IS8000 Integrated Software Installation Manual - Yokogawa

User’sManual IS8000

Integrated SoftwareInstallation Manual

IM IS8000-04EN7th Edition

User RegistrationYOKOGAWA provides registered users with useful information and services. Please allow us to serve you best by completing the user registration form accessible from our website.

https://tmi.yokogawa.com/support/

Contact UsIf you want to resolve a technical support issue or need to contact YOKOGAWA, please fill out the inquiry form on our website.

https://tmi.yokogawa.com/contact/

PIM 103-06E

iIM IS8000-04EN

Thank you for purchasing the IS8000 Integrated Software (hereinafter referred to as the IS8000 Software). This installation manual mainly explains how to install and activate the IS8000 Software.* To ensure correct use, please read this manual thoroughly before operation.

* Activation is an act of authenticating the license for the software you purchased in order to use the features of the software on your personal computer (PC).

After reading this manual, keep it in a safe place. This software comes with various manuals that are listed under “Manuals” in the User’s Manual (IM IS8000-01EN). Please read all manuals.

You can open the above manuals from the launcher and Help menu of this software. For details on the procedures, see section 9.3 in the User’s Manual, IM IS8000-01EN.

Contact information of Yokogawa offices worldwide is provided on the following sheet.Document No. DescriptionPIM 113-01Z2 List of worldwide contacts

Notes• The contents of this manual are subject to change without prior notice as a result of continuing

improvements to the product’s performance and functionality. The figures given in this manual may differ from those that actually appear on your product.

• Every effort has been made in the preparation of this manual to ensure the accuracy of its contents. However, should you have any questions or find any errors, please contact your nearest YOKOGAWA dealer.

• Copying or reproducing all or any part of the contents of this manual without the permission of YOKOGAWA is strictly prohibited.

• The license management section of this licensee application is based on one or more of the following copyrights:Sentinel® RMS © 2005 SafeNet, Inc. All rights reserved.Sentinel® EMS © 2009 SafeNet, Inc. All rights reserved.

Trademarks• Microsoft, Internet Explorer, Windows, and Windows 10 are registered trademarks or trademarks

of Microsoft Corporation in the United States and/or other countries.• Adobe and Acrobat are either registered trademarks or trademarks of Adobe Systems

Incorporated.• Sentinel is a registered trademark of SafeNet, Inc.• In this manual, the ® and TM symbols do not accompany their respective registered trademark

or trademark names.• Other company and product names are trademarks or registered trademarks of their respective

holders.

7th Edition: June 2022 (YMI)All Rights Reserved, Copyright © 2021 Yokogawa Test & Measurement Corporation

ii IM IS8000-04EN

Revisions • 1st Edition: March 2021 • 2nd Edition: May 2021 • 3rd Edition: July 2021 • 4th Edition: September 2021 • 5th Edition: January 2022 • 6th Edition: March 2022 • 7th Edition: June 2022

Updating the SoftwareIt is recommended to update the software to the latest version to improve the features and usability of this software.Download the latest software from the YOKOGAWA website, or contact your nearest YOKOGAWA dealer for details.

iiiIM IS8000-04EN

Conventions Used in This Manual

Prefixes k and KThis manual distinguishes prefixes k and K used before units as follows:

k: Denotes 1000. Example: 100 kS/s (sample rate)K: Denotes 1024. Example: 720 KB (file size)

Displayed CharactersBold alphanumeric characters in procedural explanations indicate characters that appear in the menus on the screen.

NotesThis manual uses the following symbol to indicate notes.

Note Calls attention to information that is important for the proper operation of the software.

iv IM IS8000-04EN

Check the Following before Use

Check the following information. If the wrong items have been delivered or if items are missing, contact your nearest YOKOGAWA dealer.

Inquiries(PIM 113-01Z2) 1 sheet

Product Information(PI IS8000-01)1 sheet

Product InformationThe following items are indicated. Please keep this sheet in a safe place.• Model name and suffix code of the software• License code

You need to enter this license code the first time you start the software.• Download page URL

You can download the software from this URL.

