This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Design and specifications are subject to change without notice.
AMPLIFIERPower Output 20 W RMS × 4 Channels at 4 Ω and < or = 1% THD+NSignal-to-Noise Ratio 80 dBA (reference 1 W into 4 Ω)Load Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60.0 Hz, 150.0 Hz, 400.0 Hz, 1.0kHz, 2.5kHz, 6.3kHz, 15.0kHz
Level ±10 dBAudio Output Level LINE OUT (FRONT/ REAR)/CENTER OUT/ SUBWOOFER OUT
Color System NTSCVideo Output (composite) 1 Vp-p/75 ΩOther Terminals Input LINE IN, VIDEO IN, USB input terminal, Antenna input
Output 2nd AUDIO OUT, VIDEO OUTOthers CD changer, OE REMOTE
FM/AM TUNERFrequency Range FM (with channel interval set to 100 kHz or 200 kHz) 87.5 MHz to 107.9 MHz
FM (with channel interval set to 50 kHz) 87.5 MHz to 108.0 MHzAM (with channel interval set to 10 kHz) 530 kHz to 1 710 kHzAM (with channel interval set to 9 kHz) 531 kHz to 1 602 kHz
FM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)Alternate Channel Selectivity (400 kHz) 65 dBFrequency Response 40 Hz to 15 000 HzStereo Separation 35 dB
AM Tuner Sensitivity/Selectivity 20 µV/35 dBDVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels : 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System PAL/NTSCAspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to + 60°C (14°F to 140°F)Allowable Operating Temperature 0°C to + 40°C (32°F to 104°F)
USBUSB Standards USB 2.0 Full Speed
Full Speed : Maximum 12 MbytesData Transfer Rate Low Speed : Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12
BLUETOOTHVersion Bluetooth 1.2 certifiedOutput Power +4 dBm Max. (Power class 2)Service Area Within 10 m (10.9 yd)Profile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1A2DP (Advanced Audio Distribution Profile) 1.2AVRCP (Audio/Video Remote Control Profile) 1.3
GENERALPower Requirements DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°C (32°F to 104°F)Dimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
(7-3/16” × 2-1/16” × 6-5/16”)Panel Size (approx.) 188 mm × 58 mm × 12 mm
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60.0 Hz 150.0 Hz 400.0 Hz 2.5kHz 6.3kHz 15.0kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
DVD/CDSignal Detection System Non-contact opticalFrequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System PAL/NTSC
Aspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to + 40°CUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 VVersion Bluetooth 1.2 certifiedOutput Power +4 dBm Max. (Power class 2)Service Area Within 10 mProfile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1A2DP (Advanced Audio Distribution Profile) 1.2AVRCP (Audio/Video Remote Control Profile) 1.3
Power Requirements Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to + 40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
1-4 (No.MA401<Rev.001>)
KD-AVX44EE
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Load Impedance Frequencies 60.0 Hz, 150.0 Hz, 400.0 Hz, 1.0kHz, 2.5kHz, 6.3kHz, 15.0kHzEqualizer Control Range Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
DVD/CDSignal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System PAL/NTSCAspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°C
USBUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 V
BLUETOOTHVersion Bluetooth 1.2 certifiedOutput Power +4 dBm Max. (Power class 2)Service Area Within 10 mProfile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1A2DP (Advanced Audio Distribution Profile) 1.2AVRCP (Audio/Video Remote Control Profile) 1.3
GENERALPower Requirements Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
(No.MA401<Rev.001>)1-5
KD-AVX44U
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionSignal-to-Noise Ratio 70 dBLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60.0 Hz 150.0 Hz 400.0 Hz 1.0kHz 2.5kHz 6.3kHz 15.0kHz
Level ±10 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
Color System NTSC/PALVideo Output (composite) 1 Vp-p/75 ΩOther Terminals Input LINE IN VIDEO IN USB input terminal Antenna input
Output 2nd AUDIO OUT, VIDEO OUTOthers CD changer
FM/AM TUNERFrequency Range FM 87.5 MHz to 108.0 MHz
AM 531 kHz to 1 602 kHzFM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)Alternate Channel Selectivity (400 kHz) 65 dBFrequency Response 40 Hz to 15 000 HzStereo Separation 35 dB
AM Tuner Sensitivity/Selectivity 20 µV/35 dBDVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PALAspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°C
USBUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 V
BLUETOOTHVersion Bluetooth 1.2 certifiedOutput Power +4 dBm Max. (Power class 2)Service Area Within 10 mProfile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1A2DP (Advanced Audio Distribution Profile) 1.2AVRCP (Audio/Video Remote Control Profile) 1.3
GENERALPower Requirements Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm ×160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
1-6 (No.MA401<Rev.001>)
KD-AVX44UT
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionSignal-to-Noise Ratio 70 dBLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60.0 Hz 150.0 Hz 400.0 Hz 1.0kHz 2.5kHz 6.3kHz 15.0kHz
Level ±10 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
Color System NTSC/PALVideo Output (composite) 1 Vp-p/75 ΩOther Terminals Input LINE IN VIDEO IN USB input terminal Antenna input
Output 2nd AUDIO OUT, VIDEO OUTOthers CD changer
FM/AM TUNERFrequency Range FM 87.5 MHz to 108.0 MHz
AM 531 kHz to 1 602 kHzFM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)Alternate Channel Selectivity (400 kHz) 65 dBFrequency Response 40 Hz to 15 000 HzStereo Separation 35 dB
AM Tuner Sensitivity/Selectivity 20 µV/35 dBDVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PALAspect Ratio 16:9 (wide)Allowable Storage Temperature -1°C to +60°CAllowable Operating Temperature 0°C to +40°C
USBUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 V
BLUETOOTHVersion Bluetooth 1.2 certifiedOutput Power +4 dBm Max. (Power class 2)Service Area Within 10 mProfile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1A2DP (Advanced Audio Distribution Profile) 1.2AVRCP (Audio/Video Remote Control Profile) 1.3
GENERALPower Requirements Operating Voltage: DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
(No.MA401<Rev.001>)1-7
KD-AVX44A
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionSignal-to-Noise Ratio 70 dBLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60.0 Hz 150.0 Hz 400.0 Hz 1.0kHz 2.5kHz 6.3kHz 15.0kHz
Level ±10 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
Color System NTSC/PALVideo Output (composite) 1 Vp-p/75 ΩOther Terminals Input LINE IN VIDEO IN USB input terminal Antenna input
Output 2nd AUDIO OUT, VIDEO OUTOthers CD changer
FM/AM TUNERFrequency Range FM 87.5 MHz to 108.0 MHz
AM 531 kHz to 1 602 kHzFM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)Alternate Channel Selectivity (400 kHz) 65 dBFrequency Response 40 Hz to 15 000 HzStereo Separation 35 dB
AM Tuner Sensitivity/Selectivity 20 µV/35 dBDVD/CD
Signal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System NTSC/PALAspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°C
USBUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 V
BLUETOOTHVersion Bluetooth 1.2 certifiedOutput Power +4 dBm Max. (Power class 2)Service Area Within 10 mProfile HFP (Hands-Free Profile) 1.5
OPP (Object Push Profile) 1.1A2DP (Advanced Audio Distribution Profile) 1.2AVRCP (Audio/Video Remote Control Profile) 1.3
GENERALPower Requirements Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
1-8 (No.MA401<Rev.001>)
KD-AVX22E
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionLoad Impedance Frequencies 60.0 Hz 150.0 Hz 400.0 Hz 1.0kHz 2.5kHz 6.3kHz 15.0kHzEqualizer Control Range Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
DVD/CDSignal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System PAL/NTSCAspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°C
USBUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 V
GENERALPower Requirements Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
(No.MA401<Rev.001>)1-9
KD-AVX22EE
Design and specifications are subject to change without notice.
AMPLIFIERMaximum Power Output Front/Rear 50 W per channelContinuous Power Output (RMS) Front/Rear 20 W per channel into 4 Ω 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortionLoad Impedance 4 Ω (4 Ω to 8 Ω allowance)Equalizer Control Range Frequencies 60.0 Hz 150.0 Hz 400.0 Hz 1.0kHz 2.5kHz 6.3kHz 15.0kHz
Level ±10 dBSignal-to-Noise Ratio 70 dBAudio Output Level LINE OUT (FRONT/REAR)/CENTER OUT/ SUBWOOFER OUT
DVD/CDSignal Detection System Non-contact optical pickup (semiconductor laser)Frequency Response DVD, fs=48 kHz 16 Hz to 22 000 Hz
DVD, fs=96 kHz 16 Hz to 44 000 HzVCD/CD 16 Hz to 20 000 Hz
Dynamic Range 93 dBSignal-to-Noise Ratio 94 dBWow and Flutter Less than measurable limit
MONITORScreen Size 3.5 inch wide liquid crystal displayNumber of Pixel 211 200 pixels: 960 (horizontal) × 220 (vertical)Drive Method TFT (Thin Film Transistor) active matrix formatColor System PAL/NTSCAspect Ratio 16:9 (wide)Allowable Storage Temperature -10°C to +60°CAllowable Operating Temperature 0°C to +40°C
USBUSB Standards USB 2.0 Full SpeedData Transfer Rate Full Speed: Maximum 12 Mbytes
Low Speed: Maximum 1.5 MbytesCompatible Device Mass storage classCompatible File System FAT 32/16/12Max. Current Less than 500 mA/5 V
GENERALPower Requirements Operating Voltage DC 14.4 V (11 V to 16 V allowance)Grounding System Negative groundAllowable Operating Temperature 0°C to +40°CDimensions (W × H × D) Installation Size (approx.) 182 mm × 52 mm × 160 mm
Panel Size (approx.) 188 mm × 58 mm × 12 mmMass (approx.) 2.2 kg (excluding accessories)
1-10 (No.MA401<Rev.001>)
SECTION 1PRECAUTION
1.1 Safety Precautions
! Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
! Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
(No.MA401<Rev.001>)1-11
1.2 Preventing static electricityElectrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laserdiode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricityStatic electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbenchGround the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing thetraverse unit (optical pickup) on it.
