The Extron ® ISM HDSDI is a universal video and RGB scaler board with HDSDI output for the ISM 824. It has a single BNC connector and a local audio output. The board mounts in one of the four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824. Refer to the ISM 824 User Guide, available at www.extron.com. To install an ISM HDSDI output board in the ISM 824 base unit: 1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices. 2. Select an open slot at the rear, or take out a blank plate by removing the two retaining screws (top and bottom), and lifting the plate away. NOTE: Retain and reuse the screws to secure the new output board in place. Retain the blank plates. If a board is already installed in the desired slot, remove the screws and carefully pull out the board. 3. Holding the new board by the frame, align the front (non-connector end) of the board with the top and bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides. Push it into place firmly, and secure it with the retained screws. 4. If required, repeat steps 2 through 4 for any other output boards. 5. Power on the ISM 824. The new output board(s) is autodetected, and takes approximately 30 seconds to initialize. The 16 character LCD display indicates the new board type, slot used, and counts down the initialization time. See inset for example display of a new ISM HDSDI board installed in slot #2, with 16 seconds left. 6. Connect a suitable display device to the BNC connector. The output can be configured via the front panel (see page 2) or by SIS ™ commands (see page 3). 7. Insert a 5-pole captive screw connector into the local audio output connector for balanced or unbalanced stereo output. Wire the connector as shown below. 1 8 1 2 2 1 OUTPUTS R/R-Y G/Y VID B/C B-Y H/HV V PASS THRU OUTPUT 3 R/ R-Y G/Y B/ B-Y H/ HV V OUTPUT 5 R/ R-Y G/Y B/ B-Y H/ HV V OUTPUT 8 R/ R-Y G/Y B/ B-Y H/ HV V ISM 824 Integration Scaling Matrix Switcher Align output board with top and bottom plastic guides. R/ R-Y G/Y B/ B-Y H/ HV V OUTPUT 7 Example Output Board Installation ISM HDSDI Output Board • Setup Guide New Univ HDSDI Slot #2 16 ISM HDSDI HDSDI UNIVERSAL SCALER HDSDI L R Unbalanced Stereo Output Balanced Stereo Output Tip Ring Sleeve(s) Tip Ring L R Left Right Tip Sleeve(s) Tip L R Left Right NO GROUND HERE. NO GROUND HERE. CAUTION: For unbalanced audio, DO NOT connect the sleeves to the negative contacts. Connect to center ground contact.
4
Embed
ISM HDSDI Output Board Setup Guide - Extron Electronics · To install an ISM HDSDI output board in the ISM 824 base unit: 1. ... +65.6383.4400 +65.6383.4664 FAX Extron Japan +81.3.3511.7655
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
The Extron® ISM HDSDI is a universal video and RGB scaler board with HDSDI output for the ISM 824. It has a single BNC connector and a local audio
output. The board mounts in one of the four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824. Refer to the ISM 824 User Guide, available at www.extron.com.
To install an ISM HDSDI output board in the ISM 824 base unit:
1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.
2. Select an open slot at the rear, or take out a blank plate by removing the two retaining screws (top and bottom), and lifting the plate away.
NOTE: Retain and reuse the screws to secure the new output board in place. Retain the blank plates. If a board is already installed in the desired slot, remove the screws and carefully pull out the board.
3. Holding the new board by the frame, align the front (non-connector end) of the board with the top and bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides. Push it into place firmly, and secure it with the retained screws.
4. If required, repeat steps 2 through 4for any other output boards.
5. Power on the ISM 824. The new output board(s) is autodetected, and takes approximately 30 seconds to initialize. The 16 character LCD display indicates the new board type, slot used, and counts down the initialization time. See inset for example display of a new ISM HDSDI board installed in slot #2, with 16 seconds left.
6. Connect a suitable display device to the BNC connector. The output can be configured via the front panel (see page 2) or by SIS™ commands (see page 3).
7. Insert a 5-pole captive screw connector into the local audio output connector for balanced or unbalanced stereo output. Wire the connector as shown below.
1
100-24050/60 H
z
1.2A MAX.