MODEL Suffix Code Description Notes

IS8000 Integrated SoftwareIS8001 IS8000 Integrated Software Subscription Platform

Annual LicenseIS8002 IS8000 Integrated Software Perpetual Platform

Permanent LicenseOptions /SY1 Multi-Unit Synchronization Option

/MH1 Waveform Math Option User-defined math function/RP1 Report Generator Option/FS1 High-speed Camera Synchronization Option Synchronized measurement with a

Photron high-speed camera/EM1 ECU Monitor Synchronization Option Synchronized measurement with a DTS

INSIGHT RAMScope

IS8000 Add-on PackagesIS8001EX IS8000 Add-on Package Subscription Add-on Package

Annual LicenseIS8002EX IS8000 Add-on Package Perpetual Add-on Package

Permanent License-SY1 Multi-Unit Synchronization-MH1 Waveform Math User-defined math function-RP1 Report Generator-FS1 High-speed Camera Synchronization Synchronized measurement with a

Photron high-speed camera-EM1 ECU Monitor Synchronization Synchronized measurement with a DTS

INSIGHT RAMScope

Harmonic/Flicker SoftwareIS8011 Harmonic/Flicker Software Subscription IEC Software

Annual LicenseIS8012 Harmonic/Flicker Software Perpetual IEC Software

Permanent License

vIM IS8000-04EN

License ModelsAnnual LicenseThis is a license for regular use. You can use the latest software at all times during the period of use. If you want to continue using the software after the period of use, you need to repurchase the license.

Permanent LicenseThis is a one-time purchase version. You can upgrade the software during the year the software was shipped and for five years from the year following the year the software was shipped. (See the figure below.)You can continue to use the software in the same environment even after the version upgrade deadline has passed.*

* If you updated your PC’s operating system or the measuring instrument firmware, YOKOGAWA cannot guarantee the operation.

(year)

Base license code

2021 2022 2023 2024 2025 2026 2027

Reception

Shipment

Example When You Purchase a Permanent License in 2021

Activation Upgrade expiration date

Can be upgraded to the latest software version5 years or more

Can be used indefinitely from activationIS8002

The final 2026 version can be used indefinitely.

If the shipment year is 2021, upgrading is possible until 2026. From 2027, you cannot upgrade the software, but you can continue to use the version before 2026.

For details on the license period and renewal, see section 9.6 in the User’s Manual, IM IS8000-01EN.

ManualsThe following user’s manuals are contained in the downloaded software.Manual Title Manual No.IS8000 Integrated Software User’s Manual IM IS8000-01ENIS8000 Integrated Software Installation Manual IM IS8000-04ENIS8000 Integrated Software High-speed Camera Synchronization Option User’s Manual

IM IS8000-61EN

IS8000 Integrated Software ECU Monitor Synchronization Option User’s Manual

IM IS8000-62EN

Harmonic/Flicker Software User’s Manual IM IS8000-63EN

To view the PDF data, you need Adobe Acrobat Reader or a software application that can open PDF data.

Check the Following before Use

vi IM IS8000-04EN

Notes on Usage

Notes on Using the Software• This software can be used on two PCs per license. It can be used on two PCs simultaneously.

For details on the license period and renewal, see section 9.6 in the User’s Manual, IM IS8000-01EN.)

• To allow communication between a measuring instrument (SC, DLM, WT series) and a PC through its USB interface, you need to install a USB driver in the PC.You can download the USB driver from the following web page:

https://tmi.yokogawa.com/library/

• Only a single measuring instrument can be controlled by this software. If you are using the multi-unit synchronization measurement feature (SY1 option), up to five measuring instruments can be connected to a PC and controlled by this software.

• When you connect a measuring instrument to a PC and use the software to control the measuring instrument, you cannot use multiple types of communication interface at the same time.

• Do not perform panel operations on the measuring instrument that you are controlling with this software. Doing so may cause errors.

• The software may not be able to continue if the PC enters standby or hibernation mode. Disable standby and hibernation modes when you use the software.

• If a connection error occurs, turn off the measuring instrument and then turn it back on.

Feature RestrictionsSoftware TrialIf you click “Trial Version” during license activation, you will be able use all the features of the software for 30 days.

Simple EditionThe software switches to the Simple Edition (with restrictions on some features) in the following cases.For details on restricted features, see the table on the next page.

• If 30 days have passed since you started to use the trial version without activating the license.Enter your license code, and activate your license (see chapter 2). Activated features will become available.

• When the annual license has expiredA message will appear when you start the software if the subscription is to expire within 3 months. If you want to continue using the software, contact your nearest YOKOGAWA dealer before the expiration date. * The start of the period of use will be when the activation of the software is completed.

viiIM IS8000-04EN

Restricted FeaturesThe use of the following features is restricted on the Simple Edition.

Standard featuresFeature Restricted Item DescriptionOnline monitor DAQ from the launcher Disabled

Remote control from the data source * WT5000: Monitoring up to eight items on a single unit

DAQ (data acquisition)

Contents on the Control tab DisabledWizard save settings * WT5000: Recording up to eight items on a

single unitWT5000 data streaming waveform measurements Disabled

Remote control Remote control from the launcher DisabledRemote control from the data source * Only a single WT5000 can be controlled.