(2) Ground yourselfUse an anti-static wrist strap to release any static electricity built up in your body.
(3) Handling the optical pickup• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easilydestroy the laser diode.
1.3 Handling the traverse unit (optical pickup)(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long atime when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4 Attention when traverse unit is decomposed*Please refer to "Disassembly method" in the text for the pickup unit. • Apply solder to the short land before the card wire is disconnected from the connector on the pickup unit.
(If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.)• In the assembly, be sure to remove solder from the short land after connecting the card wire.
1M
(caption)
Anti-static wrist strap
Conductive material
(conductive sheet) or iron plate
Solder short part
1-12 (No.MA401<Rev.001>)
1.5 Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able to function.
6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure.
REPRODUCTION AND POSITION OF LABELS and PRINT
! Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
WARNING LABEL and PRINT
(No.MA401<Rev.001>)1-13
SECTION 2SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
SECTION 3DISASSEMBLY
3.1 Main body ( Used figure are KD-AVX44J )3.1.1 Removing the Heat sink(See Fig.1)
(1) Remove the two screw A and two screws B attaching theHeat Sink.
Fig.1
A
B
1-14 (No.MA401<Rev.001>)
3.1.2 Removing the top Chassis(See Fig.2 to 4)(1) From the side of the main body, remove the two screw C
attaching the both side of Top chassis.(See Fig.2)(2) From the bottom side of the main body, remove the two
screws D attaching the Top chassis.(See Fig.3)(3) From the back side of the main body, remove the four
screws E attaching the Top Chassis.(See Fig.4)
Fig.2
Fig.3
Fig.4
C
D
E
(No.MA401<Rev.001>)1-15
3.1.3 Removing the Main board(See Fig.5 and 6)(1) Remove the two screws F attaching the Rear bracket. (See
Fig.5)(2) Disconnect the connector wire from Gear bracket unit con-
nected to connector CN891 of the main board.(See Fig.6)(3) Disconnect the connector wire from motor connected to
connector CN881 of the Main board.(See Fig.6)(4) Disconnect the card wire from Front chassis connected to
connector CN962 of the Main board.(See Fig.6)(5) Remove the two screws G attaching the Main board.(See
Fig.6)(6) Slide the Main board to rear side and lift up it, then take out
the Main board.(See Fig.6)
Fig.5
Fig.6
3.1.4 Removing the DVD mechanism assembly.(See Fig.7)(1) Remove the three screws H attaching the DVD mechanism
assembly.(2) Disconnect the connector wire from Front chassis connect-
ed to connector CN399 of the Connection board.
Fig.7
F
CN962CN891
CN881
G
G
H
H
H
CN399
1-16 (No.MA401<Rev.001>)
3.1.5 Removing the Connection board assembly(See Fig.8)(1) Disconnect the card wire from DVD mechanism assembly
connected to connector CN1 and CN395 of the Connectionboard assembly.
(2) Remove the four screws J attaching the Connection boardassembly.
Fig.8
3.1.6 Removing the Rear cover(See Fig.9)(1) Remove the nine screws K attaching the Rear cover.
Fig.9
J
J
CN1
CN395
K
K
(No.MA401<Rev.001>)1-17
3.2 DVD mechanism3.2.1 Removing the Traverse mechanism assembly (See Fig.1 to 6)
(1) Solder the short land section on the flexible wire of pickup.(See Fig.1)
Caution:* Solder the short land section on the flexible wire of pickupbefore disconnecting the flexible wire form the connectorCN101 on the Front end board.If the flexible wire is disconnected without attaching thesolder, the pickup may be destroyed by static electricity.* When attaching the Traverse mechanism assembly, re-move the solder from the short land section after connectionthe flexible wire to the connector CN101 on the Front endboard.
(2) Voltage supply to TP79 and TP81 approx DC 3.0V untilClamper is shift to loading complete position. (See Fig.2)
(3) Disconnect the flexible wires from Traverse mechanism as-sembly connected to connector CN101 and CN164 of theFront end board. (See Fig.2)
(4) Remove the five screws A attaching the Top cover assem-bly. (See Fig.3)
(5) From the bottom side, disconnect the connector wire fromTop cover assembly connected to connector CN2 of theFront end board. (See Fig.4)
(6) From the bottom side, remove the spring from Traversemechanism assembly. (See Fig.5)
(7) From the top side, pull up the traverse mechanism and disengagethree dumper positions. (See Fig.6)
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
Solder short part
CEN
TERR21
D-
DG
ND
_7
R312
R31
7
WO
OFE
R
TP67
R35
7
TP79 TP81
TP92
Voltage supply
position
CN164
CN101
TP81
TP79
A
CN2
Dumper
(same color spring)
Dumper
(Different color spring)
1-18 (No.MA401<Rev.001>)
3.2.2 Removing the Front end board (See Fig.7)(1) Remove the Motor wires from loading motor soldered to
TP79 and TP81 of the Front end board.(2) Remove the two screws B attaching the Front end board.
Fig.7
3.2.3 Removing the Loading arm assembly (See Fig.8)(1) Remove the Loading arm spring L from Loading arm assembly.(2) Slide to left side and then disengage hook a then hook b.
Fig.8
BB
TP79
TP81
Loading armassembly
Loading arm spring L
hook a
hook b
(No.MA401<Rev.001>)1-19
3.2.4 Removing the Gear base assembly (See Fig.9, 10)(1) Remove the Loading arm spring L. (See Fig.9)(2) Remove the two screws C attaching the Gear base assembly.
(See Fig.10)
Fig.9
Fig.10
3.2.5 Removing the Loading arm holder. (See Fig.11)(1) Remove the two screws D attaching the Loading arm holder.(2) Remove the Loading arm spring R.
Fig.11
Loading armspring L
C
D
Loading arm
spring R
Loading arm
holder
1-20 (No.MA401<Rev.001>)
3.2.6 Removing the Loading moor assembly (See Fig.12)(1) Remove the three screws E attaching the Loading motor
assembly.
Fig.12
3.2.7 Removing the Slide cam assembly (See Fig.13)(1) Slide to backward the Slide cam assembly and the remove
the Slide cam spring.(2) Slide to frontward the slide cam assembly, and then take
out it.
Fig.13
3.2.8 Removing the Photo board (See Fig.14)(1) Pressing the hook c and then slide to backward (slide to the
arrow side) the Disc plate.(2) Remove the one screw F attaching the Photo board.
Fig.14
E
Slide cam assembly
Slide cam spring
hook c
hook c
F
Photo board
(No.MA401<Rev.001>)1-21
3.2.9 Removing the Loading motor (See Fig.15 to 18)(1) Remove the A wheel gear. (See Fig.15)(2) Remove the A worm gear, M connect gear and M wheel
gear by sequentially. (See Fig.16)(3) Remove the two screws G attaching the Loading motor.
(Se Fig.17)(4) When attaching the Loading motor, motor wire should arrange
to figure. (See Fig.18)
Fig.15
Fig.16
Fig.17
Fig.18
A Wheel gear
A worm gear
M connect gear
M wheel gear
G
Wire arrangement
1-22 (No.MA401<Rev.001>)
3.2.10 Removing the Roller assembly (See Fig.19)(1) Remove the Slit washer.(2) Remove the R middle gear.(3) Remove the R connect gear.(4) Snap off the part a of the Roller assembly.(5) Lift up the part b of the Roller assembly, and then release
part c (When release part c, R collar R is easy to come off,does not lose it).
CAUTION:When reattach the Roller assembly, Middle gear should keepdirection and Slit washer should be change new part.
Fig.19
3.2.11 Removing the Roller (See Fig.20)(1) Remove the Slit washer.(2) Pull out the Roller shaft.
CAUTION:When reattach the Roller shaft, Slit washer should be changenew part.
Fig.20
Direction
Slit washer
R connect gear
R collar R
R middle gear
part b
part a
part c
keep direction
slit
small side
keep directionslit
(No.MA401<Rev.001>)1-23
SECTION 4ADJUSTMENT
4.1 Test instruments required for adjustment(1) Digital oscilloscope (100MHz)(2) Electric voltmeter(3) Digital tester(4) Tracking offset meter(5) Test Disc : VT501 or VT502(6) Extension cable : EXTDV002-30P x1
EXTSH002-22P x1 EXTAV70X-50PF x1
(7) Extension studs : STDV001-3P
4.2 Standard measuring conditionsPower supply voltage DC14.4V(10.5 to 16V)Load impedance 20K.(2 Speakers connection)Output Level Line out 2.5V (Vol. MAX)
4.3 Standard volume positionBalance and Bass &Treble volume : lndication"0"Loudness : OFF
4.4 Dummy loadExclusive dummy load should be used for AM,and FM. For FM dummy load, there is a loss of 6dB between SSG outputand antenna input.The loss of 6dB need not be considered sincedirect reading offigures are applied in this working standard.
