7/26/2019 Invacare 9000 Series user Manual
1/88
Service Manual
DEALER:Keep this manual. The procedures in this manual must beperformed by a qualified technician only.
For more information regarding
Invacare products, parts, and services,
please visit www.invacare.com
9000 Series
9000 SL
9000 XT
9000 XDT
9000XT Recliner
7/26/2019 Invacare 9000 Series user Manual
2/88
REFERENCE DOCUMENTS
9000 Series 2 Part No. 1076155
WARNINGTHE PROCEDURES IN THIS SERVICE MANUAL MUST BE
PERFORMED BY A QUALIFIED TECHNICIAN.
DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT
FIRST READING AND UNDERSTANDING (1) THE OWNERSOPERATOR AND MAINTENANCE MANUAL AND (2) THE SERVICE
MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE
WARNINGS, CAUTIONS AND INSTRUCTIONS, CONTACT
INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO
SERVICE OR OPERATE THIS EQUIPMENT. OTHERWISE, INJURY
OR DAMAGE MAY RESULT.
REFERENCE DOCUMENTSRefertothetablebelowforpartnumbersofadditionaldocumentswhicharereferencedinthismanual.
MANUAL PART NUMBER
9000 Series Owners Operator and Maintenance Manual 1056953
NOTE:Updatedversionsofthismanualareavailableonwww.invacare.com.
7/26/2019 Invacare 9000 Series user Manual
3/88
TABLE OF CONTENTS
Part No. 1076155 3 9000 Series
TABLE OF CONTENTSREFERENCE DOCUMENTS ................................................................. 2
SPECIAL NOTES ................................................................................ 6
LABEL LOCATION ............................................................................ 7
TYPICAL PRODUCT PARAMETERS .................................................... 8SECTION 1GENERAL GUIDELINES ................................................. 12
Stability - All Models ................................................................................................................................12
Stability - Recliner Models Only.......................................................................................................13
Anti-Tippers...............................................................................................................................................13
Operating Information.............................................................................................................................13
Tire Pressure.............................................................................................................................................14
Weight Training ........................................................................................................................................14
Weight Limitation.....................................................................................................................................14
SECTION 2SAFETY INSPECTION/TROUBLESHOOTING .................... 15
Checklist.....................................................................................................................................................15
Troubleshooting .............................................................................................................16
Maintenance...............................................................................................................................................16
Maintenance Safety Precautions .......................................................................................................16Suggested Maintenance Procedures ................................................................................................16
SECTION 3SEAT AND BACK ......................................................... 18
Adjusting Back Angle ...............................................................................................................................18
Adjusting Back Height..............................................................................................................................19
9000 SL without Adjustable Back Angle Option ..........................................................................199000 SL with Adjustable Back Angle Option and 9000 XT/XDT ............................................20
Adjusting Seat Width...............................................................................................................................20
Adjusting Seat Depth...............................................................................................................................23
9000XT Model......................................................................................................................................239000 XDT and 9000 SL......................................................................................................................24
SECTION 4FRONT CASTERS ......................................................... 26
Front Caster Mounting Adjustments...................................................................................................26
Converting from Trailing to Leading or Leading to Trailing Casters...........................................27
Repositioning/Replacing Cam.................................................................................................................28
SECTION 5SEAT TO FLOOR ........................................................... 29
Changing Seat-to-Floor Height/Seat-to-Floor Angle........................................................................29
Super Low Frame Style.......................................................................................................................31Adult/Tall Frame Style.........................................................................................................................31Adult/Hemi Frame Styles ...................................................................................................................32
7/26/2019 Invacare 9000 Series user Manual
4/88
TABLE OF CONTENTS
9000 Series 4 Part No. 1076155
TABLE OF CONTENTS24-Inch Rear Wheels and 8-Inch Front Casters .....................................................................3224-Inch Rear Wheels and 6-Inch Front Casters .....................................................................3722-Inch Rear Wheels and 8-Inch Front Casters .....................................................................3922-Inch Rear Wheels and 6-Inch Front Casters .....................................................................43
20-Inch Rear Wheels and 8-Inch Front Casters .....................................................................4620-Inch Rear Wheels and 6-Inch Front Casters .....................................................................48
SECTION 6REAR WHEELS ............................................................. 52
Removing/Installing Rear Wheels .........................................................................................................52
Quick-Release Axles ...........................................................................................................................52Permanent Axles..................................................................................................................................53
Models without Offset Axle Option ..........................................................................................53Models with Offset Axle Option ................................................................................................54
Adjusting Quick-Release Axle ...............................................................................................................57
Adjusting Wheelbase Length .................................................................................................................57SECTION 7RECLINER ................................................................... 58
Replacing Release Handle .......................................................................................................................58
Adjusting Cable Assembly Tension ......................................................................................................59
Replacing Cable Assembly......................................................................................................................60
Disconnecting/Connecting Lower Cable Assembly .........................................................................61
Disconnecting .......................................................................................................................................61Connecting ............................................................................................................................................61
Replacing Threaded Sector ....................................................................................................................64
Replacing Locking Rod ............................................................................................................................65Replacing Back Tube................................................................................................................................65
Removing/Installing Spring Lift Mechanism .........................................................................................67
Removing ...............................................................................................................................................67Installing..................................................................................................................................................68
Replacing Recliner Tube..........................................................................................................................69
Adjusting Seat Width...............................................................................................................................71
Adjusting Seat Depth...............................................................................................................................74
Removing/Installing Rear Wheels .........................................................................................................75
With Patient Operated Wheel Locks.............................................................................................75With Attendant Operated Wheel Locks .......................................................................................75
Using/Adjusting Wheel Locks................................................................................................................75
Using Attendant Operated Wheel Locks.......................................................................................75Adjusting Attendant Operated Wheel Locks................................................................................76
Changing Seat-to-Floor Height..............................................................................................................77
Installing Anti-Tippers..............................................................................................................................78
7/26/2019 Invacare 9000 Series user Manual
5/88
Part No. 1076155 5 9000 Series
SECTION 8ANTI-TIPPERS/WHEEL LOCKS ....................................... 80
Installing/Adjusting Anti-tippers ............................................................................................................80
Installing Anti-Tippers .........................................................................................................................80Adjusting Anti-Tippers........................................................................................................................81
Using/Adjusting Disk Wheel Locks ......................................................................................................82
Using Patient Operated Disk Wheel Locks...................................................................................82Adjusting Patient-Operated Wheel Locks .....................................................................................83
Installing Wheel Lock Shoe Extensions...............................................................................................85
LIMITED WARRANTY ..................................................................... 87
7/26/2019 Invacare 9000 Series user Manual
6/88
SPECIAL NOTES
9000 Series 6 Part No. 1076155
SPECIAL NOTESSignalwordsareusedinthismanualandapplytohazardsorunsafepracticeswhichcouldresultinpersonalinjuryorpropertydamage.Refertothefollowingtablefordefinitionsofthesignalwords.
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO
CHANGE WITHOUT NOTICE.WHEELCHAIR USER
As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of
wheelchairs to meet many needs of the end user. However, final selection of thetype of wheelchair to be used by an individual rests solely with the user and his/herhealthcare professional capable of making such a selection.
WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT RESTRAINTS
Wheelchair users should NOT be transported in vehicles of any kind while in
wheelchairs. As of this date, the Department of Transportation has not approvedany tie-down systems for transportation of a user while in a wheelchair, in a moving
vehicle of any type.It is Invacares position that users of wheelchairs should be transferred into
appropriate seating in vehicles for transportation and use be made of the restraintsmade available by the auto industry. Invacare cannot and does not recommend any
wheelchair transportation systems.
SEAT POSITIONING STRAP
Regarding seat positioning straps, it is the obligation of the DME dealer, therapists
and other healthcare professionals to determine if a seat positioning strap isrequired to ensure the safe operation of this equipment by the user. Serious injurycan occur in the event of a fall from a wheelchair.
SIGNAL WORD MEANING
DANGER Danger indicates an imminently hazardous situation which, if not avoided, will result indeath or serious injury.
WARNING Warning indicates a potentially hazardous situation which, if not avoided, could result indeath or serious injury.
CAUTION Caution indicates a potentially hazardous situation which, if not avoided, may result inproperty damage.
7/26/2019 Invacare 9000 Series user Manual
7/88
LABEL LOCATION
Part No. 1076155 7 9000 Series
IMPORTANT NOTICE
The wheel locks on this wheelchair have been
pre-set at the factory to comply with theVeterans Admini strati on functi onal Standard
8320.01 of the Federal Register, paragraph3.2.4.5.3. If these wheel locks do not meet
your needs, follow instructions below.
! CAUTION
Any wheel lock adjustments should embed
wheel lock shoe at least 1/8" into tire whenlocked (3/16" on pneumatic tires).
INSTRUCTIONS FOR WHEEL
LOCK ADJUSTMENTS
1. Loosen wheel lock mounting fastener,which runs through mounting bracket and
frame.2. Slide clamp toward rear wheel until wheel
lock shoe is embedded into tire material atleast 1/8" when handle is engaged to the
lock position (3/16" for pneumatic tires).3. Tighten mounting fastener to secure
mounting bracket in desired location andrecheck lock shoe embedding.
