This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
INSTRUCTIONS
Page 1 of 14
*99TA526429* Instruction Sheet Number: 99TA516151D *99TA516151* (for RCD use only)
Description: Oil Accessory Kit and Universal Kit for Paragon Screw Compressors – Rev 9
Author: C.J.D. Date: April 17th, 2019
Kit Numbers: 6BTA000300 and 06TT660093
Kit: 06TT660093 (For all Paragon Compressor models, AC and Refrigeration).
QTY ITEM Carlyle Part Number QTY
1 Oil Accessory Kit 6BTA000300 1
2 2 Bolt Economizer Flange Kit 6BTA000309 1
3 4 Bolt Economizer Flange Kit 6BTA000310 1
4 018F4120 Oil & Motor Solenoid Coil, 230 vac 2
5 EF28BZ007 Motor Cooling Solenoid Valve 1
6 EA680045 Y-1037 Liquid Injection Valve 1
7 EF19ZZ003 Unloader solenoid coils, 230 vac 2
8 HK05YZ003 Suction Pressure Transducer 1
9 HK05YZ007 Discharge Pressure Transducer 1
10 6BTA000318 12mm terminal jam nuts & Grease 1
KIT: 6BTA000300 (This kit include in the 06TT660093 kit).
KIT: 6BUA000319 (For 06TU483, 554 and 06TV680, 753, 819Compressor Models) – For low voltage models 200V
and 230V
QTY ITEM Part Number
12 M16 x 2.00, Hex Nut Brass 8TU1307
1 Electrical Grease Compound 06TT660050
1 Instruction Sheet 99TA516149
1 Instruction Sheet 99TA516132
EA680045, Sporlan Y-1037 discharge liquid
injection valve. The valve provides discharge
temperature control by injecting liquid
refrigerant injection into the compressors
discharge line if discharge temperature rises above 190F.
Installation instructions
The compressor terminals are copper feed through pins with M12 or M16 metric threads. For M12 jam nuts,
torque to 15-20 ft-lb (20-27 Nm) and M16 jam nut, torque to 20-25 ft-lb (27-34 Nm). Install two jam nuts per
compressor terminal stud.
M12 Jam Nut, P/N 8TB0928 (TS, TT. TU, TV)
M16 Jam Nut, P/N 8TU1307 (TU, TV Low
Voltage 200V, 230V)
M12 Jam Nut, P/N 8TB0928 (TS, TT, TU, TV)
M16 Jam Nut, P/N 8TU1307 (TU, TV Low
Voltage 200V, 230V)
Must maintain a minimum GAP of 3mm
between the factory installed jam nut and the
field installed jam nut for all 6 compressor
terminal studs.
Terminal Grease 06TT660050:
Factory Installed Jam Nuts and Hardware.
Important: Disturbing this Nut can
jeopardize the seal integrity of the terminal Stud and Pin.
3mm
Slide Valve unloader coil, P/N EF19ZZ003
Install both slide valve unloader coils on the unloader valves as shown in the pictorial below. The coils are standard 230 vac.
The 5vdc suction pressure transducer sensor, Carlyle Part# HK05YZ003. The DC voltage can be measured across the Sig and Gnd terminals, and using the table below, can be converted to a pressure. PSIG = 33 * VDC – 16.5
The 5vdc Discharge Pressure Transducer sensor, Carlyle Part# HK05YZ007. The DC voltage can be measured across the Sig and Gnd terminals, and using the table below, can be converted to a pressure. PSIG = 101.594 * VDC - 47.33