This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES
A heavy duty double flanged concentric design resilient seated butterfly valve
FEATURES
• Double flanged body design with face-to-face dimensions, according to EN 558 Series 20, API 609 and AWWA C504 short.
• Designed according to EN 593 and API 609.• The seat is field replaceable and fully isolates
the body and shaft from the flow.• Primary shaft sealing exceeds the pressure
rating of the valve and prevents leakage through shaft area to atmosphere.
• A secondary shaft sealing provides back-up safety.
• A molded-in O-ring in the seat for flange sealing eliminates the need for gaskets.
• Shaft seals prevent moisture penetrating into the shaft area.
• Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life and drop-tight shut-off.
• Extended body neck allows for pipe insulation.• Top and bottom shaft bearings for optimized
support and minimum friction and decreased torque.
• Top bushing absorbs actuator side thrust loads.
• All valves comply to Pressure Equipment Directive (97/23/EU) Module B1 + D, CE Marking.
• Available approvals: ABS, NSF/ANSI STD 61.
GENERAL APPLICATION
These valves are for water or air service where a drop-tight shut-off and double flanged body are required.
TECHNICAL DATA
Sizes: DN 600-1800 (NPS 24-72)Pressure: 10 bar DN 600-1800
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES
NOTES1. ‘Q’ dimension is the minimum allowable pipe or flange inside diameter at the centered body face to protect the disc sealing edge against damage when opening the valve.2. Weight may vary depending on trim materials used.3. See installation, operation and maintenance manual (IOM) for detailed bolting information.
DN 600-1000(NPS 24-40)
4 blind holes threaded
VALVE DIMENSIONS (mm)
Size (DN)
Shaft Top plate drilling Tap depth
UAdapt. code
Weight(2) (kg)
Bolt circle
No. holes
Holes dia.A B C D E F J L M N Q(1) T YY G Key α
VALVE DIMENSIONS (inches)
Size (NPS)
Shaft Top plate drilling Tap depth
UAdapt. code
Weight(2)
(lbs)Bolt
circleNo.
holesHoles
dia.A B C D E F J L M N Q(1) T YY G Key α
5
All information hereon is of a proprietary nature confidential and the prop erty of Pen tair Valves & Controls B.V. loaned to others for expressed purposes onl y and sh all not be reprodu ced or disclosed wi thout written consen t of the comp any.
KEYSTONE
CF
ØG
J
L P
Q YY B
D
A M
R
a
PC
D
ØE
ØND
T
DN NPS D A M Q YY B T C J G R F TopplateSize E P N L PCD Hole dia No α Weight Key width Key height Key lengthmm in mm mm mm mm mm mm mm mm mm mm mm mm ISO521 1 mm mm mm mm mm mm ° kg mm mm mm
All information hereon is of a proprietary nature confidential and the prop erty of Pen tair Valves & Controls B.V. loaned to others for expressed purposes onl y and sh all not be reprodu ced or disclosed wi thout written consen t of the comp any.
KEYSTONE
CF
ØG
J
L P
Q YY B
D
A M
R
a
PC
D
ØE
ØND
T
DN NPS D A M Q YY B T C J G R F TopplateSize E P N L PCD Hole dia No α Weight Key width Key height Key lengthmm in mm mm mm mm mm mm mm mm mm mm mm mm ISO521 1 mm mm mm mm mm mm ° kg mm mm mm
All information hereon is of a proprietary nature confidential and the prop erty of Pen tair Valves & Controls B.V. loaned to others for expressed purposes onl y and sh all not be reprodu ced or disclosed wi thout written consen t of the comp any.
KEYSTONE
CF
ØG
J
L P
Q YY B
D
A M
R
a
PC
D
ØE
ØND
T
DN NPS D A M Q YY B T C J G R F TopplateSize E P N L PCD Hole dia No α Weight Key width Key height Key lengthmm in mm mm mm mm mm mm mm mm mm mm mm mm ISO521 1 mm mm mm mm mm mm ° kg mm mm mm
All information hereon is of a proprietary nature confidential and the prop erty of Pen tair Valves & Controls B.V. loaned to others for expressed purposes onl y and sh all not be reprodu ced or disclosed wi thout written consen t of the comp any.
