FN6937 Rev 3.00 Page 1 of 20 March 8, 2012 FN6937 Rev 3.00 March 8, 2012 ISL6185 Dual USB Port Power Supply Controller DATASHEET The ISL6185 USB power controller family provides fully independent overcurrent (OC) fault protection for two or more USB ports. This product family consists of sixteen individual functional product variants and three package options. It is operation rated for a nominal +2.5V to +5V range and is specified over the full commercial and industrial temperature ranges. Each ISL6185 type incorporates in a single package two 71mP-channel MOSFET power switches for power control. Each features internal current monitoring, accurate current limiting, and current limited delay to turn-off, for system supply protection along with control and communication I/O. The ISL6185 family offers product variants with specified continuous output current levels of 0.6A, 1.1A, 1.5A or 1.8A; enable active high or low inputs; and latch off or automatic retry after overcurrent turn-off, making these devices well suited for many low-power applications. This family of ICs is offered in an industry-standard SOIC pinout and also in the 70% smaller 3x3 DFN packages providing similar or enhanced performance in the smallest possible package. Features • 2.5V to 5V Operating Range • 71mIntegrated Power P-channel MOSFET Switches • Continuous Current Options for 0.6A, 1.1A, 1.5A and 1.8A • Thermally Insensitive 12ms of Current Limiting Prior to Turn-Off • Output Discharges with Reverse Current Blocking When Disabled • Latch-off or Auto Restart Options • 1μA Off-State Supply Current • Enable Polarity Options • Industry-standard Pin for Pin SOIC, and Smaller DFN Packages Available • UL Recognized, File Number: E333469 Applications • USB 1, 2, 3 Port Power Management • Low Power (18W) Electronic Circuit Limiting and Breaker FIGURE 1. TYPICAL APPLICATION FIGURE 2. NORMALIZED r DS(ON) TEMPERATURE CHARACTERISTIC CURVE D+ D- D+ D- +5V VIN ENABLE_2 FAULT_1 ENABLE_1 FAULT_2 GND OUT_1 OUT_2 ISL6185 U S B C O N T R O L L E R VBUS VBUS USB PORT 1 USB PORT_2 USB PORT POWER 0.7 0.8 0.9 1.0 1.1 1.2 1.3 -40 -25 0 25 45 75 85 115 TEMPERATURE (°C) NORMALIZED r DS(ON)
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
FN6937Rev 3.00
March 8, 2012
ISL6185Dual USB Port Power Supply Controller
DATASHEET
The ISL6185 USB power controller family provides fully independent overcurrent (OC) fault protection for two or more USB ports.
This product family consists of sixteen individual functional product variants and three package options. It is operation rated for a nominal +2.5V to +5V range and is specified over the full commercial and industrial temperature ranges.
Each ISL6185 type incorporates in a single package two 71m P-channel MOSFET power switches for power control. Each features internal current monitoring, accurate current limiting, and current limited delay to turn-off, for system supply protection along with control and communication I/O.
The ISL6185 family offers product variants with specified continuous output current levels of 0.6A, 1.1A, 1.5A or 1.8A; enable active high or low inputs; and latch off or automatic retry after overcurrent turn-off, making these devices well suited for many low-power applications.
This family of ICs is offered in an industry-standard SOIC pinout and also in the 70% smaller 3x3 DFN packages providing similar or enhanced performance in the smallest possible package.