4.5 How to connect the extension cable for adjustingCaution:
Be sure to attach the heat sink and rear bracket onto the power amplifier IC and regulator IC respectively,before supply the power.If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.
Extension studs
STDV001-3P
Extension studs
STDV001-3P
Extension cable
EXTXD001-50PF
R3037
R3038
C3025
R3035
R3036
C3024
R3033R3034
IC397
C3014
IC394
R3133C3124
R3146
C3126
C3129
R3114
R3115
C3110
R3117
R3120
IC393
C3112
R3122
C3115
R3123
C3117
C3118
R3125R3127
R3
R3131
R3132 R3139
R3141
R3142
C3130C3131
C3015
C3013
C3108
C3111
C3113
C3123
C3125
C3132
C3133
R3134R3144R3135
C3121
R3150C
3135R
3157
C3136
R3158
C3137
R3159
C313
R316
C3140
C3141
R3172
R3173
C3105
C3106
C3107
R3011R3010
C3002
C3006C
3004
R3006R3007
IC399
CN
395
5C3156
Q373
C90
1
D984
Q842
R32
8
R857
C18
3
R329
R32
3
C17
3
C28
3
C27
3
R32
2
IC35
0
CN860
Q84
7
C845
C19
1
IC37
1
C32
3
C29
1
C325
R37
5C
376
C113
C213
R113
IC33
2
R858
R213
R341
R32
4
C32
1
C15
1
C16
1
C261
C25
1
R15
1R
161
R261
R373
C39
1
R251
C352
D86
1
R859
R30
8
R16
2
IC31
R15
2
C36
R25
2R
262
C31
C35
R34
8
C33C34
R34
0
R848Q843
D251
X31
Q84
5
R349
Q341
R36
C12
4
C32
4
D901
C121
R902
C221
L901
C90
2
Q251Q261
Q161Q151 R
264
R25
4
R15
4R
164
R37
7
C84
1
Q862C847
CN901
C122
D151
R210
C374
C192
C292
R183R173
R283R273
Q201
R35
2
C10
6
Q342
IC32
1
D846
R374
R37
6
Q101
C222
D84
7
C372
R852
C848
Q371
Q372C37
5
D371
C373
C22
9
Q84
8
C129
Q844C844
D845
D34
2
R378
R37
2
R110
C32
6
R37
0
C84
6
C172C182
C282C272
R856C849
Q84
9
R13
0R
140
R240
C22
4
R33
5R
334
C123C223
C86
6
R16
5
R26
5
C850
C852
C34
5
R344
D34
0
R346
R30
9
R325
R32
6
R30
6
C304C305
C30
6
C30
3
R303R305
R230
R30
7
R903
C37
C37
7
C20
6
C307
C378
D372
Q863 Q864
C33
6
C125
R21
9
R119
R33
6
D191D190
R311
R31
2
R8
R33
1
R33
7
R38
R39
R866
Q374
R962
R9923
R961
C99
26
IC93
5
IC934
R925
D921
C921
C9927
C925
C923
R99
26
R937
C99
30C9906R9927
RA729
R926
R99
25
C9905
R93
4
R932
R92
3
C99
25
D922
R9924
C215
R34
7
R20
9
R10
9L1
01
R115
L201
R215R15
3
R11
6
R16
3
R21
6
R26
3
R25
3 C115
R34
2
C23
C9
C10
C11
C12
C13
C14
C16
C17
C18
C19 R14
C20
R16
C21
L2
C22
R19R20
R21
C24 IC
11
C25
L5
C26
R22 C27
C28
R23
C29
X1L6
C30
C41
R10
R15
C42
L8
C44
L9
L10
C45 D
11
D12
W1
R11
R18
CN931
R9
C38
C32R13
R34
R35
L1
C8
C7
C5
TH721
C863
C46L11R17
CN921
R22
5
R125
R338
R330
R98
R99
L3
IC92
1
CN911
R740
RA7
27
C80
1
RA730
IC88
1
C805
Q95
2Q
953
R71
2
D96
4
R770
R72
9
R771
D965
Q701
R947
IC801
R946
D96
6
R94
2
R943
R944
R94
5R
949
C94
4
D96
7
R72
3
R775
R70
9
R714
Q881
R766
X702
R98
7
R95
5
R956
CN861
C88
1
CN881
IC721
R76
9
R768
C72
1R
773
C713
R78
1
R72
4
R71
6
R730R732
R704
R71
7
R75
9
IC93
3
D991
R80
82
R767
R804
R73
6
R735
R79
8
C808
D97
2
R71
5
C927R73
9
D97
3
R71
3
R784IC73
1
R78
3
C731
D731
C716
C809
C715
C97
3
C974
C811
R70
01
R72
8
R984
R986
C800
IC701
R702R703
R711
D97
4
D97
5
R9997
IC94
1
IC942
C94
2
R90
9
R90
6
C702
C70
1
R733
C82
7
C8026
C8031
Q80
83R
8089
R80
83C
8082
Q8052Q8053
R80
51
R80
53
R80
52
C80
52
C80
63
R8061C8062
C80
61
R8091
C80
58
C80
22
C80
14
D8041
L8041
R80
59
Q8042
R80
42
C80
48R
8043
R80
44
Q8043
IC80
3
IC80
4C
8071
IC823
R82
09R
8231
R82
08
D9002D9003
R8029
C80
47
R8049 R8048
R80
47
R80
46
C9102
R80
45
R80
37C
8035
C80
34
R80
23
R8022
R8085
R8021
Q8023
Q80
22 R80
75R
8076
R80
73R
8074
C80
75Q
8005
R80
34 R80
33
C80
74
R8084
R80
62
D8011
C8042
Q8012Q8013
R8041
Q806
R80
7
R806
R71
0
X701
C80
44
C80
43
C80
36
C80
27
L8021
L8051
L801
1
R9996
D8061D8062
C80
12
C80
33
C80
73C
8072
R80
63
R8011R8010
R80
64
IC822
D807
C812
R82
10
Q80
07
Q8093
Q8092
Q80
11
C73
2
D8068
D80
69D
8067
Q8091
R8214
C8013
R81
02
Q80
98
D8065
R8103
Q80
95
Q80
96
R81
05
Q8097R8104 D8066
Q8094
D80
63 R8101
Q8051
D8051
R8108
Q8021
R8112
C80
02
C83
1
C80
03
R774
RA7
24
R82
0 R810
R8111
D844
R84
6
C80
54
C8018
C807
R8107
D8075
R963
R8120 Q95
5
R97
1
R972
C80
85
C8087 C80
86
R973
F801
L701
R78
5
R23
1
L827
C23
1
CN891
CN962
BZ951
CN871
L841
L842
R75
5
R82
41
R82
11
R8232
R8234
Q8041
R80
38
R81
13
R81
14
C952
D80
8
L931
R76
5
Q804
R70
03R
779
C80
01
C8004
C8005
D80
01
D8002
D80
03D
8004
RA7
28
C93
1
D80
10
Q80
01
Q8002
C80
06
R70
0
R786
R79
0
R79
5
R796
R80
02
TH70
0
CN922
TP72
1
TP72
2
TP72
3TP
724
TP72
5
TP726
R96
5
D96
3
D96
9
D96
2
D97
0
D961
D96
8
R75
6
R96
0
R803
C92
14
C92
04
RA726 RA725
RA722RA723
R737
R73
8
RA7
21
Q8006
R75
7
R82
1
R8006
R958
R92
4
D97
1
PP1
R92
2C
922
D8007
PP2
PP3
PP4
EXTSH002-22P
EXTDV002-30P
EXTAV70X-50PF
1-24 (No.MA401<Rev.001>)
4.6 Service mode4.6.1 Service mode 1 (Indication of a service mode 1 is nothing.)
Multiplex push timing chart (Example: Service mode 2)
[SOURCE] Key ON (Hold)
[EJECT] Key ON (Hold)
[MENU]
[PLAY / PAUSE]
[FOLDER UP]
Key ON
Key ON
Key ON
Within 0.5 seconds
Within 2 seconds
Within 2 seconds
Within 2 seconds
Shift to service Mode 2
Keep this state more 2 secondswhile continuing pressing the[STANDBY/ON ATTENUATOR] buttonand [EJECT] button sequentially.
Screen indication
NO EJECT? *–1 EMERGENCY EJECT? *–2
Exchanging it operate a menu of a service mode with the [ ] button and [ ] button. Operate choice of a menu with a [PLAY/PAUSE] button. *1 : When an [PLAY/PAUSE] button is pushed in NO EJECT indication, it is set by an EJECT prohibition mode. When an [PLAY/PAUSE] button is pushed in EJECT OK indication, it is set by a normal mode. *2 : Forced EJECT movement A screen becomes normal indication after an [PLAY/PAUSE] button was pushed.
