Programming Item List Hybrid IP-PBX Model No. KX-HTS824 KX-HTS32 Thank you for purchasing this Panasonic product. Please read this manual carefully before using this product and save this manual for future use. In particular, be sure to read "1.1 For Your Safety, page 8" before using this product. KX-HTS Series: PJMPR Software File Version 001.40000 or later Manuals and supporting information are provided on the Panasonic Web site at http://www.panasonic.net/pcc/support/pbx
92
Embed
KX-HTS32 Hybrid IP-PBX KX-HTS824 - phone-master.nl · Programming Item List Hybrid IP-PBX ... If the PBX undergoes a sudden power failure or if the ... if system data has been saved
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Programming Item ListHybrid IP-PBX
Model No. KX-HTS824KX-HTS32
Thank you for purchasing this Panasonic product.Please read this manual carefully before using this product and save this manual for future use.In particular, be sure to read "1.1 For Your Safety, page 8" before using this product. KX-HTS Series: PJMPR Software File Version 001.40000 or later Manuals and supporting information are provided on the Panasonic Web site athttp://www.panasonic.net/pcc/support/pbx
The Programming Item List is designed to serve as a system programming reference for the PanasonicHybrid IP-PBX. It explains how to program this PBX using Web Maintenance Console.The Programming Item List is divided into the following sections:Section 1, Overview
Provides an overview of programming the PBXSection 2, Programming Items
Serves as a reference for programming items when using Web Maintenance Console to program thePBX.
Trademarks• Microsoft, Outlook, Internet Explorer, Windows and Windows Vista are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.• Intel and Intel Core are trademarks of Intel Corporation in the U.S. and/or other countries.
• Mozilla and Firefox are registered trademarks of the Mozilla Foundation.
• All other trademarks identified herein are the property of their respective owners.
• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
• Google® and Google ChromeTM are trademarks or registered trademarks of Google, Inc.
Notice• During a long programming session, it is highly recommended that you periodically save the system data
to the internal storage. If the PBX undergoes a sudden power failure or if the system is reset for somereason, all the system data in the RAM will be lost. However, if system data has been saved to theinternal storage, it can be easily reloaded.
• To save the system data to the internal storage, press the "Save & Logout" button in the top right cornerof the screen before resetting the PBX or turning off the power.After the data is changed, if you close the browser without pressing the "Save & Logout" button in the topright corner of the screen, the data may not be saved. Make sure to press the "Save & Logout" buttonbefore exiting the configuration.
Introduction
2 Programming Item List
List of AbbreviationsRefer to List of Abbreviations in the Feature Manual.
List of Abbreviations
Programming Item List 3
List of Abbreviations
4 Programming Item List
Table of Contents1 Overview .................................................................................................. 71.1 For Your Safety ................................................................................................................ 81.2 Input Rules ..................................................................................................................... 101.2.1 Valid characters ............................................................................................................ 101.2.2 Input character restrictions ........................................................................................... 101.3 PC Programming ........................................................................................................... 141.3.1 Starting Web Maintenance Console ............................................................................. 141.4 Easy Setup Wizard ........................................................................................................ 15
This section provides an overview of programming thePBX.
Programming Item List 7
1.1 For Your SafetyTo prevent personal injury and/or damage to property, be sure to observe the following safety precautions.The following symbols classify and describe the level of hazard and injury caused when this unit isoperated or handled improperly.
WARNINGThis notice means that misuse could result in deathor serious injury.
CAUTIONThis notice means that misuse could result in injuryor damage to property.
The following types of symbols are used to classify and describe the type of instructions to beobserved.
This symbol is used to alert users to a specific operating procedure that must not beperformed.
This symbol is used to alert users to a specific operating procedure that must be followed inorder to operate the unit safely.
1.1 For Your Safety
8 Programming Item List
WARNING
• Unplug the PBX from the AC outlet if it emits smoke, an abnormal smell or makes unusual noise. Theseconditions can cause fire or electric shock. Confirm that the smoke has stopped and contact anauthorized Panasonic Factory Service Center.
CAUTION
• To the Administrator or Installer regarding account passwords1. Please provide all system passwords to the customer.
2. To avoid unauthorized access and possible abuse of the PBX, keep the passwords secret, andinform the customer of the importance of the passwords, and the possible dangers if they becomeknown to others.
3. The PBX has no passwords set initially. For security, select an installer password as soon as thePBX system is installed at the site.
4. Change the passwords periodically.
5. It is strongly recommended that passwords of 10 numbers or characters be used for maximumprotection against unauthorized access.
• There is a risk that fraudulent telephone calls will be made if a third party discovers a personalidentification number (PIN) (verification code PIN or extension PIN) of the PBX.The cost of such calls will be billed to the owner/renter of the PBX.To protect the PBX from this kind of fraudulent use, we strongly recommend:a. Keeping PINs secret.
b. Selecting complex, random PINs that cannot be easily guessed.
c. Changing PINs frequently.
1.1 For Your Safety
Programming Item List 9
1.2 Input RulesThis chapter describes rules regarding input in detail.
1.2.1 Valid charactersDescribes characters that can be input.An input character check is implemented through Javascript when using Web Maintenance Console, anderrors are displayed in a dialog box when invalid characters are input.
Valid characters are shown in the following:ASCII code
1.2.2 Input character restrictionsA set of character restrictions is defined as follows:
Input Type Valid characters Usage
Dial1 Numbers <0–9>Others <# *>
Dial for trunk.
Dial3 Numbers <0–9>Others <# * N (N=2–9) X (0–9) Z (Z=1–9)>
Dial for outbound.
Dial4 Numbers <0–9>Others <# * N (N=2–9) X (0–9, # * {# and * work as awild card.}) x>
Dial for dialing table.
UnsignedNumber
Numbers <0–9>Others < . >However, decimal points are omitted.
Used for input of numerical valuesusing [0–9] with a clearly definedrange. (Usage is separate from"Text Numeric")The range is not by the number ofdigits but indicated by the actualnumerical range that can be input(for port numbers, "1-65535").
Text No input restrictions.
TextNumeric
Numbers <0–9> Used for the input of digits [0–9] asa character string for floatingextension numbers, etc. (Usage isseparate from "UnsignedNumber") Indicated by a range,such as from 3 digits in length, etc.
Text LCD Valid characters and the valid number of charactersused are in compliance with the LCD displayspecifications. No input restrictions.
Character strings displayed in LCD
TextLCDHDV
Valid characters and the valid number of charactersused are in compliance with the LCD of HDV seriesdisplay specifications. For more information aboutinput characters, refer to 5.1 Input Characters(TextLCDHDV).
Character strings displayed in LCDof HDV series.
Text1 Numbers <0–9>Letters <a–z, A–Z>
Character strings consisting ofalphanumeric characters only
Text3 Numbers <0–9>Letters <a–z, A–Z>Others < - . >Input error conditionsThe following conditions are invalid for inputaccording to the RFC rules• A hyphen at the beginning of input characters will
be invalid• A hyphen at the end of input characters will be
invalid• A hyphen input before or after a dot will be invalid
RemarksValues of 1, 01 and 001, or 10 and 010 arerecognized as the same value and are saved withoutthe leading 0s.Input error conditions1. Input of class E: When the upper 4 Bits of the
first octet is 1111, it will be treated as an error.Error example: 240.0.0.0, 255.0.0.0
2. Input of class D: When the upper 4 Bits of thefirst octet is 1110, it will be treated as an error.Error example: 224.0.0.0, 239.0.0.0
3. Input of local loop back address: Input of127.0.0.1 will be treated as an error.
1.2.2 Input character restrictions
12 Programming Item List
Input Type Valid characters Usage
SubnetMask
Numbers <0–9>Others < . > *1
RemarksPrefix description such as "/24" will not be accepted.Input error conditionsFor the first to fourth octet, only the following valuesare accepted. All others will be treated as errors.255(0xFF), 254(0xFE), 252(0xFC), 248(0xF8),240(0xF0), 224(0xE0), 192(0xC0), 128(0x80),0(0x00)
SubnetMask2
Numbers <0–9>Others < . > *1
RemarksPrefix description such as "/24" will not be accepted.“0.0.0.0” cannot be set.