Features• 2.5V to 5V Operating Range
• 71m Integrated Power P-channel MOSFET Switches
• Continuous Current Options for 0.6A, 1.1A, 1.5A and 1.8A
• Thermally Insensitive 12ms of Current Limiting Prior to Turn-Off
• Output Discharges with Reverse Current Blocking When Disabled
• Latch-off or Auto Restart Options
• 1µA Off-State Supply Current
• Enable Polarity Options
• Industry-standard Pin for Pin SOIC, and Smaller DFN Packages Available
• UL Recognized, File Number: E333469
Applications• USB 1, 2, 3 Port Power Management
• Low Power (18W) Electronic Circuit Limiting and Breaker
ISL61851ACBZ 61851A CBZ EN 0.6 LATCH 0 to +70 8 Lead SOIC M8.15
ISL61851BCBZ 61851B CBZ EN 0.6 RETRY 0 to +70 8 Lead SOIC M8.15
ISL61851CCBZ 61851C CBZ EN 1.1 LATCH 0 to +70 8 Lead SOIC M8.15
ISL61851DCBZ 61851D CBZ EN 1.1 RETRY 0 to +70 8 Lead SOIC M8.15
ISL61851ECBZ 61851E CBZ EN 0.6 LATCH 0 to +70 8 Lead SOIC M8.15
ISL61851FCBZ 61851F CBZ EN 0.6 RETRY 0 to +70 8 Lead SOIC M8.15
ISL61851GCBZ 61851G CBZ EN 1.1 LATCH 0 to +70 8 Lead SOIC M8.15
ISL61851HCBZ 61851H CBZ EN 1.1 RETRY 0 to +70 8 Lead SOIC M8.15
ISL61851ICBZ 61851I CBZ EN 1.5 LATCH 0 to +70 8 Lead SOIC M8.15
ISL61851JCBZ 61851J CBZ EN 1.5 RETRY 0 to +70 8 Lead SOIC M8.15
ISL61851KCBZ 61851K CBZ EN 1.5 LATCH 0 to +70 8 Lead SOIC M8.15
ISL61851LCBZ 61851L CBZ EN 1.5 RETRY 0 to +70 8 Lead SOIC M8.15
ISL61852ACRZ 52AC EN 0.6 LATCH 0 to +70 8 Lead DFN L8.3x3J
ISL61852BCRZ 52BC EN 0.6 RETRY 0 to +70 8 Lead DFN L8.3x3J
ISL61852CCRZ 52CC EN 1.1 LATCH 0 to +70 8 Lead DFN L8.3x3J
ISL61852DCRZ 52DC EN 1.1 RETRY 0 to +70 8 Lead DFN L8.3x3J
ISL61852ECRZ 52EC EN 0.6 LATCH 0 to +70 8 Lead DFN L8.3x3J
FN6937 Rev 3.00 Page 2 of 20March 8, 2012
ISL6185
ISL61852FCRZ 52FC EN 0.6 RETRY 0 to +70 8 Lead DFN L8.3x3J
ISL61852GCRZ 52GC EN 1.1 LATCH 0 to +70 8 Lead DFN L8.3x3J
ISL61852HCRZ 52HC EN 1.1 RETRY 0 to +70 8 Lead DFN L8.3x3J
ISL61852ICRZ 52IC EN 1.5 LATCH 0 to +70 8 Lead DFN L8.3x3J
ISL61852JCRZ 52JC EN 1.5 RETRY 0 to +70 8 Lead DFN L8.3x3J
ISL61852KCRZ 52KC EN 1.5 LATCH 0 to +70 8 Lead DFN L8.3x3J
ISL61852LCRZ 52LC EN 1.5 RETRY 0 to +70 8 Lead DFN L8.3x3J
ISL61853ACRZ 53AC EN 0.6 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853BCRZ 53BC EN 0.6 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853CCRZ 53CC EN 1.1 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853DCRZ 53DC EN 1.1 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853ECRZ 53EC EN 0.6 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853FCRZ 53FC EN 0.6 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853GCRZ 53GC EN 1.1 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853HCRZ 53HC EN 1.1 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853ICRZ 53IC EN 1.5 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853JCRZ 53JC EN 1.5 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853KCRZ 53KC EN 1.5 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853LCRZ 53LC EN 1.5 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853MCRZ 53MC EN 1.8 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853NCRZ 53NC EN 1.8 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61853OCRZ 53OC EN 1.8 LATCH 0 to +70 10 Lead DFN L10.3x3
ISL61853PCRZ 53PC EN 1.8 RETRY 0 to +70 10 Lead DFN L10.3x3
ISL61851AIBZ 61851A IBZ EN 0.6 LATCH -40 to +85 8 Lead SOIC M8.15
ISL61851BIBZ 61851B IBZ EN 0.6 RETRY -40 to +85 8 Lead SOIC M8.15
ISL61851CIBZ 61851C IBZ EN 1.1 LATCH -40 to +85 8 Lead SOIC M8.15
ISL61851DIBZ 61851D IBZ EN 1.1 RETRY -40 to +85 8 Lead SOIC M8.15
