-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Subject: Firmware Upgrade Model KM/CS-3035/4035/5035 Updated
Machine Serial Numbers: N/A
Details of Changes
Item Remark 1 Reducing developing
drive time The developing drive time is reduced to prevent a
line that may occur on the developing sleeve.
2 A measure to prevent a dirty image
The following changes are made: - Correcting the leading edge
transfer ON timing
(target is within 1mm from edge of the paper target for within
2mm)
- Change element of the transfer cleaning BIAS (-) at non paper
feeding -30 -10
- Correcting the leading edge transfer BIAS adjustment value -63
-30
3 A measure for a
fixing error when feeding post cards.
There may be the possibility of a fixing failure with post card
printing before the MFP becomes stabilized, after power ON, during
warm-up after the cover open/close or during warm-up from sleep
mode/pre-heat mode. This is corrected.
Direction of paper route
Firmware Information Type Program No. Check SUM VER. Remarks
MAIN 2FGS1015S BD73 166 Upgraded MMI 2FGS2030E 14AB 198 MMI(BA)
2FGS2015L C4B4 198 For new BAM SPEC LANGUAGE A 2FG29337K 46C1 25
For KMA LANGUAGE BRA 2FGS2022D F9B5 8 For KMA Portuguese
When upgrading firmware or replacing board etc., please upgrade
each firmware (MAIN, MMI, LANGUAGE) to the latest version posted on
KMAconnect.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Main Firmware is updated to Version 164, Level
5Q
The LSU is changed from the LK-700 to the LK-710 due to
discontinuation of the polygon motor production for the LSU by its
manufacturer. As a result of this change, firmware is modified to
enable you to switch the setting for old/new LSU in maintenance
mode U274 (Setting the LSU type). An instruction sheet is included
with the LK-710 instructing you to change the setting in
maintenance mode U274 when the LK-710 is installed. Content of
Modification 1. Support for LK-710
Firmware is changed so the setting in maintenance mode U274 can
be set for the LK-710. (ADJUST DATA: LSU type setting 0 ~ 3) is
changed to "3", (Initial setting is "2". The "0 ~ 2" setting is for
the LK-700)
If the LK-710 is installed without changing the maintenance mode
value, approximately 15% reduction may occur in the main scanning
direction. Identifying LSU To identify the LK-700) and LK-710,
check the first three (3) digits of the bar code number on the bar
code label. LK-700 : GCE (First 3 digits of individual production
number) LK-710: KDF (First 3 digits of individual production
number)
Parts Information
Ref. No. Old P/N New P/N Description Q'ty (Old/New)
Interchangeability
1 302BL93142 2BL93142
302GR930912GR93091
LK-710 1/1 Y/N
2 302GR93091
2GR93091 302GR93092
2GR93092 LK-710 1/1 Y/Y
* The instruction handout is not packed together with the LK-710
P/N 2GR93091. It is packaged with LK-710 P/N 2GR93092.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Firmware Information
(KM-3035/4035/5035)
Type Program No. Check SUM Version Remarks MAIN 2FGS1015Q 9D2D
164 Updated MMI 2FGS2030E 14AB 198
LANGUAGE A 2FG29337K 46C1 25 LANGUAGE
BRA 2FGS2022D F9B5 8 Portuguese in
South America
Please upgrade each firmware (MAIN, MMI, LANGUAGE, etc.) to the
latest versions posted on KMAconnect.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Main Firmware has been updated to Version
158
Firmware Information
Type Program No. Check SUM Version Remarks MAIN 2FGS1015L 80E6
158 Updated MMI 2FGS2030C 52B2 189
LANGUAGE A 2FG29337K 46C1 25 LANGUAGE BRA 2FGS2022D F9B5 8
Portuguese
Please upgrade each firmware (MAIN, MMI, LANGUAGE) to the latest
version whenever upgrading the firmware and/or replacing the board,
etc.
1. Measure for a problem that may occur as a result of
Thermostat being switched switch to an OFF condition. (Adding
time-out to the fixing stabilizing operation) (Problem)
If the main power is turned OFF while the thermistor temperature
remains less than 110C and then turned back ON, the stabilization
drive may keep running and the machine may not be stabilized. (A
"Please wait" message remains on the message display.)
The firmware is modified so after three (3) minutes of driving,
a time-out will occur. Precaution: The Fan located above the Bypass
Tray pulls in the air to cool the inside of the machine. If the Fan
is removed and reinstalled incorrectly it will blow air out or if
it fails to operate, the surrounding temperature of Thermostat
rises, causing the Thermostat to switch to an OFF condition.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Check if the Fan located over the Bypass Tray is working
correctly.
1. Check if air is blowing out of the machine. If so, refit the
Fan to its correct orientation so air is pulled into the machine.
2. If the Fan is not rotating, please replace the Fan or inspect
the connector and/or wiring.
2. Changing the amount of slack in the original at registration
during the switchback in SRDF-2 in duplex mode (Measure for skewed
original feed in duplex mode) The amount of slack at registration
during the original switchback operation is changed to the optimum
value for each size of original. [Waiting time at registration]
(Old) 150msec (for all sizes) (New) 30-cpm machine :
A5T/B5T/5.5x8.5/8.5x14/8.5x11 185msec : Other than above 195msec
40-cpm machine : A5T/B5T/5.5x8.5/8.5x14/8.5x11 190msec : Other than
above 200msec
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes
Firmware Information
Type Program No. Check SUM
Ver. Remarks
MAIN 2FGS1015K 803A 157
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Change to "Machine Used Circumstances List" (U960)
The value is displayed in hexadecimal numeral and last four
restart data appears on the List. (Main data: Thermistor
temperature, temperature/humidity conditions, restart
circumstances, etc.) *** The data above remains on the List for
each restart performed even if no C6050 triggers.
When visiting the end user whose machine was updated with the
new firmware and they experienced C6050 in the past, please output
the List and notify the Diagnostic Center.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes
Details of changes
Item Contents FIRM
1 Reducing the aging time after finishing copying (Measure for
the appearance of a white line.)
Change as follows to reduce the aging time after finishing
copying. Old) When the total number of sheets has exceeded 50,
after the power source is turned on, the aging process is performed
for about 10 seconds every time when finishing copying New) Only
when continuously copying more than 50 sheets, aging is performed
for about 10 seconds after finishing copying.
MAIN
Firmware Information Type Program No. Check SUM VER. Remarks
MAIN 2FGS1015J F4E0 153 newly upgraded MMI 2FGS2030B AD5B 180
LANGUAGE A 2FG29337K 46C1 25 For KMA LANGUAGE BRA 2FGS2022D F9B5 8
For KMA Portuguese When upgrading firmware or replacing board etc.,
please upgrade 3 types of firmware (MAIN, MMI and LANGUAGE) to the
latest versions.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes MMI Firmware is upgraded as follows.
Firmware Information
Type Program No. Check SUM Ver. Remark
MAIN 2FGS1015H 671A 152 MMI 2FGS2030B AD5B 180
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Continued 4 In the Scanner function,
default cursor position is changed for letter input to change
file name, etc. (Change back to original position.)
[Background]
With the previous firmware upgrade (*1) to support NSI/FTP, it
is changed so the cursor comes before the beginning of letter input
in default as a newly added menu allows more letters to be input
than before. (When the number of letters exceeds "32", the letter
entry field scrolls down.)
When the screen is switched to a file name input screen to
change the file name, etc, the cursor ("I") appears in front of
letters that are different from the way it used to be and it is not
user-friendly. The following change is carried out. Example: [[ "I"
Scan001_ ]] (Modification) Original letter input menu: The cursor
appears at the end of letters in default.
(Change back to the original location.) FTP/NSI related letter
input menu: Basically, the cursor appears at the beginning of
letters in default. (In some cases, at the end of letters.)
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of changes
No Item Remarks FIRM
1 Measures for a problem where black spots might occur due to
image blur (Changing the transfer "OFF" timing) Adding the
maintenance mode of U129 (Setting transcription timing)
[Phenomenon] There is a possibility that black spots might occur
on the copied image due to an image blur. (This phonomenon may
occur in a high temperature and humidity environment after turning
the power source of the machine ON when it has been OFF for a long
time.) [Cause] To keep the transfer performance of the trailing
edge of paper, even after the trailing edge of paper passes through
the nip of transfer roller, transfer bias is in an "ON" condition.
However, due to a change of resistance caused by the stains on the
transfer roller, there is a possibility that the electrical
discharge to drum might occur. [Change] The transfer "OFF" timing
(the time from the moment the registration switch is turned off)
has been changed so that the transfer bias is within the length of
paper feeding.
KM-3035 325msec 260msec KM-4035/5035 260msec 190msec
----------------------------------------------------------------------------------------------
[Notes] By the change above, there is a possibility that transfer
image might be skipped or transfer misalignment might occur within
the imperfect image area that is around 3mm from the trailing edge.