SubnetMask3
Numbers <0–9>Others < . > *1
RemarksPrefix description such as "/24" will not be accepted.The following values cannot be set:• 0.0.0.0
• 255.255.255.255
SubnetMask4
Numbers <0–9>Others < . >*1
RemarksPrefix description such as "/24" will not be accepted.For the first to fourth octet, only the following valuesare accepted:0 (0x00)–255 (0xFF)
MACAddress
Numbers <0–9> Letters <a–f, A–F>Others < : >RemarksOnly the following input is accepted, with each "x"being a number or letter as described above.xx:xx:xx:xx:xx:xx (17 characters in total) Input errorconditionsInput of broadcast/multicast addresses will be treatedas an error.: When Bit 0 of the first octet is 1, it will be treated asan error.Error example: 01:00:00:00:00:00
MACAddress2
Numbers <0–9> Letters <a–f, A–F> Others < : >RemarksOnly the following input is accepted, with each "x"being a number or letter as described above.xx:xx:xx:xx:xx:xx (17 characters in total)
*1 Only valid when it is required to divide into octets.
1.2.2 Input character restrictions
Programming Item List 13
1.3 PC Programming1.3.1 Starting Web Maintenance Console
System programming, diagnosis and administration can be performed with a PC using Web MaintenanceConsole. Web Maintenance Console is accessed through a Web browser running on a networked PC.This section describes how to set up and access Web Maintenance Console.
System RequirementsRequired Operating SystemSupported versions of Windows® will be periodically updated by the web browser provider. Refer to yourbrowser's support page. Supported Browsers for use with Web Maintenance Console• Windows Internet Explorer 11
• Mozilla® Firefox® version 46 or later
• Google Chrome v51 or laterAlways apply the latest updates to your Web browser software. For details, refer to your Web browser’sdocumentation. Only the browsers and browser versions listed above are supported for use with WebMaintenance Console. Browser Setting RequirementsThe following functions must be enabled in the Web browser’s settings to use Web Maintenance Console:• JavaScript
• The ability to download files
• The display of animations
• The display of imagesFor details regarding the above settings, refer to your Web browser’s documentation.
1.3 PC Programming
14 Programming Item List
1.4 Easy Setup WizardDescriptionIn the Easy Setup Wizard, you will configure the mandatory settings required for the PBX. When you login toWeb Maintenance Console for a PBX that is in its initialized, factory default state, the Easy Setup Wizard forthat PBX will launch automatically.
Screen Name Setting item Description InputType Note
Welcome toPanasonicKX-HTS
WebMCLanguage
Selects the language to be usedin Web Maintenance Console.Follow the on-screen instructionsto set the language as necessary.
Select
Area Code Selects the area code to be set inyour country/area. Follow the on-screen instructions to set thearea code.
Select
PasswordSetting
Input the Installer Password (4-16characters, [A–Z, a–z, 0–9]) andinput it in the Re-enter column forconfirmation.
Text1 "1234" cannot beset as thePassword.
1.Date & Time Time Zone Selects the Time Zone. Select
Local Time Selects the time setting. Select
Daylight Saving Selects the Daylight SavingMode.
Radio
2.Numbering Idle Line Access(Local Access)
Specifies the idle trunk accesssetting method.
Radio
ExtensionNumber
Specifies how extension numbersare assigned.
Radio
3.Incoming Call DIL / Doorphone Selects destinations for all portsand all time modes for DIL /Doorphone.
Select
4.Dialling Plan InternationalAccess Code
Selects the international accesscode.
Radio
InternationalAccess CodeOther (6 digits)
When selecting "Other" in theabove setting, set an internationalaccess code of 6 digits or less.
TextNumeric
Local AreaCode (6 digits)
Specifies the local area code. TextNumeric
1.4 Easy Setup Wizard
Programming Item List 15
Screen Name Setting item Description InputType Note
5.IP IP Address forLAN Port-IPAddress
Specifies the IP address for theLAN port.
IPAddress
IP Address forLAN Port-Subnet Mask
Displays the Subnet Mask for theLAN port.
-
Use Built-inDHCP Server ofKX-HTS
Enables the built-in DHCP server. Checkbox
Use Built-inDHCP Server ofKX-HTS-Starting IPaddress
Specifies the start of the IPaddress range. The built-inDHCP server provides an IPaddress within this specifiedrange.
IPAddress
Use Built-inDHCP Server ofKX-HTS-Ending IPaddress
Specifies the end of the IPaddress range. The built-inDHCP server provides an IPaddress within this specifiedrange.
IPAddress
IP Address ofSIP Extension inexisting router
Enables the IP address of SIPExtension in the existing router.
Checkbox
IP Address ofSIP Extension inexisting router-IP Address
Specifies the IP address of SIPExtension in the existing router.
IPAddress
1.4 Easy Setup Wizard
16 Programming Item List
Section 2PBX Configuration
This section provides setting items for programming thePBX.
Programming Item List 17
2.1 Login2.1.1 PBX Configuration
Setting screen (Default)A
B
C
A Uninstalled Slot
B Trunk Slot (Pre-installed)
C Extension Slot (Pre-installed)
Setting screen (Operation example)When a card is inserted to a vacant slot, the insertion is reflected on the display of the screen.When an SIP extension or a SIP trunk is assigned, each button becomes light blue. (E), (F)
ED F
D Port number
E SIP extensions are active
F SIP trunks are active
2.1.2 ExtensionName Description
Extension Opens the Extension port setting screen.2.3.1 PBX Configuration—[2-1] Extension—Port
Extension number Opens the Extension number setting screen.
2.1 Login
18 Programming Item List
2.1.3 TrunkName Description
Trunk Opens the Trunk port setting screen.2.4.1 PBX Configuration—[3-1] Trunk—Port
Trunk number Opens the Trunk number setting screen.
2.1.4 DoorphoneName Description
Doorphone Opens the Doorphone port setting screen.2.3.5 PBX Configuration—[2-5] Extension—Doorphone
Doorphone number Opens the Doorphone port setting screen.2.3.5 PBX Configuration—[2-5] Extension—Doorphone
2.1.3 Trunk
Programming Item List 19
2.2 PBX Configuration—[1] System2.2.1 PBX Configuration—[1-1] System—Date & Time
DescriptionThe date and time of the PBX can be programmed.
Screen / Tab Setting item Description Input Type Note
1.Date &Time-Date& Time
Time Setting Indicates the current dateand time. Values can beentered by selecting theparameter you want tochange the new value.
Select
Automatic TimeAdjustment
Selects the AutomaticTime Adjustment target.
Radio If you select Caller ID,confirm with yourcarrier whethertimestamps areincluded with Caller IDinformation receivedfrom the network.
SNTP Server IPAddress
Sets the IP address of theSNTP server for theAutomatic TimeAdjustment destination.
IP Address This setting isdisplayed only whenAutomatic TimeAdjustment is set to"SNTP".
Time Zone Sets the time zone of thePBX.
Select
1.Date &Time-DaylightSaving
Daylight Saving Check the "Setting" andselects the availablesummer time from thesetting list. Specifies eachsummer time periods.
Check /Select
There will be a timecorrection at 2:00AMon the set day.
2.2 PBX Configuration—[1] System
20 Programming Item List
2.2.2 PBX Configuration—[1-2] System—MOHDescriptionSound files on the programmer’s PC can be installed to the PBX for use as Music on Hold (MOH).
Screen / Tab Setting item Description Input Type Note
2.MOH Music on Hold Selects a sound source forMusic on Hold.
Radio
Upload Music File Sound files on theprogrammer’s PC can beinstalled to each PBX foruse as Music on Hold(MOH).
- • Only WAV files canbe installed, and filenames must notexceed 62characters in length(including the fileextension ".wav").Only use ASCIIcharacters in filenames.
• Files must not belarger than 40 MBon the PC.
Sound on Transfer Shows a sound which isheard during transferringto a destination.
