INSTRUCTION MANUAL CLOCK RADIO WITH JUMBO LED DISPLAY

INSTRUCTION MANUALCLOCK RADIO WITH JUMBO LED DISPLAYMODEL: A61019

2

We declare that this product conforms to the following product legislation in accordance with the following directive(s):

2004/108/EC. Electromagnetic Compatibility Directive.2006/95/EC. Low Voltage Directive.2011/65/EU. Restriction of Hazardous Substances Directive.2009/125/EC Eco-Design of Energy Related Products1999/5/EC The Radio Equipment and Telecommunications Terminal Equipment Directive RKW Quality Assurance.

DECLARATION OF CONFORMITY

TECHNICAL DATA

GUARANTEE

This product is guaranteed for 12 months from the date of the original purchase.

If any defect arises due to faulty materials or workmanship, the faulty product must be returned to the place of purchase.

Refund or replacement is at the discretion of the retailer.

The following conditions apply: The product must be returned to the retailer with the proof of purchase.The product must be installed and used in accordance with the instructions contained in this instruction guide.

This item is for domestic purposes only.This guarantee does not cover wear and tear, damage, misuse or consumable parts.PFD has limited responsibility for incidental or consequential loss or damage.Valid in the UK and Eire only.

MODEL NO: A61019POWER: AC Adaptor 9V 400mA DC: 3V (1 X CR2025 BATTERY) NOT SUPPLIED

3

IMPORTANT INFORMATION - RETAIN FOR FUTURE USE

SAFETY INFORMATION

Important safety instructions – read carefully before use.It is important that this instruction manual should be retained with the appliance for future reference. These warnings have been provided in the interest of safety. You MUST read them carefully before installation or use.

WARNING

• Check that the voltage of the main circuit corresponds with the rating of the appliance before operating.

• Please ensure that the appliance is used on a stable, level, and heat resistant surface.

• Do not immerse cords, plugs or any part of the appliance in water or any other liquid.

• Do not leave the appliance unattended while it is operating.

• Close supervision is necessary when any appliance is used by or near children or pets.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• Switch off at the wall socket then remove the plug from the socket when not in use or before cleaning.

• If the supply cord or appliance is damaged, stop using the appliance immediately and seek advice from the manufacturer or its service agent or a similarly qualified person.

• Do not let the cord hang over the edge of a table or counter or let it come into contact with any hot surfaces.

• The use of accessory attachments is not recommended by the appliance manufacturer, apart from those supplied with this product.

• Do not pull the plug out by the cord as this may damage the plug and/or the cable.

• Do not use this product for anything other than its intended use.

• This appliance is for household use only.

• Do not carry the appliance by the power cord.

• Do not use the appliance outdoors.

4

IMPORTANT INFORMATION - RETAIN FOR FUTURE USE

• Do not place anything containing liquid on top of the unit

• Do not spill liquid onto the appliance. If this happens, mop up the liquid and seek advice from a qualified technician.

• Do not use next to a swimming pool.

• Do not put objects into any of the openings.

• Keep the unit free from dust, lint etc.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Only use attachments/accessories specified by the manufacturer

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Please ensure that the appliance has adequate ventilation

• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

• Caution marking is located at the bottom of apparatus.

• Do not play music at excessive level especially near children.

• Ensure the battery compartments are secure.

• Only use the batteries recommended.

• Ensure correct fit of batteries, observing the plus and minus marks on both the battery and the compartment.

• Replace a full set of batteries at one time.

• Store unused batteries in their packaging and keep away from metal objects that may cause a short circuit.

• Remove dead batteries from equipment.

• Remove batteries from equipment, if it is not to be used for a long time.

• Remember to keep button cell and AAA batteries away from children as they can easily be swallowed.

• Seek medical attention immediately if batteries are swallowed.

• Never dispose of batteries in a fire.

• Never attempt to recharge ordinary batteries.