For that reason, the following additional maintenance mode is newly
added for the user that requests the previous control.
Adding the maintenance mode U129 (Setting transcription timing)
[MODE 0]: New transfer OFF timing (Default value) [MODE 1]: Old
transfer OFF timing
MAIN
MMI
MMIBA
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
(Continued) 2 Measures for the
occurrence of a paper JAM in which case mixed size of originals
are fed at a time using DF-71
When 2 sheets of A3 and A4 size paper is set (A4 size papers are
overlaid on A3 size paper) in the auto size selection/continuous
scanning mode, if the copy is started, after one sheet of A4 size
paper is stocked in the middle tray, the A4 size paper is output to
the eject tray. Next, although the other sheet of A4 size paper is
stock in the middle tray, the A4 size paper is not ejected and
remains in the middle tray. The remained A4 size paper hits against
the A3 paper secondly conveyed to the middle tray and paper JAM
occurs. Therefore the problem is corrected.
MAIN
3 Measures for a problem with cassette 2 when turning off/on the
main switch
If the main switch is repeatedly turned off/on several times,
cassette 2 might be out of order and the following phenomenon might
occur. Therefore the problem is corrected. Even if paper is stocked
in cassette 2, the message of paper empty is displayed. If the
cassette 2 is selected, though the cassette is set, the message
"Set cassette" is displayed.
MAIN
4 Measures for the occurrence of a paper JAM when processing 3
sheets of single-sided originals in duplex mode on KM/CS-5035
If 3 sheets of single-sided originals are processed in duplex
mode using the inner finisher on a KM/CS-5035, a paper JAM81
occurs. Therefore the problem is corrected.
MAIN
Firmware Information
Type Program No. Check SUM Version Remarks
MAIN 2FGS1015H 671A 152 New upgrade MMI 2FGS2030A (*) 3BF3 177
New upgrade LANGUAGE A 2FG29337K 46C1 25 For KMA spec.
LANGUAGE BRA 2FGS2022C 8FEA 7 Portuguese for KMA (*): Former
Program No.: 2FG2932MZ, Note: The entire sequence has been changed.
When upgrading firmware or replacing board etc., please upgrade 3
types of firmware (MAIN, MMI and LANGUAGE) to the latest version at
the same time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes
Firmware Information
Type Program No. Check SUM Version MAIN 2FGS1015G 82B6 148 New
upgrade MMI 2FG2932MZ 2F4C 174 New upgrade LANGUAGE A 2FG29337K
46C1 25 For KMA spec. New upgrade LANGUAGE BRA 2FGS2022C 8FEA 7 For
KMA Portuguese spec.
When upgrading firmware or replacing board etc., please upgrade
3 types of firmware (MAIN, MMI and LANGUAGE) to the latest version
at the same time. Details of changes
Item Remarks Firmware 1 Preventing the occurrence of
service call C6050 (Abnormally low fixing unit thermistor
temperature) [Phenomenon] After the machine has been turned off for
a long period of time, when making a copy immediately after the
main switch is turned ON or just after the main switch is turned
ON, service call C6050 might occur
[Cause] In which case the outside air is regarded as normal
temperature (18C or more), after approx. 20sec., the status of
machine is "Ready to copy". However, if the following factors are
present, fixing temperature might not rise enough and service call
C6050 might be detected. Due to the variation in the
temperature/humidity sensor, despite low temperature, the sensor
detects normal temperature. Power supply voltage is low. Heater
wattage is low. [Measures] Change in the detection temperature of
service call C6050 for the ends of thermistor during copy from
"100C or less" to "80C or less". The change is made so that, when
detecting normal temperature (18C or more), if the temperature on
both ends of thermistor is below 110C from power source "ON" to
approx. 20sec. after, the status of machine does not reach "Ready
to copy" until the machine does not reach the secondary
stabilization temperature. (Secondary stabilization temperature:
KM-3035: 130C, KM-4035/KM-5035: 145C)
MAIN
(Continued on the following page)
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
(Continued) No. Item Remarks Firmware
2 Correcting the problem of no paper feeding jam when DF-75 is
out of order
When the DF-75 is out of order, there is a possibility that a
cassette might not accept the command and no paper feeding JAM
might occur. Therefore the problem is corrected.
MAIN
3 Correcting the problem that SNMP information of remaining
toner is wrong and the proper information is not correctly
transmitted
There is an error in the information transmitted to the
controller of remaining toner and the information is not correctly
transmitted to the SNMP tool software developed by user. Therefore
the problem is corrected.
MAIN
4 Correcting the problem that the status of machine does not
switch to sleep mode and low power mode This problem occurs only
when using former firmware version below. (TYPE) (VER) MAIN
2FGS1015F 143 MMI 2FG2932MY 170 MMI (BA) 2FGS2015F 171
Correct the following problem. [Contents] If the following
operation is performed while polygon motor is in half speed status,
the polygon motor drives at full speed. At the same time, main
motor also continues to drive for 5sec. (1) Panel operation (2)
Open and close the original holder (platen cover). (3) Place the
original on the DP. In the condition, if the main motor stops, the
flag during main motor drive is not cleared. For that reason, auto
low power mode and auto sleep mode do not operate. (If a normal
copy or a printer output is performed, when main motor stops, the
flag during main motor drive is cleared. In such case, the problem
does not occur.)
MAIN
5 Correcting the problem after selecting the original size in
scanner mode
In scanner mode, after selecting the original size, if the size
is input or the other defined size is selected and the return key
is pressed, Continuous transmission/Sending to button is changed.
Therefore the problem is corrected.
MMI
6 Correcting the problem after selecting the transmission size
in scanner mode
In scanner mode, after selecting the transmission size and
inputting the size at the original size selection, if the return
key is pressed, "" is displayed on the upper part of transmission
size selection button. Therefore the problem is corrected.
MMI
7 Correcting the problem that an error sound is not emitted at
the scanner user information correction in scanner mode
In scanner mode, at the scanner user information correction,
when changing the setting value of save folder No., even if the
setting button is pressed, an error sound is not emitted. Therefore
the problem is corrected.
MMI
8 Correcting the problem at E-mail transmission and PC
transmission
At E-mail transmission and PC transmission, if the Stop/Clear
key is pressed while the message of Connecting is displayed after
selecting the individual address book, the processing is stopped.
However, a warning sound is not emitted. Therefore the problem is
corrected.
MMI
9 Correcting the problem of maintenance mode U960
On the operating monitor list that is output by the maintenance
mode U960, both the lowest temperature and the lowest humidity
remain the default value "0" without any change. Therefore the
problem is corrected.
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
(Continued) 10 Correcting the problem when using
FireFox browser When accessing the Web of the network scanner
using FireFox browser, there is a possibility that the main unit
might be rebooted. Therefore the problem is corrected.
MMI
11 Correcting the problem in which case the work for PC
transmission, E-mail transmission and FTP transmission is
cancelled
On the basic screen of PC transmission, E-mail transmission and
FTP transmission, in the process of address selection, work
cancellation and PC transmission/E-mail transmission/FTP
transmission basic screen, even if the address is not selected, the
start key LED lights. Then it is possible to start the
transmission. Therefore the problem is corrected.
MMI
12 Correcting the problem of message in each common address book
in scanner mode
The message "Registering/deleting address" that is displayed at
the lower left of each scanner common address book differs
depending on each language. Therefore the message is properly
changed.
LAN A/E
13 [NSI support] The change is made so that character string is
displayed for the title on the IME screen for inputting character
string-search.
MMI
14 [NSI support] At the transmission of KYOcapture, after
scanning the image in the condition that continuous scanning
setting is turned on, screen title display at function setting is
not correct. Therefore the problem is corrected. At the
transmission of E-mail, PC, DB assistant and KYOcapture, in the
condition that continuous scanning setting is turned on (other
settings are option), if setting the function - border erase -
individual border erase on the 2nd step or after of scan screen,
the title display on the screen is changed from "Scanning next
original" to "Ready to scan".
MMI
15 [NSI support] When the start key is pressed on the screen for
selecting scanner transmission size, the transmission size is not
fixed. Therefore the problem is corrected.
MMI
16 [NSI support] When setting the type of Form Fields of
KYOcapture Process Designer as Interger Float, if the number is
input by numeric keys, the default value is not cleared. Therefore
the problem is corrected.
MMI
17 [NSI support] When Authentication is in an ON" condition, if
End button is pressed on authentication screen of operation panel,
the button is pressed repeatedly. Therefore the problem is
corrected.
MMI
18 [NSI support] At the system setting of scanner default
setting, after pressing the default value setting button of
KYOcapture and Corporate address book, if a space that has no
button is pressed on the screen, a sound might be emitted.
Therefore the problem is corrected.
MMI
19 [NSI support] After registering to address list and searching
character string, if the data is registered to the list again and
the search is performed by the same character string, the result is
wrong. Therefore the problem is corrected.
