KEANE - Lowe'spdf.lowes.com/installationguides/1000319197_install.pdf · KEANE™ 52” Ceiling Fan Owner's Manual Model Numbers CF320BS00 - Brushed Steel CF320SW00 - Satin White

Part No. F40BP75140000 Form No. BP7514Revision: 151218 ETL Model No.: CF320

READ AND SAVE THESE INSTRUCTIONS

KEANE™

52” Ceiling Fan Owner's ManualModel Numbers

CF320BS00 - Brushed SteelCF320SW00 - Satin White

Net Weight: 13.5 Lbs.

Questions, problems, missing parts: Before returning to the store callEmerson Electric Customer Service

8 a.m. - 6 p.m., Eastern, Monday-Friday

1-800-654-3545

www.emersonfans.com

• Español - página 23• Français - page 45

CO

NTE

MP

OR

AR

Y

4

0

3

2

1

BP7514 CF320 Keane 12 2015_CF320 1/7/16 10:42 AM Page 1

2 ETL Model No.: CF320

Table of Contents

Safety Instructions

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:a. Use this unit only in a manner intended by the

manufacturer. If you have questions, contact themanufacturer.

b. Before servicing or cleaning unit, switch power off atservice panel and lock service panel disconnectingmeans to prevent power from being switched onaccidentally. When the service disconnecting meanscannot be locked, securely fasten a warning device,such as a tag, to the service panel.

WARNING!

Additional Safety Instructions for Installation1. To avoid possible shock, be sure electricity is turned off

at the fuse box before wiring, and do not operate fanwithout blades.

2. All wiring must be in accordance with the NationalElectrical Code “ANSI/NFPA 70-2014” and LocalElectrical Codes. Use the National Electrical Code ifLocal Codes do not exist. The ceiling fan must begrounded as a precaution against possible electricalshock. Electrical installation should be made orapproved by a licensed electrician.

3. The outlet box and joist must be securely mounted andcapable of reliably supporting at least 50 pounds. Useonly U.L. outlet boxes listed as “Acceptable for FanSupport of 22.7kg. (50 lbs.) or less”, and use themounting screws provided with the outlet box. Mostoutlet boxes commonly used for support of light fixturesare not acceptable for fan support and may need to bereplaced. Consult a qualified electrician if in doubt.

4. The downrod furnished with the fan provides theminimum recommended floor to fan blade clearance foran 8 foot ceiling.

5. The fan must be mounted with the fan blades at least7 feet from the floor to prevent accidental contact withthe fan blades.

6. Follow the recommended instructions for the propermethod of wiring your ceiling fan. If you do not knowenough about electrical wiring, have your fan installed bya licensed electrician.

NOTE: This fan is suitable for use with solid-state speedcontrols.NOTE: All setscrews must be checked and re-tightenedwhere necessary before installation.

1. Read your owner’s manual carefully and keep it for futurereference.

2. Be careful of the fan and blades when cleaning, painting,or working near the fan. Always turn off the power to theceiling fan before servicing.

3. Do not put anything into the fan blades while they areturning.

4. Do not operate reversing switch until fan blades havecome to a complete stop.

READ AND SAVE THESE INSTRUCTIONS

Section PageSafety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21. Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-42. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43. Ceiling Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-84. How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .9-105.Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . .12-147. Installing the Wall Control . . . . . . . . . . . . . . . . . . . . . . . .15-168. Using Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Section Page9. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1710. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1711. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-1912. Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . .2013. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . .21Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23French . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

To reduce the risk of electrical shock, this fan must beinstalled with an isolating wall control/switch.To reduce the risk of fire or electrical shock, this fanshould only be used with fan speed control, Model No.FR-7861LMA-02, manufactured by Rhine Electric Co., Ltd.This product is designed to use only those parts suppliedwith this product and/or any accessories designatedspecifically for use this product by Emerson Electric Co.Substitution of parts or accessories not designated foruse with this product by Emerson could result inpersonal injury or property damage.To reduce the risk of personal injury, do not bend theblade flange when installing the blade flanges, balancingthe blades or cleaning the fan. Do not insert foreignobjects in between rotating fan blades.