4. Inspect for correct locking action BEFORE
actual use.00078X021-0394
Refer to Owner's Manual
for proper anti-tipper
setting. 1085379
WARNING
WARNINGDETENT BALLS MUST BE SECURE-
LY SEATED IN RECESSED AREAS
OF AXLE BUSHINGS. ENSURE
THAT PLUNGER PIN IN HEAD END
OF AXLE IS FULLY RELEASED.
KEEP DETENT BALLS CLEAN.
1001948
CAUTION
DO NOT recline without occupant. When the
chair is not occupied the back will raise abrup-
tly. Keep clear of the chair back when raising
or lowering to avoid injury.1023096
CAUTIONSERVICE OF SPRING
LIFT MECHANISM TO
BE PERFORMED BY
PROPERLY TRAINED
AUTHORIZED SERVICE
PERSONNEL ONLY.
1022642
WARNINGDO NOT OPERATE WITHOUT
THE ANTI-TIP TUBES
INSTALLED.REV. 5/98 P/N 60106X144
WARNINGDO NOT OPERATE WITHOUT
THE ANTI-TIP TUBES
INSTALLED.REV. 5/98 P/N 60106X144
LABEL LOCATIONCrossmember
Lower
Frame
Tube
9000 XDT Only
NOTE:Onalladjustableantitippers
9000 XT Recliner Models Only
Models with
Quick-Release Axles Only
7/26/2019 Invacare 9000 Series user Manual
8/88
TYPICAL PRODUCT PARAMETERS
9000 Series 8 Part No. 1076155
TYPICAL PRODUCT PARAMETERS
*NOTE:Theseoptionsarestandardforthismodel.
**NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.
9000 SL
OVERALL WIDTH 23 or 25 inches
OVERALL DEPTH (WITH RIGGINGS) 43 inches
SEAT WIDTH 16, 18 or 20 inches
SEAT DEPTH 16 or 18 inches
** SEAT-TO-FLOOR
TALL/ADULT:ADULT/HEMI:SUPER HEMI:
N/A15 to 19 in 1-inch incrementsN/A
BACK STYLE Sectional* - height adjustable in 1-inch incrementsAdjustable angle - 85 to 110 in 5 increments
BACK HEIGHT Ranges of 15 to 17 inches or 17 to 19 inches(adjustable in 1-inch increments)
ARM STYLES Swing Back* Space Saver*, Desk* or full length in
Fixed* or Adjustable HeightSwing Back Removable, Conventional, AdjustableHeight (Adjustable back angle style)
FRONT RIGGINGS Swingaway footrests and elevating legrests
REAR AXLE Permanent* and quick-release
REAR WHEELS 20, 22 and 24*-inch composite; Urethane*, pneumaticor pneumatic-flat free insert
HANDRIMS Composite* and aluminum, steel
WHEEL LOCKS Toggle lock -push or pull
CASTER SIZE 6 x 1-inch Urethane, 8 x 1-inch* Urethane,
8x1-inch solid rubber, and 8x1-inch pneumatic orpneumatic flat-free insert
UPHOLSTERY Black nylon*, black vinyl
FRAME COLORS Chrome* and colors
WEIGHT (18 X 16 INCH SEAT) 33 lbs
SHIPPING WEIGHT (APPROX.)
16 X 16 INCH SEAT FRAME WITH COMPLETEPACKAGE:
43 lbs
WEIGHT LIMIT 250 lbs (114 kg)
7/26/2019 Invacare 9000 Series user Manual
9/88
TYPICAL PRODUCT PARAMETERS
Part No. 1076155 9 9000 Series
*NOTE:Theseoptionsarestandardforthismodel.
**NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.
Theseheights
can
vary
+/
inch
due
to
tire
wear
and
manufacturing
tolerances.
9000 XT
OVERALL WIDTH 21, 22, 23, 25, 27 or 29 inches
OVERALL DEPTH (WITH RIGGINGS) 43 inches
SEAT WIDTH 14, 15, 16, 18, 20 or 22 inches
SEAT DEPTH 16, 17, or 18 inches
** SEAT-TO-FLOOR
TALL/ADULT:ADULT/HEMI:SUPER HEMI:
N/A15 to 19 in 1-inch increments13 and 14 inches
BACK STYLE Height adjustable* - 1-inch incrementsAdjustable angle - 85 to 110 in 5 increments
BACK HEIGHT Ranges of 15 to 17 inches or 17 to 19 inches(adjustable in 1-inch increments)
ARM STYLES Swing back removable, space saver* or conventionalin desk* or full length and in fixed* or adjustableheight
FRONT RIGGINGS Swingaway footrests and elevating legrests
REAR AXLE Permanent* and quick-release
REAR WHEELS 20, 22 and 24*-inch composite; Urethane*, pneumaticor pneumatic-flat free insert
HANDRIMS Composite*, aluminum, steel and plastic coated
WHEEL LOCKS Toggle lock -push or pull
CASTER SIZE 6 x 1-inch Urethane, 8 x 1-inch* Urethane,8x1-inch solid rubber, and 8x1-inch pneumatic orpneumatic flat-free insert, 8x1-inch semi pneumatic
UPHOLSTERY Black nylon*, black sail cloth, heavy vinyl
FRAME COLORS Chrome* and colors
WEIGHT (18 X 16 INCH SEAT) 31 lbs
SHIPPING WEIGHT (APPROX.)
16 X 16 INCH SEAT FRAME WITH COMPLETEPACKAGE
41 lbs
WEIGHT LIMIT 250 lbs (114 kg)
7/26/2019 Invacare 9000 Series user Manual
10/88
TYPICAL PRODUCT PARAMETERS
9000 Series 10 Part No. 1076155
*NOTE:Theseoptionsarestandardforthismodel.
**NOTE:Theseattofloorheightsarebasedonpneumatictiresandpneumatictireswithflatfreeinserts.Ifwheelchairisequippedwithurethanetires,subtractinchfromthemeasurementslistedabove.Allheightsaremeasuredwithproperlyinflatednewtires.Theseheightscanvary+inchduetotirewear.
9000 XT RECLINER
OVERALL WIDTH 23, 25, 27, 28, 29 or 31 inches
OVERALL DEPTH (WITH RIGGINGS) 46 inches
SEAT WIDTH 14, 16, 18, 19, 20 or 22 inches
SEAT DEPTH 16, 17, or 18 inches
SEAT-TO-FLOOR**
TALL/ADULT:ADULT/HEMI:SUPER HEMI:
17 to 19 inches in 1-inch incrementsN/AN/A
BACK STYLE Reclining
BACK HEIGHT 23 or 24 inches
ARM STYLES ConventionalDesk* or full length and in fixed* or adjustable height
FRONT RIGGINGS Swingaway footrests and elevating legrests
REAR AXLE Permanent
REAR WHEELS 20, 22 and 24*-inch composite; Urethane*, pneumaticor pneumatic-flat free insert
HANDRIMS Composite*, aluminum, steel and plastic coated
WHEEL LOCKS Toggle lock - push or pull
CASTER SIZE 8 x 1-inch* Urethane, 8x1-inch solid rubber, and8x1-inch pneumatic or pneumatic flat-free insert,8x1-inch semi pneumatic
UPHOLSTERY Heavy vinyl, light vinyl, nylon, sail cloth
FRAME COLORS Chrome and colors
WEIGHT 50 lbs
SHIPPING WEIGHT (APPROX.) 60 lbs18x17-inch seat frame with complete package
WEIGHT LIMIT 250 lbs (114 kg)
7/26/2019 Invacare 9000 Series user Manual
11/88
TYPICAL PRODUCT PARAMETERS
Part No. 1076155 11 9000 Series
*NOTE:Theseoptionsarestandardforthismodel.
**NOTE:Theseattofloorheightsarebasedonpneumatictiresandpneumatictireswithflatfreeinserts.Ifwheelchairisequippedwithurethanetires,subtractinchfromthemeasurementslistedabove.Allheightsaremeasuredwithproperlyinflatednewtires.Theseheightscanvary+
inch
due
to
tire
wear.
9000 XDT
OVERALL WIDTH 23, 25, 27 or 29 inches
OVERALL DEPTH (WITH RIGGINGS) 45 inches
SEAT WIDTH 16, 18, 20 or 22 inches
SEAT DEPTH 16, 17, 18, 19 and 20 inches
SEAT-TO-FLOOR**
TALL/ADULT:ADULT/HEMI:SUPER HEMI:
17, 19 and 21 inchesN/AN/A
BACK STYLE Height adjustable - 1-inch increments
BACK HEIGHT Ranges of 15 to 17 inches or 17 to 19 inches(adjustable in 1-inch increments)
ARM STYLES Swing back or removable, space saver* or conven-tional, desk* or full length and in fixed* or adjustableheight
FRONT RIGGINGS Swingaway footrests and elevating legrests
REAR AXLE Permanent
REAR WHEELS 24*-inch composite, urethane*, pneumatic or pneu-matic-flat free insert
HANDRIMS Steel*, aluminum and plastic coated
WHEEL LOCKS Toggle lock - push or pull
CASTER SIZE 8 x 1-inch* Urethane, 8x1-inch solid rubber, and8x1-inch pneumatic or pneumatic flat-free insert,8x1-inch semi pneumatic
UPHOLSTERY Black nylon, black sail cloth, heavy vinyl
FRAME COLORS Chrome and colors
WEIGHT 36 lbs
SHIPPING WEIGHT (APPROX.) 46 lbs16x16-inch seat frame with complete package
WEIGHT LIMIT 350 lbs (154 kg)
7/26/2019 Invacare 9000 Series user Manual
12/88
SECTION 1GENERAL GUIDELINES
9000 Series 12 Part No. 1076155
SECTION 1GENERAL GUIDELINES
WARNINGSECTION 1 - GENERAL GUIDELINES contains important information for the safe
operation and use of this product.DO NOT use this product or any available
optional equipment without first completely reading and understanding theseinstructions and any additional instructional material such as Owners Manuals,Service Manuals or Instruction Sheets supplied with this product or optionalequipment. If you are unable to understand the Warnings, Cautions or Instructions,
contact a healthcare professional, dealer or technical personnel before attemptingto use this equipment. Otherwise, injury or damage may occur.