-
Sound on DISA Selects a sound which isheard by a caller usingDISA when calling todialing destinations suchas an extension or trunk,etc. after DISA answers.
Radio
2.2.3 PBX Configuration—[1-3] System—Week TableDescriptionA specific time mode (Day, Lunch or Night) can be selected for operation depending on the time of day. Thetime mode can be switched either automatically or manually.Select the desired switching mode.
Screen / Tub Setting item Description Input Type Note
3.WeekTable
Time ServiceSwitching Mode
Selects the exchangemode (Automatic/Manual)for time service.
Radio
Current Mode Selects a current timeservice mode.
Select
Time Table Check and selects theavailable time service fromthe setting list. Specifieseach time table for startingtime service.
Check /Select
It is possible to set byeach time service.• Day
• Lunch
• Night
2.2.2 PBX Configuration—[1-2] System—MOH
Programming Item List 21
2.2.4 PBX Configuration—[1-4] System—Numbering PlanDescriptionDetails of the extension numbering schemes, trunk line / trunk group access number, feature accessnumbers and Redial numbers can be programmed here.Specify the feature number.
Screen / Tab Setting item Description Input Type Note
4.NumberingPlan-Main
ExtensionNumberingScheme
The leading numbers andthe number of additionaldigits of the extensionnumbers for a maximumof 6 different extensionnumbering schemes canbe programmed.• Dial (1 digit) +
Additional Dial
TextNumeric /Select
Call Park Specifies the Call Parknumber.
TextNumeric
Trunk Line / TrunkGroup
Specifies the outgoingtrunk call feature number,by Trunk Line or TrunkGroup. Additional digits"0" and trunk number areused to make a trunk callusing a certain trunk.Additional digits "#" andtrunk group number areused to make a trunk callusing an idle trunk from acertain trunk group.
TextNumeric
Idle Line Access(Local Access)
Specifies the featurenumber used to make atrunk call by Idle LineAccess (selects an idletrunk automatically).
TextNumeric
Feature Displays one digit to beused for feature numberoperations.
-
Redial Specifies one digit to beused for redial operations.
TextNumeric
2.2.4 PBX Configuration—[1-4] System—Numbering Plan
22 Programming Item List
Screen / Tab Setting item Description Input Type Note
4.NumberingPlan-Features
Setting byExtension-*77
Shows a feature numberof Extension Dial LockSet / Cancel
-
Setting byExtension-*710
Shows a feature numberof FWD/DND Set / Cancel:Call from CO & Extension
-
Setting byExtension-*799
Shows a feature numberof Extension PIN Set /Cancel
-
Setting byManagerExtension-*36
Shows a feature numberof OGM Record / Clear /Playback
-
Setting byManagerExtension-*55
Shows a feature numberof Door Open
-
Setting byManagerExtension-*780
Shows a feature numberof Time Service (Day /Lunch / Night) Switch
-
Setting byManagerExtension-*#
Shows a feature numberof System Setting
-
Call by Extension-**
Shows a feature numberof System Speed Dialing
-
Call by Extension-*33
Shows a feature numberof Paging
-
Call by Extension-*40
Shows a feature numberof Group Call Pickup
-
Call by Extension-*41
Shows a feature numberof Directed Call Pickup
-
Call by Extension-*47
Shows a feature numberof Walking COS / AccountCode
-
4.NumberingPlan-QuickDial
Dial (2 digits) Specifies Quick Dial by 1or 2 digits.
Dial1 Do not use thenumbers alreadyspecified in "Dial" forthe Main tabs. Do notuse the "*" at the firstdigit.
Phone Number (32digits)
Specifies the number tobe actually dialed byQuick Dial specified in theabove.
Specifies the length oftime that an extension-to-trunk / extension-to-extension call can bemaintained before beingdisconnected.
Select
2.2.5 PBX Configuration—[1-5] System—Timers
24 Programming Item List
2.2.6 PBX Configuration—[1-6] System—System OptionsDescriptionVarious system settings can be programmed.
Screen / Tab Setting item Description Input Type Note
6.SystemOptions-Feature
Trunk AccessPriority
It can be assigned apriority for Idle LineAccess. When making atrunk call by Idle LineAccess, the PBX willsearch trunk for an idletrunk according to thepriority assigned here.
Radio
Reservedconcurrent trunkcall
Selects the trunk numberto prioritize for concurrenttrunk call reservation.
Select
Reservedconcurrent G.729call
Selects the assignmentnumber for the number ofconcurrent G.729 calls.
Select
ForcedAssignment to SIPExtension Port
Setting to change forciblyfrom an analog port to anSIP port.
Radio
Ring Tone Pattern-Trunk
Selects the pattern of thering tone for receiving atrunk call.
Radio
Ring Tone Pattern-Extension/Doorphone
Selects the pattern of thering tone for receiving anextension call.
Radio
6.SystemOptions-Audio Gain
Sending Source Selects the sendingsource for audio gain.
DescriptionSettings can be made for each extension port. Click the "Edit" button located next to the extension numberto enable editing of the setting values.
Screen / Tab Setting item Description Input Type Note
1.Port-Main Extension Number Specifies the extensionnumber of the extension.
TextNumeric
Edit Button Clicking this buttonenables the editing ofsettings for the extensionnumber.
-
Extension Name Specifies the name of theextension.
TextLCDHDV
Attribution Sets the port to SIP orAnalog.
Select
FAX Connection Enables the faxconnection.
Radio
Manager Sets the managerauthority for the portextension.
Radio
TRS Level (COS) Specifies the TollRestriction (TRS) level formaking calls in each timeservice mode, speed dial,and dial lock.
Radio
Remote Dial Lock Remote outgoing callrestriction.
Radio
Call Forward to CO Enables the forwarding ofcalls to trunks.
Radio
Trunk Call Block Sets the trunk connectionrestriction to trunks (CO1to CO8) from the portextension.
Radio
Call from DISA Enables the reception ofcalls from DISA.
Radio
Call Pickup Deny Specifies whether callscan be picked up by otherextensions.
Radio Allow: Allows otherextension users to pickup calls to yourextensionDeny: Prevents otherextension users frompicking up calls to yourextension
2.3 PBX Configuration—[2] Extension
28 Programming Item List
Screen / Tab Setting item Description Input Type Note
Walking COS Allows the Walking COSfeature to be used from aremote location (inside thePBX, or outside the PBXusing DISA).• by Other Extension
• by DISA
Radio
Voice Mail Sets the number of theVoice Mail recording andthe recording time for avoice mail.• Recording Number
• Recording Time (s)
UnsignedNumber
CLIP Specifies the number usedas the CLIP number forSIP carrier -1 or SIPcarrier - 2.
TextNumeric
1.Port-AnalogExtension
Extension Number Specifies the extensionnumber of the extension.
TextNumeric
Edit Button Clicking this buttonenables the editing ofsettings for the extensionnumber.
-
Caller ID SignalSend
Enables the extension tosend Caller ID information.
Radio
1.Port-SIPExtension
Extension Number Specifies the extensionnumber of the extension.
TextNumeric
Edit Button Clicking this buttonenables the editing ofsettings for the extensionnumber.
-
SIP RegistrationStatus
Indicates the SIPextension registrationstatus.
-
SIP User Name Specifies the SIP username of the SIPextension.
Text3
RegistrationPassword
Specifies the passwordused for registering a SIPExtension to the PBX.
Text3
Current IP Address Indicates the current IPaddress of the SIPExtension (referenceonly).
-
2.3.1 PBX Configuration—[2-1] Extension—Port
Programming Item List 29
Screen / Tab Setting item Description Input Type Note
Current MACAddress
Indicates the current MACaddress of the SIPExtension (referenceonly).
-
Phone Location Specifies the type ofextension connected tothe port.
Radio Local: The extension islocated on the samenetwork as the PBX(standardconfiguration).Remote/Remote(G.729): The extension isaccessing the PBXremotely (up to 8extensions).
Alive Check Enables the alive-checkfeature.
Select
Alive Check -Interval
Selects the interval of thealive-check feature.