• In the unlikely event the appliance develops a fault, stop using it immediately and seek advice from the service department: +44 (0) 333 220 6042

5

PACKAGE CONTENTS

FEATURES AND CONTROLS

INSTRUCTION MANUAL

CLOCK RADIO

AC ADAPTER

1. M Button

2. Left Button

3. Right Button

4. Snooze/Sleep

5. - Button

6. + Button

7. Power

8. LED Display

9. Sleep Indicator

10. Alarm 1 Indicator

11. Alarm 2 Indicator

12. Speaker (not shown)

13. DC Power Inout Jack (not shown)

14. Battery Compartment (not shown)

10

8

9 11

12

13

14

1 52 63 74

6

USING YOUR APPLIANCE

BEFORE FIRST USE

1. Remove the product from the box.

2. Remove any packaging from the product.

3. Please retain all packaging until you have checked and counted all the parts and the contents against the parts list.

4. Your appliance is now ready for normal use.

AC POWER SUPPLY

1. Plug the included AC Adaptor into a standard power point (100V-240V AC) and the other end into the Jumbo Alarm Clock Radio’s DC power input jack on the back of the unit (No.13 on the previous diagram).

2. Remove the protective film covering the LED display screen.

3. Follow the instructions contained in the next section of this instruction manual to ensure you get the most out of your Jumbo Alarm Clock Radio

BATTERY OPERATION

• This Jumbo Alarm Clock Radio features a battery back-up function which will maintain power to the unit in cases of mains power failure. 1 X CR2025 (3V) button cell battery (not included) may be installed into the back-up battery compartment which is located on the rear of the unit (No.14 on the previous diagram).

• In the event of a power outage, the time will not appear on the clocks display, however the clock will continue to operate and the correct time will be maintained until mains power returns. The back-up battery should be replaced as needed. Remove the battery if you are not using your clock radio for an extended period of time.

• To install the battery, lay the product face down on a sturdy surface that will not scratch the screen. The battery compartment panel is located in the centre of the stand and is secured with one (very small) Phillips head screw. Using a suitably sized screw driver, unscrew this panel and then remove the compartment panel (by pulling outwards from the top of the compartment panel). Place the 1 X CR2025 (3V) battery into the mould, ensuring that the + side of the battery is facing upwards (towards the rear of the unit). Replace the cover and screw it back in to secure.

SETTING THE TIME AND DATE

The Jumbo Alarm Clock Radio will allow you to update the Time, 24/12hr setting and the Date in one easy to follow process.

1. Press and hold the M Button for a few seconds. The ‘Hour’ digit(s) on the LED display will begin to blink on the LED display. Press either the or

button to adjust the ‘Hour’ digit(s). Once the correct ‘Hour’ is displayed press the M button to confirm.

7

2. The ‘Minute’ digits will now being to blink. Press either the or button to adjust the ‘Minute’ digits. Once the correct ‘Hour’ and ‘Minutes’ are displayed press the M Button to confirm.

3. Now press either the or button to select 12 or 24 hour time (shown on the screen as ‘12H’ or ‘24H’), once you have made your selection press the M Button to confirm.

4. The ‘Year’ will then begin flashing, press either the or button to adjust the year. Once the correct year is displayed, press the M Button to confirm.

5. The 2 numbers that are now flashing represent the current ‘Month’. You can press either the or button to adjust the ‘Month’ and then press the M Button to confirm.

6. Finally, flashing on the LED display will be the letter ‘d’ followed by 2 numbers. This represents the ‘Day’ of the month. You can press either the or button to adjust the ‘Day’ and then press the M Button to confirm.

7. The LED Display will now be showing the correct time and all of the changes you have made to the time and date will be saved.

SETTING THE ALARM

The Jumbo Alarm Clock Radio features 2 separate alarms to allow you flexibility to set different alarms for different days, such as weekdays and weekends. The below outlines how you can set both alarms in one simple process

1. Press and hold the ‘Power’ button for a few seconds. The first Alarm that you will be setting is Alarm 1. The current Alarm 1 time will be showing with the ‘Hour’ digit(s) flashing along with the Alarm 1 LED indicator flashing.

