite
EZ Sound
Balance 0
Treble 50
Bass 50
Front Surround
TV Speaker
BBE
L R
Use the SAP button to select your desired MTS mode in analog
signal.Each time you press the SAP button, Mono, Stereo, or SAP
appear inturn. • If other languages available on the digital
signal, select them with the
SAP button.
Press EXIT button to save and return to TV viewing.
1
2
Mini Glossary
SRS TruSurround XTTakes advantage of any multi-channel format
without needing to add extra speakers or equipment. Dialog clarity,
bass enrichment,and the addition of stereo audio enhancement that
produces an immersive sound experience from standard stereo
material.
3D EchoSound SystemCreates a stunning simulated stereo effects
from any mono sound and a realistic three-dimensional sound with a
very wide anddeep sound stage from stereo sound.
- This TV can receive MTS stereo pro-grams and any SAP
(Secondary AudioProgram) that accompanies the stereoprogram; if the
station transmits anadditional sound signal as well as theoriginal
one.
- When having selected Stereo or SAPbutton on the remote
control, this TVcan only receive the signal when thatthe TV station
transmits the proper sig-nals.
- Mono sound is automatically receivedif the broadcast is only
in Mono; eventhough Stereo or SAP has been select-ed.
- Select Mono if you want to listen to themono sound in remote
fringe areasduring stereo/SAP broadcasting.
- Stereo or SAP can be received inAnalog channel.
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
1 2 3
4 5 6
7 8
0
9
APMADJUST
SAPEZ SOUNDEZ PIC FREEZE
FLASHBK
SAP
-
43
Operation
- BBE High Definition Soundrestores clarity and presence
forbetter speech intelligibility andmusic realism.
TV Speakers On/Off Setup
- Turn TV speakers off if usingexternal audio equipment.Feature
turns the TV Speakersoption On or Off.
BBE
Press the MENU button and then use DD / EE button to select
theAUDIO menu.
Press the GG button and then use DD / EE button to select
BBE.
Press the GG button and then use DD / EE button to select Off or
On.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
2
34
PreviousMENU
Audio Language
EZ SoundRite
EZ Sound
Balance
Treble
Bass
Front Surround
TV Speaker GBBE
Off
On
Press the MENU button and then use DD / EE button to select
theAUDIO menu.
Press the GG button and then use DD / EE button to select TV
Speaker.
Press the GG button and then use DD / EE button to select Off or
On.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1
2
3
4
PreviousMENU
Audio Language
EZ SoundRite
EZ Sound
Balance
Treble
Bass
Front Surround
TV Speaker
BBE G
Off
On
Audio Language
EZ SoundRite
EZ Sound
Balance 0
Treble 50
Bass 50
Front Surround
TV Speaker
BBE
L R
Audio Language
EZ SoundRite
EZ Sound
Balance 0
Treble 50
Bass 50
Front Surround
TV Speaker
BBE
L R
• Manufactured under license from BBE Sound, Inc.
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO G
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
44
Operation
TTime Menu Optionsime Menu Options
- If current time setting is wrong,reset the clock manually.
Auto Clock Setup
Manual Clock Setup
Press the MENU button and then use DD / EE button to select the
TIME menu.
Press the GG button and then use DD / EE button to select Auto
Clock.
Press the GG button and then use DD / EE button to select
On.
Press the GG button and then use DD / EE button to select your
viewingarea time zone.• U.S.A: Eastern, Central, Mountain, Pacific,
Alaska, or Hawaii.• Canada: Eastern, Central, Mountain, Pacific,
Nfld, or Atlantic.
Press the GG button and then use DD / EE button to select Auto,
Off, On,depending on whether or not your viewing area observes
DaylightSaving time.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
12
3
4
5
6
Press the MENU button and then use DD / EE button to select the
TIME menu.
Press the GG button and then use DD / EE button to select
ManualClock.
Press the GG button and then use FF / GG button to select either
the year,date, or time option. Once selected, use the DD / EE
button to set the year,date, and time options.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
12
3
4
PreviousMENU
Auto Clock GManual Clock
Off Timer
On Timer
Sleep Timer
Auto Off
Off
On
Time Zone Eastern
AutoDaylightSaving
Auto Clock
Manual Clock
Off Timer
On Timer
Sleep Timer
Auto Off
PreviousMENU
Auto Clock
Manual Clock GOff Timer
On Timer
Sleep Timer
Auto Off
Year - - - -
Date - - / - -
Time - - : - - - -
Auto Clock
Manual Clock
Off Timer
On Timer
Sleep Timer
Auto Off
- The time is set automaticallyfrom a digital channel
signal.
- The current time will be set auto-matically from a digital
channelsignal provided by the broadcast-ing station.
- Set the clock manually, if the cur-rent time is set
incorrectly by theauto clock function.