MMI
20 [NSI support] In which case one address is only displayed in
individual address book, space areas can be selected. Therefore the
problem is corrected.
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
(Continued) 21 [NSI support] When EnterpriseMode is "ON"
condition, if E-mail transmission
is performed, the name of destination indicated on transmission
record is not the destination but E-mail address. Therefore the
problem is corrected.
MMI
22 [NSI support] Change the default value of the port number for
extended address book when EnterpriseMode is in an "ON" condition.
(Change to the port number that supports LDAP converter.)
MMI
23 [NSI support] When EnterpriseMode is in an "ON" condition,
the following phenomenon occurs. Therefore the phenomenon is
corrected. At E-mail transmission, if once an address is selected,
it is not possible to cancel the address. At PC transmission, if
once an address is selected in individual address book, it is not
possible to cancel the address. At PC transmission, it is possible
to select or add the same address in individual address book any
number of times.
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
PREVIOUS CHANGES Firmware is upgraded as follows. Detailss of
changes
Item Remarks FIRM
1 Measures against unsuccessful transfer on reverse side of
paper in duplex copy mode
If the transfer roller becomes dirty by the repeated copy
operation (around the time of reaching 100K copy), in duplex mode,
the reverse side of image might not be successfully transferred.
Therefore change the transfer current value for the reverse side of
plain paper. (Increase the transfer current.) (Plain paper: A3, A4,
B4, B5, 11x8.5, 11x17, Reverse side in duplex copy mode, Absolute
temperature: Humidity 100 or less) KM-3035: (Current condition) 50A
(Change) 90A KM-4035/5035: (Current condition) 60A (Change)
100A
MAIN
2 Changing the fixing control (For details, please refer to
pages following this chart.)
To improve the fixing performance, change the fixing control.
[Main changes] Changing the temperature for turning off the
noncontact temperature sensor Improving the performance for keeping
the fixing temperature
(Changing the pattern for turning on the heater) Improving the
fixing performance immediately after the stabilization Improving
the fixing performance immediately after canceling the long hours
of standby status Improving the fixing performance when setting
Bond or Rough paper Changing the basic fixing temperature
(Increasing the control temperature on Japan specification
machine.)
MAIN
MMI
MMI
BA
Firmware Information Type Program No. Check SUM Version
Remarks
MAIN 2FGS1015F 8CEF 143 New upgrade MMI 2FG2932MY 96D1 170 New
upgrade LANGUAGE A 2FG29337J F31C 24 For KMA spec. New upgrade
LANGUAGE BRA 2FGS2022C 5FEA 7 For KMA Portuguese spec. New
upgrade
When upgrading firmware or replacing board etc., please upgrade
each firmware (MAIN, MMI and LANGUAGE) to the latest version at the
same time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Item Remarks FIRM
3 Improving fixing immediately after outputting from Printing
System
When outputting data from Printing System using a special type
of media before paper feeding and after paper ejecting, if the
request for printing plain paper is made during the aging process
(*) the aging function does not work and there is a possibility
that a fixing problem might occur on the first a few sheets.
(*) During the aging process, the temperature control for
standby status is performed.
The aging function works for the following media type: Envelope,
Bond, Rough paper, Thick paper [Measures] The change is made so
that paper is not fed during aging process.
MAIN
4 Correcting the problem that the machine does not start after
downloading MMI firmware to machine
After the MMI program is loaded, the machine does not operate at
all.
MMI MMI BA
5 Scan to FTP function support
In response to the requests from KMA market, add Scan to FTP
function. (Add the function as a hidden function for function
limited version.)
MMI LAN
A/E/BR
6 Supporting NSI for full function version
The special function for KMA market is supported. (KMA
specification only) MMI MMI BA
LAN A/E/BR
7 Correcting the problem that the unusual image occurs if form
overlay is performed in copy mode after FAX transmission
Immediately after FAX transmission, if form overlay is
performed, the image on the second page is properly processed
without problems. However, the image on the first page is reduced
to the one ninth of the original size. Therefore the problem is
corrected.
MMI
MIMI
BA
8 Correcting the problem during open-faced original setting, if
the original size 11"x17" is selected for network scanner
transmission, the transmission size is processed as B5
During an open-faced original setting, the transmission size is
not reduced to the half size of the original at network scanner
transmission. (Example) On KME specification machine, if the
11"x17" size of open-faced original is selected for network scanner
transmission, auto transmission size is processed as B5. On KMA
specification machine, if the A3R size of open-faced original is
selected for network scanner transmission, auto transmission size
is processed as 8.5"x11" size. [Cause] So far, the reduction
function above was not supported in the condition that inch size
paper and metric size paper were mixed. Therefore the change is
made so that the transmission size is corrected by recognizing the
inch size or metric size regardless of the specification.
MMI
MIMI
BA
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Item Remarks FIRM
9 Correcting the problem that occurs when copy is made during
the data erasing in HDD by overwriting it (When using security
kit)
During erasing in HDD by overwriting it, if copy is made, there
is a possibility that memory overflow, C630 or C640 might be
detected. Therefore the problem is corrected.
MMI
MIMI
BA
10 Correcting the occurrence of unusual image at network scanner
transmission (E-mail transmission)
There is a possibility that data transmission might not be
correctly performed and the unual image might arise. Therefore the
problem is corrected.
MMI MIMI BA
11 Correcting the incorrect number order of the procedures for
JAM removal guidance
Correct the number order of JAM removal guidance message from
"1, 3, 3, 2, 5" to "1, 2, 3, 4, 5". [Affected languages] KMA:
French, Spanish
LAN A/E
12 Changing the control when CPU communication error occurs
Even if MMI error occurs, the communication between MMI and MAIN
is performed. When turning on the main switch or after canceling
the energy save mode, in which case MMI error occurs, there is a
possibility that fixing temperature might rise and thermostat might
break without performing the fixing control correctly. [Measures]
The change is made so that the error is corrected when detecting
the communication error in MAIN.
MAIN
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Changing the fixing control (The fixing control is changed in
which case new thermistor PT9 is used on fixing unit.) Changing the
temperature for turning off the noncontact temperature sensor
(Preventing the both ends of roller from reaching high temperature
when using small size paper) Thick paper (Bond, Rough paper, Thick
paper)
Cassette feeding (Excluding the following sizes)
185C OFF
Newly added control Cassette feeding (A5R width or smaller
(Including 5.5"x8.5"))
175C OFF
Plain paper (Excluding Bond, Rough paper, Thick paper and
Envelop)
Bypass feeding (Excluding the following sizes)
180C OFF
Newly added control Bypass feeding (A5R width or smaller
(Including 5.5"x8.5"))
170C OFF
Improving the performance for keeping the fixing temperature
(Changing the patter for turning on the heater) Improving the
fixing performance immediately after stabilization Add the
following temperature as the condition of the temperature for
turning off the noncontact thermistor. Noncontact thermistor OFF
temperature during the drive for stabilization in which case power
source is turned on:
200C (Originally, noncontact thermistor was turned off at 170C.
The status of machine is processed as standby mode.)
Improving the fixing performance immediately after canceling the
long hours of standby status The change is made so that the main
motor is left turned on for 5sec. at which time LSU speed is
changed from half speed to full speed. By the change, drive the
fixing section and increase the temperature of press roller
quickly. By doing so, improve the initial fixing performance after
leaving the machine for a long time.
Before change
X
Sub heater
Main heate
Y 11"x17"/11"x8.5" B4/B5 A3/A4
0.3 sec.
0.3 sec.
After change
OFF
OFF
OFF
ONON X
OFF
ONON X Y
Sub heater
Main heater
X Y 11"x17"/11"x8.5" B4/B5
0.3 sec.
3.0 sec.
A3/A4 0.3 sec. 0.3 sec.
Y
r
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Improving the fixing performance The parts with (*) are changed.
This change applies to KM-5035 only.
KM-5035
1 Media: Bond, Rough setting, Cassette feeding, 11"x17" No
change
2 Media: Bond, Rough setting, Cassette feeding, 11"x8.5" No
change
3 Media: Bond, Rough setting, Cassette feeding, 8.5"x11" 10C UP
(*)
4 Media: Bond, Rough setting, Cassette feeding, 8.5"x14" 10C UP
(*)
5 Media: Bond, Rough setting, Cassette feeding, A3 10C UP
(*)
6 Media: Bond, Rough setting, Cassette feeding, A4 (landscape)
10C UP (*)
7 Media: Bond, Rough setting, Cassette feeding, A4 (portrait)
10C UP (*)
8 Media: Bond, Rough setting, Cassette feeding, Folio 10C UP (*)
Changing the basic fixing temperature (Increasing the control
temperature on Japan specification machine.) This change is made to
KM-5035 only. / The temperature change is made to Japan
specification machine only. Changing the default value of fixing
correction temperature in the maintenance mode U161
Original default value
After change
U161 CORRECT TEMP
COPY UP TEMP (L) Correcting the fixing temperature at large size
copy (A3, A4, B4, B5)
50cpm machine: 55
50cpm machine: 65
(+10) (Setting the fixing correct temperature)
COPY UP TEMP (M) Correcting the fixing temperature at middle
size copy (A4R, B5R)
50cpm machine: 65
50cpm machine: 70
(+5) (Note)
The default value above is changed on KM-5035. However, the
actual fixing temperature is changed on Japan specification machine
only. Regarding the other specification machine, although the
default value is changed, the control temperature is the same as
before. Please take note of it.