* XWirepuller (free version) can be started.File management File Manager from the launcher

DisabledRemote control from the data source

Basic features Channel display group One group onlyMaximum number of channels per display group 8CHView display One view panel onlyXY Display One XY panel onlyPower numeric display One numeric panel (4-value display or 8-value

display) onlyHarmonic bar graph display One bar panel (one item) onlyAnnotation feature DisabledFile saving Only waveform files (CSV) can be saved.

Multiple files Add files on the File tabDisabledCoaxial start/stop of data source

CSV batch converter on the APPs tabMeasurement Measurement on the Analysis tab Disabled

Multi-Unit Synchronization Feature (SY1 option)Multi-unit connection Additional connection when one unit is

connectedDisabled* Multi-unit startup of this software is possible.

Waveform Math Feature (MH1 option)Math Math settings on the Analysis tab

DisabledFFT FFT settings on the FFT View tab

Report Generator Feature (RP1 option)Report Report on the APPs tab Disabled

High-speed Camera Synchronization Feature (FS1 option)High-speed camera Camera search Disabled

* Not detectedContents on the Video tab

ECU Monitor Synchronization Feature (EM1 option)ECU monitor RAMScope search Disabled

* Not detected

Harmonic/Flicker SoftwareIEC 61000 IEC 61000 from the launcher

DisabledIEC 61000 on the APPs tab

• For details on each feature, see the User’s Manual, IM IS8000-01EN.• For the target instruments of each feature, see pagepage 1-2.

Notes on Usage

viii IM IS8000-04EN

Preparation

When Activating with a PC Connected to the Internet (Online PC)Follow the procedure below to activate the license online.

* After the activation is complete, you can use the software without an Internet connection.

Download Download the software file from YOKOGAWA website. See section 1.2.

Installation Install the software on the online PC. See section 1.2.

First startup • In the startup window, select activation.See sections 2.1, 2.2.• On the activation screen, enter the license code, and click Activate.

→ License activation complete

Begin use The activation screen will not appear the next time you start the software.

When Activating with a PC Not Connected to the Internet (Offline PC)Follow the procedure below to activate the license offline.

* Use an online PC to download the software and create a license file.

Online PC Offline PCDownload ─ Download the software file from YOKOGAWA website. See section 1.2.

Installation Install the software on the offline PC. See section 1.2.

First startup • In the startup window, select activation.

See sections 2.1, 2.3.

• On the activation screen, enter the license code, and click Obtain PC information.

→ A zip file containing the license code, PC information, and activation tool is created.

License file creation

─ • Copy the zip file to the online PC, and unzip it.

See page 2-6.• Start the activation tool.• Select the location where you want to save the license file, and

click OK.→ A license file is created.

Select the license file

• On the offline PC’s activation screen, select the license file.See page 2-6.• Click OK.

→ License activation complete

Begin use The activation screen will not appear the next time you start the software.

ixIM IS8000-04EN

NoteTrying All the Features of the SoftwareIn the startup window, select to start using the trial software. You do not need to enter the license code.

When Using a Single License on two PCsAfter completing the activation on the first PC, perform activation on the second PC using the same license code as the first.

Viewing and Managing the License Information after Beginning UseOn the Help menu, click License to view the license information view screen.► Section 9.5 in the User’s Manual (IM IS8000-01EN)

Preparation

x IM IS8000-04EN

Terms and Conditions of the Software License

Yokogawa Test & Measurement Corporation, a Japanese corporation (hereinafter called “Yokogawa”), grants permission to use this Yokogawa Software Program (hereinafter called the “Licensed Software”) to the Licensee on the conditions that the Licensee agrees to the terms and conditions stipulated in Article 1 hereof. You, as the Licensee (hereinafter called “Licensee”), shall agree to the following terms and conditions for the software license (hereinafter called the “Agreement”) based on the use intended for the Licensed Software. Please note that Yokogawa grants the Licensee permission to use the Licensed Software under the terms and conditions herein and in no event shall Yokogawa intend to sell or transfer the Licensed Software to the Licensee. Product: IS8000 Integrated Software Number of Client License: 1 Number of Computers That Can Be Used 2

Article 1 (Scope Covered by these Terms and Conditions)1. The terms and conditions stipulated herein shall be applied to any Licensee who purchases the Licensed Software on the condition that the

Licensee consents to agree to the terms and conditions stipulated herein.2. The “Licensed Software” herein shall mean and include all applicable programs and documentation, without limitation, all proprietary technology,

algorithms, and know-how such as a factor, invariant or process contained therein.