WARNING!

BP7514 CF320 Keane 12 2015_CF320 1/7/16 12:36 PM Page 2

1. Unpacking Instructions

This product is designed to use only those parts suppliedwith this product and/or any accessories designatedspecifically for use with this product by Emerson ElectricCo. Substitution of parts or accessories not designatedfor use with this product by Emerson Electric Co. couldresult in personal injury or property damage.

WARNING!

Do not install or use fan if any part is damaged ormissing. Call Toll-Free:

1-800-654-3545

WARNING!

3

emersonfans.comPlease contact 1-800-654-3545 for further assistance

ETL Model No.: CF320

1.1Check to see that you have received the following parts:NOTE: If you are uncertain of part description, refer toexploded view illustration.

NOTE: Place the parts from the loose parts bags in asmall container to keep them from being lost.If any parts are missing, contact your local retailer orcatalog outlet for replacement before proceeding.

1.2Remove the fan assembly from the protectiveplastic bag. Place the fan assembly into the upper foampad with the top of the motor facing up.The upper foam pad serves as a holder for the fan duringthe first stages of assembly.

H

G

E

K

B

C

A

J

ID

F

0

4321

PACKAGE CONTENTS

85

4

3

2

1

11

9

7

610

Part Description QuantityA Fan Motor Assembly 1B Hanger Bracket 1C Hanger Ball/4.5” Downrod 1D Ceiling Canopy 1E Motor Coupler Cover 1F Fan Blade Flanges 3G Decorative Blade Nuts 9H Fan Blades 3I Switch Housing Adapter 1J Switch Housing Cover 1K SW46W Wall Control 1

HARDWARE CONTENTSPart Description Quantity

1 Threaded Studs, #8-32 x 1-1/4” 22 Lockwashers, External Tooth, #8 23 Knurled Knobs, #8-32 24 Clevis Pin 15 Hairpin Clip 16 Wire Connectors 57 Washer Head Screws #8-32 x 0.312” 108 Oval Head Countersunk Screws

1/4-20 x .500” Nyloc 79 Flat Head Screw #6-32 x 0.312” (Spare) 1

10 Pan Head Screws #6-32 x 0.375” 411 Blade Balance Kit 1



Before assembling your ceiling fan, refer to section onproper method of wiring your fan (page 12). If you feelyou do not have enough wiring knowledge or experience,have your fan installed by a licensed electrician.

WARNING!

This Manual Is Designed to Make it as Easy as Possible for You to Assemble,Install, Operate and Maintain Your Ceiling Fan

Tools Needed for AssemblyOne Phillips head screwdriver One stepladderOne 1/4” blade screwdriver One wire stripper

MaterialsWiring outlet box and box connectors must be of typerequired by the local code. The minimum wire would be a3-conductor (2-wire with ground) of following size:

Installed Wire Length Wire Size A.W.G.

Up to 50 ft. 14

50-100 ft. 12

Your Emerson Ceiling Fan comes supplied with a Fan WallControl. This system allows you to regulate your ceiling fanspeed.

This Emerson Ceiling Fan may be used with the followingaccessories: RFCP Receiver and SR400/ SW405 RemoteControl.

2. Electrical RequirementsYour new ceiling fan will require a grounded electricalsupply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capable ofwithstanding a load of at least 50 pounds.

To reduce the risk of fire, electric shock, or personalinjury, mount fan to outlet box marked “Acceptable forFan Support of 22.7kg. (50 lbs.) or less”, and use screwssupplied with outlet box. Most outlet boxes commonlyused for support of light fixtures are not acceptable forfan support and may need to be replaced. Consult aqualified electrician if in doubt.

WARNING!

Turning off wall switch is not sufficient. To avoid possibleelectrical shock, be sure electricity is turned off at themain fuse box before wiring. All wiring must be inaccordance with National and Local codes and the ceilingfan must be properly grounded as a precaution againstpossible electrical shock.