When downloading the software of latest and above version, the
default value is automatically renewed to the value above one time
only. However, the default value is not be renewed from second
time.
If the setting value is changed in the field, please be sure to
change the setting value after upgrading the software.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Firmware is upgraded as follows. Details of
changes
Item Remarks FIRM
1 Preventing panel lock on logo screen
If main switch is turned on in condition that a HDD is not
installed or a HDD is disconnected from the machine, the logo
screen might lock.
MMI LX
2 Changing jam guidance message (Please refer to Fig. and on the
next page.)
Clearing paper jam on duplex unit It is difficult to find the
jammed paper inside of duplex unit just by opening the left cover.
For that reason, a paper jam might not be able to be removed.
Therefore the following message is added in addition to the present
message.
[Lift up the gray knob and remove paper from back side of the
duplex unit.]
Clearing paper jam on mail box (M-2107) Even if the process for
removing jammed paper is performed according to the message, the
jam status is not cleared. Therefore the following message is added
in addition to the present message.
[Open and close Mailbox cover again.]
MMI LX
LAN 6H
3 Correcting a panel lock problem after performing the
maintenance mode U092 (Adjusting the scanner automatically)
After finishing the maintenance mode U092 (Adjusting the scanner
automatically), if the scanner auto adjustment is performed again
in concurrence with the start LED green lighting, panel lock might
occur depending on the timing.
MMI LX
Type Program No. File Name (After uncompressing) Check SUM
Version
MAIN 2FGS1012C P2FGS101.2C1 8921 139
MMI 2FG2932LX P2FG2932.LX0 BA9C 159 New upgrade LANGUAGE A
2FG29336H P2FG2933.6H2 B75B 23 For KMA spec. New upgrade
(Note) Please note that the No.2 change is not supported when
using Europe option language. When upgrading firmware or replacing
board etc., please upgrade ALL firmware (MAIN, MMI and LANGUAGE) to
the newest versions at the same time.
-
Kyocera Mita Corporation
KM/CS-3035/4035/5035 Firmware Release Notes
A
Paper misfeed. Careful for Drum.
1. Open left cover 1. 2. Remove paper. 3. Lift up the gray knob
and remove
paper from back side of the duplex unit.
4. Close the cover.
Add the instruction "3".
Paper misfeed.
1. Open Mailbox cover. 2. Remove paper. 3. Close Mailbox cover.
4. Open and close Mailbox cover again. Add the instruction "4".
B
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Firmware is upgraded as follows.
Details of Changes Item Details F/W
1 Enhancement of dot/thin line/gray tone reproduction
If dot reproduction is poor, a gray tone image may print light.
The following modifications are carried out to correct the
problem.
* Control table for developing shift bias, duty and frequency is
changed according to drum rank. * Drum rank is categorized into
230V/240V/250V and each value is reviewed for enhancement according
to temperature/humidity table.
MAIN
Firmware Information
Type Program No. File Name (After decompression)
Check Sum Version
MAIN 2FGS1012C P2FGS101.2C1 8921 139 Please use the most current
version for each firmware (MAIN/MMI/LANGUAGE) whenever updating the
firmware or replacing the board, etc.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of Changes
Item Remarks FIRM
1 Improving the image quality in normal mode or halftone mode
during FAX transmission
Due the line width on the FAX transmission image in normal or
halftone mode, there is a possibility that the legibility of
letters might deteriorate. (To make the legibility of letters
equivalent quality to that of 2530/3530/4030, the value for image
adjustment table in the following mode has been changed.) FAX text
mode (Normal), FAX halftone mode
MAIN
Firmware Information
Type Program No. File Name (After uncompressing) Check SUM
Version
MAIN 2FGS1010A P2FGS101.0A1 2955 136 New upgrade When upgrading
firmware, please upgrade 3 types of firmware (MAIN, MMI and
LANGUAGE) to the newest version at the same time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of changes
Item Remarks FIRM
1 Adding a printer error message To support this change,
MAIN/MMI/LANGUAGE and controller FIRMWARE required. Applicable
controller firmware: Ver. 146.10
Added a printer error message: [e-MPS not stored, Press GO] In
condition of no disk (no HDD or RAM disk "OFF") or disk full,
when
trying to perform Private Print/VMB JOB/JOB reservation
function, the error message is displayed. If THE "GO" button is
pressed, error report is output. Added printer error message: [No
multi copies Press GO]
In condition of no disk (no HDD or RAM disk "OFF") or disk full,
when trying to make multiple sets of copy, the error message is
displayed. If "GO" button is pressed, error report is output.
MAIN MMI LAN
2 Changing the name of HDD overwrite function for security
kit
Change to the name of HDD overwrite function for security kit.
[Machine default setting display message]
(Old) "NSA recommend" "3-time Overwrite" [Machine status report
setting designation]
(Old) "OnceOverwrite" (New) "Once Overwrite" (Old) "NSA
recommend" "3-time Overwrite"
MMI LAN
3 Correcting the problem that saddle stitch stapling cannot be
performed at the face-up ejection setting
When setting "FACE-UP" ejection by the maintenance mode U331
(Setting the paper ejection), even if saddle stitch setting is
specified, the paper is ejected without stapling. Therefore the
following change is made. [Change] The change is made so that, when
specifying saddle stitch setting, "FACE-DOWN" ejection is performed
regardless of the setting of maintenance mode U331. (By changing to
"FACE-DOWN" ejection, the paper enters the middle tray and stapling
can be performed.)
MMI
4 Changing the specification of stepping motor
By changing the ON/OFF timing for the ejection motor, it
improves the tolerance against JAM 81 (JAM between the finisher and
copier).
MAIN
Firmware Information
Type Program No. File Name (After uncompressing)Check SUM
VER
MAIN 2FG2931NZ P2FG2931.NZ1 6403 134 New upgrade MMI 2FG2932JV
P2FG2932.JV0 FCFC 149 New upgrade LANGUAGE A 2FG29335G P2FG2933.5G2
C30D 22 For KMA spec. New upgrade
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Summary of changes 1. Measure to prevent JAM05
(Secondary paper feed is not performed) when printing in duplex
mode with A4R
or Bond paper fed from bypass tray. 2. Measure for poor fixing
when switching the paper feed cassette during continuous printing
in printer mode. 3. Adding "original setting direction" to machine
default setting. 4. Correcting a problem if the password for
network scanner is input with the numeric keys, it is changed
to
"001". 5. Fax software CF download support. 6. Preventing the
occurrence of a black line on the image due to the shadow of the
film on SRDF-2
Firmware Information
Type Program No. File Name (After uncompressing) Check SUM
MAIN 2FG2931JV P2FG2931.JV1 76F1 New upgrade MMI 2FG2932ER
P2FG2932.ER0 ED71 New upgrade LANGUAGE A 2FG29334F P2FG2933.4F2
4EEB For KMA spec.
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Details of changes
Item Remarks FIRM
1 Measures for the occurrence of JAM05 (Secondary paper feed is
not performed) when printing in duplex mode with A4R or Bond paper
fed from bypass tray
---------------------------------------------------- MAIN
2 Measure for poor fixing when switching the paper feed cassette
during continuous printing in printer mode
(This change had been made to FS-9120DN and FS-9520DN. This time
it is introduced to KM-3035, KM-4035, KM-5035.
MAIN
3 Adding "original setting direction" to machine default
setting
To meet the demands of the market, for the user who uses
original direction "Left" as the default setting, the change is
made so that the original direction can be set at in the machine
default setting. (Factory default setting is "Back".)
MMI
4 Correcting a problem if the password for network scanner is
input with numeric keys, it is changed to "001"
When setting the network scanner password using the numeric
keys, the password is changed to "001" regardless of the input
numbers. This problem is corrected. (When inputting the password
with numeric keys, "001" was referred as a fixed password.)
MMI
5 Fax software CF download support
1. If a new CF is made using a San Disk Card, File Not Found is
displayed. This problem is corrected. 2. If an 8MB CF is used, File
Not Found is displayed. This problem is corrected.
MMI
6 Preventing the occurrence of a black line on the image due to
the shadow of the film on SRDF-2
When installing a DP option (SRDF-2) in field, the shadow of the
film on SRDF-2 might be printed and a black line might arise on the
image. To prevent the problem, the default value of U068 (Adjusting
the scanning position for originals from the DP) is changed.
