Please read this manual carefully and completely before oper- ating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. LCD TV PLASMA TV OWNER’S MANUAL LCD TV MODELS 26LC2R 32LC2R 32LC3R PLASMA TV MODELS 42PC1R 42PC1RV 42PC1RVH 42PC7R 42PC7RH
LCD TV MODELS 26LC2R 32LC2R 32LC3R PLASMA TV MODELS 42PC1R 42PC1RV 42PC1RV H 42PC7R 42PC7RH
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Please read this manual carefully and completely before oper-ating your set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
LCD TV PLASMA TVOWNER’S MANUALLCD TV MODELS
2 6 L C 2 R3 2 L C 2 R3 2 L C 3 R
PLASMA TV MODELS
4 2 P C 1 R4 2 P C 1 RV4 2 P C 1 RV H4 2 P C 7 R4 2 P C 7 R H
WA
RN
ING
1
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WWARNING
Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.
Do not place the product in direct sunlight ornear heat sources such as heat registers,stove and so on.
This may cause a fire.
Do not use the product in damp place suchas a bathroom or any place where it is likelyto get wet.
This may cause a fire or could give an electric shock.
Bend antenna cable between inside and out-side building to prevent rain from flowing in.
This may cause water damaged inside the product and could
give an electric shock.
Earth wire should be connected.
If the earth wire is not connected, there is possible a danger
of electric shock caused by the current leakage.
If grounding methods are not possible, a separate circuit
breaker should be employed and installed by a qualified
electrician.
Do not connect ground to telephone wires, lightning rods
or gas pipe.
Do not placing anything containing liquid ontop of the product.
This may cause a fire or could give an electric shock.
Wet Location Marking :
Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed
on the apparatus.
Do not insert any object into the exhaust vent.
This may cause a fire or could give an electric shock.
Do not place heavy objects on the product.
This may cause serious injury to a child or adult.
Important safety instructions shall be provided with each apparatus. This information shall be given in a se-parate booklet or sheet, or be located before any operating instructions in an instruction for installation foruse and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended tobe used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safetyinstructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safe-ty information may be included by adding statements after the end of the following safety instruction list. Atthe manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction maybe placed immediately adjacent to that safety instruction :
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Owner Manual
Powersupplier
Short-circuitbreaker
WA
RN
ING
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Owner Manual
Do not use water the product while cleaning.
This may cause damaged the product or could give an elec-
tric shock.
In case of smoke or strange smell from theproduct, switch it off, unplug it from the walloutlet and contact your dealer or servicecenter.
This may cause a fire or could give an electric shock.
Do not attempt to service the product your-self. Contact your dealer or service center.
This may cause damaged the product or could give an electric
shock.
During a lightning thunder, unplug the productfrom the wall outlet and don’t touch anantenna cable.
This may cause damaged the product or could give an elec-
tric shock.
Never touch the power plug with a wet hand.
This may cause an electric shock.
Disconnect from the mains and remove allconnections before moving.
Do not place the product in a built-in
installation such as a bookcase or rack.
Ventilation required.
When installing the product on a table, becareful not to place the edge of its stand.
This may cause the product to fall, causing serious injury to
a child or adult, and serious damage to the product.
Do not place an outside antenna in the vicinityof overhead power lines or other electric lightor power circuits.
This may cause an electric shock.
There should be enough distance between anoutside antenna and power lines to keep theformer from touching the latter even whenthe antenna falls.
This may cause an electric shock.
Do not pull the cord but the plug whenunplugging.
This may cause a fire.
Owner Manual
WWARNING WNOTE
Owner Manual
WA
RN
ING
3
WARNING
Ensure the power cord doesn’t trail acrossany hot objects like a heater.
This may cause a fire or an electric shock.
Do not plug when the power cord or the plugis damaged or the connecting part of thepower outlet is loose.
This may cause a fire or an electric shock.
Dispose of used batteries carefully to protecta child from eating them.
In case that it eats them, take it to see a doctor immediately.
When moving the product assembled withspeakers do not carry holding the speakers.
This may cause the product to fall, causing serious injury to
a child or adult, and serious damage to the product.
Unplug this product from the wall outletbefore cleaning. Do not use liquid cleaners oraerosol cleaners.
This may cause damaged the product or could give an electric
shock.
Contact the service center once a year toclean the internal part of the product.
Accumulated dust can cause mechanical failure.
The distance between eyes and the screenshould be about 5 - 7 times as long as diag-onal length of the screen.
If not, eyes will strain.
Unplug the product from the wall outlet whenit is left unattended and unused for long periodsof time.
Accumulated dust may cause a fire or an electric shock from
deterioration or electric leakage.
Only use the specified batteries.
This make cause damaged the product or could give an
What is a Plasma TV ?Using plasma is the best way to achieve flat paneldisplays with excellent image quality and largescreen sizes that are easily viewable. The Plasma TVcan be thought of as a descendant of the neonlamp and or a series of fluorescent lamps.
How does it work?Plasma TV is an array of cells, known as pixels, whichare comprised of three sub-pixels, corresponding tothe colors red, green, and blue. Gas in a plasmastate is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue).These phosphors are the same types used inCathode Ray Tube (CRT) devices such as televisionsand common computer monitors.
Plasma TV offers a rich, dynamic display becauseeach sub-pixel is individually controlled by advancedelectronics to produce over 16 million different col-ors. This means that you get perfect images that areeasily viewable in a display that is fewer than fiveinches thick.
160° - Wide angle range of visionYour flat panel plasma screen offers an exceptionallybroad viewing angle of over 160 degrees. Thismeans that the display is clear and visible to viewersanywhere in the room.
Wide ScreenThe wide screen offers a theater-like experience inyour own home.
Multimedia Connect your plasma display to a PC and use it forconferencing, games, and Internet browsing. ThePicture-in-Picture feature allows you to view your PCand video images simultaneously.
VersatileThe light weight and thin size makes it easy toinstall your plasma display in a variety of locationswhere conventional TVs do not fit.
The Plasma TV Manufacturing Process: a fewminute colored dots may be present on thePlasma TV screen
The Plasma TV is composed of 0.9 to 2.2 millioncells. A few cell defects will normally occur in thePlasma TV manufacturing process. Several tiny,minute colored dots visible on the screen should beacceptable. This also occurs in other Plasma TVmanufacturers' products. The tiny dots appearingdoes not mean that this Plasma TV is defective.Thus a few cell defects are not sufficient cause forthe Plasma TV to be exchanged or returned. Ourproduction technology minimizes these cell defectsduring the manufacture and operation of this product.
FOR LCD TVIf the TV feels cold to the touch, there may be asmall “flicker” when it is turned on. This is normal,there is nothing wrong with TV.
Some minute dot defects may be visible on thescreen, appearing as tiny red, green, or blue spots.However, they have no adverse effect on the moni-tor's performance.
Avoid touching the LCD screen or holding your finger(s)against it for long periods of time. Doing so may pro-duce some temporary distortion effects on the screen.
OOnn DDiissppoossaall
a. The fluorescent lamp used in this product con-tains a small amount of mercury.
b. Do not dispose of this product with generalhousehold waste.
c. Disposal of this product must be carried out inaccordance to the regulations of your localauthority.
7
ACCESSORIES
INT
ROD
UC
TIO
N
Ensure that the following accessories are included with your product. If an accessory is missing, please con-tact the dealer where you purchased the product.
Owner's Manual
1.5V 1.5V
Owner’s Manual Batteries(some models)
ENTER
INPUT
TV
TV
INPUT
PIP CH-PIP CH+
PIP INPUT
DVD
ARC
EXIT
VOLREVIEW
MUTE CH
SLEEP
MEMORY/ERASEMENU
CAPTIONPIP
SIZEPOSTION
VCR
POWER
1
2
3
4
5
6
7
8
9
*0
FCR
MTS
ENTER
INPUT
TV
TV
INPUT
PIP CH-PIP CH+
PIP INPUT
DVD
ARC
EXIT
VOLREVIEW
MUTE CH
SLEEP
MEMORY/ERASEMENU
CAPTIONPIP
SIZEPOSTION
VCR
POWER
1
2
3
4
5
6
7
8
9
*0
MTS
FCR
Remote Control Power Cord
2-TV brackets2-Wall brackets
2-TV bracket bolts
FFoorr 2266LLCC22RR//3322LLCC22RR//3322LLCC33RR
4-bolts for stand assembly(Refer to p.15)
3322LLCC22RR oonnllyy
Cable Management(Refer to p.19)
Twister HolderArrange the wires
with the twister holder.
RF AdapterYou must connect it to the antennawire after fixing in Antenna Input.This adapter is only supplied in
Argentina.
2-Wall brackets
or
2-eye-bolts
FFoorr 4422PPCC11RR**//4422PPCC77RR**
Polishing clothPolish the screen with the cloth.
4422PPCC11RR** oonnllyy
2-bolts for stand assembly(Refer to p.14.)
* Slightly wipe stained spot on the exterior only with the cleansing cloths forthe product exterior if there is stain or fingerprint on surface of the exterior.
* Do not wipe roughly when removing stain. Please be cautious of that exces-sive power may cause scratch or discoloration.
8
INT
ROD
UC
TIO
N
CONTROLS
INTRODUCTION
This is the front panel of models 42PC1R* TVs.■ This is a simplified representation of the front panel. Here shown may be somewhat different from your TV.
PRVOLOKMENUINPUT
Front Panel Controls
PRVOLOKMENUINPUT
CHVOLENTERMENUINPUT
Power/Standby Indicator• illuminates red in standby mode.• illuminates green when the set is switched on.
42PC7R*
42PC1R*
Power/Standby Indicator• illuminates red in standby mode.• illuminates white when the set is
switched on.
CHANNEL Buttons
VOLUME ButtonsMENU Button
ENTER Button
INPUT Button
POWER Button
CHVOLENTERMENUINPUT
CHANNEL Buttons
VOLUME ButtonsMENU Button
ENTER Button
INPUT Button
POWER Button
CHVOLENTERMENUINPUT
CHVOLENTERMENUINPUT
Remote Control Sensor
9
INT
ROD
UC
TIO
N
CONNECTION OPTION
This is the back panel of model 42PC1R*.