Stability - All Models
Theseatdepth,backheight/angle,seatangle,size/positionofthefrontcasters,
size/positionoftherearwheels,antitippermodel,aswellastheuserconditiondirectlyrelatetothestabilityofthewheelchair.Anychangetoone(1)oranycombinationoftheten(10)maycausethewheelchairtodecreaseinstability.TheseadjustmentsMUSTbeperformedbyaqualifiedtechnician.
Thevariousseattofloorheightsrequirespecificsettingsdependingonrearwheelsize,rearwheelposition,frontcastersize/positionanddesiredseattofloorangle.TheseadjustmentsMUSTbeperformedbyaqualifiedtechnician.
NOTE:Whenchangestothelefthandcolumnoccur,followacrossthechartandrefertotheX
proceduretomaintaintheproperstability,
safetyandhandlingofthewheelchair. B
ACKHEIGHT
SEATDEPTH
B
ACKANGLE
SEA
TINGSYSTEM
CASTERSIZE
CASTERPOSITION
WHEELSIZE
WH
EELPOSITION
USE
RCONDITION
W
HEELLOCKS
A
NTI-TIPPERS
BACK HEIGHT X X X X X X X N/A N/A N/A
SEAT DEPTH X X X X X X X N/A N/A N/A
BACK ANGLE X X X X X X X N/A N/A N/A
SEATING SYSTEM X X X X X X X X N/A N/A
CASTER SIZE X N/A X N/A X X X N/A X X
CASTER POSITION X N/A X N/A X X X N/A X X
WHEEL SIZE X N/A X N/A X X X N/A X X
WHEEL POSITION X N/A X N/A X X X N/A X X
USER CONDITION X X X X X X X X N/A N/ASEAT HEIGHT X N/A X X X X X X N/A X X
7/26/2019 Invacare 9000 Series user Manual
13/88
SECTION 1GENERAL GUIDELINES
Part No. 1076155 13 9000 Series
Stability - Recliner Models Only
ALWAYSmakesurethatthewheelchairisstablebeforeusingthereclineroption.
Ensurethespreaderbarisattachedandsecuredbeforeusingthe9000XTRecliner.
ALWAYSreturnthebacktotheuprightpositionbeforeliftingthewheelchair.
LiftKitModelsonly BothspringliftmechanismsMUSTbeoperationalbeforeusingthe
recliner.DONOToperatethereclineroptionifonlyone(1)ofthespringliftmechanismsisoperational.
Anti-Tippers
Antitippersarespecifictothedifferentseattoflooranglesand/orseattofloorheights.RefertothechartsinInstalling/AdjustingAntitippersonpage 80forcorrectusageandadjustment.Iftheserequirementscannotbeachieved,DONOTusethewheelchair.Contactaqualifiedtechnician.Ifchangingtheseattofloorheightwithorwithoutachangetoseattofloorangle,thecorrectantitippersMUSTbeusedtomaintaina1to
2inchgroundclearance.
Seattofloorangleof0or3:Ifsoequipped,antitippersMUSTbeattachedatalltimes.Inasmuchastheantitippersareanoptionfor0or3onthiswheelchair(youmayorderwithorwithouttheantitippers),Invacarestronglyrecommendsorderingtheantitippersasasafeguardforthewheelchairuser.
Seattofloorangleof6:Ifchangingtheseattofloorangleto6,antitippersMUSTbeinstalled.
Operating Information
InvacareproductsarespecificallydesignedandmanufacturedforuseinconjunctionwithInvacareaccessories.Accessoriesdesignedbyothermanufacturershavenotbeentested
byInvacareandarenotrecommendedforusewithInvacareproducts.
Unlessotherwisenoted,allserviceandadjustmentshouldbeperformedwhilethewheelchairisunoccupied.
Whencleaningrearcaneorhandgripareasuseonlyacleantowellightlydampenedwithcoolwater.Verifythatgripsaredrypriortouse.Useofsoaporammoniabasedcleaningsolutionswillresultinthehandgripsslidingoffthecaneassembly.Failuretoobservethiswarningmayresultininjurytotheuserorbystanders.
Ifthewheelchairisexposedtoextremetemperature(above100Forbelow32F),highhumidityand/orbecomeswet,ensurepriortousethatthehandgripsdonottwistonthehandle.Otherwise,damageorinjurymayoccur.
Avoidstoringorusingthewheelchairnearopenflameorcombustibleproducts.Seriousinjuryordamagetopropertymayresult.
7/26/2019 Invacare 9000 Series user Manual
14/88
SECTION 1GENERAL GUIDELINES
9000 Series 14 Part No. 1076155
DONOTattempttoliftthewheelchairbyanyremovable(detachable)parts.Liftingbymeansofanyremovable(detachable)partsofthewheelchairmayresultininjurytotheuserordamagetothewheelchair.
9000XTReclineronly DONOTusethespreaderbartoliftthewheelchair.
DONOTstandontheframeofthewheelchair.
DONOT
use
the
footplate
as
aplatform.
When
getting
in
or
out
of
the
wheelchair,
make
surethatthefootplatesareintheupwardposition.
NEVERusequickreleaseaxlesonthe9000XT(modelswithoffsetaxleoptiononly),9000XDTor9000XTReclinerwheelchairs.
Tire Pressure
DONOTusethewheelchairunlessithasthepropertirepressure(p.s.i.).DONOToverinflatethetires.Failuretofollowthesewarningsmaycausethetiretoexplodeandcausebodilyharm.Therecommendedtirepressureislistedonthesidewallofthetire.
Weight Training
Invacaredoesnotrecommendtheuseofitswheelchairsasaweighttrainingapparatus.Invacarewheelchairshavenotbeendesignedortestedasaseatforanykindofweighttraining.Ifoccupantusessaidwheelchairasaweighttrainingapparatus,Invacareshallnotbeliableforbodilyinjuryordamagetothewheelchairandthewarrantyisvoid.
Weight Limitation
The9000SL,9000XT,and9000XTReclinerwheelchairshaveaweightlimitationof250lbs(114kg).The9000XDTwheelchairhasaweightlimitationof350lbs(159kg).
7/26/2019 Invacare 9000 Series user Manual
15/88
SECTION 2SAFETY INSPECTION/TROUBLESHOOTING
Part No. 1076155 15 9000 Series
SECTION 2SAFETYINSPECTION/TROUBLESHOOTINGNOTE:Initialadjustmentsshouldbemadetosuittheenduserspersonalbodystructureneedsandpreference.Afterinitialsetup,performtheseprocedureseverytimethewheelchairisserviced.
Checklist
Ensurethatthewheelchairrollsstraight(noexcessivedragorpulltooneside).
Inspectforlooseormissinghardwareonframeandcrossbraces.
Inspectforbentframeorcrossbraces.
Checkthatthewheellocksdonotinterferewithtireswhenrolling.
Checkthatthewheellockpivotpointsarefreeofwearandlooseness.
Checkthatthewheellocksareeasytoengage. Ensurethatthewheellockspreventthewheelchairfrommovingwhenengaged.
Inspecttheseatandbackforripsandsagging.
Inspecttheseatandbackforlooseorbrokenhardware.
Inspectthebackcanehandgripsforwear/looseness/deterioration.
Inspectseatpositioningstrapforanysignsofwear.Ensurebucklelatches.Verifyhardwarethatattachesstraptoframeissecureandundamaged.Replaceifnecessary.
Inspecttiresforflatspotsandwear.
Checkpneumatictiresforproperinflation.
CAUTIONAs with any vehicle, check the wheels and tires periodically for cracks and wear.Replace if damaged.
Ifequipped,checkthatquickreleaseaxleslockproperly.Lubricateifnecessary.
Checkthatthereisnoexcessivesidemovementorbindingintherearwheelswhenliftedandspun.
Inspectrearwheelsforcracked,bentorbrokenspokes.
Ensureallspokesareuniformlytight.
Inspecthandrimsforsignsofroughedgesorpeeling.
Inspectaxleassemblyforpropertensionbyspinningcaster.Castershouldcometoagradualstop.
Adjustfrontcasters/forksbearingsystemifwheelwobblesnoticeablyorbindstoastop.
7/26/2019 Invacare 9000 Series user Manual
16/88
SECTION 2SAFETY INSPECTION/TROUBLESHOOTING
9000 Series 16 Part No. 1076155
Ensurewheelbearingsarecleanandfreeofmoisture.