ISL61851EIBZ 61851E IBZ EN 0.6 LATCH -40 to +85 8 Lead SOIC M8.15
ISL61851FIBZ 61851F IBZ EN 0.6 RETRY -40 to +85 8 Lead SOIC M8.15
ISL61851GIBZ 61851G IBZ EN 1.1 LATCH -40 to +85 8 Lead SOIC M8.15
ISL61851HIBZ 61851H IBZ EN 1.1 RETRY -40 to +85 8 Lead SOIC M8.15
ISL61851IIBZ 61851I IBZ EN 1.5 LATCH -40 to +85 8 Lead SOIC M8.15
ISL61851JIBZ 61851J IBZ EN 1.5 RETRY -40 to +85 8 Lead SOIC M8.15
ISL61851KIBZ 61851K IBZ EN 1.5 LATCH -40 to +85 8 Lead SOIC M8.15
ISL61851LIBZ 61851L IBZ EN 1.5 RETRY -40 to +85 8 Lead SOIC M8.15
ISL61852AIRZ 52AI EN 0.6 LATCH -40 to +85 8 Lead DFN L8.3x3J
ISL61852BIRZ 52BI EN 0.6 RETRY -40 to +85 8 Lead DFN L8.3x3J
ISL61852CIRZ 52CI EN 1.1 LATCH -40 to +85 8 Lead DFN L8.3x3J
ISL61852DIRZ 52DI EN 1.1 RETRY -40 to +85 8 Lead DFN L8.3x3J
ISL61852EIRZ 52EI EN 0.6 LATCH -40 to +85 8 Lead DFN L8.3x3J
Ordering Information (Continued)
PARTNUMBER
(Notes 1, 2, 3) PART MARKINGEN/ENINPUT
VIN = 5V MAXIMUM
CONTINUOUS IOUT (A)
LATCH/AUTO RETRY
TEMP.RANGE (°C)
PACKAGE(Pb-free)
PKG.DWG. #
FN6937 Rev 3.00 Page 3 of 20March 8, 2012
ISL6185
ISL61852FIRZ 52FI EN 0.6 RETRY -40 to +85 8 Lead DFN L8.3x3J
ISL61852GIRZ 52GI EN 1.1 LATCH -40 to +85 8 Lead DFN L8.3x3J
ISL61852HIRZ 52HI EN 1.1 RETRY -40 to +85 8 Lead DFN L8.3x3J
ISL61852IIRZ 52II EN 1.5 LATCH -40 to +85 8 Lead DFN L8.3x3J
ISL61852JIRZ 52JI EN 1.5 RETRY -40 to +85 8 Lead DFN L8.3x3J
ISL61852KIRZ 52KI EN 1.5 LATCH -40 to +85 8 Lead DFN L8.3x3J
ISL61852LIRZ 52LI EN 1.5 RETRY -40 to +85 8 Lead DFN L8.3x3J
ISL61853AIRZ 53AI EN 0.6 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853BIRZ 53BI EN 0.6 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853CIRZ 53CI EN 1.1 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853DIRZ 53DI EN 1.1 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853EIRZ 53EI EN 0.6 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853FIRZ 53FI EN 0.6 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853GIRZ 53GI EN 1.1 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853HIRZ 53HI EN 1.1 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853IIRZ 53II EN 1.5 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853JIRZ 53JI EN 1.5 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853KIRZ 53KI EN 1.5 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853LIRZ 53LI EN 1.5 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853MIRZ 53MI EN 1.8 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853NIRZ 53NI EN 1.8 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61853OIRZ 53OI EN 1.8 LATCH -40 to +85 10 Lead DFN L10.3x3
ISL61853PIRZ 53PI EN 1.8 RETRY -40 to +85 10 Lead DFN L10.3x3
ISL61851EVAL1Z 8 Lead SOIC Evaluation Platform with ISL61851A installed
ISL61852EVAL1Z 8 Lead DFN Evaluation Platform with ISL61852H installed
ISL61853EVAL1Z 10 Lead DFN Evaluation Platform with ISL61853I installed
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information pages for ISL6185XXC (commercial version) and ISL6185XXI (industrial version). For more information on MSL please see techbrief TB363.
2 2, 3 VIN Chip bias, Controlled Voltage Input, Undervoltage Lock Out (UVLO). VIN provides chip bias voltage. At VIN < 1.7V chip functionality is disabled, FLT is active and floating, and OUT is held low. Range 0V to 5.5V.
3, 4
4, 5
EN1, EN1/EN2, EN2
Enable/Disable inputs, Active high (EN) and active low (EN) options enable the power switch. These inputs have internal 1M pull-off resistors. Range 0V to VIN.
