Operation Manual Fiber Optic Illuminator Model 21AC Model 21DC
Op
erat
ion
Man
ual
Fiber OpticIlluminator
Model 21ACModel 21DC
Warning
This symbol is intended to alert
the user to the presence of uninsulat-
ed “dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions to the literature accom-
panying the appliance.
Important
This equipment has been tested and
found to comply with IEC 61010-1
and UL3101-1 as an Overvoltage
Category II: (local level, small
appliances, portable equipment, etc.
with smaller transient overvoltages
than Overvoltage Category III.)
Pollution II.
Caution
You are cautioned that any change
or modifications not expressly
approved in this manual could
void your authority to operate
this equipment.
Precautions
On Power Sources
• Before operating the product,
check that the operating voltage
is identical to your local power
supply. See specific descriptions
for operating voltages.
• This unit is not disconnected from
the AC power source as long as it
is connected to the wall outlet,
even if the unit itself has been
turned off.
• To disconnect the AC power cord,
grasp the plug itself; never pull
the cord.
• One blade of the plug is wider
than the other for the purpose
of safety and will fit into the wall
outlet only one way. If you are
unable to fully insert the plug into
the outlet, contact Techniquip.
• AC power cord must be replaced
with IEC compatible cord.
On Operation
• Before connecting to fiber optic
components, be sure that all
power connections are secure.
On Cleaning
• Clean the cabinet, panel and
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder or
solvent such as alcohol or benzine.
Fiber OpticIlluminator
Model 21AC
If you have any questions or problems concerning your product,
please consult Techniquip.
For Customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG
WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS
THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
Owners Record
The model and serial number are located on the bottom of the unit. Record the
serial number in the space provided below. Refer to them whenever you call
upon your Techniquip dealer regarding this product.
Model Number
__________________________
Serial Number
__________________________
iii
Contents
MODEL 21ACGetting Started 1
Unpacking 1
Hookup Overview 1
Description 1
Illuminator Descriptions (Front Panel) 1
Illuminator Descriptions (Rear Panel) 2
Lamp Replacement 3
Specifications 4
Model Codes 5
21
Illuminator Descriptions (Rear Panel)
1. T-slot mounting for #1/4 - 20 or M6 hexhead fastener;both sides (#10 - 32 or M5 barnut optional)
2. IEC inlet with line filtering (power cable input)3. Operating voltage label:
Illuminator Descriptions (Rear Panel)
DescriptionGetting Started
Unpacking - MODEL 21AC
Check that you received all items on the packing list.
Hookup Overview
The Model 21AC Illuminator allows you to connect and control avariety of fiber optic components. To learn the locations and namesof important connections see “Illuminator Descriptions” beginningon this page below.
Before You Get Started
• Turn off the power to the Model 21AC Illuminator beforemaking any connections.
• Do not connect the AC power cord to the local powersupply until the connections are completed to the Model21AC Illuminator.
• Be sure to make connections firmly.• Be sure that the Model 21AC operating voltage matches
the “local” power supply.
Illuminator Descriptions (Front Panel)
1. Variable intensity controller (0 to 100%).2. On/Off rocker switch.3. Front panel fasteners (2X)4. Lamp module.5. V-port with T-handle retainer
43
Lamp Replacement Instructions
1. To replace the lamp, shut off the power and remove thepower cord from the AC outlet. To disconnect the ACpower cord, grasp the plug itself; never pull the cord.
2. Located on the lamp access panel, manually loosen thefront panel fasteners.
3. With front panel released, remove the lamp module fromthe unit.Use caution; fan blades are accessible while lampmodule is removed.
4. Allow sufficient time for the unit to cool. CAUTION:Lamp and surfaces may be extremely hot!
5. Remove the lamp from the socket and place in a safe area.
6. Insert the replacement lamp into the socket; pressingfirmly to ensure that pins are fully seated.
7. Close the access panel.
8. Secure the lamp access panel by manually tightening the front panel fasteners.
On Safety
Should any solid object or liquid fall into the assembly while accesspanel is open, have it checked by qualified personnel before operating.