Select
Packet SamplingTime (ms)
Specifies the time intervalbetween measurements(samples) of sound dataduring a conversation. Thesmaller this number, thehigher the quality of thetransmitted sound.
Select
DTMF Selects the DTMF of a SIPextension.
Select
Video Support Enables the video supportfeature.
Radio
Call Limit Selects the concurrent callsession number.
Select
2.3.1 PBX Configuration—[2-1] Extension—Port
30 Programming Item List
2.3.2 PBX Configuration—[2-2] Extension—PhoneDescriptionSettings can be made for each telephone. Click the "Edit" button located on the side of an item to enableediting of the setting values.
Screen / Tab Setting item Description Input Type Note
2.Phone Extension Number Specifies the extensionnumber of the extension.
Select Only the Installer levelaccount can changethis setting.
Web User Account-ID
Specifies an Extensionuser ID (Extensionnumber)
Text5
Web User Account-Password
Indicates an extensionuser password as "****".Click an "Edit" button, andspecified a password.
Text1
PIN Specifies the user'sextension PIN.
TextNumeric
Contact-Phone(Home)
Specifies the user’s hometelephone phone number.
Dial1
Contact-Phone(Mobile1)
Specifies the user’smobile telephone phonenumber.
Dial1
Contact-Phone(Mobile2)
Specifies the user’smobile telephone phonenumber.
Dial1
Contact-EmailAddress
Specifies the user’s e-mailaddress.
Text Email
FWD/DND-FWD/DND Type
Specifies the FWD/DNDtype of incoming calls.
Select
FWD/DND-DestinationNumber
Specifies the FWD/DNDdestination.
RadioDial1
When select the"Other" radio button toset another destinationwithin 32 digits.
FWD/DND-FWDNo Answer Time
Specifies the length oftime that an incoming callrings at the extensionbefore the call isforwarded.
Select It is possible to set byeach time service.• Day
• Lunch
• Night
FWD/DND-Transferred call noanswer option
Selects the action to takewhen a call is transferredbecause there was noanswer.
Select
2.3.2 PBX Configuration—[2-2] Extension—Phone
Programming Item List 31
Screen / Tab Setting item Description Input Type Note
Voice Mail-SendEmail whenMessage is left
Specifies the notificationto a subscriber when anew message is recordedin his or her mailbox by e-mail.
Radio When selecting"Enable", send VoiceMail recording noticeemail to "Contact-Email Address"
Voice Mail-DeleteMessage afterEmail
To specify if a sent voicemessage is deleted fromthe Voice Messagesystem after it is sent bye-mail, select "Enable" forDelete After Send (VoiceFile).
Radio If voice message filesare set to be deletedafter they are sent bye-mail, be aware that adeleted file cannot berecovered in the eventthat the e-mail is notsent successfully.
Call Waiting Specifies whether toreceive call waitingnotifications for calls froma trunk, an extension,doorphone calls, and callsvia an incoming calldistribution group.
Radio
Extension DialLock (Local)
Specifies the extensionlock or unlock. The pre-programmed TRS levelwill be applied to theextension when "Lock" isselected.
Select
2.3.3 PBX Configuration—[2-3] Extension—Flexible ButtonsDescriptionEach flexible button can be customized to allow one-touch access to a certain feature.
Screen / Tab Setting item Description Input Type Note
3.FlexibleButtons
Extension Number Specifies the extensionnumber of the extension.
Select Only the Installer levelaccount can changethis setting.
Telephone Indicates the type oftelephone and the keyinformation.
-
Flexible Buttons-Key Location
Indicates the locationnumber of flexible buttons.
-
Flexible Buttons-Type
Specifies the feature to beassigned to the flexiblebutton.
Select
Flexible Buttons-CO Line Number/Extension Number/Dial
2.3.4 PBX Configuration—[2-4] Extension—Extension GroupDescriptionExtension group settings can be programmed.
Screen / Tab Setting item Description Input Type Note
4.ExtensionGroup
Group Number Selects the floatingextension number of theextension group that youwant to display. Theinformation relating to theselected group is shownbelow.
Select
4.ExtensionGroup-GroupSetting
Group Number Specifies the floatingextension number of theextension group.
TextNumeric
Group Name Specifies the extensiongroup name.
Text LCD
DistributionMethod
Selects the distributionmethod of the extensiongroup.
Select
FWD-FWD Type Selects the FWD type ofthe extension group.
Select
FWD-DestinationNumber
Specifies the destinationnumber of the extensiongroup.
Dial1
2.3.4 PBX Configuration—[2-4] Extension—Extension Group
Programming Item List 33
Screen / Tab Setting item Description Input Type Note
FWD-FWD NoAnswer Time
Selects the length of timethat an incoming call ringsat the extension before thecall is forwarded.
Select It is possible to set byeach time service.• Day• Lunch• Night
FWD-Transferredcall no answeroption
Selects the action to takewhen a call is transferredbecause there was noanswer.
Select
Paging Type Selects the paging type ofthe extension group.
Select
4.ExtensionGroup-Extension ofMember
Extension No.Setting
Edits the member of theextension group.
-
Extension ofMember
In the edit dialog, you canselect up to 24 extensionnumbers that have beenadded to the extensiongroup.
Select
2.3.5 PBX Configuration—[2-5] Extension—DoorphoneDescriptionDoorphone settings can be programmed.
Screen / Tab Setting item Description Input Type Note
5.Doorphone Extension Numberof Doorphone
Specifies the extensionnumber of the doorphone1 or 2.
TextNumeric
Name Specifies the name of thedoorphone 1 or 2.
Text LCD
Doorphone CallDestination
Selects the call destinationfrom the doorphone 1 or 2.
Select It is possible to set byeach time service.• Day• Lunch• Night
Doorphone RingDuration
Selects the ring durationfrom the doorphone.
Select
Door OpenDuration
Selects the length of timethat a door is unlocked.
Select
2.3.5 PBX Configuration—[2-5] Extension—Doorphone
34 Programming Item List
2.3.6 PBX Configuration—[2-6] Extension—Analog SLT PropertyDescriptionAnalog SLT property settings can be programmed.
Screen / Tab Setting item Description Input Type Note
6.Analog SLTProperty
SLT Off Hook Time Selects the SLT off hooktime.
Select
SLT FlashDetection
Selects the SLT flashdetection.
Select
Flash Timing - Min. Selects the minimum flashtiming.
Selects whether toperform silence monitoringduring a call. If there areno RTP packets sent orreceived during the pre-programmed time, the callwill be disconnected.
Select RTP silence detectiondoes not apply tovideo calls on P2P.
DescriptionSettings can be made for each trunk port. Click the "Edit" button located next to the trunk number to enableediting of the setting values.
Screen / Tab Setting item Description Input Type Note
1.Port-Main Attribution Selects the attributes of a trunkport.
Select
Trunk Group Specifies the trunk groupnumber to which the trunkbelongs.
Select
1.Port-Analog -Basic
Dialing Mode Selects the type of signal usedto dial out to the analog trunk.
Radio
Caller ID Detection Enables the PBX to detect aCaller ID signal from theanalog trunk.
Radio
Caller ID DetectionPattern
Selects the type of Caller IDsignaling provided by thetelephone company.
Radio
Reverse Detection Selects the type of trunk callfor which the reverse signalfrom the telephone company isdetected.
Radio
1.Port-Analog -CPC Detection
CPC Signal DetectionTime Outgoing
Specifies the length of timerequired by the PBX to detect aCPC signal on outgoing trunkcalls before disconnecting theline.
Select
CPC Signal DetectionTime Incoming
Specifies the length of timerequired by the PBX to detect aCPC signal on incoming trunkcalls before disconnecting theline.
Select
1.Port-Analog -DISA
DISA Tone Detection -Silence
Enables the disconnection of aDISA-originated trunk-to-trunkcall by silence detection.
Radio
DISA Tone Detection -Continuous
Enables the disconnection of aDISA-originated trunk-to-trunkcall by continuous signaldetection.
Radio
DISA Tone Detection -Cyclic
Enables the disconnection of aDISA-originated trunk-to-trunkcall by cyclic signal detection.