VID
EO
AU
DIO
RL/
MO
NO
AV IN 2
REMOTECONTROL IN
AUDIO IN(RGB)
AC IN
MONO( )AUDIO
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
HDMI IN
ANTENNAIN
VIDEOS-VIDEO
AUDIO OUTVARIABLE
VIDEO AUDIO
COMPONENT IN
AV IN 2
L/MONO
R
AUDIOAUDIO
VIDEOVIDEO
1
2
AV IN
1
AV OUT
Component Input 1/2Connect a component video/audio device tothese jacks.
Remote Control PortConnect your wired remote control here.
RGB/Audio InputConnect the monitor output from a PC to theappropriate input port.
HDMIConnect a HDMI signal to HDMI port with HDMIcable.
Power Cord SocketThis TV operates on an AC power. The voltage isindicated on the product Specifications page.Never attempt to operate the TV on DC power.
AV OUT Connect a second TV or Monitor.
S-Video InputConnect S-Video out from an S-VIDEO device.
Audio/Video InputConnect audio/video output from an externaldevice to these jacks.
RS-232C INPUT(CONTROL/SERVICE)PORTConnect the serial port of the control devices tothe RS-232C jack.
Variable Audio OutputConnect an external amplifier or add a subwooferto your surround sound system.
Antenna InputConnect over-the-air signals to this jack.
AUDIO InputConnections are available for listening stereo soundfrom an external device.
VIDEO InputConnects the video signal from a video device.
1
2
3
4
7
5
6
8
9
10
11
6
7 8
1
32
9
4
10 11
5
42PC1R*
5
42PC7R*
12 12
12
10
INT
ROD
UC
TIO
N
INTRODUCTION
This is the front panel of models 26/32LC2R/32LC3R TVs.■ This is a simplified representation of the front panel. Here shown may be somewhat different from your TV.
CONTROLS
R
CH
VOL
ENTER
MENU
INPUT
Remote Control Sensor
Power/Standby Indicator• illuminates red in standby mode.
• illuminates white when the set is switched on.
R
Remote Control Sensor
Power/Standby Indicator• illuminates red in standby mode.
• illuminates white when the set is switched on.
32LC3R
CHCH
VOLVOL
ENTERENTER
MENUMENU
INPUTINPUT
CHANNEL Buttons
VOLUME Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
26/32LC2R
Front Panel Controls
11
CONNECTION OPTIONS
INT
ROD
UC
TIO
N
This is a back panel of 26LC2R/32LC2R/32LC3R.
( )AUDIO
RGB IN(PC/DTV) HDM IN
ANTENNAIN
VIDEOS-VIDEO
AV IN
1
AUDIO OUTVARIABLE
VIDEO AUDIO
COMPONENT IN
AV OUT
AV IN 2
L/MONO
R
AUDIOAUDIO
VIDEOVIDEO
VIDE
O
AV IN 2
L/M
ONO
R
AUDI
O
RS-232C IN(CONTROL & SERVICE)
VIDE
O
AV IN 2
L/MON
OR
AUDI
O
REMOTE�CONTROL IN
AUDIO IN�(RGB)
MONO( )AUDIO
RGB IN(PC/DTV) HDM IN
ANTENNAIN
VIDEOS-VIDEO
AV IN
1
AUDIO OUTVARIABLE
VIDEO AUDIO
COMPONENT IN
AV OUT
AV IN 2
L/MONO
R
AUDIO
VIDEO
RS-232C IN(CONTROL & SERVICE)
Back Connection Panel
AUDIO InputConnections are available forlistening stereo sound froman external device.
VIDEO InputConnects the video signalfrom a video device.
COMPONENT INConnect a component video/audio device tothese jacks.
AV OUTConnect a second TV or monitor.
AV (Audio/Video) IN 1 Connect audio/video output from an externadevice to these jacks.S-VIDEO Connect S-Video out from an S-VIDEO device.
Remote Control PortConnect your wired remote control.
RGB/AUDIO INConnect the monitor output from a PC to theappropriate input port.
HDMI INConnect a HDMI signal.Or DVI(VIDEO)signal to the this port with a DVIto HDMI cable.
VARIABLE AUDIO OUTConnect an external amplifier or add a subwooferto your surround sound system.
RS-232C IN (CONTROL &SERVICE) PORTConnect to the RS-232C port on a PC.
ANTENNA INConnect over-the-air signals to this jack.
Power Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DC
power.
1
2
3
1
7
6
8
9
10
2
3
4
5
5
9
4
6
7
8
10
32LC2R 32LC3R26LC2R
INT
ROD
UC
TIO
N
12
REMOTE CONTROL KEY FUNCTIONSWhen using the remote control, aim it at the remote control sensor on the TV.
INTRODUCTION
ENTER
INPUTTVTV
INPUT
PIP CH- PIP CH+ PIP INPUT
DVD
ARC
EXIT
VOLREVIEW
MUTE
CH
SLEEP
MEMORY/ERASE MENU
CAPTION PIP SIZE POSTION
VCR
POWER
1 2 3
4 5 6
7 8 9
* 0 FCR
MTS
POWER
TV INPUT
INPUT
ARC
Brightnessadjustment
PIP
SIZE
POSITION
PIP CH - /+
*
PIP INPUT
VCR/DVD control buttons
EXIT
MEMORY/ERASE
MENU
MTS
SLEEP
Turns your TV or any other programed equipment
on or off, depending on mode.
Returns to the TV mode.
If you press the button once, the input source OSDwill appear on screen as shown. Press the DD / EE buttonand then ENTER button to select the desired input source(TV, AV1, AV2, Component 1, Component 2, RGB, orHDMI).
Selects your desired picture format.
GG RReeffeerr ttoo pp..6600
Adjusts screen brightness.It returns to the default settings brightness by changingmode source.
Switches the sub picture PIP, DW mode.
Adjusts the sub picture size.
Moves the sub picture.
Selects a channel for the sub picture.
Not funtional
Selects the input source for the sub picture in PIP/Twinpicture mode.
Controls some video cassette recorders or DVD playerswhen you have already selected DVD or VCR mode button.
Clears all on-screen displays and returns to TV viewingfrom any menu.
Memorizes or erases selected channel.
Selects a menu.
Selects the MTS sound: Mono, Stereo, or SAP.
Sets the sleep timer.
13
INT
ROD
UC
TIO
N
ENTER
INPUTTVTV
INPUT
PIP CH- PIP CH+ PIP INPUT
DVD
ARC
EXIT
VOLREVIEW
MUTE
CH
SLEEP
MEMORY/ERASE MENU
CAPTION PIP SIZE POSTION
VCR
POWER
1 2 3
4 5 6
7 8 9
* 0
MTS
FCR
CAPTION
THUMBSTICK(Up/Down/Left
Right)
ENTER
MODE
VOLUME UP/DOWN
REVIEW
MUTE
CHANNELUP/DOWN
0~9 numberbutton
FCR
Selects CAPTION mode.
Allows you to navigate the on-screen menus andadjust the system settings to your preference.
Accepts your selection or displays the current mode.
Selects the remote operating modes.
Increases/decreases the sound level.
Returns to the previously viewed channel.
Switches the sound on or off.
Selects available channels found during Manual scan.
Selects a channel.Selects numbered items in a menu.
Selects a favorite channel.
Installing Batteries■ Open the battery compartment cover on the
back side and install the batteries matchingcorrect polarity (+ with +, - with -).
■ Install two 1.5V AA batteries. Don’t mix old orused batteries with new ones.
■ Close cover.
■ Use a remote control up to 7meters distance and 30degree (left/right) within thereceiving unit scope.
■ Dispose of used batteries ina recycle bin to preserveenvironment.
TVD/A
INPUT DVD
ARC
LIST I/IIMENU
TEXT PIP GUIDE INFO
VCR
POWER
R
TVD/A
INPUT DVD
ARC
TEXT PIP GUIDE INFO
VCR
POWER
Remote control effective range
INT
ROD
UC
TIO
N
14
STAND INSTALLATION
INSTALLATION
Installation InstructionUnfolding the stand base
Figures shown here may be slightly different from your set.
First remove the screws in the holes (B)on the bottom of thestand. And then pull two Hooks (D)of the stand bottom andfold the stand into the back of the set.
After folding, push two Locks (A)of the stand bottom outward.
NOTE!
■ Place the set with the screen facing down on a cushion or soft cloth as shown in Figures 1.Before unfolding the stand, please make sure two locks (A)on the bottom of the stand push outward.
■ Pull the stand out as shown above in Figures 2 ~ 3. After unfolding the stand, please insert and tighten the screws in the holes (B)on the bottom of the stand.
■ When connecting cables to the set,Do not disengage the lock (C).This may cause the set to fall, causing serious bodily injury and serious damage to the set.
A
CB
1 2
3 4
■ This feature is not available for all models.
ADB
INT
ROD
UC
TIO
N
15
STAND INSTALLATION
INSTALLATION
Carefully place the product screenside down on a cushioned surface thatwill protect product and screen fromdamage.
Place the product stand on the productas shown.
Stand Installation for 32LC2R
Install the 4 bolts securely, in the backof the product in the holes provided.
DESKTOP PEDESTAL INSTALLATIONFor proper ventilation, allow a clearance of 4incheson each side from the wall.
R
4 inches
4 inches
26/32LC2R/32LC3R
GG Ensure adequate ventilation by following the clearance recommendations.
CAUTION
4 inches4 inches
16
INT
ROD
UC
TIO
N
INSTALLATION
Desktop Pedestal Installation
4 inches
4 inches4 inches
4 inches
PRVOLOKMENUINPUT
For proper ventilation, allow a clearance of 4" on each side and from the wall.