[Specification change]
Change the default value of maintenance mode U068 (Adjusting the
scanning position for originals from the DP).
Present conditions: [ADJUST DATA 0] After change: [ADJUST DATA
+5]
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Firmware is upgraded as follows. Summary of
changes
Data Security Kit (A) support. Supporting the setting of "Fax
Reception Bulk Print". Changing toner coverage report
specification. Adding the restriction of copy operation when
removing mechanical counter after installing the
mechanical counter once. Correcting the problem that the setting
value for printing position correction cannot be properly notified
to
printer. Changing the control of fan during preheat mode. Adding
the maintenance mode U0971 (Setting for aging before copying).
Changing LSU startup timing in silent mode. Adding the setting of
[2 sided Front page] to [Border Erase Page Setting]. Hiding "Reset"
key after downloading printer firmware. Displaying the button for
setting printer option ROM. Correcting the problem of binding
direction when scanning the original with individual border
erase
setting. Correcting the problem when setting the several sizes
of original mixed condition and the multiple original
scanning.
FIRMWARE INFORMATION
Type Program No. File Name (After uncompressing) Check SUM
MAIN 2FG2931GT P2FG2931.GT1 5A08 New upgrade MMI 2FG2932DQ
P2FG2932.DQ0 342F New upgrade LANGUAGE A 2FG29334F P2FG2933.4F2
4EEB For KMA spec. New upgrade
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Details of changes Item Remarks 1 Data Security Kit (A)
support
(Regarding Data Security Kit (A), Service Bulletin will be
otherwise issued.)
Supporting Data Security Kit (A), the data in HDD is deleted by
overwriting. It is necessary to upgrade copier software and printer
firmware to the appropriate version or later version at the same
time.
MAIN MMI
LAN A LAN E
2 Supporting the setting of "Fax Reception Bulk Print"
The change is made so that the setting of "Fax Reception Bulk
Print" supported on KM-1650/2050 is available on FAX System (J).
The item of [FAX Reception Bulk Print] is added to [Default setting
screen]-[FAX default setting]. Default value: OFF
It is necessary to upgrade copier software to the latest version
or above at the same time.
MMI LAN (ALL)
3 Changing toner coverage report specification
Toner coverage report specification is changed. (Main changes)
Display "Year/Month/Date" that was reset last time. Display toner
coverage value on the last page (the one sheet that is the
immediately preceding report output). Change the description from
"TOTAL COUNT" to "USAGE PAGES".
MAIN MMI
4 Adding the restriction of copy operation when removing
mechanical counter (option for KMA specification machine) after
installing the mechanical counter once
The change is made so that, after installing the total counter
(option for KMA specification), if the total counter is removed,
copy operation is restricted. Under the condition, copy, printer
output, FAX data printing and network scanner original scanning are
restricted. However, the maintenance mode for field service is
available.
MAIN MMI
5 Correcting the problem that the setting value for printing
position correction cannot be properly notified to printer
The following problems are corrected. In the maintenance mode
U034 (Adjusting the print start timing), even if the adjustment
value for optical axis is changed to the minus value, it is not
possible to notify the correct value to printer and to adjust to
the proper printing position. (If the power source is turned off
and on, it is possible to notify the correct value.) In the
maintenance mode U034 (Adjusting the print start timing), when the
adjustment value for center line is minus value, even if the
setting value is changed by the maintenance mode U265 (Setting OEM
purchaser code), it is not possible to notify the changed value to
printer until the power source is turned off and on.
MAIN MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Details of changes
6 Changing the control of fan during preheat mode
The following change is made to reduce the noise of fan during
preheat mode. So far, the fan on the upper part of LSU was
controlled to half speed rotation during preheat mode. This time
the change is made so that the fan is stopped during preheat mode.
(However, after printing, the fan is rotated for 3 min. even if the
machine entered preheat mode. Regarding sleep mode, the fan is
stopped.)
MAIN
7 Adding the maintenance mode U0971 (Setting for aging before
copying)
To improve the fixing performance and prevent the occurrence of
a crease on paper, when using large size paper, the aging process
is performed before starting copy. By the aging process, a few
seconds are required for the first copy. The first copy of large
size paper takes priority on the user side, the maintenance mode
U971 (Setting for aging before copying) is added so that the aging
"OFF/ON" setting is available. Large size paper:
A3/LDR/B4/LGL/A4R/FOL/LTR The maintenance mode U971 (Setting for
aging before copying) is
available for copier and FAX only. Default value: "ON (Aging
process is performed.)
MAIN
8 Changing LSU startup timing in silent mode
In silent mode, ( polygon motor low speed rotation), when large
size paper is fed after the aging process, the polygon motor is
changed to high speed rotation. [Change] The change is made so that
polygon motor goes to high speed rotation condition even during
pre-copy aging process.
MAIN
9 Adding the setting of [2 sided Front page] to [Border Erase
Page Setting]
The setting of [2 sided Front page] is added to [Border Erase
Page Setting] in copy default setting. Regarding the setting of [2
sided Front page], border erase process is performed to only the
front face of duplex copy. The process is not performed to the
reverse face.
In [Border Erase Page Setting], it is possible to select 3 items
of [Full page], [1 page only] and [2 sided Front page].
MMI LAN A
10 Hiding "Reset" key after downloading printer firmware
After ending the download of the printer firmware, if the reset
key on panel is pressed without pulling out CF, or the power source
is turned off before ending the re-download, the machine does not
recover. Therefore the problem is corrected so that the reset key
is not displayed on the download end screen.
MMI
11 Displaying the button for setting printer option ROM
When installing option ROM, option ROM button is not displayed
on printer menu. Therefore the problem is corrected. It is
necessary to upgrade printer firmware to the following version or
above. Printer firmware: Version 146.07
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Details of changes 12 Correcting the problem of
binding direction when scanning the original with individual
border erase setting
When scanning the duplex original through the DP, if the upper
corner binding by the rear side alignment and right-and-left
binding by the left side alignment, the position for individual
border erase is changed on the upper/bottom part and right/left
part. Therefore the problem is corrected.
MMI
13 Correcting the problem when setting several sizes of
originals in a mixed condition and using multiple original
scanning
[Phenomenon] After setting several sizes of originals, mixed
condition and finished size mixed condition, set multiple original
scanning, the following may occur. By using the multiple original
scanning setting, if the original width size scanned in main
scanning direction at the first step is different from the width
size scanned in main scanning direction at the 2nd step or later,
unusual image might occur at the 2nd step output. (This problem
occurs at normal copy and job reservation copy only. It does not
occur on network scanner.) [Change] The change is made so that only
when using the multiple original scanning with several sizes of
originals, mixed condition and finished size mixed condition, the
scanning process for a bundle of originals is performed by using
the width of leading image at each step. The change is made so that
the main scanning width size for the original is renewed in the
lead of each step. Also, then the original width differs from the
paper width. Therefore, in the above case only, the process for
correcting the paper width is added to scanner so that the paper
width becomes the same as the original width.
MMI
DATA SECURITY KIT COMPATIBILITY REQUIRES THE FOLLOWING FAX
SYSTEM AND PRINT SYSTEM FIRMWARE UPDATES FAX SYSTEM J: Ver.
2.17
Type Program No. File Name (After uncompressing) Check SUM
SOFTWARE, CONTROL 3DB68163D P3DB6816.3D4 5133 CF data for copier
SLOT
ROM FAX (F2) 1 3DB68113D 3DB6811.3D 5D66 Special tool ROM
ROM FAX (F2) 2 3DB68123D 3DB6812.3D D04D Special tool ROM
ROM FAX (F2) 3 3DB68133D 3DB6813.3D 2133 Special tool ROM
ROM FAX (F2) 4 3DB68143D 3DB6814.3D 0000 Special tool ROM
Remote software R2FGV217 R2FGV217.HEX --------- FAX data for
using PC remote Printing System (U), Print/Scan System (U)
Type Version File Name (After uncompressing) Check SUM
PRINTER FIRMWARE 146.07 3h8_14607.cmp D813
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of changes Item Remarks
1 Correcting a problem when C6050 occurs when returning to the
operating status from sleep mode (C6050: Abnormally low fixing unit
thermistor temperature)
[Phenomenon] C6050 Error Code may trigger. [Cause] When two or
more options are installed to the copier (Fax System/Printing
System/Scan System), the duration of the warm-up time is not long
enough when the machine is recovering from sleep mode. If printing
is performed immediately after recovering from sleep mode, the
fixing unit may not reach its specified operating temperature. The
result will be a detection of low fixing temperature, triggering a
C6050 error code. [Measures] The return time to the operating
status from sleep mode is lengthened by 10sec.
2 Preventing an increase of fixing temperature (C6020:
Abnormally high fixing unit thermistor temperature)
[Phenomenon] C6020 might occur or the thermostat might open.
[Cause]
1. When setting bypass feeding tray for thick paper, if a re-try
is repeated at paper feeding, the temperature on the both ends of
fixing section increases above the controlled temperature.
