Is Code for Steel

STEELNumber of Records Found -- 994

Standard Description

SP 6 : Part 1 : 1964 Handbook for structural engineers - Structural steel sections

SP 6 : Part 2 : 1962 Handbook For Structural Engineers - 2 : Steel Beams and Plate Girders

SP 6 : Part 3 : 1962 Handbook Structural Engineers - Part 3 : Steel Columns and Struts

SP 6 : Part 5 : 1980 Handbook for structural engineers - Cold-formed, light gauge steel structures

SP 6 : Part 5 : 1980 Handbook for structural engineers - Cold-formed, light gauge steel structures

SP 6 : Part 6 : 1972 Handbook for structural engineers - Application of plastic theory in design of steel structures

SP 14 : 1976 Index to Steel Designations

SP 17 : 1979 Index to IS 1956 Glossary of Terms Relating to Iron and Steel

SP 38 (S and T) : 1987 Handbook of Typified Designs for Structures with Steel Roof Trusses (with and without Cranes) (Based on is Codes)

SP 40 (S and T) : 1987 Handbook on Structures with Steel Portal Frames

SP 47 (S and T) : 1988 Handbook on Structures with Steel Lattice Portal Frames (Without Cranes)

IS 228 : Part 1 : 1987 Methods of chemical analysis of steels: Part 1 Determination of carbon by volumetric method (for carbon 0.05 to 2.50 percent)

IS 228 : Part 2 : 1987 Methods for Chemical Analysis of Steels - Part 2 : Determination of Manganese in Plain-Carbon and Low Alloy Steels by Arsenite Method

IS 228 : Part 3 : 1987 Methods of chemical analysis of steels: Part 3 Determination of phosphorus by alkalimetric method

IS 228 : Part 4 : 1987 Methods of chemical analysis of steels: Part 4 Determination of total carbon by gravimetric method (for carbon greater than or equal to 0.1 percent)

IS 228 : Part 5 : 1987 Methods of chemical analysis of steels: Part 5 Determination of nickel by dimethyl glyoxime (gravimetric) method (for nickel greater than or equal to 0.1 percent

IS 228 : Part 6 : 1987 Methods for Chemical Analysis of Steels - Part 6 : Determination of Chromium by Persulphate Oxidation Method (for Chromium>0.1 Percent)

IS 228 : Part 7 : 1990 Methods of chemical analysis of steels: Part 7 Determination of molybdenum by alpha-benzoinoxime method (for molybdenum 1 percent and not containing tungsten)

IS 228 : Part 8 : 1989 Methods of chemical analysis of steels: Part 8 Determination of silicon by gravimetric method (for silicon 0.05 to 0.50 percent)

IS 228 : Part 9 : 1989 Methods of chemical analysis of steels: Part 9 Determination of sulphur in plain carbon steels by evolution method (for sulphur 0.01 to 0.25 percent)

IS 228 : Part 10 : 1989 Methods of chemical analysis of steels: Part 10 Determination of molybdenum by thiocynate (photometric) method in low and high alloy steels (for molybdenum 0.01 to 1.5 percent)

IS 228 : Part 11 : 1990 Methods of chemical analysis of steels: Part 11 Determination of total silicon by reduced molyddosilicate spectro photo metric method in carbon steels and low alloy steels (for silicon 0.01 to 0.05 percent)

IS 228 : Part 12 : 2001 Methods of Chemical Analysis of Steels - Part 12 : Determination of Manganese by Periodate Spectrophotometric Method in Plain Carbon, Low Alloy and High Alloy Steels (For Manganese 0.01 to 5.0 Percent)

IS 228 : Part XIII : 1982 Methods for Chemical Analysis of Steels - Part XIII : Determination of Arsenic

IS 228 : Part 14 : 1988 Methods of chemical analysis of steels: Part 14 Determination of carbon by thermal conductivity method (for carbon 0.005 to 2.000 percent)

IS 228 : Part 15 : 1992 Methods of chemical analysis of steels: Part 15 Determination of copper by thiosulphate iodide method (for copper 0.05 to 5 percent)

IS 228 : Part 16 : 1992 Methods of chemical analysis of steels: Part 16 Determination of tungsten by spectrophotometric method (for tungsten 0.1 to 2 percent)

IS 228 : Part 17 : 1998 Methods for Chemical Analysis of Steels - Part 17 : Determination of Nitrogen by Thermal Conductivity Method (for Nitrogen up to 0.04 Percent)

IS 228 : Part 18 : 1998 Methods of chemical analysis of steels: Part 18 Determination of oxygen by instrumental method

IS 228 : Part 19 : 1998 Methods of chemical analysis of steels: Part 19 Determination of nitrogen by steam distillation

IS 228 : Part 20 : 2003 Methods for Chemical Analysis of Steels - Part 20 : Determination of Carbon and Sulphur by Infra Red Absorption Method (For Carbon 0.005 to 2 Percent and Sulphur 0.001 to 0.35 Percent)

IS 228 : Part 21 : 2003 Methods for Chemical Analysis of Steels - Part 21 : Determination of Copper by Spectrophotometric Method (For Copper 0.02 to 0.50 Percent)

IS 228 : Part 22 : 2003 Methods of Chemical Analysis of Steels - Part 22 : Determination of Total Hydrogen in Steel by Thermal Conductivity Method (Hydrogen 0.1 ppm to 50 ppm)

IS 228 : Part 23 : 2003 Methods of Chemical Analysis of Steels - Part 23 : Determination of Total Nitrogen in Steel by Optical Emission Spectrometer (Nitrogen 0.002 to 1.0 Percent)

IS 228 : Part 24 : 2003 Methods of Chemical Analysis of Steels - Part 24 : Determination of Nitrogen in Steel by Inert Gas Fusion - Thermal Conductivity Method (Nitrogen 0.001 to 0.2 Percent)

IS 276 : 2000 Austenitic-Manganese Steel Castings - Specification

IS 277 : 2003 Galvanized Steel Sheets, (Plain and Corrugated) - Specification

IS 277 : 1992 Galvanized Steel Sheets (Plain and Corrugated) - Specification

IS 278 : 1978 Specification for Galvanized Steel Barbed Wire for Fencing

IS 278 : 1978 Specification for Galvanized Steel Barbed Wire for Fencing

IS 279 : 1981 Galvanized steel wire for telegraph and telephone purposes

IS 279 : 1981 Galvanized steel wire for telegraph and telephone purposes

IS 280 : 1978 Specification for Mild Steel Wire for General Engineering Purposes

IS 280 : 2006 Mild Steel Wire for General Engineering Purposes

IS 281 : 1991 Mild Steel Sliding Door Bolts for Use with Padlocks - Specification

IS 281 : 1991 Mild Steel Sliding Door Bolts for Use with Padlocks - Specification

IS 398 : Part 2 : 1996 Aluminium conductors for overhead transmission purposes: Part 2 Aluminium conductors, galvanized steel reinforced

IS 398 : Part 2 : 1996 Aluminium conductors for overhead transmission purposes: Part 2 Aluminium conductors, galvanized steel reinforced

IS 398 : Part 3 : 1976 Aluminium conductors for overhead transmission purposes: Part 3 Aluminium conductors, aluminized steel reinforced

IS 398 : Part 3 : 1976 Aluminium conductors for overhead transmission purposes: Part 3 Aluminium conductors, aluminized steel reinforced

IS 398 : Part 5 : 1992 Aluminium conductors for overhead transmission purposes: Part 5 Aluminium conductors - galvanized steel reinforced for extra high voltage (400 kV and above)_

IS 398 : Part 5 : 1992 Aluminium conductors for overhead transmission purposes: Part 5 Aluminium conductors - galvanized steel reinforced for extra high voltage (400 kV and above)_

IS 412 : 1975 Specification for Expanded Metal Steel Sheets for General Purposes

IS 412 : 1975 Specification for Expanded Metal Steel Sheets for General Purposes

IS 432 : Part 1 : 1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part I Mild steel and medium tensile steel bars

IS 432 : Part 1 : 1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part I Mild steel and medium tensile steel bars

IS 432 : Part 2 : 1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part 2 Hard-drawn steel wire

IS 432 : Part 2 : 1982 Specification for mild steel and medium tensile steel bars and hard-drawn steel wire for concrete reinforcement: Part 2 Hard-drawn steel wire

IS 513 : 1994 Cold-rolled low carbon steel sheets and strips

IS 513 : 1994 Cold-rolled low carbon steel sheets and strips

IS 648 : 1994 Non-oriented electrical steel sheets and strips for magnetic circuits

IS 648 : 2006 Cold Rolled Non-Oriented Electrical Steel Sheet and Strip - Fully Processed Type - Specification

IS 649 : 1997 Methods for testing steel sheets for magnetic circuits of power electrical apparatus

IS 649 : 1997 Methods for testing steel sheets for magnetic circuits of power electrical apparatus

IS 723 : 1972 Specification for Steel Countersunk Head Wire Nails

IS 724 : 1964 Specification for Mild Steel and Brass Cup, Ruler and Square Hooks and Screw Eyes

IS 724 : 1964 Specification for Mild Steel and Brass Cup, Ruler and Square Hooks and Screw Eyes

IS 726 : 1982 Galvanized steel buckets for general use - Specification

IS 800 : 2007 General Construction in Steel - Code of Practice

IS 800 : 1984 Code of practice for general construction in steel

IS 801 : 1975 Code of practice for use of cold formed light gauge steel structural members in general building construction

IS 802 : Part 1 : Sec 1 : 1995 Code of practice for use of structural steel in overhead transmission line towers, Part 1 Materials and Loads and permissible stresses Section 1 Materials and Loads

IS 802 : Part 1 : Sec 2 : 1992 Code of practice for use of structural steel in overhead transmission line towers Part 1 : Material, loads and permissible stress Section 2 Permissible stress

IS 802 : Part 1 : Sec 2 : 1992 Code of practice for use of structural steel in overhead transmission line towers Part 1 : Material, loads and permissible stress Section 2 Permissible stress

IS 802 : Part II : 1978 Code of Practice for Use of Structural Steel in Overhead Transmission Line Towers - Part II : Fabrication, Galvanizing, Inspection and Packing

IS 802 : Part II : 1978 Code of Practice for Use of Structural Steel in Overhead Transmission Line Towers - Part II : Fabrication, Galvanizing, Inspection and Packing

IS 802 : Part 3 : 1978 Code of practice for use of structural steel in overhead transmission line towers, part 3 Testing

IS 803 : 1976 Code of Practice for Design Fabrication and Erection of Vertical Mild Steel Cylindrical Welded Oil Storage Tanks

IS 803 : 1976 Code of Practice for Design Fabrication and Erection of Vertical Mild Steel Cylindrical Welded Oil Storage Tanks

IS 804 : 1967 Rectangular pressed steel tanks

IS 804 : 1967 Rectangular pressed steel tanks

IS 805 : 1968 Code of Practice for Use of Steel in Gravity Water Tanks

IS 806 : 1968 Code of practice for use of steel tubes in general building construction

IS 808 : 1989 Dimensions for Hot Rolled Steel Beam, Column, Channel and Angle Sections

IS 808 : 1989 Dimensions for Hot Rolled Steel Beam, Column, Channel and Angle Sections

IS 811 : 1987 Cold formed light gauge structural steel sections

IS 814 : 1991 Covered electrodes for manual metal arc welding of carbon and carbon manganese steel

IS 814 : 2004 Covered Electrodes for Manual Metal Arc Welding of Carbon and Carbon Manganese Steel - Specification

IS 816 : 1969 Code of practice for use of metal arc welding for general construction in mild steel

IS 819 : 1957 Code of Practice for Resistance Spot Welding for Light Assemblies in Mild Steel

IS 841 : 1983 Specification for Steel Hammers

IS 841 : 1983 Specification for Steel Hammers

IS 963 : 1958 Chrome molybdenum steel bars and rods for aircraft purposes

IS 963 : 1958 Chrome molybdenum steel bars and rods for aircraft purposes

IS 990 : 1982 Specification for Spoons, Stainless Steel

IS 990 : 1982 Specification for Spoons, Stainless Steel

IS 992 : 1964 Specification for Forks (Table, Fish, Pastry and Serving), Stainless Steel

IS 1029 : 1970 Hot-rolled steel strip (baling)

IS 1029 : 1970 Hot-rolled steel strip (baling)

IS 1030 : 1998 Carbon steel castings for general engineering purposes

IS 1038 : 1983 Specification for steel doors, windows and ventilators

IS 1038 : 1983 Specification for steel doors, windows and ventilators

IS 1079 : 1994 Hot Rolled Carbon Steel Sheets and Strips - Specification

IS 1149 : 1982 High tensile steel rivet bars for structural purposes

IS 1149 : 1982 High tensile steel rivet bars for structural purposes

IS 1161 : 1998 Steel Tubes for Structural Purposes - Specification

IS 1161 : 1998 Steel Tubes for Structural Purposes - Specification

IS 1173 : 1978 Hot rolled slit steel tee bars

IS 1182 : 1983 Recommended practice for radiographic examination of fusion welded butt joints in steel plates

IS 1200 : Part 8 : 1993 Method of measurement of building and civil engineering work: Part 8 steel work and iron work

IS 1200 : Part 8 : 1993 Method of measurement of building and civil engineering work: Part 8 steel work and iron work

