www.norgren.com/info/US-ACT-72 ACT-72 ACTUATORS ISO/VDMA Cylinders DA/8000 Double acting Ø 32 ... 320 mm Conforms to ISO 6431, VDMA 24562 and NFE 49-003-1 High performance, ruggedness and reliability Extensive range of mountings Technical data Medium: Compressed air, filtered, lubricated or non-lubricated Standard: ISO 6431, VDMA 24562, NFE 49-003-1 and corresponding BS Operation: RA/8000 double acting, adjustable cushioning RA/8000/M double acting, magnetic piston, adjustable cushioning Operating pressure: 15 to 232 psig (1 to 16 bar) 15 to 145 psig [1 to 10 bar] for Ø 250 and 320 mm Operating temperature: -4°F to +176°F (-20°C to +80°C ) max. Consult our Technical Service for use below +35°F (+2°C) Strokes: Standard, see table Non-standard strokes up to 3000 mm maximum Materials Barrel: anodized aluminum End covers: pressure diecast aluminium (Ø 200 to 320 mm gravity cast aluminum) Piston rod: stainless steel (Martensitic) Piston rod seals: polyurethane (Ø 125 to 320 mm nitrile rubber) Piston seals: polyurethane (Ø 125 to 320 mm nitrile rubber) ‘O’-rings: nitrile rubber Options selector ˙DC / 8050 / M˙ / ˙˙˙˙ Note: If option is not required, disregard option position within part number eg. RA/8100/100 For combinations of cylinder variants consult our Technical Service. * N1 and N2 option built using non chrome plate, stainless steel piston rods Piston ISO Port Model Model NPT Port Model Model Service Ø rod Ø size non-magnetic magnetic size non-magnetic magnetic kit 32 12 G1/8 DA/8032/* DA/8032/M/* 1/8" DC/8032/* DC/8032/M/* QA/8032/00 40 16 G1/4 DA/8040/* DA/8040/M/* 1/4" DC/8040/* DC/8040/M/* QA/8040/00 50 20 G1/4 DA/8050/* DA/8050/M/* 1/4" DC/8050/* DC/8050/M/* QA/8050/00 63 20 G3/8 DA/8063/* DA/8063/M/* 3/8" DC/8063/* DC/8063/M/* QA/8063/00 80 25 G3/8 DA/8080/* DA/8080/M/* 3/8" DC/8080/* DC/8080/M/* QA/8080/00 100 25 G1/2 DA/8100/* DA/8100/M/* 1/2" DC/8100/* DC/8100/M/* QA/8100/00 125 32 G1/2 DA/8125/* DA/8125/M/* 1/2" DC/8125/* DC/8125/M/* QA/8125/00 160 40 G3/4 DA/8160/* DA/8160/M/* 3/4" DC/8160/* DC/8160/M/* QA/8160/00 200 40 G3/4 DA/8200/* DA/8200/M/* 3/4" DC/8200/* DC/8200/M/* QA/8200/00 250 50 G1 DA/8250/* DA/8250/M/* 1" DC/8250/* DC/8250/M/* QA/8250/00 320 63 G1 DA/8320/* DA/8320/M/* 1" DC/8320/* DC/8320/M/* QA/8320/00 * Insert stroke length in mm. Standard models Cylinder diameters (mm) Substitute 032, 040, 050, 063, 080, 100, 125, 160, 200, 250, 320 Special variants Substitute Heat resistant seals, 150°C max. T Variants (non-magnetic piston) Substitute Standard None Special wiper/seal W1 Low friction X1 Piston rod bellow G Without cushioning W Without cushioning, low friction X3 Double ended piston rod J Double ended piston rod, special wiper/seal W3 Four position IT Non-rotating piston rod N1* Locking unit L2 Extended piston rod IU Extended piston rod, special wiper/seal W5 **A/8000/IU/**/***/*** /W5/ Extension (mm) Piston rod material Substitute Chrome plated stainless steel D Variants (magnetic piston) Substitute Standard M Special wiper/seal W2 Low friction X2 Piston rod bellow MG Without cushioning MW Without cushioning, low friction X4 Double ended piston rod JM Double ended piston rod, special wiper/seal W4 Four position MT Non-rotating piston rod N2* Locking unit L4 Extended piston rod MU Extended piston rod, special wiper/seal W6 **A/8000/MU/**/***/*** /W6/ Extension (mm) Series Substitute 8000 8 Threads Substitute Metric ports: ISO 228 (G 1/8 to G 1) A NPT ports C Strokes (mm) 3000 max.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