5, 8
6, 10
FLT2FLT1
Overcurrent Fault Indicator. FLT floats and is disabled until VIN >VUVLO. This output is pulled low after the current limit time-out period has expired. Fault is not signaled due to over-temperature shut down. Range 0V to VIN.
6, 7
7, 9
OUT2, OUT1
Controlled Supply Output. Upon an OC condition, IOUT is current limited. Current limit response time is within 200µs. This output remains in current limit for a nominal 12ms before being turned off either for the latch or auto retry versions. Range 0V to VIN.
- 8 NC This pin is not electrically connected internally.
PD (DFN only)
PD EPAD Thermal Dissipation Exposed PAD Range: Connect to GND.
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact productreliability and result in failures not covered by warranty.
NOTES:
4. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
5. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379.
6. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
7. All voltages are relative to GND, unless otherwise specified.
Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0°C to +75°C or -40°C to +85°C.
SYMBOL PARAMETER TEST CONDITIONSMIN
(Note 8) TYPMAX
(Note 8) UNITS
POWER SWITCH
rDS(ON)_50 ON-Resistance at 5.0V (Pulse Tested) VIN = 5V, IOUT = 0.1A, TA = TJ = +25°C - 71 87 m
TA = TJ = +85°C - 110 m
rDS(ON)_33 ON-Resistance at 3.3V (Pulse Tested) VIN = 3.3V, IOUT = 0.1A, TA = TJ = +25°C - 90 105 m
TA = TJ = +85°C - 130 m
rDS(ON)_25 On Resistance at 2.5V (Pulse Tested) VIN = 2.5V, IOUT = 0.1A, TA = TJ = +25°C - 114 127 m
Isc_5 Short Circuit Current, VIN = 5V ISL6185xA,B,E,F, VOUT = 0V 0.60 0.80 1.00 A
Isc_5 ISL6185xC,D,G,H, VOUT = 0V 1.00 1.27 1.55 A
Isc_5 ISL6185xI,J,K,L, VOUT = 0V 1.15 1.61 1.85 A
Isc_5 ISL61853M,N,O,P, VOUT = 0V 1.20 1.70 2.5 A
Isc_3 Short Circuit Current, VIN = 3.3V ISL6185XA,B,E,F, VOUT = 0V 0.35 0.48 0.60 A
Isc_3 ISL6185XC,D,G,H, VOUT = 0V 0.65 0.80 0.95 A
Isc_3 ISL6185xI,J,K,L, VOUT = 0V 0.70 1.06 1.25 A
Isc_3 ISL61853M,N,O,P, VOUT = 0V 0.90 1.24 1.50 A
Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0°C to +75°C or -40°C to +85°C. (Continued)
SYMBOL PARAMETER TEST CONDITIONSMIN
(Note 8) TYPMAX
(Note 8) UNITS
FN6937 Rev 3.00 Page 7 of 20March 8, 2012
ISL6185
Isc_2 Short Circuit Current, VIN = 2.5V ISL6185xA,B,E,F, VOUT = 0V - 0.61 A
Isc_2 ISL6185xC,D,G,H, VOUT = 0V - 1.06 - A
Isc_2 ISL6185xI,J,K,L, VOUT = 0V - 1.30 - A
Isc_2 ISL61853M,N,O,P, VOUT = 0V - 1.39 - A
Isc_5.5 Short Circuit Current, VIN = 5.5V All ISL6185X Variants - - 2.5 A
tsettIlim OC to Limit Settling Time VIN/RL = 2ILIMCL = 10µF to within 10% of ILIM - 200 - µs
tsettIlim_sev Severe OC to Limit Settling Time VIN/RL = 4ILIMCL = 10µF to within 10% of ILIM - 30 - µs
tCL Current Limit Duration IOUT = ILIM 9.2 12 15 ms
tRTY Automatic Retry Period 0.80 1 1.35 s
I/O PARAMETERS
Vfault_lo Fault Output Voltage Fault IOUT = 10mA - - 0.4 V
Ifault Fault Leakage - 5 - µA
Venr_5 EN / EN Rising Threshold VIN = 5V 1.5 1.8 2 V
Hys_Venr_5 EN / EN Rising Threshold Hysteresis VIN = 5V 80 140 175 mV
Venr_3 EN / EN Rising Threshold VIN = 3.3V 1.0 1.3 1.6 V
Hys_Venr_3 EN / EN Rising Threshold Hysteresis VIN = 3.3V 58 80 120 mV
Venr_2 EN / EN Rising Threshold VIN = 2.5V 0.95 1.1 1.3 V
Hys_Venr_2 EN / EN Rising Threshold Hysteresis VIN = 2.5V 30 70 110 mV
Ren_h ENABLE Pull-Down Resistor Enable asserted high options 0.6 1 1.55 M
NOTE:8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0°C to +75°C or -40°C to +85°C. (Continued)
SYMBOL PARAMETER TEST CONDITIONSMIN
(Note 8) TYPMAX
(Note 8) UNITS
FN6937 Rev 3.00 Page 8 of 20March 8, 2012
ISL6185
IntroductionThe ISL6185 is a dual channel fully independent overcurrent (OC) fault protection IC for the +2.5V to +5V environment. Each ISL6185 incorporates in a single package two 85m P-channel MOSFET power switches for power control. Independent enabling inputs and fault reporting outputs compatible with 2.5V to 5V logic allow for external control and reporting. This device features integrated power switches with current monitoring, accurate current limiting, reverse bias protection and current limited timed delay to turn-off for system reliability. See Figures 13 through 28 for typical operational waveforms including both under-current and over-current situations.
