Keypad / Display Rev. J -12/12/2015.

Keypad / Displaywww.mcscontrols.com

Rev. J -04/21/23

Keypad/DisplayKeypad/Display

Keypad/DisplayKeypad/Display

Graphics Display

Function Keys

Direction Movement Keys

Menu Key, Enter Key & RS232 Communications

Port

Menu KeyMenu Key

Press Menu Key

Main MenuMain Menu

Press ‘F1’For ‘Help’

Help ScreenHelp Screen

Press Menu Key

Main MenuMain Menu

Press ‘F3’For Large

Large FontLarge Font

Press Menu Key

Main MenuMain Menu

Press ‘‘

Status Status (Unit - Wanted / Actual)(Unit - Wanted / Actual)

Press ‘F3’ for Page Down

Status Status (Unit - Kw/Tons)(Unit - Kw/Tons)


Status Status (CMP1 - Pressures/AMPS)(CMP1 - Pressures/AMPS)

Press ‘’



Status Status (CMP1 - Superheats)(CMP1 - Superheats)

Press ‘’


Press ‘’



StatusStatus(EXV 1)(EXV 1)



Press ‘’




Press ‘’


Press ‘’



Status Status (EXV 2)(EXV 2)

Press ‘F3’ for Page DownTo Loop The

Menu

Status Status (Unit - Wanted / Actual)(Unit - Wanted / Actual)

Press Menu Key

Main MenuMain Menu

Press ‘'

Main MenuMain Menu

Press ‘‘

OutputsOutputs(Relay M-1 - Status)(Relay M-1 - Status)

Press ‘’

OutputsOutputs(Relay M-1 - Last On)(Relay M-1 - Last On)

Press ‘’

OutputsOutputs(Relay M-1 - Last Off)(Relay M-1 - Last Off)

Press ‘’

OutputsOutputs(Relay M-1 - Run Today)(Relay M-1 - Run Today)

Press ‘’

OutputsOutputs(Relay M-1 - Cycles Today)(Relay M-1 - Cycles Today)

Press ‘’

OutputsOutputs(Relay M-1 - Run Yesterday)(Relay M-1 - Run Yesterday)

Press ‘’

OutputsOutputs(Relay M-1 - Cycles Yesterday)(Relay M-1 - Cycles Yesterday)

Press ‘’

OutputsOutputs(Relay M-1 - Total Run Hours)(Relay M-1 - Total Run Hours)

Press ‘’

OutputsOutputs(Relay M-1 - Total Cycles)(Relay M-1 - Total Cycles)

Press ‘’


Press ‘‘




Press ‘‘

OutputsOutputs(Relay M-5 - Status - Change [Auto])(Relay M-5 - Status - Change [Auto])

Press ‘‘

OutputsOutputs(Relay M-5 - Status - Change [ManOff])(Relay M-5 - Status - Change [ManOff])

Press ‘‘

OutputsOutputs(Relay M-5 - Status - Change [ManOn])(Relay M-5 - Status - Change [ManOn])

Press ‘‘

OutputsOutputs(Relay M-5 - [Change Made or Failed])(Relay M-5 - [Change Made or Failed])

Press ‘‘


Press ‘F1’ for Analog

OutputsOutputs(Analog M-1 - Status)(Analog M-1 - Status)

Press ‘‘

OutputsOutputs(Analog M-1 - Status - Change [Auto])(Analog M-1 - Status - Change [Auto])

Press ‘’

OutputsOutputs(Analog M-1 - Status - Change [Man])(Analog M-1 - Status - Change [Man])

Press ‘’


Press ‘’


Press ‘‘

OutputsOutputs(Analog M-1 - [Change Made or (Analog M-1 - [Change Made or

Failed])Failed])

Press ‘‘


Press ‘‘



OutputsOutputs(Analog 1-1 - Status)(Analog 1-1 - Status)

Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

InputsInputs(Sensor M-1 - Value)(Sensor M-1 - Value)

Press ‘’

InputsInputs(Sensor M-1 - Type)(Sensor M-1 - Type)

Press ‘’

InputsInputs(Sensor M-1 - Last On)(Sensor M-1 - Last On)

Press ‘’

InputsInputs(Sensor M-1 - Last Off)(Sensor M-1 - Last Off)

Press ‘’

InputsInputs(Sensor M-1 - Max Today)(Sensor M-1 - Max Today)

Press ‘’

InputsInputs(Sensor M-1 - Min Today)(Sensor M-1 - Min Today)

Press ‘’

InputsInputs(Sensor M-1 - Run Today)(Sensor M-1 - Run Today)

Press ‘’

InputsInputs(Sensor M-1 - Average Today)(Sensor M-1 - Average Today)

Press ‘’

InputsInputs(Sensor M-1 - Cycles Today)(Sensor M-1 - Cycles Today)