Radio
2.4 PBX Configuration—[3] Trunk
38 Programming Item List
Screen / Tab Setting item Description Input Type Note
1.Port-Analog -Dialing
Pulse Speed Selects the speed at whichpulse dials are sent to theanalog trunk.
Select
DTMF Width Selects the length of the DTMFtone sent to the analog trunk.
Select
Disconnect Time Specifies the length of timeafter a trunk is disconnected,during which the PBX cannotseize the line.
Select
1.Port-Analog -Caller ID
Caller ID(FSK) -Carrier Detection
Enables the PBX to detect thecarrier when receiving CallerID.
Radio
Caller ID(FSK) - ENDDetection
Selects the method used todetect the end of Caller IDinformation.
Radio
Caller ID(FSK) -Header Examination
Enables the PBX to check theheader of received Caller IDinformation.
Radio
Caller ID(FSK) -Detection Start Timer
Specifies the length of timethat the PBX waits beforeattempting to detect Caller IDinformation, after receiving acall. To enable this setting,Caller ID Detection Patternshould be set to FSK.
Select
Caller ID(FSK) -Detection Timer
Specifies the total timerequired by the PBX to detectCaller ID information.
Select
Caller ID(DTMF) -Start Code 1
Selects the DTMF code usedto detect the beginning of aCaller ID series.
Select
Caller ID(DTMF) -Start Code 2
Selects the DTMF code usedto detect the beginning of aCaller ID series.
Select
Caller ID(DTMF) -Information Start Code
Selects the DTMF code usedto detect the beginning of theinformation segment of a CallerID series.
Select
Caller ID(DTMF) - EndCode
Selects the DTMF code usedto detect the end of a Caller IDseries.
Select
Caller ID Header[03] Selects the type of the 3rdheader in a Caller ID signal.
Radio
2.4.1 PBX Configuration—[3-1] Trunk—Port
Programming Item List 39
Screen / Tab Setting item Description Input Type Note
1.Port-Analog -Collect CallReject (forBrazil)
Mode Enables the PBX toautomatically reject collectcalls. This setting is only forusers in Brazil.
Radio
Wait Time Selects the length of time thatthe PBX waits before sendinga flash signal to reject a collectcall. This setting is only forusers in Brazil.
Select
Flashing Time Selects the length of the flashsignal that the PBX sends toreject a collect call. This settingis only for users in Brazil.
Select
2.4.2 PBX Configuration—[3-2] Trunk—DILDescriptionDIL settings can be programmed for the trunk.
Screen / Tab Setting item Description Input Type Note
2.DIL Day Specifies the DILdestination in the "Day"mode of time service.
Select
Lunch Specifies the DILdestination in the "Lunch"mode of time service.
Select
Night Specifies the DILdestination in the "Night"mode of time service.
Select
2.4.3 PBX Configuration—[3-3] Trunk—DDIDescriptionDDI settings can be programmed for the trunk.
Screen / Tab Setting item Description Input Type Note
3.DDI Dialing Plan - DDI Selects the suitability of aDDI incoming call.
Select
Dialing Plan -Remove Digit
Specifies the number ofleading digits to beremoved from theincoming called numberfor DDI distribution.
Select
Dialing Plan -Additional Dial
Specifies the number tobe added to the incomingcalled number in the placeof the removed digits forDDI distribution.
Dial1
2.4.2 PBX Configuration—[3-2] Trunk—DIL
40 Programming Item List
Screen / Tab Setting item Description Input Type Note
DDI Table - DDINumber
Specifies the DDI number. Dial1
DDI Table - Name Specifies the name for theDDI number.
Text LCD
DDI Table -Destination - Day
Specifies the DDIdestination in the "Day"mode of time service.
Select
DDI Table -Destination -Lunch
Specifies the DDIdestination in the "Lunch"mode of time service.
Select
DDI Table -Destination - Night
Specifies the DDIdestination in the "Night"mode of time service.
Select
2.4.4 PBX Configuration—[3-4] Trunk—Caller ID Modify & BlockDescriptionSettings can be made for modifying and blocking Caller ID.
Screen / Tab Setting item Description Input Type Note
4.Caller IDModify &Block
Incoming CallBlock when NoCaller ID
When there is no CallerID, refuse incoming call.
Radio
Caller ID ModifyTable - Area Code(6 digits)
Specifies the leadingnumber (area code) tolook for in the incomingcaller’s number.
TextNumeric
Caller ID ModifyTable - RemovedNumber of Digits
Specifies the number ofdigits to be removed fromthe beginning of theincoming caller’s number.
Select
Caller ID ModifyTable - AddedNumber (4 digits)
Specifies the number tobe added to the incomingcaller’s number in theplace of the removeddigits.
Dial1
Caller ID Modify byLength of Digits -Minimum Caller IDDigits
Selects minimum numberof caller ID digits.
Select The value of Nationalmust be smaller thanthat of International.
Caller ID Modify byLength of Digits -Added Number (6digits)
Specifies the addednumber.
Dial1
Analog Trunk Enables Caller ID Modifyby Length of Digits for theanalog trunk.
Radio
2.4.4 PBX Configuration—[3-4] Trunk—Caller ID Modify & Block
Programming Item List 41
Screen / Tab Setting item Description Input Type Note
SIP Trunk Enables Caller ID Modifyby Length of Digits for theSIP trunk.
Radio
2.4.5 PBX Configuration—[3-5] Trunk—DISADescriptionDISA settings can be programmed for the trunk.
Screen / Tab Setting item Description Input Type Note
5.DISA-Message
Floating ExtensionNumber
Specifies the floatingextension number of theOGM.
TextNumeric
Name Specifies the name of theOGM.
Text5
1 Digit AADestination(ExtensionNumber) - Dial0
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial1
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial2
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial3
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial4
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial5
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial6
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial7
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
2.4.5 PBX Configuration—[3-5] Trunk—DISA
42 Programming Item List
Screen / Tab Setting item Description Input Type Note
1 Digit AADestination(ExtensionNumber) - Dial8
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
1 Digit AADestination(ExtensionNumber) - Dial9
Specifies the destinationfor each DISA AutomatedAttendant (AA) number.
Select
No Dial Destination Selects anotherdestination when there isno dialing after DISAanswers.
Select
FAX Extension Specifies the extensionnumber to which totransfer a call when a faxsignal is detected.
Select
Busy Mode -Mode Selects an operationMode when the incomingcall destination throughDISA is Busy.
Select
Busy Mode - OGM Selects voice guidance forwhen the operation Modeis OGM in case a line isbusy.
Select This setting can beselected if OGM isselected for the BusyMode setting.
5.DISA-System
Timer - DelayedAnswer Timer (s)
Specifies the length oftime that the caller hears aringback tone beforehearing an OGM.
Select
Timer - Mute &OGM Start Timerafter answering (s)
Specifies the length oftime until the caller hearsan OGM after reaching theDISA line.
Select
Timer - No DialIntercept Timer (s)
Specifies the length oftime after the OGMfinishes playing in whichthe caller must begindialing before the call isredirected to the operator.
Select
Timer - 2nd DialTimer for AA (s)
Specifies the length oftime in which the callermust dial the second digitbefore the DISA AAService activates.
Select
DISA Cyclic Tone -DISA Cyclic ToneDetection
Selects the DISA cyclictone detection type.
Select
2.4.5 PBX Configuration—[3-5] Trunk—DISA
Programming Item List 43
Screen / Tab Setting item Description Input Type Note
DISA Cyclic Tone -Tone on MaximumTime (ms)
Selects the tone-onmaximum time.
Select This setting can beselected if DISA CyclicTone is selected forthe Option.
DISA Cyclic Tone -Tone off MaximumTime (ms)
Selects the tone-offmaximum time.
Select This setting can beselected if DISA CyclicTone is selected forthe Option.
DISA Cyclic Tone -Repeating Timesof ON/OFF forDetection
Selects the number oftimes of tone on/off todetermine detection.
Select This setting can beselected if DISA CyclicTone is selected forthe Option.