WARNING!

To avoid fire or shock, follow all wiring instructionscarefully.

Any electrical work not described in theseinstructions should be done or approved by a licensedelectrician.

WARNING!

If your fan is to replace an existing ceiling light fixture, turnelectricity off at the main fuse box at this time and removethe existing light fixture.

Please call Emerson technical support at1-800-654-3545 if you have any questions aboutinstallation and operation of this ceiling fan.

1. Unpacking Instructions (Continued)


5



3. Ceiling Fan Assembly

TWO 80" MOTOR LEADS (UNTWISTED)

4.5" DOWNROD

Figure 2

3.2Separate, untwist and unkink the two motor leads.

Route the two motor leads through the downrod(Figure 2).

MOTORCOUPLING

4.5"DOWNROD

LOOSENPHILLIPS HEADSET SCREWS (2)

Figure 3

3.3Loosen the two Phillips head set screws in the motorcoupler for installation of the downrod (Figure 3).

Seat the downrod in the motor coupler (Figure 3).

Rotate and align the downrod holes with all the holes in themotor coupler (Figure 3).

PHILLIPS HEAD SET SCREW (LOOSENED)

HANGER BALL

4.5" DOWNROD

PIN

GREEN GROUND WIRE

Figure 1

3.1Remove the hanger ball by loosening the Phillips head setscrew in the hanger ball until the ball falls freely down thedownrod (Figure 1).

Remove the pin from the downrod, then remove thehanger ball (Figure 1).

Retain the pin and hanger ball for reinstallation inStep 3.7.



3. Ceiling Fan Assembly (Continued)

COUPLINGCOVER

COUPLING COVERGROMMET

MOTORHOUSING

4.5" DOWNROD

Figure 5

3.5Make sure the grommet is properly installed in the couplingcover, then slide the coupling cover on the downrod until itrests on the motor housing (Figure 5).

HAIRPINCLIPCLEVISPIN

MOTORCOUPLING

HAIRPINCLIP

CLEVISPIN

RETIGHTENPHILLIPS HEADSET SCREW (2)

Figure 4

CEILINGCOVER

4.5" DOWNROD

Figure 6

3.6Place the ceiling cover over the downrod (Figure 6).

Be sure that the ceiling cover and the coupling cover areboth oriented correctly (Figure 6).

3.4Align the clevis pin holes in the downrod with the holes inthe motor coupler.

Install the clevis pin and secure with the hairpin clip(Figure 4).

The clevis pin must go through the holes in the motorcoupler. It is critical that the clevis pin in the motor coupleris properly installed and securely tightened.

Retighten the two Phillips head set screws to secure thedownrod to the motor (Figure 4).

It is critical that the clevis pin and setscrews in the motorcoupler are properly installed and securely tightened.Failure to verify that the pin and setscrews are properlyinstalled could result in the fan falling.

WARNING!


7




HANGER BALL

WHITE WIRE

BLACK WIRE

1/2-INCH

6 TO 9INCHES

Figure 8

3.8The fan comes with black and white leads that are80” long.

Measure up approximately 6 to 9-inches above top ofhanger ball/4.5” downrod assembly (Figure 8).

Cut off excess leads and strip back insulation 1/2-inch fromend of leads.

PINHANGER BALL

PHILLIPS HEADSET SCREW

4.5" DOWNROD

Figure 7

3.7Route the two motor leads through the hanger ball (Figure7).

Reinstall the hanger ball on the downrod as follows:

Position the pin through the two holes in the downrod andalign the hanger ball so the pin is captured in the groove inthe top of the hanger ball (Figure 7).

Pull the hanger ball up tight against the pin and securelyretighten the Phillips head set screw in the hanger ball(Figure 7).

A loose Phillips head set screw could create fan wobble.




REMOVE & DISCARDSHIPPING SPACERS &ATTACHMENT SCREWS (6)

PARTIALLY ASSEMBLEDCEILING FAN

Figure 9

3.9Turn the partially assembled ceiling fan upside down, placethe ceiling fan onto the two carton styrofoam pieces, inpreparation for final assembly (Figure 9).

