Page 1
Kinder and Co. Pty. Ltd. Copyright © 2008 ABN 28 006 489 238
+61 (3) 9587 9244 +61 (3) 9587 9344 [email protected] www.kinder.com.au
K-Tra iner Be l t Al ignment Id ler
K-Trainer is an all-purpose conveyor belt alignment
idler, that will direct the belt correctly under all
operating conditions.
The two inverted vee rollers, put pressure down onto the belt,
promoting centralised belt training. The universal frame adjusts to
all types of mounting structures and is suitable for reversing belts.
After installation, the unit requires no further attention.
As the return strand of the belt is critical to maintain correct
belt alignment the K-Trainer is ideally installed just after the head
pulley, or prior to the tail pulley.
By having the return strand of the belt running true, this will help
direct the carry side of the belt and therefore minimise material
spillage and belt damage.
•Limits Belt Damage
•Controls Spillage
•Easily Installed
•Suitable for reversing belts
•Universal Fit
•Available for all belt widths
Page 2
Kinder and C
o. Pty. Ltd. Copyright ©
2008 ABN
28 006 489 238
+61 (3) 9587 9244 +
61 (3) 9587 9344 [email protected]
.au ww
w.kinder.com
.au
K-T
rainer B
elt Align
men
t Idler
Specifications subject to change without notice.
Certified draw
ings are available on request.
Page 3
Kinder and Co. Pty. Ltd. Copyright © 2008 ABN 28 006 489 238
+61 (3) 9587 9244 +61 (3) 9587 9344 [email protected] www.kinder.com.au
Tru-Trac ® Conveyor Be l t Track ing System
Tru-Trac® Conveyor Belt Tracking System is an
innovative and versatile mechanism, which will
operate with all belt types and environments in both
wet and dry conditions. The range covers solutions
for trough (load carrying) and return types on slow
moving, reversible, high speed and high load belts.
The internal vertical pivot axis unique tracking action causes
the unit to “kick in” immediately the belt starts to drift off
center. It does not rely on belt edge contact.
The Tru-Trac® incorporates a rubber covered crown face
which causes the drum to pivot about the perpendicular axis
and this results in the tracking action always being on the
same horizontal plane as the belt.
•Suitable for wet and dry conditions
•Requires minimum force to activate
•Does not rely on belt edge contact
•Simple to install
•Maintenance free
•Adjustable mounting brackets
Page 4
Kinder and Co. Pty. Ltd. Copyright © 2008 ABN 28 006 489 238
+61 (3) 9587 9244 +61 (3) 9587 9344 [email protected] www.kinder.com.au
Tru-Trac ® Conveyor Be l t Track ing System
Trough Tracker
Specifically designed for the load carrying side. Wing rollers
are incorporated into the standard pivot system. Suitable
for all troughing angles 15 to 45 degree. The unit utilizes
the center roller to steer where the most effective steering
forces are exerted.
Flat Return Tracker
Works well with reversible and shuttle conveyors and suitable
for belt speeds up to 7 meters / second.
Dual Return Tracker
Designed to accommodate excessive forces encountered
with wide belts and heavy loads. Two separate tapered
rollers are mounted onto the pivot mechanism.
Guidelines for Installation
•Only required where misalignment occurs. As a general
rule one unit is sufficient to align 50 meters of belt. On
very long belts spacing may be increased upto 100 meters.
•One unit is needed to keep the beltrunning center through
the gravity take up.
•Works equally well with reversible and shuttle conveyors.