www.norgren.com/info/US-ACT-72ACT-72
ACTUATORS
ISO/VDMA CylindersDA/8000Double actingØ 32 ... 320 mm
Conforms to ISO 6431,VDMA 24562 and NFE 49-003-1High performance, ruggednessand reliabilityExtensive range of mountingsTechnical dataMedium:Compressed air, filtered,lubricated or non-lubricated
Operating pressure:15 to 232 psig (1 to 16 bar) 15to 145 psig [1 to 10 bar] forØ 250 and 320 mm
Operating temperature:-4°F to +176°F (-20°C to+80°C ) max.Consult our Technical Servicefor use below +35°F (+2°C)
Strokes:Standard, see tableNon-standard strokes up to3000 mm maximum
MaterialsBarrel: anodized aluminumEnd covers: pressure diecastaluminium (Ø 200 to 320 mmgravity cast aluminum)Piston rod: stainless steel(Martensitic)Piston rod seals: polyurethane(Ø 125 to 320 mm nitrile rubber)Piston seals: polyurethane(Ø 125 to 320 mm nitrile rubber)‘O’-rings: nitrile rubber
Options selector˙DC / 8 0 5 0 /M˙ /˙˙˙˙
Note: If option is not required, disregard option position within part number eg. RA/8100/100For combinations of cylinder variants consult our Technical Service.
* N1 and N2 option built using non chrome plate, stainless steel piston rods
Note: Style ‘H’: These mountings are only supplied assembled complete with the cylinder. Unless otherwisespecified, units will be supplied with dimension ‘XV’ plus half the stroke length. ‘XV’ = Distance from thepiston rod shoulder to the center of the mounting.Style ‘UH’: It is most important that the locking screws which secure the mounting to the tie rod are tightenedto the torque figures shown in the table below. For maximum energy input, consult our Technical Service.
*Type – UH ***Type – H**Grease nipple up to Ø 125 mm
Adjustable center trunnion – UH (for profile types)
Ø CA CH Ø Ø H2 EM EM1 EN-0.1 ER EU G1 G2 G3 H6 K1 K2 L1 R1 Ø S Z SW SS USCN H7 CK H9 D lb lb lb
Guide blocks for ISO/VDMA cylindersQA/8000/51/*QA/8000/61/*Ø 32 ... 100mm
Conforms to ISO 6431,VDMA 24562 and NFE 49 003 1Ensures protection againstexternal rotary and bendingforcesGuide rods run throughbearings protected by wiperringsProvides accurate guidance forunsupported loadsTechnical dataOperating temperature:+32°F to +176°F (0°C to+80°C) maximum
* Insert stroke length in mm.Locking cartridges should be ordered separately. Active – pressure applied to lock, passive – pressure released to lock. 2 required per guide block.Note: For all applications please consult our Technical Service# When using guide blocks (QA/8000/61) for profile cylinders PDA/182000 you have to order a model with a barrel which is turned at 90° so that theport threads are in line with the two switch grooves.
Ø AC + ** AD AE (A/F) AF (A/F) AG AH AJ AK** AL Ø AM AN AO32 69 + 2 12 15 17 M 6 10 32.5 110 58 10 6 940 74 + 2 12 15 19 M 6 10 38 122 64 12 6 1150 91.5 + 4 15 22 24 M 8 12 46.5 135 80 12 6 1963 92 + 4 15 22 24 M 8 12 56.5 153 95 12 7 1580 106 + 6 15 27 30 M 10 15 50 180 130 16 9 14100 111 + 6 15 27 30 M 10 15 70 199 150 16 9 19Ø AP AR AS AT AV … AW Ø AX AZ BA BB at 0 mm per 10032 100 90 74 78 45 32.5 6.6 48 76 9 2.20 lb 0.13 lb40 106 100 80 84 50 38 6.6 56 85 11 2.65 lb 0.20 lb50 125 120 96 100 60 46.5 9 66 99 19 3.97 lb 0.20 lb63 132 125 104 105 70 56.5 9 76 114 15 4.90 lb 0.20 lb80 165 155 130 130 90 72 11 98 134.5 25 9.04 lb 0.35 lb100 185 175 150 150 110 89 11 118 153.5 28.5 12.80 lb 0.35 lb
stroke
QA/8000/51/* – Guide blocks (plain bearing)
Outstroke (mm)