The ISL6185 offers current sense and limiting, with VIN = 5V guaranteed continuous current product variants of 0.6A, 1.1A, 1.5A and 1.8A, making these devices well suited for a myriad of USB and other low power (9W max) port power management applications and configurations.
The ISL6185 also provides thermally insensitive timed OC turn-off and fault notification. This isolates and protects the voltage bus in the event of a peripheral OC event or short circuit event, independent of the adjoining switch’s electrical or the ambient thermal condition.
The ISL6185 undervoltage lockout feature prevents turn-on of the outputs unless the correct ENABLE state and VIN > VUVLO are present. During initial turn-on, the ISL6185 prevents fault reporting by blanking the fault signal.
During operation, once an OC condition is detected, the output is current limited for tCL to allow transient OC conditions to pass. If still in current limit after the current limit period has elapsed, the output is turned off, and the fault is reported by pulling the corresponding FAULT output low. On the latch-off options, after turn-off, both the output and the FAULT signal are latched low until reset by the enable signal being de-asserted or until a POR occurs. At this time, the FAULT signal clears, and the switch is ready to be turned back on. On the auto restart options, the ISL6185 attempts to periodically turn on the output, as long as the enable is asserted.
When disabled, the ISL6185 has a low quiescent supply current and an output-to-input reverse current flow blocking capability.
The ISL6185 family is provided with enable polarity options and an industry-standard 8 lead SOIC pinout, along with two versions in the 70% smaller 3x3 DFN. The 8 Ld DFN package offers the same performance as the 8 Ld SOIC, whereas the 10 Ld DFN offers higher current capability in the smallest possible package because of lower package electrical and thermal resistance.
Functional DescriptionPower On Preset (POR)The ISL6185 POR feature inhibits device functionality when VIN < VUVLO.
Reverse Polarity ProtectionIn any event in which the power switch is disabled and VOUT > VIN, there will be no output-to-input current flow, nor will the output voltage appear on the input.
Soft-StartUpon enable, the switch passes a constant current to the load. The voltage on the VOUT pin ramps up according the equation, ILIM/COUT (V/s). Resistive or active load slows the VOUT ramp-up toward the top of its curve.
Fault Blanking On Start-UpDuring initial turn-on, the ISL6185 prevents nuisance faults from being reported to the system controller by blanking the fault signal until the internal FET is fully enhanced.
Current Trip and Limiting LevelsThe ISL6185 provides integrated current sensing in the MOSFET that allows for rapid control of OC events. Once an OC condition is detected, the ISL6185 goes into its current limiting (CL) control mode. The ISL6185 is variant specified to allow a continuous current (ICONT) operation of 0.6A, 1.1A, 1.5A or 1.8A. As the current increases past its continuous current rating, it will reach a level that causes the device to enter its current limit mode; that is, the current trip level. The current trip level is in all cases adequately above the ICONT rating so as not to cause unintended false faults. The current limit is specified at VOUT = VIN - 1V to test a known representative condition and is featured at a nominal value slightly higher than the continuous current rating. The speed of this current limiting control is inversely related to the magnitude of the OC fault. Thus, a hard overcurrent is more quickly pulled to its limiting value than a marginal OC condition.