Remove the six shipping spacers and the spacerattachment screws from the motor before installation ofblade assemblies (Figure 9).

Discard the six shipping spacers and spacer screws.

#8-32 X 0.312"WASHER HEADSCREWS

FLANGE

BLADE

DECORATIVEBLADE NUT(3 per blade/flange)

Figure 10

3.10NOTE: Intermixing blades between fans can causeexcessive wobble. Keep blades in original sets ofthree.

Place the fan blade flange on the fan blade (Figure 10).

Place the decorative blade nut onto the underside of thefan blade (Figure 10).

Tighten the #8-32 x 0.312” washer head screw to secure(supplied in parts bag) the fan blade and the decorativeblade nut (Figure 10).

Repeat this procedure for the other two fan blade flanges,decorative blade nut and fan blades.

Make sure all #8-32 x 0.312” washer head screws aretighten securely to the decorative blade nut to secure thefan blade and flange.

1/4-20 x .500" OVAL HEADCOUNTERSUNK SCREWS(2 per blade/flange assembly)

BLADE/FLANGEASSEMBLY

MOTOR HUB

Figure 11

3.11Loosely attach one blade/flange assembly to the motorhub by securing the two 1/4-20 x .500” oval headcountersunk screws (Figure 11).

Repeat this procedure for other two blade assemblies.

Tighten all the 1/4-20 x .500” oval head countersunkscrews to the motor hub at this time.

NOTE: Take care not to scratch fan housing wheninstalling blades.

To reduce the risk of personal injury, do not bend theblade flange when installing the blade flanges,balancing the blades or cleaning the fan. Do not insertforeign objects in between rotating fan blades.

WARNING!


9



The outlet box and joist must be securely mounted andcapable of supporting at least 50 lbs. Use only a U.L.outlet box listed as “Acceptable for Fan Support of 22.7kg. (50 lbs.) or less”.

WARNING!

To reduce the risk of fire, electric shock, or personalinjury, mount fan to outlet box marked “Acceptable forFan Support of 22.7 kg. (50 lbs.) or less”, and use screwssupplied with outlet box. Most outlet boxes commonlyused for support of light fixtures are not acceptable forfan support and may need to be replaced. Consult aqualified electrician if in doubt.

WARNING!

4.1Securely attach the hanger bracket to the outlet box usingthe two screws supplied with the outlet box. (Figure 13).

Hanger bracket must seat firmly against outlet box. If theoutlet box is recessed, remove wall board until bracketcontacts box. If bracket and/or outlet box are not securelyattached, the fan could wobble or fall.

WARNING!

TWO SCREWSSUPPLIED WITHOUTLET BOX HANGER BRACKET

ANTI-ROTATION TAB

OUTLET BOX

Figure 13

FLOOR

CEILING

AT LEAST

7'

Figure 12

4. How to Hang Your Ceiling Fan

The fan must be hung with at least 7' of clearance fromfloor to blades (Figure 12).

WARNING!



4. How to Hang Your Ceiling Fan (Continued)

To avoid possible fire or shock, do not pinch wiresbetween the hanger ball/downrod assembly and hangerbracket.

WARNING!

Failure to seat tab in groove could cause damage toelectrical wires and possible shock or fire hazard.

WARNING!

OUTLETBOX

HANGERBRACKET

HANGER BALL/DOWNROD ASSEMBLY

NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY.

HANGER BRACKET

HANGER BALL

HANGER BALL GROOVE

ANTI-ROTATION TAB

Figure 14

4.2Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was justattached to the outlet box (Figure 14).

Be sure the groove in the ball is engaged with the anti-rotation tab on the hanger bracket (Figure 14).


11



5. Final Assembly

SWITCHHOUSING COVER

SWITCH HOUSINGCOVER CONNECTOR

MOTOR HUBCONNECTOR

SWITCHHOUSINGADAPTER

Figure 16

5.2The two connectors are keyed and color-coded and mustbe mated correctly (same color-to-color) before they canbe engaged.