IS 1239 : Part 1 : 1990 Mild steel tubes, tubulars and other wrought steel fittings, Part 1 Mild steel tubes

IS 1239 : Part 1 : 2004 Steel Tubes, Tubulars and Other Wrought Steel Fittings - Specification - Part 1 : Steel Tubes

IS 1239 : Part 2 : 1992 Mild steel tubes, tubulars and other wrought steel fittings, Part 2 Mild steel tubulars and other wrought steel pipe fittings

IS 1239 : Part 2 : 1992 Mild steel tubes, tubulars and other wrought steel fittings, Part 2 Mild steel tubulars and other wrought steel pipe fittings

IS 1252 : 1991 Dimensions of hot rolled steel bulb angles

IS 1253 : 1992 Aluminium for use in iron and steel manufacture

IS 1261 : 1959 Code of practice for seam welding in mild steel

IS 1269 : Part 2 : 1997 Legal metrology - Material measures of length Part 2: Steel tape measures

IS 1280 : 1975 Foundry moulding boxes of steel construction

IS 1323 : 1982 Code of practice for oxy-acetylene welding for structural work in mild steels

IS 1341 : 1992 Specification for steel butt hinges

IS 1361 : 1978 Specification for steel windows for industrial buildings

IS 1361 : 1978 Specification for steel windows for industrial buildings

IS 1367 : Part I : 1980 Technical Supply Conditions for Threaded Steel Fasteners - Part I : Introduction and General Information

IS 1367 : Part 1 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 1 : General Requirements for Bolts, Screws and Studs

IS 1367 : Part II : 1979 Technical Supply Conditions for Threaded Steel Fasteners - Part II : Product Grades and Tolerances

IS 1367 : Part 2 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 2 : Tolerances for Fasteners - Bolts, Screws, Studs and Nuts - Product Grades A, B and C

IS 1367 : Part 3 : 1991 /ISO 898-1 : 1988 Fasteners - Threaded Steel - Technical Supply Conditions - Part 3 : Mechanical Properties and Test Methods for Bolts, Screws and Studs with Full Loadability

IS 1367 : Part 3 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 3 : Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel - Bolts, Screws and Studs

IS 1367 : Part 5 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 5 : Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel - Set Screws and Similar Threaded Fasteners not Under Tensile Stresses

IS 1367 : Part V : 1980 Technical Supply Conditions for Threaded Steel Fasteners - Part V : Mechanical Properties and Test Methods for Set Screws and Similar Threaded Fasteners Not Under Tensile Stresses

IS 1367 : Part 6 : 1994 /ISO 898-2 : 1992 Technical Supply Conditions for Threaded Steel Fasteners - Part 6 : Mechanical Properties and Test Methods for Nuts with Specified Proof Loads

IS 1367 : Part VII : 1980 Technical supply conditions for threaded steel fasteners Part VII Mechanical properties and test methods for nuts without specified proof loads

IS 1367 : Part VII : 1980 Technical supply conditions for threaded steel fasteners Part VII Mechanical properties and test methods for nuts without specified proof loads

IS 1367 : Part 8 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 8 : Prevailing Torque Type Steel Hexagon Nuts - Mechanical and Performance Properties

IS 1367 : Part 8 : 1992 Technical Supply Conditions for Threaded Steel Fasteners - Part 8 : Mechanical and Performance Properties for Prevailing Torque Type Steel Hexagon Nuts

IS 1367 : Part 9 : Sec 1 : 1993/ISO 6157-1 : 1988 Technical supply conditions for threaded steel fasteners Part 9 Surface discontinuities : Section 1 Bolts, screws and studs for general applications

IS 1367 : Part 9 : Sec 1 : 1993/ISO 6157-1 : 1988 Technical supply conditions for threaded steel fasteners Part 9 Surface

discontinuities : Section 1 Bolts, screws and studs for general applications

IS 1367 : Part 9 : Sec 2 : 1993/ISO 6157-3 : 1988 Technical supply conditions for threaded steel fasteners Part 9 Surface discontinuities : Section 2 Bolts, screws and studs for special applications

IS 1367 : Part 9 : Sec 2 : 1993/ISO 6157-3 : 1988 Technical supply conditions for threaded steel fasteners Part 9 Surface discontinuities : Section 2 Bolts, screws and studs for special applications

IS 1367 : Part 10 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 10 : Surface Discontinuities - Nuts

IS 1367 : Part X : 1979 Technical supply conditions for threaded steel fasteners Part X Surface discontinuities on nuts

IS 1367 : Part 11 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 11 : Electroplated Coatings

IS 1367 : Part 11 : 1996 /ISO 4042 : 1989 Technical Supply Conditions for Threaded Steel Fasteners - Part 11 : Electroplated Coatings

IS 1367 : Part XII : 1981 Technical Supply Conditions for Threaded Steel Fasteners - Part XII : Phosphate Coatings on Threaded Fasteners

IS 1367 : Part XIII : 1983 Technical supply conditions for threaded steel fasteners Part XIII Hot-dip galvanized coatings on threaded fasteners

IS 1367 : Part 14 : 1984 Technical Supply Conditions for Threaded Steel Fasteners - Part 14 : Stainless Steel Threaded Fasteners

IS 1367 : Part 14 : 1984 Technical Supply Conditions for Threaded Steel Fasteners - Part 14 : Stainless Steel Threaded Fasteners

IS 1367 : Part 14 : Sec 1 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 14 : Mechanical Properties of Corrosion-Resistant Stainless-Steel Fasteners - Section 1 : Bolts, Screws and Studs

IS 1367 : Part 14 : Sec 2 : 2002 Technical Supply Conditions for - Threaded Steel Fasteners - Part 14 : Mechanical Properties of Corrosion-resistant Stainless-steel Fasteners - Section 2 : Nuts

IS 1367 : Part 14 : Sec 3 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 14 : Mechanical Properties of Corrosion-resistant Stainless-steel Fasteners - Section 3 : Set Screws and Similar Fasteners not Under Tensile Stress

IS 1367 : Part XVI : 1979 Technical Supply Conditions for Threaded Steel Fasteners - Part XVI : Designation System and Symbols

IS 1367 : Part 16 : 2002 Technical Supply Conditions for Threaded Steel Fasteners - Part 16 : Designation System for Fasteners

IS 1367 : Part 17 : 2005 /ISO 3269 : 2000 Technical Supply Conditions for Threaded Steel Fasteners - Part 17 : Inspection, Sampling and Acceptance Procedure

IS 1367 : Part 18 : 1996 Industrial Fasteners - Threaded Steel Fasteners - Technical Supply Conditions - Part 18 : Packaging

IS 1367 : Part 19 : 1997/ISO 3800 : 1993 Industrial fasteners - Threaded steel fasteners - Technical supply conditions Part 19 Axial load fatigue testing of bolts, screws and studs

IS 1367 : Part 20 : 1996 /ISO 898-7 : 1992 Industrial Fasteners - Threaded Steel Fasteners - Technical Supply Conditions - Mechanical Properties - Part 20 : Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1 mm To 10 mm

IS 1395 : 1982 Low and medium alloy steel covered electrodes for manual metal arc welding

IS 1439 : 1990 Steelyards - Specification

IS 1481 : 1970 Specification for Metric Steel Scales for Engineers

IS 1481 : 1970 Specification for Metric Steel Scales for Engineers

IS 1495 : 1970 Specification for mild steel dust-bins

IS 1523 : 1972 Bottom pouring refractories for steel plants

IS 1525 : 1968 Ladle refractories for steel plants

IS 1529 : 1971 Blast furnace refractories for steel plants

IS 1566 : 1982 Specification for Hard-drawn Steel Wire Fabric for Concrete Reinforcement

IS 1566 : 1982 Specification for Hard-drawn Steel Wire Fabric for Concrete Reinforcement

IS 1570 : Part 1 : 1978 Schedules for wrought steels Part 1 Steels specified by tensile and/or yield properties

IS 1570 : Part 1 : 1978 Schedules for wrought steels Part 1 Steels specified by tensile and/or yield properties

IS 1570 : Part II : 1979 Schedules for Wrought Steels - Part II : Carbon Steels (Unalloyed Steels)

IS 1570 : Part 2 : Sec 1 : 1979 Schedules for Wrought Steels - Part 2 : Carbon Steels (Unalloyed Steels) - Section 1 : Wrought Products (Other Than Wires) With Specified Chemical Composition and Related Properties

IS 1570 : Part 2 : Sec 1 : 1979 Schedules for Wrought Steels - Part 2 : Carbon Steels (Unalloyed Steels) - Section 1 : Wrought Products (Other Than Wires) With Specified Chemical Composition and Related Properties

IS 1570 : Part 2 : Sec 2 : 1987 Schedules for Wrought Steels - Part 2 : Carbon Steels (Unalloyed Steels) - Section 2 : Carbon Steel Wires with Related Properties

IS 1570 : Part 3 : 1979 Schedules for wrought steels Part 3 Carbon and carbon manganese free cutting steels

IS 1570 : Part 4 : 1988 Schedules for wrought steels Part 4 Alloy steels (Alloy constructional and spring steels) with specified chemical composition andd mechanical properties

IS 1570 : Part 5 : 1985 Schedules for Wrought Steels - Part 5 : Stainless and Heat-resisting Steels

IS 1570 : Part 6 : 1996 Schedules for Wrought Steels - Part 6 : Carbon and Alloy Tool Steels

IS 1570 : Part 7 : 1992 Schedule for wrought steels Part 7 Steels for elevated temperature service (creep resistant steels)

IS 1572 : 1986 Specification for Electroplated Coatings of Cadmium on Iron and Steel

IS 1573 : 1986 Specification for Electroplated Coatings of Zinc on Iron and Steel

IS 1673 : 1984 Specification for Mild Steel Wire, Cold Heading Quality

IS 1691 : 1980 Specification for Cast Iron and Mild Steel Flat Pulleys

IS 1730 : 1989 Dimensions for steel plates,sheets strips and flats for general engineering purposes

IS 1732 : 1989 Dimensions for round and square steel bars for structural and general engineering purposes

IS 1762 : Part 1 : 1974 Code for designation of steels, Part I Based on lettter symbols

IS 1762 : Part 1 : 1974 Code for designation of steels, Part I Based on lettter symbols

IS 1785 : Part I : 1983 Specification for Plain Hard-drawn Steel Wire for Prestressed Concrete - Part I : Cold Drawn Stress-relieved Wire

IS 1785 : Part I : 1983 Specification for Plain Hard-drawn Steel Wire for Prestressed Concrete - Part I : Cold Drawn Stress-relieved Wire

IS 1785 : Part 2 : 1983 Specification for plain hard-drawn steel wire for prestressed concrete: Part 2 As drawn wire

IS 1785 : Part 2 : 1983 Specification for plain hard-drawn steel wire for prestressed concrete: Part 2 As drawn wire

IS 1786 : 1985 Specification for high strength deformed steel bars and wires for concrete reinforcement (superseding IS:1139-1966)

IS 1786 : 1985 Specification for high strength deformed steel bars and wires for concrete reinforcement (superseding IS:1139-1966)

IS 1804 : 2004 Steel Wire Ropes - Fibre Main Cores - Specification

IS 1804 : 1996 Steel wire ropes - Fibre main cores- Specification

IS 1812 : 1982 Specification for Carbon Steel Wire for the Manufacture of Wood Screws

IS 1829 : Part 2 : 1993 Specification for library furniture and fittings: Part 2 Steel

IS 1835 : 1976 Specification for Round Steel Wire for Ropes

IS 1835 : 1976 Specification for Round Steel Wire for Ropes

IS 1852 : 1985 Rolling and cutting tolerances for hot rolled steel products

IS 1852 : 1985 Rolling and cutting tolerances for hot rolled steel products

IS 1855 : 2003 Stranded Steel Wire Ropes for Winding and Man-Riding Haulages in Mines - Specification

IS 1855 : 1977 Stranded steel wire ropes for winding and man riding haulages in mines

IS 1856 : 2005 Steel Wire Ropes for Haulage Purposes - Specification

IS 1856 : 2005 Steel Wire Ropes for Haulage Purposes - Specification

IS 1863 : 1979 Hot rolled steel bulb flats

IS 1864 : 1979 Hot-rolled steel L-sections for shipbuilding

IS 1870 : 1965 Comparison of Indian and overseas standards for wrought steels for general engineering purposes

IS 1871 : Part 1 : 1987 Commentary on Indian Standard Schedules for Wrought Steels - Part 1 : Steels Specified by Tensile and/or Yield Properties

IS 1871 : Part 2 : 1987 Commentary on Indin Standard Schedules for wrought steels Part 2 Carbon steels (unalloyed steels) (Complementary to IS 1570 Part 2):1979)

IS 1871 : Part 3 : 1987 Commentary on Indian Standard Schedules for Wrought Steels - Part 3 : Carbon and Carbon Manganese Free Cutting Steels

IS 1875 : 1992 Carbon steel billets, blooms, slabs and bars for forgings

IS 1875 : 1992 Carbon steel billets, blooms, slabs and bars for forgings

IS 1914 : Parts I to IV : 1982 Specification for Carbon Steel Boiler Tubes and Superheater Tubes

IS 1914 : Parts I to IV : 1982 Specification for Carbon Steel Boiler Tubes and Superheater Tubes