Over-Temperature ShutdownAlthough the ISL6185 has an over-temperature shutdown and lockout feature, because of the 12ms timed shutdown, the thermal shutdown is likely to be invoked only in extremely high ambient temperatures.
The over-temperature protection invokes and disables the switch turn-on operation once the die temperature is ~+140°C. It turns off an already on switch at ~+150°C and releases the part to operation once the die temperature falls to ~+120°C.
FN6937 Rev 3.00 Page 9 of 20March 8, 2012
ISL6185
Turn-off Time DelayDuring operation, once an OC condition is detected, the output is current limited for ~12ms to allow transient OC conditions to pass. If still in current limit and after the current limit period has elapsed, the output is turned off, and the fault is reported by pulling the corresponding FAULT low. The internal 12ms timer starts upon current limiting and is independent of ambient or IC thermal conditions, thus providing more consistent operation over the entire temperature range.
Latch-off Restart/Auto-Restart StartAfter turn-off, with the latch-off options, both the output and the FAULT signal are latched low until they are reset by the enable signal being de-asserted. At this time, the FAULT signal clears, and the IC is ready for enable to assert. On the auto restart options, the ISL6185 attempts to periodically turn-on the output at approximately 1s intervals, as long as the enable is asserted. If the OC condition remains indefinitely, the fault indication and the restart attempts also continue until the thermal protection feature is invoked, thus increasing the restart period.
Active Output Pull-downAnother ISL6185 feature is the 10k active pull-down on the outputs to <60mV above GND when the device is disabled, thus ensuring discharge of the load.
FIGURE 32. ISL6185xEVAL1Z SCHEMATIC and ISL61851EVAL1Z PHOTOGRAPH
NOTE: EXPOSED PAD on DFN packages only
U1
ISL6185
R1
10k
AGNDV+
EN1
EN2
C1
2.2
µF
R2
10k
FLT1
FLT2
OUT1OUT2
R3
C2
10µF
AGND
FLT1OUT1
OUT2
FLT2
R4
C3
10µF
10
10
A
AAA
AV+
FN6937 Rev 3.00 Page 15 of 20March 8, 2012
ISL6185
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as notedin the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
For additional products, see www.intersil.com/en/products.html
Application Information Using the ISL6185xEVAL1Z PlatformGeneral and Biasing InformationThere are three evaluation platforms for the ISL6185 family. There is one platform for each package style, each with a different continuous output current level and a mix of enable polarity and output retry or latch options. See page 4, at the end of the “Ordering Information” table, for information on the standard available evaluation board options. Figure 32A shows the common schematic for all three evaluation boards. See “Pin Configurations” on page 5 for details and differences.
The evaluation platform is biased and monitored through numerous labeled test points. See Table 1 for test point assignments and descriptions.
Upon proper bias of the evaluation platform and correct enabling of the IC, the ISL6185 will have a nominal VIN/10 load current that is lower than the continuous current rating passing through each enabled switch. See Figures 13 and 14 for typical ISL6185 turn-on and turn-off waveforms.
External current loading in excess of the trip current level for the particular part being evaluated will result in the ISL6185 entering the current limiting mode. Figure 16 illustrates the current limiting mode for the ISL6185 product variants with 0.6A of continuous load current rating. The scope shot shows current limiting for ~12ms before it is turned off and the fault signal is asserted.
Application ConsiderationsThe application considerations for the ISL6185 family are widely accepted best industry practices. Good decoupling practices on the VIN pin must be followed: placement close to the IC, with at least 2.2µF recommended. It is recommended to reduce the input and output inductance to the ISL6185 with good PCB layout practices.
When designing with the 1.5A and 1.8A versions in an implementation in which the output may be unloaded (open) while the ISL6185 is turned on, a minimum of 4.7µF of capacitive output load is recommended to prevent high dv/dt from unnecessarily activating the surge/ESD control circuit.
The ISL6185 provides several continuous current rated devices specified at VIN = 5V; these are 0.6A, 1.1A, 1.5A and 1.8A options that are capable over the entire temperature extreme. At VIN = 3.3V, the current capability is degraded, and the ISL6185 is specified at 0.6A, 1.1A, 1.3A and 1.5A, respectively. At VIN = 2.5V, there are no minimum specifications, but a typical value is provided for +25°C operation (see “Electrical Specifications” on page 6). This degraded capability is due to the higher rDS(ON) of the FET switch at the lower bias voltage.
