www.schunk.com 14 Technical data Moment load KLM 300 Linear modules · Pneumatic · Stroke module Designation KLM 300-H050 KLM 300-H100 KLM 300-H150 KLM 300-H200 KLM 300-H250 KLM 300-H300 ID 0314550 0314554 0314558 0314562 031 4566 03 14570 Stroke length [mm] 50 100 150 200 250 300 Extend force [FV] at 6 bar [N] 753 753 753 753 753 7 53 Retract force [FR] at 6 bar [N] 633 633 633 633 633 633 Piston diameter [mm] 40 40 40 40 40 40 Rod diameter [mm] 1 6 16 16 16 16 16 Overall length [mm] 324 32 4 52 4 52 4 724 724 Mass [kg] 6.9 6.8 9.8 9.7 12.7 12.6 Fluid consumption/1 0 mm stroke [cm³] 12.57 12.57 12.57 12.57 12.57 12.57 Minimum pressure [bar] 3 3 3 3 3 3 Maximum pressure [bar] 8 8 8 8 8 8 Nominal operating pressure [bar] 6 6 6 6 6 6 IP rating 40 40 40 40 40 40 Min. ambient temperature [°C] 5 5 5 5 5 5 Max. ambient temperature [°C] 60 60 60 60 60 60 Repeat accuracy [mm] ± 0.015 ± 0.015 ± 0.015 ± 0.01 5 ± 0.01 5 ± 0.01 5 OPTIONS and their characteristics Dust-protection version ID 0314552 0314556 031 4560 03 14564 0314568 031 4572 Designation KLM 300-H050- SD KLM 30 0-H100- S D K L M 30 0- H150 - SD KLM 300-H200-SD KLM 300-H250-SD KLM 300-H300-SD IP rating 64 64 64 64 64 64 Rod lock ID 031 4551 0314555 0314559 0314563 031456 7 031 4571 Designation KLM 300-H050-A SP KLM 3 00 -H100-A SP KL M 3 00 - H150-A S P KLM 300-H200-ASP KLM 300-250-ASP KLM 300-H300-ASP Stroke loss of nominal stroke (on the rod side) [mm] 22 22 22 22 22 22 Mayy [kg] 7.4 7.3 10.3 1 0.2 13.2 1 3.1 Static holding force [N] 1000 1000 1000 1 000 1 000 1 000 max. axial backlash of the clamping [mm] 0.25 0.25 0.25 0.25 0.25 0.25 ZZA intermediate stop on the rod side possible Yes Y es Y es Y es Y es Yes ZZA intermediate stop side on the piston possible Yes Y es Y es Y es Y es Yes LMZAW intermedite stop possible No No No No No No Designation F y /F z M x M y M z [N] [Nm] [Nm] [Nm] KLM 300-H050 3120 90 200 200 KLM 300-H100 3120 90 200 200 KLM 300-H150 2490 72 350 350 KLM 300-H200 2490 72 350 350 KLM 300-H250 1870 54 415 415 KLM 300-H300 1870 54 415 415 L = 61 mm The forces and moments shown here are maximum values for individual loading. If more than one force or moment occurs simultaneously, the application can be calculated by the TOOLBOX sizing software.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
8/12/2019 KLM_300_EN
http://slidepdf.com/reader/full/klm300en 1/4w w w . s c h u n k . c o m14
Technical data
Moment load
KLM 300Linear modules · Pneumatic · Stroke module
Designation KLM 300-H050 KLM 300-H100 KLM 300-H150 KLM 300-H200 KLM 300-H250 KLM 300-H300
ID 0314550 0314554 0314558 0314562 0314566 0314570
Stroke length [mm] 50 100 150 200 250 300
Extend force [FV] at 6 bar [N] 753 753 753 753 753 753
Retract force [FR] at 6 bar [N] 633 633 633 633 633 633Piston diameter [mm] 40 40 40 40 40 40
Rod diameter [mm] 16 16 16 16 16 16
Overall length [mm] 324 324 524 524 724 724Mass [kg] 6.9 6.8 9.8 9.7 12.7 12.6
Fluid consumption/10 mm stroke [cm³] 12.57 12.57 12.57 12.57 12.57 12.57
Minimum pressure [bar] 3 3 3 3 3 3Maximum pressure [bar] 8 8 8 8 8 8
Nominal operating pressure [bar] 6 6 6 6 6 6
IP rating 40 40 40 40 40 40Min. ambient temperature [°C] 5 5 5 5 5 5
Max. ambient temperature [°C] 60 60 60 60 60 60
Repeat accuracy [mm] ± 0.015 ± 0.015 ± 0.015 ± 0.015 ± 0.015 ± 0.015OPTIONS and their characteristics
Dust-protection version ID 0314552 0314556 0314560 0314564 0314568 0314572
Designation KLM 300-H050-SD KLM 300-H100-SD KLM 300-H150-SD KLM 300-H200-SD KLM 300-H250-SD KLM 300-H300-SD
IP rating 64 64 64 64 64 64
Rod lock ID 0314551 0314555 0314559 0314563 0314567 0314571
Designation KLM 300-H050-ASP KLM 300-H100-ASP KLM 300-H150-ASP KLM 300-H200-ASP KLM 300-250-ASP KLM 300-H300-ASP
Stroke loss of nominal stroke (on the rod side) [mm] 22 22 22 22 22 22
Mayy [kg] 7.4 7.3 10.3 10.2 13.2 13.1
Static holding force [N] 1000 1000 1000 1000 1000 1000
max. axial backlash of the clamping [mm] 0.25 0.25 0.25 0.25 0.25 0.25ZZA intermediate stop on the rod side possible Yes Yes Yes Yes Yes Yes
ZZA intermediate stop side on the piston possible Yes Yes Yes Yes Yes Yes
LMZAW intermedite stop possible No No No No No No
Designation Fy /Fz Mx My Mz
[N] [Nm] [Nm] [Nm]
KLM 300-H050 3120 90 200 200KLM 300-H100 3120 90 200 200
KLM 300-H150 2490 72 350 350
KLM 300-H200 2490 72 350 350
KLM 300-H250 1870 54 415 415KLM 300-H300 1870 54 415 415
L = 61 mm
The forces and moments shown here are maximum valuesfor individual loading. If more than one force or moment
occurs simultaneously, the application can be calculated bythe TOOLBOX sizing software.
