Installing a HydroLink™ Watering System on your Trojan ... · EZGOZID • 0912 / TRJN_InstallationDiagram E-Z-GO E-Z-GO “RXV” 12-Volt Batteries Installing a HydroLink™ Watering
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
YID • 0912 / TRJN_InstallationDiagram
Yamaha
Yamaha 6-Volt Batteries
Yamaha 8-Volt Batteries
Yamaha “The Drive” 12-Volt Batteries - (2006 or newer)
Installing a HydroLink™ Watering System on your Trojan Batteries
IMPORTANT: For detailed installation instructions review Trojan’s Hydrolink™ Watering System with the Snake™ Tubing Manual included with your kit. Make sure to follow instructions on Page 4 of the manual before installing.
STEP 1Remove Current Vent Caps and Insert HydroLink™ Vents.
STEP 2Firmly Press HydroLink™ Vents Down. Ensure HydroLink™ vents are completely seated to avoid electrolyte spillage. WARNINg! Press in the HydroLink™ vent with your hands only - do not use a hammer.
STEP 3Install Snake™ Tubing Review the proper diagrams for correct Snake™ tube routing based on the application and manufacturers vehicle. Once reviewed, remove the red center plastic plug from the HydroLink™ vent.
Then snap each Snake™ plug into each HydroLink™ vent. Press firmly until your hear a click.
If you don’t hear a click, it has not been installed correctly.
Your HydroLink™ Watering System is now ready for use.
Correctly Installed Incorrectly Installed
InstallatIon DIagrams
For a Trojan master Distributor near you, call 800.423.6569 or + 1.562.236.3000 or visit www.trojanbattery.com12380 Clark Street, Santa Fe Springs, CA 90670 • USA
Trojan batteries are available worldwide through Trojan’s Master Distributor Network.We offer outstanding technical support, provided by full-time application engineers.
Installing a HydroLink™ Watering System on your Trojan Batteries
IMPORTANT: For detailed installation instructions review Trojan’s Hydrolink™ Watering System with the Snake™ Tubing Manual included with your kit. Make sure to follow instructions on Page 4 of the manual before installing.
STEP 1Remove Current Vent Caps and Insert HydroLink™ Vents.
STEP 2Firmly Press HydroLink™ Vents Down.Ensure HydroLink™ vents are completely seated to avoid electrolyte spillage. WARNINg! Press in the HydroLink™ vent with your hands only - do not use a hammer.
STEP 3Install Snake™ Tubing Review the proper diagrams for correct Snake™ tube routing based on the application and manufacturer vehicle. Once reviewed, remove the red center plastic plug from the HydroLink™ vent.
Then snap each Snake™ plug into each HydroLink™ vent. Press firmly until your hear a click.
If you don’t hear a click, it has not been installed correctly.
Your HydroLink™ Watering System is now ready for use.
Correctly Installed Incorrectly Installed
E-Z-GO “TXT” 6-Volt / 8-Volt Batteries* Terminal configuration may be differ on 8-Volt battery.
InstallatIon DIagrams
For a Trojan master Distributor near you, call 800.423.6569 or + 1.562.236.3000 or visit www.trojanbattery.com12380 Clark Street, Santa Fe Springs, CA 90670 • USA
Trojan batteries are available worldwide through Trojan’s Master Distributor Network.We offer outstanding technical support, provided by full-time application engineers.
Club Car “Precedent” 12-Volt Batteries - (2008 or newer)
Club Car “DS” 12-Volt Batteries - (2006 or newer)
Club Car “Precedent” 8-Volt Batteries - (2008 or newer)
Installing a HydroLink™ Watering System on your Trojan Batteries
IMPORTANT: For detailed installation instructions review Trojan’s Hydrolink™ Watering System with the Snake™ Tubing Manual included with your kit. Make sure to follow instructions on Page 4 of the manual before installing.
STEP 1Remove Current Vent Caps and Insert HydroLink™ Vents.
STEP 2Firmly Press HydroLink™ Vents Down. Ensure HydroLink™ vents are completely seated to avoid electrolyte spillage. WARNINg! Press in the HydroLink™ vent with your hands only - do not use a hammer.
STEP 3Install Snake™ Tubing Review the proper diagrams for correct Snake™ tube routing based on the application and manufacturer vehicle. Once reviewed, remove the red center plastic plug off the HydroLink™ vent.
Then snap each Snake™ plug into each HydroLink™ vent. Press firmly until your hear a click.
If you don’t hear a click, it has not been installed correctly.
Your HydroLink™ Watering System is now ready for use.
Correctly Installed Incorrectly Installed
InstallatIon DIagrams
For a Trojan master Distributor near you, call 800.423.6569 or + 1.562.236.3000 or visit www.trojanbattery.com12380 Clark Street, Santa Fe Springs, CA 90670 • USA
Trojan batteries are available worldwide through Trojan’s Master Distributor Network.We offer outstanding technical support, provided by full-time application engineers.