IS 1916 : 1989 Specification for steel cylinder pipe with concrete lining and coating

IS 1929 : 1982 Specification for Hot Forged Steel Rivets for Hot Closing (12 to 36 mm Diameter)

IS 1956 : Part 1 : 1976 Glossary of terms relating to iron and steel Part I General metallurgy, heat treatment and testing

IS 1956 : Part 2 : 1976 Glossary of Terms Relating to Iron and Steel - Part II : Steel Making

IS 1956 : Part III : 1975 Glossary of Terms Relating to Iron and Steel - Part III : Hot-Rolled Steel Products (Excluding Sheet and Strip)

IS 1956 : Part III : 1975 Glossary of Terms Relating to Iron and Steel - Part III : Hot-Rolled Steel Products (Excluding Sheet and Strip)

IS 1956 : Part IV : 1975 Glossary of Terms Relating to Iron and Steel - Part IV : Steel Sheet and Strip

IS 1956 : Part IV : 1975 Glossary of Terms Relating to Iron and Steel - Part IV : Steel Sheet and Strip

IS 1956 : Part 5 : 1976 Glossary of Terms Relating to Iron and Steel : Part 5 Bright steel bar and steel wire

IS 1956 : Part 5 : 1976 Glossary of Terms Relating to Iron and Steel : Part 5 Bright steel bar and steel wire

IS 1956 : Part 6 : 1976 Glossary of Terms Relating to Iron and Steel : Part 6 Forging (including drop forging)

IS 1956 : Part 6 : 1976 Glossary of Terms Relating to Iron and Steel : Part 6 Forging (including drop forging)

IS 1956 : Part VII : 1976 Glossary of Terms Relating to Iron and Steel - Part VII : Wrought Iron

IS 1956 : Part VII : 1976 Glossary of Terms Relating to Iron and Steel - Part VII : Wrought Iron

IS 1956 : Part VIII : 1976 Glossary of Terms Relating to Iron and Steel - Part VIII : Steel Tubes and Pipes

IS 1977 : 1996 Low Tensile Structural Steels - Specification

IS 1985 : Part 1 : 1980 Recommended practice for preparation of iron and steel for electroplating Part 1 high carbon steel

IS 1985 : Part II : 1980 Recommended Practice for Preparation of Iron and Steel for Electroplating - Part II : Low Carbon Steel

IS 1985 : Part 3 : 1980 Recommended practice for preparation of iron and steel for electroplating Part 3 Iron castings

IS 1986 : 1981 Code of practice for hard chromium plating on iron and steel for general engineering purposes

IS 1990 : 1973 Steel rivet and stay bars for boilers

IS 1990 : 1973 Steel rivet and stay bars for boilers

IS 2002 : 1992 Steel plates for pressure vessels for intermediate & high temperature service including boilers

IS 2002 : 1992 Steel plates for pressure vessels for intermediate & high temperature service including boilers

IS 2004 : 1991 Carbon steel forgings for general engineering purposes

IS 2039 : Parts 1 to 3 : 1991 Steel Tubes for Bicycle and Cycle Rickshaws - Specification

IS 2039 : Parts 1 to 3 : 1991 Steel Tubes for Bicycle and Cycle Rickshaws - Specification

IS 2041 : 1995 Steel Plates for Pressure Vessels Used at Moderate and Low Temperature - Specification

IS 2041 : 1995 Steel Plates for Pressure Vessels Used at Moderate and Low Temperature - Specification

IS 2049 : 1978 Colour code for the identification of wrought steels for general engineering purposes

IS 2049 : 1978 Colour code for the identification of wrought steels for general engineering purposes

IS 2062 : 1999 Steel for General Structural Purposes - Specification

IS 2062 : 2006 Hot Rolled Low, Medium and High Tensile Structural Steel

IS 2090 : 1983 Specification for high tensile steel bars used in prestressed concrete

IS 2090 : 1983 Specification for high tensile steel bars used in prestressed concrete

IS 2100 : 1970 Steel billets, bars and sections for boilers

IS 2140 : 1978 Specification for Stranded Galvanized Steel Wire for Fencing

IS 2155 : 1982 Specification for Cold Forged Solid Steel Rivets for Hot Closing (6 to 16 mm Diameter)

IS 2155 : 1982 Specification for Cold Forged Solid Steel Rivets for Hot Closing (6 to 16 mm Diameter)

IS 2220 : 1990 Engineering metrology - Steel straightedges - Specification

IS 2255 : 1977 Specification for Mild Steel Wire Rod for the Manufacture of Machine Screws (By Cold Heading Process)

IS 2255 : 1977 Specification for Mild Steel Wire Rod for the Manufacture of Machine Screws (By Cold Heading Process)

IS 2265 : 1978 Specification for Galvanized Steel Wire Strand for Signaling Purposes

IS 2266 : 1989 Steel Wire Ropes for General Engineering Purposes - specification

IS 2266 : 2002 Steel Wire Ropes for General Engineering Purposes - Specification

IS 2314 : 1986 Specification for Steel Sheet Piling Sections

IS 2336 : 1963 Specification for Stainless Steel Milk Vats

IS 2365 : 1977 Specification for Steel Wire Suspension Ropes for Lifts, Elevators and Hoists

IS 2385 : 1977 Specification for Hot-Rolled Mild Steel Sheet and Strip in Coil Form for Cold-Reduced Tinplate and Cold-Reduced Blackplate

IS 2385 : 1977 Specification for Hot-Rolled Mild Steel Sheet and Strip in Coil Form for Cold-Reduced Tinplate and Cold-Reduced Blackplate

IS 2429 : Part 1 : 1987 Specification for Round Steel Short Link Chains (Electric Butt Welded), Grade L(3) Part 1 Non-Calibrated Load Chain for Lifting Purposes

IS 2431 : 1963 Specification for Steel Wheelbarrows (Single-wheel Type)

IS 2487 : 1972 Specification for Flat Steel Healds (Excluding Jacquard Leno Weaving Healds)

IS 2487 : 1972 Specification for Flat Steel Healds (Excluding Jacquard Leno Weaving Healds)

IS 2492 : 1976 Specification for Stainless Steel Road Milk Tankers

IS 2507 : 1975 Cold-rolled steel strips for springs

IS 2507 : 1975 Cold-rolled steel strips for springs

IS 2546 : 1974 Specification for galvanized mild steel fire bucket

IS 2546 : 1974 Specification for galvanized mild steel fire bucket

IS 2552 : 1989 Steel drums (galvanized and ungalvanized)

IS 2581 : 2002 Round Strand Galvanized Steel Wire Ropes for Shipping Purposes - Specification

IS 2581 : 1989 Round Strand Galvanized Steel Wire Ropes for Shipping Purposes - Specification

IS 2589 : 1975 Hard drawn steel wire for upholstery springs

IS 2589 : 1975 Hard drawn steel wire for upholstery springs

IS 2591 : 1982 Dimensions for Hot Rolled Steel Bars for Threaded components

IS 2611 : 1964 Carbon chromium molybdenum steel forgings for high temperature services

IS 2629 : 1985 Recommended Practice for Hot-Dip Galvanizing of Iron and Steel

IS 2629 : 1985 Recommended Practice for Hot-Dip Galvanizing of Iron and Steel

IS 2637 : 2004 /ISO 487 : 1998 Steel Roller Chains, Types S and C, Attachments and Sprockets

IS 2637 : 1991/ISO 487 : 1984 Steel roller chains Type S and C, Attachments and chain wheels

IS 2644 : 1994 High tensile steel castings

IS 2667 : 1988 Fittings for rigid steel conduits for electrical wiring

IS 2688 : 1964 Specification for Insulated Stainless Steel Milk Storage Tank

IS 2688 : 1964 Specification for Insulated Stainless Steel Milk Storage Tank

IS 2689 : 1964 Specification for Batch Pasteurizer (Stainless Steel)

IS 2707 : 1996 Carbon Steel Castings for Surface Hardening - Specification

IS 2708 : 1993 1.5 Percent manganese steel castings for general engineerig purposes

IS 2713 : Parts I to III : 1980 Specification for Tubular Steel Poles for Overhead Power Lines

IS 2721 : 2003 Galvanized Steel Chain Link Fence Fabric - Specification

IS 2721 : 1979 Specification for Galvanized Steel Chain Link Fence Fabric

IS 2750 : 1964 Specification for Steel Scaffoldings

IS 2750 : 1964 Specification for Steel Scaffoldings

IS 2751 : 1979 Code of Practice for Welding of Mild Steel Plain and Deformed Bars for Reinforced Concrete Construction

IS 2758 : 1969 Mild steel point hooks for use with wire rope thimbles

IS 2759 : 1969 Higher tensile steel point hooks for use with wire rope thimbles

IS 2760 : 1980 Specification for Steel Chain Slings

IS 2760 : 1980 Specification for Steel Chain Slings

IS 2811 : 1987 Recommendations for Manual Tungsten Inert-gas Arc Welding of Austenitic Stainless Steel

IS 2829 : 1979 Specification for Steam-jacketed Ghee Pans (Stainless Steel)

IS 2830 : 1992 Carbon steel cast billet ingots,billets,blooms and slabs for re-rolling into steel for general structural purposes (Superseding IS 6914)

IS 2830 : 1992 Carbon steel cast billet ingots,billets,blooms and slabs for re-rolling into steel for general structural purposes (Superseding IS 6914)

IS 2831 : 2001 Carbon Steel Cast Billet Ignots, Billets, Blooms and Slabs For Re-rolling into Low Tensile Structural Steel - Specification

IS 2831 : 2001 Carbon Steel Cast Billet Ignots, Billets, Blooms and Slabs For Re-rolling into Low Tensile Structural Steel - Specification

IS 2856 : 1999 Carbon Steel Castings for Pressure Containing Parts Suitable for Fusion Welding - Specification

IS 2879 : 1998 Mild steel for metal arc welding electrodes

IS 2898 : 1976 Specification for Steel Balls for Rolling Bearings

IS 2985 : 1990 Steel Castings for Ship's Structure - Specification

IS 2986 : 1990 Steel castings for marine engines and boilers

IS 2986 : 1990 Steel castings for marine engines and boilers

IS 2998 : 1982 Specification for Cold Forged Steel Rivets for Cold Closing (1 to 16 mm Diameter)

IS 2998 : 1982 Specification for Cold Forged Steel Rivets for Cold Closing (1 to 16 mm Diameter)

IS 3019 : 1973 Specification for High Speed Steel Butt-Welded Single Point Turning Tools

IS 3019 : 1973 Specification for High Speed Steel Butt-Welded Single Point Turning Tools

IS 3024 : 2006 Grain Oriented Electrical Steel Sheet and Strip

IS 3024 : 1997 Grain orinted electrical steel sheets and strips

IS 3038 : 2006 Martensitic Stainless Steel and Alloy Steel Castings for Pressure Containing Parts Suitable for High Temperature Service - Specification

IS 3038 : 1992 Martensitic Stainless Steel and Alloy Steel Castings for Pressure Containing Parts Suitable for High Temperature Service - Specification

IS 3039 : 1988 Structural steel for construction of hulls of ships

IS 3074 : 2005 Steel Tubes for Automotive Purposes - Specification

IS 3074 : 2005 Steel Tubes for Automotive Purposes - Specification

IS 3177 : 1999 Code of Practice for Electric Overhead Travelling Cranes and Gantry Cranes other than Steel Work Cranes

IS 3177 : 1999 Code of Practice for Electric Overhead Travelling Cranes and Gantry Cranes other than Steel Work Cranes

IS 3195 : 1992 Steel for the manufacture of volute and helical springs (for railway rolling stock)

IS 3195 : 1992 Steel for the manufacture of volute and helical springs (for railway rolling stock)

IS 3196 : Part 1 : 1992 Welded Low Carbon Steel Cylinders Exceeding 5 Litre Water Capacity for Low Pressure Liquefiable Gases - Part 1 : Cylinders for liquefied Petroleum Gases (LPG) - Specification

IS 3196 : Part 1 : 2006 Welded Low Carbon Steel Cylinders Exceeding 5 Litre Water Capacity for Low Pressure Liquefiable Gases - Part 1 : Cylinders for Liquefied Petroleum Gases (LPG) - Specification

IS 3196 : Part 2 : 1992 Welded Low Carbon Steel Cylinders Exceeding 5 Litre Water Capacity for Low Pressure Liquefiable Gases - Part 2 : Cylinders for Liquefiable Gases Other Than LPG - Specification

IS 3196 : Part 2 : 2006 Welded Low Carbon Steel Cylinders Exceeding 5 Litre Water Capacity for Low Pressure

Liquefiable Gases - Part 2 : Cylinders for Liquefiable Non-Toxic Gases Other than LPG - Specification

IS 3196 : Part 3 : 1991 Welded low carbon steel gas cylinder exceeding 5 litre water capacity for low pressure liquefiable gases Part 3 Methods of test

IS 3196 : Part 3 : 1991 Welded low carbon steel gas cylinder exceeding 5 litre water capacity for low pressure liquefiable gases Part 3 Methods of test

IS 3196 : Part 4 : 2001 Welded Low Carbon Steel Cylinders Exceeding 5 Litre Water Capacity for Low Pressure Liquefiable Gases - Specification - Part 4 : Cylinders for Toxic and Corrosive Gases