Checkheadtubelocknutsfortightness.
Inspectcastersforcracksandwear.
Inspectfrontcastersforcracked,bentorbrokenspokes.
Cleanupholsteryandarmrests.
Checkthatalllabelsarepresentandlegible.Replaceifnecessary.
Troubleshooting
Maintenance
Maintenance Safety Precautions
WARNING
After any adjustments, repair or service and before use, make sure all attachinghardware is tightened securely. Otherwise injury or damage may occur.
CAUTIONDO NOT overtighten hardware attaching to the frame. This could cause damage tothe frame tubing.
Suggested Maintenance Procedures
1. Makesureallnutsandboltsaretight.Checkallpartsfordamageorwearandreplace.Checkallpartsforproperadjustment.
ChairVeersRight/Left
Chair 3Wheels
Sluggish Turn orPerformance
CastersFlutter
SqueaksandRattles
LoosenessinChair
Solutions
X X X X
Check tires forcorrect and equal
pressure
X X X XCheck for loose nuts
and bolts.
X X XCheck caster headtube
angle.
X X
Check that rearwheels are equally
spaced away from seatframe.
7/26/2019 Invacare 9000 Series user Manual
17/88
SECTION 2SAFETY INSPECTION/TROUBLESHOOTING
Part No. 1076155 17 9000 Series
2. 9000SL/9000XTonly Keepquickreleaseaxlesfreeofdirtandlinttoensurepositivelockingandproperoperation.RefertoAdjustingQuickReleaseAxleonpage 57.
3. 9000SL/9000XTonly Oilquickreleaseaxlesatleastonceamonth(3in1oilorequivalent).
WARNINGDO NOT use the wheelchair unless it has the proper tire pressure (p.s.i.). DO NOToverinflate the tires. Failure to follow these suggestions may cause the tire to
explode and cause bodily harm.
4. Iftiresarepneumatic,recommendedtirepressureislistedonthesidewallofthetire.
CAUTIONAs with any vehicle, check the wheels and tires periodically for cracks and wear.Replace if damaged.
5. Therearwheels,castersandtiresshouldbecheckedperiodicallyforcracksandwear,andshouldbereplacedifdamaged.
NOTE:Tirewearisexcessiveif:
PneumaticTires thereismissingtreadorthetiresarebald.
UrethaneTires therearecuts,surfacedefectsorthetiresarelooseontherims.
RubberTires 30%ormoreofthetirehaswornaway.
NOTE:Invacarerecommendsthattiresandcastersbereplacedeveryfive(5)years.
6. Periodicallyadjustwheellocksincorrelationtotirewear.RefertoAdjustingPatientOperatedWheelLocksonpage 83.
7. Periodicallycheckhandrimstoensuretheyaresecuredtotherearwheels.Ifloose,tightenthem.
8. Periodicallycheckcasterwheelbearingstomakesuretheyarecleanandfreefrom
moisture.UseaTeflonlubricantifnecessary.
WARNINGWhen cleaning rear cane or hand grip areas use only a clean towel lightly dampenedwith cool water. Verify that grips are dry prior to use. Use of soap or ammonia
based cleaning solutions will result in the hand grips sliding off the cane assembly.
Failure to observe this warning may result in injury to the user or bystanders.
9. Handgripsshouldbecheckedmonthlyforwear/looseness/deterioration. Cleanifdesired.Replaceifloosenessordeteriorationisfound.
10. Checkupholsteryforsagging,ripsortears.
7/26/2019 Invacare 9000 Series user Manual
18/88
SECTION 3SEAT AND BACK
9000 Series 18 Part No. 1076155
SECTION 3SEAT AND BACK
WARNING
After any adjustments, repair or service and before use, make sure all attachinghardware is tightened securely. Otherwise, injury or damage may occur.
The seat depth, back height/angle, seat angle, size/position of the front casters,size/position of the rear wheels, anti-tipper model, as well as the user conditiondirectly relate to the stability of the wheelchair. Any change to one (1) or any
combination of the ten (10) may cause the wheelchair to decrease in stability. Useextreme caution when using a new seating position.
Adjusting Back Angle
NOTE:Forthisprocedure,refertoFIGURE
3.1.NOTE:Thisprocedureappliesto9000XTand9000SLadjustablebackmodelwheelchairsonly.
NOTE:SpacesaverarmsDONOTworkwiththeadjustableanglebackoption.
1. Loosen,butDONOTremovethepivotscrewandlocknutthatsecuresthebackanglebrackettothewheelchairframe.
2. Removethe
hex
screw,
washers
and
locknutthatsecurethebackanglebrackettothewheelchairframe.
3. Determinethemountingholeinthebackanglebracketforthenecessarybackanglerelativetotheseatframe.
4. Reinstallthebackanglebrackettothewheelchairframewiththeexistinghexscrew,washersandlocknut.Securelytighten.
5. SecurelytightenthepivotscrewandlocknutloosenedinSTEP1.
6. RepeatSTEPS15fortheoppositesideofthewheelchair.
NOTE:Ensurebothbackanglebracketsareadjustedtothesamemountingposition.
FIGURE 3.1 Adjusting Back Angle
Washer
110
10095
9085
Hex
Screw
Back Angle
Bracket
Wheelchair
Frame
Locknut
WasherLocknutPivot Screw
Back Angle
Bracket
Back Angle
Bracket
Back Angle
BracketBack Angle
Bracket
Back Angle
Bracket
Back Angle
Bracket
105
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-7/26/2019 Invacare 9000 Series user Manual
19/88
SECTION 3SEAT AND BACK
Part No. 1076155 19 9000 Series
Adjusting Back Height
9000 SL without Adjustable Back Angle Option
NOTE:Forthisprocedure,refertoFIGURE3.2.
NOTE:Therearetwo(2)heightrangesofbackcaneswiththree(3)heightsettingswithineach
range(15to17inchesor17to19inches)andtwo(2)backupholsteryheightsavailable.
1. Ifchangingbackcanes,removetheexistingbackupholstery.RefertoReplacingtheBackUpholsteryintheOwnersManual,partnumber1056953.Otherwise,proceedtoSTEP2.
2. Flipswingbackarmsupandoutoftheway.RefertoSwingBackArmsintheOwnersManual,partnumber1056953.
3. Removethe
mounting
screw
and
locknutthatsecuretheexistingbackcanetothewheelchairframe.
NOTE:Makeanoteofmountingscrewandlocknutorientationforreinstallation.
4. Removeexistingbackcaneifchangingheightrange.
5. RepeatSTEPS23foroppositesideofwheelchair.
6. Slidethe
new/existing
back
canes
into
thewheelchairframe. FIGURE 3.2 Adjusting Back Height- 9000SL without Adjustable Back Angle Option
7. Lineupmountingholesinthewheelchairframeandthenew/existingbackcanes.
NOTE:Thebackcanescontainathreadedinsert.Makesuremountingholesintheinsertlineupwiththemountingholesinthebackcane(DetailA).
8. Installnew/existingbackcanebyperformingthefollowing:
A. Threadexistingmountingscrewthroughthethreadedinsertofthenew/existingbackcanes.
B. Securelytightenmountingscrewandlocknutthatsecurethenew/existingback
canetothewheelchairframe.
9. Ifchangingbackcanes,securelytightenthenewbackupholsterytothebackcanes.RefertoReplacingtheBackUpholsteryintheOwnersManual,partnumber1056953.Otherwise,proceedtoSTEP9.
10. Fliptheswingbackarmsdownforuse.RefertoSwingBackArmsintheOwnersManual,partnumber1056953.
Height
Settings
Locknut Wheelchair
Frame
Mounting
Screw
Back
Cane
DETAIL A
Threaded
Insert
Mounting
Hole
NOTE:Threadedinsertfitsinsidebackcane.
http://-/?-http://-/?-http://-/?-http://-/?-7/26/2019 Invacare 9000 Series user Manual
20/88
SECTION 3SEAT AND BACK
9000 Series 20 Part No. 1076155
9000 SL with Adjustable Back Angle Option and 9000 XT/XDT
NOTE:Forthisprocedure,refertoFIGURE3.3.
1. Removethetwo(2)mountingscrews,spacersandlocknutsthatsecurethetwo(2)backcanestothewheelchairframe(DetailA).
2. Repositionthebackcanestoone(1)offive(5)heightadjustmentpositions(Detail
B):
NOTE:Holesarenumberedfrombottomtotopforreferenceonly.Therearenonumbersonthebackcanes.
3. Reinstallthetwo(2)mountingscrews,spacersandlocknutsthatsecurethebackcanestothewheelchairframeandsecurelytighten.
NOTE:Thespacersmustbeontheoutsideofthewheelchairinordertoproperlytightenthemountingscrews.
FIGURE 3.3 Adjusting Back Height- 9000 SL with Adjustable Back Angle Option and 9000XT/XDT
Adjusting Seat Width
NOTE:Forthisprocedure,refertoFIGURE3.4.
NOTE:Whenadjustingtheseatwidthofthewheelchair,thebackandseatupholsteryMUSTbechanged.Ifapplicable,theheadrestpillowandheadrestupholsteryMUSTbechangedaswell.
1. Removetheexistingbackandseatupholsteryfromthewheelchair.RefertoReplacingtheBackUpholsteryandReplacingtheSeatUpholsteryintheownersmanual,partnumber1056953.