(No.MA401<Rev.001>)1-25
4.6.2 Service mode 2
Set to service mode 2: [SOURCE] [EJECT] [MENU] [PLAY/PAUSE] [FOLDER UP]
Screen indication
SERVICE MODE 2 INITIALIZE ALL INITIALIZE INITIALIZE DVD INITIALIZE BT
Exchanging it operate a menu of a service mode with the [ ] button and [ ] button. Operate choice of a menu with a [PLAY/PAUSE] button.
INITIALIZE ALL
INITIALIZE
INITIALIZE DVD
INITIALIZE BT
NOW ... INITIALIZE ALL
NOW ... INITIALIZE
INITIALIZE DVD OK**
INITIALIZE ALL OK**
INITIALIZE OK**
INITIALIZE BT OK**
INITIALIZE ALL (Each EEPROM is initialized by a factory shipment state.) Main micon EEPROM initialization (user entry domain, error history, speaker setting, subarea of J-version, data to pre-set ) Panel micon EEPROM initialization (picture adjustment data) DVD unit EEPROM initialization (except a permanent domain) Bluetooth module EEPROM initialization After clear completion, a screen returns to normal indication after OK indication was displayed for three seconds.
INITIALIZE (Initialization of a user area of each EEPROM) Main micon EEPROM initialization
(a user entry domain ) (a user entry domain, speaker setting,
subarea of J-version, data to pre-set ) Panel micon EEPROM initialization
(picture adjustment data ) DVD unit EEPROM initialization
(except a permanent domain) After clear completion, a screen returns to
normal indication after OK indication was displayed for three seconds.
Full initialization of EEPROM of a DVD unit ( It is included a permanent domain) After clear completion, this indication is continued till an effective key is input.
Full initialization of EEPROM of Bluetooth After clear completion, this indication is continued till an effective key is input
1-26 (No.MA401<Rev.001>)
4.6.3 Service mode 3
Set to service mode 3: [SOURCE] [EJECT] [MENU] [PLAY/PAUSE] [DISP]
Screen indication
SERVICE MODE 3 SERVICE MODE INTIALIZE ALL RUNNNING MODE
Exchanging it operate a menu of a service mode with the [ ] button and [ ] button. Operate choice of a menu with a [PLAY/PAUSE] button.
SERVICE MODE
SERVICE MODE VERSION AREA/REGION TEMPERATURE MEMORY CHECK DVD NTSC/PAL DVD CHECK MODE
SERVICE MODE ERROR READ ERROR CLEAR BT VERSION
Exchanging it operate a menu of a service mode with the [ ] button and [ ] button.
Operate choice of a menu with a [PLAY/PAUSE] button.
Return to previous menu with a [BAND] button.
VERSION MAIN V**** [**]
DISC **** CH ****** PANEL V**** V*** [**] V***
Micon version indication Main micon version and ROM
correction version DVD module version CH version Panel micon version and ROM
correction version
AREA/REGION SYS-AREA : * DISC-AREA : ** REGION : *
Area and region indicattion Main micon area DVD area Region
TEMPERATURE Temperature data reading Temperature data by the temperature sensor in the main
micon and DVD-PCB is read every 5 seconds and displayed in hex numbers.
MEMORY CHECK ( It is displayed only at the time of the disc insertion ) Memory residual quantity indication mode Data residual quantity of a disc is displayed by LCD. About the playback control-related key ([FSKIP], [BSKIP], [UP], [DOWN], [VOL]), only movement is effective. Indication does not change as memory residual quantity indication. About cancellation of this mode, press the [STANDBY/ON ATTENUATOR] button.
DVD NTSC/PAL NTSC PAL
DVD picture change DVD module output picture setting (NTSC) DVD module output picture setting (PAL)
DVD CHECK MODE See "DVD CHECK MODE" for details.
(No.MA401<Rev.001>)1-27
ERROR READ DVD ERROR READ CH ERROR READ MECHA ERROR READ READ ALL
DVD ERROR READ Reading of a DVD unit error history
CH ERROR READ Reading of a CD changer error history
MECHA ERROR READ Reading of a door mechanism error history
READ ALL Reading of a main micon EEPROM (All contents)
Bluetooth version indication Software version of BT core Hardware version of BT Module Software version of BT Module BT Address
INITIALIZE ALL
NOW ... INITIALIZE ALL INITIALIZE ALL
OK***
INITIALIZE ALL (Each EEPROM is initialized by a factory shipme-
nt state.) Main micon EEPROM initiali- zation (user entry domain,error history,speaker setting, subarea of J-version, data to pre-set ) Panel micon EEPROM initiali - zation (picture adjustment data) DVD unit EEPROM initialization (except a permanent domain) Bluetooth module EEPROM initialization After clear completion, a screen returns to normal indication after OK indication wasdisplayed for three seconds.
RUNNING MODE See "Running mode" for details.
1-28 (No.MA401<Rev.001>)
4.6.4 Service mode 4
4.7 DVD Check Mode
Set to service mode 4: [SOURCE] [EJECT] [MENU] [PLAY/PAUSE] [REW]
Screen indication
SERVICE MODE 4 RDS S MODE MONITOR S MODE HD RADIO S MODE
Exchanging it operate s menu of a service mode with the [ ] buttonand [ ] button. Operate choice of a menu with a [PLAY/PAUSE] button.
RDS S MODE RDS service mode (Only RDS model)
MONITOR S MODE R/W CHROMA DATA CLEAR
*See "Monitor adjustment" for details. CHROMA DATA read/write of NTSC/PAL signal processing IC Clear of CHROMA DATA (return to an initial value)
DVD CHECK MODE NORMAL PLAY EF OUT-TRACKING OFF EF IN-TRACKING OFF CD-LASER ON DVD-LASER ON DVDx1 JITTER MODE
DVD CHECK MODE EEPROM DATA DISP EEPROM DATA CLEAR TEMPERATURE SEARCH & JITTER MONITOR PLAY
DVD CHECK MODE STOP OPEN CLOSE
Exchanging it operate a menu of a service mode with the [UP] buttonand [DOWN] button. Operate choice of a menu with a [PLAY/PAUSE] button.
Command Mechanism unit operation Indication contents
NORMAL PLAY Start at normal speed (After start, jitter is measured by an inner position.)
Laser current value, jitter value
EF OUT-TRACKING OFF Tracking off the outermost position of CD
Tracking off the outermost position of CD
For EF phase error
For EF phase errorEF IN-TRACKING OFF
CD-LASER ON
DVD-LASER ON
CD_LD lights and laser current is displayed.
DVD_LD lights and laser current is displayed.
Laser current value, jitter value
Laser current value, jitter value
Laser current value, jitter valueDVDx1 JITTER MODE DVD x1 jitter measuring mode (for use in mechanism adjustment)
EEPROM DATA DISP
EEPROM DATA CLEAR
Contents of EEPROM is displayed.
Contents of EEPROM is initialized.
EEPROM address EEPROM contents
EEPROM address EEPROM contents
TEMPERATURE Temperature indication Temperature is displayed in hex numbers.
Position measured with VT-501 jitter value.SEARCH & JITTER The search and jitter measurement to an appointed position of DVD.
MONITOR Monitor terminal setting
PLAY DVD x1 stopped start (After start, jitter is measured by an inner position.) Not displayed.
Not displayed.
Not displayed.
Not displayed.
STOP
OPEN OPEN
Disc stopped, LD-OFF
CLOSE CLOSE
(No.MA401<Rev.001>)1-29
4.8 Error code tables4.8.1 Mechanism error code
4.8.2 Disc error code
Detailed error code
Loading of a running modeDisc was pulled out in a wait.
Error contents Details Error code
Disc loading error ‡B D1 time out
Eject error ‡B B1 time out ‡C C1 time out
Error in loading wait
09 0013
00230024
003109
0101
Even if TOC reading passes after the end with CD running mode for 30 seconds, the first trackaccess is not finished.
Even if first track passes after the end with CD running mode for 30 seconds, the first trackaccess is not finished.
TOC read error TOC lead movement of a CD is not completed. 84
80
80
80
80
80
80
80
80
80
80
80
80
84
0059
0060
0061
0069
0070
0090
0091
0093
0094
0095
0071
0072
0074
0075
First track access error
Last track access error
T12 access error
T1 access error Even if T1 access passes in a DVD runnungmode for 30 seconds, it is not finished.
Even if T12 access passes in a DVD runnungmode for 30 seconds, it is not finished.
T24 access error Even if T24 access passes in a DVD runnungmode for 30 seconds, it is not finished.
DVD L1 layer adjustment error
DVD L0 layer adjustment error
Read-in area read error Read-in area read operation of DVD is notcompleted.
Adjustment of L1 layer of DVD is not finishhednormally. (including focus jump failure)
Adjustment of L0 layer of DVD is not finishhednormally. (including focus jump failure)
NO DISC judgment Judgment without disc
It is NO DISC by start failure Start is impossible
Stop in running mode playback
Logic format NG
Seek access error
Logic format analysis inability or non-correspondence logic format
It cannot arrive at an aim address even if it passes for 15 seconds.
1-30 (No.MA401<Rev.001>)
4.8.3 Error codes of panel mechanism
10 degrees
20 degrees
30 degrees
Openopen
OpenPanel1
1
1
1
Main Body
PANEL ANGLE
Open error 1. Time out error by OPEN position cannot detect.