2.4.6 PBX Configuration—[3-6] Trunk—Analog CO PropertyDescriptionAnalog CO property settings can be programmed.
Screen / Tab Setting item Description Input Type Note
6.Analog COProperty
Caller ID Waiting toReceive
Specifies the length oftime that the PBX waits toreceive Caller ID from ananalog trunk.
Select
Outgoing GuardTime
Specifies the length oftime after a trunk isdisconnected, duringwhich the PBX cannotseize the line.
Select
First Dial Timer(CO)
Specifies the minimumtime that the PBX waitsafter seizing a trunk,before sending the dialeddigits to the telephonecompany.
Select
Bell Detection -Bell Start DetectionTimer
Specifies the minimumlength of a bell signal thatcan be recognized by thePBX as the bell signalsent from the telephonecompany, before the PBXdetects an arriving call.
Select
Bell Detection -Bell Off DetectionTimer
Specifies the duration ofthe bell off detection timer.
Select
Pulse / DTMF Dial- DTMF Inter-digitPause
Specifies the length of theDTMF inter-digit pause.
Select
2.4.6 PBX Configuration—[3-6] Trunk—Analog CO Property
44 Programming Item List
Screen / Tab Setting item Description Input Type Note
Pulse / DTMF Dial- Pulse Inter-digitPause
Specifies the length of thepulse inter-digit pause.
Select
Low Speed PulseDial - Pulse %Break
Specifies the % break fora low speed pulse dial.
Select
Low Speed PulseDial - Break Width
Specifies the maximumlength of the break signalin a low speed pulse dial.
Select This feature isavailable when Otheris selected in Pulse %Break.
Low Speed PulseDial - Make Width
Specifies the minimumlength of the make signalin a low speed pulse dial.
Select This feature isavailable when Otheris selected in Pulse %Break.
High Speed PulseDial - Pulse %Break
Specifies the % break fora high speed pulse dial.
Select
High Speed PulseDial - Break Width
Specifies the maximumlength of the break signalin a high speed pulse dial.
Select This feature isavailable when Otheris selected in Pulse %Break.
High Speed PulseDial - Make Width
Specifies the minimumlength of the make signalin a high speed pulse dial.
Select This feature isavailable when Otheris selected in Pulse %Break.
High Speed PulseDial - Pulse Type
Selects the type of pulsedial transmissionappropriate to your area.
Radio
2.4.7 PBX Configuration—[3-7] Trunk—SIP Trunk PropertyDescriptionSIP trunk property settings can be programmed.
Screen / Tab Setting item Description Input Type Note
7.SIP TrunkProperty-Common
DNS SRV RecordResolve Ability
Specifies whether torequest that the DNSserver translates domainnames into IP addressesusing the DNS SRVrecord.
Radio
Register - RegisterSending Interval(s)
Specifies the maximumlength of interval time afterwhich the PBX sends theREGISTER message.
UnsignedNumber
Register - RegisterResending Interval(s)
Specifies the interval timefor resending theREGISTER message.
Screen / Tab Setting item Description Input Type Note
1.WANSetting
WAN Setting -WAN Name
Provides information ofWAN Name configured.
-
WAN Setting -WAN Channel
Provides information oflayer-2 WAN channelconfigured.
-
WAN Setting -Type
Provides informationabout type of WAN suchas PPPoE or DHCP Clientor Fix IP.
-
WAN Setting -Default WAN
This option allows the userto configure a defaultroute in system. Thechosen WAN will be userfor default route.
Radio
Modify Button Clicking this button allowsyou to modify the WANsettings.
-
1.WANSetting -WAN
WAN TYPE WAN TYPE Select
WAN connectionName
WAN connection Name Text(excluding< > ;)
IP address,by yourISP
To specify the IP Addressof the PBX’s WAN link.
IP Address This feature isavailable when Fix IPis selected in WANType.
Subnet Mask To specify the SubnetMask of the PBX’s WANlink.
SubnetMask3
This feature isavailable when Fix IPis selected in WANType.
ISP GatewayAddress
To specify the Gatewayaddress of the PBX'sWAN.
IP Address This feature isavailable when Fix IPis selected in WANType.
User Name To ensure a username forPPPoE session used forauthentication.
TextRouter2
This feature isavailable when PPPoEis selected in WANType.
Password To ensure a password forPPPoE session used forauthentication.
Text RouterPwd2
This feature isavailable when PPPoEis selected in WANType.
3.2 Network Configuration—[3] WAN
Programming Item List 57
Screen / Tab Setting item Description Input Type Note
Please retype yourpassword
To enter the samepassword again toreconfirm.
Text RouterPwd2
This feature isavailable when PPPoEis selected in WANType.
Service Name PPP Service Name(optional)
TextRouter2
This feature isavailable when PPPoEis selected in WANType.
AccessConcentratorName
PPP Access concentratorName (optional)
TextRouter2
This feature isavailable when PPPoEis selected in WANType.
Relay LAN sitePPPoE session
This feature allows toenable/disable a PPPoErelay session.
Check This feature isavailable when PPPoEis selected in WANType.
MTU:(1400-1500) To enter the maximumtransfer unit size ofPPPoE frames.
UnsignedNumber
This feature isavailable when PPPoEis selected in WANType.
PPP Option Choose the option formthe drop down list. Theavailable options are, AutoConnect, Dial-On-Demandand Manual Connect
Select This feature isavailable when PPPoEis selected in WANType.
Maximum IdleTime
To enter the maximum idletime.
TextNumeric
This feature isavailable when Dial-On-demand(DoD) isselected in PPPOption.Available values: 0 -99999
Static DNS This option allows the userto configure primary/secondary DNS servers ofthis WAN connection.
Check When this feature isset to ON, the addressof the DNS serverreceived from PPPoEserver is not available.
Primary DNSServer
Specifies the primary DNSserver for the WAN.
IP Address This feature isavailable when ON isselected in Static DNS.If the address of theprimary DNS server isreceived from PPPoEsever beforespecifying, it isdisplayed as default.
3.2.1 Network Configuration—[3-1] WAN—WAN Setting
58 Programming Item List
Screen / Tab Setting item Description Input Type Note
Secondary DNSServer
Specifies the secondaryDNS server for the WAN.
IP Address This feature isavailable when ON isselected in Static DNS.If the address of thesecondary DNS serveris received fromPPPoE sever beforespecifying, it isdisplayed as default. Ifonly the address of theprimary DNS server isreceived from PPPoEsever beforespecifying, it isdisplayed as default.
Option—SIP QoS-DSCP
Selects the SIP QoS-DSCP.
Select • DSCP value isspecified accordingto the value set foreach protocol of theWAN port ofKX-HTS series. Incase of using anexisting LAN,consult yournetworkadministrator. Incase of using a SIPtrunk, consult yourSIP serviceprovider.
• For DSCP valuesettings for KX-HDVseries, KX-NTVseries and general-purpose SIP phonesconnected to thesame network, referto thecorrespondingmanuals.
Option—RTP QoS-DSCP
Selects the RTP QoS-DSCP.
Select
Option—VideoQoS-DSCP
Selects the video QoS-DSCP.
Select
Option—OthersQoS-DSCP
Selects the Others QoS-DSCP.
Select
Option—BandwidthLimitation forOthers
Specifies whether toenable the bandwidthlimitation.
Select
3.2.1 Network Configuration—[3-1] WAN—WAN Setting
Programming Item List 59
3.2.2 Network Configuration—[3-2] WAN—WAN StatusThe WAN status can be confirmed.
Screen / Tab Setting item Description Input Type Note
2.WANStatus
No. WAN Number -
WAN Channel For the currentlyconfigured WAN interface,this gives the layer-2 WANchannel information.
-
Connection Type The type of connectionmode in which the PBX'sis configured.
-
Status Displays the connectionstatus of the WAN.
- Connecting...:– IP address is not
received whenConnection Type isDHCP Client.
– Connecting to PPPrink whenConnection Type isPPPoE.
Connected:– IP address is
received whenConnection Type isDHCP Client.
– Connection Type isFix IP
– Connected to PPPrink whenConnection Type isPPPoE.