Wall Mount: Horizontal installation
4 inches
4 inches
4 inches
4 inches
4 inches
For proper ventilation, allow a clearance of 4" on each side and from the wall. Detailed installation instruc-tions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
GROUNDING
Ensure that you connect the earth ground wire to preventpossible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connectingit to telephone wires, lightening rods, or gas pipes.
PowerSupply
Short-circuitBreaker
■ The TV can be installed in various ways such as on a wall, or on a desktop etc.■ The TV is designed to be mounted horizontally.
<<OOnnllyy 4422PPCC11RR**>>Remove two screws of the backside of the set beforeinstalling the wall mounting bracket.
17
INT
ROD
UC
TIO
N
HOW TO JOIN THE PRODUCT ASSEMBLY TO THE WALL TOPROTECT THE SET TUMBLING
42PC1R*/42PC7R*
26/32LC2R/32LC3R
2
1
3
■ Set it up close to the wall so the product doesn’t fall over when it is pushed backwards.■ The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the
product doesn’t fall over when it is pulled in the forward direction. It will prevent the product fromfalling for-ward and hurting people. It will also prevent the product from damage caused by fall. Pleasemake sure that children don’t climb on or hang from the product.
1
2
3
Use the bracket and the bolt to fix the product to the wall as shown in the picture.
Secure the bracket with the bolt (not provided as parts of the product, must purchase separately) on the wall.
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product.It is safer to tie the rope so it becomes horizontal between the wall and the product.
NOTE!GG When moving the product to another place undo the ropes first.GG Use a product holder or a cabinet that is big and strong enough for the size and weight of the product.GG To use the product safely make sure that the height of the bracket that is mounted on the wall is same
as that of the product.
2
3
1
INT
ROD
UC
TIO
N
BASIC CONNECTION
18
INSTALLATION
Arrange the cables as shown picture.
Connect the cables as necessary.After connecting the cables neatly,arrange the cables to the Cable Holder.
To connect an additional equipment, seethe CCoonnnneeccttiioonn && SSeettuupp section.
1
BASIC CONNECTION (Only 26LC2R/32LC2R/32LC3R)
4422PPCC11RR**
4422PPCC77RR**
19
INT
ROD
UC
TIO
N
Install the CCAABBLLEE MMAANNAAGGEEMMEENNTTas shown.
2
Bundle the cables using the suppliedtwister holder.
3
GG FFoorr 2266//3322LLCC22RR
Hold the CCAABBLLEE MMAANNAAGGEEMMEENNTT with bothhands and pull it upward.
NOTE!
GG Do not hold the CABLE MANAGEMENT when moving the product.If the product is dropped, you may be injured or the product may be broken.
HOW TO REMOVE THE CABLE MANAGEMENT
GG FFoorr 3322LLCC33RR
Hold the CCAABBLLEE MMAANNAAGGEEMMEENNTT with bothhands and pull it downward.
20
ANTENNA CONNECTION
CONNECTIONS & SETUP
CO
NN
ECT
ION
S & SET
UP
■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■ In poor signal areas, to get better picture quality,install a signal amplifier to the antenna asshown to the right.
■ If signal needs to be split for two TVs, use anantenna signal splitter for connection.
SSiiggnnaall AAmmpplliiffiieerr
UHFVHF
Multi-family Dwellings/Apartments(Connect to wall antenna socket)
Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)
Outdoor Antenna
Wall Antenna Socket
VHF Antenna
UHF Antenna
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
ANTENNAIN
ANTENNAIN
CO
NN
ECT
ION
S & SET
UP
21
■ To avoid picture noise (interference), leave an adequate distance between the VCR and TV.■ Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides
of the screen may remain visible on the screen.
AV 1 AV 2
VIDEO AUDIO
COMPONENT IN
AV IN 3
VIDEOS-VIDEO( )AUDIO
ANTENNAIN
AV 1 AV 2
VIDEO AUDIO
COMPONENT IN
AV IN 3
VIDEOS-VIDEO( )AUDIO
VIDEOS-VIDEO( )AUDIO
AV IN 3
VIDEOS-VIDEO( )AUDIO
AV IN 3
HDMI IN
AUDIO OUTVARIABLE
S-VIDEOOUT
IN
(R) AUDIO (L) VIDEO3 4
OUTPUTSWITCH
ANT OUT
ANT IN
ANTENNAIN
VVCCRR
1
2
VCR SETUP
When connecting with an antenna
Connect the AANNTT OOUUTT socket of the VCR to theAANNTTEENNNNAA IINN socket on the set.
Connect the antenna cable to the RF antennasocket of the VCR.
Press the PPLLAAYY button on the VCR and match theappropriate channel between the TV and VCR forviewing.
S-VIDEO
OUT
IN
(R) AUDIO (L) VIDEO3 4
OUTPUTSWITCH
ANT OUT
ANT IN
( )AUDIOVIDEOS-VIDEO
AV IN
1
HDMI/DVI IN
UPGRADE(MODULE)
AUDIO OUTVARIABLE
ANTENNAIN
MONO( )AUDIOVIDEOS-VIDEO
AV IN
1
VIDEO AUDIO
COMPONENT IN
1
2
AV OUT
VVCCRR
1
1
2
3
When connecting with a RCA cable
Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV and VCR.Match the jack colors (Video = yellow, Audio Left = white,and Audio Right = red).
Insert a video tape into the VCR and press PLAY on theVCR. (Refer to the VCR owner’s manual.)
Select AAVV11 input source using the IINNPPUUTT button on theremote control.- If connected to AAVV IINN 22, select AAVV22 input source.
1
2
3
NOTE!GG If you have a mono VCR, connect the audio cable from the VCR to the AAUUDDIIOO LL//MMOONNOO jack of the set.
CO
NN
ECT
ION
S & SET
UP
22
VCR SETUP
S-VIDEO
OUT
IN
(R) AUDIO (L) VIDEO3 4
OUTPUTSWITCH
ANT OUT
ANT IN
MONO( )AUDIOVIDEOS-VIDEO
AV IN
1
VIDEO AUDIO
COMPONENT IN
1
2
AV OUT
HDMI/DVI IN
UPGRADE(MODULE)
AUDIO OUTVARIABLE
ANTENNAIN
( )AUDIOVIDEOS-VIDEO
AV IN
1
VVCCRR
12
When connecting with an S-Video cable
Connect the S-VIDEO output of the VCR to the SS--VVIIDDEEOOinput on the set. The picture quality is improved; com-pared to normal composite (RCA cable) input.
Connect the audio outputs of the VCR to the AAUUDDIIOOinput jacks on the set.
Insert a video tape into the VCR and press PLAY on theVCR. (Refer to the VCR owner’s manual.)
1
2
3
Select AAVV11 input source with using the IINNPPUUTT button onthe remote control.4
NOTE!GG If both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-
VIDEO can be received.
AV IN 2
L/MONOMONO
R
AUDIOAUDIO
VIDEOVIDEO
R LAUDIO VIDEO
Camcorder
Video Game Set
1
EXTERNAL EQUIPMENT CONNECTIONS
Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TVand external equipment. Match the jack colors(Video = yellow, Audio Left = white, and Audio Right= red).
Select AAVV22 input source with using the IINNPPUUTTbutton on the remote control.- If connected to AAVV IINN11 input, select AAVV11 input
source.
Operate the corresponding external equipment.Refer to external equipment operating guide.
1
2
3
CO
NN
ECT
ION
S & SET
UP
23
DVD SETUP
( )AUDIOVIDEOS-VIDEO
AV IN
1
VIDEO AUDIO
COMPONENT IN
1
2
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
B R (R) AUDIO (L)
MONO( )AUDIOVIDEOS-VIDEO
AV IN
1
AV OUT
DDVVDD
1 2
When connecting with a component cable
Connect the video outputs (Y, PB, PR) of the DVD to theCCOOMMPPOONNEENNTT IINN VVIIDDEEOO jacks on the set.
Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO jacks on the set.
Turn on the DVD player, insert a DVD.
1
2
3Select CCoommppoonneenntt22 input source using the IINNPPUUTT buttonon the remote control.- If connected to CCoommppoonneenntt 11, select CCoommppoonneenntt11
input source.
4
Refer to the DVD player's manual for operating instructions.
5
NOTE!GG CCoommppoonneenntt IInnppuutt ppoorrttss
To get better picture quality, connect a DVD player to thecomponent input ports as shown below.
Y PB PRComponent ports on the TV
YYYY
PbB-YCbPB
PrR-YCrPR
Video output ports on DVD player
MONO( )AUDIOVIDEOS-VIDEO
AV IN
1
VIDEO AUDIO
COMPONENT IN
1
2
AV OUT
VIDEO AUDIO
COMPONENT IN
1
2
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
S-VIDEO(R) AUDIO (L)DDVVDD
12
When connecting with a S-Video cable
Connect the S-VIDEO output of the DVD to the SS--VVIIDDEEOOinput on the set.
Connect the audio outputs of the DVD to the AAUUDDIIOOinput jacks on the set.
Turn on the DVD player, insert a DVD.
1
2
3
Select AAVV11 input source with using the IINNPPUUTT button onthe remote control.
4
Refer to the DVD player's manual for operating instructions.
5
24
CO
NN
ECT
ION
S & SET
UP
CONNECTIONS & SETUP
( )AUDIOVIDEOS-VIDEO
AV IN
1
VIDEO AUDIO
COMPONENT IN
1
2
REMOTECONTROL IN
AUDIO IN(RGB)
RGB IN(PC/DTV)
RS-232C IN(CONTROL(CONTROL & SERSERVICE)
AUDIO OUTVARIABLE
HDMI IN
HDMI-DVD OUTPUT
DDVVDD
11
When connecting with a HDMI cable
Connect the HDMI output of the DVD to the HHDDMMII IINNjack on the set.
Select HHDDMMII input source with using the IINNPPUUTT buttonon the remote control.
Refer to the DVD player's manual for operating instructions.
1
2
3
NOTE!GG TV can receive the video and audio signal simultaneously with using a HDMI cable.
