Step 1: Begin with one of the floors. Note the arrow imprinted into the plastic. Place the floor on a hard surface. Step 2: Take a 6x18 black divider.The side with the outer most “arrow” snaps goes down. The word “Down” is also printed on the divider. Step 3: Insert the Arrows into the outer holes of the middle channel on the floor. Press firmly. You will feel the Arrows snap into place. • 1 Roof • 2 Floors • 2 Tan Sides • 4 Door Panels • 1 Attic Floor • 2 6x18 Dividers • 4 6x12 Dividers • 1 bag of 26 White Snaps Parts list: INSTRUCTIONS S&K 12 Family Purple Martin House Please read all directions before starting assembly. BH12 IF ANY ITEMS ARE DISCOVERED MISSING, CALL 1-800-764-8688 • DO NOT RETURN TO STORE. S&K Manufacturing, Inc. • 1001 Liberty Industrial Drive • O’Fallon, Mo 63366 www.skmfg.com • 1-800-764-8688 • Fax: 636-272-4044 Step 4: Interlock two 6x12 dividers via the slots in the 6x18 black divider. Press firmly on each end of the 6x12-inch dividers until you feel the Arrows snap into place. OPTIONAL: The living quarters in S&K’s House can be converted from a 6x6-inch to a 6x12-inch compartment. Simply remove the cut-out portions of walls and more space is created. Remove only one cut-out per compartment. Step 5: FIRST FL OOR ONL Y! IF USING AN S&K Tri-Tel/Quad-Tel Pole or adapter, push out the center pole guide area of the 6x18 black divider. Note the perforations for this. Step 6: Line up the next floor. The arrows on the flooring MUST point in the same direction. BE C AREFUL! If the arrows do not point in the same direction, your Purple Martin House will not be useable with an S&K Tri-Tel Pole, Quad- Tel Pole or adapter. The reason for the cut- out: When your house is completed, the S&K Pole or adapter will slide into the opening and snap into place with two snaps. Step 7: Place the second floor on top of the installed dividers. Line up carefully so that the dividers are within the wall channels. Step 8: When the dividers and channels are lined up and in place, push down firmly until the dividers’ arrows snap into place. NOTE: The arrows may appear to be bent after popping through. The strength of the dividers are not compromised. Step 9: For installing the dividers for the sec- ond floor of the house, repeat Steps 2 through 4. SPECIAL NO TE : If the House appears WARPED at this point, do not worry. It will straighten during the following steps. Step 10: Using the large black attic floor, punch out the 6 perforated rectangular slots completely. Step 11: Set the attic floor on the top of the sec- ond floor’s wall dividers. Line up the divider’s arrows with the slots in the attic floor and push each arrow through individually, by placing your fingers on each side of the slot and push- ing down firmly. Step 12: Turn the house on its side as shown. Step 13: Take one tan side - with the textured side facing up - and place it on the side of the house. Line up the perch rails’ points as shown. Step 14: Push the rails’ end tabs through each of the openings on each side of the house. Turn the house over and attach the second tan panel for the other side of the house in the same way, using Steps 12-14. Step 15: After both tan sides have been attached to the rails, take six snaps for attaching the tan side. Each snap hole has a correspon- ding hole on the outside of the floors. Be sure to line them up before inserting the snaps. (Shown in next step) NOTE: The smaller holes are for perches (optional) - it is not mandatory that the perch kit be used. Including “Purple Martin Basics” Special Martin Information www.skmfg.com 1-800-764-8688 For ideas on how to increase the size of living space for a martin family, see House Notes “E” (HN E): CREATING LARGER COMPARTMENTS, on the opposite side of this sheet. 11-2007v1 Eng ineer ing Note: After all the pieces of the S&K Martin House are correctly assembled the House will become V er y Solid .
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Step 1: Begin with one of the floors. Note thearrow imprinted into the plastic. Place thefloor on a hard surface.