Article 2 (Grant of License)1. Yokogawa grants the Licensee, for the purpose of single use, during the period of use, non-exclusive and non-transferable license of the

Licensed Software with the license fee separately agreed upon by both parties. Yokogawa allows the Licensee to use only one instance of the software for use on one device, whether that device is physical or virtual. If the

Licensee want to use the software on more than one virtual device, the Licensee must obtain a separate Licensed Software for each instance.2. The Licensee shall not copy, change, sell, distribute, transfer, or sublicense the Licensed Software without a prior notice to Yokogawa and

Yokogawa’s consent.3. In no event shall the Licensee dump, reverse assemble, reverse compile, or reverse engineer the Licensed Software so that the Licensee may

translate the Licensed Software into other programs or change it into a man-readable form from the source code of the Licensed Software. Unless otherwise separately agreed by Yokogawa, Yokogawa shall not provide the Licensee the source code for the Licensed Software.

4. The Licensed Software and its related documentation shall be the proprietary property or trade secret of Yokogawa or a third party which grants Yokogawa the rights (hereinafter called the “Third Party”). In no event shall the Licensee be transferred, leased, sublicensed, or assigned any rights relating to the Licensed Software.

5. Yokogawa may use or add a license authentication mechanism (activation function) that enables a computer to use the Licensed Software. In no event shall the Licensee remove, bypass, or attempt to remove or bypass such activation function.

6. The Licensed Software includes a software program licensed for re-use by the Third Party (hereinafter called “Third Party Software”, which may include any software program from affiliates of Yokogawa made or coded by themselves.) The Licensee shall observe the following terms and conditions regarding the Third Party Software.

• The Licensee shall not delete Yokogawa’s or the Third Party’s copyright notices, trademark notices, or other proprietary notices from the Licensed Software or its related materials, or falsify them in any way.

• The Licensee agree that, when the Licensee activates the Licensed Software, the Third Party will access an instance of the activation function and will use the transaction and system data acquired by the Third Party for the purpose of improving functions, improving quality, and obtaining the usage status. The Licensee also agrees that such data belong to the Third Party.

7. Yokogawa software products may contain open source software (hereafter referred to as OSS). For the OSS, terms and conditions provided separately apply with higher precedence than those of this agreement.

Article 3 (Restriction of Specific Use)1. The Licensed Software shall not be intended specifically to be designed, developed, constructed, manufactured, distributed or maintained for

the purpose of the following events: a) Operation of any aviation, vessel, or support of those operations from the ground; b) Operation of nuclear products and/or facilities; c) Operation of nuclear weapons and/or chemical weapons and/or biological weapons; or d) Operation of medical instrumentation directly utilized for humankind or the human body.2. Even if the Licensee uses the Licensed Software for the purposes in the preceding Paragraph 3.1, Yokogawa has no liability to or responsibility

for any demand or damage arising out of the use or operations of the Licensed Software, and the Licensee agrees, on its own responsibility, to solve and settle the claims and damages and to defend, indemnify or hold Yokogawa totally harmless, from or against any liabilities, losses, damages and expenses (including fees for recalling the Products and reasonable attorney’s fees and court costs), or claims arising out of and related to the above-said claims and damages.

Article 4 (Warranty)1. If the activation function of the Licensed Software does not work properly, Yokogawa will reissue the license number free of charge for seven (7)

days after the first activation. Except for the malfunction of the first activation, the Licensed Software is provided “as-is,” and Yokogawa shall not be held responsible for any other warranty liability or default liability under any circumstances. Yokogawa is not liable for any damages caused by vulnerabilities in the Licensed Software (including, but not limited to, damages caused by attacks through computer viruses or unauthorized computer access that takes advantage of software vulnerabilities) or any damages caused by the customer’s environment (software, hardware, or other media).

2. When Yokogawa decides in its own judgment that it is necessary, Yokogawa may from time to time provide the Licensee with Revision upgrades and Version upgrades separately specified by Yokogawa (hereinafter called “Updates”).

3. Notwithstanding the preceding Paragraph 4.3, in no event shall Yokogawa provide Updates where the Licensee or any third party conducted renovation or improvement of the Licensed Software.

xiIM IS8000-04EN

Article 5 (Infringement)1. If and when any third party should demand injunction, initiate a law suit, or demand compensation for damages against the Licensee under

patent right (including utility model right, design patent, and trade mark), copy right, and any other rights relating to any of the Licensed Software, the Licensee shall notify Yokogawa in writing to that effect without delay.

2. In the case of the preceding Paragraph 5.1, the Licensee shall assign to Yokogawa all of the rights to defend the Licensee and to negotiate with the claiming party. Furthermore, the Licensee shall provide Yokogawa with necessary information or any other assistance for Yokogawa’s defense and negotiation. If and when such a claim should be attributable to Yokogawa, subject to the written notice to Yokogawa stated in the preceding Paragraph 5.1, Yokogawa shall defend the Licensee and negotiate with the claiming party at Yokogawa’s cost and expense and be responsible for the final settlement or judgment granted to the claiming party in the preceding Paragraph 5.1.