GG If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to1280x720p.
GG If the DVD does not support Auto HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the DVD to 1280x720p.
CO
NN
ECT
ION
S & SET
UP
25
STB (SET-TOP BOX) SETUP
( )AUDIOVIDEOS-VIDEO
AV IN
1
VIDEO AUDIO
COMPONENT IN
1
2
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
B R (R) AUDIO (L)
MONO( )AUDIOVIDEOS-VIDEO
AV IN
1
AV OUT
DDiiggiittaall SSeett--ttoopp BBooxx
1 2
When connecting with a component cable
Connect the video outputs (Y, PB, PR) of the digital set-top boxto the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO jacks on the set.
Connect the audio output of the digital set-top box to theCCOOMMPPOONNEENNTT IINN AAUUDDIIOO jacks on the set.
Turn on the digital set-top box. (Refer to the owner’s manual forthe digital set-top box.)
1
2
3
Select CCoommppoonneenntt22 input source using the IINNPPUUTT button onthe remote control.- If connected to CCoommppoonneenntt 11, select CCoommppoonneenntt11 input
source.
4
NOTE! Signal
480i
480p/720p/1080i
Component
Yes
Yes
RGB-DTV
No
Yes
HDMI
No
Yes
RS-232C IN(CONTROL & SERVICE)
HDMI IN
AUDIO OUTVARIABLE
RGB IN(PC/DTV)
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
REMOTECONTROL IN
AUDIO IN(RGB)
(R) AUDIO (L)DVI-DTV OUTPUT
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
DDiiggiittaall SSeett--ttooppBBooxx
1
2
When connecting with a HDMI to DVI cable
Connect the DVI output of the digital set-top box to the HHDDMMIIIINN jack on the set.
Connect the audio outputs of the set-top box to the AAUUDDIIOOIINN ((RRGGBB//DDVVII)) jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual forthe digital set-top box.)
1
2
3Select HHDDMMII input source with using the IINNPPUUTT button on theremote control.4
GG If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is
necessary.
GG If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box willbe automatically set to 1280x720p.
GG If the digital set-top box does not support Auto DVI, you need to set the output resolution appropriately.To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p.
NOTE!
CO
NN
ECT
ION
S & SET
UP
26
CONNECTIONS & SETUP
REMOTECONTROL IN
RS-232C IN(CONTROL & SERVICE)
HDMI IN
AUDIO OUTVARIABLE
RGB INRGB IN(PC/DTV)
AUDIO IN(RGB)
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
(R) AUDIO (L) RGB-DTV OUTPUT
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
DDiiggiittaall SSeett--ttoopp BBooxx
12
When connecting with a D-sub 15 pin cable
Connect the RGB output of the digital set-top box to theRRGGBB IINN ((PPCC//DDTTVV)) jack on the set.
Connect the audio outputs of the set-top box to theAAUUDDIIOO IINN ((RRGGBB//DDVVII)) jack on the set.
Turn on the digital set-top box. (Refer to the owner’smanual for the digital set-top box.)
1
2
3
Select RRGGBB--DDTTVV input source with using the IINNPPUUTTbutton on the remote control.
4
RS-232C IN(CONTROL & SERVICE)
HDMI IN
AUDIO OUTVARIABLE
RGB IN(PC/DTV)
RGB IN(PC/DTV)
RS-232C IN(CONTROL & SERVICE)
AUDIO OUTVARIABLE
HDMI IN
REMOTECONTROL IN
AUDIO IN(RGB)
RGB IN(PC/DTV)(PC/DTV)
RS-232C IN(CONTROL & SERSERVICE)
AUDIO OUTVARIABLE
HDMI IN
HDMI OUTPUT
11
When connecting with a HDMI cable
Connect the HDMI output of the digital set-top box to theHHDDMMII IINN jack on the set.
Select HHDDMMII input source with using the IINNPPUUTT buttonon the remote control.
Turn on the digital set-top box. (Refer to the owner’s man-ual for the digital set-top box.)
1
2
3
NOTE!GG TV can receive the video and audio signal simultaneously with using a HDMI cable.
GG If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will beautomatically set to 1280x720p.
GG If the digital set-top box does not support Auto HDMI, you need to set the output resolution
appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to1280x720p.
DDiiggiittaall SSeett--ttoopp BBooxx
CO
NN
ECT
ION
S & SET
UP
27
NOTE!
To enjoy vivid picture and sound, connect a PC tothe set.
Avoid keeping a fixed image on the set’s screenfor a long period of time. The fixed image maybecome permanently imprinted on the screen;use a screen saver when possible.
Connect PC to the RGB INPUT(PC INPUT) portof the set; change the resolution output of PCaccordingly.
There might be a noise according to some reso-lution, vertical pattern, contrast or brightness inPC mode. Then change the PC mode into otherresolution or change the refresh rate into otherrate or adjust the brightness and contrast on themenu until the picture is clean. If the refresh rateof the PC graphic card can not be changed,change the PC graphic card or consult it to themanufacturer of the PC graphic card.
The synchronization input form for Horizontaland Vertical frequencies is separate.
We recommend using 640x480, 60Hz(42PC1RV/42PC1RVH)/1360x768, 60Hz(26/32LC2R/32LC3R/42PC1R/42PC7R/42PC7RH)for the PC mode, they provide the best picturequality.
If the resolution of PC is over UXGA, there will beno picture on the set.
Connect the audio cable from the PC to theAudio input on the set. (Audio cables are notincluded with the set).
When you use too long RGB-PC cable, theremight be a noise on the screen. We recommendusing under 5m of the cable. It provides the bestpicture quality.
This set does not support HDMI-PC.
RGB-PC 640*350 mode is only for DOS, it ispossible that dose not full the whole screen.
44
55
1
2
3
6
7
8
9
PC SETUP
REMOTECONTROL IN
RS-232C IN(CONTROL & SERVICE)
HDMI IN
AUDIO OUTVARIABLE
RGB INRGB IN(PC/DTV)
AUDIO IN(RGB)
AUDIO RGB-PC OUTPUT PC
12
■ This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
When connecting with a D-sub 15 pin cable
Connect the RGB output of the PC to the RRGGBB IINN((PPCC//DDTTVV)) jack on the set.
Connect the audio outputs of the PC to the AAUUDDIIOO IINN((RRGGBB//DDVVII)) jack on the set.
Turn on the PC and the set.
1
2
3
Select RRGGBB--PPCC input source with using the IINNPPUUTT buttonon the remote control.
If your TV will be turned on, you will be able to use its features.
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
■ In standby mode to turn TV on, press the , IINNPPUUTT,CCHH DD / EE button on the TV or press the PPOOWWEERR, TTVV,IINNPPUUTT, CCHH ++//--, NNuummbbeerr((00~99)) button on the remotecontrol and then the TV will switch on.
VOL CH
CAPTION
ENTER
INPUTTVTV
INPUT
PIP CH- PIP CH+ PIP INPUT
DVD
ARC
EXIT
REVIEW
MUTE
SLEEP
MEMORY/ERASE MENU
PIP SIZE POSTION
VCR
POWER
1 2 3
4 5 6
7 8 9
* 0
MTS
FCR
CAPTION
VOL CH
Turning on the TV
Press the VVOOLL ++//-- button to adjust the volume.
If you want to switch the sound off, press the MMUUTTEE button.
You can cancel this function by pressing the MMUUTTEE,
VVOOLL ++//-- or MMTTSS button.
Volume Adjustment
Press the CCHH ++//-- or NUMBER button to select a channelnumber.
Channel Adjustment
NOTE!GG If you intend to be away on vacation, disconnect the power plug from wall power outlet.
30
TV M
ENU
TV MENU
PIP (PICTURE-IN-PICTURE)
ENTER
INPUTTVTV
INPUT
PIP CH- PIP CH+ PIP INPUT
DVD
ARC
EXIT SLEEP
MEMORY/ERASE MENU
CAPTION PIP SIZE POSTION
VCR
POWER
MTS
Watching PIP
Press the PP IIPP button to access the sub picture. Each press of PIP changes the PIPoptions as shown below.
PIP lets you view 2 different inputs (sources) on your TV screen atthe same time. One source will be large, and the other source willshow a smaller inset image.
PIP function is available in the Component, RGB, HDMI mode. (But,it can’t adjust 480i resolution of Component/HDMI mode.) for themain picture.
PIP Mode DW2 Mode
PIP Off
Channel Selection for Sub Picture
Press the PPIIPP CCHH ++//-- button to select a channel for the sub picture.
The selected channel number is displayed just below the channel number of main picture.
Input Source Selection for Sub PicturePress the PPIIPP IINNPPUUTT button to select the input source for the sub picture. Each press of PPIIPP IINNPPUUTT button is pressed, each input source for the sub picture is displayed.Sub picture can be selected only TV, AV1, AV2 modes.
Sub Picture Size Adjustment (PIP mode only)Press the SSIIZZEE button to adjust the sub picture size.
With SSIIZZEE button in PIP mode, sub picture is adjusted.
Moving the Sub Picture (PIP mode only)
Press the PPOOSSIITTIIOONN button. Repeatedly press the PPOOSSIITTIIOONN button then sub picture moves up/down/left/right.
TV M
ENU
31
Press the MMEENNUU button and then DD / EE button to display each menu.
Press the GG button and then DD / EE button to select a menu item.
Change the setting of an item in the sub or pull-down menu with F / G button.You can move to the higher level menu by pressing the EENNTTEERR or MMEENNUU button.
ON SCREEN MENUS SELECTION AND ADJUSTMENTYour TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.The OSD mainly use pictures for the 42PC1RV.
Auto Program should be used to memorize all the active channels inyour area before you are able to use the TV.There are two ways of storing channels in the TV's memory. You canuse either.One is called AUTO PROGRAM and the other is called MANUALPROGRAM.In AUTO PROGRAM mode, the TV will memorize the channels inascending numerical order. If there are additional channels you wantto add or delete, you can manually add or delete those channels withManual Program.