Press ‘’

InputsInputs(Sensor M-1 - Run Yesterday)(Sensor M-1 - Run Yesterday)

Press ‘’

InputsInputs(Sensor M-1 - Max Yesterday)(Sensor M-1 - Max Yesterday)

Press ‘’

InputsInputs(Sensor M-1 - Cycles Yesterday)(Sensor M-1 - Cycles Yesterday)

Press ‘’

InputsInputs(Sensor M-1 - Min Yesterday)(Sensor M-1 - Min Yesterday)

Press ‘’

InputsInputs(Sensor M-1 - Total Run Hours)(Sensor M-1 - Total Run Hours)

Press ‘’

InputsInputs(Sensor M-1 - Average Yesterday)(Sensor M-1 - Average Yesterday)

Press ‘’

InputsInputs(Sensor M-1 - Total Cycles)(Sensor M-1 - Total Cycles)

Press ‘’


Press ‘‘

InputsInputs(Sensor M-1 - Value Change [Auto])(Sensor M-1 - Value Change [Auto])

Press ‘‘

InputsInputs(Sensor M-1 - Type Change [MCST100])(Sensor M-1 - Type Change [MCST100])

Press ‘‘

InputsInputs(Sensor M-1 - Change [Exit])(Sensor M-1 - Change [Exit])

Press ‘‘


Press ‘‘




Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

AlarmsAlarms(1 & 2)(1 & 2)


AlarmsAlarms(3 & 4)(3 & 4)

Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

GraphsGraphs(SI- Chill Water In)(SI- Chill Water In)

Press ‘F3’ for Analog Outputs

GraphsGraphs(AO - EXV1)(AO - EXV1)

Press ‘F3’ for Relay Outputs

\\

GraphsGraphs(RO - Compressor 1)(RO - Compressor 1)

Press ‘F2’ for Sensor Inputs

GraphsGraphs(SI - Chill Water In)(SI - Chill Water In)

Press ‘F1’ for Edit

GraphsGraphs(SI - Change Sample Rate)(SI - Change Sample Rate)

Press ‘’

GraphsGraphs(SI - Change Sample Rate)(SI - Change Sample Rate)

Press ‘‘

GraphsGraphs(SI - Change Made or Failed)(SI - Change Made or Failed)

Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

Set pointsSet points(1 - Value)(1 - Value)

Press ‘’

Set pointsSet points(1 - Time)(1 - Time)

Press ‘’

Set pointsSet points(1 - Column A)(1 - Column A)

Press ‘’

Set pointsSet points(1 - Column B)(1 - Column B)

Press ‘’

Set pointsSet points(1 - Column C)(1 - Column C)

Press ‘’


Press ‘‘


Press ‘‘


Press ‘‘


Press ‘‘


Press ‘‘


Press ‘‘

Set pointsSet points(Set point 1 - Value)(Set point 1 - Value)

Press ‘‘

Set pointsSet points(Set point 1 - Set Value - 45.0 F)(Set point 1 - Set Value - 45.0 F)

Press ‘’

Set pointsSet points(Set point 1 - Set Value - 45.5 F)(Set point 1 - Set Value - 45.5 F)

Press ‘‘

Set pointsSet points(Set point 1 - [Change Made or Failed])(Set point 1 - [Change Made or Failed])

Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

Service ToolsService Tools(RS485 Network)(RS485 Network)

Press ‘‘

Service ToolsService Tools(RS485 Network - Protocol)(RS485 Network - Protocol)

Press ‘F1’ for Back


Press ‘‘

Service ToolsService Tools(Ethernet Network)(Ethernet Network)

Press ‘‘

Service ToolsService Tools(Ethernet - Dynamic IP)(Ethernet - Dynamic IP)

Press ‘‘

Service ToolsService Tools(Ethernet - IP Address)(Ethernet - IP Address)

Press ‘‘

Service ToolsService Tools(Ethernet - Subnet Mask)(Ethernet - Subnet Mask)

Press ‘‘

Service ToolsService Tools(Ethernet - Default Gateway)(Ethernet - Default Gateway)

Press ‘‘

Service ToolsService Tools(Ethernet - MCS Port)(Ethernet - MCS Port)

Press ‘‘

Service ToolsService Tools(Ethernet - Dynamic IP)(Ethernet - Dynamic IP)



Press ‘‘


Press ‘‘

Service ToolsService Tools(System Info)(System Info)

Press ‘‘

Service ToolsService Tools(System Info - Firmware Version)(System Info - Firmware Version)

Press ‘F3’ for PG

Service ToolsService Tools(System Info - Company Name)(System Info - Company Name)


Service ToolsService Tools(System Info - Unit Serial Number)(System Info - Unit Serial Number)


Service ToolsService Tools(System Info - Config Version(System Info - Config Version))