HOLE NUMBER 1 & 2 2 & 3 3 & 4 4 & 5 5 & 6
BACK HEIGHT 15 in. 16 in. 17 in. 18 in. 19 in.
Height
Adjustment
Positions
654321
Hole
Back Cane
Wheelchair
Frame
Back Cane
Wheelchair
Frame
Mounting Screws
Spacers Locknuts
DETAIL A DETAIL B
7/26/2019 Invacare 9000 Series user Manual
21/88
SECTION 3SEAT AND BACK
Part No. 1076155 21 9000 Series
2. Removethefour(4)buttonscrewsandlocknutsthatsecurethetwo(2)pivotlinkstothewheelchairframeandcrossbraces.
3. Removethetwo(2)buttonscrews,locknutsandcrossbracesaddlethatsecuresthebottomofthecrossbracetothewheelchairframe.Repeatforothercrossbrace.
4. Removethehexscrew,covedwashers,washersandlocknutthatsecurethetwo(2)crossbracestogether.SeeDetail B ofFIGURE3.4.
NOTE:Makenoteoftheorientationofthecovedwashers,washersandlocknutforassemblingthenewcrossbraces.RefertoDetail BofFIGURE3.4.
5. Assemblethetwo(2)newcrossbracestogetherwiththeexistinghexscrew,covedwashers,washersandlocknut.Securelytighten.RefertoDetail B ofFIGURE3.4forhardwareorientation.
6. Determinethecorrectpivotlinkandmountingholetousewiththedesiredseatwidth.Refertothefollowingchart.
*NOTE:16,18,and20incharetheonlycrossbracesettingsavailableonthe9000SL.
7. Securethepivotlinktothecrossbracesandwheelchairframewiththefour(4)buttonscrewsandlocknuts.Securelytighten.
NOTE:Positioncrossbracesaddleonwheelchairframeusingthewasherontheundersideofthewheelchairframeasareference.RefertoDetail A ofFIGURE3.4forproperpositioningofthecrossbracesaddle.
8. Reinstallthetwo(2)buttonscrews,locknutsandcrossbracesaddlethatsecurethebottomofthenewcrossbracetothewheelchairframe.RefertoDetail B ofFIGURE3.4forhardwareorientation.Repeatforoppositecrossbrace.Securelytighten.
9. Installthenewbackandseatupholsteryontothewheelchair.RefertoReplacingBackUpholsteryandReplacingSeatUpholsteryintheownersmanual,partnumber1056953.
SEAT WIDTH PIVOT LINK
14-INCH15-INCH
*16-INCH*18-INCH
*20-INCH
22-INCH
14-Inch 15-Inch
16-Inch
x
18-Inch
DO NOT use
20-Inch
22-Inch
7/26/2019 Invacare 9000 Series user Manual
22/88
SECTION 3SEAT AND BACK
9000 Series 22 Part No. 1076155
FIGURE 3.4 Adjusting Seat Width
Wheelchair
Frame Button Screw
(STEPS 2,7)
Crossbrace
(STEPS 4,5)
Pivot Link
(STEPS 2,7)Locknut
(STEPS 2,7)
Button Screw
(STEPS 2,7)Locknut
(STEPS 2,7)
Crossbrace
Saddle
(STEPS 3,8)
Button Screw
(STEPS 3,8)
Locknut
(STEPS 3,8)Button Screw
(STEPS 2,7)Locknut
(STEPS 2,7)
Crossbrace
Saddle
(STEPS 3,8)
Coved
Washers
Washer
Coved
Washers
Washer
Locknut
Washer
Hex Screw
Coved
Washer
CrossbracesWheelchair
Frame
Washer
Crossbrace
Saddle
DETAIL A
DETAIL B (STEPS 4 AND 5)
7/26/2019 Invacare 9000 Series user Manual
23/88
SECTION 3SEAT AND BACK
Part No. 1076155 23 9000 Series
Adjusting Seat Depth
WARNINGThe seat depth, back height/angle, seat angle, size/position of the front casters,size/position of the rear wheels, anti-tipper model, as well as the user condition
directly relate to the stability of the wheelchair. Any change to one (1) or any com-
bination of the ten (10) may cause the wheelchair to decrease in stability. Useextreme caution when using a new seating position.
9000XT Model
NOTE:Forthisprocedure,refertoFIGURE3.5.
1. Removetheexistingseatupholsteryfromthecrossbraces.RefertoReplacingSeatUpholsteryinthe
OwnersManual,partnumber1056953.
NOTE:Whenadjustingtheseatdepthofthewheelchair,theseatupholsteryMUSTalsobechanged.
2. Removethetwo(2)plugbuttonsfromtheendsofthecrossbracesthataretowardthefrontofthewheelchair.
NOTE:Theplugbuttonsareusedintheendsoftheseatextensionspacers.
3. Installthetwo(2)seatextensiontubesintotheendsonthecrossbraces.
FIGURE 3.5 Adjusting Seat Depth-
9000XT Model
4. Performone(1)ofthefollowing:
1inchSeatExtension Alignthefrontmostmountingholeoftheseatextensiontubewiththefrontmostmountingholeinthecrossbrace.
2inchSeatExtension Alignthemiddlemountingholeoftheseatextensiontubewiththefrontmostmountingholeinthecrossbrace.
5. RepeatSTEP4fortheoppositeseatextensiontube.
6. Installthe
two
(2)
seat
extension
spacers
onto
the
two
(2)
seat
extension
tubes.
7. Securethenewseatupholsterytothecrossbraces.RefertoReplacingSeatUpholsteryintheOwnersManual,partnumber1056953.
NOTE:Makesuretolineupthemountingholesintheseatextensiontubesandtheseatextensionspacerswiththenewseatupholstery.
8. Installplugbuttonsintotheendsoftheseatextensionspacers.
Mounting
Screws
Seat
ExtensionSpacer
Washer Seat
Upholstery
Crossbrace
Hole for 1-inch
Seat Extension
Seat
Extension
TubePlug Button
Hole for 2-inch
Seat Extension
Front of
Seat
Rear of
Seat
7/26/2019 Invacare 9000 Series user Manual
24/88
SECTION 3SEAT AND BACK
9000 Series 24 Part No. 1076155
9000 XDT and 9000 SL
NOTE:Forthisprocedure,refertoFIGURE3.6.
NOTE:9000XDTwheelchairshavetwo(2)framedepthranges:16to18inchesand19to20inches.A1618inchframedepth
wheelchaircannotbeadjustedtoa19to20inchrangeandviceversa.
1. Removetheexistingseatupholsteryfromthewheelchair.RefertoReplacingtheSeatUpholsteryintheOwnersManual,partnumber1056953.
NOTE:Whenadjustingtheseatdepthofthewheelchair,theseatupholsteryMUSTalsobechanged.
2. Removethe
two
(2)
plug
buttons
from
theendsofthecrossbracesthataretowardsthefrontofthewheelchair.
NOTE:Thetwo(2)plugbuttonsareusedintheendsoftheseatextensiontubes.
3. Installthetwo(2)seatextensiontubesintotheendsonthecrossbraces.
4. Performone(1)ofthefollowing:
9000XDT Alignthesecond
mountingholefromtherearoftheseatextensiontubewiththefrontmostmountingholeinthecrossbrace.
NOTE:DONOTusebackmountinghole.Ifbackmountingholeisused,themountingholefortheothermountingscrewwillnotlineupproperly.
FIGURE 3.6 Adjusting Seat Depth- 9000XDT and 9000 SL
9000SL Aligntherearmountingholeoftheseatextensiontubewiththesecondmountingholefromthefrontofthecrossbrace.Slidespacertubeoverseat
extensiontube.
NOTE:Therearmountingholeisfurtherfromitsendoftheseatextensiontubethanthefrontmountingholeisfromitsend.
NOTE:Theendofthespacertubethatisclosertothespacertubemountingholeshouldfacetothefront.
5. RepeatSTEP4fortheoppositeseatextensiontube.
Spacer
Tube
Mounting Screws
9000 XDT
Seat Upholstery
Washer
Seat
Extension
Tube
Plug Button
Second
Mounting
Hole
DO NOT use
this back
mounting hole
Crossbrace
9000 SL
Seat Extension
Tube
Mounting Screws
Seat Upholstery
Second
Mounting
Hole
Crossbrace
Rear
Mounting
Hole
Plug Button
Front ofSeat
Rear of
Seat
Rear of
Seat
Front of
Seat
Spacer Tube
Mounting Hole
7/26/2019 Invacare 9000 Series user Manual
25/88
SECTION 3SEAT AND BACK
Part No. 1076155 25 9000 Series
6. Installthenewseatupholsteryontothewheelchair.Makesuretolineupthemountingholesintheseatextensiontubeswiththenewseatupholstery.RefertoReplacingSeatUpholsteryintheOwnersManual,partnumber1056953.
7. Installplugbuttonsintotheendsoftheseatextensiontubes.
7/26/2019 Invacare 9000 Series user Manual
26/88
SECTION 4FRONT CASTERS
9000 Series 26 Part No. 1076155
SECTION 4FRONT CASTERS
WARNINGAfter any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely. Otherwise, injury or damage may occur.