SETUP
VIDEO
AUDIO
TIME G
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME G
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
45
Operation
On/Off Timer Setup
Sleep Timer
- Timer function operates only ifcurrent time has been set.
- Off-Timer function overrides On-Timer function if they are set
bothset to the same time.
- The TV must be in standby modefor the On-Timer to work.
- If you do not press any buttonwithin 2 hours after the TV
turnson with the On Timer function,the TV will automatically revert
tostandby mode.
- The Sleep Timer turns the TV offat the preset time. Note that
thissetting is cleared when the TV isturned off.
- You can also set up the SleepTimer in the TIME menu.
Press the MENU button and then use DD / EE button to select the
TIME menu.
Press the GG button and then use DD / EE button to select Off
Timer orOn Timer.
Press the GG button and then use DD / EE button to select On.•
To cancel On/Off Timer function, select Off.
Press the GG button and then use DD / EE button to set the
hour.
Press the GG button and then use DD / EE button to set the
minutes.
For only On Timer functionPress the GG button and then use DD /
EE button to select the channel atturn-on.
Press the GG button and then use DD / EE button to set the sound
level atturn-on.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
12
3
4
56
7
PreviousMENU
Auto Clock
Manual Clock
Off Timer
On Timer GSleep Timer
Auto Off
Off
On
Time 6 : 30 AM
Ch. TV 2-0
Vol 17
Press the TIMER button repeatedly to select the number of
minutes.First the Off option appears on the screen, followed by the
followingsleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240
minutes.
When the number of minutes you want is displayed on the
screen,press the TIMER button. The timer begins to count down from
the num-ber of minutes selected.
To check the remaining minutes before the TV turns off, press
theTIMER button once.
To cancel the Sleep Timer, press the TIMER button repeatedly to
select Off.
1
2
3
4
Auto Clock
Manual Clock
Off Timer
On Timer
Sleep Timer
Auto Off
SETUP
VIDEO
AUDIO
TIME G
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
MENU
DAY -
GUIDEDAY+
RATIO
ENTER
PAGE
EXIT TIMER CC INFOTIMER
-
46
Operation
TTime Menu Options continuedime Menu Options continued
Auto Off
- If the TV is on and there is noinput signal, the TV turns
offautomatically after 10 minutes.
Press the MENU button and then use DD / EE button to select the
TIME menu.
Press the GG button and then use DD / EE button to select Auto
Off.
Press the GG button and then use DD / EE button to select Off or
On.
Press EXIT button to return to TV viewing or press MENU button
toreturn to the previous menu.
1234
PreviousMENU
Auto Clock
Manual Clock
Off Timer
On Timer
Sleep Timer
Auto Off G Off
On
If set to On and there is no
input signal, the TV turns off
automatically after 10
minutes.
Auto Clock
Manual Clock
Off Timer
On Timer
Sleep Timer
Auto Off
SETUP
VIDEO
AUDIO
TIME G
OPTION
LOCK
SETUP
VIDEO
AUDIO
TIME
OPTION
LOCK
-
47
Operation
Aspect Ratio Control
Option Menu FeaturesOption Menu Features
- Lets you choose the way an ana-log picture with a 4:3 aspect
ratiois displayed on your TV with a16:9 ratio picture format.
Whenyou receive an analog picturewith a 4:3 aspect ratio on
your16:9 TV, you need to specify howthe picture is to be
displayed.
- If you are viewing a picture with a16:9 aspect ratio, you
can’t usethe Horizon aspect ratio option.
- Horizon aspect ratio is not avail-able for Component 1-2
(720p/1080i)/ RGB-DTV (720p/1080i)/HDMI/DVI-DTV (720p/1080i)
/DTV(720p/1080i)input source.
- In RGB-PC/DVI-PC input source,only either 4:3 or 16:9
aspectratio is available.
- If a fixed image is displayed onthe screen for a long time,
theimage may become imprintedon the screen and remain visi-ble.
Press the RATIO button repeatedly to select the desired picture
format. • You can also adjust Aspect Ratio in the OPTION menu.
• Set By ProgramSelects the proper picture proportion to match
the source’s image.(4:3 →→ 4:3, 16:9 →→ 16:9)
• 4:3Choose 4:3 when you want to view a picture with an original
4:3aspect ratio, with gray bars appearing at both the left and
right sides.
• 16:9Choose 16:9 when you want to adjust the picture
horizontally, in a lin-ear proportion to fill the entire
screen.
• HorizonChoose Horizon when you want to adjust the picture in a
non-linearproportion, that is, more enlarged at both sides, to
create a panoramaview.
• Zoom 1Choose Zoom 1 when you want to view the picture without
any alter-ation. However, the top and bottom portions of the
picture will becropped.
• Zoom 2Choose Zoom 2 when you want the picture to be altered,
both hori-zontally extended and vertically c