DetailError code
(Service mode)
Close error (ANGLE 1 error) 1. Time out error by ANGLE 1 position cannot detect.
Angle positioning error Moving to 10 degrees (ANGLE 2 error) 1. Time out error by ANGLE 2 position cannot detect at moving to open position. 2. Missing to ANGLE 1 and detected ANGLE 2 position at moving to open position. 3. Time out error by ANGLE 2 cannot detect at moving close position.
Moving to 20 degrees (ANGLE 3 error) 1. Time out error by ANGLE 3 position cannot detect at moving to open position. 2. Missing to ANGLE 2 and detected ANGLE 3 position at moving to open position. 3. Time out error by ANGLE 3 cannot detect at moving close position.
Moving to 30 degrees (ANGLE 4 error) 1. Time out error by ANGLE 4 position cannot detect at moving to open position. 2. Missing to ANGLE 3 and detected ANGLE 4 position at moving to open position. 3. Time out error by ANGLE 4 cannot detect at moving close position.
Abnormal switch position at moving panel The Panel move to open and close position, detected abnormal switch position.
0A0001
0B0006
0D00210D00220D0023
0E00310E00320E0033
0F00410F00420F0043
0A0000
(No.MA401<Rev.001>)1-31
4.9 Running mode
* Cancellation of running1,2 : Press the [EJECT] key * In running 1,2 cancellation, a door does not stop at the position and moves to a panel position. * Cancellation of running3 to 8 : Press the [POWER] key * The number of count and an error cord are displayed in running.
Playback contents in a running mode• CD
The first track is played for 30 seconds.→The last track is played for 30 seconds. (The last track is played in the case of less than till the last for 30 seconds.)
• DVD2layer disc (Pit disc)Title 1 (the L0 layer internal circumference) is played for 30 seconds.→ Title 12 (L0 layer circumference) is played for 30 seconds.→ Title 24 (L1layer internal circumference) is played for 30 seconds.
2layer disc (Recordable disc)Title 1 (the L0 layer internal circumference) is played for 30 seconds.→ Title 13 (L0 layer circumference) is played for 30 seconds→Title 24 (L1layer internal circumference) is played for 30 seconds.
1layer disc First chapter of title 1 is played for 30 seconds. → The last chapter of title 1 is played for 30 seconds.
4.10 Monitor adjustment* When adjusting, switch on the main unit and insert a test disc (VT-501). And play the test disc and pause it.
(1) Set the service mode 4.(2) Exchanging it operate a menu of a service mode with the [UP] button and [DOWN] button.(3) Change data with the [B.SKIP]/[F.SKIP] buttons.(4) Write data with a [PLAY/PAUSE] button.
DVD+Door mecha running6
DVD+Door mecha running1
DVD+Door mecha running2
DVD+Door mecha running3
DVD+Door mecha running4
DVD+Door mecha running5
In Mecha error In disc error
RUNNING1 MECHA
RUNNING2 MECHA
RUNNING3 DVD
RUNNING4 DVD
RUNNING5 DVD
RUNNING6 DVD
RUNNING7 DVD
RUNNING8 DVD
Panel close Panel open Panel detach position Panel angle
3 position Panel angle 1 position Panel angle 2 position
RETRY
NO RETRY
Indication Explanation Operation contents of 1 cycle
Door mecha running 1
Door mecha running 2 Retly
Retly
Retly
Retly Retly
Retly
Stop
Stop
Stop
Stop
Stop
StopLoading Eject Wait for 5 seconds+Door open/close
Loading Eject Wait for 5 seconds+Door open/close
Panel close Panel open
Loading Playback Eject Wait for 5 seconds+Door open/close
Loading Playback Eject Wait for 5 seconds+Door open/close
Loading Playback Eject Wait for 5 seconds+Door open/close
Loading Playback Eject Wait for 5 seconds+Door open/close
Adjustment of the quantity of brightness outline core ring (NTSC)Adjustment of the quantity of brightness outline core ring (PAL)Adjustment of the brightness outline revision gain (NTSC)Adjustment of the brightness outline revision gain (PAL)Change in TINT of the whole picture (NTSC)Change in TINT of the whole picture (PAL)Change with the deepness of the color of the whole picture (NTSC)Change with the deepness of the color of the whole picture (PAL)Tint adjustment (NTSC)Tint adjustment (PAL)Color adjustment (NTSC)Color adjustment (PAL)Set the offset DC of the input video signal (NTSC)Set the offset DC of the input video signal (PAL)Quantity of transmission revision of the YUV DCQuantity of transmission revision of the YUV DCContrast adjustment between the black - white (NTSC)Contrast adjustment between the black - white (PAL)Conversion coefficients from YUV to RGB (PRCL)Conversion coefficients from YUV to RGB (PBCL)Conversion coefficients from YUV to RGB (YCL)Conversion coefficients from YUV to RGB (BCL)Conversion coefficients from YUV to RGB (RCL)Noise shaving (NTSC)Noise shaving (PAL)Black level adjustment (NTSC)Black level adjustment (PAL)Gain setting of Red signal (NTSC)Gain setting of Red signal (PAL)Gain setting of Green signal (NTSC)Gain setting of Green signal (PAL)Gain setting of Blue signal (NTSC)Gain setting of Blue signal (PAL)Set the cut-off of the Red signal (NTSC)Set the cut-off of the Red signal (PAL)Set the cut-off of the Green signal (NTSC)Set the cut-off of the Green signal (PAL)Set the cut-off of the Blue signal (NTSC)Set the cut-off of the Blue signal (PAL)ON/OFF change of the gamma revisionAdjust 1 gamma revision point position of a Red signalAdjust 2 gamma revision point position of a Red signalAdjust 3 gamma revision point position of a Red signalAdjust 4 gamma revision point position of a Red signalAdjust 5 gamma revision point position of a Red signalAdjust 6 gamma revision point position of a Red signalAdjust 7 gamma revision point position of a Red signalAppoint gamma revision gain 1 of the Red signalAppoint gamma revision gain 2 of the Red signalAppoint gamma revision gain 3 of the Red signalAppoint gamma revision gain 4 of the Red signalAppoint gamma revision gain 5 of the Red signalAppoint gamma revision gain 6 of the Red signalAppoint gamma revision gain 7 of the Red signalAppoint gamma revision gain 8 of the Red signalAdjust 1 gamma revision point position of a Green signalAdjust 2 gamma revision point position of a Green signalAdjust 3 gamma revision point position of a Green signalAdjust 4 gamma revision point position of a Green signalAdjust 5 gamma revision point position of a Green signalAdjust 6 gamma revision point position of a Green signalAdjust 7 gamma revision point position of a Green signalAppoint gamma revision gain 1 of the Green signal
Indication Minimum value Maximum value Initial value Reference register value
Appoint gamma revision gain 2 of the Green signalAppoint gamma revision gain 3 of the Green signalAppoint gamma revision gain 4 of the Green signalAppoint gamma revision gain 5 of the Green signalAppoint gamma revision gain 6 of the Green signalAppoint gamma revision gain 7 of the Green signalAppoint gamma revision gain 8 of the Green signalAdjust 1 gamma revision point position of a Blue signalAdjust 2 gamma revision point position of a Blue signalAdjust 3 gamma revision point position of a Blue signalAdjust 4 gamma revision point position of a Blue signalAdjust 5 gamma revision point position of a Blue signalAdjust 6 gamma revision point position of a Blue signalAdjust 7 gamma revision point position of a Blue signalAppoint gamma revision gain 1 of the Blue signalAppoint gamma revision gain 2 of the Blue signalAppoint gamma revision gain 3 of the Blue signalAppoint gamma revision gain 4 of the Blue signalAppoint gamma revision gain 5 of the Blue signalAppoint gamma revision gain 6 of the Blue signalAppoint gamma revision gain 7 of the Blue signalAppoint gamma revision gain 8 of the Blue signalAdjust the horizontal indication point of the picture (NTSC)Adjust the horizontal indication point of the picture (PAL)Adjust the vertical indication point of the picture (NTSC)Adjust the vertical indication point of the picture (PAL)AD clock gain adjustment (NTSC)AD clock gain adjustment (PAL)Noise reduction of the Y signal (NTSC)Noise reduction of the Y signal (PAL)Choose a YC separation filter (NTSC)Choose a YC separation filter (PAL)Color pulling out filter setting (NTSC)Color pulling out filter setting (PAL)Choose com movement mode and color BPF (NTSC)Choose com movement mode and color BPF (PAL)Vertical dot cancellation setting (NTSC)Vertical dot cancellation setting (PAL)Noise reduction setting (NTSC)Noise reduction setting (PAL)Quantity of brightness adjustment setting (NTSC)Quantity of brightness adjustment setting (PAL)Brightness gain adjustment (NTSC)Brightness gain adjustment (PAL)Color signal output level setting (NTSC)Color signal output level setting (PAL)ACC movement mode settingC signal filter characteristic setting of the Y/C separation part (NTSC)C signal filter characteristic setting of the Y/C separation part (PAL)Amplitude killer off level settingAmplitude killer on level settingClamp DC level adjustment settingClamp speed adjustment settingNoise filter band setting of horizontal synchronization signal and vertical synchronizing signal (NTSC)Noise filter band setting of horizontal synchronization signal and vertical synchronizing signal (PAL)Horizontal phase comparison gain setting (NTSC)Horizontal phase comparison gain setting (PAL)Horizontal loop filter setting 1Horizontal loop filter setting 2Horizontal loop filter setting 3Synchronization separation burst clock setting (NTSC)
Indication Minimum value Maximum value Initial value Reference register value
Synchronization separation burst clock setting (PAL)Free run center value setting of horizontal synchronization signal (NTSC)Free run center value setting of horizontal synchronization signal (PAL)DOKIDET 01DOKIDET 02DOKIDET 03UnusedUnusedSubcareer center frequency setting (NTSC)UnusedSubcareer center frequency setting (PAL)UnusedCoordinate the delay of the C signal with a Y signal (NTSC)Coordinate the delay of the C signal with a Y signal (PAL)Coordinate the VCOM amplitude of the LCD (NTSC)Coordinate the VCOM amplitude of the LCD (PAL)Coordinate VCOM center value of the LCD (NTSC)Coordinate VCOM center value of the LCD (PAL)Set a variable range of the indication VSYNC frequency (NTSC)Set a variable range of the indication VSYNC frequency (PAL)Set time when indication VSYNC frequency changes (NTSC)Set time when indication VSYNC frequency changes (PAL)CLAMP MODE (NTSC)CLAMP MODE (PAL)
Indication Minimum value Maximum value Initial value Reference register value
Victor Company of Japan, LimitedMobile Entertainment Business Group Mobile Entertainment Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
PARTS LIST
* All printed circuit boards and its assemblies are not available as service parts.
