MICRO-GASIFICATION Cooking applications for developing Countries Davide Caregnato
Mar 27, 2016
MICRO-GASIFICATION Cooking applications for developing Countries
Davide Caregnato
2
The stages of thebiomass combustion
Drying: (endothermic T<100°C) thermal moisture vaporization
Gasification: general process of converting a solid fuel into a gas (wood-gas), that can be combusted, and a solid residue, that is left behind.
Combustion: (highly exothermic T>700°C) complete oxidation of the products given by the previous phases
3
The gasification
Consists on 2 different stages:
Wood-gasification: pyrolysis of the wood (endothermic T>150°C), consists on a thermal degradation of the solid fuel in absence of an externally supplied oxidizing agent (carbonization). It is a process driven by heat and “char” is the solid residue left.
Char-gasification: oxidation of the hot char left by pyrolysis (exothermic 700<T<800°C). Is a process driven by oxygen and ashes are the solid residue left.
4
Combustion process
AUTOTHERMALHEAT
Pyrolysis
CharGasificationAshes
H2O Vapour
Wood-Gas
O2
USABLEHEAT
2
3
Process
Solid
Gas
Products
Reagents
Heat transfer
Legend:
CO2 H2O
Drying
Combustion
Dry BiomassBiochar
Fresh Biomass
4
1
5
3 T's
In order to have a complete and efficient combustion the 3 T's are fundamental:
TEMPERATURE must be high enough to ignite the fuel
TURBULENCE must be vigorous enough for the fuel constituents to be exposed to the oxygen of the air
TIME must be long enough to assure complete combustion
6
Traditional fuelconsumption
2.5 billions of people rely on woodfuels for most of their energy needs
Too often heating generation is given by simple three stone fires
7
Three-stone cooking fire
Drying, Pyrolysis, Gasification and Combustion occur simultaneously in an uncontrolled manner
3T's are too low and uneven in many reaction zones
Hundreds of millions of people still use this cooking method in third world Countries
8
Problems related with the usage of three-stone fire
High production of dangerous air pollutants like CO, Particulate, and smoke in general (due to incomplete combustion of many particles)
Accumulation of smoke and air pollutants inside the habitation
Very Low combustion efficiency
Low cooking efficiency given by huge heat dispersion
9
Effects on exposed people
Indoor Air Pollution (IAP) from biomass fuel is a high risk factor for the development of Chronic Obstructive Pulmonary Disease (COPD)
COPD is a major cause of chronic morbidity and mortality throughout the world
COPD is projected to be the fourth leading cause of death worldwide in 2030
Indoor Air Pollution causes 1.3 million deaths per year (especially women an children)
10
Cooking processes
11
Cooking pot shapes
12
Other consequences
Combustion inefficiency of the three stone fire causes a biomass fuel consumption larger than necessary which leads to:
Deforestation or other kinds of environment degradation due to the abuse of renewable resources
Consistent increase of the fuel collecting times and efforts
Negative effects given by traditional “slash and burn” technique
Soil degradation
13
Wood-gas stoves
A WGS consists of a micro-gasifier combustion unit and a heat-transfer unit
WGS allow a separation in space of the gas-burning zone from the gas-production zone
Pyrolytic WGS produce biochar as solid remaining after combustion
The technology needed to build an efficient WGS is very simple
WGS are very cheap and available even for very poor people
14
Substituting traditional fires with wood-gas stoves
Allows to burn efficiently agricultural residues and poor fuels like maize cobs, groundnut shells, palm oil fibres, palm oil kernels, rice husk, sawdust, etc..
Leads to a minor consumption of woodfuels preserving the environment from deforestation
Prevents people from indoor air pollution exposure
Improves soil fertility thanks to biochar
Represents an active free process of carbon-segregation
15
Wood-gas stoves benefits
OLD “SLASH AND BURN” TECNIQUE
NEW “SLASH AND CHAR” TECNIQUE
16
Micro-gasifier combustion unit
Micro-gasifier is the most important part of a WGS
It is a batch reactor, which gasifies a fixed fuel bed, and burns the produced gas apart
It can reach temperatures of 900-1000°C so it should be made of metal or a refractory material
There are many kinds of Micro-gasifier but the TLUD type is the most common and suitable for cooking applications
17
Top-Lit Up-Draft gasifier (TLUD)
Top-Lit: Fuel is ignited from the top
Up-Draft: Air and other gases draft proceed upward
Fuel is loaded as a fixed bed inside the reactor
18
TLUD's conceptualvariants
Draft type:
Natural Draft: gas flow is established naturally thanks to pressure and temperature gradient
Forced Draft (fan assisted): gas flow is forced through a fan
Secondary air inlet type:
Direct: gasifier consists of a single pipe
Hollow spaced: gasifier consists of 2 coaxial pipes
19
Single pipe vs2 coaxial pipes
FLAME AND BURNT GASES OUTLET
FLAME AND BURNT GASES OUTLET
SECONDARY AIR INLET
REACTIONCHAMBER
PRIMARY AIR INLET
HOLLOW SPACE
REACTIONCHAMBER
SECONDARY AIR
SECONDARY AIR INLET
PRIMARY AIR INLET
20
Natural-draft vs Forced-draft
FAN
VENTURI
REACTIONCHAMBER
REACTIONCHAMBER
EVENTUAL CHIMNEY
21
Operating principle Biomass gasifies progressively from the top to the
bottom of the fixed bed thanks to a Flaming-Pyrolysis (F-P) front moving downward
Primary inlet supplies the strictly necessary oxygen amount to sustain F-P front thanks to a partial combustion of the fuel
Wood-gas produced moves upward and after mixing with secondary air burns over the top of the reactor
The entire process is auto-thermal and it doesn't need any external energy supply
22
TLUD's combustion phases separation
DRYING
PYROLYSIS + PARTIAL COMBUSTION
HOT WOODGAS
RISING
COMBUSTION
UNBURNT BIOMASS
BIOCHAR
FLAME
FLAMING-PYROLYSIS FRONT
23
Flaming-Pyrolysis front
Is the reaction zone where simultaneously occur Partial Combustion and Pyrolysis