Front Caster Mounting Adjustments
NOTE:Forthisprocedure,refertoFIGURE4.1.
1. Removethehexscrew,washers(ifsoequipped)andlocknutthatsecurethefrontcastertothefork.
2. Repositionthefrontcasterontheforktothedeterminedmountinghole.RefertoChangingSeattoFloorHeight/SeattoFloorAngleonpage 29todeterminefrontcastermountingholeforfrontcastersizeandseattofloorheight.
3. Securefrontcastertoforkwithexistinghexscrewandlocknut.Securelytighten.
WARNINGMake sure both front casters are positioned in the same mounting hole before usingthe wheelchair. Otherwise, injury may result.
4. RepeatSTEPS13fortheoppositefrontcaster.
FIGURE 4.1 Front Caster Mounting Adjustments
Fork
Front
Caster
Washer
Locknut
Washer
Hex Screw
7/26/2019 Invacare 9000 Series user Manual
27/88
SECTION 4FRONT CASTERS
Part No. 1076155 27 9000 Series
Converting from Trailing to Leading or Leading to
Trailing Casters
NOTE:Forthisprocedure,refertoFIGURE4.2.
Adjustingthecasterheadtubeposition(leadingortrailing)changesthewheelbase
lengthofthewheelchair.Therearetwo(2)adjustmentswhichallowfora:
Longerwheelbase Thecasterheadtubeisleadingorinfrontofthewheelchairframe.
Shorterwheelbase Thecasterheadtubeistrailingorbehindthewheelchairframe.
NOTE:Ifthecasterheadtubesarepositionedin
theleading
position
when
using
8inch
casters,
a60footrestisrecommendedtoallowadequateroomforfeetandcasterswivel.
NOTE:Makenoteoftheorientationofthecamforproperreinstallation.Ifchangingtheseattofloorheightand/ortheseattofloorangle,refertoChangingSeattoFloorHeight/SeattoFloorAngleonpage 29.
1. Removethetwo(2)mountingscrews,covedspacer,washer,camandtwo(2)
locknutsthatsecuretheinsertandthecasterheadtubetothewheelchairframe.
NOTE:Theinsertwilldropifitisnotcaught.
2. RepeatSTEP1foroppositeside.
3. Positiontheexistingrightcasterheadtubeontotheleftwheelchairframe.
NOTE:Ensuretheinsertispositionedintothe
bottomofthewheelchairframewiththemountingholesalignedwiththeframemountingholes.
4. Ensurecovedspacerisproperlypositionedwiththeroundedendup.Thecutout(DetailA)ontheundersideofthecovedspacershouldcleartheframejoint.
FIGURE 4.2 Converting from Trailing toLeading or Leading to Trailing Casters
Washer
Cam
Locknuts
Coved
Spacer
Caster
Headtube
Insert
MountingScrews
Wheelchair Frame
Leading
Trailing
Wheelchair
Frame
Frame Joint
Coved Spacer
Cam
Locknuts
Washer
Caster Headtube
Insert
Mounting
Screws
DETAIL A - COVED SPACER
Rounded
EndCut-out onUnderside of
Coved Spacer
Frame
Mounting
Holes
Frame
Mounting
Holes
7/26/2019 Invacare 9000 Series user Manual
28/88
SECTION 4FRONT CASTERS
9000 Series 28 Part No. 1076155
5. Looselytightenthebottomoftheexistingcasterheadtubetothewheelchairframeusingexistinghardware.
6. Adjusttheseattofloorangle.RefertoChangingSeattoFloorHeight/SeattoFloorAngleonpage 29.
7. Securethecamtothetopofthecasterheadtubewiththeexistinghardware.
8. Securelytighten
the
caster
headtube
to
the
wheelchair
frame.
Torque
locknuts
to
120140inchlbs.
9. Adjusttheantitippers.RefertoInstalling/AdjustingAntitippersonpage 80.
Repositioning/Replacing Cam
NOTE:Forthisprocedure,refertoFIGURE4.2.
1. Doone(1)ofthefollowing:
ToReposition RefertoChangingSeattoFloorHeight/SeattoFloorAngleon
page 29. ToReplace Beforeremovingthecam,makenoteofthepositionofthecaminthe
casterheadtubeforproperreinstallation.Thenremove.
2. Loosenthebottommountingscrewandlocknutthatsecuresthecasterheadtubetothewheelchairframe.
NOTE:Looseningthebottommountingscrewallowsthecamtobepositionedeasilyinthecasterheadtube.
3. Removethetoplocknutandcamfromthecasterheadtube.
4. Installthenew/existingcamatthepositionobservedinSTEP1.
5. Tightenbothlocknutstosecurethecasterheadtubetothewheelchairframe.Torqueto120140inchlbs.
7/26/2019 Invacare 9000 Series user Manual
29/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 29 9000 Series
SECTION 5SEAT TO FLOOR
WARNINGAfter any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely. Otherwise, injury or damage may occur.
Changing Seat-to-Floor Height/Seat-to-Floor Angle
WARNING
Before performing this procedure, refer to Stability - All Models on page 12foradditional requirements.
DO NOT deviate from the charts on the following pages. If the restrictions forseat-to-floor heights and seat-to-floor angles are not followed, the wheelchair will be
in an unsafe position. Before changing these settings, refer to the following chartsfor the allowable positions.
NOTE:Forthisprocedure,refertoFIGURE 5.1.
NOTE:Thissectionisfornonreclinerwheelchairsonly.Forrecliners,refertoChangingSeattoFloorHeightonpage 77.
NOTE:Seattofloorangleadjustmentsareonlyavailableon9000XTwiththeoffsetaxleoptionandadjustablecasterjournal(ADJC).Allothermodels/optionshavea3seattofloorangle.
ThedifferentSeattoFloorheightsandangles(DetailA)arepossiblebyusingdifferentcombinationsofrearwheels,rearwheelpositions,frontcasterpositions,frontcastersizeandcampositions.
1. Determinethemodelandframestyleofyourwheelchair.RefertothefollowingchartandFIGURE 5.1.
MODEL FRAME STYLE
Adult/Hemi Adult/Tall Super Low
9000 SL X N/A N/A
9000 XT X N/A X
9000 XT with Bolt-on-Headtube (ADJC) X N/A N/A
9000 XDT N/A X N/A
7/26/2019 Invacare 9000 Series user Manual
30/88
SECTION 5SEAT TO FLOOR
9000 Series 30 Part No. 1076155
FIGURE 5.1 Changing Seat-to-Floor Height/Seat-to-Floor Angle
2. Refertothefollowingchartsofrearwheelsizesandfrontcastersizestodeterminemountingadjustmentsforobtainableseattofloorheights/anglesfortheappropriateframestyle.
SuperLowFrameStyleonpage 31
Adult/TallFrameStyleonpage 31
Adult/HemiFrame
Styles
on
page 32
ChangingSeattoFloorHeightonpage 77forreclinerframestyles
NOTE:Ifusingamputeebrackets,thefollowingrestrictionsapply:
Angle a3seattofloorangleistheonlyavailableangle.
RearWheelMountingPosition RefertothechartsintheOwnersManual,partnumber1056953,fortheproperrearwheelmountingposition.
3. Removetherearwheels.RefertoRemoving/Installing RearWheelsonpage 52.
4. Ifnecessary,adjustthecasterheadtubepositionand/orthecamposition.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27and/or
Repositioning/Replacing Camonpage 28.
5. Ifnecessary,replacetheforks.RefertoInstalling/Replacing SixorEightInchFrontCastersandForksintheOwnersManual,partnumber1056953.
6. Ifnecessary,adjustthefrontcasterpositioninthefork.RefertoFrontCasterMountingAdjustmentsonpage 26.
7. Reinstalltherearwheelsontothewheelchair.RefertoRemoving/InstallingRearWheelsonpage 52.
Seat-to-Floor
Height
Seat-to-Floor
Angle
Adult/Hemi Adult/Tall Super Low Recliner
DETAIL A
7/26/2019 Invacare 9000 Series user Manual
31/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 31 9000 Series
8. Adjustthewheellocks.RefertoUsing/AdjustingthePatientOperatedWheelLocksintheOwnersManual,partnumber1056953.
WARNINGAfter changing seat-to-floor height and/or seat-to-floor angle, the anti-tippersMUST be replaced or adjusted before using the wheelchair. Refer to
Installing/Adjusting Anti-tippers on page 80.
Super Low Frame Style
NOTE:Forthisinformation,refertothefollowingtableandtoFIGURE 5.2.
FIGURE 5.2 Super Low Frame Style
Adult/Tall Frame Style
NOTE:Forthisinformation,refertothefollowingtableandtoFIGURE 5.3.