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
DVD mechanism assembly and parts list (Block No.MJ)
Electrical parts list (Block No.01~04)
Packing materials and accessories parts list (Block No.M3)
Q101 2SD2114K/VW/-X TRANSISTORQ151 2SD2114K/VW/-X TRANSISTORQ161 2SD2114K/VW/-X TRANSISTORQ201 2SD2114K/VW/-X TRANSISTORQ251 2SD2114K/VW/-X TRANSISTORQ261 2SD2114K/VW/-X TRANSISTORQ341 2SD2704K-X TRANSISTORQ342 2SD2114K/VW/-X TRANSISTORQ350 ISA1530AC1/QR/X TRANSISTORQ350 or 2SB709A/QR/-X TRANSISTORQ351 ISA1530AC1/QR/X TRANSISTORQ351 or 2SB709A/QR/-X TRANSISTORQ371 RT1N441C-X TRANSISTORQ371 or UN2213-X DIGI TRANSISTORQ372 RT1P441C-X DIGI TRANSISTORQ372 or UN2113-X TRANSISTORQ373 RT1N441C-X TRANSISTORQ373 or UN2213-X DIGI TRANSISTORQ374 2SC3928A/QR/-X TRANSISTORQ374 or 2SD601A/QR/-X TRANSISTORQ701 RT1N141C-X DIGI TRANSISTORQ701 or DTC114EKA-X DIGI TRANSISTORQ806 RT1N441C-X TRANSISTORQ806 or UN2213-X DIGI TRANSISTORQ807 RT1P441C-X DIGI TRANSISTORQ807 or UN2113-X TRANSISTOR
Q842 RT1P141C-X DIGI TRANSISTORQ842 or DTA114EKA-X DIGI TRANSISTORQ843 RT1P141C-X DIGI TRANSISTORQ843 or DTA114EKA-X DIGI TRANSISTORQ844 RT1P141C-X DIGI TRANSISTORQ844 or DTA114EKA-X DIGI TRANSISTORQ845 RT1N141C-X DIGI TRANSISTORQ845 or DTC114EKA-X DIGI TRANSISTORQ847 2SC3928A/QR/-X TRANSISTORQ847 or 2SD601A/QR/-X TRANSISTORQ848 RT1N141C-X DIGI TRANSISTORQ848 or DTC114EKA-X DIGI TRANSISTORQ849 RT1N141C-X DIGI TRANSISTORQ849 or DTC114EKA-X DIGI TRANSISTORQ861 RSQ030P03-W MOS FETQ862 RT1P141C-X DIGI TRANSISTORQ862 or DTA114EKA-X DIGI TRANSISTORQ863 RT1P141C-X DIGI TRANSISTORQ863 or DTA114EKA-X DIGI TRANSISTORQ864 RT1P141C-X DIGI TRANSISTORQ864 or DTA114EKA-X DIGI TRANSISTORQ865 RT1N441C-X TRANSISTORQ865 or UN2213-X DIGI TRANSISTORQ881 RT1N141C-X DIGI TRANSISTORQ881 or DTC114EKA-X DIGI TRANSISTORQ951 RT1N141C-X DIGI TRANSISTORQ951 or DTC114EKA-X DIGI TRANSISTORQ952 ISA1530AC1/QR/X TRANSISTORQ952 or 2SB709A/QR/-X TRANSISTORQ953 RT1N441C-X TRANSISTORQ953 or UN2213-X DIGI TRANSISTORQ955 2SC3928A/QR/-X TRANSISTORQ955 or 2SD601A/QR/-X TRANSISTORQ8001 RT1N441C-X TRANSISTORQ8001 or UN2213-X DIGI TRANSISTORQ8003 RT1P141C-X DIGI TRANSISTORQ8003 or DTA114EKA-X DIGI TRANSISTORQ8004 RT1N441C-X TRANSISTORQ8004 or UN2213-X DIGI TRANSISTORQ8005 RT1N441C-X TRANSISTORQ8005 or UN2213-X DIGI TRANSISTORQ8006 RT1N441C-X TRANSISTORQ8006 or UN2213-X DIGI TRANSISTORQ8007 RT1N441C-X TRANSISTORQ8007 or UN2213-X DIGI TRANSISTORQ8011 RSQ030P03-W MOS FETQ8012 2SC3928A/QR/-X TRANSISTORQ8012 or 2SD601A/QR/-X TRANSISTORQ8013 ISA1530AC1/QR/X TRANSISTORQ8013 or 2SB709A/QR/-X TRANSISTORQ8021 RSQ030P03-W MOS FETQ8022 2SC3928A/QR/-X TRANSISTORQ8022 or 2SD601A/QR/-X TRANSISTORQ8023 ISA1530AC1/QR/X TRANSISTORQ8023 or 2SB709A/QR/-X TRANSISTORQ8041 RTQ035N03-W MOS FETQ8042 ISA1530AC1/QR/X TRANSISTORQ8042 or 2SB709A/QR/-X TRANSISTORQ8043 2SC3928A/QR/-X TRANSISTORQ8043 or 2SD601A/QR/-X TRANSISTORQ8051 RSQ030P03-W MOS FETQ8052 2SC3928A/QR/-X TRANSISTORQ8052 or 2SD601A/QR/-X TRANSISTORQ8053 ISA1530AC1/QR/X TRANSISTORQ8053 or 2SB709A/QR/-X TRANSISTORQ8083 RSQ030P03-W MOS FETQ8084 RT1N441C-X TRANSISTORQ8084 or UN2213-X DIGI TRANSISTORQ8091 RT1N141C-X DIGI TRANSISTORQ8091 or DTC114EKA-X DIGI TRANSISTORQ8092 RT1N141C-X DIGI TRANSISTORQ8092 or DTC114EKA-X DIGI TRANSISTORQ8093 RT1N141C-X DIGI TRANSISTORQ8093 or DTC114EKA-X DIGI TRANSISTORQ8094 MTM98140-X TRANSISTORQ8095 RT1N441C-X TRANSISTOR
Symbol No. Part No. Part Name Description Local
3-8
Q8095 or UN2213-X DIGI TRANSISTORQ8096 RT1N141C-X DIGI TRANSISTORQ8096 or DTC114EKA-X DIGI TRANSISTORQ8097 RT1P141C-X DIGI TRANSISTORQ8097 or DTA114EKA-X DIGI TRANSISTORQ8098 RT1P141C-X DIGI TRANSISTORQ8098 or DTA114EKA-X DIGI TRANSISTOR
D11 MA111-X SI DIODED11 or 1SS355W-X DIODED12 MA111-X SI DIODED12 or 1SS355W-X DIODED141 MA111-X SI DIODED141 or 1SS355W-X DIODED142 MA111-X SI DIODED142 or 1SS355W-X DIODED151 MC2836-X DIODED151 or MA152WA-X DIODED190 MA111-X SI DIODED190 or 1SS355W-X DIODED191 MA111-X SI DIODED191 or 1SS355W-X DIODED251 MC2836-X DIODED251 or MA152WA-X DIODED301 MC2836-X DIODED301 or MA152WA-X DIODED340 MA111-X SI DIODED340 or 1SS355W-X DIODED342 MA111-X SI DIODED342 or 1SS355W-X DIODED371 MA8110/M/-X Z DIODED371 or UDZW11B-X Z DIODED372 MA111-X SI DIODED372 or 1SS355W-X DIODED731 MA111-X SI DIODED731 or 1SS355W-X DIODED807 MA2SD31-X SB DIODED808 MA2SD31-X SB DIODED811 MA111-X SI DIODED811 or 1SS355W-X DIODED841 MA8110/M/-X Z DIODED841 or UDZW11B-X Z DIODED844 MC2838-X DIODED844 or MA152WK-X SI DIODED845 MA111-X SI DIODED845 or 1SS355W-X DIODED846 MC2836-X DIODED846 or MA152WA-X DIODED847 MA111-X SI DIODED847 or 1SS355W-X DIODED851 MA8180/M/-X Z DIODED851 or UDZW18B-X Z DIODED861 MA22D23-X SB DIODED871 MA8062/M/-X Z DIODE ADV4
D871 or UDZW6.2B-X Z DIODE ADV49J,AVX44J,AVX44C,AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
D881 MA8039-X Z DIODED881 or UDZW3.9B-X Z DIODED901 1N5401-F64 SI DIODED921 RR264M-400-X SI DIODED922 RR264M-400-X SI DIODED931 MA8062/M/-X Z DIODED931 or UDZW6.2B-X Z DIODED932 MA8062/M/-X Z DIODED932 or UDZW6.2B-X Z DIODED933 MA8062/M/-X Z DIODED933 or UDZW6.2B-X Z DIODED934 MA8062/M/-X Z DIODED934 or UDZW6.2B-X Z DIODED961 MA8062/M/-X Z DIODED961 or UDZW6.2B-X Z DIODED962 MA8062/M/-X Z DIODED962 or UDZW6.2B-X Z DIODED963 MA8062/M/-X Z DIODED963 or UDZW6.2B-X Z DIODED964 MA8062/M/-X Z DIODED964 or UDZW6.2B-X Z DIODED965 MA8062/M/-X Z DIODED965 or UDZW6.2B-X Z DIODED966 MA8062/M/-X Z DIODED966 or UDZW6.2B-X Z DIODED967 MA8062/M/-X Z DIODED967 or UDZW6.2B-X Z DIODED968 MA8062/M/-X Z DIODED968 or UDZW6.2B-X Z DIODED969 MA8062/M/-X Z DIODED969 or UDZW6.2B-X Z DIODED970 MA8062/M/-X Z DIODED970 or UDZW6.2B-X Z DIODED971 MA8062/M/-X Z DIODED971 or UDZW6.2B-X Z DIODED973 MA8062/M/-X Z DIODED973 UDZW6.2B-X Z DIODED981 MA22D23-X SB DIODED982 MA22D23-X SB DIODE ADV4
D8061 MA2SD31-X SB DIODED8062 MA2SD31-X SB DIODED8063 MA8180/M/-X Z DIODED8063 or UDZW18B-X Z DIODED8065 MA111-X SI DIODED8065 or 1SS355W-X DIODED8066 MA111-X SI DIODED8066 or 1SS355W-X DIODED8067 MA8062/M/-X Z DIODED8067 or UDZW6.2B-X Z DIODED8068 MA8062/M/-X Z DIODED8068 or UDZW6.2B-X Z DIODED8069 MA8062/M/-X Z DIODED8069 or UDZW6.2B-X Z DIODED8075 MA111-X SI DIODED8075 or 1SS355W-X DIODED9002 MA8056/M/-X Z DIODED9002 or UDZW5.6B-X Z DIODED9003 MA8056/M/-X Z DIODED9003 or UDZW5.6B-X Z DIODE