2. Press either the or button to adjust the ‘Hour’ digit(s). After the desired ‘Hour’ is displayed, press the Power button to confirm.

3. The ‘Minute’ digits will now being to blink. Press either the or button to adjust the ‘Minute’ digits. Once the correct ‘Hour’ and ‘Minutes’ are displayed, press the Power Button to confirm.

4. The next step is where you select what days you would like the alarm to be set for. Press either the or

button to select one of the options (on the next page) to choose the days you would like the alarm activated for. Once you have selected your desired setting, press the Power button to confirm.

1-7: Set on Every day of the week 6-7: Set on Saturday & Sunday 1-5: Set on Monday to Friday

1: Set on Monday only

2: Set on Tuesday only

3: Set on Wednesday only

8

4: Set on Thursday only

5: Set on Friday only

6: Set on Saturday only

7: Set on Sunday only

5. The next part of the process repeats steps 2-4 however, for Alarm 2. You will notice that the Alarm 2 LED indicator will be flashing to indicate this. Please repeat the process from steps 2-4 inputting the correct details for Alarm 2. Once you have completed this your settings for Alarms 1 and 2 will be saved.

TURNING THE ALARM ON / OFF

1. To turn the Alarm ON (once you have followed the previous instructions to set the alarms), you need to first determine which alarm you want to activate (Alarm 1 or Alarm 2) and ensure that the Jumbo Alarm Clock Radio is in normal mode (i.e. the radio is NOT on). If the radio is ON, the Alarm 1 and Alarm 2 buttons will function as volume increase/decrease buttons.

2. The Alarm can be set to sound as a BUZZER or as the LAST RADIO STATION PLAYED. If you set the alarm to BUZZER, your alarm will sound as a series of BEEP’s when it is activated. If you set your Alarm to the LAST RADIO STATION PLAYED, when your alarm sounds, it will simply turn on your radio to the last radio station played.

TO SET THE ALARM TO BUZZER

1. The ‘-’ button is the Alarm 1 button. To activate Alarm 1, press the ‘-’ button repeatedly until ‘bb’ is displayed on screen. Wait a few seconds until the clock reverts back to the current time and you will notice that the Alarm 1 LED indicator is illuminated, this indicates that Alarm 1 is on.

2. The ‘+’ button is the Alarm 2 button. To activate Alarm 2, press the ‘+’ button repeatedly until ‘bb’ is displayed on screen. Wait a few seconds until the clock reverts back to the current time and you will notice that the Alarm 2 LED indicator is illuminated, this indicates that Alarm 2 is on.

TO SET THE ALARM TO LAST RADIO STATION PLAYED

1. The ‘-’ button is the Alarm 1 button. To activate Alarm 1, press the ‘-’ button repeatedly until the frequency of the last radio station played is displayed on screen. Wait a few seconds until the clock reverts back to the current time and you will notice that the Alarm 1 LED indicator is illuminated, this indicates that Alarm 1 is on.

2. The ‘+’ button is the Alarm 2 button. To activate Alarm 2, press the ‘+’ button repeatedly until the frequency of the last radio station played is displayed on screen. Wait a few seconds until the clock reverts back to the current time and you will notice that the Alarm 2 LED indicator is illuminated, this indicates that Alarm 2 is on.

9

3. To turn the Alarm OFF you need to first determine which alarm you want to turn OFF (Alarm 1 or Alarm 2) and ensure that the Jumbo Alarm Clock Radio is in normal mode (i.e. the radio is NOT on). Press either the ‘-’ button (for Alarm 1) or the ‘+’ button (for Alarm 2) repeatedly until ‘OFF’ is displayed on screen. Wait a few seconds until the clock reverts back to the current time and you will notice that the relevant Alarm LED indicator is NOT illuminated, this indicates that the relevant Alarm is OFF.