KEYSTONE
CF
ØG
J
L P
Q YY B
D
A M
R
a
PC
D
ØE
ØND
T
DN NPS D A M Q YY B T C J G R F TopplateSize E P N L PCD Hole dia No α Weight Key width Key height Key lengthmm in mm mm mm mm mm mm mm mm mm mm mm mm ISO521 1 mm mm mm mm mm mm ° kg mm mm mm
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES
DN 1050-1800(NPS 42-72)
VALVE DIMENSIONS (mm)
Size (DN)
Shaft Top plate drilling Tap depth
UAdapt. code
Weight(2)
(kg)Key
lengthBolt
circleNo.
holesHoles
dia.A B C D E F J L M N P Q(1) R T YY G Key α
NOTES1. ‘Q’ dimension is the minimum allowable pipe or flange inside diameter at the centered body face to protect the disc sealing edge against damage when opening the valve.2. Weight may vary depending on trim materials used.3. See installation, operation and maintenance manual (IOM) for detailed bolting information.
Application IClean liquid lubricating media (water, clean oils, lube oil, mineral oil, etc.); and with no deposit or chemical attack, valve operated at least once a week.Temperature range from 0°C (32°F) to maximum temperature rating of the elastomer seat.
Application IIOther liquid media and lubricating gases (aqueous liquids, such as food and beverage, water, etc.); and with minor deposit or chemical attack, valve operated at least once a month.Temperature range from 0°C (-14°F) to maximum temperature rating of the elastomer seat.
Application IIIa. Dry non-abrasive media or gases (non-abrasive powders and dry gas); orb. Fluids with moderate deposit or chemical attack; orc. Valves operated less than once a month.Temperature range from 0°C (32°F) to maximum temperature rating of the elastomer seat.
Application IVa. Dry abrasive media and degreasing applications (sand, cement, silicone free, oxygen cleaned); orb. Liquids with severe deposit; orc. Valves not frequently operated (once a year).All above with temperature range from -10°C (-14°F) to maximum temperature rating of the elastomer seat.
NOTES1. For applications with temperatures above or below the guidelines above, please consult factory.2. For dry service valves it is suggested to use U/C discs (reduced diameter) when service conditions are less than 3.5 bar (50 psi).
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVESMETRIC TABLES
NOTES3.5 U/C refers to reduced diameter disc option.1. Use a minimum of Class 8.8 steel bolts to connect actuator to valve.2. Duplex shaft not suitable for these conditions, use only 431 stainless steel or super duplex.
NOTES50 U/C refers to reduced diameter disc option.1. Use a minimum of ASTM A193 Grade B7 steel bolts to connect actuator to valve.2. Duplex shaft not suitable for these conditions, use only 431 stainless steel or super duplex.
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVESIMPERIAL TABLES
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVESMETRIC TABLES
FLOWRATE CO-EFFICIENTS - Kv VALUES
Size (DN)Disc opening (degrees)
10° 20° 30° 40° 50° 60° 70° 80° 90°
NOTEKv = The volume of water in m3/hr that will pass through a valve with a pressure drop of 1 bar at 20°C
POSSIBLE FLANGE DRILLINGS
Flange drillingValve size (DN)
600 700 750 800 900 1000 1050 1100 1200 1350 1400 1500 1600 1650 1800EN 1092 PN 10 N/A N/A N/A N/A N/AISO 2084 PN 10 N/A N/A N/AASME B16.5 Class 150 See B16.47A N/AASME B16.1 Class 125 N/A N/A N/A N/A N/A N/AASME B16.47A Class 150 See B16.5 N/AAWWA C207 Table B/D/E N/A N/AMSS SP44 Class 150 N/AASME B16.47B Class 150 N/A O O N/A O O O O O N/AJIS B2210 10K N/A N/A N/AJIS B2210 5K O O O O N/A O O O N/A O N/AAS2129 Table D N/A N/A N/A N/AAS4087 PN 16 N/A N/A N/A N/AAS2129 Table E N/A N/A
** Standard / End of line
NOTES Standard possible for all versions Optional, contact factory Not applicable
EPDM All metalDI A536 65-45-12/ CS A216 WCB/ SS A351 CF8M
600-1800 Std / EOL 10 bar / 6 bar
EPDM All metal DI A395 60-40-18 600-1800 Std / EOL 10 bar / 6 bar
NBR/NBR white All metalDI A536 65-45-12/ CS A216 WCB/ SS A351 CF8M
600-1800 Std / EOL 10 bar / 6 bar
FKM All metalDI A536 65-45-12/ CS A216 WCB/ SS A351 CF8M
600-1000 Std / EOL 10 bar / 6 bar 6 bar / 4 bar
TEMPERATURE PERFORMANCE COATED DISCDisc material Coating Size range (DN) °CDI A536 65-45-12 / A395 60-40-18 DI epoxy coated 600-1800 -28 to 120 / -40 to 120DI A536 65-45-12 / A395 60-40-18 DI nylon coated 600-1800 -28 to 60 / -40 to 60DI A536 65-45-12 / A395 60-40-18 DI FBE coated 600-1800 -28 to 52 / -40 to 52DI A536 65-45-12 / A395 60-40-18 DI ebonite coated 600-1800 -28 to 100 / -40 to 100
Data is valid for flat face flanges. For raised face, please consult factory.DN 1600 is not available with ASME drilling. See above chart for drilling details.See installation, operations and maintenance manual (IOM) for detailed bolting information.