Channel
DE F G MENU
Auto program
Manual program
Favorite channel
Channel
DE F G MENU
Auto program G
Manual program
Favorite channel
To start
- Redo Auto Program if the TV is ever moved to another location.- Auto Program will search for channels only through the Antenna
jack.- If channels numbers for broadcast over-the air TV and cable TV are
duplicated where different channels have the same number, pressthe same number buttons again to toggle between:
(For example, press 17 to go to the channel, press 17 again to go tothe duplicated channel.)
Broadcast TV Channels Cable TV Channels
Press the MMEENNUU button and then DD // EE button to selectthe Channel menu.
Press the GG button and then DD // EE button to select Auto program.
Press the GG button. AUTO PROGRAM starts the channelsearch.
If you want to stop auto programming, press the MMEENNUUbutton.Only the channels found up to at that time are memorized.
1
2
3
4
1
2 3
TV M
ENU
33
TV MENU Channel Menu Options
MANUAL PROGRAM: ADDING/DELETING CHANNELS
You can add or delete channels from the channel scan manually. EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
* 0 FCR
ENTER
REVIEW
MEMORY/ERASE MTS
Use the CH-/+ or NUMBER buttons to select the channel number you want to add or delete.
Press the MMEEMMOORRYY//EERRAASSEE button.
• You can also do Manual program with the Channel menu.
1
2
34
TV MENU Channel Menu Options
TV M
ENU
FINE TUNING
Press the MMEENNUU button and then DD // EE button to select the
Channel menu.
Press the GG button and then DD // EE button to select Manual
program.
Press the GG button and then DD // EE button to select Fine.
Press the FF // GG button to to fine tune for the best pictureand sound.
Press the EENNTTEERR button to store it.
Press the EEXXIITT button to return to normal TV viewing.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
1
2
3
4
5
6
3 4
Normally fine tuning is only necessary if reception is poor.
1
Auto program
Manual program
Favorite channel
Channel
DE F G MENU
Channel
DE F G MENU
Auto program
Manual program G
Favorite channelTV 7
Memory on
Fine 0
2
Channel
F G DE MENU
Auto program
Manual program
Favorite channelTV 7
Memory on
Fine -2
TV M
ENU
35
Press the MMEENNUU button and then DD // EE button to selectthe Channel menu.
Press the GG button and then DD // EE button to select Favorite Channel.
Press the GG button.
Press the DD // EE button to select - - - - - - -.
Select a desired program with the FF // GG button.
To store another program, repeat steps 4 to 5.
You can store up to 8 programs.
Press the EEXXIITT button to return to normal TV viewing.
This function lets you select your favorite Channels directly.
Repeatedly press the FCR button to select stored favoriteChannels.
CClleeaarr Select this option to display with a sharp image.OOppttiimmuumm The most general and natural screen display status.SSoofftt Select this option to display with a mild image.
UUsseerr 11//22 Select this option to use the user-defined setting.
Press the MMEENNUU button and then DD // EE button to select the Picture menu.
Press the GG button and then DD // EE button to select APC.
Press the GG button and then DD // EE button to select Clear, Optimum, Soft, User 1, or User 2.
Press the EEXXIITT button to return to TV viewing or press theMMEENNUU button to return to the previous menu.
AA APC adjusts the TV for the best picture appearance.
Select the preset value in the APC menu based on theprogram category.
AA CClleeaarr, OOppttiimmuumm and SSoofftt, are programmed for optimumpicture reproduction at the factory and cannot bechanged.
1
2
3
41
2 3
APC
ACC
Advanced
Reset
Picture
DE F G MENU
Picture
DE F G MENU
APC G
ACC
Advanced
Reset
ClearOptimumSoftUser 1User 2
TV M
ENU
37
Press the MMEENNUU button and then DD // EE button to select the Picture menu.
Press the GG button and then DD // EE button to select APC.
Press the GG button and then DD // EE button to select User 1,or User 2.
Press the GG button and then DD // EE button to select the
Press the GG button and then press the FF // GG button tomake appropriate adjustments.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
PICTURE ADJUSTMENT (APC-USER OPTION)
CCoonnttrraasstt Adjusts the difference between the light and dark levels inthe picture.
BBrriigghhttnneessss Increases or decreases amount of white in the your picture.CCoolloorr Adjusts intensity of all colors. SShhaarrppnneessss Adjusts the level of crispness in the edges between the light
and dark areas of the picture. The lower the level, the softerthe image.
TTiinntt Adjusts the balance between red and green levels.
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
NOTE!
- You can’t adjust color, sharpness and tint in the RGB-PCmode to the levels you prefer.
To initialize values (reset to default settings), select the Cooloption.
Choose one of three automatic color adjustments. Set to warm toenhance hotter colors such as red, or set to cool to see less intensecolors with more blue.
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
Press the MMEENNUU button and then DD // EE button to select
the Picture menu.
Press the GG button and then DD // EE button to select ACC.
Press the GG button and then DD // EE button to select
either Cool, Normal, Warm, or User.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
1
2
3
41
2 3
Picture
DE F G MENU
APC
ACC G
Advanced
Reset
CoolNormalWarmUser
APC
ACC
Advanced
Reset
Picture
DE F G MENU
TV M
ENU
39
You can adjust red, green, blue to any color temperature you prefer.
MANUAL COLOR TEMPERATURE CONTROL (ACC - USER OPTION)
Press the MMEENNUU button and then DD // EE button to select
the Picture menu.
Press the GG button and then DD // EE button to select ACC.
Press the GG button and then DD // EE button to select User.
Press the GG button and then DD // EE button to select
Red, Green, or Blue.
Press the GG button and then press the FF // GG button to
make appropriate adjustments.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
User
DE F G MENU
Red +30 GGreen 0Blue 0
Red +25 F G
E
4 5
1
2
3
4
5
6
1
2 3
Picture
DE F G MENU
APC
ACC G
Advanced
Reset
CoolNormalWarmUser
APC
ACC
Advanced
Reset
Picture
DE F G MENU
40
TV MENU Picture Menu Options
TV M
ENU
Press the MMEENNUU button and then DD // EE button to select
the Picture menu.
Press the GG button and then DD // EE button to select XD.
Press the GG button and then DD // EE button to select
Auto or Manual.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
** SSeelleeccttiinngg tthhee MMaannuuaall
- This menu is activated after selecting the User1 or User2 of AAPPCC.
Press the GG button and then DD // EE button to select XDContrast, XD Color or XD NR.
Press the GG button and then DD // EE button to select On or Off.
Press the EEXXIITT button to return to TV viewing or press theMMEENNUU button to return to the previous menu.
XD is LG electronic's unique picture improving technology to display areal HD source through an advanced digital signal processing algo-rithm.It’s not available to use this function in RGB-PC mode.
FUNCTION
Manual
DE F G MENU
OnOff
XD Contrast G
XD Color
XD NRAA XXDD CCoonnttrraasstt :: Optimizing the contrast automatically
according to the brightness of the reflection.
AA XXDD CCoolloorr :: Adjusting the colors of the reflection auto-matically to reproduce as closely as possible to the nat-ural colors.
AA XXDD NNRR :: Removing the noise up to the point where itdoes not damage the original picture.
1
2
3
4
1
2
3
1 2
1
2 3
Picture
DE F G MENU
APC
ACC
Advanced
Reset
AutoManual
G
APC
ACC
Advanced
Reset
Picture
DE F G MENU
TV M
ENU
41
ADVANCED-CINEMA
Set up the TV for the best picture appearance for viewingmovies.
This feature operates only in Analog TV, Video andComponent 480i mode.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
ENTER
REVIEW
MEMORY/ERASE MTS
Press the MMEENNUU button and then DD // EE button to select the Picture menu.
Press the GG button and then DD // EE button to selectAdvanced.
Press the GG button and then DD // EE button to selectCinema.
Press the GG button and then DD // EE button to select
On or Off.
Press the EEXXIITT button to return to TV viewing or press theMMEENNUU button to return to the previous menu.
1
2
3
4
5
4
1
2 3
Picture
DE F G MENU
To set
APC
ACC
Advanced G
Reset
Advanced
DE F G MENU
OnOff
Cinema G
Black Level
APC
ACC
Advanced
Reset
Picture
DE F G MENU
42
TV MENU Picture Menu Options
TV M
ENU
ADVANCED-BLACK LEVEL
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
ENTER
REVIEW
MEMORY/ERASE MTS
When you watch the movie, this function adjusts the set to thebest picture appearance. Adjusting the contrast and the bright-ness of the screen using the black level of the screen.This function works in the following mode: Video (NTSC-M), S-Video or HDMI.
Press the MMEENNUU button and then DD // EE button to select the Picture menu.
Press the GG button and then DD // EE button to selectAdvanced.
Press the GG button and then DD // EE button to selectBlack Level.
Press the GG button and then DD // EE button to select Lowor High.
AA LLooww :: The reflection of the screen gets darker.
AA HHiigghh :: The reflection of the screen gets brighter.
Press the EEXXIITT button to return to TV viewing or press theMMEENNUU button to return to the previous menu.
1
2
3
4
5
3 4
1
2
Picture
DE F G MENU
To set
APC
ACC
Advanced G
Reset
Advanced
DE F G MENU
LowHigh
Cinema
Black Level G
APC
ACC
Advanced
Reset
Picture
DE F G MENU
TV M
ENU
43
RESET
1
2 3
Picture
DE F G MENU
APC
ACC
Advanced
Reset G
Press the MMEENNUU button and then DD // EE button to select
the Picture menu.
Press the GG button and then DD // EE button to select Reset.
Press the GG button to initialize the adjusted value.
• Returns to the default settings APC, ACC, XD, Advanced
at the factory.