USING THE SNOOZE FUNCTION

The Jumbo Alarm Clock Radio has a snooze function which allows you to stop the alarm from sounding for a period of approximately 9 minutes in order to allow you to ‘snooze’ and wake up more naturally.

When the alarm sounds, simply press the SNOOZE/SLEEP button on the top of the Jumbo Alarm Clock Radio (No.4 on the diagram on page 3). The alarm will then cease and restart in approximately 9 minutes.

TURNING THE ALARM OFF EACH DAY

To turn the Alarm OFF each day, simply press the Power button. The alarm will stop sounding and will not sound again until the next set day (i.e. if your alarm is only set for every Monday, the alarm will not sound until the following Monday).

USING THE DIMMER FUNCTION

The Jumbo Alarm Clock Radio has a Dimmer function which allows you reduce or increase the brightness of the LED display. When the Jumbo Alarm Clock Radio is in normal mode (i.e. the alarm is not sounding) simply press the SNOOZE/SLEEP button on the top of the Jumbo Alarm Clock Radio (No.4 on the diagram on page 3) to dim or increase the brightness.

TURNING THE RADIO ON / OFF AND SELECTING THE BAND

1. To turn the radio ON, simply press the Power button once, this will activate the FM radio.

2. If you wish to select the AM band press the Power button once again. Pressing the Power button will toggle between AM and FM radio.

3. To turn the radio OFF simply press and hold down the Power button for a few seconds until the radio ceases.

4. You can increase or decrease the Volume of the speaker, whilst the radio is turned ON. Simply press the ‘-’ button to decrease, or press the ‘+’ button. You can press the button repeatedly or hold the button down until you reach your desired volume level.

10

SEARCHING FOR RADIO STATIONS

• To search for radio stations, firstly ensure that the radio function is turned ON and is set to your desired band (AM or FM).

• You can perform an auto search where the tuner will automatically search up or down the frequency range and stop on the first available station. To do this press and hold either or buttons until you notice the frequencies display on screen start to change. After the tuner stops on the first available station, you can repeat the process until you reach your desired station.

• Pressing the will perform an auto search down the frequency range. Pressing the will perform an auto search up the frequency range.

• You can perform a manual search to find your desired radio station. To do this, simply repeatedly press (do not hold) either the or buttons to search up or down the frequency range until you reach the desired frequency/radio station.

USING THE RADIO STATION PRESET MEMORY

The Jumbo Alarm Clock Radio has a 20 station memory for the FM and AM tuners. You can save your favorite stations into the memory of the Jumbo Alarm Clock Radio so you can quickly tune to these stations. These presets can be overwritten at any time.

1. Tune the radio to your desired station (refer to page 9 for instructions).

2. Press and HOLD the M Button until ‘P01’ begins to flash on screen.

3. Press either the or buttons to select the preset you would like to save this to (from 1 – 20). Once you have reached your desired preset press the M Button once to save.

4. You can overwrite any preset at any time by following the previous procedure and ensuring you select the correct preset to overwrite with a NEW station.

5. If you would like switch to one of your saved radio stations, simply press the M button until ‘P01’ is displayed (assuming that you are listening to the station saved in the first preset). Press either the or buttons to move up or down your preset list. The saved stations will automatically play as soon as they are selected. After a few seconds, the Jumbo Alarm Clock Radio will display the time on screen once again.

USING THE SLEEP FUNCTION

The Jumbo Alarm Clock Radio has sleep function which enables you to listen to the radio for a selected period of time before the Jumbo Alarm Clock Radio will automatically turn the radio off.

1. When listening to the radio on your Jumbo Alarm Clock Radio, press and hold the SNOOZE/SLEEP button until ‘120’ is displayed on screen.

2. ‘120’ represents the number of minutes you would like your radio to continue to play before it turns itself off. You can press the snooze button repeatedly until you read your desired minute setting.