IS 3196 : Part 4 : 2001 Welded Low Carbon Steel Cylinders Exceeding 5 Litre Water Capacity for Low Pressure Liquefiable Gases - Specification - Part 4 : Cylinders for Toxic and Corrosive Gases

IS 3257 : 1980 Stainless steel compartmental trays

IS 3258 : 1980 Stainless steel serving utensils

IS 3261 : 1980 Carbon steel forgings for shipbuilding industry

IS 3271 : 1966 General requirements for steel cowl ventilators with detachable components

IS 3272 : 1966 Dimensions for oval-head steel cowl ventilators

IS 3273 : 1966 Dimensions for circular-head steel cowl ventilators

IS 3275 : 1966 Dimensions for steel cowl ventilators accessories

IS 3276 : 1966 Dimensions for steel cowl ventilators - mechanical turning arrangements

IS 3278 : 1966 Dimensions for detachable coaming covers and wire mesh grids for steel cowl ventilators

IS 3298 : 1981 Mild steel rivet bars for shipbuilding

IS 3312 : 1984 Specification for steel shelving cabinets (adjustable type)

IS 3313 : 1983 Specification for Steel Filing Cabinets for General Office Purposes

IS 3314 : 1984 Specification for steel clothes lockers

IS 3368 : 1984 Specification for Wooden Heald Frames for Wire and Flat Steel Healds

IS 3374 : 1983 Specification for Preformed Steel Wire Ropes for Aircraft Controls

IS 3382 : 1965 Specification for Stainless Steel Milk Pipes and Fittings

IS 3407 : Part 1 : 1983 Method for Creep Testing of Steel at Elevated Temperatures - Part 1 : Tensile Creep Testing

IS 3407 : Part 2 : 1983 Method for Creep Testing of Steel at Elevated Temperatures - Part 2 : Tensile Creep Stress Rupture Testing

IS 3411 : 1985 Stainless steel cooking utensils

IS 3422 : 1966 Code of practice for packaging of steel and steel products for export purposes

IS 3424 : 1985 Stainless steel table utensils

IS 3431 : 1982 Steel for the manufacture of volute, helical and laminated springs for automotive suspension

IS 3444 : 1999 Corrosion Resistant High Alloy Steel And Nickel Base Castings for General Applications - Specification

IS 3445 : 1992 Forged steel rolls

IS 3469 : Parts I to III : 1974 - Tolerances for Closed Die Steel Forgings

IS 3479 : 1966 General requirements for steel drop, upset and press forgings

IS 3480 : 1966 Flexible steel conduits for electrical wiring

IS 3489 : 1985 Specification for enamelled steel bath tubs

IS 3497 : 1992 Specification for steel wardrobes (adjustable type)

IS 3502 : 1994 Steel Chequered Plates - Specification

IS 3503 : 1966 Steel for marine boilers, pressure vessels and welded machinery structures

IS 3525 : 1998 Metal arc welding for hull constructions of merchant ships in carbon and carbon -manganese steels

IS 3589 : 2001 Steel Pipes for Water and Sewage (168.3 to 2 540 mm Outside Diameter) - Specification

IS 3589 : 2001 Steel Pipes for Water and Sewage (168.3 to 2 540 mm Outside Diameter) - Specification

IS 3600 : Part 1 : 1985 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 1 Cruciform fillet weld tensile test

IS 3600 : Part 2 : 1985 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 2 Beam impact (charpy V-

notch) test

IS 3600 : Part 3 : 1984 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 3 Transverse tensile test on butt welds

IS 3600 : Part 3 : 1984 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 3 Transverse tensile test on butt welds

IS 3600 : Part 4 : 1984 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 4 Longitudinal tensile test on cylindrical weld metal test pieces on butt welds

IS 3600 : Part 5 : 1983/ISO 5173 : 1981 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 5 Transverse root and face bend test on butt welds

IS 3600 : Part 6 : 1983/ISO 5177 : 1981 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 6 Transverse side bend test on butt welds

IS 3600 : Part 7 : 1985 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 7 Longitudinal root and face bend test on butt welds

IS 3600 : Part 8 : 1985 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 8 Nick break test and fillet weld fracture test

IS 3600 : Part 9 : 1985 Method of Testing Fusion Welded Joints and Weld Metal in Steel: Part 9 Macro and micro examination

IS 3601 : 1984 Steel tubes for mechanical and general engineering purposes

IS 3601 : 2006 Steel Tubes for Mechanical and General Engineering Purposes - Specification

IS 3609 : 1966 Chrome molybdenum steel, seamless, boiler and superheater tubes

IS 3609 : 1966 Chrome molybdenum steel, seamless, boiler and superheater tubes

IS 3618 : 1966 Specification for Phosphate Treatment of Iron and Steel for Protection Against Corrosion

IS 3711 : 1990 Wrought steel - Selection and preparation of samples and test pieces for mechanical tests

IS 3739 : 1987 Dimensional tolerances for carbon and alloy constructional steel products

IS 3748 : 1990 Tool and Die Steels - Specification (Superseding IS 3749)

IS 3748 : 1990 Tool and Die Steels - Specification (Superseding IS 3749)

IS 3803 : Part 1 : 1989/ISO 2566-1 : 1984 Steel - Conversion of Elongation Values: Part I Carbon & loow alloy steels

IS 3803 : Part 2 : 1989/ISO 2566-2 : 1984 Steel - Conversion of Elongation Values: Part 2 Austenitic steels

IS 3821 : 1973 Methods for determination of weight of coating on hot-dip aluminized iron and steel articles

IS 3835 : 1966 Specification for Aluminized Steel Core Wire for Aluminium Conductors (ACSR)

IS 3837 : 1976 Accessories for rigid steel conduits for electrical wiring

IS 3837 : 1976 Accessories for rigid steel conduits for electrical wiring

IS 3843 : 1995 Specification for steel back flap hinges

IS 3848 : 1981 Method for end quench test for hardenability of steel

IS 3885 : Part 1 : 1992 Steel for the manufacture of laminated springs (railway rolling stock) Part 1 Flat Sections

IS 3885 : Part 1 : 1992 Steel for the manufacture of laminated springs (railway rolling stock) Part 1 Flat Sections

IS 3885 : Part 2 : 1992 Steel for the Manufacture of Laminated Springs (Railway Rolling Stock) - Part 2 : Rib and Groove Sections

IS 3885 : Part 2 : 1992 Steel for the Manufacture of Laminated Springs (Railway Rolling Stock) - Part 2 : Rib and Groove Sections

IS 3888 : 1987 Specification for Spatula, Stainless Steel, Dental

IS 3930 : 1994 Flame and induction hardening steels

IS 3945 : 1966 Steel for naval purposes

IS 3948 : 1986 Specification for Calibrated High Tensile Steel (Round Link) Chain (Electric Butt Welded) for Chain Conveyors and Coal Ploughs Used in Mines

IS 3948 : 1986 Specification for Calibrated High Tensile Steel (Round Link) Chain (Electric Butt Welded) for Chain Conveyors and Coal Ploughs Used in Mines

IS 3954 : 1991 Hot Rolled Steel Channel Sections for General Engineering Purposes - Dimensions

IS 3972 : Part 1 : Sec 1 : 1982 Methods of test for vitreous enamelware - Part 1 : Production of specimens for testing -

Section 1 : Enamelled sheet steel

IS 3972 : Part 1 : Sec 1 : 1982 Methods of test for vitreous enamelware - Part 1 : Production of specimens for testing - Section 1 : Enamelled sheet steel

IS 3975 : 1999 Mild steel wires, formed wires and tapes for armouring of cables

IS 4000 : 1992 Code of practice for high strength bolts in steel structures

IS 4014 : Part 1 : 1967 Code of practice for steel tubular scaffolding Part 1 Definitions and materials

IS 4014 : Part II : 1967 Code of Practice for Steel Tubular Scaffolding - Part II : Safety Regulations for Scaffolding

IS/ISO 4033 : 1979 Industrial Fasteners - Threaded Steel Fasteners - Hexagon Nuts of Style 2 - Product Grade A and B - Specification

IS 4072 : 1975 Specification for Steel for Spring Washers

IS 4072 : 1975 Specification for Steel for Spring Washers

IS 4075 : 1985 Method for macrostreak flaw test for steel

IS 4137 : 1985 Code of practice for heavy duty electric overhead travelling cranes including special service machines for use in steel work

IS 4163 : 2004 /ISO 1998 Steel - Determination of Content of Nonmetalic Inclusions - Micorgraphic Methods Using Standard Diagrams

IS 4163 : 1982 Method for determination of inclusion content in steel by macroscopic method

IS 4180 : 1967 Code of practice for corrosion protection of light gauge steel sections used in building

IS 4184 : 1967 Steel wheel barrows (with two wheels)

IS 4184 : 1967 Steel wheel barrows (with two wheels)

IS 4223 : 1975 Specification for Steel Wire for Umbrella Ribs

IS 4224 : 1972 Specification for Steel Wire for Staples, Pins and Clips

IS 4224 : 1972 Specification for Steel Wire for Staples, Pins and Clips

IS 4225 : 2004 Recommended Practice for Straight Beam Ultrasonic Testing of Steel Plates

IS 4225 : 1979 Recommended practice for straight beam ultrasonic testing of steel plates

IS 4260 : 2004 Recommended Practice for Ultrasonic Testing of Butt welds in Ferritic Steel

IS 4260 : 1986 Recommended practice for ultrasonic testing of butt welds in ferritic steel

IS 4270 : 2001 Steel Tubes Used for Water Wells - Specification

IS 4310 : 1967 Weldable steel pipe fittings for marine purposes

IS 4351 : 1976 Specification for steel door frames

IS 4351 : 2003 Steel Door Frames - Specification

IS 4353 : 1995 Submerged Arc Welding of Mild Steel and Low Alloy Steels - Recommendations

IS 4367 : 1991 Alloy steel forgings for general industrial use

IS 4367 : 1991 Alloy steel forgings for general industrial use

IS 4368 : 1967 Alloy steel billets, blooms and slabs for forging for general engineering purposes

IS 4374 : 1980 Specification for Mild Steel Fabricated Vertical Bollards with and Without Lugs

IS 4384 : 1967 Specification for Steel Watertight Doors

IS 4384 : 1967 Specification for Steel Watertight Doors

IS 4397 : 1999 Cold-rolled Carbon Steel Strips for Ball and Roller Bearing Cages/Retainers - Specification

IS 4398 : 1994 Carbon-chromium Steel for the Manufacture of Balls, Rollers and Bearing Races - Specification

IS 4398 : 1994 Carbon-chromium Steel for the Manufacture of Balls, Rollers and Bearing Races - Specification

IS 4430 : 1979 Specification for Mould Steels

IS 4430 : 1979 Specification for Mould Steels

IS 4431 : 1978 Carbon and carbon manganese free cutting steels

IS 4431 : 1978 Carbon and carbon manganese free cutting steels

IS 4432 : 1988 Case hardening steels

IS 4432 : 1988 Case hardening steels

IS 4438 : 1967 Specification for Perforated Steel Strips (Fillets) for Take-up Rollers

IS 4454 : Part 1 : 2001 Steel Wire for Mechanical Springs - Specification - Part 1 : Cold Drawn Unalloyed Steel Wire

IS 4454 : Part 2 : 2001 Steel Wire for Mechanical Springs - Specification - Part 2 : Oil Hardened and Tempered Steel Wire

IS 4454 : Part 3 : 1975 Part 3 Oil hardened and tempered steel wiresalloyed

IS 4454 : Part 4 : 2001 Steel Wire for Mechanical Springs - Specification - Part 4 : Stainless Steel Wire

IS 4454 : Part 4 : 2001 Steel Wire for Mechanical Springs - Specification - Part 4 : Stainless Steel Wire

IS 4465 : 1984 Specification for Metal Heald Frames for Flat Steel Healds

IS 4475 : Part 1 : 1986 Specification for Crane-suspended Ladles for Foundries - Part 1 : Straight/Taper Sided Geared Ladles 0.25 to 10 Tonnes for Iron and Steel Foundries

IS 4475 : Part 4 : 1988 Specification for Crane-Suspended Ladles for Foundries: Part 4 Taper sided non geared ladles 15 to 50 tonnes capacities for iron and steel foundries

IS 4491 : 1994 Steel castings for high magnetic permeability

IS 4516 : 1968 Elliptical mild steel tubes

IS 4516 : 1968 Elliptical mild steel tubes

IS 4522 : 1986 Heat resistant alloy steel and nickel base castings

IS 4522 : 1986 Heat resistant alloy steel and nickel base castings

IS 4536 : Part 1 : 1987 Specification for Composite Bottom Stainless Steel Cooking Utensils - Part 1 : Copper Electrodeposited

IS 4536 : Part II : 1969 Specification for Composite Bottom Stainless Steel Cooking Utensils - Part II : 3-ply Construction

IS 4536 : Part II : 1969 Specification for Composite Bottom Stainless Steel Cooking Utensils - Part II : 3-ply Construction

IS 4536 : Part 3 : 1987 Specification for Composite Bottom Stainless Steel Cooking Utensils - Part 3 : Copper Clad

