1 Back to Main Page Julie - Universal Car Emulator Programs: Mercedes CR2 with CAN WSP.........................................................................................3 Program Use Mercedes CR2 with CAN WSP • Sprinter 2.2 CDi and 2.7 Cdi • ML 2.7 CDi 5-socket – automatic start • Also suitable for 2.7 and 3.2 with electronic ignition switch – automatic start You can buy our products and obtain technical support from our distributor. Find a distributor near you by clicking on the link: www.carlabimmo.com/our-partners
6
Embed
Julie - Universal Car Emulator Programs€¦ · Back to Main Page Mercedes CR2 with CAN WSP In Universal Julie Emulator solder jumpers J1, J3 and J4 USE Sprinter 2.2 CDi and 2.7 CDi
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
Back to Main Page
Julie - Universal Car Emulator Programs:Mercedes CR2 with CAN WSP.........................................................................................3
Program Use
Mercedes CR2 with CAN WSP
• Sprinter 2.2 CDi and 2.7 Cdi• ML 2.7 CDi 5-socket – automatic start• Also suitable for 2.7 and 3.2 with electronic
ignition switch – automatic start
You can buy our products and obtain technical support from our distributor. Find a distributornear you by clicking on the link: www.carlabimmo.com/our-partners
- no jumpers – diagnostic mode - it flashes every second
- adjusting to the ECU – flashing 0,1 sec
- after adjusting it lights constantly and blinks every other second
You can buy our products and obtain technical support from our distributor. Find a distributornear you by clicking on the link: www.carlabimmo.com/our-partners
Also suitable for 2.7 and 3.2 with electronic ignition switch – automatic start
If you are installing the CR2 emulator in a car with automatic transmission, solder 120 Ohmjumper on the emulator and insert a 120 Ohm resistor between CAN lines.
You can buy our products and obtain technical support from our distributor. Find a distributornear you by clicking on the link: www.carlabimmo.com/our-partners
When the emulator is connected,disconnect CAN from original immo!
Connecting the emulator to the ECU
Find 5P08C3 memory
You can buy our products and obtain technical support from our distributor. Find a distributornear you by clicking on the link: www.carlabimmo.com/our-partners
In the addresses from1D0 to 1D4 write 02 02 00 FF FF values
that will start the car automatically
If you have an electronic ignition switch,the following changes should be made to 5P08C3 memory
In address 131 write 12 value and from 1D0 to 1D4write 02 02 00 FF FF values
You can buy our products and obtain technical support from our distributor. Find a distributornear you by clicking on the link: www.carlabimmo.com/our-partners
Due to possible construction changes of cars, check signals with multimeter in the ECU plug.
All rights reserved.Unauthorized copying, hiring, lending, public performance will be punished!
We state that we are the only authentic authors of this manual. We possess copyright of thispublication. Any trials of unauthorized copying, hiring, quoting prohibited!!! Both service and
advertisement constitute copyright and they are the subject to the protection in accordance with theAct from 4th Feb. 1994 on Copyright and Related Laws (Statute Book no. 24 position 93) and
protection on the basis of the Act from 8th June 1993 on combating an unfair competition (StatuteBook no. 47 position 211)
www.carlabimmo.com
Last updated 29.01.2018
You can buy our products and obtain technical support from our distributor. Find a distributornear you by clicking on the link: www.carlabimmo.com/our-partners