NOTECv = The volume of water in U.S.gpm that will pass through a valve with a pressure drop of 1 psi at 60°F
FLOWRATE CO-EFFICIENTS - Cv VALUES
Size (NPS)Disc opening (degrees)
10° 20° 30° 40° 50° 60° 70° 80° 90°
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVESIMPERIAL TABLES
** Standard / End of line
POSSIBLE FLANGE DRILLINGS
Flange drillingValve size (NPS)
24 28 30 32 36 40 42 44 48 54 56 60 64 66 72EN 1092 PN 10 N/A N/A N/A N/A N/AISO 2084 PN 10 N/A N/A N/AASME B16.5 Class 150 See B16.47A N/AASME B16.1 Class 125 N/A N/A N/A N/A N/A N/AASME B16.47A Class 150 See B16.5 N/AAWWA C207 Table B/D/E N/A N/AMSS SP44 Class 150 N/AASME B16.47B Class 150 N/A O O N/A O O O O O N/AJIS B2210 10K N/A N/A N/AJIS B2210 5K O O O O N/A O O O N/A O N/AAS2129 Table D N/A N/A N/A N/AAS4087 PN 16 N/A N/A N/A N/AAS2129 Table E N/A N/A
EPDM All metalDI A536 65-45-12/ CS A216 WCB/ SS A351 CF8M
24-72 Std / EOL 150 psi / 90 psi
EPDM All metal DI A395 60-40-18 24-72 Std / EOL 150 psi / 90 psiNBR/NBR white
All metalDI A536 65-45-12/ A395 60-40-18/ CS A216 WCB/ SS A351 CF8M
24-72 Std / EOL 150 psi / 90 psi
FKM All metalDI A536 65-45-12/ A395 60-40-18/ CS A216 WCB/ SS A351 CF8M
24-40 Std / EOL 150 psi / 90 psi90 psi / 60
psi
TEMPERATURE PERFORMANCE COATED DISCDisc material Coating Size range (NPS) °FDI A536 65-45-12 / A395 60-40-18 DI epoxy coated 24-72 -20 to 250 / -40 to 250DI A536 65-45-12 / A395 60-40-18 DI nylon coated 24-72 -20 to 140 / -40 to 140DI A536 65-45-12 / A395 60-40-18 DI FBE coated 24-72 -20 to 125 / -40 to 125DI A536 65-45-12 / A395 60-40-18 DI ebonite coated 24-72 -20 to 212 / -40 to 212
NOTES Standard possible for all versions Optional, contact factory Not applicable
ON/A
Data is valid for flat face flanges. For raised face, please consult factory.NPS 64 is not available with ASME drilling. See above chart for drilling details.See installation, operations and maintenance manual (IOM) for detailed bolting information.
10
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES
NOTES1. Fluoroelastomer (FKM) available in size up to DN 1000 (NPS 40) only.2. Valves in size DN 600-900 (NPS 24-36) are Keystone topplate mounting. Valves in size DN 1000-1800 (NPS 40-72) are ISO 5211 topplate mounting.3. FBE = Fusion bond epoxy
Other options are available on request. Please contact your local sales representative.Monel® is a registered trademark of the Special Metals Corporation.
K Keysone mountI ISO mount (above NPS 40)Actuation00 NoneG1 Gear - blueG5 Chainwheel - blueSpecial000 NoneP04 Reduced disc for 50 psi027 Vacuum holes and fittingsCoating00 Standard blue02 C3 Keystone blue03 C5M Keystone blue04 FBE coated body - blue
11
KEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES
12
Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
FCT is a mark owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.