Laser (Light Amplification by Stimulated Emission of Radiation) BY SUMITESH MAJUMDER
Dec 18, 2015
Laser (Light Amplification by Stimulated Emission of Radiation)
BY SUMITESH MAJUMDER
What is Laser? Light Amplification by Stimulated Emission of
Radiation
• A device produces a coherent beam of optical radiation by stimulating electronic, ionic, or molecular transitions to higher energy levels
• Mainly used in Single Mode Systems• Light Emission range: 5 to 10 degrees• Require Higher complex driver circuitry than LEDs• Laser action occurs from three main processes: photon
absorption, spontaneous emission, and stimulated emission.
Properties of Laser• Monochromatic Concentrate in a narrow range of wavelengths
(one specific colour).
• Coherent All the emitted photons bear a constant phase
relationship with each other in both time and phase
• Directional A very tight beam which is very strong and
concentrated.
Basic concepts for a laser
• Absorption
• Spontaneous Emission
• Stimulated Emission
• Population inversion
Absorption
• Energy is absorbed by an atom, the electrons are excited into vacant energy shells.
Spontaneous Emission
• The atom decays from level 2 to level 1 through the emission of a photon with the energy hv. It is a completely random process.
Stimulated Emission
atoms in an upper energy level can be triggered or stimulated in phase by an incoming photon of a specific energy.
Stimulated Emission
The stimulated photons have unique properties:
– In phase with the incident photon
– Same wavelength as the incident photon
– Travel in same direction as incident photon
Stimulated Emission
Laser Diode Optical Cavity• One reflecting mirror is at one end while the other end
has a partially reflecting mirror for partial emission• Remaining power reflects through cavity for amplification
of certain wavelengths, a process known as optical feedback.
• Construction very similar to the ELEDs.
Mirror Reflections
The operation of the Laser
The operation of the Laser
1E
2E
3E4E
The operation of the Laser
1E
2E
3E4E
absorption
The operation of the Laser
1E
2E
3E4E
Spontaneous emission
The operation of the Laser
Spontaneous emission
1. Incoherent light
2. Accidental direction
The operation of the Laser
1E
2E
3E4E
The operation of the Laser
1E
2E
3E4E
Stimulated emission
The operation of the Laser
Light: Coherent, polarized
The stimulating and emitted photons have the same:
frequency
phase
direction
How a Laser Works
Condition for the laser operation
If n1 > n2
• radiation is mostly absorbed absorbowane• spontaneous radiation dominates.
• most atoms occupy level E2, weak absorption
• stimulated emission prevails
• light is amplified
if n2 >> n1 - population inversion
Necessary condition: population inversion
E1
E2
Population Inversion
• A state in which a substance has been energized, or excited to specific energy levels.
• More atoms or molecules are in a higher excited state.
• The process of producing a population inversion is called pumping.
• Examples:
→by lamps of appropriate intensity
→by electrical discharge
E1
E2
• n1 - the number of electrons of energy E1
• n2 - the number of electrons of energy E2
2 2 1
1
( )exp
n E E
n kT
Boltzmann’s equation
example: T=3000 K E2-E1=2.0 eV
42
1
4.4 10n
n
Einstein’s relation
Probability of stimulated absorption R1-2
R1-2 = ()n1 B1-2 where spectral density is ()
& Einstein coeff. of absorbtion is B1-2
Probability of stimulated and spontaneous emission :
R2-1 = () n2B2-1 + n2A2-1
Einstein coeff. of stimulated and spontaneous emission are B2-1& A2-1
Assumption : For a system in thermal equilibrium, the upword and downword transition rate must be equal :
R1-2 = R2-1 n1 () B1-2 = n2 ( () B2-1 + A2-1) 2 1 2 1
1 1 2
2 2 1
/ =
1
A Bn Bn B
E1
E2
B1-2/B2-1 = 1
According to Boltzman statistics:
() = =
12 1
2
exp( ) / exp( / )n
E E kT h kTn
1)exp(
/
12
21
1212
kT
h
B
BBA
1)/exp(
/8 33
kTh
ch
3
3
12
12 8
c
h
B
A
Planck’s law
The probability of spontaneous emission A2-1 /the probability of stimulated
emission B2-1(:
1. Visible photons, energy: 1.6eV – 3.1eV.
2. kT at 300K ~ 0.025eV.
3. stimulated emission dominates solely when h/kT <<1!(for microwaves: h <0.0015eV) The frequency of emission acts to the absorption:
if h/kT <<1.
1)/exp()(12
12
kThB
A
1
2
1
2
12
12
211
122122 ])(
1[)(
)(
n
n
n
n
B
A
Bn
BnAnx
x~ n2/n1
Two-level Laser System
• Unimaginable
as absorption and stimulated processes neutralize one another.
• The material becomes transparent.
Two level system
absorption Spontaneous emission
Stimulated emission
h hh
E1
E2
E1
E2
h=E2-E1
Three-level Laser System
• Initially excited to a short-lived high-energy state .
• Then quickly decay to the intermediate metastable level.