IS 4606 : 1983 Steel shots for use in foundries

IS 4606 : 1983 Steel shots for use in foundries

IS 4647 : 1998 Inland Vessels - Detachable Steel Ladder - Specification

IS 4649 : 1968 Adaptors for flexible steel conduits

IS 4693 : 1968 Specification for Steel Accessories for Marine Piping Systems

IS 4711 : 1974 Methods for sampling of steel pipes, tubes and fittings

IS 4711 : 1974 Methods for sampling of steel pipes, tubes and fittings

IS 4712 : 1984 Forged steel,socket-welding fittings

IS 4712 : 1984 Forged steel,socket-welding fittings

IS 4736 : 1986 Specification for Hot-dip Zinc Coatings on Mild Steel Tubes

IS 4736 : 1986 Specification for Hot-dip Zinc Coatings on Mild Steel Tubes

IS 4740 : 1979 Code of Practice for Packaging of Steel Tubes

IS 4743 : 1968 Specification for Settling Tanks for Ghee (Stainless Steel)

IS 4759 : 1996 Hot-dip zinc coatings on structural steel and other allied products

IS 4759 : 1996 Hot-dip zinc coatings on structural steel and other allied products

IS 4768 : 1981 Specification for Stainless Steel Buckets

IS 4777 : 1968 Performance tests for protection schemes used in protection of light gauge steel against corrosion

IS 4826 : 1979 - Specification for Hot-Dipped Galvanized Coatings on Round Steel Wires

IS 4826 : 1979 - Specification for Hot-Dipped Galvanized Coatings on Round Steel Wires

IS 4853 : 1982 Recommended practice for radiographic inspection of fusion welded butt joints in steel pipes

IS 4880 : Part 7 : 1975 Code of practice for design of tunnels conveying water: Part 7 Structural design of steel lining

IS 4882 : 1979 Specification for Low Carbon Steel Wire for Rivets for Use in Bearing Industry

IS 4882 : 1979 Specification for Low Carbon Steel Wire for Rivets for Use in Bearing Industry

IS 4896 : 1992 One percent chromium steel castings for resistance to abrasion

IS 4897 : 1994 Deviations on untoleranced dimensions and mass of steel castings

IS 4898 : 1989 Steel Castings for Case Carburizing - Specification

IS 4898 : 1989 Steel Castings for Case Carburizing - Specification

IS 4899 : 2006 Ferritic and Martensitic Steel Castings for Use at Low Temperature - Specification

IS 4899 : 1991 Ferritic and martensitic steel casting for use at low temperature

IS 4922 : 1968 Seamless steel tubes (suitable for welding) for aircraft purposes

IS 4922 : 1968 Seamless steel tubes (suitable for welding) for aircraft purposes

IS 4923 : 1997 Hollow steel sections for structural use

IS 4938 : 1968 Specification for Insulated Stainless Steel Milk Storage Tanks, Vertical Type

IS 4943 : 1968 Assessment of butt and fillet fusion welds in steel sheet, plate and pipe

IS 4948 : 2002 Welded Steel Wire Fabric for General use - Specification

IS 4948 : 1974 Specification for welded steel wire fabric for general use

IS 5074 : 1969 Method for axial load fatigue testing of steel

IS 5133 : Part 1 : 1969 Boxes for enclosure of the electrical accessories:Part 1 Steel and cast iron boxes

IS 5206 : 1983 Covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels

IS 5239 : 1969 Wire rod for the manufacture of aluminized steel core wire for aluminium conductors

IS 5319 : 1987 Specification for Commercial Steel Wool

IS 5319 : 1987 Specification for Commercial Steel Wool

IS 5347 : Part 2 : 1993/ISO 5832-1 : 1987 Requirements for orthopaedic Implants Part 2 Wrought stainless steel

IS 5347 : Part 13 : 1997/ISO 5832-9 : 1992 Requirements for orthopaedic implants Part 13 Wrought high nitrogen stainless steel

IS 5429 : 1979 Dimensions for steel tubes for automotive purposes

IS 5433 : 1969 Oil well steel casing pipes and couplings

IS 5433 : 1969 Oil well steel casing pipes and couplings

IS 5443 : 1994 High speed steel reamers - Technical supply conditions

IS 5443 : 1994 High speed steel reamers - Technical supply conditions

IS 5488 : 1987 Dimensions and dimensional tolerances for hot rolled steel plates for ship's hull structure

IS 5489 : 1975 Carburizing steels for use in bearing industry

IS 5489 : 1975 Carburizing steels for use in bearing industry

IS 5517 : 1993 Steels for Hardening and Tempering - Specification

IS 5517 : 1993 Steels for Hardening and Tempering - Specification

IS 5518 : 1996 Steels for die blocks for drop forging

IS 5521 : 1980 Specification for Steel Tanks for Storage of Molasses

IS 5522 : 1992 Stainless steel sheets and strips for utensils

IS 5530 : 1987 Recommendations for production rectification and repair of steel castings by metal arc welding process

IS 5530 : 2005 Recommendations for Production, Rectification and Repair of Steel Castings by Metal Arc Welding Process

IS 5606 : 1970 Specification for Steel Bins for Grain Storage

IS 5629 : 1970 Specification for Mild Steel Forged Triangular Lifting Eyes

IS 5651 : 1987 Specification for Steels for Pneumatic Tools

IS 5822 : 1994 Code of Practice for Laying of Electrically Welded Steel Pipes for Water Supply

IS 5845 : 1993 Code of practice for inspection of low pressure welded steel gas cylinders other than LPG cylinders in use

IS 5852 : 2004 Protective Steel Toe Caps for Footwear - Specification

IS 5852 : 1996 Protective steel toe caps for footwear - Specification

IS 5856 : 1991 Corrosion and heat resisting chromium-nickel steel solid welding rods, bare electrodes

IS 5872 : 1990 Cold Rolled Steel Strips (Box Strappings) - Specification

IS 5873 : 1970 Steel cut-wire shots for use in foundries

IS 5878 : Part 6 : 1975 Code of practice for construction of tunnel conveying water: Part 6 Steel lining

IS 5878 : Part 6 : 1975 Code of practice for construction of tunnel conveying water: Part 6 Steel lining

IS 5895 : 1985 Specification for Steel Roller Conveyors

IS 5904 : 1978 Steel chaplets for use in ferrous foundries

IS 5905 : 1989 Sprayed aluminium and zinc coatings on iron and steel

IS 5929 : 1970 Inspection and testing procedure for circular steel tubes for aircraft purposes

IS 5963 : 1971 Specification for Knee Joint without Lock for Steel Orthopaedic Calipers

IS 5986 : 1992 Hot rolled steel plates,sheets,strips and flats for flanging and forming oper ation-Specification

IS 5986 : 2002 Hot Rolled Steel Flat Prodcuts for Structural Forming and Flanging Purposes - Specification

IS 5993 : 1970 Aluminized steel wire for telegraph and telephone purposes

IS 6005 : 1998 Code of practice for phosphating of iron and steel

IS 6011 : 1970 Carbon steel tubes for use on board ships for pressure services

IS 6011 : 1970 Carbon steel tubes for use on board ships for pressure services

IS 6079 : 1989 Low alloy cast steel grinding media

IS 6079 : 1989 Low alloy cast steel grinding media

IS 6158 : 1984 Recommended Practice for Safeguarding Against Embrittlement of Hot-dip Galvanized Iron and Steel Products

IS 6158 : 1984 Recommended Practice for Safeguarding Against Embrittlement of Hot-dip Galvanized Iron and Steel Products

IS 6159 : 1998 Recommended Practice for Design and Fabrication of Iron and Steel Products Prior to Galvanizing and Metal Spraying

IS 6176 : 1971 Specification for Steel Ladders for Ship's Use

IS 6221 : 1971 Specification for Pelvic Band for Steel Orthopedic Calipers and Braces

IS 6221 : 1971 Specification for Pelvic Band for Steel Orthopedic Calipers and Braces

IS 6240 : 1999 Hot Rolled Steel Plate (up to 6 mm) Sheet and Strip for the Manufacture of Low Pressure Liquefiable Gas Cylinders - Specification

IS 6240 : 1999 Hot Rolled Steel Plate (up to 6 mm) Sheet and Strip for the Manufacture of Low Pressure Liquefiable Gas Cylinders - Specification

IS 6286 : 1971 Seamless and welded steel pipes for sub-zero temperature service

IS 6286 : 1971 Seamless and welded steel pipes for sub-zero temperature service

IS 6392 : 1971 Steel pipe flanges

IS 6396 : 2000 Methods of Measuring Decarburized Depth of Steel

IS 6416 : 1988 Methods for Measuring Case Depth of Steel

IS 6419 : 1996 Welding rods and bare electrodes for gas shielded arc welding of structural steel

IS 6441 : Part IV : 1972 Methods of Test for Autoclaved Cellular Concrete Products - Part IV : Corrosion Protection of Steel Reinforcement in Autoclave Cellular Concrete

IS 6527 : 1995 Stainless steel wire rod

IS 6527 : 1995 Stainless steel wire rod

IS 6528 : 1995 Stainless steel wire

IS 6529 : 1996 Stainless steel blooms, billets and slabs for forging

IS 6529 : 1996 Stainless steel blooms, billets and slabs for forging

IS 6533 : Part 1 : 1989 Code of practice for design and construction of steel chimneys Part 1 Mechanical aspects )

IS 6533 : Part 1 : 1989 Code of practice for design and construction of steel chimneys Part 1 Mechanical aspects )

IS 6533 : Part 2 : 1989 Code of practice for design and construction of steel chimneys Part 2 Structural aspects

IS 6533 : Part 2 : 1989 Code of practice for design and construction of steel chimneys Part 2 Structural aspects

IS 6560 : 1996 Molybdenum and chromium-molybdenum low alloy steel welding rods and bare electrodes for gas shielded arc welding

IS 6586 : 1989 Recommended practice for metal spraying for protection of iron steel

IS 6594 : 2001 Technical Supply Conditions for Steel Wire Ropes and Strands

IS 6594 : 1977 Technical supply conditions for steel wire ropes and strands

IS 6601 : 1987 Permissible deviations in chemical composition for products analysis of steel

IS 6603 : 2001 Stainless Steel Bars and Flats - Specification

IS 6610 : 1972 Specification for Heavy Washers for Steel Structures

IS 6630 : 1985 Seamless ferritic alloy steel pipes for high temperature steam service

IS 6631 : 1972 Specification for Steel Pipes for Hydraulic Purposes

IS 6639 : 1972 Specification for Hexagon Bolts for Steel Structures

IS 6639 : 2005 Hexagon Head Bolts for General Steel Structures - Specification

IS 6689 : 2003/ISO 8734 : 1997 Parallel Pines of Hardened Steel and Martensitic Stainless Steel (Dowel Pins)

IS 6728 : 1972 Recuperator tubes, tiles and collars for soaking pits in steel plants

IS 6745 : 1972 Method for determination of mass of zinc coating on zinc coated iron and steel articles

IS 6745 : 1972 Method for determination of mass of zinc coating on zinc coated iron and steel articles

IS 6902 : 1973 Steel wire for spokes

IS 6907 : 1992 Method of sampling steel castings

IS 6911 : 1992 Stainless steel plate, sheet and strip

IS 6913 : 1973 Stainless steel tubes for the food and beverage industry

IS 6915 : 1978 Cast billet ingots and continuously cast billets for rolling into structural steel : oartdinary quality

IS 6916 : 1973 Code of practice for fabrication welding of steel castings

IS 6967 : 1973 Steel for electrically welded round link chains

IS 6987 : 1973 Specification for Steel Precision Polygons

IS 7001 : 1989 Shot peening of steel parts - Specification

IS 7048 : 2006 /ISO 5778 : 1998 Ships and Marine Technology - Small Weathertight Steel Hatches

IS 7138 : 1973 Steel tubes for furniture purposes

IS 7142 : 1995 Welded low carbon steel cylinders for low pressure liquifiable gases not exceeding 5 litre water capacity - Specificatiom

IS 7147 : Part I : 1973 Specification for Steel Bins for Domestic Storage - Part I : Gharelu Kothi

IS 7174 : 1974 Carbon steel tubes for use on board ships for working pressure 0.7 to 1.7 N/mm2

IS 7174 : 1974 Carbon steel tubes for use on board ships for working pressure 0.7 to 1.7 N/mm2

IS 7178 : 2002 Heat-Treated Steel Tapping Screws - Mechanical Properties

IS 7205 : 1974 Safety Code for Erection of Structural Steelwork

IS 7215 : 1974 Tolerances for fabrication of steel structures

IS 7215 : 1974 Tolerances for fabrication of steel structures

IS 7226 : 1974 Cold rolled medium, high carbon and low alloy steel strip for general engineering purposes

IS 7257 : 1973 Specification for Trunks, Steel, Domestic

IS 7257 : 1973 Specification for Trunks, Steel, Domestic

IS 7280 : 1974 Bare wire electrodes for submerged arc welding of structural steels

IS 7285 : 1988 Specification for Seamless Steel Cylinders for Permanent and High Pressure Liquefiable Gases

IS 7285 : Part 1 : 2004 Refillable Seamless Steel Gas Cylinders - Specification - Part 1 : Normalized Steel Cylinders

IS 7285 : Part 2 : 2004 Refillable Seamless Steel Gas Cylinders - Specification - Part 2 : Quenched and Tempered Steel Cylinders with Tensile Strength Less Than 1 100 MPa (112 kgf/mm2)