3. When any assertion or allegation of the infringement of the third party’s rights defined in Paragraph 5.1 is made, or when at Yokogawa’s judgment there is possibility of such assertion or allegation, Yokogawa will, at its own discretion, take any of the following countermeasures at Yokogawa’s cost and expense.

a) To acquire the necessary right from a third party which has lawful ownership of the right so that the Licensee will be able to continue to use the Licensed Software;

b) To replace the Licensed Software with an alternative one which avoids the infringement; or c) To remodel the Licensed Software so that the Licensed Software can avoid the infringement of such third party’s right.4. If and when Yokogawa fails to take either of the countermeasures as set forth in the preceding subparagraphs of Paragraph 5.3, Yokogawa

shall indemnify the Licensee only by paying back the price amount of the Licensed Software which Yokogawa has received from the Licensee. THE FOREGOING PARAGRAPHS STATE THE ENTIRE LIABILITY OF YOKOGAWA AND ANY THIRD PARTY LICENSING THIRD PARTY SOFTWARE TO YOKOGAWA WITH RESPECT TO INFRINGEMENT OF THE INTELLECTUAL PROPERTY RIGHTS INCLUDING BUT NOT LIMITED TO, PATENT AND COPYRIGHT.

5. Regardless of this article, the terms and conditions provided separately apply to demands for compensation or the like arising from the use of OSS.

Article 6 (Liabilities)If and when the Licensee should incur any damage relating to or arising out of the Licensed Software or service that Yokogawa has provided to the Licensee under the conditions herein due to a reason attributable to Yokogawa, Yokogawa shall take actions in accordance with this Agreement. However, in no event shall Yokogawa be liable or responsible for any special, incidental, consequential and/or indirect damage, whether in contract, warranty, tort, negligence, strict liability, or otherwise, including, without limitation, loss of operational profit or revenue, loss of use of the Licensed Software, or any associated products or equipment, cost of capital, loss or cost of interruption of the Licensee’s business, substitute equipment, facilities or services, downtime costs, delays, and loss of business information, or claims of customers of Licensee or other third parties for such or other damages. Even if Yokogawa is liable or responsible for the damages attributable to Yokogawa and to the extent of this Article 6, Yokogawa’s liability for the Licensee’s damage shall not exceed the price amount of the Licensed Software or service fee which Yokogawa has received. Please note that Yokogawa shall be released or discharged from part or all of the liability under this Agreement if the Licensee modifies, remodels, combines with other software or products, or causes any deviation from the basic specifications or functional specifications, without Yokogawa’s prior written consent.

Article 7 (Assignment of Rights and Obligations)The Licensee may not assign any rights or obligations under this agreement to a third party without Yokogawa’s written consent. If, with Yokogawa’s consent, the Licensee transfers the Licensed Software and the status of this agreement, the Licensee shall transfer the entire Licensed Software to the transferee and completely erase any copies the Licensee holds.

Article 8 (Limit of Export) Unless otherwise agreed by Yokogawa, the Licensee shall not directly or indirectly export or transfer the Licensed Software to any countries other

than those where Yokogawa permits export in advance.

Article 9 (Term)Except as provided in Article 10, this Agreement shall become effective on the date when the Licensee receives the Licensed Software and continues in effect until the end of the period of use agreed in Paragraph 2.1. However, Paragraph 2.5 and Articles 5, 6, 9, and 12 shall survive even after the termination of this Agreement or termination by Article 11. After the end of the period of use, the Licensee shall immediately stop using the Licensed Software and return or delete the Licensed Software and its copies.

Article 10 (Audit and Injunction for Use)1. Yokogawa can visit and audit the Licensee’s related facilities to the extent reasonable to confirm the Licensee’s compliance with this Agreement.2. During the term of this Agreement, Yokogawa may, at its own discretion, demand injunction against the Licensee in case that Yokogawa deems

that the Licensed Software is used improperly or under severer environments other than those where Yokogawa has first approved, or any other condition which Yokogawa may not permit.

Article 11 (Termination) Yokogawa, at its sole discretion, may terminate this Agreement without any notice or reminder to the Licensee if the Licensee violates or fails to perform this Agreement. In such an event, the Licensee shall immediately stop using the Licensed Software, and the paid usage fee will not be refunded.