** Adjustment range
Load capacity
Dimensions in mm
** Adjustment rangesNote: Supplied complete with mounting screws for cylinder.
www.norgren.com/info/US-ACT-82ACT-82
ACTUATORS
Guide blocks with roller bearingsQA/8000/61/*Ø 32 ... 100 mm
CT
CJ
CY
CB + CC
CE
CD
CF ±0,2
CHCG
DM CK
CN
*****
CO
-0,3
CP
CR
CS
øC
Vf7
CW
CX ±0,2
CH
CZ
DA
-0,3
DB
±0,3
DD
VI 5
DC
DE
±0,2
T ±0,2
DF
ø DJ
DL
ø DH H7
øD
HH
7x
2,5
ø DH H7 x2,5
øD
G
**** (28 min)
ø DK f6CI **
2,5
CA +
CX
±0,2
2,5
+0,
1-
***
QA/8000/61/* – Guide blocks (roller bearing)
stroke
Ø CA** CB + ** CC CD CE CF ±0.2 CG CH CI** CJ (A/F) CK CN32 177 100 + 5 65 28 12 15.3 6.5 M 6 84.5 13 5 6140 192 111 + 5 69 33 12 23 6.5 M 6 88 15 6 6750 237 128 + 10 65 40 15 33.8 9 M 8 94 22 6 75.563 237 128 + 10 97 40 15 29.3 9 M 8 98.5 22 6 8080 280 151 + 10 112 50 20 37 11 M 10 114 27 7 92100 280 156 + 10 112 55 20 40.5 11 M 10 115.5 27 7 93¯ CO -0.3 CP CR CS CT (A/F) ¯ CV f7 CW É CX ±0.2 CY (A/F) CZ DA -0.3 DB ±0.332 97 90 74 50.5 17 12 61 32.5 5 125 50 4540 115 110 87 58.5 19 16 69 38 6 140 58 5450 137 130 104 70.5 24 20 85 46.5 6 150 70 6363 152 145 119 85.5 24 20 100 56.5 6 182 85 8080 189 180 148 105.5 30 25 130 72 8 215 105 100100 213 200 172 130.5 30 25 150 89 8 220 130 120Ø C Ø DD DE ±0.2 DF Ø DG Ø DH H7 DJ Ø DK f6 DL DM T at 0 mm per 100 mm32 6.6 11 78 M 6 22.5 9 M 5 9 70.5 14 32.5 2.65 lb 0.40 lb40 6.6 11 84 M 6 27.5 9 G 1/8 9 74.5 14 38.0 4.85 lb 0.71 lb50 9 15 100 M 8 32.5 11 G 1/8 11 91.5 16 46.5 7.94 lb 1.08 lb63 9 15 105 M 8 32.5 11 G 1/8 11 91.5 16 56.5 10.14 lb 1.08 lb80 11 18 130 M 10 54.5 13 G 1/8 13 141.5 20 72.0 19.18 lb 1.70 lb100 11 18 150 M 10 54.5 13 G 1/8 13 141.5 20 87.0 24.26 lb 1.70 lb
** Adjustment rangeNote: Supplied complete with mounting screws for cylinders and two centering sleeves.
AttentionWhen using guide blocks (QA/8000/61) for profile cylinders PDA/182000 you have to order a model with a barrel which isturned at 90° (PDA/182000/IIL, .../MIL) so that the port threads are in line with the two switch grooves.
** Adjustment range*** Centering sleeve**** Safety zone***** Blanking plug (remove when using locking cartridge)
Dimensions in mm
ACT-83
ACTUATORS
( N )
500
400
300
200
100
00 100 200
300 400 500 600
8080-81008050-806380408032
0 100 200 300 400 500 600
f
2,5
2,0
1,5
1,0
0,5
0
8032
8040
8050 - 80638080 - 8100
0 100 200 300 400 500 600
f
2,5
2,0
1,5
1,0
0,5
0
8032
8040
8050 - 80638080 - 8100
0
2
2
1
1
0
1,0
0,9
0,8
0,7
0,6
0,50 20 40 60
Guide blocks with roller bearingsQA/8000/61/*
Ø 32 ... 100 mm
***
**
*
**
f
Maximum load capacity is dependent on theoutstroke of a horizontally installed guideunit. In the case of short stroke operation,the load capacity figures taken from thediagram must be multiplied by the correctionfactor (diagram 2). In the curves of loadcapacity (diagram 1), the short strokecorrections have already been taken intoaccount for an outstroke > 60 mm.