The enhanced thermal characteristics and increased number of bond wires allow the 10 Ld DFN to have a higher current capability than either the 8 Ld SOIC or the DFN.
TABLE 1. ISL61851EVAL1Z TEST POINT ASSIGNMENTS
TP NAME DESCRIPTION
GND Eval Board and IC Gnd
V+ Eval Board and IC Bias
EN1 Enable Switch 1
EN2 Enable Switch 2
FLT2 Switch 2 Fault
OUT2 Switch Out 2
OUT1 Switch Out 1
FLT1 Switch 1 Fault
TABLE 2. ISL6185XEVAL1Z BOARD COMPONENT LISTING
COMPONENTDESIGNATOR
COMPONENT FUNCTION COMPONENT DESCRIPTION
U1 ISL6185 Intersil, ISL6185
R3 - R4 Output Load Resistors
105%, 3W
R1 - R2 FLT Output Pull-up Resistor
10k, 0805
C1 Decoupling Capacitor
2.2µF, 0805
C2 - C3 Load Capacitor 10µF 16V Electrolytic, Radial Lead
ProductsIntersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information pages on intersil.com for ISL6185XXC (commercial version) and ISL6185XXI (industrial version).
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/sear
Revision HistoryThe revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev.
DATE REVISION CHANGE
March 1, 2012 FN6937.3 In “Features” on page 1 changed from:UL Recognized, File Number: E333469(Applies to DFN Packages, SOIC Package to be Qualified Shortly)to:UL Recognized, File Number : E333469
In “Absolute Maximum Ratings” on page 6:Changed from:Output Current . . . . . . . . . Short Circuit Protectedto:Output Current . . . . . . . . . .Short Circuit Protected Current Limit of 2.5A
Updated “Package Outline Drawing” on page 20. Changed Note 1 "1982" to "1994".
December 2, 2011 FN6937.2 Page 1: Added "UL Recognized, File Number: E333469 (Applies to DFN packages, SOIC pkg to be qualified shortly)" to "Features"Page 8: Added Isc_5.5, Short Circuit Current with max of 2.5A to “Electrical Specifications”Page 19: Updated package outline drawing to most updated revision. Removed package outline and included center to center distance between lands on recommended land pattern. Removed Note 4 "Dimension b applies to the metallized terminal and is measured between 0.18mm and 0.30mm from the terminal tip." since it is not applicable to this package. Renumbered notes accordingly.
June 14, 2011 FN6937.1 Page 2: “Ordering Information”: added part numbers of parts installed on evaluation boards to Description column.Page 7: “Electrical Specifications” table:- For “Maximum Continuous Current, VIN = 2.5V,” changed “ISL61851C,D,G,H (SOIC)” to “ISL61851C,D,G,H,I,J,K,L (SOIC)”- For “Trip Current, VIN = 5V”, changed “ISL61853I,J,K,L” to “ISL6185xI,J,K,L”. For “ISL61853M.N,O,P” changed MAX from “2.15” to “2.45”.- For “Trip Current, VIN = 3.3V” and “Trip Current, VIN = 2.5V” changed “ISL61853I,J,K,L“ to “ISL6185xI,J,K,L“.- For “Current Limit, VIN = 5V”, “Current Limit, VIN = 3.3V”, and “Current Limit, VIN = 2.5V”, changed “ISL61853I,J,K,L, VIN - VOUT = 1V” to “ISL6185xI,J,K,L, VIN - VOUT = 1V”- For “Short Circuit Current, VIN = 5V”, “Short Circuit Current, VIN = 3.3V” and “Short Circuit Current, VIN = 2.5V” changed “ISL61853I,J,K,L, VOUT = 0V” to “ISL6185xI,J,K,L, VOUT = 0V”Page 8: “Electrical Specifications” table: For the I/O Parameters Venr_5, Hys_Venr_5, Venr_3, Hys_Venr_3, Venr_2, and Hys_Venr_2: changed "ENABLE Rising Threshold" and "ENABLE Rising Threshold Hysteresis" to "EN / EN Rising Threshold" and "EN / EN Rising Threshold Hysteresis," for clarity.Page 8: Electrical Specifications table: Removed UVHYS, POR Hysteresis specification.Page 20: Replaced Rev. 1 of M8.15 package outline drawing, dated 6/05, with Rev 2 (latest version), dated 11/10.Applied current Intersil datasheet template to document.