2. If main switch is repeatedly turned off/on, the temperature
at the middle of fixing section increases over the controlled
temperature.
[Measures] 1. The specification is changed so that the fixing
temperature is decreased when
the interval of paper feeding/job process exceeds 5sec. or more.
2. The temperature control for the main heater thermistor is added
to the
condition for fixing control right after turning on the power
source (approx. 4sec.).
3 Correcting a problem for
printer output after the cover mode process in copy mode
In copy mode, when the last copy is a blank sheet in cover mode
and transparency + lining paper (blank paper) mode, if printer
output is performed, the machine may lock up. This problem is
corrected. (The machine returns to ready status by pressing cancel
key.)
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Firmware Information
Type Program No. File Name (After uncompressing)
Check SUM
MAIN 2FG2931DQ P2FG2931.DQ1 CA67 New upgrade MMI 2FG2932BN
P2FG2932.BN0 1E54
LANGUAGE A 2FG29333E P2FG2933.3E2 7653 For KMA spec. When
upgrading firmware, please upgrade 3 types of firmware (MAIN, MMI
and LANGUAGE) to the newest version at the same time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of changes
Item Remarks Ver 1 Supporting key card/key counter for
printer Printer firmware also needs to be upgraded to the
following version or later. Printer firmware: Ver. 145.05 or
later
In response to requests from KMAU, the change is made so that
printer printing can be controlled by key card/key counter. (In
field, the commercial item is connected to the I/F for key
counter.) The selection item of [Key card (Printer)] is added to
U204 (Setting the presence or absence of a key card or counter). By
selecting the [Key card (Printer)], copy mode is also controlled by
key card/key counter.
MAINMMI
2 Correcting the problem that the ID number for administrator is
not effective for fax
In fax mode, the machine recognizes the ID number [0000] only.
This problem is corrected.
MMI
3 Correcting the problem that fax printing is counted to the
department for key card when installing key card system MK-II
When installing key card system MK-II, if fax output is
performed in condition that the department card is inserted, the
job should be originally counted at the department [000]. However,
the job is counted at the department of key card. This problem is
corrected. [Change] The change is made so that fax output is
counted at the department [000] by the count process of key
card.
MMI
Type Program No. File Name (After uncompressing) Check SUM
MAIN 2FG2931CP P2FG2931.CP1 196C New upgrade MMI 2FG2932BN
P2FG2932.BN0 1E54 New upgrade LANGUAGE A 2FG29333E P2FG2933.3E2
7653 For KMA spec.
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same time.
Affected Machine Serial Nos.: KM-3035 : From K3023393 on KM-4035 :
From L3014436 on KM-5035 : From M3007845 on
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of changes
Item Remarks Ver. 1 Adjusting the original scanning position
on DP
If old software is rewritten by new software, the setting value
for the maintenance mode U067 and U072 is automatically changed to
the value according to adjustment for new software.
However, if the machine is rewritten by new software and is
rewritten by old software again, the setting value does not return.
The setting value is changed inside of the machine, and
initializing by U020 is required when new software is returned to
old software.
When option DP is installed to the machine, the original
scanning position might be displaced. Therefore the default value
is changed in the following simulation. [Contents of changes] 1.
Change the default setting value. 2. There is the possibility that
adjustment range might be exceeded depending on the machine.
Therefore shift the center scanning position for the adjustment
range.
U067 (Adjusting the center line for scanning an original on the
contact glass) (1) (2) Default value ADJUST DATA 1 +18 4 U071
(Adjusting the DP scanning timing) (1) Default value LEAD EDGE ADJ
12 0 Default value TRAIL EDGE ADJ 32 0 U072 (Adjusting the DP
center line) (1) (2) Default value DATA (1 sided) 20 (3 Default
value DATA (2 sided front) (15 ( +2 Default value DATA (2 sided
back) (20 ( (3
MMI
2 Correcting the problem that, even if duplex priority is set by
the maintenance mode U343
without HDD, duplex copy does not take
preference
So far, when HDD was not installed, the setting of the
maintenance mode U343 was not referred. This time the change is
made so that the setting of U343 becomes effective regardless of
the presence or absence of HDD.
MMI
3 Correcting the problem that, when executing the program
registration for individual border erase, the setting value for
border erase width is not backed up
If the program registration is executed after setting individual
border erase and the registered problem is called up after turning
off/on the power source once, the setting of the border erase width
for the individual border erase is not effective. This problem is
corrected.
MMI
Firmware Information
Type Program No. File Name (After uncompressing)
Check SUM
MAIN 2FG2931BN P2FG2931.BN1 DDDC MMI 2FG2932AM P2FG2932.AM0 1DC2
New upgrade LANGUAGE A 2FG29333E P2FG2933.3E2 7653 For KMA
spec.
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Summary of changes 1. Adding the function for
individual border erase. 2. Adding the function of immediate job
stop when the upper limit for department management exceeded. 3.
Correcting the problem that JAM05 might occur if key counter is
pulled out in the middle of copy. 4. Supporting Chinese paper. 5.
Supporting the cassette for 8K and 16K size paper (Chinese paper).
6. Improving finisher eject productivity when several sizes of
paper are used for a job. 7. Correcting the problem of display for
paper eject to the center folding tray in printer mode. 8.
Correcting the problem that the original setting direction is not
correctly displayed when selecting booklet
setting. 9. Changing French message and Italian message for
Europe. 10. Changing the description of paper size (8K, 16K) for
Taiwan specification machine. 11. Changing the message of Ready to
preview copy for traditional Chinese language.
Firmware Information
Type Program No. File Name (After uncompressing) Check SUM
MAIN 2FG2931BN P2FG2931.BN1 DDDC New upgrade MMI 2FG29329L
P2FG2932.9L0 AE3F New upgrade LANGUAGE A 2FG29333E P2FG2933.3E2
7653 For KMA spec. New upgrade
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Details of changes Item Remarks Ver. 1 Adding the function
for
individual border erase [Change] 1. Add the function for
[Individual Border Erase] to Erase Mode. The change is made so that
erase width can be individually changed for 4 sides of paper. 2.
Add [Border Erase Page Setting] to Copy default. (Default: Not
displayed) The change is made so that the setting of First Page
Only or All Pages can be selected for [Individual Border Erase].
(Default: All page) If the First Page Only is selected, the
[Individual Border Erase] setting is effective for the first page
only. Regarding the rest pages, the setting is not effective. 3.
Add the maintenance mode U280 (Setting Erase Mode Option).
(Default: OFF) The change is made so that it is possible to select
whether the [Border Erase Page Setting] is displayed or not. PAGE
SETTING ON selection: Border Erase Page Setting can be selected by
copy default setting. PAGE SETTING OFF selection: Border Erase Page
Setting cannot be selected by copy default setting. In that case,
the [Border Erase Page Setting] is set for all pages.
MMI
LAN A
2 Adding the function of immediate job stop when the upper limit
for department management exceeded
Add the immediate job stop function when the upper limit for
department management exceeded. (Only in copy mode and printer
mode) [Stop job immediately] mode is added to [Excess of limit
setting] for management default setting so that the following 3
modes can be selected. [Before change] [Unable to use] or [Only
warning] mode can be selected. [After change] [Stop job
immediately], [Stop after job done] or [Only warning] mode can be
selected.
MAIN
LAN A
3 Correcting the problem that JAM05 might occur if key counter
is pulled out in the middle of copy
If key counter or key card is pulled out in the middle of copy,
JAM 05 might occur. Therefore, the change is made so that a blank
sheet is output when the key counter or key card is pulled out in
the middle of copy.
MAIN
These displays are added.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
4 Supporting Chinese paper
Adding [Normal paper mode setting] to the maintenance mode U114
(Setting SC mode)
To support Chinese paper, [Normal paper mode setting] is added
to the maintenance mode U114 (Setting SC mode). Add [Normal paper
mode setting] to U114. When setting the maintenance mode U114 as
[Normal paper mode setting], the separation control for normal
paper is performed in the same way as thin paper. (Attention)
Regarding Chinese specification machine, default setting is MODE 1
(ON setting). Please note that Chinese specification machine is
also set as MODE 0 (OFF setting) when executing the maintenance
mode U020 (Initializing all data). (Regarding U002 (Setting the
factory default data) and U021 (Initializing counters and mode
settings), the former settings are inherited.) This change for
supporting Chinese paper is available only when the maintenance
mode U252 (Selecting destination) is set as ASIA.
MAIN
MMI
5 Supporting the cassette for 8K and 16K size paper (Chinese
paper)
The change is made so that 8K (8 lengthwise) or 16K (16
lengthwise) size can be selected by paper size setting for cassette
in machine default setting mode.