The total deflection of guide rods will bedetermined by the addition of that due toown weight (diagram 3) and that due to loadcapacity (diagram 4).
Maximum load capacity depending on outstroke Deflection caused by own weight Deflection caused by a load of 10 N(diagram 1) (diagram 2) (diagram 3) (diagram 4)
In the case of shock load applications, the figures given in the diagrams above must be reduced by a factor of 2.
Outstroke (mm)
** Outstroke*** Center of gravity
* Center of gravity of load capacity** Outstroke
Stroke (mm) Outstroke (mm)Outstroke (mm)
www.norgren.com/info/US-ACT-84ACT-84
ACTUATORS
˙P˙A/182˙˙˙/˙˙/˙˙˙˙
Conforms to ISO 6431,VDMA 24562 and NFE 49-003-1Profile barrel with concealedtie rodsHigh performance, stability andreliabilityPolyurethane seals ensureefficient low friction operationand long lifeSwitches can be mounted flushwith the profile barrelComprehensive range ofstandard mountings
Technical dataMedium:Compressed air, filtered,lubricated or non-lubricated
Operating temperature:-4°F to +176°F(-20°C to +80°C ) max.High temperature versions:302°F (150°C) max.Consult our Technical Servicefor use below +35°F (+2°C)
Strokes:Standard: see next pageNon-standard strokes available(10 to 3000 mm)
Special variants SubstituteHeat resistant seals, 150°C max. THydraulic H Variants (non-magnetic piston)Substitute
Standard NoneSpecial wiper/seal W1Low friction X1Piston rod bellow GWithout cushioning WWithout cushioning, low friction X3Double ended piston rod JDouble ended piston rod,special wiper/seal W3Four-position ITNon-rotating piston rod N1Locking unit L2Barrel turned at 90° for use withguide blocks QA/8000/61/* IILExtended piston rod IUExtended piston rod,special wiper/seal W5P*A/182***/IU/****/***
/W5/ Extension (mm)
Note: Disregard option positions not used.For combinations of cylinder variants consultour Technical Service.
Piston rod material SubstituteChrome plated stainless steel D
Variants (magnetic piston) SubstituteStandard MSpecial wiper/seal W2Low friction X2Piston rod bellow MGWithout cushioning MWWithout cushioning, low friction X4Double ended piston rod JMDouble ended piston rod &special wiper/seal W4Four-position MTNon-rotating piston rod N2Locking unit L4Barrel turned at 90° MILfor use with guide blocksExtended piston rod MUExtended piston rod & W6special wiper/sealP*A/182***/MU/****/***
/W6/ Extension (mm)
*Insert stroke length in mm.
Standard models
Threads SubstituteMetric ports: ISO 228 (G 1/8 to G 1) ANPT ports C
Ø L 8 L 10 L 1132 94 247 740 105 278 850 106 294 863 121 325 980 128 357 9100 138 387 9125 160 462 12
Dimensions in mm
www.norgren.com/info/US-ACT-88ACT-88
ACTUATORS
Magnetic and non-magneticpiston conforms to ISO 6431,VDMA 24562 and NFE 49-003-1Secure locking of piston rod inany positionPassive locking modelsCompact, maintenance-freedesign
Technical dataMedium:Compressed air, filtered,lubricated or non-lubricated
Type:Passive model – pressureapplied to release
Operating pressure:58 to 145 psig (4 to 10 bar)
Operating temperature:+32°F to 176°F (0°C to +80°C).Consult our Technical Service foruse below +35°F (+2°C).
Cylinders with piston rod locking units(ISO/VDMA/NFE)PDA/182000/L2 & L4, RA/8000/L2 & L4Ø 32 ... 125 mm
Passive
* Insert stroke length in mm.Locking unit includes cartridgeFor non-magnetic versions substitute L2 for L4.For all applications please consult our Technical Service.
Magnetic Non-magneticISO/VDMA/NFE ISO/VDMA/NFE ISO/VDMA/NFE ISO/VDMA/NFE