Engage the connector of the switch housing cover with themotor hub connector (Figure 16).

Make sure the connector latch closes properly.

SWITCHHOUSINGCOVER

POSITION COVERON ADAPTER

LARGE SLOT

#6-32 x 0.375"PAN HEADSCREWS (3)

Figure 17

5.3Tuck all the wires and connectors into the switch housingadapter.

Position the switch housing cover so that the reverseswitch fits into the large slot of the switch housing adapter(Figure 17).

Align the three screw holes of the switch housing cover.

Secure the switch housing cover to the switch housingusing the three #6-32 x 0.375” pan head screws (suppliedin parts bag) (Figure 17).

SWITCHHOUSINGADAPTER

MOTOR HUB

ROTATEADAPTERCLOCKWISE

#6-32 x 0.312"FLAT HEAD SCREW

MOTOR HUBCONNECTOR

Figure 15

5.1Remove one #6-32 x 0.312” flat head screw from the motorhub and retain for later use.

Loosen the other two #6-32 x 0.312” flat head screws on themotor hub for the installation of the switch housing adapter.

Place the motor hub connector through the center hole of theswitch housing adapter.

Place the switch housing adapter onto the motor hub,aligning the three screw holes (Figure 15).

Rotate the switch housing adapter key hole slots counter-clockwise to engage both loosened screws (Figure 15).

Reinstall the previous removed screw.

Secure the switch housing to the motor hub by tightening thethree switch housing screws.

Spare #6-32 x 0.312” flat head screw supplied in parts bag.


LISTED WIRECONNECTOR

SUPPLY WHITE (NEUTRAL)

FAN MOTOR WHITE WIRE

Figure 19

6.2Securely connect the fan motor white wire to the supplywhite (neutral) wire using wire connector (supplied) (Figure19).

If you feel that you do not have enough electricalwiring knowledge or experience, have your faninstalled by a licensed electrician.

6.1Connect the green grounding lead from the hanger balland the green grounding lead from the hanger bracket tothe grounding conductor of supply (this may be a barewire or wire with green colored insulation). Securelyconnect wires with wire connectors (supplied) (Figure 18).

6. How to Wire Your Ceiling Fan

To avoid possible electrical shock, be sure electricity isturned off at the main fuse box before wiring.NOTE: If you are not sure if the outlet box is grounded,contact a licensed electrician for advice, as it must begrounded for safe operation.

WARNING!


WARNING!

GROUND CONDUCTOR SUPPLY

LISTED WIRE CONNECTOR

GREEN WIRE(GROUND) FROMHANGER BRACKET

GREEN WIRE(GROUND) FROMHANGER BALL

Figure 18



13



6. How to Wire Your Ceiling Fan (Continued)

FAN MOTOR BLACK WIRE

SUPPLY BLACK(HOT)

LISTED WIRECONNECTOR

Figure 20

6.3Securely connect the fan motor black wire to the supplyblack (hot) wire using wire connector (supplied)(Figure 20).

BLACK WIRESWHITE WIRES

GREEN WIRES

Figure 21

6.4After connections have been made, turn leads upward andcarefully push leads into the outlet box, with the white andgreen leads on one side of the outlet box and position theblack lead on the other side of the outlet box (Figure 21).

Check to see that all connections are tight, includingground, and that no bare wire is visible at the wireconnectors, except for the ground wire. Do notoperate fan until blades are in place. Noise and fandamage could result.

WARNING!



6. How to Wire Your Ceiling Fan (Continued)

CEILING COVER

LOCKWASHERS (2)

THREADEDSTUDS (2)

KNURLEDKNOBS (2)

Figure 23

To avoid possible fire or shock, make sure that the electricalwires are completely inside the outlet box and not pinchedbetween the ceiling cover and the ceiling.

WARNING!

6.6Lift the ceiling cover up to the threaded studs and turn untilstuds protrude through the holes in the ceiling cover(Figure 23).

Secure the ceiling cover in place by sliding lockwashersover the threaded studs and installing the two knurledknobs (supplied). (Figure 23).