To set
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
1
2
3
APC
ACC
Advanced
Reset
Picture
DE F G MENU
44
TV M
ENU
TV MENU Sound Menu Options
DIGITAL AUTO SOUND PROCESSING (DASP)
You can select your preferred sound setting; Surround MAX, Flat,Music, Movie or Sports and you can also adjust the sound fre-quency of the equalizer.DASP lets you enjoy the best sound without any special adjustmentbecause the TV sets the appropriate sound options based on theprogram content.Surround MAX, Flat, Music, Movie, and Sports are preset forgood sound quality at the factory and are not adjustable.
SSuurrrroouunndd MMAAXX Select this option to sound realistic.FF llaatt The most commanding and natural audio.MMuussiicc Select this option to enjoy the original sound when lis
tening to the music.MMoovviiee Select this option to enjoy sublime sound.SSppoorrttss Select this option to watch sports broadcasting.UUsseerr Select this option to use the user-defined audio
settings.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
ENTER
REVIEW
MEMORY/ERASE MTS
Press the MMEENNUU button and then DD // EE button to select the Sound menu.
Press the GG button and then DD // EE button to select DASP.
Press the GG button and then DD // EE button to selectSurround MAX, Flat, Music, Movie, Sports or User.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
1
2
3
4
1
2 3
DASP
AVL
Balance 0
Speaker
Sound
DE F G MENU
Surround MAXFlatMusicMovieSportsUser
Sound
DE F G MENU
DASP G
AVL
Balance 0
Speaker
TV M
ENU
45
SOUND FREQUENCY ADJUSTMENT (DASP - USER OPTION)
Press the MMEENNUU button and then DD // EE button to select
the Sound menu.
Press the GG button and then DD // EE button to select DASP.
Press the GG button and then DD // EE button to select User.
Press the GG button.
Select a sound band by pressing the FF // GG button.
Make appropriate sound level with the DD // EE button.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
Adjust the sound equalizer.
EXIT
VOL CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
User
DE F G MENU
0.1 0.5 1.5 5.0 10 kHz
1
2
3
4
5
6
2 3 4
5
1
DASP
AVL
Balance 0
Speaker
Sound
DE F G MENU
Surround MAXFlatMusicMovieSportsUser
Sound
DE F G MENU
DASP G
AVL
Balance 0
Speaker
46
TV MENU
TV M
ENU
Sound Menu Options
AUTO VOLUME LEVELER (AVL)
1
Press the MMEENNUU button and then DD // EE button to select the Sound menu.
Press the GG button and then DD // EE button to select AVL.
Press the GG button and then DD // EE button to select
On or Off.
Press the EEXXIITT button to return to TV viewing or press theMMEENNUU button to return to the previous menu.
AVL automatically keeps on an equal volume level even if youchange programs.
1
2
3
4
1
2 3
DASP
AVL
Balance 0
Speaker
Sound
DE F G MENU
OnOff
Sound
DE F G MENU
DASP
AVL G
Balance 0
Speaker
- The TV can receive MTS stereo programs and any SAP (Secondary AudioProgram) that accompanies the stereo program; if the broadcaster trans-mits one additional sound signal in addition to the original one.
- Mono: The primary language is heard from left and right speakers. Signal mode is mono.
- Stereo: The primary language is heard from left and right speakers. Signal mode is stereo.
- SAP: The secondary language is heard from left and right speakers in mono sound.
STEREO/SAP BROADCASTS SETUP
Press the MMTTSS button repeatedly. Each time you press MMTTSS
button, Mono, Stereo, or SAP appear in turn.
Press the EEXXIITT button to return to TV viewing.
1
2
EXIT SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
NOTE!GG Select mono sound mode if the signal is not clear or in poor signal reception areas.GG Stereo, SAP modes are available only if included on the broadcast signal.
TV M
ENU
47
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
BALANCE ADJUSTMENT
You can adjust the sound balance of speaker to the levels youprefer.
Press the MMEENNUU button and then DD // EE button to select the Sound menu.
Press the GG button and then DD // EE button to selectBalance.
Press the GG button and then FF // GG button to make desired adjustment.
Press the EEXXIITT button to return to TV viewing or press theMMEENNUU button to return to the previous menu.
1
2
3
4
1
1
2 3
DASP
AVL
Balance 0
Speaker
Sound
DE F G MENU
Sound
DE F G MENU
DASP
AVL
Balance R15 G
Speaker
48
TV MENU Sound Menu Options
TV M
ENU
You can adjust the internal speaker status.In Video, COMPONENT, RGB[PC], RGB[DTV] and HDMI mode,internal speaker audio or variable audio can be outputted eventhough there is no video signal.If you want to use your external hi-fi stereo system, turn off theinternal speakers of the set.
SPEAKER
Press the MMEENNUU button and then DD // EE button to select
the Sound menu.
Press the GG button and then DD // EE button to select
Speaker.
Press the GG button and then DD // EE button to select
On or Off.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
1
2
3
4
1
1
2 3
DASP
AVL
Balance 0
Speaker
Sound
DE F G MENU
OnOff
Sound
DE F G MENU
DASP
AVL
Balance 0
Speaker G
TV M
ENU
49
TV MENU Timer Menu Options
Press the MMEENNUU button and then DD // EE button to select the Timer menu.
Press the GG button and then DD // EE button to selectClock.
Press the GG button and then DD // EE button to set thehour.
Press the GG button and then DD // EE button to set the minutes.
Press the EEXXIITT button to return to normal TV viewing.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
You must set the time correctly before using on/off time function.
If current time setting is erased by a power failure or the set isunplugged, reset the clock.
CLOCK SETUP
1
2
3
4
5
1
2 3
Timer
DE F G MENU
- - : - - AM
Clock
Off timer
On timer
Auto off
Timer
DE F G MENU
Clock G
Off time
On time
Auto off
4
50
TV MENU
TV M
ENU
Timer Menu Options
Press the MMEENNUU button and then DD // EE button to select the Timer menu.
Press the GG button and then DD // EE button to select Off timer/On timer.
Press the GG button and then DD // EE button to select On.• To cancel On/Off timer function, select Off.
Press the GG button and then DD // EE button to set the hour.
Press the GG button and then DD // EE button to set the minutes.
FFoorr oonnllyy OOnn ttiimmeerr ffuunnccttiioonn
• VVoolluummee: Press the GG button and then DD // EE buttonto adjust volume level at turn-on.
• CChhaannnneell: Press the GG button and then DD // EE buttonto select the Channel.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
ON/OFF TIMER
The Off timer automatically switches the set to standby at thepreset time.
Two hours after the set is switched on by the on time function itwill automatically switch back to standby mode unless a buttonhas been pressed.
Once the on timer/off timer is set, these functions operate dailyat the preset time.
Off time function overrides On timer function if they are set bothto the same time.
The set must be in standby mode for the On timer to work.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
1
2
3
4
5
6
7
1
6
2
Timer
DE F G MENU
12 : 00 AM
Clock
Off timer
On timer
Auto off
Timer
DE F G MENU
Clock
Off timer G
On timer
Auto off
On
Off
Timer
DE F G MENU
Clock
Off timer
On timer G
Auto off12 : 00 AM
Vol. 8
Ch. TV 2
On
Off
3 4 5
TV M
ENU
51
If set to on and there is no input signal, the TV turns off automati-cally after 10 minutes.
AUTO OFF
Press the MMEENNUU button and then DD // EE button to select
the Timer menu.
Press the GG button and then DD // EE button to select
Auto off.
Press the GG button and then DD // EE button to select
On or Off.
Press the EEXXIITT button to return to TV viewing or press
the MMEENNUU button to return to the previous menu.
1
1
2
3
4
2 3
Timer
DE F G MENU
Clock
Off timer
On timer
Auto off
Timer
DE F G MENU
Clock
Off timer
On timer
Auto off G On
Off
You don’t have to remember to switch the set off before you goto sleep. The sleep timer automatically switches the set to stand-by after the preset time has elapsed.
SLEEP TIMER
Press the SSLLEEEEPP button repeatedly to select the number of minutes. The display ‘ -- -- -- ’ will appearon the screen, followed by 10, 20, 30, 60, 90, 120, 180 and 240.
When the number of minutes you want is displayed on the screen, the timer begins to count down fromthe number of minutes selected.
1
2
EXIT
VOL CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
NOTE!GG To view the remaining sleep time, press the SSLLEEEEPP button once.GG To cancel the sleep time, repeatedly press the SSLLEEEEPP button until the display ‘ -- -- -- ’ appears.GG When you switch the set off, the set releases the preset sleep time.
zz
zz
52
TV M
ENU
TV MENU Special Menu Options
LANGUAGE
The menus can be shown on the screen in the selected language.First select your language.
Press the MMEENNUU button and then DD // EE button to
select the Special menu.
Press the GG button and then DD // EE button to select
Language.
Press the GG button and then DD // EE button to select yourdesired language.
Press the EEXXIITT button to return to TV viewing or
press the MMEENNUU button to return to the previous menu.
1
2
3
41
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
Language
Key lock
ISM Method
Low Power
Set ID
Caption/Text
Demo
Special
DE F G MENU
TV M
ENU
53
TV MENU Special Menu Options
KEY LOCK
The TV can be set so that the remote control is needed to control it. This feature can be used to prevent unauthorized viewing.This set is programmed to remember which option it was last set toeven if you turn the set off.
Press the MMEENNUU button and then DD // EE button to selectthe Special menu.
Press the GG button and then DD // EE button to select Key lock.
Press the GG button and then DD // EE button to select On or Off.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
NOTE!GG In KKeeyy lloocckk ‘OO nn’, if the set is turned off, press the rr // II, IINNPPUUTT, CCHH DD // EE button on the set or
PPOOWWEERR, IINNPPUUTT, TT VV, CCHH ++//-- or NUMBER buttons on the remote control.
GG With the KKeeyy lloocckk OO nn, the display ‘KKeeyy lloocckk’ appears on the screen if any button on the frontpanel is pressed while viewing the set.