MMI
6 Improving finisher eject productivity when several sizes of
paper are used for a job
Copy productivity is improved when the several sizes of paper
used for a job are ejected to finisher without stapling. [Present
conditions] When several sizes of paper are ejected to finisher,
each paper is ejected to main tray. The operation is the same
condition as that of single copy. [Change] The change is made so
that, if Auto Selection setting is selected, the same size papers
are ejected as a bundle when ejecting the paper to finisher without
stapling.
MAIN
7 Correcting the problem of display for paper eject to the
center folding tray in printer mode
When designating the center folding tray for paper eject in
printer mode, the eject place is displayed as Inner tray on the
screen during the copy. Therefore the change is made so that the
eject place is displayed as Finisher tray 2. (The actual eject
operation is correctly performed.)
MMI
8 Correcting the problem that the original setting direction is
not correctly displayed when selecting booklet setting
In booklet mode, if booklet key is selected, the following
problem might occur. Therefore the problem is corrected.
[Phenomenon] On the left side of page numbering screen, the
description for checking the original setting direction is not
correctly displayed. The original setting direction can be set
rear/left. However, the message Check direction of original top
side. is not displayed. Instead of the message, Place the original
top on the rear side. Possible to use lengthwise original only. is
displayed.
MMI
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Details of changes
Item Remarks Ver. 1 Correcting a problem with a band on the
image that does not meet the specification at the printing with
undefined size paper by T7 control
The band image setting for T7 control is differentiated from the
setting for during printing, and the setting for A3 lengthwise
preset size is adapted for even undefined size paper.
083 MAIN AM
2 Measures against the fixing problem under low temperature /
low humidity environment
Right after the stabilization of fixing section, there is the
possibility that fixing high temperature offset might occur at
automatic duplex processing with large size or small size paper
under low temperature / low humidity environment. This problem is
corrected.
086 MAIN AM
Firmware Information
Type Program No. File Name (After uncompressing) Check SUM
MAIN 2FG2931AM P2FG2931.AM1 3A69 New upgrade MMI 2FG29328K
P2FG2932.8K0 4DAF LANGUAGE A 2FG29332D P2FG2933.2D2 83EE For KMA
spec.
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Summary of Details Supporting special paper
setting (Letterhead support) for copy function (Adjusting print
direction for single-sided or duplex copy) Unifying the image
direction for letterhead, preprint and pre-punched paper (When
installing inner finisher) Changing the number of sheets for tray
capacity on DF-73 (1,000 sheets finisher) Supporting fax remote
setting through network (Address Editor for Fax support) Supporting
Kyocera logo on the opening screen of operation panel Supporting
Kyocera logo on network scanner web page Disusing the input of
administrator number when performing drum refresh
Firmware Information
Type Program No. File Name (After uncompressing)
MAIN 2FG29319L P2FG2931.9L1 AD35 New upgrade MMI 2FG29328K
P2FG2932.8K0 4DAF New upgrade LANGUAGE A 2FG29332D P2FG2933.2D2
83EE For KMA spec.
When upgrading firmware, please upgrade 3 types of firmware
(MAIN, MMI and LANGUAGE) to the newest version at the same
time.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Detail of changes
Item Remarks Ver 1 Measures against printer
communication error During printer output, if another process
such as fax transmission is performed, processing is increased
inside of engine. Then there is the possibility that communication
error might occur between engine and printer. The change is made so
that printing is normally finished even if communication error
occurs.
MAIN 8K
2 Measures against the problem when no paper feeding JAM occurs
in printer duplex mode
If no paper feeding JAM occurs while printing in duplex printer
mode, paper remains in duplex unit. This problem is corrected.
MAIN 8K
3 Supporting special paper setting (Letterhead support) for copy
function (Adjusting print direction for single-sided or duplex
copy)
When printer is not installed, the selection or setting for
special paper operation cannot be done. Only printer job supports
special paper operation setting. The selection or setting for
special paper operation can be always done. Copy job also supports
the special paper operation setting as well as printer job. If the
special paper setting is set as [Adjust print direction] and paper
type is letterhead, preprint or pre-punched paper, when printing in
single-sided copy mode, the machine operates similarly to the
duplex copy mode by adding dummy white paper. (Restrictions) When
setting the finishing options (staple, punch), if the paper size is
not suitable for duplex copy, paper direction might not accord with
image direction.
MAIN 8K
MMI 8K
4 Unifying the image direction for letterhead, preprint and
pre-punched paper (When installing inner finisher)
When using letterhead with its defined direction, image
direction is rotated by 180 degrees in copy mode, and paper
direction does not accord with the image direction. This problem is
corrected. When the selected paper feed source is bypass and paper
type is letterhead, processing is controlled so that image
direction is not changed between the original scanning with table
and the original scanning with DP. When paper type for the selected
paper feed source is letterhead, preprint or pre-punched paper, the
change is made so that image direction is not changed between the
original scanning with table and the original scanning with DP.
MAIN 8K
MMI 8K
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Detail of Changes
5 Changing the number of sheets for tray full on DF-73 (1,000
sheets finisher)
1. When making multiple copies with staple on DF-73, the upper
limit of ejected paper might exceed by the thickness of the
staples. Then paper jam might occur. Therefore the limit number of
sheets for A4R and letter size is fixed as follows.
MAIN 8K
ON/OFF switching for the limit number of sheets is synchronized
with maintenance mode U342 (Setting the ejection restriction). In
staple mode, fix the limit number for sets of paper on DF-73. When
exceeding the limit number of sheets, message is displayed. Then,
if start key is pressed, restart the operation. (Printer output is
restarted by pressing GO key.) 2. The following change is made.
Copy: As far as A4R or Letter size paper, overflow is detected
at 500 sheets with shift process.
Printer: Overflow is detected at 500 sheets when using A4R or
Letter size paper regardless of shift process.
Bind with 2 to 9 sheets of paper 28 sets of paper Large size
(A3, B4, LD, LG) Bind with 10 to 20 sheets of paper 12 sets of
paper
Bind with 2 to 9 sheets of paper 50 sets of paper
6 Measures against processing lock during printer output
When paper feed is requested on printer, if some kinds of errors
(paper empty occurs or cassette comes off) occur, processing lock
might occur.
MAIN 8K
7 Correcting the problem while lifting up cassette
After pulling out or inserting the selected cassette, while
lifting up the cassette, if printer job is sent with bypass feed
setting, the paper feed does not start. This problem is
corrected.
MAIN 8K
8 Correcting the problem that the image on the trailing edge is
missing when printing with envelope COM #9
----------------------- MAIN 8K
MMI 8K
9 Correcting the information notified to controller when paper
jam occurs on finisher
When paper jam occurs on finisher, the information such as cover
open is not normally notified to controller. This problem is
corrected.
MAIN 8K
10 Correcting the problem that copied image is cut when several
sizes of paper are mixed
When A4R and B4 size papers are mixed, if the copied image is
ejected in the order of A4R ( B4 to finisher face-up tray, B4 size
image is cut by the width for A4R. This problem is corrected.
MAIN 8K
11 Correcting the problem that copy job is stopped when reaching
tray full condition at shift ejection on DF-73 (1,000 sheets
finisher)
Copy job disappears when reaching tray full condition at shift
ejection on DF-73. This problem is corrected. (Though the tray full
occurs in the middle of the job, if the tray full is released,
Ready to copy is displayed.)
MAIN 8K
12 Correcting the problem that center folding processing cannot
be performed for a sheet of printer job with saddle stitch
When only a sheet of printer job with saddle stitch processing
is sent, the job is ejected to main tray without center folding
processing. This problem is corrected.
MAIN 9L
Bind with 10 to 20 sheets of paper 20 sets of paper Small
size
Bind with 21 to 30 sheets of paper 16 sets of paper
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Detail of Changes
13 Changing the control for T7 The following change is made to
prevent the toner from adhering to due to the stains on transfer
roller caused by T7 mode. (Before change) When electrostatic charge
is OFF condition, impress developing bias for applying toner.
(After change) When electrostatic charge and developing bias are ON
condition, apply toner by LSU writing. Changing SIM 144 (Setting
toner loading operation) Before change After change Mode 0 OFF OFF
Mode 1 OFF ON (After both single-sided and duplex copy)Mode 2 ON
(After single-sided copy) ON (After single-sided copy) (Default
setting is Mode 2 as before.)
MAIN 9L
14 Measures against unsuccessful fixing processing for A4R size
paper fed from cassette 4 (bond paper) in printer mode
The change is made so that printing cannot be performed during
post-aging for fixing control.
MAIN 9L
15 Correcting the problem that paper feed cassette for copy is
changed when entering address selection screen for network scanner
while interrupting copy
The change is made so that, when using network scanner, the
initialization related to original size for network scanner is
performed.
MMI 8K
16 Correcting the problem that, if the PDF file scanned by
network scanner is attached to E-mail, the PDF file cannot be
printed
--------------------- MMI 8K
17 Correcting the problem of display for maintenance mode U660
and U911
U660: Setting system (Communication 2)
U911: Checking/clearing copy counts by paper sizes
When language display is other language except Japanese,
unnecessary @ is displayed in the item name for U660. This problem
is corrected. When language display is other language except
Japanese and destination setting is INCH, x that shows the size for
inch size paper in U911 is not normally displayed. This problem is
corrected. (Ex.: [8.5x11] is displayed as [8.511].)