1
2
3
4
5
6
7
8
2
1
2
3
4
5
6
7
8
1
2
1
INPUTS
OUTPUTS
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
PASS THRU
INPUTS
RESET
LA
NR
EM
OT
E
RS
232/
RS
422
AC
TL
INK
OUTPUT
VIDEO
SCALER
70-545-01
3 R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNIV.
SCALER
70-544-01
5 R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PASS
THRU
70-547-01
8 R/
R-Y
G/Y
B/
B-Y
H/
HV
V
ExtronISM 824Integration ScalingMatrix Switcher
Align output boardwith top and bottomplastic guides.
ISM HDSDI Configuration MenuUsing the front panel menu buttons (Menu and Next), the ISM HDSDI configuration menu can be accessed. From the Output Configuration screen, press Next until reaching the #x Univ HDSDI menu (see the image below). Press Menu and Next to navigate through the menus and use the front panel Adjust knobs ({ [), to change the settings as desired. Refer to the ISM 824 User Guide, online at www.extron.com for full details.
From the default cycle press Menu repeatedly to reach the Output Configuration menu. Press Next (enters Select Output menu) and rotate either Adjust knob to select the Univ HDSDI menu. Follow the figure below to enter each menu and use the Adjust knobs to change the value.
Select Output#8 Univ HDSDI
Next
Input Setup#8 Univ HDSDI
Aspect Ratio4:3
Next
Rotate either knobto select Aspect Ratio (4:3 or 16:9).
Rotate knob to adjust Total Pix value.Rotate knob toadjust Phase value. .Next
H Active V1283 1028
Rotate knob to adjust H active value.Rotate knob toadjust V active value.
Menu
Next
Output Config#8 Univ HDSDI
Rotate knob to adjust resolution. Rotate knob toadjust refresh rate.
Next
1080i 60 HzResolution
Next
Menu
User Presets#8 Univ HDSDI
30 sec.
<NA> 1 2 3Save Preset
Next
Rotate either knobto select a preset to save current settings.
<NA> 1 2 3Erase Preset
Next
Rotate either knobto select a presetto erase.
Advanced Config#8 Univ HDSDI
Next
NoneTest Pattern
Rotate either knobto select a test pattern.
<Off> OnBlue Mode
Next
Rotate either knobto turn blue mode Onor Off.
Next
Off <On>Film Mode
Rotate either knobto turn film mode Onor Off.
Next
Menu
Next
Next
Rotate knob to select input.Rotate knob toturn On or Off.
Input #2 OffAuto Image
Auto Memory
Next
Rotate either knobto turn auto memories On or Off.
Off <On>
Input #2 OffFull Screen
Rotate knob to select input.Rotate knob toturn On or Off.
Next
NOTE: Within any submenu, press the Menu buttonto go directly to the top level (Output Card Configuration) menu. If, for 30 seconds, no button is pressed or Adjust knob is rotated,the menu times out and reverts to the defaultdisplay cycle.
Input Setup
The Input Setup submenu allows configuration of aspect ratio, horizontal and vertical start points, total pixels and phase value, and active horizontal and vertical areas. Rotate the Adjust knobs as required to change values.
The Output Config submenu displays and allows changes to be made to the resolution and refresh rate. Use the Adjust knobs to select a resolution and refresh rate.
Resolution 24 Hz 25 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz
720p X X X X X X
1080i X X X
1080p X X X
User Presets
The User Presets submenu displays and allows the current settings to be saved as a preset, or to erase an existing saved preset. Use the Adjust knobs to select between the presets.
Advanced Config
Within this submenu the following settings can be adjusted: auto image (on or off), test pattern (selection), blue mode (on or off), auto memories (on or off), film mode (on or off), and full screen (on or off).
Test Pattern
The test pattern submenu offers the following test patterns to choose from:
Color Bars Split Grayscale4x4 Crosshatch AlternatingPixels
Board-specific SIS CommandsThe ISM HDSDI board can be configured with specific Simple Instruction Set™ (SIS) commands. The table below and on page 4 lists some of the ISM HDSDI board specific commands. Refer to the ISM 824 User Guide, at www.extron.com for a list.
Command ASCII Command (host to ISM)
Response(ISM to host)
Additional Description
Input selection
Video and audio X!*X@! OutX@•InX!•All] Tie video/audio input X! to X@.
Video X!*X@& OutX@•InX!•RGB] Select video input X! to X@.
Audio X!*X@$ OutX@•InX!•Aud] Select audio input X! to X@.