Lamp Replacement Specifications
Specifications
EnvironmentalIntended for indoor use onlyOperating temperature: -4 to 104°F (-20° to 40°C)Humidity range: 0 to 80%; non-condensingPollution degree: 2
Electrical (all units)Operating frequency: 60 Hz (110 VAC) or 50 Hz (220VAC)Power consumption: 180 watts at full light intensityPower requirements: 110 VAC; 60 Hz
220 VAC; 50 HzLamp adjustment range: 0 to 100%Color temperature: 3200K at maximum intensity
(assuming standard EKE lamp)Lamp life: 250 to 10,000 hours
PhysicalMass (approx.): 4.5lbs. (2.04kgs)
Replacement Parts
Lamp ReplacementLamp Type: 150W EKE, 3250K (#20094145)*
150W EKE-HC, 4200K (#20094142)150W EJV, 3400K (20094143)
* Standard lamp type provided with illuminator.
Fuse ReplacementFuse Type: 3.15A 250V, 5x20mm (#02610014)
5
ModificationsMaterial TypeLamp TypeLamp Module (nosepiece)Cord SetInput VoltageModel
Model Codes
Model 21AC Matrix
21AC 1 K 1 00 X -XXX
Model: 21AC Model 21AC
Input Voltage: 1 110 VAC; 60 Hz2 220 VAC; 50 Hz
Cord Set: A Euro/Shuko H IsraelC Australia I ItalyD United Kingdom K North AmericaE Denmark L SwitzerlandF France/Belgium R RussiaG India X No Plug
Lamp Module: 1 Ø1.0” (25.4mm) thru2 Ø0.625” (15.88mm) V-port
Lamp Type: 00 EKE, 3250K (standard)01 EKE-HC, 4200K (high color temperature)02 EJV, 3200K (high output)
Material Type: X Standard material finish
Modifications: To Be Determined (consult factory)
Fiber OpticIlluminator
Model 21DC
87
Unpacking - MODEL 21DC
Check that you received all items on the packing list.
Hookup Overview
The Model 21DC Illuminator allows you to connect and control avariety of fiber optic components. To learn the locations and namesof important connections see “Illuminator Descriptions” beginningon this page below.
Before You Get Started
• Turn off the power to the Model 21DC Illuminator beforemaking any connections.
• Do not connect the AC power cord to the local powersupply until the connections are completed to the Model21DC Illuminator.
• Be sure to make connections firmly.• Be sure that the Model 21DC operating voltage matches
the “local” power supply.
Illuminator Descriptions (Front Panel)
1. Variable intensity control knob (0 to 100%).2. Power and lamp life indicators3. Front panel fasteners (2X)4. Lamp module.5. V-port with T-handle retainer
Getting Started /Description
MODEL 21DCGetting Started 8
Unpacking 8
Hookup Overview 8
Description 8
Illuminator Descriptions (Front Panel) 8
Illuminator Descriptions (Rear Panel) 9
Lamp Replacement 10
Specifications 12
Model Codes 13
Contents
109
Illuminator Descriptions (Rear Panel)
1. T-slot mounting for #1/4 - 20 or M6 hexhead fastener;both sides (#10 - 32 or M5 barnut optional)
2. IEC inlet with line filtering (power cable input)3. Operating voltage label:
4. DB-9 connector for remote operation
Description
1 = Internal 1mA, 5VDC output
2 = Secondary common (same as 7)3 = Lamp intensity control4 = Ties to common to engage
supply programming5 = No connection
6 = External shut off/interlock(external 5VDC/10mA will shut off lamp)
7 = Secondary common (same as 2)8 = Chassis ground9 = Lamp error signal
Lamp Replacement
Intensity Control
• Pin 4 activates remote operation when tied to common(pin 2 or 7). Note: Front panel control is disengaged during remote operation.
• Intensity level is controlled by Pin 3 by supplying a 0-5DC signal
• The internal voltage from Pin 1 may be used in conjunction with a remote potentiometer to vary intensitythrough Pin 3.
Remote On/Off
• Unit power, including the lamp, is controlled by Pin 6.• An external isolated signal (5VDC, 10mA) will shut off
power to the lamp. Power is restored to the lamp byremoving the 5VDC signal from Pin 6 (open).