• Population inversion is created between lower ground state and a higher-energy metastable state.
23 21
1.06 m 4
2τ 2.3 10 s
1 3.39 m 2 0.6328 m
3 1.15 m
100nsτ2 10nsτ
1
Three-level Laser System
Nd:YAG laser
He-Ne laser
Four-level Laser System
• Laser transition takes place between the third and second excited states.
• Rapid depopulation of the lower laser level.
Four-level Laser System
23
m 6943.01
m 6928.02
s7
310τ s3
2103τ
Ruby laser
Multimode Laser Output Spectrum
Longitudinal Modes
ModeSeparation
(Center Wavelength)
g(λ)
Lasing Characteristics• Lasing threshold is
minimum current that must occur for stimulated emission
• Any current produced below threshold will result in spontaneous emission only
• At currents below threshold LDs operate as ELEDs
• LDs need more current to operate and more current means more complex drive circuitry with higher heat dissipation
• Laser diodes are much more temperature sensitive than LEDs
Fabry-Perot Laser (resonator) cavity
Modulation of Optical Sources
• Optical sources can be modulated either directly or externally.
• Direct modulation is done by modulating the driving current according to the message signal (digital or analog)
• In external modulation, the laser is emits continuous wave (CW) light and the modulation is done in the fiber
Types of Optical Modulation
• Direct modulation is done by superimposing the modulating (message) signal on the driving current
• External modulation, is done after the light is generated; the laser is driven by a dc current and the modulation is done after that separately
• Both these schemes can be done with either digital or analog modulating signals
Direct Modulation
• The message signal (ac) is superimposed on the bias current (dc) which modulates the laser
• Robust and simple, hence widely used• Issues: laser resonance frequency, chirp, turn
on delay, clipping and laser nonlinearity
Laser Construction
• A pump source
• A gain medium or laser medium.
• Mirrors forming an optical resonator.
Laser Construction
Pump Source• Provides energy to the laser system
• Examples: electrical discharges, flashlamps, arc lamps and chemical reactions.
• The type of pump source used depends on the gain medium.
→A helium-neon (HeNe) laser uses an electrical discharge in the helium-neon gas mixture.
→Excimer lasers use a chemical reaction.
gain medium
• Major determining factor of the wavelength of operation of the laser.
• Excited by the pump source to produce a population inversion.
• Where spontaneous and stimulated emission of photons takes place.
• Example:
solid, liquid, gas and semiconductor.
Optical Resonator
• Two parallel mirrors placed around the gain medium.
• Light is reflected by the mirrors back into the medium and is amplified .
• The design and alignment of the mirrors with respect to the medium is crucial.
• Spinning mirrors, modulators, filters and absorbers may be added to produce a variety of effects on the laser output.
Laser Types
• According to the active material:
solid-state, liquid, gas, excimer or semiconductor lasers.
• According to the wavelength:
infra-red, visible, ultra-violet (UV) or x-ray lasers.
Solid-state Laser
• Example: Ruby Laser• Operation wavelength: 694.3 nm (IR)• 3 level system: absorbs green/blue
•Gain Medium: crystal of aluminum oxide (Al2O3)
with small part of atoms of aluminum is replaced
with Cr3+ ions.•Pump source: flash lamp •The ends of ruby rod serve as laser mirrors.
Ene
rgy
LASING
rapid decay
Ruby laser
Al2O3Cr+
How a laser works?
Ruby laser
First laser: Ted MaimanHughes Research Labs1960
Liquid Laser
• Example: dye laser• Gain medium: complex organic dyes, such
as rhodamine 6G, in liquid solution or suspension.
• Pump source: other lasers or flashlamp.• Can be used for a wide range of
wavelengths as the tuning range of the laser depends on the exact dye used.
• Suitable for tunable lasers.
Schematic diagram of a dye laser
dye laser
A dye laser can be considered to be basically a four-level system. The energy absorbed by the dye creates a population inversion, moving the electrons into an excited state.
Gas Laser• Example: Helium-neon laser (He-Ne laser)• Operation wavelength: 632.8 nm • Pump source: electrical discharge• Gain medium : ratio 5:1 mixture of helium and neon
gases
μm15.1μm6328.0μm39.3 321
He-Ne laser
Semiconductor laser
Semiconductor laser is a laser in which semiconductor serves as photon source.
Semiconductors (typically direct band-gap semiconductors) can be used as small, highly efficient photon sources.
Applications of laser
• 1. Scientific
a. Spectroscopy b. Lunar laser ranging
c. Photochemistry d. Laser cooling
e. Nuclear fusion
• 2 Military
a. Death ray
b. Defensive applications
c. Strategic defense initiative
d. Laser sight
e. Illuminator
f. Rangefinder
g. Target designator
Applications of laser
• 3. Medical
a. eye surgery
b. cosmetic surgery
Applications of laser
• 4. Industry & Commercial
a. cutting, welding, marking
b. CD player, DVD player
c. Laser printers, laser pointers
d. Photolithography
e. Laser light display
Applications of laser