Disconnecting:– Released the
current lease whenConnection Type isDHCP Client.
– Disconnected toPPP rink whenConnection Type isPPPoE.
3.2.2 Network Configuration—[3-2] WAN—WAN Status
60 Programming Item List
Screen / Tab Setting item Description Input Type Note
IP Displays the IP address inuse.
- Unconfigured:– IP address is not
received whenConnection Type isDHCP Client.
– IP address is notreceived whenConnection Type isPPPoE.
Netmask Displays the netmask inuse.
- Unconfigured:– IP address is not
received whenConnection Type isDHCP Client.
– IP address is notreceived whenConnection Type isPPPoE.
Connection Name Displays the configuredconnection name.
-
GatewayInformation
Provides informationabout the gateway.
-
DNS Information Provides informationabout the primary andsecondary DNS.
- DNS chosen in theDefault WAN is priorityfor display.
3.2.2 Network Configuration—[3-2] WAN—WAN Status
Programming Item List 61
3.2.3 Network Configuration—[3-4] WAN—DDNSThe DDNS settings for the WAN can be programmed. In order to reflect the menu setup, you must set"Enable DDNS Support" to Enable.
Screen / Tab Setting item Description Input Type Note
4.DDNS Enable DDNSSupport
Check box to enableDDNS support in the PBX.
Check
WAN Interface WAN Interface name fromthe dropdown for DDNSresolution. The DDNSagent running in the PBXkeeps track of changes inIP address of chosenWAN and informs DNSservice provider.
Select
DDNS Server DDNS Server Select Radio
Host Name Host name registered withDDNS Service provider.This is part of FQDN usedfor accessing the host.
TextRouter3
User Name Registered user namewith DDNS serviceprovider.
TextRouter3
Password Registered password withDDNS service provider.
Clicking this button allowsyou to modify theAdvanced Radio Settings.For normal operation ofWLAN AP functionality,changing the values inAdvanced Settings is notrecommended.
-
3.5 Network Configuration—[6] Wireless
66 Programming Item List
Screen / Tab Setting item Description Input Type Note
1.RadioSettings -WLANAdvancedRadioSettings
WLAN GeneralConfig - Preamble
Preamble Type. Select
WLAN GeneralConfig - BeaconInterval
Beacon interval inmilliseconds.
UnsignedNumber
WLAN GeneralConfig - DTIMInterval
Delivery Traffic IndicatorMessage (DTIM) intervalin number of beacons.
UnsignedNumber
WLAN GeneralConfig - PowerLevel
Power level at whichWLAN AP should operate.
Select
WLAN GeneralConfig - RTSThreshold
Request to Send in Bytes. UnsignedNumber
WLAN GeneralConfig - StaticRate in Mbit/s
Static Rate for WLAN APin Mbps.
Select If the user changesany of the followingsettings, this settingwill be reset:• Operational Mode
• Channel Bandwidth
• Guard Interval
802.11n Settings -Length of MPDUaggregation
Length of MPDUaggregation in bytes.
Select
802.11n Settings -STBC
Space Time Block Coding Select
3.5.2 Network Configuration—[6-2] Wireless—Main AP SettingsThe main AP settings can be programmed.
Screen / Tab Setting item Description Input Type Note
2.Main APSettings -WLAN MainSettings
AP Name Name of Access Point -unique identifier.
-
SSID Service Set Identifier -public name of WLAN orNetwork.
-
Type Type (AP) -
Security Type of Security. -
Encryption Type of Encryption. -
Authentication Type of Authentication. -
Mode Operation Mode. -
Status Status of AP - UP orDOWN.
-
3.5.2 Network Configuration—[6-2] Wireless—Main AP Settings
Programming Item List 67
Screen / Tab Setting item Description Input Type Note
Modify Button Clicking this button allowsyou to modify a WLAN APconfiguration.
-
2.Main APSettings -WLAN APConfigurationSettings
SSID Service Set Identifier ofAP.
Text RouterSSID
AP Name AP Name - UniqueIdentifier within the PBX.
TextRouter2
Maximum ClientLimit
Indicates the maximumnumber of stations thatcan connect to thecorresponding AP.
UnsignedNumber
Enable HiddenSSID Mode
Whether to hide SSID inbeacon frames.
Check
AP Isolation Enables or disables theAP Isolation feature.
Select
3.5.3 Network Configuration—[6-3] Wireless—Security SettingsThe wireless security settings can be programmed.
Screen / Tab Setting item Description Input Type Note
3.SecuritySettings -WLANSecuritySettings
AP name Displays the AP name. Label To change this setting,refer to 3.5.2 NetworkConfiguration—[6-2]Wireless—Main APSettings.
SSID Displays the SSID. Label To change this setting,refer to 3.5.2 NetworkConfiguration—[6-2]Wireless—Main APSettings.
Security Selection- Security
Selects the Security. Select
Security Selection- AuthenticationType
Selects the authenticationtype.
Select This feature isavailable when thefollowing settings arespecified:• Security: Basic and
Screen / Tab Setting item Description Input Type Note
WEP Key Settings- Key Index
Selects the key index. Select This feature isavailable when WEP isselected in EncryptionType.
WEP Key Settings- Encryption Level
Selects the encryptionlevel.
Select This feature isavailable when WEP isselected in EncryptionType.If you change the thisfeature setting, theWEP Key 1 - 4 will bereset to default.
WEP Key Settings- WEP Key Type
Selects the WEP key type. Select This feature isavailable when WEP isselected in EncryptionType.If you change the thisfeature setting, theWEP Key 1 - 4 will bereset to default.
WEP Key Settings- WEP Key 1*1
Specifies the WEP key 1. Text ASCIIText HEX
This feature isavailable when WEP isselected in EncryptionType.
WEP Key Settings- WEP Key 2*1
Specifies the WEP key 2. Text ASCIIText HEX
This feature isavailable when WEP isselected in EncryptionType.
WEP Key Settings- WEP Key 3*1
Specifies the WEP key 3. Text ASCIIText HEX
This feature isavailable when WEP isselected in EncryptionType.
WEP Key Settings- WEP Key 4*1
Specifies the WEP key 4. Text ASCIIText HEX
This feature isavailable when WEP isselected in EncryptionType.
WPA/WPA2Settings - Re-KeyInterval
Specifies the re-keyinterval.
UnsignedNumber
This feature is notavailable when Basicis selected in Security.
Personal Settings -Use PSK
Specifies whether to usepre-shared keys.
Check This feature isavailable whenPersonal is selected inAuthentication Type.
Personal Settings -Pre-Shared Key(64 digits)
Specifies the pre-sharedkey.
Text HEX This feature isavailable whenPersonal is selected inAuthentication Type.
Check When this featuresetting changes toOFF, Internal RegistrarSupport is set to OFF.When this featuresetting changes to ON,Internal RegistrarSupport is set to ON.
Internal Registrar Support. - This feature is set toON, when WirelessLAN Setup Enable isset to ON.This feature is set toOFF, when WirelessLAN Setup Enable isset to OFF.
Screen / Tab Setting item Description Input Type Note
1.NATSettings
NAT Settings Used to Enable or Disablethe Network AddressTranslation feature.
Radio
3.7.2 Network Configuration—[8-2] NAT—Virtual ServerDescriptionThe virtual server settings for NAT can be programmed.
Screen / Tab Setting item Description Input Type Note
2.VirtualServer -VirtualServer
Add Button Clicking this button adds avirtual serverconfiguration.
-
Application Name Configured ApplicationName for Virtual Serverrule.
-
Private IP Private IP address ofVirtual Server rule.
-
Remote IP Remote IP address ofVirtual Server rule.
-
Private Start Port Private Port startingrange.
-
Private End Port Private Port ending range.For a single port the startand end are both thesame
-
Protocol Virtual Server protocol -TCP or UDP or Both i.e.TCP/UDP.
-
Public Start Port Public Port starting range. -
Public End Port Public Port ending range.For a single port the startand end are both thesame
-
Enable To enable the specifiedentry of the virtual server.