Tighten the knurled knobs securely until the ceiling coverfits snugly against the ceiling and the hole in the ceilingcover is clear of the downrod.

6.5Screw the two threaded studs (supplied) into the tappedholes in the hanger bracket (Figure 22).

THREADED STUDS (2)

Figure 22


15



7.1This control is designed to operate only one ceiling fan

Before disconnecting power, ensure that the fan is set atthe highest speed.

NOTE: Electric connections should be in accordancewith the National Electrical Codes and all LocalCodes. Before starting, disconnect power to thecircuit at the fuse box or circuit breaker panel.

Remove the faceplate and screws from the existing wallswitch. Pull switch out from wall outlet box.

Disconnect the wire from the existing fan wall switch(Figure 24).

7. Installing the Wall Control

FACEPLATE

WALL SWITCH

WALL OUTLET BOX

SCREWSFigure 24

7.2Slide the Fan Control to the OFF position (0).

Connect one BLACK wire from the Fan Control to thefacility active BLACK wire with a wire connector (provided)(Figure 25).

Connect the other BLACK wire from the Fan Control to theoutlet box active BLACK wire with a wire connector(provided with control) (Figure 25).

NOTE: Use wire connectors (supplied) to secureelectrical connections.

TO NEUTRALTO FAN MOTOR LOAD

TO 120VACSOURCE

HOT

BLACK

BLACK

4

0

3

2

1

BLACK

BLACK

Figure 25

Turning off wall switch is not sufficient. To avoid possibleelectrical shock, be sure electricity is turned off at themain fuse box before wiring. All wiring must be inaccordance with National and Local codes and the ceilingfan must be properly grounded as a precaution againstpossible electrical shock.

WARNING!


7. Installing the Wall Control (Continued)

7.3Attach the SW46W Fan Control to the wall outlet box withtwo 6-32 x 3/4” screws (provided with control).

Position the faceplate (provided with control) onto thespeed control. Using the two 6-32 x 1/4” screws, screw thefaceplate and speed control to the wall outlet box (Figure26).

Restore power at the main fuse box or circuit breakerpanel.

6-32 x 1/4" SCREWS (2)FACEPLATE

SW46 FAN CONTROL

WALL OUTLET BOX

4

0

3

2

1

6-32 x 3/4"SCREWS (2)

Figure 26


8.1IMPORTANT

Fan installation must be completed, including theinstallation of the fan blades, before testing of thecontrols.

Restore electrical power to the outlet box by turning theelectricity on at the main fuse box.

Check the operation of the fan by sliding the bar of thecontrol through the four positions marked 1 - 4(“0” position is OFF) (Figure 27).

8. Using Your Ceiling Fan

4

0

3

2

1

Figure 27

8.2All fans are shipped from the factory with the reversingswitch positioned to circulate air downward. If airflow isdesired in opposite direction, turn your fan OFF and waitfor the blades to stop turning, then slide the reversingswitch to the opposite position, and turn fan on again(Figure 28).

The fan blades will turn in the opposite direction andreverse the airflow.

Reverse Switch InformationSeason Rotation Direction Switch PositionSummer Counter-Clockwise RightWinter Clockwise Left

REVERSING SWITCH

Figure 28


17




WARNING!See your local Emerson dealer, www.emersonfans.com orthe Emerson Ceiling Fan catalog for these accessories:· Ceiling Fan Controls· Downrod Extension Kits

10. Accessories

The use of any other control not specifically approved forthis fan could result in fire, shock and personal injury.

WARNING!

Do not use water when cleaning your ceiling fan.It could damage the motor or the blades and create thepossibility of an electrical shock.

WARNING!IMPORTANT CARE INSTRUCTIONS

for your Ceiling Fan

Periodic cleaning of your new ceiling fan is the onlymaintenance that is needed.

When cleaning, use only a soft brush or lint free cloth toavoid scratching the finish.

Abrasive cleaning agents are not required and should beavoided to prevent damage to finish.