C5 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V MC7 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V MC8 NDC31HJ-220X C CAPACITOR 22pF 50V JC9 NCB31AK-224X C CAPACITOR 0.22uF 10V KC10 NCB31HK-103X C CAPACITOR 0.01uF 50V KC12 NCB31HK-103X C CAPACITOR 0.01uF 50V KC13 NCB31CK-104X C CAPACITOR 0.1uF 16V KC14 NCB31HK-103X C CAPACITOR 0.01uF 50V KC16 NCB31HK-103X C CAPACITOR 0.01uF 50V KC17 QEKJ1CM-107Z E CAPACITOR 100uF 16V MC18 NCB31CK-104X C CAPACITOR 0.1uF 16V KC19 NCB21AK-105X C CAPACITOR 1uF 10V KC20 NDC31HJ-6R0X C CAPACITOR 6pF 50V JC21 NCB31CK-104X C CAPACITOR 0.1uF 16V KC22 NCB31HK-102X C CAPACITOR 1000pF 50V KC23 NDC31HJ-180X C CAPACITOR 18pF 50V JC24 NCB31AK-224X C CAPACITOR 0.22uF 10V KC25 NCB31HK-103X C CAPACITOR 0.01uF 50V KC26 NCB21AK-105X C CAPACITOR 1uF 10V KC27 NDC31HJ-150X C CAPACITOR 15pF 50V JC29 NCB31CK-104X C CAPACITOR 0.1uF 16V KC30 NCB31HK-103X C CAPACITOR 0.01uF 50V KC31 NCB31HK-103X C CAPACITOR 0.01uF 50V K AVX4
4E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C32 QEKJ1CM-226Z E CAPACITOR 22uF 16V M AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C33 NDC31HJ-330X C CAPACITOR 33pF 50V J AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
Symbol No. Part No. Part Name Description Local
C34 NDC31HJ-330X C CAPACITOR 33pF 50V J AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C35 NDC31HJ-561X C CAPACITOR 560pF 50V J AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C36 NCB31HK-103X C CAPACITOR 0.01uF 50V K AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C37 NCB20JK-106X C CAPACITOR 10uF 6.3V K AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C38 NDC31HJ-331X C CAPACITOR 330pF 50V J AVX44E,AVX44EU,AVX44EE,AVX22E,AVX22EU,AVX22EE
C41 QEKJ1CM-107Z E CAPACITOR 100uF 16V MC42 NCB31HK-102X C CAPACITOR 1000pF 50V KC45 NDC31HJ-100X C CAPACITOR 10pF 50V JC46 NDC31HJ-2R0X C CAPACITOR 2pF 50V JC106 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V MC108 NDC31HJ-101X C CAPACITOR 100pF 50V JC113 NDC31HJ-821X C CAPACITOR 820pF 50V JC115 NDC31HJ-101X C CAPACITOR 100pF 50V JC121 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V MC122 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V MC124 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V MC125 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V M ADV4
Q471 ISA1530AC1/QR/X TRANSISTORQ471 or 2SB709A/QR/-X TRANSISTORQ530 2SC3928A/QR/-X TRANSISTORQ530 or 2SD601A/QR/-X TRANSISTORQ561 RT1N141C-X DIGI TRANSISTORQ561 or DTC114EKA-X DIGI TRANSISTORQ562 RT1P141C-X DIGI TRANSISTORQ562 or DTA114EKA-X DIGI TRANSISTORQ563 2SC3928A/QR/-X TRANSISTORQ563 or 2SD601A/QR/-X TRANSISTORQ601 INK0002AU1-X MOS FETQ601 or 2SK3019-X MOS FETQ602 INK0002AU1-X MOS FETQ602 or 2SK3019-X MOS FETQ650 RT1N141C-X DIGI TRANSISTORQ650 or DTC114EKA-X DIGI TRANSISTORQ651 RT1P141C-X DIGI TRANSISTORQ651 or DTA114EKA-X DIGI TRANSISTORQ652 RT1N141C-X DIGI TRANSISTORQ652 or DTC114EKA-X DIGI TRANSISTORQ653 RT1P141C-X DIGI TRANSISTORQ653 or DTA114EKA-X DIGI TRANSISTORQ654 RT1N141C-X DIGI TRANSISTORQ654 or DTC114EKA-X DIGI TRANSISTORQ655 RT1P141C-X DIGI TRANSISTORQ655 or DTA114EKA-X DIGI TRANSISTORQ656 RT1P141C-X DIGI TRANSISTORQ656 or DTA114EKA-X DIGI TRANSISTORQ657 RT1P141C-X DIGI TRANSISTORQ657 or DTA114EKA-X DIGI TRANSISTOR
D530 MA8056/M/-X Z DIODED530 or UDZW5.6B-X Z DIODED531 MA8091/M/-X Z DIODED531 or UDZW9.1B-X Z DIODED561 MA111-X SI DIODED563 MA111-X SI DIODED565 MA111-X SI DIODED566 MA2SD32-X DIODED567 MA2SD31-X SB DIODED568 MA111-X SI DIODED650 MC2838-X DIODED650 or MA152WK-X SI DIODED651 NECWB205/B2/-X LED
C401 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC402 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC403 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC404 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC405 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC406 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC407 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC408 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC409 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC410 NCBA1AK-104W C CAPACITOR 0.1uF 10V K
Symbol No. Part No. Part Name Description Local
C411 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC412 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC413 NCB20JK-106X C CAPACITOR 10uF 6.3V KC414 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC415 NCB20JK-106X C CAPACITOR 10uF 6.3V KC416 NCB20JK-106X C CAPACITOR 10uF 6.3V KC417 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC418 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC419 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC420 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC421 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC423 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC424 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC425 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC426 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC427 NCB20JK-106X C CAPACITOR 10uF 6.3V KC428 NDC31HJ-330X C CAPACITOR 33pF 50V JC429 NDC31HJ-121X C CAPACITOR 120pF 50V JC430 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC431 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC432 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC433 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC434 NDCA1HJ-100W C CAPACITOR 10pF 50V JC435 NDCA1HJ-100W C CAPACITOR 10pF 50V JC436 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC437 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC438 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC439 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC440 NDC31HJ-680X C CAPACITOR 68pF 50V JC441 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC442 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC443 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC444 NDCA1HJ-100W C CAPACITOR 10pF 50V JC445 NDCA1HJ-100W C CAPACITOR 10pF 50V JC446 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC450 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC451 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC452 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC453 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC454 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC455 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC456 