6-inch Front Casters, 3 Seat Angle
SEAT-TO-FLOORHEIGHT(INCHES)
FRONTCASTER
MOUNTINGPOSITION
REAR WHEEL SIZE ANTI-TIPPER PARTNUMBER
1314
TopMiddle
20-inch22-inch
10645201064520
8-inch Front Casters, 3 Seat Angle
SEAT-TO-FLOORHEIGHT
(INCHES)
FRONT CASTERMOUNTING
POSITION
REARWHEEL
SIZE
REAR WHEELMOUNTING
POSITION
ANTI-TIPPERPART
NUMBER17191921
TopTop w/ 2-inch extension
BottomBottom w/ 2-inch extension
24-inch24-inch24-inch24-inch
TopMiddleMiddleBottom
1058752105875210587521058836
Bottom (Not used with
Super Low frame style)
Rear Wheel
Mounting Positions
6-Inch Fork
Mounting Positions
Top
Middle
7/26/2019 Invacare 9000 Series user Manual
32/88
SECTION 5SEAT TO FLOOR
9000 Series 32 Part No. 1076155
FIGURE 5.3 Adult/Tall Frame Style
Adult/Hemi Frame Styles
Refertothechartsonthefollowingpagesforobtainableseattofloorheightsandseattoflooranglesforwheelchairswiththeadult/hemiframestyle.
24-Inch Rear Wheels and 8-Inch Front Casters
WARNING
If changing the seat-to-floor angle to 6, anti-tippers MUST be installed.
Refertothefollowingtabletodeterminetheobtainableseattofloorheightsandseattoflooranglesfor24inchrearwheelsand8inchfrontcasters:
*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.
SEAT-TO-FLOORHEIGHT*
SEAT-TO-FLOORANGLE
REFER TO
19 inches 3 Chart 1
19 inches 6 Chart 2
18 inches 0 Chart 3
18 inches 3 Chart 4
18 inches 6 Chart 5
17 inches 0 Chart 6
17 inches 3 Chart 7
17 inches 6 Chart 8
Rear Wheel
Mounting Positions
8-Inch Fork
Mounting Positions
Without 2-Inch
Extension
With 2-Inch
ExtensionTop
TopTop
Middle
Bottom
Middle (Not used
with Adult/Tall
frame style)
Bottom Bottom
Middle (Not used
with Adult/Tall
frame style)
7/26/2019 Invacare 9000 Series user Manual
33/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 33 9000 Series
NOTE:Charts1to8applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner
framestyles.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovide
adequatetire
clearance
between
the
rear
tire
and
the
front
caster.
Refer
to
Converting
from
Trailing
toLeadingorLeadingtoTrailingCastersonpage 27.
Chart 1 - Seat-to-Floor Height of 19 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIP
PART/MODELNUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
1360 On-Chair
1058836Off-Chair
Chart 2 - Seat-to-Floor Height of 19 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
N/A On-Chair
1113766Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
Hole 4
Hole 2
Hole 4
Hole 2
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
34/88
SECTION 5SEAT TO FLOOR
9000 Series 34 Part No. 1076155
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailing
toLeadingorLeadingtoTrailingCastersonpage 27.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
Chart 3 - Seat-to-Floor Height of 18 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A On-Chair
1058836 Off-Chair
Chart 4 - Seat-to-Floor Height of 18 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
1360 On-Chair
1058836 Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
35/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 35 9000 Series
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
Chart 5 - Seat-to-Floor Height of 18 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A On-Chair
1113766Off-Chair
Chart 6 - Seat-to-Floor Height of 17 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
N/A On-Chair
1058836 Off-Chair
Hole 4
Hole 3
Hole 4
Hole 3Notch
Front
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
36/88
SECTION 5SEAT TO FLOOR
9000 Series 36 Part No. 1076155
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
Chart 7 - Seat-to-Floor Height of 17 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
1360 On-Chair
1058836Off-Chair
Chart 8 - Seat-to-Floor Height of 17 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
N/A On-Chair
1113766Off-Chair
Hole 4
Hole 3
Hole 4
Hole 3
Front
Notch
Hole 4
Hole 5
Hole 4
Hole 5
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
37/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 37 9000 Series
24-Inch Rear Wheels and 6-Inch Front Casters
WARNINGIf changing the seat-to-floor angle to 6, anti-tippers MUST be installed.
Refertothefollowingtabletodeterminetheobtainableseattofloorheightsand
seatto
floor
angles
for
24
inch
rear
wheels
and
6inch
front
casters:
*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.
NOTE:Charts9to14applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner
framestyles.
SEAT-TO-FLOORHEIGHT*
SEAT-TO-FLOORANGLE
REFER TO
17 inches 0 Chart 9
17 inches 3 Chart 10
17 inches 6 Chart 11
16 inches 0 Chart 12
16 inches 3 Chart 13
15 inches 0 Chart 14
Chart 9 - Seat-to-Floor Height of 17 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIP
PART/MODELNUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058836Off-Chair
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
38/88
SECTION 5SEAT TO FLOOR
9000 Series 38 Part No. 1076155
Chart 10 - Seat-to-Floor Height of 17 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1058752Off-Chair
Chart 11 - Seat-to-Floor Height of 17 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1113765Off-Chair
Chart 12 - Seat-to-Floor Height of 16 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1058836Off-Chair
Hole 4
Hole 3
Hole 4
Hole 3
Front
Notch
Hole 4
Hole 5
Hole 4
Hole 5
Notch
Front
Hole 4
Hole 3
Hole 4
Hole 3
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
39/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 39 9000 Series
22-Inch Rear Wheels and 8-Inch Front Casters
WARNINGIf changing the seat-to-floor angle to 6, anti-tippers MUST be installed.
Chart 13 - Seat-to-Floor Height of 16 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058752Off-Chair
Chart 14 - Seat-to-Floor Height of 15 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058752 Off-Chair
Hole 4
Hole 5
Hole 4
Hole 5
Front
Notch
Hole 4
Hole 5
Hole 4
Hole 5
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
40/88
SECTION 5SEAT TO FLOOR
9000 Series 40 Part No. 1076155
Refertothefollowingtabletodeterminetheobtainableseattofloorheightsandseattoflooranglesfor22inchrearwheelsand8inchfrontcasters:
*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.
NOTE:Charts15to20applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner
framestyles.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
SEAT-TO-FLOORHEIGHT*
SEAT-TO-FLOORANGLE
REFER TO
19 inches 6 Chart 15
18 inches 3 Chart 16
18 inches 6 Chart 17
17 inches 0 Chart 18
17 inches 3 Chart 19
17 inches 6 Chart 20
Chart 15 - Seat-to-Floor Height of 19 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A On-Chair
1113766 Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
41/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 41 9000 Series
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailing
toLeadingorLeadingtoTrailingCastersonpage 27.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
Chart 16 - Seat-to-Floor Height of 18 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
1360 On-Chair
1058836 Off-Chair
Chart 17 - Seat-to-Floor Height of 18 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
N/A On-Chair
1113766
Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
Hole 4
Hole 2
Hole 4
Hole 2
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
42/88
SECTION 5SEAT TO FLOOR
9000 Series 42 Part No. 1076155
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailing
toLeadingorLeadingtoTrailingCastersonpage 27.
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovideadequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
Chart 18 - Seat-to-Floor Height of 17 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
N/A On-Chair
1058836 Off-Chair
Chart 19 - Seat-to-Floor Height of 17 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A for thisframe style
N/A On-Chair
1058836
Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
43/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 43 9000 Series
*NOTE:Thisoffsetaxleplatepositionrequiresthecasterheadtubetobeleadingtoprovide
adequatetireclearancebetweenthereartireandthefrontcaster.RefertoConvertingfromTrailingtoLeadingorLeadingtoTrailingCastersonpage 27.
22-Inch Rear Wheels and 6-Inch Front Casters
WARNINGIf changing the seat-to-floor angle to 6, anti-tippers MUST be installed.
Refertothefollowingtabletodeterminetheobtainableseattofloorheightsandseattoflooranglesfor22inchrearwheelsand6inchfrontcasters:
*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.
NOTE:Charts21to28applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner
framestyles.
Chart 20 - Seat-to-Floor Height of 17 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD* REARWARD
N/A On-Chair
1113766Off-Chair
SEAT-TO-FLOORHEIGHT*
SEAT-TO-FLOORANGLE
REFER TO
17 inches 0 Chart 21
17 inches 3 Chart 22
17 inches 6 Chart 23
16 inches 0 Chart 24
16 inches 3 Chart 25
16 inches 6 Chart 26
15 inches 0 Chart 27
15 inches 3 Chart 28
Hole 4
Hole 3
Hole 4
Hole 3Notch
Front
7/26/2019 Invacare 9000 Series user Manual
44/88
SECTION 5SEAT TO FLOOR
9000 Series 44 Part No. 1076155
Chart 21 - Seat-to-Floor Height of 17 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1058836 Off-Chair
Chart 22 - Seat-to-Floor Height of 17 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058752Off-Chair
Chart 23 - Seat-to-Floor Height of 17 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1113765Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
Hole 4
Hole 3
Hole 4
Hole 3Notch
Front
7/26/2019 Invacare 9000 Series user Manual
45/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 45 9000 Series
Chart 24 - Seat-to-Floor Height of 16 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058836Off-Chair
Chart 25 - Seat-to-Floor Height of 16 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
1360A On-Chair
1058752Off-Chair
Chart 26 - Seat-to-Floor Height of 16 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1113765Off-Chair
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
Hole 4
Hole 3
Hole 4
Hole 3
Front
Notch
Hole 4
Hole 5
Hole 4
Hole 5
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
46/88
SECTION 5SEAT TO FLOOR
9000 Series 46 Part No. 1076155
20-Inch Rear Wheels and 8-Inch Front Casters
WARNINGIf changing the seat-to-floor angle to 6, anti-tippers MUST be installed.