Article 12: Court with JurisdictionAny dispute, controversies, or differences between the parties hereto as to interpretation or execution of this Agreement shall be resolved amicably through negotiation between the parties upon the basis of mutual trust. Should the parties fail to agree within ninety (90) days after notice from one of the parties to the other, both parties hereby irrevocably submit to the exclusive jurisdiction of the Tokyo District Court (main office) in Japan for settlement of the dispute.

Article 13 (Change in Agreement)The contents of this contract, contents of this product, specifications of the licensed software, related support and other related services can be changed at Yokogawa’s discretion.

Terms and Conditions of the Software License

xiiiIM IS8000-04EN

Contents

Conventions Used in This Manual ................................................................................................... iiiCheck the Following before Use ...................................................................................................... ivNotes on Usage ...............................................................................................................................viPreparation .................................................................................................................................... viiiTerms and Conditions of the Software License.................................................................................x

Chapter 1 Installation and Uninstallation1.1 PC System Requirements .............................................................................................. 1-11.2 Installation ...................................................................................................................... 1-41.3 Uninstallation .................................................................................................................. 1-7

Chapter 2 Activation2.1 Starting the Software ...................................................................................................... 2-12.2 Online Activation ............................................................................................................ 2-32.3 Offline Activation ............................................................................................................ 2-5

1-1IM IS8000-04EN

Chapter 1

Installation and Uninstallation

1.1 PC System Requirements

PCFor data acquisition with 10 Gb Ethernet connection;CPU

Desktop PC requiredIntel Core i7-1165G7 or later/4 cores (8 threads) or more/4.7 GHz or faster

Amount of memory16 GB or more

Amount of SSD512 GB or more(M.2 slot is recommended, Sequential read/write 3 GB/s or faster)

For data acquisition with 1 Gb Ethernet/USB connection and offline analysis;CPU

Intel Core i5-10210U or later/4 cores (8 threads) or more/4.2 GHz or fasterAmount of memory

8 GB or moreAmount of SSD

256 GB or more(Sequential read/write 400 MB/s or faster)

Operating SystemWindows 10 64-bit

Communication InterfaceUSB (USBTMC, VISA), Ethernet (VXI-11, HiSLIP)

Display, Printer, and MouseDisplay Resolution1366×768 dpi or higher, 100 % zoom

Operating SystemOperating system mentioned above

1-2 IM IS8000-04EN

1.1 PC System Requirements

Target InstrumentsThe target instruments for the main features of the IS8000 Software are as follows.

* For details on the features, see “Product Overview” in the user’s manuals (IM IV8000-01EN, IM IV8000-63EN).

Integrated SoftwareData Acquisition• DL950 ScopeCorder• WT5000 Precision Power Analyzer

Remote Control• DL950 ScopeCorder• DL850/DL850V, DL850E/DL850EV ScopeCorder• DL350 ScopeCorder• DLM5034, DLM5038, DLM5054, DLM5058 Mixed Signal Oscilloscope• DLM3022, DLM3032, DLM3052 Digital Oscilloscope• DLM3024, DLM3034, DLM3054 Mixed Signal Oscilloscope• WT5000 Precision Power Analyzer

Offline File Analysis• DL950 ScopeCorder• DL850/DL850V, DL850E/DL850EV ScopeCorder• DL350 ScopeCorder• SL1000 High-Speed Data Acquisition Unit• DLM5034, DLM5038, DLM5054, DLM5058 Mixed Signal Oscilloscope• DLM4038, DLM4058 Mixed Signal Oscilloscope• DLM3022, DLM3032, DLM3052 Digital Oscilloscope• DLM3024, DLM3034, DLM3054 Mixed Signal Oscilloscope• DLM2022, DLM2032, DLM2052 Digital Oscilloscope• DLM2024, DLM2034, DLM2054 Mixed Signal Oscilloscope• WT5000 Precision Power Analyzer• 760301, 760302, 760303, 760304, WT3001E, WT3002E, WT3003E, WT3004E Precision

Power Analyzer • WT1801, WT1802, WT1803, WT1804, WT1805, WT1806, WT1801E, WT1802E, WT1803E,

WT1804E, WT1805E, WT1806E Precision Power Analyzer

High-speed Camera (/FS1 option)• Photron: FASTCAM SA-Z, FASTCAM Mini AX/UX/WX series, FASTCAM NOVA• The connected instrument is the DL950 ScopeCorder.

ECU Monitor (/EM1 option)• DTS INSIGHT: RAMScope GT122, GT150/GT170 (RAM monitor module only)• The connected instrument is the DL950 ScopeCorder.• Online connection supports a single RAM monitor module

1-3IM IS8000-04EN

1.1 PC System Requirements

Harmonic/Flicker Software• WT5000 Precision Power Analyzer

Power Supply Control Function• NF Corporation: ES2000S, ES2000U, DP4162, DP4163, DP4164, DP4165, DP4166,

DP4167, DP4168, DP4169

1-4 IM IS8000-04EN

1.2 Installation

ProcedureBefore installing the IS8000 Software, close all programs that are currently running.