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC457 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC459 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC471 NDCA1HJ-100W C CAPACITOR 10pF 50V JC474 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC501 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC502 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC503 NCB20JK-106X C CAPACITOR 10uF 6.3V KC505 NCB20JK-106X C CAPACITOR 10uF 6.3V KC506 NCBA1EK-472W C CAPACITOR 4700pF 25V KC508 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC509 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC510 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC511 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC514 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC516 NCB20JK-106X C CAPACITOR 10uF 6.3V KC517 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC518 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC521 NDC31HJ-390X C CAPACITOR 39pF 50V JC522 NDC31HJ-390X C CAPACITOR 39pF 50V JC523 NDC31HJ-390X C CAPACITOR 39pF 50V JC532 NCBA1HK-102W C CAPACITOR 1000pF 50V KC533 NCBA1CK-103W C CAPACITOR 0.01uF 16V KC535 NCB30JK-105X C CAPACITOR 1uF 6.3V KC537 NCB11AK-106X C CAPACITOR 10uF 10V KC538 NCB11AK-106X C CAPACITOR 10uF 10V KC543 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC544 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC546 NCB20JK-106X C CAPACITOR 10uF 6.3V KC547 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC548 NCB20JM-475X C CAPACITOR 4.7uF 6.3V MC549 NCB20JK-155X C CAPACITOR 1.5uF 6.3V KC550 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC551 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC552 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC553 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC554 NCBA1AK-104W C CAPACITOR 0.1uF 10V K
Symbol No. Part No. Part Name Description Local
3-22
C555 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC556 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC557 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC558 NCBA1EK-682W C CAPACITOR 6800pF 25V KC559 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC560 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC561 NBE20JM-226X TA E CAPACITOR 22uF 6.3V MC562 NCB21AK-225X C CAPACITOR 2.2uF 10V KC563 NCB30JK-105X C CAPACITOR 1uF 6.3V KC564 NCB20JM-475X C CAPACITOR 4.7uF 6.3V MC565 NCBA1AK-473W C CAPACITOR 0.047uF 10V KC567 NCB30JK-105X C CAPACITOR 1uF 6.3V KC590 NCB20JK-106X C CAPACITOR 10uF 6.3V KC601 NCBA1AK-473W C CAPACITOR 0.047uF 10V KC602 NCBA1AK-104W C CAPACITOR 0.1uF 10V KC603 NBE21AM-226X TA E CAPACITOR 22uF 10V MC604 NCB20JK-106X C CAPACITOR 10uF 6.3V KC605 NCBA1CK-103W C CAPACITOR 0.01uF 16V K
D5001 MA8056/M/-X Z DIODED5001 or UDZW5.6B-X Z DIODED5002 MA8056/M/-X Z DIODED5002 or UDZW5.6B-X Z DIODED5003 MA8056/M/-X Z DIODED5003 or UDZW5.6B-X Z DIODED5004 MA8056/M/-X Z DIODED5004 or UDZW5.6B-X Z DIODED5005 MA8056/M/-X Z DIODED5005 or UDZW5.6B-X Z DIODED5006 MA8056/M/-X Z DIODED5006 or UDZW5.6B-X Z DIODED5007 MA8056/M/-X Z DIODED5007 or UDZW5.6B-X Z DIODED5008 MA8200-X Z DIODED5008 or UDZW20B-X Z DIODED5010 MA8056/M/-X Z DIODED5010 or UDZW5.6B-X Z DIODED5011 MA8056/M/-X Z DIODED5011 or UDZW5.6B-X Z DIODED5012 MA8056/M/-X Z DIODED5012 or UDZW5.6B-X Z DIODED5013 MA8056/M/-X Z DIODED5013 or UDZW5.6B-X Z DIODED5014 MA8056/M/-X Z DIODED5014 or UDZW5.6B-X Z DIODED5015 MA8056/M/-X Z DIODED5015 or UDZW5.6B-X Z DIODED5016 MA8056/M/-X Z DIODED5016 or UDZW5.6B-X Z DIODED5017 MA8056/M/-X Z DIODED5017 or UDZW5.6B-X Z DIODED5018 MA8056/M/-X Z DIODED5018 or UDZW5.6B-X Z DIODED5019 MA8056/M/-X Z DIODED5019 or UDZW5.6B-X Z DIODED5020 MA8056/M/-X Z DIODED5020 or UDZW5.6B-X Z DIODE
Packing materials and accessories parts listBlock No. M MM3
No additional / supplemental order of WARRANTY CARDs are available
The parts without symbol number are not service.
P4
P4
P4 P4
P4
A7
A11
A12
P4
P4
A7
A2
Only J
Only
AVX44C
A1,A3
A5,A6
A8 Only
ADV49J
AVX44J,C
AVX44A,UT
Only
AVX44E,EU
A1,A3
A4,A5
A6,A7
A8,A10
A27
Only
AVX22E,EU
A1,A3
A4,A6
A7,A8
A27
Only
AVX44U
A1,A3
A4,A5
A6,A8
P4
Only
AVX44EE
A1,A3
A5,A6
A7,A8
Only
AVX22E,EU
AVX44E,EU,U
A22
A21
P4
Only
AVX22EE
A1,A3
A6,A7
A8
P1
P7
P6
P2
P3
P10
P8
P9
KIT : A13,A14
A15,A16,A17,A18
A19
A26
A24
A23
A25
A20
3-28
Packing and AccessoriesBlock No. [M][3][M][M]
Symbol No. Part No. Part Name Description Local
A 1 LVT1797-001A INST BOOK ENG SPA FRE ADV49J,AVX44J,AVX44CA 1 LVT1797-003A INST BOOK ENG GER FRE DUT AVX44EA 1 LVT1797-005A INST BOOK ENG SPA FRE AVX44EUA 1 LVT1797-007A INST BOOK ENG RUS UKR AVX44EEA 1 LVT1798-002A INST BOOK ENG CHI(TAIWAN) THA AVX44UA 1 LVT1798-004A INST BOOK ENG CHI(TAIWAN) AVX44UTA 1 LVT1798-001A INST BOOK ENG AVX44AA 1 LVT1800-001A INST BOOK ENG GER FRE DUT AVX22EA 1 LVT1800-003A INST BOOK ENG SPA FRE AVX22EUA 1 LVT1800-005A INST BOOK ENG RS UKR AVX22EEA 2 LVT1797-004A INST BOOK SPA ITA POR SWE AVX44EA 2 LVT1797-006A INST BOOK TUR RUS PER AVX44EUA 2 LVT1798-003A INST BOOK KOR ARA PER AX44UA 2 LVT1800-002A INST BOOK SPA ITA POR SWE AVX22EA 2 LVT1800-004A INST BOOK TUR RUS PER AVX22EUA 3 LVT1797-002A INSTALL MANUAL ENG SPA FRE AXV49J,AVX44J,AVX44CA 3 LVT1797-008A INSTALL MANUAL ENG GER FRE DUT AVX44E,AVX22EA 3 LVT1797-010A INSTALL MANUAL ENG SPA FRE AVX44EU,AVX22EUA 3 LVT1797-012A INSTALL MANUAL ENG RUS UKR AVX44EE,AVX22EEA 3 LVT1798-006A INSTALL MANUAL ENG CHI(TAIWAN) THA AVVX44U,AVX44UTA 3 LVT1798-005A INSTALL MANUAL ENG AVX44AA 4 LVT1797-009A INSTALL MANUAL SPA ITA POR SWE AVX44E,AVX22EA 4 LVT1797-011A INSTALL MANUAL TUR RUS PER AVX44EU,AVX22EUA 4 LVT1798-007A INSTALL MANUAL KOR ARA PER AVX44UA 5 LVT1672-001A INST SHEET ADV49J,AVX44J,AVX44C,AVX44E,AVX44
EU,AVX44U,AVX22E,AVX22EUP 4 FSPG4002-001 POLY BAG AVX44EE,AVX44UT,AVX44A,AVX22EEP 6 QPA00801205 POLY BAG 8cm x 12cmP 7 QPA01003003 POLY BAG 10cm x 30cmP 8 QPC03004315PB POLY BAG 30cm x 43cmP 9 QPA01002203 POLY BAG 10cm x 22cmP 10 LV22311-002A CUSHION(M)
3-29
Contents
Block diagram
Standard schematic diagrams
Printed circuit boards
2-1
2-2
2-8 to 10
CD-ROM No.SML200803
SCHEMATIC DIAGRAMSDVD/CD RECEIVER
No.MA401SCH<Rev.001>
2008/3
KD-ADV49J,KD-AVX44J,KD-AVX44C
KD-AVX44E, KD-AVX44EU,KD-AVX44EE
KD-AVX44U,KD-AVX44UT,KD-AVX44A
KD-AVX22E,KD-AVX22EU,KD-AVX22EE
COPYRIGHT 2008 Victor Company of Japan, Limited.
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)