The wood-gas is produced in this zone
Thanks to its oxidative exothermic component it provides the heat needed by Pyrolysis and Drying
In this zone fuel assume a bright red colour typical of oxidative reactions
24
F-P front shape and movement
It has the shape of a thin disk extended along the entire horizontal section of the chamber (its thickness depends on primary air amount, fuel calorific value and fuel bed porousness)
F-P front moves downward from the top to the bottom of the fuel packed column
F-P front velocity varies from 3 to 20 mm per minute depending on primary air amount, fuel calorific value and fuel bed porousness
25
Pre-heated air
Hot wood-gas
Gas flow
Fresh air
Legend:WOOD-GAS + SECONDARY AIR MIXING
ZONE
WOOD-GAS PRODUCTION
ZONE
26
AUTOTHERMAL HEAT GENERATION
USABLE HEATGENERATION
Temperature gradient
600-850
T [°C]
20-150
350-600
700-1100
27
Fuel container sizing Diameter of the fuel container (D):
gasifier power is proportional to the surface of fuel available for oxygenation (heating power is proportional to D²)
Length of the fuel container (H): process duration is proportional to the length of the fuel column
Typical gasifier dimensions for cooking purpose are: D=10-15 cm, H=20-30 cm (producing a power output of about 2-5 kW and a duration of 1-2 hours depending on fuel type)
28
Primary air inlet
Consists of a series of holes placed at the bottom of the fuel container
It must provide at least the minimum necessary amount of air to sustain the F-P front
It should be adjustable to allow the variation of the primary air amount (more oxygen from the primary causes an increase of the generated power)
29
Secondary air inlet
There are many possible different shapes suitable for the secondary air inlet depending on reactor features
It has to ensure a good mixing of secondary air and the hot wood-gas rising from the fuel
It must carry as air as possible in the mixing zone in order to grant a complete combustion of the burning gases (at least 6 times more than the primary)
30
Section of 2 examples of secondary air inlets
Legend:
Secondary air
SECONDARY AIR HOLES
HOLLOW SPACE
OUTER COAXIAL
CYLINDER
SECONDARY AIR BAFFLES
31
Gasifier's top
The top constriction is important to convey all the outgoing gases and to allow a good mixing with the second air, giving stability to the flame (that is necessary to prevent interruptions of the upward gas flow)
Diameter of the top hole should be about 0,6D
0,6D
D
CAP
32
Feedstock requirements Fuel bed has to be porous enough to allow air to pass
through the space between the fuel particles
Particles diameter should be at least 3mm and should not be more than 20mm depending on biomass features
In most cases fuel is not naturally sized for a gasifier so it has to be previously prepared by resizing
Moisture content exceeding 20% will reduce efficiency of combustion and in many cases can stop the burning process
33
Biochar It is the residual solid product of the process
It is a kind of very porous lightweight black carbon
Biochar residual is about 15-20% of the weight of the starting loaded biomass
At the end of the process the flame goes out spontaneously but to prevent char gasification is necessary to cool it down or to seal it in the absence of oxygen
34
Emissions Little smoke is produced during the ignition phase while
after the end of the process consistent amount of tarry smoke is produced for several seconds
During the steady condition smoke is totally absent
Measuring CO is indicative of all hydrocarbon's unburnt species (including particulates)
CO emissions varies from 60 mg/m³ to 200 mg/m³ (compared to 11% of oxygen content), 10 times less than a traditional stove
35
Testing stoves atUniversity of Udine
Many tests were made in order to establish a link between stove design and emissions.
Tests features:
Stoves loaded with wood pellets were placed inside the combustion chamber of a modified boiler which convoyed all the produced gases in a chimney where measuring instruments were placed
Instruments measured CO,O2, CO2, HnCm, NOx, SOx
36
Some importantdeductions 1
Placing a small chimney at the top of the gasifier increases the stove power and reduces the ignition time but at the same time increases CO emissions
Primary air control is important to reduce ignition time (providing more air at the beginning) and to reduce emissions (providing less air than possible during the steady condition time)
37
Some importantdeductions 2
Primary air inlet holes should be made as lower as possible
A small metallic sectional net should be placed a few centimetres above the primary air inlet
Heat transfer unit design is very important to contain emissions
Top constriction should be horizontal to create a good turbulence in the mixing zone
38
Advantages given bymicro-gasification
Simple technology and low costs of production
High combustion efficiency with low fuel consumption
Very low emissions
Possibility to use poor biomass or agricultural residues as fuel
Possibility to save biochar for many purposes
Stable combustion process during a long time (even 2 hours with no human needed intervention)
39
Problems connected withmicro-gasification
Often different types of fuels needs different gasifier features
Sometimes fuel size is not immediately suitable and it needs preparation (it can take several minutes)
At the end of the process the stove produces a toxic tarry smoke for several seconds
To reload the stove with a new fuel charge is necessary to stop the process and repeat the ignition
Producing biochar not all the calorific value of the fuel is exploited
40
Next steps
Study a new type of heat transfer unit with the aim of produce fewer emissions than possible
Do many tests on emissions with different types of fuel
Improve the knowledge of the needs of rural target populations
Study the stoves behaviour directly on the field
Project a versatile stove which can be adaptable for a wide range of different fuel types
41
Thank you!