Step 2: Take a 6x18 black divider. The side withthe outer most “arrow” snaps goes down. Theword “Down” is also printed on the divider.
Step 3: Insert the Arrows into the outer holes ofthe middle channel on the floor. Press firmly.You will feel the Arrows snap into place.
• 1 Roof• 2 Floors• 2 Tan Sides• 4 Door Panels
• 1 Attic Floor • 2 6x18 Dividers • 4 6x12 Dividers• 1 bag of 26 White Snaps
Parts list:
INSTRUCTIONSS&K 12 Family Purple Martin House
Please read all directions
before starting assembly.
BH12
IF ANY ITEMS ARE DISCOVERED MISSING, CALL 1-800-764-8688 • DO NOT RETURN TO STORE.
S&K Manufacturing, Inc. • 1001 Liberty Industrial Drive • O’Fallon, Mo 63366www.skmfg.com • 1-800-764-8688 • Fax: 636-272-4044
Step 4: Interlock two 6x12 dividers via theslots in the 6x18 black divider. Press firmly oneach end of the 6x12-inch dividers until youfeel the Arrows snap into place.
OPTIONAL: The living quarters in S&K’sHouse can be converted from a 6x6-inchto a 6x12-inch compartment. Simplyremove the cut-out portions of walls andmore space is created. Removeonly one cut-out percompartment.
Step 5: FIRST FLOOR ONLY! IF USING ANSS&&KK Tri-Tel/Quad-Tel Pole or adapter, push outthe center pole guide area of the 6x18 blackdivider. Note the perforations for this.
Step 6: Line up the next floor. The arrows onthe flooring MUST point in the same direction.
BE CAREFUL! If the arrows do not point in the
same direction, your Purple Martin House will
not be useable with an SS&&KK Tri-Tel Pole, Quad-
Tel Pole or adapter.
The reason for the cut-out: When your house iscompleted, the S&K Poleor adapter will slide intothe opening and snap intoplace with two snaps.
Step 7: Place the second floor on top of theinstalled dividers. Line up carefully so that thedividers are within the wall channels.
Step 8: When the dividers and channels arelined up and in place, push down firmly untilthe dividers’ arrows snap into place.
NOTE: The arrows may appear to be bent afterpopping through. The strength of the dividersare not compromised.
Step 9: For installing the dividers for the sec-ond floor of the house, repeat Steps 2 through 4.
SPECIAL NOTE: If the House appears
WARPED at this point, do not worry. It will
straighten during the following steps.
Step 10: Using the large black attic floor, punchout the 6 perforated rectangular slots completely.
Step 11: Set the attic floor on the top of the sec-ond floor’s wall dividers. Line up the divider’sarrows with the slots in the attic floor and pusheach arrow through individually, by placingyour fingers on each side of the slot and push-ing down firmly.
Step 12: Turn the house on its side as shown.
Step 13: Take one tan side - with the texturedside facing up - and place it on the side of thehouse. Line up the perch rails’ points as shown.
Step 14: Push the rails’ end tabs through eachof the openings on each side of the house.
Turn the house over and attach the second tan
panel for the other side of the house in the
same way, using Steps 12-14.
Step 15: After both tan sides have beenattached to the rails, take six snaps for attachingthe tan side. Each snap hole has a correspon-ding hole on the outside of the floors. Be sure toline them up before inserting the snaps. (Shownin next step) NOTE: The smaller holes are forperches (optional) - it is not mandatory that theperch kit be used.
Including“Purple Martin Basics”Special Martin Information
www.skmfg.com1-800-764-8688
For ideas on how to increase the size of living space for a martin family, seeHouse Notes “E” (HN E): CREATING LARGER COMPARTMENTS, on the opposite side ofthis sheet.
11-2007v1Engineering Note:After all the pieces of
the S&K Martin Houseare correctly
assembled the Housewill become Very Solid.
Related Documents