Refertothefollowingtabletodeterminetheobtainableseattofloorheightsand
seattoflooranglesfor20inchrearwheelsand8inchfrontcasters:
Chart 27 - Seat-to-Floor Height of 17 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1058752Off-Chair
Chart 28 - Seat-to-Floor Height of 15 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1058752Off-Chair
SEAT-TO-FLOORHEIGHT*
SEAT-TO-FLOORANGLE
REFER TO
18 inches 6 Chart 29
17 inches 3 Chart 30
17 inches 6 Chart 31
Hole 4
Hole 3
Hole 4
Hole 3
Front
Notch
Hole 4
Hole 5
Hole 4
Hole 5
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
47/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 47 9000 Series
*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.Theseheightscanvary+/ inchduetotirewearandmanufacturingtolerances.
NOTE:Charts29to31applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner
framestyles.
Chart 29 - Seat-to-Floor Height of 18 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1113766 Off-Chair
Chart 30 - Seat-to-Floor Height of 17 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
1360 On-Chair
1058836 Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Notch
Front
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
48/88
SECTION 5SEAT TO FLOOR
9000 Series 48 Part No. 1076155
20-Inch Rear Wheels and 6-Inch Front Casters
WARNINGIf changing the seat-to-floor angle to 6, anti-tippers MUST be installed.
Refertothefollowingtabletodeterminetheobtainableseattofloorheightsandseattoflooranglesfor20inchrearwheelsand6inchfrontcasters:
*NOTE:Theseattofloorheightsarebasedonurethanetires.Ifwheelchairisequippedwithpneumatic(properlyinflated)orsolidrubbertires,addinchtothemeasurementslistedabove.
Theseheights
can
vary
+/
inch
due
to
tire
wear
and
manufacturing
tolerances.
NOTE:Charts32to39applytoadult/hemiframestylesonly.Refertothechartsforseattofloorheightsettingsforadult/tall(Adult/TallFrameStyleonpage 31)andsuperlowframestyles(SuperLowFrameStyleonpage 31)andChangingSeattoFloorHeightonpage 77forrecliner
framestyles.
Chart 31 - Seat-to-Floor Height of 17 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1113766Off-Chair
SEAT-TO-FLOORHEIGHT*
SEAT-TO-FLOORANGLE
REFER TO
17 inches 3 Chart 32
17 inches 6 Chart 3316 inches 0 Chart 34
16 inches 3 Chart 35
16 inches 6 Chart 36
15 inches 0 Chart 37
15 inches 3 Chart 38
15 inches 6 Chart 39
Hole 4
Hole 2
Hole 4
Hole 2
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
49/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 49 9000 Series
Chart 32 - Seat-to-Floor Height of 17 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
1360A On-Chair
1058752 Off-Chair
Chart 33 - Seat-to-Floor Height of 17 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1113765Off-Chair
Chart 34 - Seat-to-Floor Height of 16 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1058836 Off-Chair
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
Hole 4
Hole 2
Hole 4
Hole 2
Notch
Front
Hole 1
Hole 3
Hole 1
Hole 3
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
50/88
SECTION 5SEAT TO FLOOR
9000 Series 50 Part No. 1076155
Chart 35 - Seat-to-Floor Height of 16 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058752Off-Chair
Chart 36 - Seat-to-Floor Height of 16 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A On-Chair
1113765Off-Chair
Chart 37 - Seat-to-Floor Height of 15 inches and 0 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1058752Off-Chair
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
Hole 4
Hole 3
Hole 4
Hole 3Notch
Front
Hole 4
Hole 2
Hole 4
Hole 2
Front
Notch
7/26/2019 Invacare 9000 Series user Manual
51/88
SECTION 5SEAT TO FLOOR
Part No. 1076155 51 9000 Series
Chart 38 - Seat-to-Floor Height of 15 inches and 3 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
1360A On-Chair
1058752Off-Chair
Chart 39 - Seat-to-Floor Height of 15 inches and 6 Angle
REAR WHEEL POSITION ANTI-TIPPART/MODEL
NUMBERS
FRONT CASTER
OFFSET AXLE OPTION STANDARD MOUNTINGPOSITION
ADJC CAMPOSITIONFORWARD REARWARD
N/A for thisframe style
N/A On-Chair
1113764Off-Chair
Hole 4
Hole 3
Hole 4
Hole 3
Front
Notch
Hole 4
Hole 5
Hole 4
Hole 5
Notch
Front
7/26/2019 Invacare 9000 Series user Manual
52/88
SECTION 6REAR WHEELS
9000 Series 52 Part No. 1076155
SECTION 6REAR WHEELS
WARNINGAfter any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely. Otherwise, injury or damage may occur.
NOTE:Exceptwherenoted,theproceduresinthissectionapplytononreclinermodelsonly.Forreclinermodels,refertoReclineronpage 58.
Removing/Installing Rear Wheels
Quick-Release Axles
WARNING
NEVER use quick-release axles on the 9000 XT (models with offset axle optiononly), 9000XDT or 9000XT recliner wheelchairs.
NOTE:Forthisprocedure,refertoFIGURE 6.1.
NOTE:Ifreplacingthesamesizerearwheel,notethemountingpositiononthewheelchairframeforproperreinstallationofthenewrearwheel.
1. Pushinthedetentpinofthequickreleaseaxle(withwheel)andpulltheaxleoutthroughtheopeninginthecenteroftherearwheelandaxlespacer.
NOTE:Axlespacerisusedonlyifwheelchairisequippedwithconventionalarms.
2. Pushinthedetentpinofthequickreleaseaxleagainandpulltheaxleoutoftherearwheel.
3. RepeatSTEPS12fortheoppositerearwheel.
4. Toreinstalltherearwheelontothewheelchair,reverseSTEPS13.
NOTE:Makesureaxlespacerisbetweenrearwheelandwheelchairframeifwheelchairisequippedwithconventionalarms.
WARNING
Make sure the detent pin and detent balls of the quick-release axle are fully released
before operating the wheelchair.
The detent balls MUST be protruding past the inside of the rear wheel axle bushingfor a positive lock (Detail "A").
Keep detent balls clean.
Invacare recommends inserting quick-release axles with the detent pin to the insideof the wheelchair to prevent accidental release during contact activities.
http://-/?-http://-/?-7/26/2019 Invacare 9000 Series user Manual
53/88
SECTION 6REAR WHEELS
Part No. 1076155 53 9000 Series
5. Ifthedetentballsarenotprotrudingpasttheinsideoftheaxlebushingorthereistoomuchsidetosidemovementoftherearwheelassembly,refertotheOwnersManual(partnumber1056953)forinstructionsonadjustingthequickreleaseaxle.
FIGURE 6.1 Removing/Installing Rear Wheels- Quick-Release Axles
Permanent Axles
Models without Offset Axle Option
NOTE:Forthisprocedure,refertoFIGURE 6.2.
NOTE:Ifreplacingthesamesizerearwheel,notethemountingpositiononthewheelchairframeforproperreinstallationofthenewrearwheel.
1. Removethehubcap(ifapplicable),mountingscrewandlocknutthatsecuretherear
wheeland
axle
spacer
(if
applicable)
to
the
wheelchair.
NOTE:Axlespacerisusedonlyifwheelchairisequippedwithconventionalarms.
2. Toreinstalltherearwheelontothewheelchair,reverseSTEP1.
3. Torquelocknutto4045ftlbs.
4. RepeatSTEPS13fortheoppositewheel.
Quick-Release Axle
Detent Pin
Detent Balls
Axle Bushing
DETAIL A - DETENT BALLS AND DETENT PIN
Inside of
Wheelchair
Outside of
Wheelchair
Quick-Release Axle
Rear Wheel
Axle Spacer (Conventional Arms Only)
Axle Mounting PositionsWheelchair Frame
7/26/2019 Invacare 9000 Series user Manual
54/88
SECTION 6REAR WHEELS
9000 Series 54 Part No. 1076155
FIGURE 6.2 Removing/Installing Rear Wheels- Permanent Axles- Models without OffsetAxle Option
NOTE:Makesureaxlespacerisbetweenrearwheelandwheelchairframeifwheelchairisequippedwithconventionalarms.
Models with Offset Axle Option
NOTE:Forthisprocedure,refertoFIGURE 6.3.
NOTE:Ifreplacingthesamesizerearwheel,notethemountingpositiononthewheelchairframeandintheoffsetaxleplatesforproperreinstallationofthenewrearwheel.
1. Removehubcap.
2. Removethelocknutsecuringthepermanentaxletotheoffsetaxleplates.
3. Removethepermanentaxle,hubcapwasher,two(2)spacersandrearwheelfromthewheelchair.
4. Performone(1)ofthefollowing:
InstallationInSamePosition ProceedtoSTEP5.
InstallationInDifferentPosition Performthefollowingsteps:
i. RefertothechartsinSeattoFlooronpage 29todeterminethepropermountingpositionforthedesiredseattofloorheightoranglechange.
NOTE:Theoffsetaxleplatesarenumbered(DetailA)onone(1)sideonly.Axleplatesmayneedpositioningwiththenumberedsidetotheinsideofthewheelchair.
NOTE:Theoffsetaxleplatesmaybemountedin