11

3. Once you have reached the desired amount on minutes simply wait a few seconds until the time is displayed on screen. You will notice the sleep LED indicator on the left hand side of the screen is illuminated and your Jumbo Alarm Clock Radio will automatically turn off the radio according to your selected time.

4. To cancel press and hold the SNOOZE/SLEEP button until you reach the minute select screen again (with your preselected minutes show. Press the SNOOZE/SLEEP button again repeatedly until the time is displayed on screen. The SLEEP time has now been cancelled and the SLEEP LED indicator will no longer be illuminated.

12

TROUBLESHOOTING THE APPLIANCE

PROBLEM POSSIBLE SOLOUTION

The Jumbo Alarm Clock Radio is not turning on.

Check the power adaptor is correctly connected at both ends.

There is no sound whilst in Radio Function

Check that the volume has been correctly adjusted. Check that the Clock is correctly set to Radio Mode. Check other radio stations.

Crackling whilst in radio mode.

Generally caused by a weak signal.Try adjusting the position of the antenna cable.Try a different radio station with better reception.

Alarm does not function.

Ensure that the Alarm time and frequency has been set correctly.Ensure that the Alarm has been correctly activated.Increase the radio volume.Ensure the radio has been tuned correctly to a station.

The Jumbo Alarm Clock Radio did not save original time during a power outage.

Change the back-up battery.

TROUBLESHOOTING THE APPLIANCE

13

CLEANING AND CARE

IMPORTANT:

1. Always disconnect the Clock Radio from the power supply and/or remove the batteries before cleaning.

2. Clean the Retro Radio with a soft, damp, lint free cloth.

3. Do not use abrasives or harsh cleaners.

14

ELECTRICAL SAFETY

IMPORTANTAs the colours in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, please proceed as follows:The wires in the mains lead are coloured in accordance with the following code:

Blue neutral [N] Brown live [L]

Plug Fitting Details (Where Applicable). The wire coloured blue is the neutral and must be connected to the terminal marked [N] or coloured black.The wire coloured brown is the live wire and must be connected to the terminal marked [L] or coloured red.On no account must either the brown or the blue wire be connected to the [EARTH] terminal .Always ensure that the cord grip is fastened correctly.The plug must be fitted with a fuse of the same rating already fitted and conforming to BS 1362 and be ASTA approved.If in doubt consult a qualified electrician who will be pleased to do this for you.

Non-Rewireable Mains Plug If your appliance is supplied with a non-rewireable plug fitted to the mains lead and should the fuse need replacing, you must use an ASTA approved one (conforming to BS 1362 of the same rating).If in doubt, consult a qualified electrician who will be pleased to do this for you.If you need to remove the plug - disconnect it from the mains - and then cut it off the mains lead and immediately dispose of its safely. Never attempt to reuse the plug or insert it into a socket outlet as there is a danger of an electric shock.

WARNING: This appliance is double insulated.

Do not connect any wire to the earth terminal.

15

RECYCLING

DISPOSAL OF THE UNIT

Appliances bearing the symbol shown here may not be disposed of in domestic rubbish. You are required to dispose of old electrical and electronic appliances like this separately.

Please visit www.recycle-more.co.uk or www.recyclenow.co.uk for access to information about the recycling of electrical items.

Please visit www.weeeireland.ie for access to information about the recycling of electrical items purchased in Ireland.

The WEEE directive, introduced in August 2006, states that all electrical items must be recycled, rather than taken to landfill.

Please arrange to take this appliance to your local Civic Amenity site for recycling, once it has reached the end of its life.

*REGISTER YOUR PRODUCT ONLINE AT WWW.AKAIONLINE.CO AND ENJOY 3 YEARS PEACE OF MIND.

GUARANTEE ONLY VALID WITH PROOF OF PURCHASE

AKAI CUSTOMER SERVICES+44 (0) 333 220 6042

0916.V1