1
2
3
41
2 3
Special
DE F G MENU
OnOff
Language
Key lock
ISM Method
Low Power
Set ID
Caption/Text
Demo
Special
DE F G MENU
Language
Key lock G
ISM Method
Low Power
Set ID
Caption/Text
Demo
54
TV M
ENU
TV MENU Special Menu Options
ISM (IMAGE STICKING MINIMIZATION) METHOD
Press the MMEENNUU button and then DD // EE button to select the Special menu.
Press the GG button and then DD // EE button to select ISM Method.
Press the GG button and then DD // EE button to select either Normal, White wash, Orbiter or Inversion. If you unnecessary to set this function, set Normal.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
A frozen of still picture from a PC/video game displayed on thescreen for prolonged periods will result in a ghost image remainingeven when you change the image. Avoid allowing a fixed image toremain on the set's screen for a long period of time.
It’s not available to use this function in 26/32LC2R/32LC3Rmodels.
WWhhiittee wwaasshhWhite wash removes permanent images from the screen. NNoottee:: An excessive permanent image may be impossible toclear entirely with White Wash.
OOrrbbiitteerrOrbiter may help prevent ghost images. However, it is bestnot to allow any fixed image to remain on the screen. Toavoid a permanent image on the screen, the screen will moveevery 2 minutes.
IInnvveerrssiioonnThis is the function to invert the panel color of the screen.The panel color is automatically inverted every 30 minutes.
1
2
3
4
1
2 3
Special
DE F G MENU
Normal
White wash
Orbiter
Inversion
Language
Key lock
ISM Method G
Low Power
Set ID
Caption/Text
Demo
Language
Key lock
ISM Method
Low Power
Set ID
Caption/Text
Demo
Special
DE F G MENU
TV M
ENU
55
LOW POWER
This is the function to reduce the power consumption of the set.
It’s not available to use this function in 26/32LC2R/32LC3R models.
Press the MMEENNUU button and then DD // EE button to
select the Special menu.
Press the GG button and then DD // EE button to select
Low power.
Press the GG button and then DD // EE button to select
On or Off.
Press the EEXXIITT button to return to TV viewing or
press the MMEENNUU button to return to the previous menu.
1
2
3
41
2 3
Special
DE F G MENU
On
Off
Language
Key lock
ISM Method
Low Power G
Set ID
Caption/Text
Demo
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
Language
Key lock
ISM Method
Low Power
Set ID
Caption/Text
Demo
Special
DE F G MENU
56
CLOSED CAPTIONS
TV MENU Special Menu Options
TV M
ENU
2. An old, bad, or illegally recorded tape is being played.3. Strong, random signals from a car or airplane interfere with the TV
signal.4. The signal from the antenna is weak.5. The program wasn’t captioned when it was produced, transmitted,
or taped.
Closed captioning is a process which converts the audio portion ofa television program into written words which then appear as subti-tles on the television screen. Closed captions allow viewers to readthe dialogue and narration of television programs.
UUssiinngg CClloosseedd CCaappttiioonnssCaptions are the subtitles of the dialogue and narration of televisionprograms. For prerecorded programs, program dialogue can bearranged into captions in advance. Its possible to caption a live pro-gram by using a process called real-time captioning, which createscaptions instantly. Real-time captioning is normally done by profes-sional reporters using a machine shorthand system and computer
for translation into English.Captioning is an effective systemfor the hearing-impaired, and itcan also aid in teaching languageskills.
• The picture at left shows a typ-ical caption.
CCaappttiioonn TTiippss• Not all TV broadcasts include closed caption signals.• Sometimes TV stations broadcast four different caption signals
on the same channel. By selecting Mode1 to Mode2, you canchoose which signal you view. Mode1 is usually the signal with thecaptions, while Another mode might show demonstration or pro-gramming information.
• Your TV might not receive caption signals normally in the follow-ing situations.
• IIGGNNIITTIIOONN::Picture may flutter, drift, suffer from blackspots, or horizontal streaking. Usuallycaused by interference from automobileignition systems, neon lamps, electricaldrills, and other electrical appliances.
• GGHHOOSSTTSS::Ghosts are caused when the TV signal splitsand follows two paths. One is the directpath and the other is reflected off tall build-ings, hills or other objects. Changing thedirection or position of the antenna mayimprove reception.
• SSNNOOWW::If your receiver is located at the weak,fringe area of a TV signal, your picture maybe marred by small dots. It may be neces-sary to install a special antenna to improvethe picture.
FOLLOW ME
1. Poor reception conditions are encountered:
• You can also adjust Caption/Text in the Special menu.
Use the CCAAPPTTIIOONN button repeatedly to select your captionMode1, Mode2, Text1, Text2, Off.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
1
2
INPUTTVTV
INPUT
PIP CH- PIP CH+ PIP INPUT
DVD
ARC
PIP SIZE POSTION
VCR
POWER
CAPTION
TV M
ENU
57
XD DEMO
Use it to see the difference between XD Demo on and XDDemo off.
It’s not available to use this function in RGB[PC] mode.
Press the MMEENNUU button and then use DD // EE button to select the Special menu.
Press the GG button and then use DD // EE button to selectXD Demo.
Press the GG button to begin XD Demo.
To stop XD Demo, press the MMEENNUU button.
1
2
3
4
• X D D e m o
XD™Off XD™On
ExitMenu
1
2 3
Special
DE F G MENU
To start
Language
Key lock
ISM Method
Low Power
Set ID
Caption/Text
Demo G
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
Language
Key lock
ISM Method
Low Power
Set ID
Caption/Text
Demo
Special
DE F G MENU
58
AUTO CONFIGURE (RGB [PC] MODE ONLY)
TV MENU Screen Menu Options
TV M
ENU
Press the MMEENNUU button and then use DD // EE button toselect the Screen menu.
Press the GG button and then use DD // EE button to select Auto config..
Press the GG button to start Auto config..
• When Auto config. has finished, OO KK will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
If picture needs to be adjusted more after Auto adjustment in RGB (PC), you can adjust the Manual config...
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
Automatically adjusts picture position and minimizes imageshaking.
Although the image is still not correct, your set is functioningproperly but needs further adjustment.
AAuuttoo ccoonnffiigguurree
This function is for the automatic adjustment of the screen posi-tion, clock, and phase. The displayed image will be unstable for afew seconds while the auto configuration is in progress.
1
2
3
4
5
1
2 3
Auto config.
Manual config.
VGA Mode
ARC
Reset
Screen
DE F G MENU
Screen
DE F G MENU
To setAuto config. G
Manual config.
VGA Mode
ARC
Reset
TV M
ENU
59
MANUAL CONFIGURE
If the picture isn’t clear after auto adjustment and especiallyif characters are still trembling, adjust the picture phasemanually.
To correct the screen size, adjust Clock.
This function works in the following mode : RGB[PC],RGB[DTV], COMPONENT (480p/720p/1080i), HDMI(480p/720p/1080i).
It’s not available to use Phase, Clock function in RGB[DTV],COMPONENT (480p/720p/1080i), HDMI(480p/720p/1080i).
CClloocckk This function is to minimize any vertical bars or stripesvisible on the screen background. And the horizontalscreen size will also change.
PPhhaassee This function allows you to remove any horizontal noiseand clear or sharpen the image of characters.
Press the MMEENNUU button and then use DD // EE button to select the Screen menu.
Press the GG button and then DD // EE button to select Manual config..
Press the GG button and then DD // EE button to select Phase, Clock, H-position or V-position.
Press the FF // GG button to make appropriate adjustments.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
1
2
3
4
5
1
2 3 4
Auto config.
Manual config.
VGA Mode
ARC
Reset
Screen
DE F G MENU
Screen
Auto config.
Manual config. G
VGA Mode
ARC
Reset
Phase 50
Clock + 10
H-Position 0
V-Position 0
DE F G MENU
60
TV MENU Screen Menu Options
TV M
ENU
Press the AARRCC button repeatedly to select the desiredpicture format.
• 44::33Following selection will lead you to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.
• 1166::99 (Wide)Following selection will lead you to adjust the picture horizontally, in a linear proportion, to fill the entire screen(useful for viewing 4:3 formatted DVDs).
• HHoorriizzoonnChoose Horizon when you want to adjust the picture in anon-linear proportion, that is, more enlarged at both sides,to create a spectacular view.
• ZZoooomm11Following selection will lead you to view the picture with-out any alternation, while filling the entire screen. However,the top and bottom portions of the picture will be cropped.
• ZZoooomm22Choose ZZoooomm22 when you want the picture to be altered,both horizontally extended and vertically cropped. The picture taking a halfway trade off between alterationand screen coverage.
Press the EEXXIITT button to return to TV viewing or press the MMEENNUU button to return to the previous menu.
• You can also adjust ARC in the Screen menu.
INPUTTVTV
INPUT
PIP INPUT
DVD
ARC
EXIT SLEEP
MENU
PIP SIZE POSTION
VCR
POWER
ENTER
MEMORY/ERASE
CAPTION
MTS
PIP CH- PIP CH+
You can watch the screen in various picture formats; 4:3, 16:9,Horizon and Zoom1/2.
If a fixed image is displayed on the screen for a long time, that fixedimage may become imprinted on the screen and remain visible.
NOTE!
GG You can only select 44::33, 1166::99(Wide) in Component, RGB,HDMI mode only.
SETTING THE PICTURE FORMAT
1
2
Auto config.
Manual config.
VGA mode
ARC
Reset
Screen
DE F G MENU
Screen
DE F G MENU
4:3
16:9
Horizon
Zoom1
Zoom2
Auto config.
Manual config.
VGA mode
ARC G
Reset
1
2 3
TV M
ENU
61
To see a normal picture, match the resolution of RGB mode andselection of VGA/XGA mode.
This function works in the following mode: RGB[PC] mode.
Press the MMEENNUU button and then use DD // EE button to
select the Screen menu.
Press the GG button and then use DD // EE button to select
VGA mode (or XGA mode).
Press the GG button and then use DD // EE button to select
the desired VGA/XGA resolution.
Press the EEXXIITT button to return to TV viewing or press the
MMEENNUU button to return to the previous menu.