Lamp Error Signal
• Pin 9 is the lamp error signal output. If Pin 9 is at 5V, thelamp is okay. If Pin 9 is at 0V, the halogen lamp will burnout in the near future, or it is burnt out, or there is nolamp in the lamp module. Pin 9 is at 5V when the LampLife indicator is unlit. Pin 9 is 0V when the Lamp Life LEDindicator is lit.
Illuminator Installation and Mechanical Dimensions
1211
Lamp Replacement Instructions
1. To replace the lamp, shut off the power and remove thepower cord from the AC outlet. To disconnect the ACpower cord, grasp the plug itself; never pull the cord.
2. Located on the lamp access panel, manually loosen thefront panel fasteners.
3. With front panel released, remove the lamp module fromthe unit.Use caution; fan blades are accessible while lampmodule is removed.
4. Allow sufficient time for the unit to cool. CAUTION:Lamp and surfaces may be extremely hot!
5. Remove the lamp from the socket and place in a safe area.
6. Insert the replacement lamp into the socket; pressingfirmly to ensure that pins are fully seated.
7. Close the access panel.
8. Secure the lamp access panel by manually tightening the front panel fasteners.
On Safety
Should any solid object or liquid fall into the assembly while accesspanel is open, have it checked by qualified personnel before operating.
Lamp Replacement Specifications
Specifications
EnvironmentalIntended for indoor use onlyOperating temperature: -4 to 104°F (-20° to 40°C)Humidity range: 0 to 80%; non-condensingPollution degree: 2
ElectricalPower consumption: 180W (Power factor corrected for CE)Power requirements: 90-254 VAC; 47-63 HzLamp adjustment range: 0 to 100%Color temperature: 3200K at maximum intensity
(assuming standard EKE lamp)Lamp life: 250 to 10,000 hoursAgency approvals UL 1950, CSA, CE, TUV & FCC
(Pending)
PhysicalMass (approx.): 4.5lbs. (2.04kgs)
Replacement Parts
Lamp ReplacementLamp Type: 150W EKE, 3250K (#20094145)*
150W EKE-HC, 4200K (#20094142)150W EJV, 3400K (20094143)
* Standard lamp type provided with illuminator.
Fuse ReplacementFuse Type: 3.15A 250V, 5x20mm (#02610014)
13
ModificationsMaterial TypeLamp TypeIris ModuleLamp Module (nosepiece)Cord SetInput VoltageModel
Model 21DC Matrix
Model: 21DCModel 21DCNote: All options are universal input (90-254VAC; 47-63Hz) and include 0-5V analog control capabilities.
Options: U Standard DC regulated operationP DCU w/PC interface (RS232)S DCU w/optical loop feedback, no PC interfaceL DCU w/optical loop feedback and PC interface
Cord Set: A Euro/Shuko K North AmericaC Australia L SwitzerlandD United Kingdom Z North AmericaH Israel X No Plug
Lamp Module: 1 Ø1.0” (25.4mm) thru2 Ø0.625” (15.88mm) V-port3 Ø1.0” (25.4mm) V-port for use with/IR & color filter4 Ø1.0” (25.4mm) V-port w/2 Hz shutter
Lamp Type: 0 EKE, 3250K (standard)1 EKE-HC, 4200K (high color temperature)2 EJV, 3200K (high output)
Material Type: X Standard material finish
Modifications: To Be Determined (consult factory)
21DC L K 1 0 0 -X ––––
Model Codes
E:MAIL
Chuck Mathewson [email protected] Grauer [email protected] Wensley [email protected]
PHONE
Toll Free 888-414-0789International 1-925-251-9030
Fax
925-251-0704
MAILING
Street: 5653 Stoneridge Dr., Suite 101, Pleasanton CA 94588Mailing: PO Box 3310, Danville, CA 94526
Warranty
TechniQuip warrants this product to be free from defect in materialand workmanship for a period of 12 months following original purchase. This warranty excludes any product which may havebeen misused, neglected, damaged, or altered – including non-factory authorized repairs. TechniQuip’s obligations under this warranty are limited to the repair, replacement, or reimbursement of the product only, and in no event is TechniQuip liable for any consequential or special damages, or any cost related to transportation, installation, or any other cost related to a warranted product.
5653 Stoneridge Drive #101Pleasanton, CA 94566
Phone: 925-251-9030 Fax: 925-251-07041-888-414-0789 (toll-free)
Version A04.15.06