8/12/2019 KLM_300_EN
http://slidepdf.com/reader/full/klm300en 2/4 V e r k a u f k + 4 9 - 7 1 3 3 - 1 0 3 - 2 5 0 3 · T e c h n i k k + 4 9 - 7 1 3 3 - 1 0 3 - 2 6 9 6 15
KLM 300Linear modules · Pneumatic · Stroke module
You can find further information and components for the accessories mentioned here in the “Accessories” part of the catalog.
Main views, KLM 300-H100
Stroke variants
A, a Main and direct connections, extend linear unit
B, b Main and direct connections, retract linear unit1 Connection, linear unit2 Connection of the assembly On both attachment faces Back Through-bores in the face plate and thread in the base body (only single sided) Sensors and shock absorbers can also be fastened to the back. For variant H025, the sensors, shock
absorbers, and the air connections have to be fastened crosswise.
Type Stroke A B C D E G[mm] [mm] [mm] [mm] [mm] [mm] [mm]
KLM 300-H050 50 324 1x50 4x25 27…77 170 127…77KLM 300-H100 100 324 1x50 4x25 27…127 170 127…27
KLM 300-H150 150 524 3x50 8x25 27…177 270 227…77
KLM 300-H200 200 524 3x50 8x25 27…227 270 227…27KLM 300-H250 250 724 5x50 12x25 27…277 370 327…77
KLM 300-H300 300 724 5x50 12x25 27…327 370 327…27
Variable dimensions of stroke variants
The linear module can be fastened either to the base body or the face plates. Thestructure can also optionally be fastened to either the face plates or the base body.This view shows the mounting of the module to the base body and the mounting ofthe structure to the face plates.
Not all dimensions shown can be seen in the main view.
8/12/2019 KLM_300_EN
http://slidepdf.com/reader/full/klm300en 3/4
8/12/2019 KLM_300_EN
http://slidepdf.com/reader/full/klm300en 4/4 V e r k a u f k + 4 9 - 7 1 3 3 - 1 0 3 - 2 5 0 3 · T e c h n i k k + 4 9 - 7 1 3 3 - 1 0 3 - 2 6 9 6 17
KLM 300Linear modules · Pneumatic · Stroke module
Inductive attachment, NHS
Intermediate stop, ZZA on the piston side Intermediate stop, ZZA on the piston rod side
Air connection Intermediate stroke Overall length “A”, the variant without intermediate stroke (see dimension table of stroke variants)
ZZA 305
Holding force at 6 bar [N] 460
Additional mass at 0 mm stroke [kg] 0.75Additional mass per mm stroke [kg] 0.006
Sample order KLM 300-H100-ZZA305-H100
The intermediate position is measured from the respective end position. Theintermediate position can be approached from both sides and can proceed in theoriginal stroke direction.. The holding force is the piston force of the intermediatestop less the piston force of the linear module.
Air connection Intermediate stroke Overall length “A”, the variant without intermediate stroke (see dimension table of stroke variants)
ZZA 306
Holding force at 6 bar [N] 460
Additional mass at 0 mm stroke [kg] 0.75Additional mass per mm stroke [kg] 0.006
Sample order KLM 300-H100-ZZA306-H100
The intermediate position is measured from the respective end position. Theintermediate position can be approached from both sides and can proceed in theoriginal stroke direction.. The holding force is the piston force of the intermediatestop less the piston force of the linear module.
End-position monitoring: Inductive proximity switch, can be directly mounted
Designation ID
NI 30-KT 0313429
Extension cable for proximity switch
Designation ID
KA-BG08-L 3P-0500-PNP 0301623
KA BW08-L 3P-0500-PNP 0301502
Generally, two sensors are needed for each linear unit. For additional monitoring of the inter-mediate positions, one sensor per additional position as well as (optionally) one extension
cable will be needed.
You can find further information and components for the accessories mentioned here in the “Accessories” part of the catalog.