-
WAN Interface WAN interface on whichthe Virtual Server rule isconfigured.
-
3.7 Network Configuration—[8] NAT
76 Programming Item List
Screen / Tab Setting item Description Input Type Note
Modify Button Clicking this button allowsyou to modify a virtualserver configuration.
-
2.VirtualServer -ConfigureVirtualServer
Application Name -Custom application
Custom application Text Up to 40 characters.
Protocol Specify Virtual Serverprotocol - TCP or UDP orBoth i.e. TCP/UDP.
Select
Private IP Specify Private IP addressof Virtual Server rule.
IP Address If a character that cannot be used is entered,this feature is set to255.255.255.255.
Remote IP Specify Remote IPaddress of Virtual Serverrule.
IP Address If 255.255.255.255 isentered, this feature isset to 0.0.0.0.
Public Port Range Specify Public Port range. UnsignedNumber
Private Port Range Specify Private Portrange. For a single port,the start and end are boththe same.
UnsignedNumber
This feature ischanged in conjunctionwith Public Port Rangesetting.
Enable To enable the specifiedentry of the virtual server,select the check box.
Check
WAN Interface Specify WAN interface onwhich the Virtual Serverrule is configured.
Select
3.7.3 Network Configuration—[8-3] NAT—DMZDescriptionThe DMZ settings for NAT can be programmed.
Screen / Tab Setting item Description Input Type Note
3.DMZ Enable To enable or disable theDMZ setting of the PBX.Select the check box toenable.
Check
IP Address ofVirtual DMZ Host
To enter IP Address of theDMZ host.
IP Address
3.7.3 Network Configuration—[8-3] NAT—DMZ
Programming Item List 77
3.8 Network Configuration—[10] Port StatusDescriptionThis menu displays the link status for each port.
Screen / Tab Setting item Description Input Type Note
1.Port Status Physical LinkStatus - WAN1
Displays the WAN Port 1physical link status, up ordown.
-
Physical LinkStatus - WAN2
Displays the WAN Port 2physical link status, up ordown.
-
Physical LinkStatus - Wireless
Displays the wirelessphysical link status, up ordown.
-
Physical LinkStatus - LAN1
Displays the LAN port 1physical link status, up ordown.
-
Physical LinkStatus - LAN2
Displays the LAN port 2physical link status, up ordown.
-
3.8 Network Configuration—[10] Port Status
78 Programming Item List
Section 4Maintenance
This section provides setting items for programmingmaintenance.
Programming Item List 79
4.1 MaintenanceDescriptionIndicates various version informations and system informations.
Screen / Tab Setting item Description Input Type Note
Maintenance—VersionInformation
Main Unit Version Indicates a main unitsoftware version ofKX-HTS series.
-
Bootloader Version Indicates a bootloaderversion of KX-HTS series.
-
Router Version Indicates KX-HTS seriesbuilt-in router version.
-
WAVE300 Version Indicates WAVE300version supported byKX-HTS series.
-
Maintenance—SystemInformation
MPR-ID Indicates an MPR-ID ofKX-HTS series.
-
Main Unit Region Indicates a region ofKX-HTS series.
-
System Up Time Indicates an accumulatedtime since KX-HTS serieshas been started.
-
4.1 Maintenance
80 Programming Item List
4.2 Maintenance—[1] ManagementDescriptionOpens or closes the port for the NW external (WAN) connection through Web Maintenance ConsoleImplement a registration for login level and a user account.
Sets acceptance or non-acceptance for remoteaccess
Radio Login level able to doRemote access is the"Installer" level.
Web MaintenancePassword for LocalAccess
Click "Edit" and displaysthe Web MaintenancePassword for the LocalAccess dialog box.
-
Web MaintenancePassword forRemote Access
Click "Edit" and displaysthe Web MaintenancePassword for the RemoteAccess dialog box.
-
System PIN forManager
Click "Edit" and displaysthe System PIN for theManager dialog box.
-
Web Auto LogoutDuration
No operation timeout(minutes)
UnsignedNumber
4.2 Maintenance—[1] Management
Programming Item List 81
4.3 Maintenance—[2] System ControlDescriptionThis section serves as reference operating instructions for the System Control menu of the Maintenancescreen when programming using Web Maintenance Console.
4.3.1 Maintenance—[2-1] System Control—Firmware Transfer toPBX
Screen / Tab Setting item Description Input Type Note
1.FirmwareTransfer toPBX
Transfer from In Location of programfiles, specify the locationof the system data fromthe Radio button.
Radio
Transfer fromLocal PC-FileName
Click Browse and specifythe location of the updatedprogram files stored onthe PC logged in to WebMaintenance Console.
-
Transfer from USBMemory-FileName
If a USB memory device isinserted into the PBX, thecontents of the followingdirectory on the device willbe checked for updatedfiles.
Select
4.3 Maintenance—[2] System Control
82 Programming Item List
4.3.2 Maintenance—[2-2] System Control—Firmware UpdateScreen / Tab Setting item Description Input Type Note
Check the target to updatefirmware file, and click"Execute".
Check
Update Target-Type
Indicates the type ofupdate firmware file.
-
Update Target-Port
Indicates a Port numberSpecifies the HDVfirmware update portnumber.
-
Update Target-Current Version
Indicates a Currentfirmware version.
-
4.3.3 Maintenance—[2-3] System Control—System Data Backup& Restore
Screen / Tab Setting item Description Input Type Note
3.SystemData Backup& Restore-System DataBackup
Backup to Select the device tobackup destination.
Radio
3.SystemData Backup& Restore-System DataRestore
Restore from Transfer source of a file tobe used to restore.
Radio
Restore from LocalPC-File Name
Indicates the filename torestore from a Local PC.Click "Browse" and selectthe restore file, and click"Execute".
-
Restore from USBMemory-FileName
Select the filename torestore from a USB, andclick "Execute".
Select
4.3.2 Maintenance—[2-2] System Control—Firmware Update
Programming Item List 83
4.3.4 Maintenance—[2-4] System Control—System ResetScreen / Tab Setting item Description Input Type Note
4.SystemReset
System Reset Reset buttonWhen programmingchanges or other changesto PBX settings require asystem reset, thiscommand allows a resetto be performed remotelyfrom Web MaintenanceConsole. When thesystem is reset, anysettings not saved to theSystem Memory are lost.A backup should beperformed before the resetto ensure no data is lost.However, a backup shouldnot be performed ifsettings or data haverecently been importedinto the system, becauseperforming a backupwould overwrite theimported data with thecurrent PBX settings.
-
4.4 Maintenance—[3] UtilityDescriptionThis section serves as reference for operating instructions for the Utility menu on the Maintenance screen ofWeb Maintenance Console.
For Filtering Setting,select the check boxes tospecify whether to receivee-mails when there is aMajor alarm, a Minoralarm, or both.
Check
System Alarm-Filtering Setting-Minor
Same as above Check
System Alarm-Email Address 1
Specify one or two e-mailaddresses that will receivesystem alarm alertmessages.
Text Email
System Alarm-Email Address 2
Same as above Text Email
System Alarm-Subject
In Subject enter the textthat will be used for thesubject header of e-mailsthat are sent.
Text5
Voice Mail-Subject
Voice mail subject Text5
Send Test Email-Email Address
Send a test e-mail toconfirm that e-mailsending settings arecorrectly configured.
Text Email
Send Test Email-Subject
In Subject, enter text to beused as the subject line ofthe e-mail sent.
Text5
3.EmailNotification-SMTP
Mail SenderInformation Name
Specifies the name to beused as the sender of thee-mails from the PBX.
Text5
Mail Address Specifies the sending e-mail address formessages sent from thePBX. This address, forexample, could be set asthe e-mail address of anadministrator.
Text Email
SMTP Server forRelay-SMTPServer Address
SMTP Server Address Radio
SMTP Server forRelay-IP Address
Specifies the IP addressof the SMTP server to beused to send e-mails.
Copyright:This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced forinternal use only. All other reproduction, in whole or in part, is prohibited without the written consent ofPanasonic System Networks Co., Ltd.