Service ToolsService Tools(System Info - Bootloader Version)(System Info - Bootloader Version)


Service ToolsService Tools(System Info - Physical Mac Address)(System Info - Physical Mac Address)



Press ‘‘


Press ‘‘


Press ‘‘

Service ToolsService Tools(Time / Date)(Time / Date)

Press ‘‘

Service ToolsService Tools(Time / Date - Hours)(Time / Date - Hours)

Press ‘‘

Service ToolsService Tools(Time / Date - Minute)(Time / Date - Minute)

Press ‘‘

Service ToolsService Tools(Time / Date - Second)(Time / Date - Second)

Press ‘‘

Service ToolsService Tools(Time / Date - Save Changes)(Time / Date - Save Changes)

Press ‘‘

Note: No authorization is required for a time change


Press ‘‘


Press ‘‘


Press ‘‘

Service ToolsService Tools(Time / Date)(Time / Date)

Press ‘‘

Service ToolsService Tools(Display)(Display)

Press ‘‘

Service ToolsService Tools(Display - Contrast)(Display - Contrast)




Service ToolsService Tools(Clear Alarm History)(Clear Alarm History)

Press ‘‘

Service ToolsService Tools(Clear Alarm History - Yes)(Clear Alarm History - Yes)

Press ‘‘

Service ToolsService Tools(Clear Alarm History - No)(Clear Alarm History - No)

Press ‘‘


Press ‘‘

Service ToolsService Tools(Clear Point Info)(Clear Point Info)

Press ‘‘

Service ToolsService Tools(Clear Point Info - Yes)(Clear Point Info - Yes)

Press ‘‘

Service ToolsService Tools(Change Made / Higher Auth Required)(Change Made / Higher Auth Required)

Press ‘‘


Press ‘‘

Service ToolsService Tools(Sensor Diagnostics)(Sensor Diagnostics)

Press ‘‘

Revision H - 4/30/2014

Service ToolsService Tools(Sensor Diagnostics - M-1)(Sensor Diagnostics - M-1)





Press ‘‘


Press ‘‘


Press ‘‘

Service ToolsService Tools(Config Checksums)(Config Checksums)

Press ‘‘

Service ToolsService Tools(Config Checksums - # 0)(Config Checksums - # 0)





Press ‘‘


Press ‘‘


Press ‘‘

Service ToolsService Tools(Config Checksums)(Config Checksums)

Press ‘‘

Service ToolsService Tools(Operating Schedule)(Operating Schedule)

Press ‘‘

Service ToolsService Tools(Operating Schedule - Sunday)(Operating Schedule - Sunday)






Service ToolsService Tools(Holiday Dates)(Holiday Dates)

Press ‘‘

Service ToolsService Tools(Holiday Dates - # 1)(Holiday Dates - # 1)

Press ‘‘

Service ToolsService Tools(Holiday Dates - # 1 - Month[ ])(Holiday Dates - # 1 - Month[ ])

Press ‘‘

Service ToolsService Tools(Holiday Dates - # 1 - Month[ Jan ])(Holiday Dates - # 1 - Month[ Jan ])

Press ‘‘

Service ToolsService Tools(Holiday Dates - Change Made / Higher Auth (Holiday Dates - Change Made / Higher Auth

Required)Required)

Press ‘‘

Service ToolsService Tools(Holiday Dates - # 1)(Holiday Dates - # 1)



Press ‘‘

Service ToolsService Tools(BACnet Settings)(BACnet Settings)

Press ‘‘

Service ToolsService Tools(BACnet Settings - Device ID)(BACnet Settings - Device ID)

Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

Lockout ResetLockout Reset(Yes / No Lockouts)(Yes / No Lockouts)

Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

Lockout AlarmLockout Alarm(Alarm 1)(Alarm 1)

Press ‘‘


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘’


Press ‘F3’ for Next


Press Menu Key

Main MenuMain Menu

Press ‘‘

Main MenuMain Menu

Press ‘‘

PasswordPassword

Press ‘F3’ for 3

PasswordPassword


PasswordPassword


PasswordPassword


PasswordPassword

Press ‘‘

Password AcceptedPassword Accepted

Press Menu Key

Main MenuMain Menu

You are automatically logged out if no key is pressed for 15 minutes

You may logoff by putting any invalid code in Password

You are limited to how many lockout resets you can do in 1 day

After the limit, a Factory Authorization is required to reset

Password & Lockout ResetPassword & Lockout Reset

Revision H - 4/30/2014

For additional information please contact MCS or visit our website

www.mcscontrols.com

Keypad / Display Rev. J -12/12/2015.

Documents

valuepress inputssensor

statuspress outputsrelay

change exitpress inputssensor

offpress inputssensor

onpress inputssensor

statuspress f3

typepress inputssensor

cycles todaypress inputssensor