9. Maintenance



11. Repair Parts

PARTS BAG

8

7

6

5

4

14

9

11

10

12

13

3

15

16

17

7

8

9

12

13

4

0

3

2

1

23

18

19

11

21

12

5

6

10

20

22


19



11. Repair Parts Listing

Before discarding packaging material, be certain all parts have been removed.

HOW TO ORDER REPAIR PARTS

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:

• PART NUMBER • NAME OF ITEM• PART DESCRIPTION • MODEL NUMBER

The model number of your Fan will be found on a label attached to the top housing.

For repair parts, phone 1-800-654-3545.

Model Numbers

KeyNo. Description CF320BS00 CF320SW00

* Hanger Ball Assembly, 761655-17 761655-92Consisting of:

1 Hanger Bracket — —2 Hanger Ball — —3 4.5” Downrod — —

* Parts Bag Containing: 764769-CRM 764769-SW4 Wire Connectors (5) — —5 Studs, Threaded, #8-32 x 1-1/4” (2) — —6 Lockwashers, External Tooth, #8 (2) — —7 Knobs, Knurled, #8-32 (2) — —8 Pin, Clevis (1) — —9 Clip, Hairpin (1) — —10 Washer Head Screws #8-32 x 0.312” (10) — —11 Oval Head Countersunk Screws, 1/4-20 x .500” (7) — —12 Flat Head Screw, #6-32 x 0.312”, Spare (1) — —13 Pan Head Screws, #6-32 x 0.375” (4) — —14 Balancing Kit (1) — —

15 Ceiling Cover 764503-BS 764503-SW16 Motor Coupler Cover 764757-BS 764757-SW17 Switch Housing Adapter 764766-BS 764766-SW18 Reverse Switch and Aux. Cap Harness 764768-BLK 764768-WHT19 Switch Housing Cover 764767-BS 764767-SW20 Fan Blade Flanges (set of 3) 764763-BS 764763-SW21 Fan Blades (set of 3)22 Decorative Blade Nuts (9) 764765-BS 764765-SW23 Wall Control SW46W SW46W— Owner's Manual BP7514 BP7514

764761-BS/BQ, NC/WA, or SW/MP


FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORETROUBLESHOOTING YOUR FAN.

WARNING!


13. Troubleshooting

TROUBLE PROBABLE CAUSE SUGGESTED REMEDY

1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers.

2. Reversing switch in neutral position. 2. Make sure reversing switch position is all the way to one side.

2. Fan sounds 1. Blades not attached to fan. 1. Attach blades to fan before operating.noisy. 2. Loose screws in motor housing. 2. Check to make sure all screws in motor housing

are snug (not over-tight).3. Screws securing fan blade flanges to 3. Check to make sure the screws which attach

motor hub are loose. the fan flanges to the motor hub are tight. 4. Screws holding blades to flanges 4. Tighten screws securely.

are loose.

3. Fan wobbles 1. Setscrew in motor coupling is loose. 1. Tighten both setscrews securely in the motor coupling.excessively. 2. Setscrew in hanger ball/downrod 2. Tighten the setscrew in the hanger ball/downrod

assembly is loose. assembly.3. Screws securing fan blade flanges to 3. Check to be sure screws which attach the fan

motor are loose. blade flanges to the motor are tight.4. Fan blade flanges not seated properly. 4. Check to be sure the fan blade flanges seat

firmly and uniformly to the surface of the motor.If flanges are seated incorrectly, loosen the flange screws and retighten according to theprocedure in the section on "Ceiling Fan Assembly”.

5. Hanger bracket and/or ceiling outlet 5. Tighten the hanger bracket screws to the outlet box is not securely fastened. box, and/or secure outlet box.

6. Fan blades out of balance. 6. Interchanging an adjacent (side-by-side) blade pair can redistribute the weight and result in smoother operation.

Ceiling fan performance and energy savings rely heavilyon the proper installation and use of the ceiling fan. Hereare a few tips to ensure quality and product performance.