NoteA dialog box regarding administrator privileges may appear during the installation. If this appears, follow the message in the dialog box.

Downloading the Software1. Turn on a PC connected to the Internet to start Windows.

2. Download the software from the URL indicated on the Product Information sheet to a location of your choice in your PC.* For details on the Product Information sheet, see page iv.

When Installing to an Online PC Proceed to step 4.

When Installing to an Offline PC3. Using a USB memory device or another storage device, move or copy the software to a

location of your choice on a PC not connected to the Internet.

4. Unzip the software.

5. Double-click Setup.exe in the unzipped folder.

6. If the “User Account Control” window appears, click Allow or Yes to continue the installation. The installer starts. Follow the instructions on the window, and then click Next.

1-5IM IS8000-04EN

1.2 Installation

7. Click I accept the terms in the license agreement, and click Next. If you click I do not accept the terms in the license agreement, the installation will be

canceled.

8. A window appears for you to enter user information. Enter your user name and affiliation, and click Next.

9. A window for setting the installation destination appears. The default destination is C:¥Program Files¥Yokogawa¥IS8000¥. To change the destination,

click Change and select the desired directory.

Check the installation destination, and click Next.

10. A window appears prompting you to start the installation. If there is no problem with the installation settings, click Install.

Click Back if you want to change the installation destination. Click Cancel to cancel the installation.

1-6 IM IS8000-04EN

1.2 Installation

When the software installation finishes normally, the following window appears.

11. Click Finish to complete the installation. IS8000 is added to the Windows Start menu, and a shortcut icon is created on the desktop.

NoteAfter the installation finishes, a Program Compatibility Assistant window may appear. The installation has been completed successfully, so select This program installed correctly or Cancel to close the window.

Explanation

USB DriverTo allow communication between a measuring instrument (SC, DLM, WT series) and a PC through its USB interface, you need a dedicated USB driver (YTUSB or YKMUSB) or IVI driver (VISA).You can download the latest dedicated USB driver from the following web page:

http://tmi.yokogawa.com/service-support/downloads/

YTUSB DriverSupported instruments: DL950, DLM3000, DLM5000, WT5000, etc.Run Setup.exe in the YTUSB folder. The installation wizard starts. For details on the installation procedure, see the manual (ReadMe_en.pdf) in the YTUSB folder.

YKMUSB DriverSupported instruments: DL350, DL850/DL850V, DL850E/DL850EV, etc.Run Setup.exe in the YKMUSB folder. The installation wizard starts. For details on the installation procedure, download “YKMUSB USB Driver Installation Procedure (IM B9852UT-01E)” from the Web page above, and view the instructions.

1-7IM IS8000-04EN

1.3 Uninstallation

NoteIf you want to uninstall the software to exchange the PC, for example, deactivate the software first.For details on deactivation, see section 9.5 in the User’s Manual (IM IS8000-01EN).

Procedure

1. Click (Start) and then (Setup). The Windows setup window appears.2. In the Windows setup window, select Apps. The Apps window appears.

3. From the items on the left side of the window, select Apps and Features.

Uninstalling the IS8000 Software4. From the list displayed on the right side of the window, select IS8000, and click Uninstall. A window appears for confirming the uninstallation of the selected app and related information.

5. Click Uninstall.

6. If the “User Account Control” window appears, click Allow or Yes to continue the installation. The IS8000 software will be uninstalld.

Uninstalling the USB DriverYTUSB Driver4. From the list displayed on the right side of the screen, select Windows driver package and

then Yokogawa Test & Measurement Corporation (WinUSB) YTUSB (mm/dd/yyyy x.x.x.x), and click Uninstall.

YKMUSB Driver4. From the list displayed on the right side of the window, select YKMUSB64, and click Uninstall.

The uninstallation will proceed in a similar manner as the IS8000 Software described above.

2-1IM IS8000-04EN

Chapter 2

Activation

This chapter explains how to activate the IS8000 Software you purchased so that you can use the software features on your PC.

2.1 Starting the Software

Procedure

1. You can start the software using one of the following two methods.• Double-click the shortcut icon on the desktop.

Shortcut icon

• Click Windows (Start) > YOKOGAWA > IS8000.

Start menu

When you start the software for the first time, a start window appears

2. In the startup window, click Activation.

Closes the window (IS8000 software)

Starts the trial of all features

Trial period (displayed only during the trial period)

Activates the license

An online activation or offline activation window appears depending on whether an Internet connection is available.