MMI 8K
18 Supporting fax remote setting through network (Supporting
Address Editor for Fax)
The change is made so that the edit or registration for fax one
touch dial etc. can be done through network with PC. The following
change is required to make the above function available. NETWORK
FAX CD VER 1.30 (Address Editor for FAX) FAX SYSTEM J VER2.08 For
CF 3DB68161B For ROM 3DB68111B/68121B/68131B/68141B For remote
R2FGV208
MMI 8K
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Detail of Changes
19 Supporting Kyocera logo on the opening screen of operation
panel
Kyocera Mita logo displayed on the opening screen of liquid
crystal operation panel is changed to Kyocera logo.
MMI 8K
20 Correcting the problem that the screen for inputting code
cannot be closed when entering job reservation mode with the
department that exceeds the limit value
[Change] When reserving job, confirmation dialogue for the
department that exceeds the limit value is not displayed, and the
screen is shifted to basic screen. On the basic screen, the
notification that shows the excess of limit value is displayed.
MMI 8K
21 Supporting the processing while displaying the guidance for
black line
Even if fax or printer job is received while displaying the
guidance for black line, the job is not output until the guidance
is released. This problem is corrected.
MMI 8K
22 Correcting the problem that the original size for copier is
changed by changing the original size for scanner
---------------- MMI 8K
23 Changing the processing when clearing the counter for all
departments in department management mode
In department management mode, the counter for all departments
is cleared on operation panel, the operation panel might show no
reaction for about 10 to 15 sec.. Therefore the change is made so
that the message Please wait is displayed on the screen while
clearing the counter.
MMI 8K
24 Correcting the problem of program registration or boot for
exposure step
After performing program registration by exposure 0.5 step, if
the exposure step is changed to by 1 step and the program is
booted, the exposure display might differ from the registered data.
This problem is corrected.
MMI 8K
25 Correcting the problem that cancel screen is displayed if
service call is released during printer output
When service call occurs during printer output, if the service
call is released by opening or closing front cover, printer screen
is changed to cancel I/F selection screen. Therefore, the change is
made so that the printer screen is shifted to the screen for
showing the printing suspension or paper jam.
MMI 8K
26 Correcting the problem caused while selecting the destination
for fax transmission
If the machine gets into low power mode by pressing energy save
key while selecting the destination for fax transmission, the
address setting is not cleared even after returning to normal mode.
This problem is corrected.
MMI 8K
27 Supporting Kyocera logo on network scanner web page
Kyocera Mita logo on scanner web page is changed to Kyocera
logo. MMI 8K
28 Correcting the problem that, if copy is made right after the
power source is turned on in department management ON condition,
the copy count cannot be notified to controller
When printer is installed, in department management ON
condition, while the printer gets count information for each
department in order, if copy is made right after the power source
is turned on with the department that has already got the count
information, the copy count cannot be notified to printer
controller. This problem is corrected.
MMI 8K
29 Correcting the problem that operation panel does not go back
to copier screen by function switching key
If the machine gets into PC transmission screen during copy
suspension status, the screen does not go back the copy screen by
function switching key. This problem is corrected.
MMI 8K
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Detail of Changes
30 Correcting the problem that, if copy job and printer job are
processed with the same department code in department management ON
condition by interruption, either counter is overwritten
In department management ON condition, when trying to process
copy job and printer job simultaneously with the same department
code, if priority output is performed for interruption copy or job
reservation, the count for the first finished function might not be
saved. This problem is corrected.
MMI 8K
31 Disusing the input of administrator number when performing
drum refresh
When user adjustment key is pressed on the initial setting
screen, the screen for inputting administrator number is displayed.
If the administrator number is not correctly input, it is not
possible to enter user adjustment screen.
(Flow for drum refresh) Initial setting Screen for inputting
administrator number Screen for user adjustment Screen for drum
refresh
When user adjustment key is pressed on the initial setting
screen, user adjustment screen is displayed.
(Flow for drum refresh) Initial setting ( Screen for user
adjustment ( Screen for drum refresh
The software is changed so that, when user adjustment key is
pressed on the screen for initial setting, the processing for
operation and display on the screen for user adjustment is
performed, not performing the processing for operation and display
on the screen for inputting administrator number.
MMI
8K
32 Correcting the problem of the department management list
display when exceeding the limit number of sheet
In condition that department management is available for copier,
not available for printer, if the number of processing in
department management mode is limited for copy and printer in a
lump, when displaying department code list at department code
setting on operation panel, [!] mark that should be displayed for
the department that exceeds the limit number of sheet is not
displayed. This problem is corrected.
MMI
8K
33 Correcting the problem when running maintenance mode U021 or
U252
When running U021 or U252, in department management mode, the
counter setting for each paper is not changed according to the
destination. This problem is corrected. (Ex.: Even if the
destination is changed from METRIC to INCH, the display remains
METRIC.)
U021: Initializing counts and mode U252: Setting the
destination
MMI
8K
34 Correcting the problem that preheat cannot be released during
network fax transmission or reception
If network fax transmission or reception is performed in preheat
condition, the preheat condition cannot be released by energy save
key during transmission or reception. This problem is
corrected.
MMI
8K
35 Correcting the problem that the drive is continuously
performed at fax printing right after the stop of drum refresh
If fax report is printed right after stopping the drum refresh,
primary paper feed is performed, but secondary paper feed is not
started. This problem is corrected. (After waiting for 5 min. that
requires for drum refresh, the data is output.)
MMI
8K
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Summary of Changes
1. Measure to correct a problem when entering the sleep mode.
(The machine may fail to enter the sleep mode.)
2. Addition of new Simulation U956 to enable you to select
old/new Conveying Unit. 3. Measure for a poor fixing problem in
rotation sort duplex copy mode. 4. Measure for a poor fixing
problem for small size paper with the 30 cpm model. 5. Change to T7
control after the duplex printing is completed.
Firmware Information
Type Program No. File Name (After decompression)
Check Sum
MAIN 2FG29317J P2FG2391.7J1 FE17 New upgrade MMI 2FG29327J
P2FG2932.7J0 660B New upgrade LANGUAGE A 2FG29332D P2FG2933.2D2
83EE Be sure all levels are updated to the current levels listed in
the above table.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Details of Changes Item Contents 1 Measure to correct a
problem when entering the sleep mode
The machine may restart when it enters the sleep mode.
2 Addition of new simulation U956 to enable you to select
old/new unit setting in compliance with the change to Conveying
Unit.
As a result of an improvement to the Conveying Unit, Sim U956 is
added to support the old/new Unit.
U956: Set the type of Conveying Unit You can select "New" or
"Old" setting.
1. When only the firmware version is upgraded, original type of
the conveying unit remains. (It is not necessary to set again.) 2.
Please be aware that after executing U020 (Initialize all data),
you need to change the setting to "Old" if the conveying unit is
old-type as it will be initialized to "New" type. 3. If that the
Conveying Unit is replaced using the new-type Unit, please change
the U956 setting to "New" with this firmware.
3 Measure for a poor fixing problem in rotation sort duplex copy
mode
In some cases, poor fixing may occur on the center of copy in
rotation sort duplex copy mode. (Modification )
Fixing temperature setting varies between R direction and
regular feed. When temperature setting is to change from high to
low, it is now gradually lowered. (Lowered by 5 degrees C per 15
seconds.)
Originally, the temperature is rapidly decreased to the setting
temperature by turning the heater OFF continuously. This method may
cause the setting temperature at the middle section of fixing
roller to become excessively low.
4 Measure for a poor fixing problem for small size paper with
the 30 cpm model
The copy temperature for small size paper is changed from +20
degrees C to +25 degrees C.
U161: Setting fixing control temperature Default setting for
"COPY UP TEMP(S)" is changed only for the 30 cpm model.
20 degrees C --> 25 degrees C 5 Change to T7 control
after duplex printing As a measure to prevent rear side of the
paper from becoming stained, the T7 control is not performed when
the duplex printing is completed. It is now performed when next
simplex copying is completed.
-
KM/CS-3035/4035/5035 Firmware Release Notes
Kyocera Mita Corporation
Previous Changes Firmware is upgraded to support Print Scan
System (U). When Installing Print Scan System (U), please check the
firmware Versions for Copier
Firmware Information Type Program No. File Name (After
uncompression)
Check SUM
MAIN 2FG29315G P2FG2931.5G1 B7E6 New upgrade MMI 2FG29326H
P2FG2932.6H0 2D78 New upgrade LANGUAGE A 2FG29332D P2FG2933.2D2
83EE For KMA spec. New upgrade
When upgrading firmware, please upgrade all 3