Choosing the Appropriate Mounting Location. Ceilingfans should be installed, or mounted, in the middle of theroom and at least 2.1 m above the floor and 46 cm fromthe walls. If ceiling height allows, install the fan 2. 5 m -2.75 m above the floor for optimal airflow. Consult yourEmerson Retailer for optional mounting accessories.Using the Ceiling Fan Year Round. In the summer, usethe ceiling fan in the counter-clockwise direction. The

12. Energy Efficient Use of Ceiling Fansairflow produced by the ceiling fan creates a wind-chilleffect, making you "feel" cooler. Select a fan speed thatprovides a comfortable breeze, lower speeds consumeless energy. In the winter, reverse the motor and operatethe ceiling fan at low speed in the clockwise direction. Thisproduces a gentle updraft, which forces warm air near theceiling down into the occupied space. Remember to adjustyour thermostat when using your ceiling fan - additionalenergy and dollar savings could be realized with thissimple step!

Turn Off When Not in the Room. Ceiling fans coolpeople, not rooms. If the room is unoccupied, turn off theceiling fan to save energy.

Make sure main power is turned OFF.

WARNING!


21



Emerson Air Comfort Ceiling Fan Limited WarrantyWhat The Limited Warranty Covers:This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the originalretail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components andaccessories of the Emerson Ceiling Fan against all defects in workmanship and materials.What The Period Of Coverage Is:This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner'sManual or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are coveredby this limited warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANYIMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE ORPROVINCE SHALL COVER THE MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TOCOMPONENTS AND ACCESSORIES.No Other Express or Implied Warranty Applies:THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILINGFAN, AND ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE,WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED ORMANUFACTURED FOR YOUR USE OR PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION,IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THEONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIMEOF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROMSTATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.What We Will Do To Correct Problems:If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if duringthe expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials orworkmanship, you must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defectivemotor, component or other accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and noreplacement Emerson Ceiling Fan can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or thereplacement Emerson Ceiling Fan to you at no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan.How You Can Receive Warranty Service:You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You canreturn your Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at 1-800-237-6511 to obtain a return authorization and serviceidentification tag. In order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have thatinformation readily available when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call EmersonCustomer Service, prior to your call please be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your returnauthorization request, we will provide you with a postage paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed atthe end of this limited warranty. The return label will be sent to the mailing address you provide to us by phone. What Is Not Covered:This limited warranty does not extend to and expressly excludes:• The glass globes and light bulbs of your Emerson Ceiling Fan, • Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship,• Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center,

use of parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse,modifications or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession,

• Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual.

This limited warranty is deemed null and void upon the occurrence of either of the following events:• You cease to own the Emerson Ceiling Fan product, or• The Emerson Ceiling Fan is moved from its original point of installation.This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent,dealer or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co.Limitation of LiabilityREPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BYLAW, IN NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIALDAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILINGFAN OR FOR THE NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY INPERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANYINDIVIDUAL USING THE EMERSON CEILING FAN EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequentialdamages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property orequipment.How State and Provincial Law Relates To The Warranty:Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.


Questions, problems, missing parts: Before returning to the store callEmerson Electric Customer Service

8 a.m. - 6 p.m., Eastern, Monday-Friday

1-800-654-3545

www.emersonfans.com

Retain this manual for future use.

Air Comfort ProductsDIVISION OF EMERSON ELECTRIC CO.

8100 W. Florissant • St. Louis, MO 63136

Part No. F40BP75140000 Form No. BP7514Revision: 151218 ETL Model No.: CF320

Printed in China12/15

SERIAL NUMBER: DATE CODE:

The serial number of this fan can be found on the nameplate on top of the fan housing. The date code can befound on the carton and on top of the fan housing, stamped in ink on a white label. You should record this dataabove and keep it in a safe place for future use.


KEANE - Lowe'spdf.lowes.com/installationguides/1000319197_install.pdf · KEANE™ 52” Ceiling Fan Owner's Manual Model Numbers CF320BS00 - Brushed Steel CF320SW00 - Satin White

Documents