2-2 IM IS8000-04EN

2.1 Starting the Software

Explanation

Startup WindowThis window appears the first time you start the software.* Select either of the following:

* The window appears every time you start the software during the trial period.

Activation• When the software is running on a PC connected to the Internet

An online activation window appears.► section 2.2

• When the software is running on a PC not connected to the InternetAn offline activation window appears.► section 2.3

Start TrialClick this button to start a trial of the software.If the trial period expires after starting the trial, this button will be disabled.

Trial Period DisplayWhen you start the software during the trial period, the trial period is displayed in the window.• Display Example

Trial period: 2021/04/02

Trial (Software Trial)You can try out all the features before activation.

Trial PeriodThe trial period is 30 consecutive days after starting the trial the first time.

Even if you activate the product in the middle of a trial period, the trial period continues until the expiration date. If the product license expires after the trial period has expired, the Simple Edition is activated, and the trial period will not be revived.

2-3IM IS8000-04EN

2.2 Online Activation

This section explains how to activate the software using a PC connected to the Internet.After the activation is complete, you can use the software without an Internet connection.

Procedure1. Refer to section 2.1, and start the software on an online PC. In the startup window, click Activation. An activation window opens.

2. Enter the license code, and click Activate. The license code is indicated on the Product Information sheet.

Enter all 36 digits of the license code. The Activate button becomes available.

Enter or view the license code.

The product information window appears.The license code and license model of the software to be activated are displayed in the window.

3. Check the displayed information, and click OK. When the license is activated, a message appears indicating the successful activation.

2-4 IM IS8000-04EN

2.2 Online Activation

4. Click OK to close the message window. When the activation is completed, the launcher is displayed.

NoteIf you enter a wrong license code, an activation failure message will appear.If this occurs, click OK, and enter the license code again in the activation window.

Base license codeThe license code that has completed activation first is called the base license code. License information from this point is managed by the base license code including when licenses are added or updated as a result of adding add-on packages.

Adding or Updating the LicenseAfter the first activation, if you add options, you will need to add or update the license and activate it.To do so, on the Help menu, click License to open the license information view window.

► Section 9.5 in the User’s Manual (IM IS8000-01EN)

NoteWhen Adding or Updating a Single License on two PCs

• When the first PC has been activated but the software is used for the first time on the second PC After adding or updating the license and completing the activation on the first PC, perform the first

activation on the second PC using the same license code as the first.

• When the first activation has been completed on both PCs After adding or updating the license and completing the activation on the first PC, update the license in

the License Information window on the second PC. The license information of the first PC is copied to the second PC.

After starting the software on the second PC, click Update in the license information display window. Details of the procedure ► Section 9.5 in the User’s Manual (IM IS8000-01EN)

2-5IM IS8000-04EN

2.3 Offline Activation

This section explains how to activate the software using a PC not connected to the Internet. If you want to use the software on a PC that cannot be connected to the Internet, use this method to activate it.

NoteThe license file described in steps 6 to 9 is created using an activation tool on a PC connected to the Internet.

Procedure1. Refer to section 2.1, and start the software on an offline PC. In the startup window, click Activation. An activation window opens.

2. Enter the license code, and click Execute. The license code is indicated on the Product Information sheet. Enter all 36 digits of the license code. The Activate button becomes available.

Enter or view the license code.

Activate the trial version.

A zip file is created. This file contains the license code, PC information, and activation tool. A Save As dialog box appears.

3. Click OK. A Save As dialog box appears

2-6 IM IS8000-04EN

2.3 Offline Activation

Obtaining PC Information4. Specify the location to save the zip file.

5. Click OK. Leave the activation window as it is, and proceed to the next step.

Creating a License File on an Online PC6. Copy the zip file to a location of your choice in the online PC and unzip the file.

7. Start the activation tool (ActivationTool.exe). The license activation will begin. The license code and PC information are created automatically.

8. When the license activation is completed, the license code and license model of the software to be activated are displayed in the window.

9. Check the displayed information, and click OK. A license file is created and automatically saved

Selecting the License File on the Offline PC10. Copy the license file to a location of your choice on the offline PC.

11. On the offline PC’s activation screen, click Select, and specify the location of the license file saved in step 10.

12. Click OK. The license file will be stored in the offline PC.

13. Start the software. When the activation is completed, the launcher is displayed.

NoteIf you enter a wrong license code, an activation failure message will appear. If this occurs, click OK, and enter the license code again in the activation window.

Base license codeThe license code that has completed activation first is called the base license code. From this point, even if you add add-on packages, license information will be managed by the base license code.

Adding or Updating the License►See “Adding or Updating the License” on page 2-4.