IS 7291 : 1981 High speed tool steels

IS 7297 : 1974 Olivine sand and flour for use in steel foundries

IS 7307 : Part 1 : 1974 Approval tests for welding procedures Part 1 fusion welding of steel

IS 7310 : Part I : 1974 Approval Tests for Welders Working to Approved Welding Procedures - Part I : Fusion Welding of

Steel

IS 7312 : 1993 Welded and seamless steel dissolved acetylene gas cylinders - Specification

IS 7318 : Part I : 1974 Approval Test for Welders When Welding Procedure Approval is Not Required - Part I : Fusion welding of Steel

IS 7322 : 1985 Specification for specials for steel cylinder reinforced concrete pipes

IS 7371 : 1982 Specification for Steel, Safety Razor Blades

IS 7418 : 1991 Criteria for design of spiral casing (concrete and steel)

IS 7452 : 1990 Specificatiion for hot-rolled steel sections for doors, windows and ventilators

IS 7485 : Part 1 : 2005 /ISO 7046-1 : 1994 Countersunk Flat Head Screws (Common Head Style) With Type H or Type Z Cross Recess - Product Grade A - Part 1 : Steel of Property Class 4.8

IS 7485 : Part 2 : 2005 /ISO 7046-2 : 1990 Countersunk Flat Head Screws (Common Head Style) with Type H or Type Z Cross Recess - Product Grade A - Part 2 : Steel of Property Class 8.8, Stainless Steel and Non-Ferrous Metals

IS 7494 : 1981 Steel for valves for internal combustion engines

IS 7531 : 1990 Surgical Instruments - Corrosion Resistance of Stainless Steel Surgical Instruments - Methods of Tests

IS 7547 : 1987 Steel Nails used as internal chills in steel castings

IS 7557 : 1982 Steel wire : uartto 20 mm for the manufacture of cold forged rivets

IS 7598 : 1990 Classification of steels

IS 7666 : 1988 Ultrasonic Examination of Ferritic Castings of Carbon and Low Alloy Steel - Recommended Procedure

IS 7680 : 1985 Specification for Welded Low Carbon Steel Gas Cylinders for Ammonia (Anhydrous) Gas

IS 7681 : 1985 Specification for Welded Low Carbon Steel Gas Cylinders for Chlorine Gas

IS 7682 : 1985 Specification for Welded Low Carbon Steel Gas Cylinders for Methyl Bromide Gas

IS 7705 : 1975 Code of practice for packaging of precision and special purpose steel tubes

IS 7705 : 1975 Code of practice for packaging of precision and special purpose steel tubes

IS 7739 : Part 5 : 1976 Code of Practice for Preparation of Metallographic Specimens - Part 5 Iron and steel and their examination

IS 7743 : 2006 Recommended Practice for Magnetic Particle Testing and Inspection of Steel Forgings

IS 7743 : 1975 Recommended practice for magnetic particle testing and inspection of steel forgings

IS 7760 : 1985 Specification for steel glass-front cabinets

IS 7761 : 1983 Specification for steel book cases

IS 7806 : 1993 Martensitic and austenitic high alloy steel castings for high temperature service

IS 7887 : 1992 Mild steel wire rods for general engineering purposes

IS 7899 : 1992 Alloy steel castings suitable for pressure services

IS 7899 : 2006 Alloy Steel Castings Suitable for Pressure Services - Specification

IS 7904 : 1995 High carbon steel wire rods

IS 8036 : 1976 Mild steel transformer cooling tubes

IS 8036 : 1976 Mild steel transformer cooling tubes

IS 8051 : 1976 Steel ingots and billets for the production of volute, helical and laminated springs for automotive suspension

IS 8052 : 1990 Steel ingots,billets and blooms for the production of volute and helical and laminated springs railway rolling stock (Superseding IS 8054:1976)

IS 8052 : 2006 Steel Ingots, Billets and Blooms for the Production of Springs, Rivets and Screws for General Engineering Applications - Specification

IS 8053 : 1976 Specification for Steel Ingots and Billets for the Production of Steel Wire for the Manufacture of Wood Screws

IS 8053 : 1976 Specification for Steel Ingots and Billets for the Production of Steel Wire for the Manufacture of Wood Screws

IS 8055 : 1976 Steel ingots and billets for the production of spring washers

IS 8055 : 1976 Steel ingots and billets for the production of spring washers

IS 8056 : 1976 Steel ingots and billets for the production of hard drawn steel wire for upholstry springs

IS 8056 : 1976 Steel ingots and billets for the production of hard drawn steel wire for upholstry springs

IS 8057 : 1976 Steel ingots and billets for the production of wire rod for the manufacture of machine screws : bart cold heading process

IS 8057 : 1976 Steel ingots and billets for the production of wire rod for the manufacture of machine screws : bart cold heading process

IS 8062 : Part 1 : 1976 Code of practice for cathodic protection of steel structures,Part 1 Genral Princples

IS 8062 : Part II : 1976 Code of Practice for Cathodic Protection of Steel Structures - Part II : Underground Pipelines

IS 8062 : Part 3 : 1977 Code of practice for cathodic protection of steel structure,part 3 Ship's hull

IS 8062 : Part 4 : 1979 Code of practice for cathodic protection of steel structures ,part 4 Galvanic protection of dockgates, caissons, piers and jetties

IS 8073 : 1976 Guide for treatment and disposal of steel plant effluents

IS 8092 : 1992 Code for Inspection of Surface Quality of Steel Castings for Valves, Fittings and Other Piping Components (Visual Method)

IS 8119 : 1976 Copper brazed steel tubing

IS 8119 : 1976 Copper brazed steel tubing

IS 8172 : 1976 Specification for Vertical Steel Ladders

IS 8198 : 2004 Steel Cylinders for Compressed Gases (Atmospheric Gases, Hydrogen, High Pressure Liquefiable Gases and Dissolved Acetylene Gases) - Code of Practice

IS 8198 : Part 1 : 1984 Code of practice for steel cylinders for compressed gases Part 1 Atmospheric gases

IS 8198 : Part 2 : 1984 Code of practice for steel cylinders for compressed gases Part 2 Hydrogen gas

IS 8198 : Part 3 : 1984 Code of practice for steel cylinders for compressed gases Part 3 High pressure liquefiable gases

IS 8198 : Part 4 : 1984 Code of practice for steel cylinders for compressed gases:Part 4 Dissolved acetylene gas

IS 8198 : Part 5 : 1984 Code of Practice for Steel Cylinders for Compressed Gases - Part 5 : Liquefied Petroleum Gas (LPG)

IS 8198 : Part 6 : 1988 Code of practice for steel cylinders for compressed gases Part 6 Liquefied chlorine gas

IS 8198 : Part 7 : 1988 Code of practice for steel cylinders for compressed gases Part 7 Ammonia gas

IS 8198 : Part 8 : 1993 Code of practice for steel cylinders for compressed gases Part 8 Common organic refrigerant gases

IS 8198 : Part 9 : 1988 Code of practice for steel cylinders for compressed gases Part 9 Sulphur dioxide gas

IS 8198 : Part X : 1980 Code of Practice for Steel Cylinders for Compressed Gases - Part X : Methyl Bromide Gas

IS 8198 : Part 11 : 1988 Code of practice for steel cylinders for compressed gases Part 11 Methyl chloride gas

IS 8198 : Part 12 : 1982 Code of practice for steel cylinders for compressed gases Part 12 Gases for medical use

IS 8324 : 1988 Code of Practice for Safe use and Maintenance on Non-calibrated Round Steel Link Lifting Chains and Chin Slings

IS 8324 : 1988 Code of Practice for Safe use and Maintenance on Non-calibrated Round Steel Link Lifting Chains and Chin Slings

IS 8363 : 1976 Bare wire electrodes for electroslag welding of steels

IS 8373 : Part 1 : 1991 Specification for steel launches Part 1 Single hull passenger ferry launches

IS 8412 : 1977 Specification for Slotted Countersunk Head Bolts for Steel Structures

IS 8450 : 1977 Ships' steel dog step ladders

IS 8467 : 1977 Specification for steel card-index cabinets

IS 8467 : 1977 Specification for steel card-index cabinets

IS 8500 : 1991 Structural Steel - Microalloyed (Medium and High Strength Qualities) - Specification

IS 8508 : 1988 Code of practice for hot-dip aluminizing of iron and steel

IS 8510 : Part 1 to 3 : 1977 Tinned steel wire for banding of armatures and rotors

IS 8510 : Part 1 to 3 : 1977 Tinned steel wire for banding of armatures and rotors

IS 8563 : 1977 Half round mild steel wire for the manufacture of split pins

IS 8564 : 1977 Steel wire for nipples for spokes

IS 8566 : 1977 Steel wire for reeds

IS 8629 : Parts I to III : 1977 Code of Practice for Protection of Iron and Steel Structures from Atmospheric Corrosion

IS 8629 : Parts I to III : 1977 Code of Practice for Protection of Iron and Steel Structures from Atmospheric Corrosion

IS 8718 : 1978 Specification for vitreous enamelled steel kitchen sinks

IS 8727 : 1978 Specification for vitreous enamelled steel wash bsins

IS 8761 : 1978 Specification for steel folding cots

IS 8780 : 2004 Non-Destructive Testing of Steel Castings - Code of Practice

IS 8780 : 1978 Code of practice for non destructive testing of steel castings

IS 8791 : 1978 Code of practice for ultrasonic flaw detection of ferritic steel forgings

IS 8795 : 1978 Method for determining case depth of carburized steel by fracture test

IS 8800 : 1997 Technical Delivery Conditions for Steel Castings (Excluding Investment Castings)

IS 8811 : 1998 Method for Emission Spectrometric Analysis of Plain Carbon and Low Alloy Steels Point to Plane Technique

IS 8819 : Part 1 : 1978 Hold loading steel dumb barges, Part 1 Capacity and dimensions

IS 8842 : 1978 Specification for High Speed Steel Butt-welded Single Point Planing Tools

IS 8842 : 1978 Specification for High Speed Steel Butt-welded Single Point Planing Tools

IS 8910 : 1978 General technical delivery requirements for steel and steel products

IS 8917 : 1978 Steel plates for galvenizing pots

IS 8939 : 1978 Code of practice for use of oxygen in Iron Steel,and non-ferrous metal foundries

IS 8951 : 2001 Steel Cast Billet Ignots, Billets and Blooms for Production of High Carbon Steel Wire Rods - Specification

IS 8952 : 1995 Steel ingots,blooms and billets for production of mild steel wire rods for generl engineering purposes

IS 8986 : 1994 Percussive drilling - Drilling steels in bar form - Dimensions

IS 8996 : 1988 Specification for 20-litre Steel Jerricans

IS 9006 : 1978 Recommended practice for welding of clad steels

IS 9077 : 1979 Code of practice for corrosion protection of steel reinforcement in RB and RCC construction

IS 9100 : 1979 Methods of sampling steel forgings

IS 9172 : 1979 Recommended design practice for corrosion prevention of steel structures

IS 9175 : Part I : 1979 Rationalized Steels for the Automobile and Ancillary Industry - Part 1 : Chemical Composition

IS 9175 : Part 2 : 1985 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 2 : 15c8 Grade Steel

IS 9175 : Part 3 : 1985 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 3 25C8 Grade Steel




IS 9175 : Part 7 : 1986 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 7 45C8 Grade steel

IS 9175 : Part 8 : 1985 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 8 : 55C8 Grade Steel

IS 9175 : Part 9 : 1985 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 9 11C10S25 Grade steel



IS 9175 : Part 12 : 1988 Specification for Rationalized steels for the automobile and Ancillary Industry - Part 12 : Mechanical and Physical Properties of 35 Mn6Mo3S15



IS 9175 : Part 15 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 15 37C15 Grade steel

IS 9175 : Part 16 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 16 35Mn6Mo3 Grade steel

IS 9175 : Part 17 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 17 35Mn6Mo4 Grade steel

IS 9175 : Part 18 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 18 15Cr3 Grade steel

IS 9175 : Part 19 : 1986 Rationalized Steels for the Automobile and Ancillary Industry - Part 19 : Mechanical and Physical Properties of 16Mn5Cr4 Grade Steel

IS 9175 : Part 20 : 1986 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 20 20MnCr5 Grade steel

IS 9175 : Part 21 : 1987 Specification for Rationalized Steels for the Automobile and Ancillary Industry - Part 21 : Mechanical and Physical Properties of 40Cr4 Grade Steel

IS 9175 : Part 22 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 22 40Cr4Mo3 Grade steel

IS 9175 : Part 23 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 23 25Cr13Mo6 Grade steel

IS 9175 : Part 24 : 1987 Specification for Rationalized Steels for the Automobile and Ancillary Industry - Part 24 : Mechanical and Physical Properties of 35Ni5Cr2 Grade Steel

IS 9175 : Part 25 : 1987 Specification for Rationalized Steels for the Automobile and Ancillary Industry - Part 25 : Mechanical and Physical Properties of 15Ni5Cr4mo1 Grade Steel

IS 9175 : Part 26 : 1986 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 26 16Ni3Cr2 Grade steel

IS 9175 : Part 27 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 27 15Ni7Cr4MO2 Grade steel

IS 9175 : Part 28 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 28 40Ni6Cr4Mo3 Grade steel