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
SELECTING WIDE VGA/XGA MODE
1
2
3
4
1
2 3
Auto config.
Manual config.
VGA mode
ARC
Reset
Screen
DE F G MENU
Screen
DE F G MENU
640x480
848x480
852x480
Auto config.
Manual config.
VGA mode G
ARC
Reset
62
TV MENU Screen Menu Options
TV M
ENU
This function operates in current mode.To initialize the adjusted value.
Press the MMEENNUU button and then DD // EE button to select the Screen menu.
Press the GG button and then DD // EE button to select Reset.
Press the GG button.
• You can initialize Position, PIP size, PIP position. (PIP sizeand PIP position are available to work in PIP mode only.)
INITIALIZING (RESET TO ORIGINAL FACTORY SETTINGS)
1
2
3
EXIT
VOL
MUTE
CH
SLEEP
MENU
1 2 3
4 5 6
7 8 9
ENTER
REVIEW
MEMORY/ERASE MTS
1
2 3
Auto config.
Manual config.
VGA Mode
ARC
Reset
Screen
DE F G MENU
Screen
DE F G MENU
To set
Auto config.
Manual config.
VGA Mode
ARC
Reset G
TV M
ENU
63
APPENDIX
RS-232C Setup
Connect the RS-232C input jack to an external control device (such as a computer or an A/Vcontrol system) and control the Monitor’s functions externally.Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.RS-232C connection cables are not supplied with the Monitor.
REMOTECONTROL IN
AUDIO IN(RGB/DVI)
RGB IN(PC/DTV) HDMI/DVI INHDMI/DVI IN
AUDIO OUTVARIABLE
RS-232C IN(CONTROL(CONTROL & SERVICE)
PC
EXTERNAL CONTROL DEVICE SETUP
Type of Connector; D-Sub 9-Pin Male
RGB IN(PC/DTV) HDMI/DVI IN
AUDIO OUTVARIABLE
RS-232C IN(CONTROL & SERVICE)No. Pin Name
1 No connection
2 RXD (Receive data)
3 TXD (Transmit data)
4 DTR (DTE side ready)
5 GND
6 DSR (DCE side ready)
7 RTS (Ready to send)
8 CTS (Clear to send)
9 No Connection
99
1 5
6
64
TV M
ENU
Communication Parameters
■ Baud rate : 9600 bps (UART)
■ Data length : 8 bits
■ Parity : None
■ Stop bit : 1 bit
■ Communication code : ASCII code
■ Use a crossed (reverse) cable.
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
PC TV
RXD 2 3 TXD
TXD 3 2 RXD
GND 5 5 GND
DTR 4 6 DSR
DSR 6 4 DTR
RTS 7 8 CTS
CTS 8 7 RTS
D-Sub 9 D-Sub 9
3-Wire Configurations(Not standard)
PC TV
RXD 2 3 TXD
TXD 3 2 RXD
GND 5 5 GND
DTR 4 6 DTR
DSR 6 4 DSR
RTS 7 7 RTS
CTS 8 8 CTS
D-Sub 9 D-Sub 9
Set ID- Use this function to specify a set ID number.
- Refer to ‘Real Data Mapping 1’. See page 68.
Press the MMEENNUU button and then DD // EE button
to select the Special menu.
Press the GG button and then use DD // EE button to
select Set ID.
Press the GG button and then use FF // GG button to
adjust Set ID to choose the desired monitor ID number.
• The adjustment range of Set ID is 1 ~ 99.
Press the EEXXIITT button to return to normal TV viewing.
EXIT
VOL
MUTE
CH
SLEEP
MENU
ENTER
REVIEW
MEMORY/ERASE MTS
1
2
3
4
Special
DE F G MENU
Language
Key lock
ISM Method
Low Power
Set ID G
Caption
Demo
1
APPENDIX
APPEN
DIX
65
Transmission / Receiving Protocol
Command Reference List
TTrraannssmmiissssiioonn
[Command 1] : First command to control the set.(j,k,mor x)
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99.
When selecting Set ID ‘0’, every connected the TV
is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~ 0x63)
on transmission/receiving protocol.
[DATA] : To transmit command data.
Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
OOKK AAcckknnoowwlleeddggeemmeenntt
The TV transmits ACK (acknowledgement) based on this for-
mat when receiving normal data. At this time, if the data is
data read mode, it indicates present status data. If the data is
data write mode, it returns the data of the PC computer.
EErrrroorr AAcckknnoowwlleeddggeemmeenntt
The TV transmits ACK (acknowledgement) based on this for-
mat when receiving abnormal data from non-viable functions
■ Connect your wired remote control to the Remote Control port on the TV.
2. Remote Control IR Codes
■ Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz
T1
Tc
IR CODES
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
APPEN
DIX
71
REMOTE CONTROL IR CODES
Code Function Note(Hexa)Code Function Note(Hexa)
0F TV R/C Button
0B INPUT R/C Button
08 POWER R/C Button (Power On/Off)
C4 POWER ON Discrete IR Code (Only Power On)
C5 POWER OFF Discrete IR Code (Only Power OFF)
60 PIP R/C Button
0E SLEEP R/C Button
38 Caption/Text R/C Button
0A MTS R/C Button
43 MENU R/C Button
79 ARC R/C Button
5B EXIT R/C Button
07 FF R/C Button
06 GG R/C Button
40 DD R/C Button
41 EE R/C Button
44 ENTER R/C Button
72 PIP CH- R/C Button
71 PIP CH+ R/C Button
61 PIP INPUT R/C Button
02 VOL + R/C Button
03 VOL - R/C Button
00 CH + R/C Button
01 CH - R/C Button
09 MUTE R/C Button
55 Memory/Erase R/C Button
10 ~ 19 Number Key 0 ~ 9 R/C Button
1E FCR R/C Button
1A REVIEW R/C Button
64 SIZE R/C Button
62 PIP: POSITION, R/C Button
E0 + R/C Button
E1 - R/C Button
72
APPENDIX
APPEN
DIX
PROGRAMMING THE REMOTE
Programming a code into a remote mode
Test your remote control.
To find out whether your remote control can operate the component without programming, turn on thecomponent such as a VCR and press the corresponding mode button (such as a DDVVDD or VVCCRR) on theremote control, while pointing at the component. Test the PPOOWWEERR and CC HH +/- buttons to see if the com-ponent responds properly. If not, the remote requires programming to operate the device.
Turn on the component to be programmed, then press the corresponding mode button (such as a DDVVDD orVVCCRR) on the remote control. The remote control button of desired device is lighted.
Press the MMEENNUU and MMUUTTEE buttons simultaneously, the remote control is ready to be programmed for thecode.
Enter a code number using the number buttons on the remote control. Programming code numbers for thecorresponding component can be found on the following pages. Again, if the code is correct, the device willturn off.
Press the MMEENNUU button to store the code.
Test the remote control functions to see if the component responds properly. If not, repeat from step 2.
The remote is a multi-brand or a universal remote. It can be programmed to operate most remote-control-lable devices of other manufacturers.
Note that the remote may not control all models of other brands.
■ Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted into wall power outlet?
■ Check your antenna direction and/or location.
■ Test the wall power outlet, plug another product’s power cord into the outletwhere the product’s power cord was plugged in.
■ This is normal, the image is muted during the product startup process. Pleasecontact your service center, if the picture has not appeared after five minutes.
■ Adjust Color in menu option.
■ Keep a sufficient distance between the product and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
■ Check for local interference such as an electrical appliance or power tool.
■ Station or cable product experiencing problems, tune to another station.
■ Station signal is weak, reorient antenna to receive weaker station.
■ Check for sources of possible interference.
■ Check antenna (Change the direction of the antenna).
■ Check to see if there is any object between the product and the remote controlcausing obstruction.
■ Are batteries installed with correct polarity (+ to +, - to -)?
■ Check the power control settings. Power interrupted
■ No broadcast on station tuned with Auto off activated.
APPEN
DIX
75
■ Press the VVOOLL ++//-- ((oorr VVoolluummee)) button.
■ Sound muted? Press MMUUTTEE button.
■ Try another channel. The problem may be with the broadcast.
■ Are the audio cables installed properly?
■ Adjust Balance in menu option.
■ A change in ambient humidity or temperature may result in an unusual noisewhen the product is turned on or off and does not indicate a fault with theproduct.
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you willhave your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarmwater and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and thenuse it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■ Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplugthe power cord to protect against possible damage from lightning or power surges.
CAUTION
1
2
APPEN
DIX
77
PRODUCT SPECIFICATIONS
26LC2R(26LC2R-MJ)
32LC2R(32LC2R-MJ)
MODELS
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
AC100-240V -50/60Hz, 1.3A, 130W
NTSC, PAL-M/N
VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125
75 ohm
Dimensions
(Width x Height x Depth)
Weight
Power requirement
Television System
Program Coverage
External Antenna Impedance
Environment condition
including stand
excluding stand
including stand
excluding stand
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
26.8 x 21.3 x 6.8 inches
681.0 x 542.0 x 172.0 mm
26.8 x 19.3 x 4.6 inches
681.0 x 490.8 x 119.0 mm
40.8 pounds / 18.5 kg
33.5 pounds / 15.2 kg
31.9 x 24.8 x 9.3 inches
811.0 x 630.0 x 235.0 mm
31.9 x 22.3 x 4.9 inches
811.0 x 566.8 x 123.5 mm
48.2 pounds / 21.9 kg
40.8 pounds / 18.5 kg
■ The specifications shown above may be changed without prior notice for quality improvement.
AC100-240V -50/60Hz, 1.5A, 150W
37.4 x 22.4 x 10.0 inches
924.0 x 570.0 x 254.0 mm
37.4 x 20.5 x 4.9 inches
924.0 x 520.0 x 123.5 mm
46.7 pounds / 21.2 kg
42.5 pounds / 19.3 kg
32LC3R(32LC3R-MJ)
78
PRODUCT SPECIFICATIONS
APPEN
DIX
■ The specifications shown above may be changed without prior notice for quality improvement.