INSTRUCTIONS W34 WALL PACK INSTALLATION RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNINGS: • Make certain power is OFF before installing or maintaining fixture. NOTE: • No user maintenance or cleaning required. CAUTION: • For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened firmly. Apply weatherproof silicone sealant around the edge of the wall box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries. Fixture should not be recessed. Mount fixture on a wall with lens facing down as shown below. Use the Drill Template on the inside back surface of the housing to match most standard junction boxes or utilize Lag Bolt Locations (4) indicated on Fig. 1 to mount 1. Open door by loosening (2) screws. Remove Reflector by loosening (2) screws. Reflector will hang by secured tether during installation as shown in Fig. 2. 2. Prepare the Housing for use by drilling out the appropriate holes. 3. Line up the Housing in desired location and mount securely. 4. Complete the wiring to the supply wires and ground (see wiring instructions). 5. Install the Reflector back into its original position as shown on Fig. 3 (shown on next page). MOUNTING FIXTURE TO THE WALL W34-30L/35L W34-55L/70L/90L W34-150L FIG. 1 FIG. 2 Drill Template Lag Bolt Locations Housing Reflector
3
Embed
INSTRUCTIONS W34 WALL PACK INSTALLATION · W34 WALL PACK INSTALLATION RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
INSTRUCTIONSW34 WALL PACK INSTALLATION
RAB Lighting is committed to creating high-quality, aff ordable, well-designed and energy-effi cient LED lighting and controls that make it easy for electricians to installand end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
IMPORTANTREAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.RAB fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.WARNINGS: • Make certain power is OFF before installing or maintaining fi xture.NOTE:• No user maintenance or cleaning required.CAUTION: • For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened fi rmly. Apply
weatherproof silicone sealant around the edge of the wall box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.
Fixture should not be recessed. Mount fi xture on a wall with lens facing down as shown below. Use the Drill Template on the inside back surface of the housing to match most standard junction boxes or utilize Lag Bolt Locations (4) indicated on Fig. 1 to mount
1. Open door by loosening (2) screws. Remove Refl ector by loosening (2) screws. Refl ector will hang by secured tether during installation as shown in Fig. 2.
2. Prepare the Housing for use by drilling out the appropriate holes.
3. Line up the Housing in desired location and mount securely.
4. Complete the wiring to the supply wires and ground (see wiring instructions).
5. Install the Refl ector back into its original position as shown on Fig. 3 (shown on next page).
MOUNTING FIXTURE TO THE WALL
W34-30L/35L W34-55L/70L/90L W34-150L
FIG. 1
FIG. 2
Drill Template
Lag Bolt Locations
Housing
Reflector
INSTRUCTIONS W34 WALL PACK INSTALLATION
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
TROUBLESHOOTING
CLEANING & MAINTENANCE
1. Check that the line voltage at the fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.
3. Is the photocell, if used, functioning properly?
4. Check if the fuse has blown out.
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
1. Clean glass lens with non-abrasive, glass cleaning solution.
2. Do not open fixture to clean the LED. Do not touch the LED.
3. No user maintenance or cleaning required.
0-10V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. For 0-10V Dimming, follow the wiring directions as shown (Fig. 4).
1. Connect the black fixture lead to the LINE supply lead.
2. Connect the white fixture lead to the COMMON supply lead.
3. Connect the GROUND wire from fixture to supply ground.
4. Connect the purple fixture lead to the (V+) DIM lead.
5. Connect the gray fixture lead to the (V-) DIM lead.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
FIG. 3
FIG. 4
Housing
Reflector
Door Lens
NOTE: Do not connect DIM V+ (purple)/ DIM V- (gray) to line voltage or supply ground.
Easy Answersrablighting.comVisit our website for product info
RAB Lighting is committed to creating high-quality, aff ordable, well-designed and energy-effi cient LED lighting and controls that make it easy for electricians to installand end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]
INSTRUCTIONSW34 WALL PACK INSTALLATION
DIMENSIONAL DRAWINGS
W34-30L/35L
171/2”445mm
43/4”121mm
W34-55L/70L/90L
14’354mm
43/4”121mm
91/4”234mm
W34-150L
91/2”242mm
43/4”121mm
83/4”221mm
W34-IN-0619 RAB WARRANTY: RAB’S warranty is subject to all terms and conditions found at rablighting.com/warranty.