IS 9175 : Part 29 : 1987 Rationalized Steels for the Automobile and Ancillary Industry - Part 29 : Mechanical and Physical Properties of 40Ni10Cr3Mo6 Grade Steel

IS 9175 : Part 30 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 30 20Ni7CrMo2 Grade steel

IS 9175 : Part 31 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 31 20Ni7Mo2 Grade steel

IS 9175 : Part 32 : 1987 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 32 20NiCrMo2 Grade steel

IS 9175 : Part 33 : 1988 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 33 42Cr6V10 Grade steel

IS 9175 : Part 34 : 1986 Specification for Rationalized Steels for Automobile and Ancillary Industry, Mechanical and Physical Properties - Part 34 14CrNi6 Grade steel

IS 9178 : Part 1 : 1979 Criteria for design of steel bins for storage of bulk materials Part 1 General requirements and assessment of loads

IS 9178 : Part 1 : 1979 Criteria for design of steel bins for storage of bulk materials Part 1 General requirements and assessment of loads

IS 9178 : Part 2 : 1979 Criteria for design of steel bins for storage of bulk material Part 2 Design storage criteria

IS 9178 : Part 3 : 1980 Criteria for design of steel bins for storage of bulk materials Part 3 Bins designed for mass flow and funnel flow

IS 9178 : Part 3 : 1980 Criteria for design of steel bins for storage of bulk materials Part 3 Bins designed for mass flow and funnel flow

IS 9215 : 1979 Specification for Outdoor Steel Bins for Foodgrain Storage

IS 9294 : 1979 Specification for Cold-Rolled Stainless Steel Strips for Razor Blades

IS 9295 : 1983 Steel tubes for idlers for belt conveyors

IS 9415 : 1980 Method for determination of hardenability and grain size of tool steels by penetration fracture test

IS 9442 : 1980 Hot rolled steel plates, sheets and strips for manufacture of agricultural tillage discs

IS 9467 : 1980 Steel ingots and billets for production of rivet bars for structural purposes

IS 9468 : 1980 Steel ingots and billets for production of mild steel rivet bars for ship building

IS 9476 : 1980 Cold rolled steel strips for carbon steel razor blades

IS 9477 : 1980 Steel ingots and billets for hot rolled bars for the production of bright bars

IS 9485 : 1980 Cold-reduced and hot-rolled carbon steel sheet for porcelain enamelling

IS 9516 : 1980 Heat resisting steel

IS 9516 : 1980 Heat resisting steel

IS 9524 : 1980 Recommended procedure for repair welding of steel components by aluminothermic process

IS 9537 : Part 2 : 1981 Conduits for electrical installations:Part 2 Rigid steel conduits (superseding IS:1653)

IS 9550 : 2001 Bright Steel Bars - Specification

IS 9565 : 1995 Acceptance standards for ultrasonic inspection of steel castings

IS 9595 : 1996 Metal arc welding of carbon and carbon manganese steels - Recommendations

IS 9639 : 1980 Code of practice for visual inspection of low pressure welded steel gas cylinders during manufacture

IS 9683 : 1980 Carbon and low alloy steel forgings for fired and unfired pressure vessels

IS 9715 : 1981 Specification for steel visible indexing system cabinets

IS 9796 : 1981 Specification for Non-weathertight Steel Doors

IS 9879 : 1998 Method for Emission Spectrometric Analysis of Austentic and Ferritic Stainless Steels Point to Plane Technique

IS 9912 : 1981 Specification for Coal Tar Based Coating Materials and Suitable Primers for Protecting Iron or Steel Pipelines

IS 9954 : 1981 Pictorial Surface Preparation Standards for Painting of Steel Surfaces

IS 9962 : 1981 Specification for Steel Wire for Needles

IS 9962 : 1981 Specification for Steel Wire for Needles

IS 10007 : 1981 Specification for Lifeboats' Steel Blocks

IS 10019 : 1981 Specification for mild steel stays and fasteners

IS 10117 : 2000 Code of Practice for Passivation of Stainless Steel Articles, Industrial Equipments and Components Including Pipelines

IS 10121 : Part 1 : 1982 Specification for Metal Bone Screws - Mechanical Requirements and Methods of Test - Part 1 : Screws with Asymmetrical Thread, Variable Fitting (spherical), Stainless Steel

IS 10121 : Part II : 1982 Specification for Metal Bone Screws - Mechanical Requirements and Methods of Test - Part II : Screws with Asymmetrical Thread, Constant Fitting (spherical), Stainless Steel

IS 10138 : Part 1 : 1992 Macroscopic method for determination of non-metallic inclusion content in wrought steels Part 1 Blue fracture test method

IS 10138 : Part 2 : 1983 Macroscopic Methods for Determination of Non-metallic Inclusion Contents in Wrought Steels - Part 2 : Step Machined Test Method

IS 10138 : Part 3 : 1983 Macroscopic Methods for Determination of Non-metallic Inclusion Content in Wrought Steels - Part 3 : Magnetic Particle Inspection Method

IS 10178 : 1995 CO2 gas shielded metal arc welding of structural steels - Recommendations

IS 10181 : 1982 Method for determination of magnetic permeability of iron and steel

IS 10198 : 1982 Specification for Carbon Steel, Safety Razor Blades

IS 10206 : 1982 Methods of sampling steel wires

IS 10221 : 1982 Code of practice for coating and wrapping of underground mild steel pipelines

IS 10238 : 2001 Fasteners - Threaded Steel Fasteners - Step Bolts for Steel Structures - Specification

IS 10343 : 1999 Carbon and Low Alloy Steel Investment Castings for General Applications - Specification

IS 10345 : 1992 Flux grade limestone for use in steel plants

IS 10345 : 2004 Flux Grade Limestone for use in Iron and Steel Making - Specification

IS 10346 : 1991 Flux grade dolomite for use in steel plants

IS 10348 : 1982 Specification for Safety Footwear for Steel Plants

IS 10447 : 1983 Guidelines for utilization and disposal of solid waste from integrated steel plants

IS 10451 : 1983 Specification for steel sliding shutters (top hung type)

IS 10461 : Part 1 : 1994 Resistance to Inter-Granular Corrosion of Austenitic Stainless Steels - Method for Determination - Part 1 : Corrosion Test in Nitric Acid Medium by Measurement of Loss in Mass (Huey Test)

IS 10461 : Part 2 : 1994 Resistance to Intergranular Corrosion of Austenitic Stainless Steels - Method for Determination - Part 2 : Corrosion Test in a Sulphuric Acid/Copper Sulphate Medium in the Presence of Copper Turnings (Monypenny Strauss Test)

IS 10489 : 1983 Specification for Steel Dresser for Abrasive Wheels

IS 10604 : Part 1 : 1983 Machining allowances and tolerances for open die steel forgings Part 1 carbon and low alloy steel forgings

IS 10604 : Part 2 : 1983 Machining allowances and tolerances for open die steel forgings Part 2 High alloy steel forgings

IS 10605 : 1989 Steel globe valves (flanged and butt welded ends) for petroleum, petrochemical and allied industries - Specification

IS 10611 : 1983 Specification for Steel Gate Valves (Flanged and Butt-welded Ends) for Petroleum, Petrochemicals and Allied Industries

IS 10611 : 1983 Specification for Steel Gate Valves (Flanged and Butt-welded Ends) for Petroleum, Petrochemicals and Allied Industries

IS 10623 : 1983 Drop Weight Tear Test on Ferritic Steels and Line Pipe

IS 10626 : 1983 Dimensions of heald carrying rods and `C' shaped end loops of flat steel healds

IS 10631 : 1983 Stainless steel for welding electrode core wire

IS 10632 : Part 1 : 1983 Non Magnetic stainless steels for electrical applications Part 1 General requirements

IS 10632 : Part 2 : 1983 Non Magnetic stainless steels for electrical applications Part 2 Specific requirements for binding wire

IS 10632 : Part 3 : 1983 Non Magnetic stainless steels for electrical applications Part 3 Specific requirements for sheets, strips and plates for electrical appliances

IS 10663 : 2003/ISO 3823-1 : 1997 Dental Rotary Instruments - Steel and Carbid Burs

IS 10664 : 2003 /ISO 3823-2 : 1986 Dental Rotary Instruments - Steel and Carbide Finishing Burs

IS 10724 : 1990 Acceptancce standard for magnetic particle testing of steel casting

IS 10748 : 1995 Hot-rolled Steel Strip for Welded Tubes and Pipes - Specification

IS 10748 : 2004 Hot-Rolled Steel Strip for Welded Tubes and Pipes - Specification

IS 10790 : Part 1 : 1984 Methods of sampling of steel for prestressed and reinforced concrete part 1 Prestressing steel

IS 10790 : Part 2 : 1984 Methods of sampling of steel for prestressed and reinforced concrete Part 2 Reinforcing steel

IS 10794 : 1984 Mild steel wire for cottor pins

IS 10810 : Part 38 : 1984 Methods of test for cables:Part 38 Torsion test on galvanized steel wires for armouring

IS 10810 : Part 39 : 1984 Methods of test for cables:Part 39 Winding test on galvanized steel strips for armouring

IS 10810 : Part 40 : 1984 Methods of Test for Cables - Part 40 : Uniformity of Zinc Coating on Steel Armour

IS 10810 : Part 41 : 1984 Methods of test for cables:Part 41 Mass of zinc coating on steel armour

IS 10812 : 1992 Classification of sponge iron/direct reduced iron(DRI) fines/briquettes for steel making

IS 10842 : 1984 Evaluation Procedure for Y-groove Weld Crackability Test in Structural Steel

IS 10887 : 1983 Specification for Steel Wire Ropes for Winches and Ropeways Used in Forestry and Agriculture

IS 10887 : 2001 Steel Wire Ropes for Winches and Ropeways Used in Forestry and Agriculture - Specification

IS 10891 : Part 1 : 2001 Steel Wire Ropes for Aerial Ropeways - Specification - Part 1 : Haulage Ropes

IS 10891 : Part 1 : 1984 Specification for Steel Wire Ropes for Aerial Ropeways - Part 1 : Haulage Ropes

IS 10891 : Part 2 : 1986 Specification for Steel Wire Ropes for Aerial Ropeways - Part 2 : Track Ropes

IS 10989 : 1984 Specification for Cast or Forged Steel Check Valves (Flanged or Butt Welding Ends) for Petroleum, Petrochemicals, Chemicals and Allied Industries

IS 10989 : 1984 Specification for Cast or Forged Steel Check Valves (Flanged or Butt Welding Ends) for Petroleum, Petrochemicals, Chemicals and Allied Industries

IS 11083 : 1984 Method for Evaluation of Friction and Wear Properties of Materials Against Steel Surface

IS 11143 : 1984 Specification for Ground High Speed Steel Tool Bits

IS 11143 : 1984 Specification for Ground High Speed Steel Tool Bits

IS 11166 : 1993 Permissible deviations on dimensions, surface roughness and mass of steel castings made with investment casting process

IS 11169 : Part 1 : 1984 Steels for cold heading/cold extrusion application Part 1 Wrought carbon and low alloy steels

IS 11169 : Part 2 : 1989 Steels forcold heading/cold extrusion Part 2 Stainless steel

IS 11185 : 1984 Technical supply conditions for hot rolled and forged steel bars for use in machine tool industry

IS 11185 : 1984 Technical supply conditions for hot rolled and forged steel bars for use in machine tool industry

IS 11225 : 1985 Specification for Leather Safety Shoes for Women Workers in Mines and Steel Plants

IS 11281 : 2005 Manganese Ore for Use in Iron and Steel Making

IS 11281 : 1985 Manganese ore for the production of iron and steel making

IS 11286 : 1995 Corrosion resistant high alloy steel nickel base and cobalt base investment castings for severe applications

IS 11286 : 1995 Corrosion resistant high alloy steel nickel base and cobalt base investment castings for severe applications

IS 11304 : 1985 Code of practice for control of air pollution in iron and steel plants

IS 11323 : 1984 Specification for Steel Gate Valves for Use in Marine Pipe Work System

IS 11368 : Part 1 : 1985 Comparison of Indian and overseas classification and coding of welding filler materials Part 1 Flux coated mild steel and medium tensile steel electrodes for manual metal arc welding

IS 11368 : Part 1 : 1985 Comparison of Indian and overseas classification and coding of welding filler materials Part 1 Flux coated mild steel and medium tensile steel electrodes for manual metal arc welding

IS 11371 : 1985 Method for macroetch test for wrought steel products

IS 11384 : 1985 Code of Practice for Composite Construction in Structural Steel and Concrete

IS 11428 : Parts 1 to 3 : 1985 Specification for Wrought Carbon Steel Butt-Welding Pipe Fittings

IS 11513 : 1985 Hot-rolled carbon steel strip for cold rolling purpose

IS 11513 : 1985 Hot-rolled carbon steel strip for cold rolling purpose

IS 11585 : Part 1 : 1986 Specification for Insulated Stainless Steel Silos for Milk Storage - Part 1 : Capacities 60000 and 100000 Litres

IS 11587 : 1986 Structural weather resistant steels

IS 11626 : 1986 Recommended practice for ultrasonic testing and acceptance for forging quality steel blooms

IS 11626 : 2005 Recommended Practice for Ultrasonic Testing and Acceptance for Plain Carbon and Low Alloy Forging Quality Steel Blooms

IS 11630 : 2005 Method for Ultrasonic Testing of Steel Plates for Pressure Vessels and Special Applications

IS 11630 : 1986 - Method for Ultrasonic Testing of Steel Plates for Pressure Vessels and Special Applications

IS 11655 : 1986 Procedure for stray flux testing of ferrous magnetic seamless steel tubular products

IS 11699 : 1986 Specification for Steel Plug Valves for Petroleum, Petrochemical and Allied Industries

IS 11709 : 2007 Technical Delivery Conditions for Investment Castings of Steel

IS 11709 : 1995 Technical delivery conditions for investment castings of steel

IS 11714 : Parts 1 to 5 : 1986 Specification for Steel Tubes for Heat Exchangers

IS 11732 : 1995 Acceptance standards for dye penetrant inspection of steel castings

IS 11733 : 1986 Specification for steel wedge gate globe and check valves for petroleum, perochemical and allied industries (nominal size 50 mm and smaller)

IS 11758 : 1994 Precipitation hardening stainless steel castings

IS 11792 : 1986 Steel ball valve for the petroleum petrochemical and allied industries

IS 11792 : 1986 Steel ball valve for the petroleum petrochemical and allied industries

IS 11802 : 1986 Method of determination of diffusible hydrogen content of deposited weld metal from covered electrodes in welding mild and low alloy steels

IS 11906 : 1986 Recommendations for cement mortar lining for cast iron mild steel and ductile-iron pipes and fittings for transportation of water

IS 11952 : 1986 Steels for piston pins (Gudgeon pins)

IS 11991 : 1986 Recommended practice for flash butt welding of tubes, rods and other sections in carbon and alloy steel

IS 11999 : 2007 /ISO 10113 : 1991 Method for Determination of Plastic Strain Ratio 'r' for Steel Metals

IS 11999 : 1987 Method for determination of plastic strain ratio 'r' for steel sheets

IS 12093 : 1987 Code of practice for laying and fixing of sloped roof coverings using plain and corrugated galvanized steel sheets

IS 12117 : 1996 Norms for classification of steel foundries for quality assurance

IS 12145 : 1987 Quenched and tempered alloy steel forgings for pressure vessels

IS 12146 : 1987 Carbon manganese steel forgings for pressure vessels

IS 12211 : 1987 Micrographic method for assessing the distribution of carbides in tool steel and bearing steels using photomicrographs

IS 12262 : 1988 Trapezoidal steel wires for spring washers

IS 12313 : 1988 Specification for Hot-dip Terne Coated Carbon Steel Sheets

IS 12313 : 1988 Specification for Hot-dip Terne Coated Carbon Steel Sheets

IS 12367 : 1988 Specification for Cold-rolled Carbon Steel Strips/Coils for Manufacture of Welded Tubes

IS 12427 : 2001 Fasteners - Threaded Steel Fasteners - Hexagon Head Transmission Tower Bolts - Specification

IS 12450 : Part 1 : 1988 Steel headframes for mines Part 1 Principles of load computation and applicable factors of safety

IS 12457 : 1988 Code of practice for evaluation repairs and acceptance limits of surface defects in steel plates, and wide flats

IS 12586 : 1988 Brazed Low Carbon Steel Gas Cylinders Not Exceeding 13 Litre Water Capacity - Specification

IS 12586 : 1988 Brazed Low Carbon Steel Gas Cylinders Not Exceeding 13 Litre Water Capacity - Specification

IS 12591 : 1988 Specification for Cold Reduced Tin Free Steel in Sheet Form

IS 12591 : 2006 /ISO 11950 : 1995 Cold-Reduced Electrolytic Chromium/Chromium Oxide - Coated Steel

IS 12594 : 1988 Hot-dip Zinc Coating on Structural Steel Bars for Concrete Reinforcement - Specification

IS 12594 : 1988 Hot-dip Zinc Coating on Structural Steel Bars for Concrete Reinforcement - Specification

IS 12620 : 1989 Seamless Steel Tubes for Manufacturing High Pressure Gas Cylinders - Specification

IS 12620 : 1989 Seamless Steel Tubes for Manufacturing High Pressure Gas Cylinders - Specification

IS 12643 : 1989 Corrosion Protection of Steel by Fibreglass Reinforced Polyester Lining - Code of Practice

IS 12658 : 1989 Grinding Media Rolled/Forged Carbon and Carbon-Chromium Steels - Specification

IS 12694 : 1993 /ISO 8369 : 1986 Large diameter steel wire ropes

IS 12753 : 1989 Electrogalvanized Coatings on Round Steel Wire - Specification

IS 12778 : 2004 Hot Rolled Parallel Flange Steel Sections for Beams, Columns and Bearing Piles - Dimensions and Section Properties

IS 12778 : 1989 Hot rolled steel parallel flange beam and column sections - Dimensions

IS 12791 : 1989 High carbon chromium (bearing) steel tubes for the manufacture of bearing races

IS 12817 : 1997 Specification for stainless steel butt hinges

IS 12817 : 1997 Specification for stainless steel butt hinges

IS 12843 : 1989 Tolerances for erection of steel structures

IS 12938 : 1990 Acceptance standards for radiographic inspection of steel castings

IS 12968 : 1991 Steel castings for crankshafts for marine engines

IS 12968 : 1991 Steel castings for crankshafts for marine engines

IS 12986 : Part 1 : 1990 Biogas Plants - Glass Fibre Reinforced Polyester Resin Gas Holders - Specification - Part 1 : With Steel Frame

IS 13015 : 1991 Macroetch testing, inspection and rating of steel products

IS 13040 : 1991 Dolly blocks for use in steel body repairs - General requirements

IS 13058 : 1991/ISO 7592 : 1983 Calibrated round steel link lifting chains - Guidelines for proper use and maintenance

IS 13093 : 2002 Sheet Metal Body Repair Steel Hammers - General Requirements

IS 13093 : 1991 Sheet metal body repair steel hammers - General requirements

IS 13147 : 1991 Black Oxide Coating on Stainless Steel Parts - Specification

IS 13148 : Part 1 : 1999 /ISO 5049-1 : 1994 Mobile Equipment for Continuous Handling of Bulk Materials - Part 1 : Rules for the Design of Steel Structure

IS 13177 : 1991 Passivation of stainless steel parts

IS 13190 : 1991 Recommended practice for eddy current examinationn by rotating probe method of round steel bars

IS 13212 : 1991 Blackoxide coatings for iron and steel parts

IS 13258 : 1991 welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gas - Code of practice for inspection and reconditioning of used LPG cylinders

IS 13316 : 1992 Welded Austenitic Stainless Steel Tubes for Heat Exchangers for the Sugar Industry - Specification

IS 13387 : 1992 Tool steel forgings for metal forming

IS 13387 : 1992 Tool steel forgings for metal forming

IS 13417 : 1992 Code of practice for heat treatment of steels

IS 13505 : 1992 Centrifugally cast high alloy steel and nickel base tubing for pressure application at high temperature

IS 13519 : 1992 Guidelines for inspection of fixed steel offshore structures during fabrication and installation

IS 13629 : 1992 Textile machinery - Stainless steel drying cylinders used in textile processing - Specification

IS 13629 : 2004 Textiles Machinery - Stainless Steel Drying Cylinders used in Textile Processing - Specification

IS 13694 : 1993 Code of practice for fire safety in iron and steel industries

IS 13718 : Part 2 : 1993 Horology - Watch straps Part 2 Stainless steel - Specification

IS 13752 : 1993 Guidelines for Reporting Sequence of Elements in Steel and Pig Iron and Mechanical Properties in Steels

IS 13839 : 1993 Sponge Iron/DRI Fines/briquettes for Steel Making - Specification

IS 13869 : 1993 /ISO 10092 : 1990 High Breaking Load Steel Wire Ropes - Specifications

IS 13905 : 1993 Hot Briquetted sponge iron (HBI) for steel making

IS 13915 : 1994 Shipbuilding - Ships' steel weathertight doors - Specification

IS 13926 : 1994/ISO 6971 : 1982 Welded steel type cranked link drag chains and chain wheels

IS 13927 : 1994/ISO 6972 : 1982 Welded steel type cranked link mill chains and chain wheels

IS 13929 : 1993 Stainless Steel Decking Plates for Cane mud Filters - Specification

IS 13929 : 1993 Stainless Steel Decking Plates for Cane mud Filters - Specification

IS 13983 : 1994 Specification for stainless steel sinks for domestic purposes

IS 13983 : 1994 Specification for stainless steel sinks for domestic purposes

IS 14103 : 1994 Deepwell handpumps - Components - Mild steel - Specification

IS 14105 : 1994 Deepwell Handpumps - Components - Stainless Steel - Specification

IS 14105 : 1994 Deepwell Handpumps - Components - Stainless Steel - Specification

IS 14246 : 1995 Continuously pre-painted galvanised steel sheets and coils

IS 14331 : 1995 Steels for high temperature bolting applications

IS 14491 : 1997 Low carbon high strength cold rolled steel sheets and coils for cold forming

IS 14598 : 1998 Heat treatment of maraging steel - Code of practice

IS 14650 : 1999 Carbon Steel Cast Billet Ingots, Billets, Blooms and Slabs for Re-Rolling Purposes - Specification

IS 14652 : 1999 18 Percent Nickel Maraging Steel Bars and Rods - Specification

IS 14696 : 2000 Transmission Steel Roller Chains and Chain Wheels for Oil Field Applications - Specification

IS 14698 : 1999 Carbon and Low Alloy Steel Billets, Blooms, Slabs and Bars for Manufacture of Shell Bodies and Proof Shots Used in Defence Services - Specification

IS 14756 : 2000 Stainless Steel Cooking Utensils - Specification

IS 14895 : 2000 Ophthalmic Instruments - Spuds, Foreign Body - Waltons Sizes 1 and 1.5 mm Wide, Stainless Steel - Specification

IS 15103 : 2002 Fire Resistant Steel - Specification

IS 15104 : Part 2 : 2002/ISO 8442-2 : 1998 Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 2 : Requirements for Stainless Steel and Silver-Plated Cutlery

IS 15143 : 2002 Conveyor Belting of Elastomeric and Steel Cord Construction for Underground Mines and Such Other Harzardous Applications - Specification

IS 15155 : 2002 Bar/Wire Wraped Steel Cylinder Pipes With Mortarlining and Coating (Including Specials) -- Specification

IS 15184 : 2002 Bicycles - Steel Balls - Specification

IS 15191 : 2002 Forged Steel Components for Use With Grade T (8) Chain and Chain Slings - Specification

IS 15337 : 2003 Coal Tar Based Anticorrosion Tape for Protection of Underground Mild Steel Pipelines - Specification

IS 15379 : 2003 /ISO 9904 : 2000 Textile Machinery and Accessories - Steel Pins For Spinning Preparatory and Spinning Machinery

IS 15391 : 2003 Cold Rolled Non-Oriented Electrical Steel Sheet and Strip - Semi-Processed Type - Specification

IS 15391 : 2003 Cold Rolled Non-Oriented Electrical Steel Sheet and Strip - Semi-Processed Type - Specification

IS 15426 : 2004 /ISO 14250 : 2000 Steel - Metallographic Characterization of Duplex Grain Size and Distributions

IS 15427 : 2004 Conveyor Belting of Elastomeric and Steel Cord Construction for General Material Handling - Specification

IS 15507 : 2004 Basic Insulating Coating Materials for Application in Tundish Used in Steel Plants - Specification

IS 15508 : 2004 Refractory Mass (Basic Gunning) for Steel Plant Application - Specification

IS 15637 : 2006 Welded Stainless Steel Cylinders for Liquefied Petroleum Gases (LPG) from 0.5 litre to 250 litre Water Capacity - Specification

IS 15637 : 2006 Welded Stainless Steel Cylinders for Liquefied Petroleum Gases (LPG) from 0.5 litre to 250 litre Water Capacity - Specification

IS 15647 : 2006 Hot Rolled Steel Narrow Width Strip for Welded Tubes and Pipes

IS 15760 : Part 1 : 2007 Textile Machinery and Accessories - Main Dimensions of Flat Steel Healds with Open End Loops - Part 1 : C-Shaped End Loops

IS 15760 : Part 2 : 2007 /ISO 11677-2 : 1994 Textile Machinery and Accessories - Main Dimensions of Flat Steel Healds with Open End Loops - Part 2 : J-Shaped end Loops

IS 15760 : Part 3 : 2007 /ISO 11677-3 : 1995 Textile Machinery and Accessories - Main Dimensions of Flat Steel Healds with Open End Loops - Part 3 : Carrying Rods for Healds with C- and J-Shaped end Loos

IS 15774 : 2007 Sponge Iron/Directed Reduced Iron (DRI) Hot Briquetted Iron (HBI) and Cold Briquetted Iron (CBI) for Steel Making - Specification

IS/ISO 16160 : 2005 Continuously Hot-Rolled Steel Sheet Products - Dimensional and Shape Tolerances

IS/ISO 16162 : 2005 Continuously Cold-Rolled Steel Sheet Products - Dimensional and Shape Tolerances

IS/ISO 16163 : 2005 Continuously Hot-Dipped Coated Steel Sheet Products - Dimensional and Shape Tolerances

Is Code for Steel

Documents